TOA | SR-TB4WP | manual | TOA SR-TB4WP User manual

WALL TILT BRACKET
SR-TB4WP
The SR-TB4WP is designed to be used exclusively to mount the
SR-S4LWP or SR-S4SWP Line Array Speaker on a wall. It allows
the speaker orientation angle to be adjusted to 0° or 5° vertically
and 20° max. horizontally.
In Combination with the optional SP-131 Speaker Mount Bracket
and YS-60B Pole Band, the SR-TB4WP also permits the speaker
to be mounted on an outdoor pole.
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the
instructions in this section for correct and safe operation.
• Be sure to follow all the precautionary instructions in this section,
which contain important warnings and/or cautions regarding
safety.
• After reading, keep this manual handy for future reference.
WARNING
Indicates a potentially hazardous situation which, if mishandled,
could result in death or serious personal injury.
• Refer all installation work to the dealer from whom the unit was
•
•
•
•
•
•
purchased. Installation requires extensive technical knowledge
and experience. The speaker may fall off if incorrectly installed,
resulting in possible personal injury.
Install the unit only in a location that can structurally support the
weight of the unit and the speaker. Doing otherwise may result in
the speaker falling down and causing personal injury and/or
property damage.
Owing to the speaker's size and weight, be sure that at least two
persons are available to install the speaker. Failure to do so
could result in personal injury.
Do not use other methods than specified to mount the bracket.
Extreme force is applied to the unit and the speaker could fall off,
possibly resulting in personal injuries.
Use nuts and bolts that are appropriate for the wall's structure
and composition. Failure to do so may cause the speaker to fall,
resulting in material damage and possible personal injury.
Tighten each nut and bolt securely. Ensure that the bracket has
no loose joints after installation to prevent accidents that could
result in personal injury.
Do not mount the unit in locations exposed to constant vibration.
The mounting bracket can be damaged by excessive vibration,
potentially causing the speaker to fall, which could result in
personal injury.
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
• Avoid touching the unit's sharp metal edge to prevent injury.
• Do not stand or sit on, nor hang down from the unit as this may
cause it to fall down or drop, resulting in personal injury and/or
property damage.
• Have the unit checked periodically by the shop from where it was
purchased. Failure to do so may result in corrosion or damage to
the unit that could cause the unit to fall, possibly causing
personal injury.
2. INSTALLATION
2.1. Munting on a Wall
Step 1. Install the bracket base on a wall.
Determine the orientation of the bracket base
depending on whether the speaker is to face left or
right.
Step 2. Attach the speaker mounting bracket to the bracket
base.
Horizontal facing angle can be adjusted in the range of
0° to 20°.
Turn the bracket base
upside-down to face the
speaker toward the right.
Hexagon head bolt M8 x 20
(supplied with the SR-TB4WP)
Bracket base
(component of the SR-TB4WP)
Speaker mounting bracket
(component of the SR-TB4WP)
[When facing the speaker
toward the left]
2
Speaker
1
Bracket base
Horizontal facing angle: 20°
Unit: mm
90
4-12 x 22
After the speaker's horizontal orientation has been
determined, fix the speaker mounting bracket to the base.
Note
The speaker's horizontal orientation can be adjusted after
the speaker has been installed.
Step 5. Mount the speaker to the speaker mounting bracket.
The vertical facing angle toward down can be adjusted
either 0° (horizontal) or 5° by the selection of the
screw mounting holes.
Vertical facing
angle: 5°
Vertical facing angle:
0° (horizontal)
Screws removed
in Step 3 (M5 x 20)
[Wall mounting dimensions]
WARNING
3
Bolts and nuts used to fix a bracket
base on a wall are not included. Use
bolts and nuts that are appropriate for
the construction of wall.
Step 1. Attach the SP-131 to the bracket base using bolts,
washers and nuts supplied with the SP-131.
Determine the orientation of the bracket base in
advance depending on whether the speaker is to face
left or right.
3. SPECIFICATIONS
Step 2. Install the SP-131 on a pole using the YS-60B.
The allowable pole diameter is 90 – 340 mm.
For the detailed mounting procedures of the SP-131
and YS-60B, see the instruction manual enclosed with
the SP-131.
The subsequent procedures follow Step2 or later in the
section "2.1. Mounting on a Wall."
SP-131 Speaker Mount Bracket
(optional)
Pole
Weight
Product Composition
Remove the 8 attached screws.
(The removed screws are used
in Step 4.)
2.2. Munting on a Pole
The optional SP-131 Speaker Mount Bracket and YS-60B Pole
Band are required to mount the speaker on a pole.
Number of Speakers
to be Mounted
Finish
Dimensions
Pad
Note
Take care not to remove the
pad at speaker mounting.
Waterproof washer
Step 3. Remove the attached screws (with waterproof
washers) on both sides of the speaker.
Step 4. Connect a speaker cable to the speaker.
5
ø60
Speaker mounting bracket
180
INSTALLATION MANUAL
1
1
Stainless steel (SUS304)
167 (w) x 247 (h) x 201 (d) mm
(complete assembly)
2.8 kg (including accessories)
Speaker mounting bracket ...... 1,
Bracket base ...... 1
Note: The design and specifications are subject to change without
notice for improvement.
• Accessories
Hexagon head bolt M8 x 20 ............................... 4
• Optional products
Speaker mount bracket: SP-131
Pole band:
YS-60B
2
Bracket base (component
of the SR-TB4WP)
[Example of pole mounted application]
Bolt*
YS-60B Pole Band
(optional)
* Supplied with the SP-131.
Washer*, Nut*
Speaker mounting bracket
(component of the SR-TB4WP)
URL: http://www.toa.jp/
133-01-442-8A

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project