TOA | SX-200IP | manual | TOA SX-200IP User manual

TOA SX-200IP User manual
INSTALLATION MANUAL
IP MODULE
SX-200IP
Thank you for purchasing TOA’s IP Module.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
WARNING
Indicates a potentially hazardous situation which,
if mishandled, could result in death or serious
personal injury.
• Do not expose the unit to rain or an environment
where it may be splashed by water or other liquids,
as doing so may result in fire or electric shock.
• Should the following irregularity be found during
use, immediately turn off the power supply to the
SX-2100AI Audio Input Unit where the SX-200IP
is installed and contact your nearest TOA dealer.
Make no further attempt to operate the unit in this
condition as this may cause fire or electric shock.
· If you detect smoke or a strange smell coming
from the unit
· If water or metallic object gets on the circuit board
· If the unit falls or breaks
· If it is malfunctioning (no tone sounds.)
2. GENERAL DESCRIPTION
The SX-200IP, designed to be installed in the SX-2100AI Audio input unit of the SX-2000 series, is an Interface
module for connection to the N-8000 series.
By connecting the SX-200IP to a network (LAN or WAN), paging announcements can be made to the SX-2000
system using the N-8000 series’ station(s) (N-8600MS and N-8610RM) employing the packet audio technology.
Each function is set by the dedicated setting software on a PC.
3. FEATURES
• Up to 8 SX-200IPs can be used per SX-2000 System.
• Paging announcements can be made to up to 8 SX-2000 systems using the SX-200IPs.
4. SPECIFICATIONS
Network Section
Network I/F:‌
Network protocol:
Connector:
Voice sampling frequency:
Indicator
Operation indicator (RUN)
Operating Temperature
Operating Humidity
Finish
Dimensions
Weight
10BASE-T/100BASE-TX (Automatic-Negotiation)
TCP/IP, UDP, HTTP, RTP, ARP, ICMP, IGMP
RJ45 connector for LAN
16 kHz, 8 kHz (controllable on the software)
48 kHz sample rate is used for SX-2000 system only.
Quantifying bit number:
16 bits
Voice encoding method:
Sub-band ADPCM, Cryptosystem
Voice packet loss recovery: Silence insertion
Audio delay time:
80 ms, 320 ms (controllable on the software)
0 to 40 ºC
90% RH or less (no condensation)
Panel: Pre-coated steel plate, black, 30% gloss
35 (w) x 119.5 (h) x 178.4 (d) mm
150 g
Note: The design and specifications are subject to change without notice for improvement.
5. MODULE INSTALLATION
Notes
• Make sure that the power is switched OFF before attaching or detaching SX-200IPs.
• To avoid failures due to static electricity, do not touch the parts on the SX-200IP circuit board.
• Ensure that the SX-200IP is installed and secured with screws in the correct position.
• Two silver slotted screws at the left and right sides of the front panel are handles used for module detachment.
Never rotate them because they do not function as screws.
Step 1. Remove the blank panel attached
to the SX-2100AI’s slot.
Step 2. Mount the SX-200IP.
Insert the SX-200IP and fix it in
place using the screws (Machine
screws M3 x 6) removed in Step 1.
SX-2100AI
SX-200IP
Handle
Machine screw M3 x 6
(screw removed in Step 1)
6. CONNECTION
2
1
Blank panel
SX-200IP
FOR SX-2000 SERIES ONLY
LAN
LINK/ACT 10/100M
RESET RUN
IP INTERFACE MODULE
model SX-200IP
RJ-45 connector
Note
Usable LAN cable is a STP Category 5 or greater straight through
cable only.
A UTP cable cannot be used.
LAN cable
To network
7. NOTES ON SETTING
It is necessary to perform SX-200IP setting using both the SX-2000 Setting software and N-8000 Setting software.
7.1. SX-2000 Setting Software
The SX-200IP is recognized as the “D-922E/F” in the SX-2000 system. Set the SX-200IP as the “D-922E/F” on
the SX-2000 Setting software. For the settings, read the SX-2000 Software instruction manual.
7.2. N-8000 Setting Software
For the settings, read chapter 5 of the N-8000 series instruction manual.
8. SX-200IP OPERATING REQUIREMENTS IN THE SX-2000 SYSTEM
• The SX-2000 Setting Software used for SX-2000 system settings should be Version 3.10 or later.
• The SX-2000 system components should be of the following firmware versions.
SX-2000SM, SX-2100AI, SX-2000AO, SX-2100AO
SX-2000CI, SX-2000CO
Version 3.10 or later
Version 2.01 or later
Warning
This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may
cause radio interference.
Traceability Information for Europe
Manufacturer:
Authorized representative:
TOA Corporation
TOA Electronics Europe GmbH
7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo, Japan
Suederstrasse 282, 20537 Hamburg, Germany
URL: http://www.toa.jp/
133-02-00318-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising