Barco PGWX-61B User guide

Barco PGWX-61B User guide
Command Catalog
1011000110100100101100101001010101010010100101
1010011001010100100100100100111010100101000101
0110110001001010011001100101010010010010101010
1011000110100100101100101001010101001001001010
1010011001010100100100100100111010100100101010
0110110001001010011001100101010010100101001010
1011000110100100101100101001010101110101100101
1010011001010100100100100100111011001001010101
0110110001001010011001100101010010100100110101
1011000110100100101100101001010101010010100101
1010011001010100100100100100111010100101000101
1011000110100100101100101001010101001001001010
1010011001010100100100100100111010100100101010
0110110001001010011001100101010010100101001010
1011000110100100101100101001010101110101100101
1010011001010100100100100100111011001001010101
Reference manual
For PGWX-61B
R5905745/03
07/05/2015
Barco NV
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.36.883.86
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Printed in Belgium
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site
https://www.barco.com/en/signin.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.
Table of contents
TABLE OF CONTENTS
1. Introduction . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3
1.1
About this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. The Barco Projection Protocol. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 5
2.1
2.2
2.3
2.4
The Barco Projection Protocol explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Ethernet communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
RS232/RS422/USB-B communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
The command representation in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. Commands .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 13
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
3.18
3.19
3.20
3.21
3.22
3.23
3.24
3.25
3.26
3.27
3.28
3.29
3.30
3.31
3.32
3.33
3.34
3.35
3.36
3.37
3.38
3.39
3.40
3.41
3.42
3.43
3.44
3.45
3.46
3.47
3.48
3.49
3.50
3.51
3.52
3.53
3.54
3.55
3.56
3.57
3.58
3.59
3.60
3.61
3.62
3.63
AV mute, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
AV mute, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
decrement noise reduction, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
get about info, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
get advanced control info, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
get aspect ratio file, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
get auto image adjust, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
get auto power off, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
get auto power on, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
get auto source, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
get brightness, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
get ceiling mode, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
get color temperature, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
get color wheel index, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
get contrast, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
get diagnostics info, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
get dimming, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
get display mode, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
get format, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
get freeze, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
get gamma, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
get general info, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
get geometry adjust info, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
get H start, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 39
get high altitude, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
get image setting info, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
get input black balance, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
get input selection, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
get input white balance, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
get internal pattern, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
get IP configuration info, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
get lamp max runtime, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
get lamp on, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
get lamp runtime, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
get lamp status, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
get language, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
get main zoom, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
get menu position, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
get no signal color logo, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
get noise reduction, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
get phase, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
get PIP enable, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
get PIP position, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
get PIP select, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
get PIP size, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 60
get rear projection mode, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
get resolution, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
get saturation, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
get serial number, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
get sharpness, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
get tint, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
get V start, read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
get versions, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
get warp keystone vertical, read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
increment noise reduction, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
reset settings to factory defaults, write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
set aspect ratio file, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
set auto image adjust, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
set auto power off, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
set auto power on, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
set auto source, write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
set brightness, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
set ceiling mode, write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
R5905745 COMMAND CATALOG 07/05/2015
1
Table of contents
3.64
3.65
3.66
3.67
3.68
3.69
3.70
3.71
3.72
3.73
3.74
3.75
3.76
3.77
3.78
3.79
3.80
3.81
3.82
3.83
3.84
3.85
3.86
3.87
3.88
3.89
3.90
3.91
3.92
3.93
3.94
3.95
3.96
3.97
3.98
3.99
set color temperature, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
set color wheel index, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
set contrast, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
set dimming, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
set display mode, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
set format, write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
set freeze, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
set gamma, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
set H start, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
set high altitude, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
set input black balance, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
set input selection, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
set input white balance, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
set internal pattern, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
set language, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
set lens center, write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
set lens focus, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
set lens shift, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
set lens zoom, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
set main zoom, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
set menu position, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
set no signal color logo, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
set noise reduction, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
set phase, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
set PIP enable, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
set PIP position, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
set PIP select, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
set PIP size, write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
set projector power on/off, write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
set rear projection mode, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
set saturation, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
set sharpness, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
set TCP/IP, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
set tint, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
set V start, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
set warp keystone vertical, write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Index. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 115
2
R5905745 COMMAND CATALOG 07/05/2015
1. Introduction
1. INTRODUCTION
R5905745 COMMAND CATALOG 07/05/2015
3
1. Introduction
1.1
About this document
What is the purpose of this document?
This document is applicable for the Barco device mentioned on the front page of this document and can thus not be used on any
other equipment.
It explains how the communication with the device is accomplished. In order to be able to communicate with this Barco device, the
Barco Projection Protocol, which is explained in detail in the following chapter, must be strictly followed.
Audience & prerequisites
This document is intended for software programmers and system integrators who want to be able to control a Barco device from
their own application. This document expects a basic knowledge of binary math, networking technology and programming.
4
R5905745 COMMAND CATALOG 07/05/2015
2. The Barco Projection Protocol
2. THE BARCO PROJECTION PROTOCOL
Overview
•
The Barco Projection Protocol explained
•
Ethernet communication
•
RS232/RS422/USB-B communication
•
The command representation in this manual
R5905745 COMMAND CATALOG 07/05/2015
5
2. The Barco Projection Protocol
2.1
The Barco Projection Protocol explained
Usage
The Barco Projection Protocol is used for the serial communication with a Barco device. This can be done by the following ways:
•
Ethernet
•
RS232
•
RS422
•
USB-B
Structure
Each command is built up from a start byte, device address, request/response, checksum and stop byte (image 2-1).
Start byte
Device address
1 byte (0xFE)
1 byte
Request /
Response
1..n bytes
Checksum
Stop byte
1 byte
1 byte (0xFF)
Image 2-1
Command structure
•
Start byte: used to let the receiver know that a command will follow.
•
Device address: when multiple devices (maximum 256) are connected on the same physical connection, the device address
is used to specify the device (only for RS232 connections). In case of an Ethernet connection, this should be set to 0.
•
Request/Response: the actual command bytes.
•
Checksum: used to detect if any errors occurred during transmission or reception of the command.
•
Stop byte: used to let the receiver know that the end of a command has been reached.
How is the checksum calculated?
The checksum calculation is based on modular arithmetic:
Checksum = (Device address + Request/Response) modulo 0x100 (or 256)
Bytes conversion
Some bytes cannot be used in a command. If they do appear in the request/response or checksum, they must be converted. The
table below gives an overview.
Byte
After conversion
0x80
0x80 0x00
0xFE
0x80 0x7E
0xFF
0x80 0x7F
When a byte sequence from the after conversion column is received, that sequence must be converted to the
corresponding byte.
Characters and character strings
Each character is sent as a byte, using the ANSI encoding method.
Character strings can be formatted in two ways:
•
C-style format
An array of one or more characters which is terminated by a NULL character (0x00). The position of the NULL character
determines the length of the string.
Example: ’f’ ’o’ ’o’ ’ ’ ’b’ ’a’ ’r’ 0x00
•
Pascal-style format
An array of one or more characters which is started (the first byte) with the length of the string. Therefore, Pascal-style strings
are limited to 255 characters.
Example: 0x07 ’f’ ’o’ ’o’ ’ ’ ’b’ ’a’ ’r’
ANSI
American National Standards Institute
6
R5905745 COMMAND CATALOG 07/05/2015
2. The Barco Projection Protocol
Data words
A data word is a value which consists of multiple bytes. Data words are formatted in big endian.
How to calculate the value of a data word?
Example of a 4-byte value: 0x01 0x20 0x50 0x30
= (0x01 * 256^3) + (0x20 * 256^2) + (0x50 * 256^1) + (0x30 * 256^0)
= (1 * 16777216) + (32 * 65536) + (80 * 256) + (48 * 1)
= 16777216 + 2097152 + 20480 + 48
= 18894896
msb
The most significant byte, is the byte with the greatest weight (value).
lsb
The less significant byte, is the byte with the smallest weight (value).
Big endian
When the first byte of a data word is the msb and the last byte is the lsb, the data word is in big endian.
Negative values
The two’s complement (2-complement) system is used for the representation of negative values.
Acknowledgement (ACK and NACK)
If a command is received, the receiver will check the validity and correctness of the command before processing it. If the command
is understood, the receiver will first acknowledge the command before doing the actual processing of the command. An ACK (ACKnowledge) is sent when these conditions are met:
•
The command format is correct
•
The command and its parameters are valid
•
The checksum is correct
When these conditions are not met, a NACK (Not ACKnowledge) is sent.
ACK
NACK
Byte 1
0x00
0x00
Byte 2
0x06
0x15
When the sender receives a NACK message, it is up the sender to decide what should happen next: retry sending the command or
discard the command.
Acknowledgements are not used in multicast communication.
Sending and receiving a command
A command which is sent to the device will consist of a request. A command which is received by the client will consist of a response.
Requests must be sent in the Barco Projection Protocol format: each request needs to be structured in the correct way before it is
sent to the device. Responses are also sent in the Barco Projection Protocol format.
Keep in mind that:
•
For Ethernet communication, the Device address must be set to 0.
•
A correct Checksum must be generated for the command.
After a request has been sent to the device, the acknowledgement of the request must be read first. After the request has been
acknowledged, the response from the device (if applicable) can be expected.
Example 1: The client wants to know the type of the device. It sends the following command: projector type, read. The device will
acknowledge (ACK) the request and then send the response which contains the device type.
R5905745 COMMAND CATALOG 07/05/2015
7
2. The Barco Projection Protocol
(1) projector type, read - request
Client
(2) ACK
Device
(3) projector type, read - response
Image 2-2
Example 1
Example 2: The client sends an unknown command. The device doesn’t recognize the command and sends a NACK.
(1) unknown command
Client
(2) NACK
Device
Image 2-3
Example 2
How to handle failing communication?
When a sender fails to send a command, or a receiver fails to return the expected response (ACK, NACK or response), some steps
must be followed to handle this failing communication.
There are 2 possible failures:
•
Communication link problems: if the sending of the commands itself doesn’t work, it will be because the communication is
broken (e.g. the receiver is disconnected from the network).
•
Answer back problems: when commands can be sent out but no response is sent back, it means that the communication link
is OK but the receiver is unable to answer back.
Each type of failure needs another way of handling.
Handling communication link problems
As communication link problems will most likely have a physical reason (cable disconnected, hub down, device down, …), the user
must be notified and must be asked for his feedback. In most cases there will be a user intervention needed to correct this problem
(connect the cable, reboot the hub, restart the device, …).
The actual implementation of this should be described in the specifications of the application.
Handling answer back problems
Answer back problems should be addressed in another way. When a receiver fails to answer back it might be that it is currently too
busy to answer back. The application software should implement some simple mechanisms to avoid problems when this occurs:
1.
Timeout waiting: the application should wait for a limited amount of time for an answer (e.g. max 10 seconds). This ensures
that the application can react when a command doesn’t get answered in time.
2.
Retry waiting: if the timeout expires, one can retry waiting for the answer. By doing this, the user has the opportunity to cancel
the action. If needed, the retry can even be repeated several times.
3.
Retry sending: when a command does not get answered after the timout waiting and retry waiting, the command is considered
to be lost in action and the application should send the command again.
This mechanism follows the sequence of the steps: first the timeout waiting is used, then the retry waiting and finally the retry
sending. If all of these steps fail, there might be a major problem with the receiver. In this case the user should be notified of these
problems so that he can check the status of the receiver.
8
R5905745 COMMAND CATALOG 07/05/2015
2. The Barco Projection Protocol
2.2
Ethernet communication
Introduction
The communication follows a client/server model where the device is the server. This means that the device responds on requests
that are sent by a client. The device will not send out messages on its own initiative.
The communication is blocking which means that when a request is sent to the device, no other requests can be sent until the device
has responded on the first request. The communication blocks for each request.
The connector used for the Ethernet ports are of rugged Neutrik EtherCon RJ45 type, which is compatible with
standard RJ45 cable connector. Straight (most common) as well as cross linked network cables can be used.
10/100 Base-T — RJ45 port
Pin
Description
1
TXD+
2
TXD-
3
RXD+
4
—
5
—
6
RXD-
7
—
8
—
Making connection with the device
The device is listening on TCP port 0xAAA0 (43680) for incoming connections. The IP address can be retrieved using the local user
interface or on the OSD menu of the device.
Device discovery
It is possible to discover all the devices on the network using a UDP broadcast. A UDP broadcast only works on IP networks and
requires a special socket connection: the datagram connection.
Device 1
Device 2
Client
LAN
Device n
Image 2-4
To discover the devices, send a datagram packet to the broadcast address 255.255.255.255 on port 0xA001.
The packet should contain 1 byte: 0x3F, which represents the character ‘?’.
All the devices that support UDP broadcast discovery, will answer on the request by sending an array of (C-language) strings on the
same socket. Each string represents a key-value pair with specific information about the device that has been discovered.
R5905745 COMMAND CATALOG 07/05/2015
9
2. The Barco Projection Protocol
Typically, the following strings will be returned:
•
hostname=value; the hostname of the device
•
ip-address=value; the IP address of the device
•
mac-address=value; the MAC address of the NIC on the device
•
type=value; the device type (not for DP90/DP100 projectors)
Remarks:
•
The broadcast does not follow the typical Barco Projection Protocol formatting: the request is just one byte (not marked up
as Barco Projection Protocol command) and the devices answer back without sending an ACK and without formatting their
response in the Barco Projection Protocol format.
•
The size of the array is undetermined, but in most cases it will contain 4 strings. However, this is open to future expansion, so
more strings can be added later.
•
The strings normally appear in this order: hostname, ip-address, mac-address and type, but this cannot be guaranteed.
The used broadcast is a limited broadcast. This means that the broadcast message is transmitted to all NIC’s
which are on the same IP segment as the client. This type of broadcast is not forwarded by routers so it will
not detect devices which are on another segment.
NIC
Network Interface Card
10
R5905745 COMMAND CATALOG 07/05/2015
2. The Barco Projection Protocol
2.3
RS232/RS422/USB-B communication
RS232
An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the communication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for
relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard
with a set number of conductors, data rate, word length and type of connector to be used. The standard specifies component connection standards with regard to computer interface. It is also called RS-232-C, which is the third version
of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical ’0’ is > + 3V, Logical ’1’ is < 3V. The range between -3V and +3V is the transition zone.
RS422
An EIA serial digital interface standard that specifies the electrical characteristics of balanced (differential) voltage,
digital interface circuits. This standard is usable over longer distances than RS-232. This signal governs the asynchronous transmission of computer data at speeds of up to 920,000 bits per second. It is also used as the serial port
standard for Macintosh computers. When the difference between the 2 lines is < - 0.2V that equals with a logical ’0’.
When the difference is > +0.2V that equals to a logical ’1’..
Settings
Baud rate: Defines the speed of the data transfer. The baud rate can be set using the local user interface on the device. Consult
the user manual of the device for more detailed information.
Data bits: Eight (8) data bits are used for each character of the data transfer.
Parity: There is no parity bit used to perform error checking.
Stop bit: One (1) stop bit is used to define the end of a character.
Hardware
RS232/422 input (Sub-D) port
Pin
Description
1
DCD : Data Carrier Detect
2
RXD- : Receive Data
3
TXD- : Transmitted Data
4
DTR : Data Terminal Ready [RS232]
TXD+ : Transmitted Data [RS422]
5
GND : Ground
6
DSR : Data Set Ready [RS232]
RXD+ : Received Data [RS422]
7
— (not connected) —
8
CTS : Clear To Send
9
RI : Ring Indicator
R5905745 COMMAND CATALOG 07/05/2015
11
2. The Barco Projection Protocol
2.4
The command representation in this manual
About the command representation in this manual
•
Title: The title of a command is built up from its function (e.g. network settings), followed by its type (e.g. read).
•
Description: A general description of the command is given in the About this command section.
•
Request/Response table: Each row in the request/response table represents a datafield. A datafield contains 1 or more values.
a) Pos: The position of the datafield. When the size of the datafield is greater than 1, the datafield will take more than 1 position.
b) Size: The number of values the datafield must contain. This can be different from the total number of available values,
dependent on the value groups.
c) Name: The name of the datafield.
d) Description: The description of the datafield.
e) Content: The value(s) of the datafield. This column consists of the value itself, and a value description. Every value is
displayed in a separate row. A datafield can have different value groups.
Different value groups can be distinguished as follows:
-
If consecutive rows have different background colors, the values belong to another group.
-
If they have the same background color, the values belong to the same group.
Only 1 value group per datafield may be choosen to be used in the command. All the values of a value group must appear
together and in the same order.
Example: the datafield below contains 2 IP addresses. Only 1 of the 2 IP-addresses may be choosen in the command. The values
of the IP-addresses must stay in the same order.
Pos
Size
0-3
4
Name
IP-address
Description
This is the IP-address datafield.
Content
192
IP-address 1, value 1 (dec)
168
IP-address 1, value 2 (dec)
1
IP-address 1, value 3 (dec)
1
IP-address 1, value 4 (dec)
192
IP-address 2, value 1 (dec)
168
IP-address 2, value 2 (dec)
1
IP-address 2, value 3 (dec)
2
IP-address 2, value 4 (dec)
Table 2-5
Example
12
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3. COMMANDS
R5905745 COMMAND CATALOG 07/05/2015
13
3. Commands
14
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.1
AV mute, read
About this command
This command reads the AV mute status. When AV mute is set to On, the screen will be black.
Request
Pos
Size
0
1
get adj
Name
1
1
AV mute
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xa9
Response
Pos
Size
Name
0
1
get adj
1
1
AV mute
0xa9
2
1
AV mute status
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
15
3. Commands
3.2
AV mute, write
About this command
This command will turn the screen black when AV mute is set to On. When AV mute is set to Off, the screen will turn back to the
original image.
Request
16
Pos
Size
Name
Description
0
1
set adj
1
1
AV mute
0xa9
2
1
AV mute status
0x00
Off (hex)
0x01
On (hex)
byte value known as "set adj"
Content
0x20
set adj (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.3
decrement noise reduction, write
About this command
This command decrements the noise reduction by one.
Request
Pos
Size
0
1
dec adj
Name
1
1
adj noise reduction
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "dec adj"
Content
0x23
dec adj (hex)
0x73
adj noise reduction (hex)
17
3. Commands
3.4
get about info, read
About this command
This command gets the "about" info of the projector.
Request
Pos
Size
0-2
3
Name
Description
get about info
Content
0x2A
0x01
0xA2
Response
Pos
Size
0-2
3
Name
Description
get about info
Content
0x2A
0x01
0xA2
3
4-13
1
10
model name
0x02
PGXG-61B (hex)
0x03
PGWX-61B (hex)
0x04
PGWU-61B (hex)
serial number
BYTE1 (hex)
BYTE2 (hex)
BYTE3 (hex)
BYTE4 (hex)
BYTE5 (hex)
BYTE6 (hex)
BYTE7 (hex)
BYTE8 (hex)
BYTE9 (hex)
BYTE10 (hex)
14-19
6
system FW version
BYTE1 (hex)
BYTE2 (hex)
BYTE3 (hex)
BYTE4 (hex)
BYTE5 (hex)
BYTE6 (hex)
20
21
1
1
main source
PIP source
0x00
HDMI (hex)
0x01
VGA (hex)
0x02
DVI (hex)
0x03
BNC (hex)
0x04
CVBS (hex)
0x1A
invalid (hex)
0x00
HDMI (hex)
0x01
VGA (hex)
0x02
DVI (hex)
0x03
BNC (hex)
0x04
CVBS (hex)
0x1A
22
18
1
pixel clock
pixel clock (MHz) (integer)
invalid (hex)
pixel clock (dec)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
Pos
Size
23
1
pixel clock
pixel clock (MHz) (decimal fraction *
256)
pixel clock (dec)
24
1
vertical refresh rate
vertical refresh rate (Hz)
vertical refresh rate (hex)
25
1
horizontal refresh rate
horizontal refresh rate (kHz) (integer)
horizontal refresh rate (hex)
26
1
horizontal refresh rate
horizontal refresh rate (kHz) (decimal
fraction * 256)
horizontal refresh rate (hex)
27
1
signal format
28-31
4
Name
lamp runtime
Description
Content
0x01
separate (hex)
0x02
sync on green (hex)
0x03
TBD (reserved) (hex)
0x00
invalid (hex)
MSB (hex)
runtime in hours as DWORD
BYTE 1 (hex)
BYTE 2 (hex)
LSB (hex)
32-35
4
TBD
TBD (reserved) (hex)
TBD (reserved) (hex)
TBD (reserved) (hex)
TBD (reserved) (hex)
36
1
lamp status
37
1
TBD
38-41
4
projector runtime
0x00
lamp off (hex)
0x01
lamp on (hex)
TBD (reserved) (hex)
MSB (hex)
runtime in seconds as DWORD
BYTE 1 (hex)
BYTE 2 (hex)
LSB (hex)
42
43
44
45
1
1
1
1
projector status
rear projection mode
status
ceiling mode status
format (color space)
R5905745 COMMAND CATALOG 07/05/2015
0x00
Off (hex)
0x01
On (hex)
0x00
Off (hex)
0x01
On (hex)
0x00
Off (hex)
0x01
On (hex)
0x00
invalid (hex)
0x01
auto (hex)
0x02
RGB (hex)
0x03
YUV (hex)
19
3. Commands
3.5
get advanced control info, read
About this command
This command gets the "advanced control info" of the projector.
Request
Pos
Size
Name
0-2
3
get advanced control info
Description
Content
0x2A
0x05
0xA2
Response
Pos
Size
Name
0-2
3
get advanced control info
Description
Content
0x2A
0x05
0xA2
3
4
1
1
color temperature value
gain R
range 0->100
0x00
invalid (hex)
0x01
native (hex)
0x02
3200K (hex)
0x03
5400K (hex)
0x04
6500K (hex)
0x05
8800K (hex)
gain R (hex)
(OSD range 0->100)
5
1
gain G
range 0->100
gain G (hex)
(OSD range 0->100)
6
1
gain B
7
1
offset R
8
1
offset G
9
1
offset B
10
1
TBD
range 0->100
gain B (hex)
(OSD range 0->100)
range 0->100
offset R (hex)
(OSD range 0->100)
range 0->100
offset G (hex)
(OSD range 0->100)
range 0->100
offset B (hex)
(OSD range 0->100)
20
TBD (reserved) (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.6
get aspect ratio file, read
About this command
This command gets the aspect ratio file value.
Request
Pos
Size
Name
0
1
get adj
1
1
2
1
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
adj aspect ratio
0x0B
adj aspect ratio (hex)
aspect ratio file
0xC0
aspect ratio file (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
2
1
3
1
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
adj aspect ratio
0x0B
adj aspect ratio (hex)
aspect ratio file
0xC0
aspect ratio file (hex)
aspect ratio
0x00
invalid (hex)
0x01
4:3 (hex)
0x02
16:10 (hex)
0x03
native (hex)
0x04
auto (hex)
R5905745 COMMAND CATALOG 07/05/2015
21
3. Commands
3.7
get auto image adjust, read
About this command
This command gets the auto image adjust mode.
Request
Pos
Size
Name
0
1
get adj
1
1
adj auto image
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xa8
adj auto image (hex)
Response
22
Pos
Size
Name
0
1
get adj
1
1
2
1
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
adj auto image
0xa8
adj auto image (hex)
auto image adjust status
0x00
Off (hex)
0x01
always (hex)
0x02
auto (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.8
get auto power off, read
About this command
This command gets the auto power off mode.
Request
Pos
Size
Name
0
1
get adj
1
1
adj auto power off
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xA6
adj auto power off (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
adj auto power off
2
1
auto power off status
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xA6
adj auto power off (hex)
0x00
Off (hex)
0x01
On (hex)
23
3. Commands
3.9
get auto power on, read
About this command
This command gets the auto power on mode.
Request
Pos
Size
Name
0
1
get adj
1
1
adj auto power on
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xA7
adj auto power on (hex)
Response
24
Pos
Size
Name
0
1
get adj
1
1
adj auto power on
2
1
auto power on status
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xA7
adj auto power on (hex)
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.10 get auto source, read
About this command
This command gets the auto source status.
Request
Pos
Size
Name
0
1
get auto source
1
1
get auto source
Description
Content
0x91
get auto source (hex)
0x01
get auto source (hex)
Response
Pos
Size
Name
0
1
get auto source
0x91
get auto source (hex)
1
1
get auto source
0x01
get auto source (hex)
2
1
auto source status
R5905745 COMMAND CATALOG 07/05/2015
Description
Content
0x00
Off (hex)
0x01
On (hex)
25
3. Commands
3.11 get brightness, read
About this command
This command gets the brightness value of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj brightness
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x02
adj brightness (hex)
Response
26
Pos
Size
Name
0
1
get adj
1
1
adj brightness
2
1
brightness value
Description
byte value known as "get adj"
range 0->100
Content
0x21
get adj (hex)
0x02
adj brightness (hex)
brightness value (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.12 get ceiling mode, read
About this command
This command gets the ceiling mode.
Request
Pos
Size
Name
0
1
get adj
1
1
adj ceiling
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xA3
adj ceiling (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
adj ceiling
2
1
ceiling mode status
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xA3
adj ceiling (hex)
0x00
Off (hex)
0x01
On (hex)
27
3. Commands
3.13 get color temperature, read
About this command
This command sets the color temperature of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj color temperature
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x45
Response
28
Pos
Size
Name
Description
0
1
get adj
1
1
adj color temperature
0x45
2
1
color temperature value
0x00
invalid (hex)
0x01
native (hex)
0x02
3200K (hex)
0x03
5400K (hex)
byte value known as "get adj"
Content
0x21
get adj (hex)
0x04
6500K (hex)
0x05
8800K (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.14 get color wheel index, read
About this command
This command gets the color wheel index.
Request
Pos
Size
0
1
1
1
2
1
Name
Description
Content
get color wheel index
0x58
get color wheel index (hex)
get color wheel index
0x21
get color wheel index (hex)
get color wheel index
0x41
get color wheel index (hex)
Response
Pos
Size
Name
Description
0
1
get color wheel index
0x58
get color wheel index (hex)
1
1
get color wheel index
0x21
get color wheel index (hex)
2
1
get color wheel index
0x41
get color wheel index (hex)
3-4
2
color wheel index
Content
MSB (hex)
LSB (hex)
R5905745 COMMAND CATALOG 07/05/2015
29
3. Commands
3.15 get contrast, read
About this command
This command gets the contrast value of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj contrast
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x01
adj contrast (hex)
Response
30
Pos
Size
Name
0
1
get adj
1
1
adj contrast
2
1
contrast value
Description
byte value known as "get adj"
range 0->100
Content
0x21
get adj (hex)
0x01
adj contrast (hex)
contrast value (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.16 get diagnostics info, read
About this command
This command gets the "diagnostics" info of the projector.
Request
Pos
Size
0-2
3
Name
Description
get diagnostics info
Content
0x2A
0x07
0xA2
Response
Pos
Size
0-2
3
Name
get diagnostics info
Description
Content
0x2A
0x07
0xA2
3
1
error code
R5905745 COMMAND CATALOG 07/05/2015
0x00
lamp 1 failure (hex)
0x01
TBD (reserved) (hex)
0x02
TBD (reserved) (hex)
0x03
F-type fan error (hex)
0x04
R-type fan error (hex)
0x05
DDP442x not ready (hex)
0x06
TBD (reserved) (hex)
0x07
overtemperature (hex)
0x08
lamp 1 strike failure (hex)
0x09
TBD (reserved) (hex)
0x0A
TBD (reserved) (hex)
0x0B
color wheel error (hex)
0x0C
TBD (reserved) (hex)
0x0D
system standby (hex)
0x0E
system encoding (hex)
0x0F
system warm up (hex)
0x10
system normal operating
(hex)
31
3. Commands
3.17 get dimming, read
About this command
This command gets the dimming value.
Request
Pos
Size
Name
0
1
get adj
1
1
adj dimming
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x0D
adj dimming (hex)
Response
32
Pos
Size
Name
0
1
get adj
1
1
adj dimming
2
1
dimming value
Description
byte value known as "get adj"
lamp power (Watt)
Content
0x21
get adj (hex)
0x0D
adj dimming (hex)
0x00
276.4W (hex)
0x01
300W (hex)
0x02
321W (hex)
0x03
343.1W (hex)
0x04
360W (hex)
0x05
378W (hex)
0x06
400W (hex)
0x07
420W (hex)
0x08
442W (hex)
0x09
462W (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.18 get display mode, read
About this command
This command gets the display mode of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj display mode
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x15
adj display mode (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
2
1
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
adj display mode
0x15
adj display mode (hex)
display mode status
0x00
presentation (hex)
0x01
video (hex)
0x02
bright (hex)
R5905745 COMMAND CATALOG 07/05/2015
33
3. Commands
3.19 get format, read
About this command
This command gets the input format of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj input format
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x14
adj input format (hex)
Response
34
Pos
Size
Name
0
1
get adj
1
1
2
1
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
adj input format
0x14
adj input format (hex)
format (color space)
0x00
invalid (hex)
0x01
auto (hex)
0x02
RGB (hex)
0x03
YUV (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.20 get freeze, read
About this command
This command gets the freeze status.
Request
Pos
Size
Name
0
1
get adj
1
1
freeze
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xac
set freeze (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
freeze
2
1
freeze value
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xac
set freeze (hex)
0x00
off (hex)
0x01
on (hex)
35
3. Commands
3.21 get gamma, read
About this command
This command gets the gamma value.
Request
Pos
Size
Name
0
1
get adj
1
1
adj gamma
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x70
adj gamma (hex)
Response
36
Pos
Size
Name
0
1
get adj
1
1
2
1
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
adj gamma
0x70
adj gamma (hex)
gamma value
0x00
film (hex)
0x01
video (hex)
0x02
graphics (hex)
0x03
standard (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.22 get general info, read
About this command
This command gets the "general" info of the projector.
Request
Pos
Size
0-2
3
Name
Description
get general info
Content
0x2A
0x02
0xA2
Response
Pos
Size
0-2
3
Name
get general info
Description
Content
0x2A
0x02
0xA2
3
1
projector status
0x00
Off (hex)
0x01
On (hex)
4
1
TBD
TBD (reserved) (hex)
5
1
TBD
TBD (reserved) (hex)
6
1
main source
R5905745 COMMAND CATALOG 07/05/2015
0x00
HDMI (hex)
0x01
VGA (hex)
0x02
DVI (hex)
0x03
BNC (hex)
0x04
CVBS (hex)
0x1A
invalid (hex)
37
3. Commands
3.23 get geometry adjust info, read
About this command
This command gets the "geometry adjust info" of the projector.
Request
Pos
Size
Name
0-2
3
get geometry adjust info
Description
Content
0x2A
0x04
0xA2
Response
Pos
Size
Name
0-2
3
get geometry adjust info
Description
Content
0x2A
0x04
0xA2
3
1
TBD
4
1
keystone value
5
1
TBD
6
1
TBD
7
1
aspect ratio
TBD (reserved) (hex)
range 0->40
keystone value (hex)
(OSD range -20->20)
38
TBD (reserved) (hex)
TBD (reserved) (hex)
0x00
invalid (hex)
0x01
4:3 (hex)
0x02
16:10 (hex)
0x03
native (hex)
0x04
auto (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.24 get H start, read
About this command
This command gets the horizontal start pixel for the VGA and BNC inputs.
Request
Pos
Size
Name
0
1
get adj
1
1
get H start
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x11
get H start (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
get H start
2
1
H start value
Description
byte value known as "get adj"
range 0->100
Content
0x21
get adj (hex)
0x11
get H start (hex)
H start value (hex)
(OSD range 0->100)
R5905745 COMMAND CATALOG 07/05/2015
39
3. Commands
3.25 get high altitude, read
About this command
This command gets the high altitude setting.
Request
Pos
Size
0
1
1
1
Name
Description
Content
get high altitude
0x69
get high altitude (hex)
get high altitude
0x41
get high altitude (hex)
Response
40
Pos
Size
Name
Description
0
1
get high altitude
0x69
get high altitude (hex)
1
1
get high altitude
0x41
get high altitude (hex)
2
1
high altitude status
Content
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.26 get image setting info, read
About this command
This command gets the "image setting" info of the projector.
Request
Pos
Size
0-2
3
Name
Description
get image setting info
Content
0x2A
0x03
0xA2
Response
Pos
Size
0-2
3
Name
Description
get image setting info
Content
0x2A
0x03
0xA2
3
1
contrast value
range 0->100
contrast value (hex)
4
1
brightness value
range 0->100
brightness value (hex)
5
1
saturation value
range 0->100
saturation value (hex)
6
1
tint value
range 0->100
tint value (hex)
7
1
sharpness value
range 0->14
sharpness value (hex)
8
1
TBD
9
1
gamma value
(OSD range -7->+7)
R5905745 COMMAND CATALOG 07/05/2015
TBD (reserved) (hex)
0x00
film (hex)
0x01
video (hex)
0x02
graphics (hex)
0x03
standard (hex)
41
3. Commands
3.27 get input black balance, read
About this command
This command gets the input black balance value of the active source. This is applicable for the specified color.
Request
Pos
Size
Name
0
1
get adj
1
1
adj input black balance
2
1
color
Description
byte value known as "get adj"
color specification
Content
0x21
get adj (hex)
0x6E
adj inp black balance (hex)
0x00
red (hex)
0x01
green (hex)
0x02
blue (hex)
0x21
get adj (hex)
0x6E
adj inp black balance (hex)
0x00
red (hex)
0x01
green (hex)
0x02
blue (hex)
Response
Pos
Size
0
1
get adj
1
1
adj input black balance
2
1
color
3
1
Name
balance value
Description
byte value known as "get adj"
color specification
range 0->100
Content
balance value (hex)
(OSD range 0->100)
42
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.28 get input selection, read
About this command
This command gets the input of the projector.
Request
Pos
Size
0
1
Name
Description
read input selection
Content
0x34
read input selection (hex)
Response
Pos
Size
0
1
read input selection
Name
0x34
read input selection (hex)
1
1
input slot
0x00
HDMI (hex)
0x01
VGA (hex)
0x02
DVI (hex)
0x03
BNC (hex)
0x04
CVBS (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
Content
43
3. Commands
3.29 get input white balance, read
About this command
This command gets the input white balance value of the active source. This is applicable for the specified color.
Request
Pos
Size
Name
0
1
get adj
1
1
adj input white balance
2
1
color
Description
byte value known as "get adj"
color specification
Content
0x21
get adj (hex)
0x6F
adj input white balance (hex)
0x00
red (hex)
0x01
green (hex)
0x02
blue (hex)
0x21
get adj (hex)
0x6F
adj input white balance (hex)
0x00
red (hex)
0x01
green (hex)
0x02
blue (hex)
Response
Pos
Size
0
1
get adj
1
1
adj input white balance
2
1
color
3
1
Name
balance value
Description
byte value known as "get adj"
color specification
range 0->100
Content
balance value (hex)
(OSD range 0->100)
44
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.30 get internal pattern, read
About this command
This command gets the internal pattern.
Request
Pos
Size
0
1
Name
Description
get internal pattern
Content
0x42
get internal pattern (hex)
Response
Pos
Size
0
1
get internal pattern
Name
0x42
get internal pattern (hex)
1
1
internal pattern number
0x00
none (hex)
0x01
white (hex)
0x02
grid (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
Content
45
3. Commands
3.31 get IP configuration info, read
About this command
This command gets the "IP configuration info" of the projector.
Request
Pos
Size
0-2
3
Name
Description
get IP configuration info
Content
0x2A
0x06
0xA2
Response
Pos
Size
Name
0-2
3
get IP configuration info
Description
Content
0x2A
0x06
0xA2
3-6
4
IP address
first octet (hex)
second octet (hex)
third octet (hex)
fourth octet (hex)
7-10
4
subnet mask
first octet (hex)
second octet (hex)
third octet (hex)
fourth octet (hex)
11-14
4
first octet (hex)
default gateway
second octet (hex)
third octet (hex)
fourth octet (hex)
15
16-21
1
6
DHCP
LAN FW version
0x00
Off (hex)
0x01
On (hex)
BYTE1 (hex)
BYTE2 (hex)
BYTE3 (hex)
BYTE4 (hex)
BYTE5 (hex)
BYTE6 (hex)
22-27
6
MAC address
first octet (hex)
second octet (hex)
third octet (hex)
fourth octet (hex)
fifth octet (hex)
sixth octet (hex)
46
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.32 get lamp max runtime, read
About this command
This command gets the maximum runtime of the lamp.
Request
Pos
Size
0
1
1
1
2
1
Name
Description
Content
lamp
0x76
lamp (hex)
get lamp max runtime
0x89
get lamp max runtime (hex)
lamp number
0x01
lamp 1 (hex)
0x02
lamp 2 (hex)
0x03
lamp 3 (hex)
0x04
lamp 4 (hex)
Response
Pos
Size
0
1
lamp
0x76
lamp (hex)
1
1
get lamp max runtime
0x89
get lamp max runtime (hex)
2
1
lamp number
0x01
lamp 1 (hex)
0x02
lamp 2 (hex)
0x03
lamp 3 (hex)
0x04
lamp 4 (hex)
3-6
4
Name
lamp max runtime
Description
maximum runtime in hours as DWORD
Content
MSB (hex)
BYTE 1 (hex)
BYTE 2 (hex)
LSB (hex)
R5905745 COMMAND CATALOG 07/05/2015
47
3. Commands
3.33 get lamp on, read
About this command
This command gets the status of the lamp.
Request
Pos
Size
0
1
1
1
2
1
Name
Description
Content
lamp
0x76
lamp (hex)
get lamp on
0x9A
get lamp on (hex)
lamp number
0x01
lamp 1 (hex)
0x02
lamp 2 (hex)
0x03
lamp 3 (hex)
0x04
lamp 4 (hex)
Response
Pos
Size
0
1
lamp
0x76
lamp (hex)
1
1
get lamp on
0x9A
get lamp on (hex)
2
1
lamp number
0x01
lamp 1 (hex)
0x02
lamp 2 (hex)
0x03
lamp 3 (hex)
0x04
lamp 4 (hex)
0x00
lamp off (hex)
0x01
lamp on (hex)
3
48
1
Name
lamp status
Description
Content
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.34 get lamp runtime, read
About this command
This command gets the runtime of the lamp.
Request
Pos
Size
0
1
1
1
2
1
Name
Description
Content
lamp
0x76
lamp (hex)
get lamp runtime
0x90
get lamp runtime (hex)
lamp number
0x01
lamp 1 (hex)
0x02
lamp 2 (hex)
0x03
lamp 3 (hex)
0x04
lamp 4 (hex)
Response
Pos
Size
0
1
lamp
0x76
lamp (hex)
1
1
get lamp runtime
0x90
get lamp runtime (hex)
2
1
lamp number
0x01
lamp 1 (hex)
0x02
lamp 2 (hex)
0x03
lamp 3 (hex)
0x04
lamp 4 (hex)
3-6
4
Name
lamp runtime
Description
runtime in hours as DWORD
Content
MSB (hex)
BYTE 1 (hex)
BYTE 2 (hex)
LSB (hex)
R5905745 COMMAND CATALOG 07/05/2015
49
3. Commands
3.35 get lamp status, read
About this command
This command gets the status of the lamp(s).
Request
Pos
Size
0
1
1
1
Name
Description
Content
get lamp status
0x67
get lamp status (hex)
get lamp status
0x40
get lamp status (hex)
Response
50
Pos
Size
Name
Description
0
1
get lamp status
0x67
get lamp status (hex)
1
1
get lamp status
0x40
get lamp status (hex)
2
1
lamp status
Content
0x00
lamp(s) off (hex)
0x01
lamp(s) on (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.36 get language, read
About this command
This command gets the language.
Request
Pos
Size
0-1
2
Name
Description
get language
Content
0x52
0x01
Response
Pos
Size
0-1
2
Name
get language
Description
Content
0x52
0x01
2
1
language values
R5905745 COMMAND CATALOG 07/05/2015
0x00
English (hex)
0x01
French (hex)
0x02
Spanish (hex)
0x03
German (hex)
0x04
Simplified Chinese (hex)
0x05
Japanese (hex)
0x06
Russian (hex)
0x07
Korean (hex)
0x08
Turkish (hex)
51
3. Commands
3.37 get main zoom, read
About this command
This command gets the main zoom in/out.
Request
Pos
Size
0
1
1
1
Name
Description
Content
get main zoom
0xA1
get main zoom (hex)
get main zoom
0x00
get main zoom (hex)
Response
Pos
Size
Name
Description
0
1
get main zoom
0xA1
get main zoom (hex)
1
1
get main zoom
0x00
get main zoom (hex)
2
1
main zoom value
range 0->70
Content
main zoom value (hex)
(OSD range -20->+10)
52
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.38 get menu position, read
About this command
This command gets the menu position.
Request
Pos
Size
0
1
1
1
Name
Description
Content
get menu position
0x91
get menu position (hex)
get menu position
0x02
get menu position (hex)
Response
Pos
Size
Name
0
1
get menu position
0x91
get menu position (hex)
1
1
get menu position
0x02
get menu position (hex)
2
1
menu position value
0x00
top left (hex)
0x01
top right (hex)
0x02
center (hex)
0x03
bottom left (hex)
0x04
bottom right (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
Content
53
3. Commands
3.39 get no signal color logo, read
About this command
This command gets the blanking color value and logo status, used when no signal is connected.
Request
Pos
Size
Name
0
1
get adj
1
1
adj no signal color
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x7B
adj no signal color (hex)
Response
54
Pos
Size
Name
0
1
get adj
1
1
adj no signal color
2
1
value
Description
byte value known as "get adj"
background color value
Content
0x21
get adj (hex)
0x7B
adj no signal color (hex)
0x01
logo (hex)
0x02
blue (hex)
0x03
black (hex)
0x04
white (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.40 get noise reduction, read
About this command
This command gets the noise reduction value of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj noise reduction
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x73
adj noise reduction (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
adj noise reduction
2
1
noise reduction value
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "get adj"
range 0->32
Content
0x21
get adj (hex)
0x73
adj noise reduction (hex)
noise reduction value (hex)
55
3. Commands
3.41 get phase, read
About this command
This command gets the phase value of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj phase
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x06
adj phase (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
adj phase
2
1
phase value
Description
byte value known as "get adj"
range 0->63
Content
0x21
get adj (hex)
0x06
adj phase (hex)
phase value (hex)
(OSD range 0->63)
56
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.42 get PIP enable, read
About this command
This command gets the "enable PIP" value.
Request
Pos
Size
0
1
1
1
Name
Description
Content
get PIP enable
0xA1
get PIP enable (hex)
get PIP enable
0x01
get PIP enable (hex)
Response
Pos
Size
Name
0
1
get PIP enable
0xA1
get PIP enable (hex)
1
1
get PIP enable
0x01
get PIP enable (hex)
2
1
PIP enable value
R5905745 COMMAND CATALOG 07/05/2015
Description
Content
0x00
Off (hex)
0x01
On (hex)
57
3. Commands
3.43 get PIP position, write
About this command
This command gets the PIP position.
Request
Pos
Size
0
1
1
1
Name
Description
Content
get PIP position
0xA1
get PIP position (hex)
get PIP position
0x04
get PIP position (hex)
Response
58
Pos
Size
Name
Description
0
1
get PIP position
0xA1
get PIP position (hex)
1
1
get PIP position
0x04
get PIP position (hex)
2
1
PIP position value
0x00
top left (hex)
0x01
top right (hex)
0x02
bottom left (hex)
0x03
bottom right (hex)
Content
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.44 get PIP select, read
About this command
This command gets the PIP select value.
Request
Pos
Size
0
1
1
1
Name
Description
Content
get PIP select
0xA1
get PIP select (hex)
get PIP select
0x02
get PIP select (hex)
Response
Pos
Size
Name
0
1
get PIP select
0xA1
get PIP select (hex)
1
1
get PIP select
0x02
get PIP select (hex)
2
1
PIP select value
0x00
HDMI (hex)
0x01
VGA (hex)
0x02
DVI (hex)
0x03
BNC (hex)
0x04
CVBS (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
Content
59
3. Commands
3.45 get PIP size, read
About this command
This command gets the PIP size.
Request
Pos
Size
0
1
1
1
Name
Description
Content
get PIP size
0xA1
get PIP size (hex)
get PIP size
0x03
get PIP size (hex)
Response
60
Pos
Size
Name
Description
0
1
get PIP size
0xA1
get PIP size (hex)
1
1
get PIP size
0x03
get PIP size (hex)
2
1
PIP size value
0x00
Small (hex)
0x01
Medium (hex)
0x02
Large (hex)
Content
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.46 get rear projection mode, read
About this command
This command gets the rear projection mode.
Request
Pos
Size
Name
0
1
get adj
1
1
adj rear
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xA2
adj rear (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
adj rear
2
1
rear projection mode
status
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0xA2
adj rear (hex)
0x00
Off (hex)
0x01
On (hex)
61
3. Commands
3.47 get resolution, read
About this command
This command gets the resolution.
Request
Pos
Size
0
1
1
1
Name
Description
Content
get resolution
0xF0
get resolution (hex)
get resolution
0x01
get resolution (hex)
Response
Pos
Size
Name
Description
0
1
get resolution
0xF0
get resolution (hex)
1
1
get resolution
0x01
get resolution (hex)
2-5
4
resolution value
Content
Resolution can be calculated from the
4 bytes:
X-resolution = BYTE1 * 256 + BYTE2
Y-resolution = BYTE3 * 256 + BYTE4
62
BYTE 1 (hex)
BYTE 2 (hex)
BYTE 3 (hex)
BYTE 4 (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.48 get saturation, read
About this command
This command gets the saturation value of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj saturation
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x03
adj saturation (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
adj saturation
2
1
saturation value
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "get adj"
range 0->100
Content
0x21
get adj (hex)
0x03
adj saturation (hex)
saturation value (hex)
63
3. Commands
3.49 get serial number, read
About this command
This command gets the serial number of the projector.
Request
Pos
Size
0-2
3
Name
Description
get serial number
Content
0x2A
0x08
0xA2
Response
Pos
Size
0-2
3
Name
get serial number
Description
Content
0x2A
0x08
0xA2
3-12
10
serial number
BYTE1 (hex)
BYTE2 (hex)
BYTE3 (hex)
BYTE4 (hex)
BYTE5 (hex)
BYTE6 (hex)
BYTE7 (hex)
BYTE8 (hex)
BYTE9 (hex)
BYTE10 (hex)
64
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.50 get sharpness, read
About this command
This command gets the sharpness value of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj sharpness
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x05
adj sharpness (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
adj sharpness
2
1
sharpness value
Description
byte value known as "get adj"
range 0->14
Content
0x21
get adj (hex)
0x05
adj sharpness (hex)
sharpness value (hex)
(OSD range -7->+7)
R5905745 COMMAND CATALOG 07/05/2015
65
3. Commands
3.51 get tint, read
About this command
This command gets the tint value of the active source.
Request
Pos
Size
Name
0
1
get adj
1
1
adj tint
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x04
adj tint (hex)
Response
66
Pos
Size
Name
0
1
get adj
1
1
adj tint
2
1
tint value
Description
byte value known as "get adj"
range 0->100
Content
0x21
get adj (hex)
0x04
adj tint (hex)
tint value (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.52 get V start, read
About this command
This command gets the vertical start pixel for the VGA and BNC inputs.
Request
Pos
Size
Name
0
1
get adj
1
1
get V start
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
0x12
get V start (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
get V start
2
1
V start value
Description
byte value known as "get adj"
range 0->20
Content
0x21
get adj (hex)
0x12
get V start (hex)
V start value (hex)
(OSD range -10->10)
R5905745 COMMAND CATALOG 07/05/2015
67
3. Commands
3.53 get versions, read
About this command
This command is used to get the version(s).
Request
Pos
Size
0
1
1
1
2
1
Name
Description
Content
get versions
0x60
get versions (hex)
from data index
0x00
PW392 (hex)
0x06
DDP442x (hex)
0x0C
PIC (hex)
0x12
Lan Module (hex)
0x18
Waveform (hex)
0x1E
EDID (hex)
0x00
PW392 (hex)
0x01
DDP442x (hex)
0x08
PIC (hex)
0x0C
Lan module (hex)
to data index
0x10
Waveform (hex)
0x14
EDID (hex)
Response
Pos
Size
0
1
get versions
0x60
get versions (hex)
1
1
from data index
0x00
PW392 (hex)
0x06
DDP442x (hex)
0x0C
PIC (hex)
0x12
Lan Module (hex)
0x18
Waveform (hex)
0x1E
EDID (hex)
0x00
PW392 (hex)
0x01
DDP442x (hex)
0x08
PIC (hex)
0x0C
Lan module (hex)
2
3-8
1
6
Name
Description
to data index
version
Content
0x10
Waveform (hex)
0x14
EDID (hex)
Each version consists of 6 bytes:
major version (MSB) (hex)
- Byte 0-1: major version number
major version (LSB) (hex)
- Byte 2-3: build number
build number (MSB) (hex)
- Byte 4-5: build number
build number (hex)
build number (hex)
build number (LSB) (hex)
68
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.54 get warp keystone vertical, read
About this command
This command gets the warp keystone vertical value.
Request
Pos
Size
Name
0
1
get adj
1
1
2
1
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
adj warp
0xA1
adj warp (hex)
warp keystone vertical
0x01
warp keystone vertical (hex)
Response
Pos
Size
Name
0
1
get adj
1
1
2
1
3
1
keystone value
Description
byte value known as "get adj"
Content
0x21
get adj (hex)
adj warp
0xA1
adj warp (hex)
warp keystone vertical
0x01
warp keystone vertical (hex)
range 0->40
keystone value (hex)
(OSD range -20->20)
R5905745 COMMAND CATALOG 07/05/2015
69
3. Commands
3.55 increment noise reduction, write
About this command
This command increments the noise reduction by one.
Request
70
Pos
Size
0
1
inc adj
Name
1
1
adj noise reduction
Description
byte value known as "inc adj"
Content
0x22
inc adj (hex)
0x73
adj noise reduction (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.56 reset settings to factory defaults, write
About this command
This command resets the settings to factory defaults.
Request
Pos
Size
0
1
Name
factory defaults
R5905745 COMMAND CATALOG 07/05/2015
Description
Content
0x31
factory defaults (hex)
71
3. Commands
3.57 set aspect ratio file, write
About this command
This command sets the aspect ratio file value.
Request
72
Pos
Size
Name
0
1
set adj
1
1
2
3
Description
byte value known as "set adj"
Content
0x20
set adj (hex)
adj aspect ratio
0x0B
adj aspect ratio (hex)
1
aspect ratio file
0xC0
aspect ratio file (hex)
1
aspect ratio
0x00
invalid (hex)
0x01
4:3 (hex)
0x02
16:10 (hex)
0x03
native (hex)
0x04
auto (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.58 set auto image adjust, write
About this command
This command sets the auto image adjust mode.
Request
Pos
Size
Name
0
1
set adj
1
1
2
1
Description
set adj (hex)
adj auto image
0xA8
adj auto image (hex)
auto image adjust status
0x00
Off (hex)
0x01
always (hex)
0x02
auto (hex)
R5905745 COMMAND CATALOG 07/05/2015
byte value known as "set adj"
Content
0x20
73
3. Commands
3.59 set auto power off, write
About this command
This command sets the auto power off mode.
Request
74
Pos
Size
Name
0
1
set adj
1
1
2
1
Description
byte value known as "set adj"
Content
0x20
set adj (hex)
adj auto power off
0xA6
adj auto power off (hex)
auto power off status
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.60 set auto power on, write
About this command
This command sets the auto power on mode.
Request
Pos
Size
Name
0
1
set adj
1
1
2
1
Description
set adj (hex)
adj auto power on
0xA7
adj auto power on (hex)
auto power on status
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
byte value known as "set adj"
Content
0x20
75
3. Commands
3.61 set auto source, write
About this command
This command sets the auto source status.
Request
76
Pos
Size
0
1
set auto source
Name
Description
0x90
set auto source (hex)
Content
1
1
set auto source
0x01
set auto source (hex)
2
1
auto source status
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.62 set brightness, write
About this command
This command sets the brightness value of the active source.
Request
Pos
Size
Name
0
1
set adj
1
1
adj brightness
2
1
brightness value
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "set adj"
range 0->100
Content
0x20
set adj (hex)
0x02
adj brightness (hex)
brightness value (hex)
77
3. Commands
3.63 set ceiling mode, write
About this command
This command sets the ceiling mode.
Request
78
Pos
Size
Name
0
1
set adj
1
1
2
1
Description
byte value known as "set adj"
Content
0x20
set adj (hex)
adj ceiling
0xA3
adj ceiling (hex)
ceiling mode status
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.64 set color temperature, write
About this command
This command sets the color temperature of the active source.
Request
Pos
Size
Name
0
1
set adj
1
1
adj color temperature
0x45
2
1
color temperature value
0x00
invalid (hex)
0x01
native (hex)
0x02
3200K (hex)
0x03
5400K (hex)
0x04
6500K (hex)
0x05
8800K (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "set adj"
Content
0x20
set adj (hex)
79
3. Commands
3.65 set color wheel index, write
About this command
This command sets the color wheel index.
Request
Pos
Size
0
1
set color wheel index
Name
Description
0x58
set color wheel index (hex)
Content
1
1
set color wheel index
0x20
set color wheel index (hex)
2
1
set color wheel index
0x41
set color wheel index (hex)
3-4
2
color wheel index
MSB (hex)
LSB (hex)
80
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.66 set contrast, write
About this command
This command sets the contrast value of the active source.
Request
Pos
Size
0
1
set adj
Name
1
1
adj contrast
2
1
contrast value
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "set adj"
range 0->100
Content
0x20
set adj (hex)
0x01
adj contrast (hex)
contrast value (hex)
81
3. Commands
3.67 set dimming, write
About this command
This command sets the dimming value.
Request
82
Pos
Size
Name
0
1
set adj
1
1
adj dimming
2
1
dimming value
Description
byte value known as "set adj"
lamp power (Watt)
Content
0x20
set adj (hex)
0x0D
adj dimming (hex)
0x00
276.4W (hex)
0x01
300W (hex)
0x02
321W (hex)
0x03
343.1W (hex)
0x04
360W (hex)
0x05
378W (hex)
0x06
400W (hex)
0x07
420W (hex)
0x08
442W (hex)
0x09
462W (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.68 set display mode, write
About this command
This command sets the display mode of the active source.
Request
Pos
Size
Name
0
1
set adj
1
1
2
1
Description
set adj (hex)
adj display mode
0x15
adj display mode (hex)
display mode status
0x00
presentation (hex)
0x01
video (hex)
0x02
bright (hex)
R5905745 COMMAND CATALOG 07/05/2015
byte value known as "set adj"
Content
0x20
83
3. Commands
3.69 set format, write
About this command
This command sets the input format of the active source.
Request
84
Pos
Size
0
1
set adj
Name
1
1
2
1
Description
byte value known as "set adj"
Content
0x20
set adj (hex)
adj input format
0x14
adj input format (hex)
format (color space)
0x00
invalid (hex)
0x01
auto (hex)
0x02
RGB (hex)
0x03
YUV (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.70 set freeze, write
About this command
This command sets the freeze status.
Request
Pos
Size
0
1
set adj
Name
1
1
freeze
2
1
freeze value
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "set adj"
Content
0x20
set adj (hex)
0xac
set freeze (hex)
0x00
off (hex)
0x01
on (hex)
85
3. Commands
3.71 set gamma, write
About this command
This command sets the gamma value.
Request
86
Pos
Size
Name
0
1
set adj
1
1
2
1
Description
byte value known as "set adj"
Content
0x20
set adj (hex)
adj gamma
0x70
adj gamma (hex)
gamma value
0x00
film (hex)
0x01
video (hex)
0x02
graphics (hex)
0x03
standard (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.72 set H start, write
About this command
This command sets the horizontal start pixel for the VGA and BNC inputs.
Request
Pos
Size
0
1
set adj
Name
1
1
set H start
2
1
H start value
Description
byte value known as "set adj"
range 0->100
Content
0x20
set adj (hex)
0x11
set H start (hex)
H start value (hex)
(OSD range 0->100)
R5905745 COMMAND CATALOG 07/05/2015
87
3. Commands
3.73 set high altitude, write
About this command
This command sets the high altitude setting.
Request
88
Pos
Size
0
1
1
1
2
1
Name
Description
Content
set high altitude
0x69
set high altitude (hex)
set high altitude
0x40
set high altitude (hex)
high altitude status
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.74 set input black balance, write
About this command
This command sets the input black balance value of the active source. This is applicable for the specified color.
Request
Pos
Size
0
1
set adj
1
1
adj input black balance
2
1
color
3
1
Name
balance value
Description
byte value known as "set adj"
color specification
range 0->100
Content
0x20
set adj (hex)
0x6E
adj inp black balance (hex)
0x00
red (hex)
0x01
green (hex)
0x02
blue (hex)
balance value (hex)
(OSD range 0->100)
R5905745 COMMAND CATALOG 07/05/2015
89
3. Commands
3.75 set input selection, write
About this command
This command sets the input of the projector.
Request
90
Pos
Size
0
1
1
1
Name
Description
Content
write input selection
0x33
write input selection (hex)
input slot
0x00
HDMI (hex)
0x01
VGA (hex)
0x02
DVI (hex)
0x03
BNC (hex)
0x04
CVBS (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.76 set input white balance, write
About this command
This command sets the input white balance value of the active source. This is applicable for the specified color.
Request
Pos
Size
0
1
set adj
1
1
adj input white balance
2
1
color
3
1
Name
balance value
Description
byte value known as "set adj"
color specification
range 0->100
Content
0x20
set adj (hex)
0x6F
adj input white balance (hex)
0x00
red (hex)
0x01
green (hex)
0x02
blue (hex)
balance value (hex)
(OSD range 0->100)
R5905745 COMMAND CATALOG 07/05/2015
91
3. Commands
3.77 set internal pattern, write
About this command
This command sets the internal pattern.
Request
92
Pos
Size
0
1
1
1
Name
Description
Content
set internal pattern
0x41
set internal pattern (hex)
internal pattern number
0x00
none (hex)
0x01
white (hex)
0x02
grid (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.78 set language, write
About this command
This command sets the language.
Request
Pos
Size
0-1
2
Name
set language
Description
Content
0x52
0x00
2
1
language values
R5905745 COMMAND CATALOG 07/05/2015
0x00
English (hex)
0x01
French (hex)
0x02
Spanish (hex)
0x03
German (hex)
0x04
Simplified Chinese (hex)
0x05
Japanese (hex)
0x06
Russian (hex)
0x07
Korean (hex)
0x08
Turkish (hex)
93
3. Commands
3.79 set lens center, write
About this command
This command sets the lens to the center.
Request
94
Pos
Size
0
1
lens
Name
Description
0xF4
lens (hex)
Content
1
1
set lens center
0x88
set lens center (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.80 set lens focus, write
About this command
This command sets the lens focus.
Request
Pos
Size
0
1
lens
Name
0xF4
lens (hex)
1
1
set lens focus
0x83
set lens focus (hex)
2
1
lens focus value
0x00
focus out (hex)
0x01
focus in (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
focus direction
Content
95
3. Commands
3.81 set lens shift, write
About this command
This command sets the lens shift.
Request
96
Pos
Size
0
1
lens
Name
Description
0xF4
lens (hex)
1
1
set lens shift
0x81
set lens shift (hex)
2
1
lens shift value
0x00
shift up (hex)
0x01
shift down (hex)
0x02
shift left (hex)
0x03
shift right (hex)
shift direction
Content
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.82 set lens zoom, write
About this command
This command sets the lens zoom.
Request
Pos
Size
0
1
lens
Name
0xF4
lens (hex)
1
1
set lens zoom
0x82
set lens zoom (hex)
2
1
lens zoom value
0x00
zoom in (hex)
0x01
zoom out (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
zoom direction
Content
97
3. Commands
3.83 set main zoom, write
About this command
This command sets the main zoom in/out.
Request
Pos
Size
0
1
set main zoom
Name
Description
0xA0
set main zoom (hex)
1
1
set main zoom
0x00
set main zoom (hex)
2
1
main zoom value
range 0->70
Content
main zoom value (hex)
(OSD range -20->+10)
98
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.84 set menu position, write
About this command
This command sets the menu position.
Request
Pos
Size
0
1
1
1
2
1
Name
Description
Content
set menu position
0x90
set menu position (hex)
set menu position
0x02
set menu position (hex)
menu position value
0x00
top left (hex)
0x01
top right (hex)
0x02
center (hex)
0x03
bottom left (hex)
0x04
bottom right (hex)
R5905745 COMMAND CATALOG 07/05/2015
99
3. Commands
3.85 set no signal color logo, write
About this command
This command sets the blanking color value and logo status, used when no signal is connected.
Request
100
Pos
Size
Name
0
1
set adj
1
1
2
1
Description
byte value known as "set adj"
Content
0x20
set adj (hex)
adj no signal color
0x7B
adj no signal color (hex)
background color
0x01
logo (hex)
0x02
blue (hex)
0x03
black (hex)
0x04
white (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.86 set noise reduction, write
About this command
This command sets the noise reduction value of the active source.
Request
Pos
Size
0
1
set adj
Name
1
1
adj noise reduction
2
1
noise reduction value
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "set adj"
range 0->32
Content
0x20
set adj (hex)
0x73
adj noise reduction (hex)
noise reduction value (hex)
101
3. Commands
3.87 set phase, write
About this command
This command sets the phase value of the active source.
Request
Pos
Size
Name
0
1
set adj
1
1
adj phase
2
1
phase value
Description
byte value known as "set adj"
range 0->63
Content
0x20
set adj (hex)
0x06
adj phase (hex)
phase value (hex)
(OSD range 0->63)
102
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.88 set PIP enable, write
About this command
This command sets the "enable PIP" value.
Request
Pos
Size
0
1
set PIP enable
Name
0xA0
set PIP enable (hex)
1
1
set PIP enable
0x01
set PIP enable (hex)
2
1
PIP enable value
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
Content
103
3. Commands
3.89 set PIP position, write
About this command
This command sets the PIP position.
Request
104
Pos
Size
0
1
1
1
2
1
Name
Description
Content
set PIP position
0xA0
set PIP position (hex)
set PIP position
0x04
set PIP position (hex)
PIP position value
0x00
top left (hex)
0x01
top right (hex)
0x02
bottom left (hex)
0x03
bottom right (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.90 set PIP select, write
About this command
This command sets the PIP select value.
Request
Pos
Size
0
1
set PIP select
Name
0xA0
set PIP select (hex)
1
1
set PIP select
0x02
set PIP select (hex)
2
1
PIP select value
0x00
HDMI (hex)
0x01
VGA (hex)
0x02
DVI (hex)
0x03
BNC (hex)
0x04
CVBS (hex)
R5905745 COMMAND CATALOG 07/05/2015
Description
Content
105
3. Commands
3.91 set PIP size, write
About this command
This command sets the PIP size.
Request
106
Pos
Size
0
1
set PIP size
Name
Description
0xA0
set PIP size (hex)
Content
1
1
set PIP size
0x03
set PIP size (hex)
2
1
PIP size value
0x00
Small (hex)
0x01
Medium (hex)
0x02
Large (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.92 set projector power on/off, write
About this command
This commands sets the projector on/off.
Request
Pos
Size
0
1
1
1
Name
Description
Content
set projector power
0x58
set projector power (hex)
power status
0x00
Off (hex)
0x03
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
107
3. Commands
3.93 set rear projection mode, write
About this command
This command sets the rear projection mode.
Request
108
Pos
Size
Name
0
1
set adj
1
1
2
1
Description
byte value known as "set adj"
Content
0x20
set adj (hex)
adj rear
0xA2
adj rear (hex)
rear projection mode
status
0x00
Off (hex)
0x01
On (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.94 set saturation, write
About this command
This command sets the saturation value of the active source.
Request
Pos
Size
0
1
set adj
Name
1
1
adj saturation
2
1
saturation value
R5905745 COMMAND CATALOG 07/05/2015
Description
byte value known as "set adj"
range 0->100
Content
0x20
set adj (hex)
0x03
adj saturation (hex)
saturation value (hex)
109
3. Commands
3.95 set sharpness, write
About this command
This command sets the sharpness value of the active source.
Request
Pos
Size
Name
0
1
set adj
1
1
adj sharpness
2
1
sharpness value
Description
byte value known as "set adj"
range 0->14
Content
0x20
set adj (hex)
0x05
adj sharpness (hex)
sharpness value (hex)
(OSD range -7->+7)
110
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.96 set TCP/IP, write
About this command
This command sets the TCP/IP settings of the projector.
Request
Pos
Size
0-2
3
Name
set TCP/IP
Description
Content
0x2A
0x01
0xA3
3-6
4
IP address
first octet (hex)
second octet (hex)
third octet (hex)
fourth octet (hex)
7-10
4
subnet mask
first octet (hex)
second octet (hex)
third octet (hex)
fourth octet (hex)
11-14
4
default gateway
first octet (hex)
second octet (hex)
third octet (hex)
fourth octet (hex)
15
1
DHCP
R5905745 COMMAND CATALOG 07/05/2015
0x00
Off (hex)
0x01
On (hex)
111
3. Commands
3.97 set tint, write
About this command
This command sets the tint value of the active source.
Request
112
Pos
Size
0
1
set adj
Name
1
1
adj tint
2
1
tint value
Description
byte value known as "set adj"
range 0->100
Content
0x20
set adj (hex)
0x04
adj tint (hex)
tint value (hex)
R5905745 COMMAND CATALOG 07/05/2015
3. Commands
3.98 set V start, write
About this command
This command sets the vertical start pixel for the VGA and BNC inputs.
Request
Pos
Size
0
1
set adj
Name
1
1
set V start
2
1
V start value
Description
byte value known as "set adj"
range 0->20
Content
0x20
set adj (hex)
0x12
set V start (hex)
V start value (hex)
(OSD range -10->10)
R5905745 COMMAND CATALOG 07/05/2015
113
3. Commands
3.99 set warp keystone vertical, write
About this command
This command sets the warp keystone vertical value.
Request
Pos
Size
0
1
set adj
1
1
2-3
2
4
1
Name
Description
set adj (hex)
adj warp
0xA1
adj warp (hex)
warp keystone vertical
0x01
warp keystone vertical (hex)
0x00
warp keystone vertical (hex)
keystone value
byte value known as "set adj"
Content
0x20
range 0->40
keystone value (hex)
(OSD range -20->20)
114
R5905745 COMMAND CATALOG 07/05/2015
Index
INDEX
A
About this document
AV mute 15–16
read 15
write 16
4
B
Barco Projection Protocol
5–6
C
Command representation
12
D
decrement noise reduction
write 17
17
E
Ethernet
9
G
get about info 18
read 18
get advanced control info 20
read 20
get aspect ratio file 21
read 21
get auto image adjust 22
read 22
get auto power off 23
read 23
get auto power on 24
read 24
get auto source 25
read 25
get brightness 26
read 26
get ceiling mode 27
read 27
get color temperature 28
read 28
get color wheel index 29
read 29
get contrast 30
read 30
get diagnostics info 31
read 31
get dimming 32
read 32
get display mode 33
read 33
get format 34
read 34
get freeze 35
read 35
get gamma 36
read 36
get general info 37
read 37
get geometry adjust info 38
read 38
get H start 39
read 39
get high altitude 40
read 40
get image setting info 41
read 41
R5905745 COMMAND CATALOG 07/05/2015
get input black balance 42
read 42
get input selection 43
read 43
get input white balance 44
read 44
get internal pattern 45
read 45
get IP configuration info 46
read 46
get lamp max runtime 47
read 47
get lamp on 48
read 48
get lamp runtime 49
read 49
get lamp status 50
read 50
get language 51
read 51
get main zoom 52
read 52
get menu position 53
read 53
get no signal color logo 54
read 54
get noise reduction 55
read 55
get phase 56
read 56
get PIP enable 57
read 57
get PIP position 58
write 58
get PIP select 59
read 59
get PIP size 60
read 60
get rear projection mode 61
read 61
get resolution 62
read 62
get saturation 63
read 63
get serial number 64
read 64
get sharpness 65
read 65
get tint 66
read 66
get V start 67
read 67
get versions 68
read 68
get warp keystone vertical 69
read 69
I
increment noise reduction
write 70
Introduction 3
70
P
Projection Protocol
Protocol 5–6
5–6
R
read 15, 18, 20–57, 59–69
AV mute 15
115
Index
get about info 18
get advanced control info 20
get aspect ratio file 21
get auto image adjust 22
get auto power off 23
get auto power on 24
get auto source 25
get brightness 26
get ceiling mode 27
get color temperature 28
get color wheel index 29
get contrast 30
get diagnostics info 31
get dimming 32
get display mode 33
get format 34
get freeze 35
get gamma 36
get general info 37
get geometry adjust info 38
get H start 39
get high altitude 40
get image setting info 41
get input black balance 42
get input selection 43
get input white balance 44
get internal pattern 45
get IP configuration info 46
get lamp max runtime 47
get lamp on 48
get lamp runtime 49
get lamp status 50
get language 51
get main zoom 52
get menu position 53
get no signal color logo 54
get noise reduction 55
get phase 56
get PIP enable 57
get PIP select 59
get PIP size 60
get rear projection mode 61
get resolution 62
get saturation 63
get serial number 64
get sharpness 65
get tint 66
get V start 67
get versions 68
get warp keystone vertical 69
Representation 12
reset settings to factory defaults 71
write 71
RS232 11
RS422 11
S
set aspect ratio file 72
write 72
set auto image adjust 73
write 73
set auto power off 74
write 74
set auto power on 75
write 75
set auto source 76
write 76
set brightness 77
write 77
set ceiling mode 78
write 78
set color temperature 79
write 79
116
set color wheel index 80
write 80
set contrast 81
write 81
set dimming 82
write 82
set display mode 83
write 83
set format 84
write 84
set freeze 85
write 85
set gamma 86
write 86
set H start 87
write 87
set high altitude 88
write 88
set input black balance 89
write 89
set input selection 90
write 90
set input white balance 91
write 91
set internal pattern 92
write 92
set language 93
write 93
set lens center 94
write 94
set lens focus 95
write 95
set lens shift 96
write 96
set lens zoom 97
write 97
set main zoom 98
write 98
set menu position 99
write 99
set no signal color logo 100
write 100
set noise reduction 101
write 101
set phase 102
write 102
set PIP enable 103
write 103
set PIP position 104
write 104
set PIP select 105
write 105
set PIP size 106
write 106
set projector power on/off 107
write 107
set rear projection mode 108
write 108
set saturation 109
write 109
set sharpness 110
write 110
set TCP/IP 111
write 111
set tint 112
write 112
set V start 113
write 113
set warp keystone vertical 114
write 114
U
USB-B
11
R5905745 COMMAND CATALOG 07/05/2015
Index
W
write 16–17, 58, 70–114
AV mute 16
decrement noise reduction 17
get PIP position 58
increment noise reduction 70
reset settings to factory defaults
set aspect ratio file 72
set auto image adjust 73
set auto power off 74
set auto power on 75
set auto source 76
set brightness 77
set ceiling mode 78
set color temperature 79
set color wheel index 80
set contrast 81
set dimming 82
set display mode 83
set format 84
set freeze 85
set gamma 86
set H start 87
set high altitude 88
set input black balance 89
71
R5905745 COMMAND CATALOG 07/05/2015
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
set
input selection 90
input white balance 91
internal pattern 92
language 93
lens center 94
lens focus 95
lens shift 96
lens zoom 97
main zoom 98
menu position 99
no signal color logo 100
noise reduction 101
phase 102
PIP enable 103
PIP position 104
PIP select 105
PIP size 106
projector power on/off 107
rear projection mode 108
saturation 109
sharpness 110
TCP/IP 111
tint 112
V start 113
warp keystone vertical 114
117
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement