TOA SR-S4SWP User manual

TOA SR-S4SWP User manual
zd TOA
LINE ARRAY SPEAKER SR—S4SWP
HDESCRIPTION
The SR-S4SWP is a two—way line array speaker ideal for short distance sound transmission and
configures a line array by arranging speaker elements vertically close to each other.
It satisfies the water protection requirements set down in the IPX4 Standard.
lt can be converted into the bi—amplifier drive system by changing the internal connection.
It can be used for high—impedance applications with the installation of the optional MT-S0601
Matching transformer.
BSPECIFICATIONS
Enclosure
Power Handling Capacity
Sealed type
Continuous program: 600 W (single-amp mode)
Low 240 W, High 240 W (bi-amp mode)
8 Q (single-amp mode)
Low 8 Q, High 8 Q (bi-amp mode)
Sensitivity 93 dB (1 W, 1 m)
Frequency Response
7/0 Hz — 20 kHz (when recommended parameters are applied by the optional DP-SP3)
Crossover Frequency 3.5 kHz
Rated Impedance
Directivity Angle Horizontal: 90°, Vertical: 10°
Speaker Component Low frequency: 10 cm cone-type X 8
High frequency: 2.5 cm balanced dome-type X 24
Connected Cable Direct cable withdrawal from internal speaker: 68.6 mm,
conductor cross section: 1.25 mm? 4—core cable, 3 m
Operating Temperature -—10 °С 10 +50 C
Water Protection IPX4
Finish Enclosure: Plywood, white, urethane coating
Front grille: Punched stainless steel, white, paint
Dimensions 160 (W) X 892 (H) X 305 (D) mm (excluding connected cable)
Weight 16 kg
Accessory Bi—amplifier drive rating label -1, Bi—amplifier drive input indication label -1
Option Matching transformer: MT-S0601, Extension plate: SR—EP4WP,
Wall tilt bracket: SR—TB4WP, Protection pad: SR—PP4,
Digital speaker processor: DP-SP3
BAPPEARANCE —
T Vi Lorisontal X
op lEW © © e
| 303 DEP
Lo |
160 255 AN
| 100 50| ©
ES
UNS + =
ON = ©
Ses = NOTE: В
< A 1. Install the speaker with its air hole
as \ = © down, os Indicated by the Up mark on
° ° — e speaker.
NO = 2. It features the water protection
tS © 9 construction (IPX4), however it is
ZN = о ° recommended that it be installed under
CO] = roofs, eaves, or other locations not
>” © 2 directly exposed to rain or snow.
7 — > 3. For outdoor permanent installation, the
| © = 1 O installation angle of the speaker must
VS< = — > be between O° horizontal and 30°
tz о ho O downward as shown at the above.
CN ho = TH > N Do not install the speaker horizontally.
O = E 4. When permanently installing the speaker
eS = | outdoors, inspect it periodically .
/ UN
LO] =
= G + .
<>” Black 3) Matching transformer
O = Red (N.C) mounting panel
o ). = White (N.C) (option)
E E
7 N
E = J |
NS = сл fs
>> 1 100,159 О = = =
Air hole (internal)
Front View Side View Rear View
UNIT:mm SCALE: 1/10
Na
OSA
TOA Corporation DWG No: GSRO17A1—7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement