Summit FF511L7NZ, FF511LBI7NZ, FS407LBI7NZADA, FS407LBI7NZ, FS407L7NZ, FF511LBI7NZADA Operating instrustions

CALIBRATED THERMOMETER/ALARM
USER MANUAL
Features
 Thermometer simultaneously displays minimum, maximum and current temperatures
 The unit will provide a visual and audio alert when temperature rises above or falls below the
high and low set points
 The min/max feature is designed to monitor and store the highest and lowest readings until the
memory is cleared
 The temperature sensor is enclosed in a glycol-filled bottle, protecting it from rapid temperature
changes when refrigerator/freezer door is opened
 Low battery alert function ( battery symbol flashes)
 Rear slide switch to select oC or oF temperature display
 Measuring temperature range -30 ~ 70 oC ( or -22 ~ 158 oF)
 Accuracy : ± 0.5 oC (-10 ~ 10 oC or 14 ~ 50 oF), in other range ± 1 oC ( or ± 2 oF)
 Alarm setting and alert on /off function
 Sampling rate of 10 seconds
 Powered by a durable AAA lithium battery
 6 ft (185 cm) probe-connecting cable
Felix Storch, Inc. │ Bronx, NY 10474│ Tel: (718) 893 3900│ Fax: (844) 478 8799
SAVE THIS MANUAL FOR FUTURE REFERENCE
R006-12282018
Package Contents
 Display unit
 Temperature sensor in a glycol-filled bottle
 Instruction manual


Calibration certificate
Lithium battery
*Remove the protective film that is applied to the LCD screen prior to using this product.
Parts and Controls/Features
Press the MODE/RESET button ONCE to reset Min/Max temperature record.
When the thermometer is sounding an alarm, press this button ONCE to turn off the
beeping sound.
From the main display screen:
Press ONCE to display high alarm temperature setting.
Press TWICE to display low alarm temperature setting.
Press THREE TIMES to display current temperature
reading.
Main display screen
When the thermometer is sounding an alarm, press this button ONCE to turn off.
However, the High-Alarm or Low-Alarm will still flash until the temperature goes
back to normal or the Low-Alarm function is turned off.
Set Up
Battery Installation: Remove battery compartment cover located on the rear of the unit and remove
insulation strip from battery compartment. Follow the polarity (+/-) diagram in the battery
compartment. Replace the battery cover. The unit will beep and all segments of the LCD will be
activated.
Switching between Fahrenheit and Celsius: To change the temperature display scale from Fahrenheit
(oF) to Celsius (oC) and back, slide the oC/oF button located on the rear of the unit.
R006-12282018
Operation
Programming the Alarms
To reset high alarm temperature setting and low alarm temperature setting, follow
instructions below.
From the main display screen:
High Alarm Temperature
Press HIGH/LOW key ONCE, then press MODE/RESET key to enter High
Setting
Low Alarm Temperature
Setting
Alarm temperature setting mode. Use the up and down arrows to adjust
temperature accordingly.
Press MODE/RESET key ONCE to confirm the setting.
From the main display screen:
Press HIGH/LOW key TWICE, then press MODE/RESET key to enter Low
Alarm temperature setting mode. Use the up and down arrows to adjust
temperature accordingly.
Press MODE/RESET key ONCE to confirm the settings.
By default the low and high alarm should be audible. To turn ALERT ON/OFF follow the instructions
below :
To make sure that the high temperature alarm is audible, press
Audible High Alarm Setting
HIGH/LOW key ONCE (to activate the HI-SET on the screen). Then
press the ALERT ON/OFF key ONCE to activate the HIGH-alarm
beeping sound. Press AGAIN to deactivate
Audible Low Alarm Setting
To make sure that the low temperature alarm is audible, press
HIGH/LOW key TWICE (to activate the LOW-SET on the screen). Then
press the ALERT ON/OFF key ONCE to
activate the LOW-ALARM beeping sound.
Press AGAIN to deactivate.
For an activated Hi-alarm and Lo-alarm
buzzer, the display will indicate Hi-Alarm
and Lo-Alarm as shown :
To Use
 Once the Alarm Thermometer has been programmed, place the temperature sensor (in glycol bottle) in
the location to be monitored, such as inside a refrigerator or freezer. Attach thermometer to the door of
the unit with magnet on back of the thermometer, or place it on a table or shelf where it can be easily
seen and heard.
 Thermometer displays internal temperature of unit being monitored, as well as maximum and
minimum temperatures reached. The thermometer maximum and minimum readings reflect the
highest and lowest temperatures since the battery was inserted or since the RESET button was last
pressed.
 If the temperature measurement rises above or falls below the set temperature range, the alarm will
sound. To silence the alarm, press ALERT ON/OFF button.
 Set the high and low alarm temperature limits above and below the refrigerator/freezer operating
temperature to prevent false alarms. Refrigerators are designed to run between 2-8 °C (36-46°F) while
freezers run below -15 °C (5 °F).
R006-12282018
Troubleshooting
Displays „NP‟
The temperature sensor is not installed correctly.
Display screen not working
Make sure the battery is installed correctly. Battery may
need to be replaced.
Battery may need to be replaced.
“Low battery” indicator flashing
Care & Maintenance
•
•
•
•
•
•
Do not disassemble the product, as product damage may result.
Store the product where it will not be exposed to direct sunlight, dust or high humidity.
Do not wash or expose the product to water or other liquids.
Clean the product by wiping with a soft, dry cloth.
Never use volatile or abrasive liquids or cleaners to clean the product.
Do not drop the product or subject it to sudden shock or impact.
Customer Support
For technical support, please call 800-932-4267 (U.S. and Canada) or email
[email protected]
For more information, please call ACCUCOLD at 718-893-3900 (U.S. and Canada). See us
on the web at www.summitappliance.com
For re-calibration and certification questions, please email us at [email protected]
Limited Warranty
SUMMIT products have a limited warranty period of 1 year against defects in materials and
workmanship from the date of purchase. Accessory items and sensors have a limited warranty
of 3 months. Repair services have a limited warranty period of 3 months against defects in
materials and workmanship. SUMMIT shall, at its option either repair or replace hardware
products that prove to be defective, if a notice to that effect is received within the warranty period.
SUMMIT makes no other warranties or representations of any k ind whatsoever, expressed or
implied, except that of title, and all implied warranties including any warranty of merchantability
and fitness for a particular purpose are hereby disclaimed.
WARNING: This product can expose you to chemicals including Nickel
(Metallic) which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov
Note: Nickel is a component in all stainless steel and some other metal components.
Summit, Div of Felix Storch, Inc. • Bronx, NY 10474 • Tel: 718-893-3900 • Fax: 844-478-8799
R006-12282018

Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project