TOA | T-650 | manual | TOA T-650 User manual

TOA T-650 User manual
INSTRUCTION MANUAL
SPEAKER SYSTEM
T-650
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully
before use.
• Make sure to observe the instructions in this manual as
the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual
handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used
in this manual to prevent bodily injury and property
damage which could result from mishandling. Before
operating your product, read this manual first so you are
thoroughly aware of the potential safety hazards as well as
understand the safety symbols and messages.
WARNING Indicates a potentially hazardous
situation which, if mishandled, could result in death or
serious personal injury.
CAUTION Indicates a potentially hazardous
situation which, if mishandled, could result in moderate or
minor personal injury, and/or property damage.
· If you detect smoke or a strange smell coming from the
unit.
· If water or any metallic object gets into the unit
· If the unit falls, or the unit case breaks
· If it is malfunctioning (no tone sounds.)
CAUTION
When Installing the Unit
• When unpacking or moving a heavy speaker, be sure to
handle the unit with two or more persons. Falling or
dropping the speaker may cause personal injury and/or
property damage.
• Since installation requires specialized skills and
professional experience, always consult the shop from
where the unit was purchased before beginning
installation. If the speaker should fall, it could result in
electrical shocks or other personal injuries.
When the Unit is in Use
WARNING
• Do not operate the speaker for an extended period of
time with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate
and result in a fire.
When Installing the Unit
• Install the unit only in a location that can structurally
support the weight of the unit and the mounting bracket.
Doing otherwise may result in the speaker falling down
and causing personal injury and/or property damage.
When the Unit is in Use
• Should the following irregularity be found during use,
immediately stop operating the unit and contact your
nearest TOA dealer. Make no further attempt to operate
the unit in this condition as this may cause fire or electric
shock.
• Use only the specified matching transformer. If any other
matching transformer is used, it could cause damage to
the connected speaker, matching transformer itself, and
amplifier.
• Have the speaker unit checked periodically by the shop
from where it was purchased. Failure to do so may result
in corrosion or damage to the speaker or its mounting
bracket that could cause the speaker to fall, possibly
causing personal injury.
GENERAL DESCRIPTION
The TOA T-650 is a speaker system suited for use as a main speaker in indoor sports facilities or small and intermediate
halls.
FEATURES
•
•
•
•
•
High efficiency and high power handling capacity. Designed for high sound quality with an emphasis on intelligibility.
Heavy-duty construction protects unit against impacts from balls and other objects.
A short-distance horn and a long-distance horn are arranged for wide coverage with uniform sound quality.
Can be positioned at any angle of up to 15° to the left or right.
Optional matching transformer permits unit to be used as a high-impedance speaker.
APPEARANCE AND DIMENSIONS (IN MM)
[Speaker system]
Supplied M8 eyebolt mounting hole
Speaker mounting M8 hole (8 places)
Top view
Bottom view
354
288
Transformer installation
opening cover
827
10
40
Front view
Side view
[Speaker mounting bracket A]
Rear view
[Speaker mounting bracket B]
ø20 (Cable entry hole)
9x13 oval hole (for direct speaker attachment)
Axial hole
Angle adjustment slot
11x21 oval hole (for inclined speaker attachment)
30
60
69 69
207
240
133
MOUNTING THE SPEAKER ON THE WALL
1. Attach Speaker Brackets A and B to the upper and lower
parts of the wall using a total of eight bolts (four each per
bracket). (Note that the mounting position of Bracket A
or B differs depending on the direction in which the
speaker is inclined. Refer to the figures shown at the
lower right.)
207
69 69
60
827
887
Wall mounting dimension
WARNING
Check to ensure that the mounting surface is strong
enough to stand the weight of a load before
beginning installation.
represents the surface to
which the bracket attaches.
240
Speaker
mounting bolt
Cap
Note
Bolts for attaching the brackets are not supplied with the
unit. Use appropriate types depending on the material and
construction of the wall.
2. Remove caps filling in eight screw holes in the unit's top
and bottom panels. Insert two of the eight supplied
speaker mounting bolts into two central holes in the top
panel, then tighten the bolts so that their heads stick out
5-6 mm, as shown in the figure at right.
5 – 6 mm
Cap
Note
Take care that the speaker mounting bolt does not stick out
extremely.
Cable entry hole
3. Fit the mounted bolts into the two slots in the upper
bracket.
Eyebolt mounting hole
Memo
• Use the cable entry hole when the speaker cable needs
be left pulled out.
• It is also possible to lift up the speaker by means of an
eyebolt when installing it.
4. Fully inserting the bolts beyond the branch of the slot
temporarily secures the unit.
5. Insert the speaker mounting bolts into the remaining two
screw holes in the top panel. Use an oval hole for direct
speaker attachment located in the back of the bracket
when fitting the speaker's rear panel closely to the wall.
Use the angle adjustment slot and axial hole located in
the front of the bracket when adjusting angles.
Mounting
bracket A**
Mounting
bracket A*
Mounting
bracket B **
* Bracket arrangement when inclining the speaker to the
right.
** Bracket arrangement when inclining the speaker to the
left.
6. Determine a horizontal installation angle, then tighten all
of the four speaker mounting bolts. (Note that if the
speaker's back is fitted closely to the wall, you cannot
change the installation angle.)
7. Similarly, secure the lower mounting bracket to the
speaker's bottom surface using four speaker mounting
bolts.
Mounting
bracket B *
Axial hole
Angle
adjustment
slot
Oval hole for
direct speaker
attachment
15
Inclined speaker installation
(Maximum 15)
Direct speaker attachment
LARGE INPUT PROTECTOR
The T-650's short-distance tweeter has a circuit to protect the tweeter against extremely large input. (The connection of
the tweeter is cut off the instant the protection circuit is operated.) When the output volume level of high frequency sound
suddenly drops during use, this indicates the operation of the protection circuit. In such a case, turn down the amplifier
volume and wait until the protection circuit is automatically reset (2-20 seconds). When using the speaker again after the
circuit is reset, slightly decrease the amplifier volume than before.
ABOUT THE COMBINATION WITH OPTIONAL MATCHING TRANSFORMER
To install the MT-S0601 transformer in the speaker system,
remove the blank panel located at the back of the speaker
system. For the installation method, refer to the instruction manual
attached to the MT-S0601 transformer.
MT-S0601
Primary terminal
83 Ω
170 Ω
330 Ω
670 Ω
High impedance High impedance
100 V line
70 V line
–
60 W
60 W
30 W
30 W
15 W
15 W
7.5 W
SPECIFICATIONS
Enclosure
Power Handling
Rated impedance
Sound Pressure Level
Frequency Response
Crossover Frequency
Speaker Component
Input Terminal
Finish
Dimensions
Weight
Bass reflex type
Continuous pink noise: 120 W
Continuous program: 360 W
8Ω
100 dB (1 W,1 m)
80 – 20,000 Hz
1.2 kHz (passive network)
Low frequency: 25 cm cone speaker x 2
High frequency:
(for long distance use) CD horn fitted with compression driver (60 horizontal x 30 vertical)
(for short distance use) CD horn fitted with compression driver (90 horizontal x 40 vertical)
2-pole M5 screw terminal, distance between barriers: 12.2 mm
Enclosure: Coniferous plywood, black, semi-mat, urethane paint
Grille:
Steel plate, black, semi-mat, acryl paint
288 (w) x 827 (h) x 354 (d) mm
Speaker system: 20 kg, Mounting bracket: 2 kg
Note: The design and specifications are subject to change without notice for improvement.
• Accessories
Speaker mounting bracket A ........................... 1
Speaker mounting bracket B ........................... 1
Speaker mounting bolt ..................................... 8
Eyebolt ............................................................. 1
Traceability Information for Europe
Manufacturer:
TOA Corporation
7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo,
Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany
URL: http://www.toa.jp/
133-01-00222-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising