TOA VM-2240 ER User manual

TOA VM-2240 ER User manual
 % od Ti
Zl TOA SYSTEM MANAGEMENT AMPLIFIER
BDOESCRIPTION
09H
VM—2240
(CE— AU/ER)
The VM-2240 is a multifunctional amplifier that can be mounted in an ElA-Standard equipment
rack (3-unit size). The unit comes with 4 audio inputs including the background music input,
and the speaker output section which has an internal attenuator and 5-zone selector. It permits
not only general-purpose broadcast, but also Emergency Broadcast based on the EN60849 Standard
which gives
from an optional RM-200M
re—recorded voice instructions(*1) in the emergency situation. Broadcast can be made
Remote Microphone as well as from the amplifier, and can be remotely
controlled from external equipment. In addition, for 100 V/42 © application the unit features
the surveillance function(*2) which automatically checks the system for failures.
(x1) An optional EV-200M Voice Announcement Board is required.
(x2) An optional SV-200MA Surveillance Board is required.
BSPECIFICATIONS
(*3) 0 d8= 1 V
Power Source
AC: 230 V, 50/60 Hz
DC: 24 V/15 A, M3.5 screw terminal, Barrier distance: 8 mm (0.31”),
Applicable cable diameter: AWG22 — AWG14
Power Consumption
on AC Mains
With no signal present: 54 W
Under normal operating conditions according to
Е№60065: 1998 sec. 4.2: 255 W
With rated output signal: 549 W
Current Consumption
on 24 V DC Power Input
With no signal present: 1 A
Under normal operating conditions according to
EN60065: 1998 sec. 4.2: 5 À
With rated output signal: 14 A
Rated Output
240 W
Output Voltage
100 V/42 Q, 70 V/21 Q, 50 V/10 Q
/ Impedance (selectable by the internal wiring change)
Frequency Response 50 Hz — 16 kHz
Distortion 1 % or less
Signal-to-Noise Ratio
60 dB or more
Tone Control
Bass: 100 Hz +10 dB, Treble: 10 kHz +10 dB
(Inputs 1 — d and BGM individually adjustable.)
Remote Microphone
/Expansion Amplifier
2 RJ45 female connectors for connecting the RM—200M Remote
Microphone and the VM—-2120 or VM-2240 unit used as an
Connection expansion amplifier.
Maximum distance: 800 m (8/4.89 yd) in total
Link cable: Category 5 Shielded
Number of connectable RM-200M's: Up to 4
Twisted—Pair straight cable (TIA/EIA-568A standard)
Input Inputs 1 — 5: —60 dB(+5) (MIC)/—10 dB(+5) (LINE) (changeable),
600 Q, electronically balanced(x4),
combined XLR connector (female)/phone jack
(Only Input 1 is additionally equipped with DIN
connector(*o).)
Telephone paging input: Push—in terminal block(*6)
Voice sound: —10 dB(x3), 10 kQ, electronically—
balanced input with shield terminal(x4)
Control: No-voltage make contact input,
open voltage: 5.5 У DC,
short—circuit current: under 1 mA
BGM 1 — 2: =20 dB(x3), 10 kQ, RCA pin jack, monaural (internally mixed)
Power amplifier input: 0 dB(x3), 10 kQ, RCA pin jack
External speaker line input: 100 V line, for All-Zone Broadcast
(This input is selected when the “Unit's
broadcast cutoff” control is activated.)
Output Speaker output: Plug—in screw connector(*/)
O—zone selector with attenuator (all zones simultaneously
selectable)
Direct speaker line output: Direct output from the power amplifier
output transformer (attenuator bypassed),
Plug-in screw connector(*/)
Line output: 0 dB(x3), 10 kQ, RCA pin jack
Recording output: 0 dB(x3), 10 kQ, RCA pin jack
Preamplifier output: O dB(x3), 10 kQ, RCA pin jack
TOA Corporation
DWG No: GVMO1EB1—1(1/2)
J
7 dT
Я 1 TOA SYSTEM MANAGEMENT AMPLIFIER VM—2240
MSPECIFICATIONS (CE-AU/ER)
09H
Control Input For controlling Inputs 1 — 3, Push—in terminal block
No—voltage make contact input, open voltage: 3.5 V DC,
short—circuit current: 1 mA or less
Control Input and Output | D-sub connector (25-pin, female)
Input: No—voltage make contact input, open voltage: 3.3 V DC,
short—circuit current: 1 mA or less
Output: Open collector output, withstand voltage: 30 V DC,
control current: 10 mA or less
(1) External control input
Activation of messages (*8)
Activation of power
Activation and stop of Emergency Broadcast
Unit's broadcast cutoff
(when activated by an external emergency equipment)
(2) Status output
Irregularity of communications with the Remote Microphone and
an expansion amplifier
AC power condition
DC power condition
Irregularity of the sound source of the Voice Announcement Board
Failure (FAULT) indication on
Power switch on
External Attenuator Plug-in screw connector (*/), relay, no—voltage make contact output,
Control Output transfer type, withstand voltage: 50 V DC, 125 V AC,
contact current: 7 A (DC) or less, 7 A (AC) or less
Surveillance Input D—sub connector (25—pin, female)
and Output (x9) Input: No-voltage make contact input, open voltage: 5.5 V DC,
short-circuit current: 1 mA or less
Output: Open collector output, withstand voltage: 50 V DC,
control current: 10 mA or less
Power Supply 24 V DC/0.1 A, for supplying power to an optional Amplifier Control
Unit RU-2001/-2002, push-in terminal block (x6)
Chime Tone Built-in chime: 2-tone chime/2-tone chime (fast repeat)/4-tone
chime (Up)/Single-tone chime/4-tone chime (Up &
Down)/off
Voice Announcement Board sound source: Pre—recorded chime (6)
Function Two units stacking (VM-2120 or VM-2240)
Emergency broadcast (sequential control)
Broadcast priority control
Surveillance (failure detection) function (+9)
Power supply to only one Remote Microphone (RM-200M)
Line resistance: 40 © (one way) or less
Operating Temperature О °С 10 +40 C (32 °F to 104 °F)
Finish Panel: ABS resin, dark gray (PANTONE 447C or its equivalent), paint
Case: Steel plate, dark gray (PANTONE 446C or its equivalent), paint
Dimensions 419 (W) X 143.3 (H) X 355.7 (D) mm (16.5” x 5.64” x 14”)
Weight 14.5 kg (31.97 Ib)
Accessory Power cable (2 т (6.56 ft)) --1, Name label --1, Volume cover --4
Miniature type time-lag fuse 13.15 A |
Option Rack mounting bracket: MB—36
[nput transformer: 11-450
Voice announcement board: EV—200M
Surveillance board: SV-200MA
(*4) Can be transformer—balanced with the addition of an optional 11-450 input transformer.
(*5) For connection of the Paging Microphone PM—660D with a remote control switch
(x6) Usable cable diameter: AWGZ6 — AWGZ20, 0.5 mm?
(x/) Usable cable diameter: AWG24 — AWG12, 2.5 mm?
(*3) An optional EV-200M Voice Announcement Board is required.
The chime sound source must be pre-recorded into a CF (CompactFlash) card to be inserted into
the EV—200M Board.
(x9) An optional SV-200MA Surveillance Board is required.
J
TOA Corporation DWG No: GVMO1EB2—2(2/2)
% |
Zl TOA SYSTEM MANAGEMENT AMPLIFIER VM—2240
MAPPEARANCE (CE- AU/ER)
CPU RN COMPACTFLASH CARD LA
© оо °е ©
ACCESS —
EV-200M (view with the CF card
SV—200MA security cover removed)
13 SURVEILLANCE 1/0 1
Magnified view when each e Joo PERG:
optional board is mounted. =
SET CHECK
230V x- 50/60Hz DC POWER IN
м ®
T eage
SYSTEM MANAGEMENT AMPLIFIEZ
OUTPUT RATED 240W
TOA Corporation
ACCESS
PRE OUT LINE OUT BGM INPUT INPUT 3 INPUT INPUT oo
E ix
CONTROL 1/0 1
N1
ATTENUATOR | ©
CONTROL \2
©
EXTERNAL [ H
SP INPUT
c
DIRECT OUT _ y
100W(70/50V) ~
ZONE 1[ ç
Rear View
SP OUT
100V LINE
(70v/50V)
H
zone 2 |
H
Zone 3[ с
ZONE 4 [ |
5
1 zone 5[ |
© © ©
Model CE— AU ER
— Indication CE— AU —
om {FO TEED)
= ее === == AA = ао
Top View ~_ ~_ —
> CNY +
<
N
o
— 9
Rack mounting ©
bracket MB—36 | — — т 5
(option) | | ©,
| PO 7?
ee o y y
482 [18.987] 105
465 [18.31”] X с
419 [16.5”] || ©
ch +
ps nsc Aus VM— 2240 |
| =
à à © © © © ©0000 Y E
Front View с © © © © © 272 | LD,
7) «Cy. O. OY. OY. Y. 2 | ©
hone ra "INPUT 3 no oe 1 vo” 2 В 3 o” 4 oe 5 ALL —Y N
о ЭЭЭ | oe | > Me
—- — —-
4—6X10 [0.247 XO. 39" —
- 339[13.35”] 16.7 [0.66”] o |
| NO,
o als
7 || | a
Side View _
E ITT |
e
UNIT:mm SCALE:1/4
09H TOA Corporation DWG No: GVMO1EC1—2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement