Land Pride SF25 Series Operator Manual

Land Pride SF25 Series Operator Manual
Table of Contents
Scarifiers
SF2566 & SF2577
10401
302-188M
Operator’s Manual
!
Read the Operator’s Manual entirely. When you
see this symbol, the subsequent instructions and
warnings are serious - follow without exception.
Your life and the lives of others depend on it!
Cover photo may show optional equipment
not supplied with standard unit.
© Copyright 2014
Printed
11/10/15
Machine Identification
Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new
manual.
If you, or the dealer, have added Options not originally ordered with the machine, or removed Options that were
originally ordered, the weights and measurements are no longer accurate for your machine. Update the record by
adding the machine weight and measurements provided in the Specifications & Capacities Section of this manual with
the Option(s) weight and measurements.
Model Number
Serial Number
Machine Height
Machine Length
Machine Width
Machine Weight
Delivery Date
First Operation
Accessories
Dealer Contact Information
Name:
Street:
City/State:
Telephone:
Email:
!
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
Table of Contents
Table of Contents
Important Safety Information . . . . . . . . . . . 1
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . . 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
Application . . . . . . . . . . . . . . . .
Using This Manual . . . . . . . . . .
Owner Assistance . . . . . . . . . . .
Serial Number . . . . . . . . . . . .
...............4
...............4
...............4
...............4
Section 1: Assembly & Set-Up . . . . . . . . . . 5
SF25 Assembly . . . . . . . . . . . .
Accessory Attachments . . . . . .
Tractor Hook-Up . . . . . . . . . . . .
Unhook Scarifier . . . . . . . . . . . .
...............5
...............5
...............6
...............6
Section 2: Operating . . . . . . . . . . . . . . . . . 7
Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . . 7
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
General Operating Instructions . . . . . . . . . . . . . . . . 7
Scarifier Used Alone . . . . . . . . . . . . . . . . . . . . . . 7
Scarifier Used With a Landscape Rake . . . . . . . . 7
Scarifier Used with a Rear Blade . . . . . . . . . . . . 7
Final Comments . . . . . . . . . . . . . . . . . . . . . . . . . 7
Section 3: Adjustments . . . . . . . . . . . . . . . 8
Shank Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Section 4: Maintenance . . . . . . . . . . . . . . . 9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Shank Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . 9
Section 5: Specifications & Capacities . . 10
Section 6: Features & Benefits . . . . . . . . 11
Section 7: Torque Values Chart . . . . . . . . 12
Section 8: Warranty . . . . . . . . . . . . . . . . . 13
© Copyright 2014 All rights Reserved
Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.
Land Pride is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
SF2566 & SF2577 Scarifiers 302-188M
11/10/15
Table of Contents
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Safety at All Times
Look For The Safety Alert Symbol
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read all
instructions noted on them.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention are
dependent upon the awareness, concern, prudence, and
proper training of personnel involved in the operation,
transport, maintenance, and storage of equipment.
▲ The operator must not use drugs
or alcohol as they can change the
alertness or coordination of that
person while operating equipment.
The operator should, if taking overthe-counter drugs, seek medical
advice on whether he/she can
safely operate the equipment.
▲ Operator should be familiar with all
functions of the unit.
▲ Operate controls from the driver’s
seat only. Never operate controls
from the ground.
▲ Make sure all guards and shields
are in place and secured before
operating implement.
▲ Keep all bystanders away from
equipment and work area.
▲ Do not leave tractor or implement
unattended with engine running.
▲ Dismounting from a moving tractor
can cause serious injury or death.
▲ Do not allow anyone to stand
between tractor and implement
while backing up to implement.
▲ Keep hands, feet, and clothing
away from power-driven parts.
▲ Watch out for fences, trees, rocks,
wires, etc., while operating and
transporting implement.
▲ Turning tractor too tight may cause
hitched machinery to ride up on
wheels. This could result in injury
or equipment damage.
11/10/15
!
Be Aware of
Signal Words
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
! DANGER
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
! WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
! CAUTION
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
For Your Protection
Tractor Shutdown & Storage
▲ Thoroughly read and understand
the “Safety Label” section, read
all instructions noted on them.
▲ If engaged, disengage PTO.
▲ Lower attached implement to
ground, put tractor in park or set
park brake, turn off engine, and
remove switch key to prevent
unauthorized starting.
▲ Wait for all components to come to
a complete stop before leaving the
operator’s seat.
▲ Detach and store implement in an
area where children normally do
not play. Secure implement using
blocks and supports.
OFF
R E MO
VE
Parts Manual QR Locator
Dealer QR Locator
The QR (Quick Reference) code on the
cover and to the left will take you to the
Parts Manual for this equipment.
Download the appropriate App on your
smart phone, open the App, point your
phone on the QR code and take a picture.
The QR code on the left will
link you to available dealers
for Land Pride products.
Refer to Parts Manual QR
Locator on this page for
detailed instructions.
SF2566 & SF2577 Scarifiers 302-188M
1
Table of Contents
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
2
Use Safety
Lights and Devices
Transport
Machinery Safely
▲ Slow moving tractors,
self-propelled equipment, and
towed implements can create a
hazard when driven on public
roads. They are difficult to see,
especially at night.
▲ Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
▲ Comply with state and local laws.
▲ Use towing vehicle and trailer of
adequate size and capacity.
▲ Secure equipment towed on a
trailer with tie downs and chains.
▲ Sudden braking can cause a trailer
to swerve and upset. Reduce
speed if trailer is not equipped with
brakes.
▲ Avoid contact with any over head
utility lines or electrically charged
conductors.
▲ Engage park brake when stopped
on an incline.
Use A Safety Chain
Practice Safe Maintenance
▲ A safety chain will help control
drawn machinery should it
separate from the tractor drawbar.
▲ Use a chain with the strength
rating equal to or greater than the
gross weight of the towed
machinery.
▲ Attach the chain to the tractor
drawbar support or other specified
anchor location. Allow only
enough slack in the chain to
permit turning.
▲ Do not use safety chain for towing.
▲ Understand procedure before doing
work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
▲ Work in a clean dry area.
▲ Lower attached implement to the
ground, put tractor in park, turn off
engine, and remove key before
performing maintenance.
▲ Allow implement to cool before
working on it.
▲ Disconnect battery ground cable (-)
before servicing or adjusting
electrical systems or before welding
on implement.
SF2566 & SF2577 Scarifiers 302-188M
▲ Maximum transport speed for an
attached implement is 20 mph. DO
NOT EXCEED. Never travel at a
speed which does not allow
adequate control of steering and
stopping. Some rough terrains
require a slower speed.
▲ As a guideline, use the following
maximum speed weight ratios for
an attached implement:
20 mph when weight of attached
implement is less than or equal to
the weight of machine towing the
implement.
10 mph when weight of attached
implement exceeds weight of
machine towing implement but
not more than double the weight.
▲ IMPORTANT: Do not tow a load
that is more than double the weight
of the machine towing the load.
▲ Do not grease or oil implement
while it is in operation.
▲ Inspect all parts. Make certain
parts are in good condition &
installed properly.
▲ Replace parts on this machine with
genuine Land Pride parts only. Do
not alter this machine in a way
which will adversely affect its
performance.
▲ Remove buildup of grease, oil, or
debris.
▲ Remove all tools and unused parts
from implement before operation.
11/10/15
Table of Contents
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Prepare for Emergencies
▲ Be prepared if a fire starts.
▲ Keep a first aid kit and fire
extinguisher handy.
▲ Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
Wear
Protective Equipment
Avoid High
Pressure Fluids Hazard
▲ Wear protective clothing and
equipment appropriate for the job
such as safety shoes, safety
glasses, hard hat, and ear plugs.
▲ Clothing should fit snug without
fringes and pull strings to avoid
entanglement with moving parts.
▲ Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
▲ Operating equipment safely
requires the operator’s full
attention. Avoid wearing radio
headphones while operating
machinery.
▲ Escaping fluid under pressure can
penetrate the skin causing serious
injury.
▲ Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
▲ Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
▲ Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
▲ Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
▲ DO NOT DELAY. If an accident
occurs, see a doctor familiar with
this type of injury immediately. Any
fluid injected into the skin or eyes
must be treated within
a few hours or
gangrene may
result.
Use Seat Belt and ROPS
Keep Riders Off
Machinery
911
Avoid Underground
Utilities
▲ Dig Safe, Call 811.
Always contact your local utility
companies (electrical, telephone,
gas, water, sewer, and others)
before digging so that they may
mark the location of any
underground services in the area.
▲ Be sure to ask how close you can
work to the marks they positioned.
11/10/15
▲ Operate only tractors equipped
with a Roll-Over Protective
Structure (ROPS) and seat belt.
▲ Fasten seat belt snugly and
securely to help protect against
serious injury or death from falling
and tractor overturn.
▲ Wear protective equipment such
as a hard hat, safety shoes, safety
glasses, and ear plugs.
▲ Never carry riders or use
machinery as a person lift.
▲ Riders obstruct operator’s view.
▲ Riders could be struck by foreign
objects or thrown from the
machine.
▲ Never allow children to operate
equipment.
SF2566 & SF2577 Scarifiers 302-188M
3
Table of Contents
Introduction
Introduction
Land Pride welcomes you to the growing family of new
product owners.
This Scarifier has been designed with care and built by
skilled workers using quality materials. Proper assembly,
maintenance, and safe operating practices will help you
get years of satisfactory use from this machine.
Application
The SF2566 and SF2577 Scarifiers are designed and
built by Land Pride to perform ripping, loosening, and
renovation or reshaping of the soil profile. These
Scarifiers offer 60" and 72" working widths and are
adapted for Category 1 3-Point hitch mounting to tractors
with 25 to 50 horsepower capabilities. Both models are
designed for tandem attachment and will work in unison
with Land Pride 15 and 25 Series Landscape Rakes or
Land Pride Rear Blades.
The versatile action of a Scarifier that can be used
simultaneously with a landscape rake or rear blade
makes the Land Pride Scarifiers perfectly suited for use
by landscapers, contractors, and rental yards. These
units have applications at housing and road construction
projects, golf courses, terracing sites, run-off control
projects, and reforestation sites.
Owner Assistance
The Online Warranty Registration or Warranty
Registration card should be completed by the dealer at
the time of purchase. This information is necessary to
provide you with quality customer service.
The parts on your Scarifier have been specially designed
by Land Pride and should only be replaced with genuine
Land Pride parts. Contact a Land Pride dealer if customer
service or repair parts are required. Your Land Pride
dealer has trained personnel, repair parts, and
equipment needed to service the implement.
Serial Number
Model No. _____________Serial No. ______________
For quick reference and prompt service, record model
number and serial number in the spaces provided above
and again on warranty page 13. Always provide model
and serial number when ordering parts and in all
correspondences with your Land Pride dealer. Refer to
Figure 1 for location of your serial number plate.
See “Specifications & Capacities” on page 10 and
“Features & Benefits” on page 11 for additional
information and performance enhancing options.
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
10401
Serial Number Plate Location
Figure 1
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge from our website at
www.landpride.com.
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
IMPORTANT: A special point of information related
to the following topic. Land Pride’s intention is this
information must be read & noted before continuing.
NOTE: A special point of information that the
operator should be aware of before continuing.
Further Assistance
Your dealer wants you to be satisfied with your new
Scarifier. If for any reason you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:
1.
Discuss the matter with your dealership service
manager making sure that person is aware of any
problems you may have and has had the opportunity
to assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem, and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpservicedept@landpride.com
4
SF2566 & SF2577 Scarifiers 302-188M
11/10/15
Table of Contents
Section 1: Assembly & Set-Up
Section 1: Assembly & Set-Up
SF25 Assembly
Accessory Attachments
Refer to Refer to Figure 1-1:
1. Attach 3-Point upper link (#10) to Scarifier frame with
hardware as indicated, making certain upper link is
free to pivot.
The Scarifier is designed and built by Land Pride for
piggyback attachment and simultaneous use of Land
Pride 15 and 25 Series Landscape Rakes or 15 and 25
Series Rear Blades. Attach Landscape Rake or Rear
Blade to Scarifier as follows:
2. Position Scarifier frame in an upright, stable position
on suitable supports or attach to tractor 3-Point hitch.
3. Insert shanks (#3) into shank tube from bottom side
with tips pointing towards tractor. Position shank to
desired depth and secure with shank lock pin (#5)
and clip (#6).
1.
Swing lock handle (#7) up and out of the way.
2. Lower frame hitch pins of rear blade or landscape
rake into slot and swing lock handle back to lock hitch
pins in place.
3. Attach upper link (#10) to upper hitch of rear blade or
landscape rake frame. Top hitch pin and linch pins
are to be furnished by customer.
SF25 Dealer Assembly
Figure 1-1
11/10/15
14626
SF2566 & SF2577 Scarifiers 302-188M
5
Table of Contents
Section 1: Assembly & Set-Up
Tractor Hook-Up
7.
Return to the tractor and slowly operate the controls
up and down to check for clearance between
Scarifier and tractor tires, frame and drawbar. Move
or remove the drawbar if it interferes with the
Scarifier.
Refer to Figure 1-2:
!
DANGER!
Tractor hook-up to equipment is dangerous and can result in
serious injury or death. Do not allow anyone to stand between
the Scarifier and tractor during hook-up operations. Do not
operate the hydraulic 3-Point lift controls while someone is
directly behind the tractor or near the Scarifier.
8. Manually adjust one of the two Lower lift arms up or
down to level the Scarifier from left to right.
A 3-Point Category I is required. The lower 3-Point arms
of the 3-Point hitch must be stabilized to prevent side-toside movement. Most tractors have sway blocks or
adjustable chains for this purpose.
Unhook Scarifier
1.
Locate on a flat and level concrete surface.
2. Slowly back tractor up to the Scarifier while using the
tractor’s 3-Point hydraulic control to align the lower
hitch arms ball swivels with the hitch lugs on the
Scarifier.
3. Engage tractor park brake, shut tractor engine off
and remove key before dismounting from tractor.
4. Attach lower arms to the hitch pins and secure with
linch pins. (Linch pins supplied by customer)
5. Connect top center link to the upper hitch using
customer supplied clevis pin and linch pin. If
required, start tractor and slowly raise 3-Point hitch
about 1 - 2" to align center link with Scarifier center
hitch pin hole.
6. Ensure that lower hitch arms are blocked to prevent
excessive side movement.
9. Manually adjust the length of the top center link to
level the Scarifier from front to rear.
!
WARNING!
Scarifiers, without a rake or rear blade attached, can tip over
while unhooking from a tractor. Secure Scarifier with bracing
before unhooking from the unit.
1.
Park on a level solid surface.
2. Lower Scarifier until teeth are resting on level ground
or until its main beam is resting on solid supports.
3. Engage tractor park brake, shut tractor engine off
and remove key before dismounting from tractor.
4. Stabilize Scarifier with bracing before unhooking
tractor’s 3-Point arms. Make sure bracing is secure
and will not slip while unhooking.
5. Unhook 3-Point hitch from tractor. Reinstall hitch
pins, linchpins, and hair pin cotters in Scarifier hitch
for safe keeping.
6. Remove bracing and rotate Scarifier down so that it is
laying on the ground or use auxiliary supports such
as post planted in the ground to prevent the
possibility of the unit tipping over.
24711
Tractor Hook-Up
Figure 1-2
6
SF2566 & SF2577 Scarifiers 302-188M
11/10/15
Table of Contents
Section 2: Operating
Section 2: Operating
Operating Checklist
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the Scarifier. Therefore, it is absolutely
essential that no one operates the Scarifier without first
having read, fully understood, and become totally familiar
with the Operator’s Manual. Make sure the operator has
paid particular attention to:
• Important Safety Information, pages 1 to 3
• Section 1: Assembly & Set-Up, page 5
• Section 2: Operating, page 7
• Section 3: Adjustments, page 8
Make the following inspections after attaching Scarifier to
tractor. See “Tractor Hook-Up” on page 6.
1.
Inspect tractor safety equipment to make sure it is in
good working condition.
2. Carefully raise and lower the implement to ensure
that the drawbar, tires, and other equipment on the
tractor do not contact the frame.
3. Check initially and periodically for loose bolts and
pins. See “Torque Values Chart for Common Bolt
Sizes” on page 12.
Transporting
! CAUTION!
When traveling on public roads whether at night or during the
day, use accessory light and devices for adequate warning to
operators of other vehicles. Comply with all federal, state, and
local laws.
1.
When raising the Scarifier to transport position, be
sure that the equipment does not make contact with
the tractor and tractor drawbar. Move or remove
drawbar if it interferes with the Scarifier.
2. Be sure to reduce tractor ground speed when
turning; and, leave enough clearance so that the
Scarifier does not contact obstacles such as
buildings, trees, or fences.
3. Select a safe ground travel speed when transporting
from one area to another. When traveling on
roadways, transport in such a way that faster moving
vehicles may pass you safely.
4. When traveling over rough or hilly terrain, shift tractor
to a lower gear.
General Operating Instructions
Before using your Land Pride Scarifier, it is very
important that you read the Operator’s Manual. The
SF2566 and SF2577 Scarifiers are designed and built by
Land Pride for piggyback attachment and simultaneous
use of the Land Pride 15 and 25 Series Landscape Rakes
or 15 and 25 Series Rear Blades. This dual capability
makes it very important that you understand how to
11/10/15
properly adjust your Scarifier shanks for proper
simultaneous use with either a rake or a blade. This
information is found in your Operator’s Manual under
“Shank Settings” on page 8.
Scarifier Used Alone
It is not absolutely necessary that another attachment be
used in unison with the Land Pride Scarifier. Scarifying
alone is usually done to loosen the soil profile for planting
of trees or to increase soil percolation in order to
eliminate standing water problems.
When using the Scarifier alone, you should be able to rip
and loosen soil to the depth you can sink the shank tips
and still maintain forward pulling momentum. The more
compacted the soil, the more horsepower it will take to
get the job done. In any case, you will want to use a lower
gear selection and you may need to make more than one
pass. Progressive lengthening of the shanks and multiple
passes may be required to achieve the maximum depth.
Scarifier Used With a Landscape Rake
Using your Scarifier in tandem with a landscape rake is a
good combination for removing 1" to 4" size rocks that
have become imbedded in the topsoil.
Set the rake angle to move the loosened rocks to the
desired side. Set the Scarifier shank tips to an
appropriate depth below the bottom of the rake teeth. See
“Shank Settings” on page 8.
As you travel forward loosening the ground, the rake
should separate the rocks and roll them off to the side. If
the soil is breaking into clumps that are too large, raise
the Scarifier shanks and continue.
Scarifier Used with a Rear Blade
Using a rear blade in tandem with a Scarifier is a
combination tool for totally renovating or modifying the
soil profile.
When you want to change the grade of a certain area, set
the rear blade at the appropriate angle and set the shank
tips to your choice of working depth below the blade. See
“Shank Settings” on page 8.
As you travel forward loosening the soil, the rear blade
will redistribute the dirt to the side you have chosen with
your blade angle setting. If the soil is breaking into
clumps larger than you want, raise the shank tips until
you achieve the desired working consistency.
Final Comments
A little practice and experience working with the different
attachment combinations and adjustments that are
possible with your Land Pride Scarifier should make you
highly effective in a very short amount of time.
See Section 5: Specifications & Capacities on page 10
and “Section 6: Features & Benefits” on page 11 for
additional information and performance enhancing
options.
SF2566 & SF2577 Scarifiers 302-188M
7
Table of Contents
Section 3: Adjustments
Section 3: Adjustments
Shank Settings
It is very important to understand how to properly adjust
the Scarifier shanks when working this unit simultaneous
with either the LR15 and LR25 Series Landscape Rake
or RB15 and RB25 Series Rear Blade.
!
DANGER!
!
CAUTION!
Refer to Figure 1-1 on page 5:
1. Remove hairpin (#6) and shank lock pin (#5).
2. Adjust each shank up or down to the desired hole
location. See Shank Settings Table below for
distances above and below auxiliary equipment.
3. Reinsert shank lock pin (#5) and secure in place with
hair pin (#6).
Make adjustments to the Scarifier after it has been properly
attached to a tractor and secured with solid supports. Never
work around equipment supported by hydraulics. Hydraulics
can drop equipment instantly if controls are actuated or if
hydraulic lines burst even when power to hydraulics is shut
off.
Always keep your feet and legs out from under the shanks
while adjusting them. It is possible for the shanks to fall
causing injury to your feet and/or legs.
Shank Settings
LR15 & LR25 Series Landscape Rakes
Shank Hole Position
8
Distance From
Tip of Rake Teeth
LR15 & LR25 Series Rear Blade
Shank Hole Position
Distance From
Blade Cutting Edge
Top Hole
4 1/2" Below
Top Hole
4" Below
2nd Hole
2 1/2" Below
2nd Hole
2" Below
3rd Hole
1/2" Below
3rd Hole
Even with cutting edge
Bottom Hole
1 1/2" Above
Bottom Hole
2" Above
SF2566 & SF2577 Scarifiers 302-188M
11/10/15
Table of Contents
Section 4: Maintenance
Section 4: Maintenance
Maintenance
Long Term Storage
Proper servicing and adjustments are key to the long life
of any implement. With careful inspection and routine
maintenance, you can avoid costly downtime and repair.
Clean, inspect, service, and make necessary repairs to
the Scarifier when parking it for long periods and when
parking it at the end of a working season. This will help
ensure that the Scarifier is ready for field use the next
time you hook-up to it.
The parts on your Scarifier have been specially designed
and should only be replaced with genuine Land Pride
parts.
1.
After several hours of use and on a regular basis
thereafter check all bolts and pins to be sure they are
tight. Replace worn, damaged, or missing parts.
Replace any worn, damaged, or illegible safety alert
labels by obtaining new labels from your Land Pride
dealer.
Do not alter the Scarifier in a way which will adversely
affect its performance.
!
WARNING!
Never work under the Scarifier without blocking it up properly
first. The Scarifier can fall causing bodily injury or death.
Equipment supported by hydraulics can drop instantly if
controls are actuated or if hydraulic lines burst even when
power to hydraulics is shut off.
! DANGER!
Always support underside of Scarifier with solid supports
before working beneath unit. Never work under equipment
supported by hydraulics. Hydraulics can drop equipment
instantly if controls are actuated even when power to
hydraulics is shut off.
!
2. Check teeth for wear and replace if necessary.
3. Inspect Scarifier for loose, damaged, or worn parts.
Adjust and tighten loose parts or replace if needed.
4. Clean dirt, oil, and grease from areas where paint
has been worn, chipped, or scratched. Prime bare
metal surfaces after cleaning and repaint to prevent
rust. Ask your dealer for Land Pride aerosol touch-up
paint. They are also available in touch-up bottles with
brush, quarts, and gallon sizes by adding TU, QT, or
GL to the end of the aerosol part number.
Land Pride Aerosol Touch-up Paint
Part No.
Part Description
821-011C
821-002C
821-066C
PAINT LP BEIGE AEROSOL SPRAY CAN
PAINT LP BLACK AEROSOL SPRAY CAN
PAINT ORANGE AEROSOL SPRAY CAN
5. Replace all damaged or missing decals.
6. Apply a light coat of oil or grease may be applied to
the teeth to minimize oxidation.
7.
CAUTION!
Do not alter Land Pride equipment or replace parts with other
brands. Doing so can cause equipment to perform improperly
and may lead to breakage that can cause bodily injury.
Replace parts only with genuine Land Pride parts.
Clean off any dirt or grease that may have
accumulated on the Scarifier. Scrape off compacted
dirt and then wash the surface thoroughly with a
garden hose.
Follow unhooking instructions when disconnecting
Scarifier from tractor. Refer to “Unhook Scarifier” on
the left-hand side of this page.
• Store Scarifier in a clean, dry place. Inside storage
•
Shank Tips
Refer to Figure 4-1:
Shank tips are removable by heating them in the dimpled
area on both sides and knocking them off with a blunt
punch. New shank tips need to be dimpled with a punch
after they are installed. Use Land Pride shank tips only.
will reduce maintenance and make for a longer
Scarifier life.
Lay unit down on the ground or ensure that the
main frame is stable by using auxiliary supports
such as posts planted in the ground to prevent the
possibility of the unit tipping over.
39257
Shank Tip Removal
Figure 4-1
11/10/15
SF2566 & SF2577 Scarifiers 302-188M
9
Table of Contents
Section 5: Specifications & Capacities
Section 5: Specifications & Capacities
SF25 Series
SF2566
SF2577
Scarifier Width
66”
77”
Working Width
60”
72”
Approximate Weight/LBS.
208
235
6
7
Number of Shanks
Number of Adjustments
Horsepower Rating/Engine
4 adjustments in 2” increments
25 to 50 HP
Hitch Type
Limited Cat.1 with Floating Top Link for Second Implement
Shank Type
3/4” x 2 1/2” Heat Treated Spring Steel Shanks
with Dimpled-On Tips
27517
10
SF2566 & SF2577 Scarifiers 302-188M
11/10/15
Table of Contents
Section 6: Features & Benefits
Section 6: Features & Benefits
SF25 Series
Features
Benefits
Working widths
60” & 72”
Tractor HP range
25-50 HP
Cat 1 3-Point hitch
For easy attachment to a wide range of tractors
Four ripping depths
Good variation in ripping depth.
Heat treated steel shanks
Won’t bend or break.
Replaceable shank tips
Can be easily replaced when damaged or worn without having to replace entire shank.
Rear hitch with
floating top link
Allows for second implement to work in conjunction with the Scarifier such as a Landscape
Rake. Compatible with Land Pride 15 & 25 Series Rakes and Blades.
5/16” Wall thickness
on the shank tube
High tensile strength to take the pressure from the shanks.
5/16” x 1” Full length
reinforcement bar
Adds additional strength to shank tube right behind shank where pressure is applied while
dragging through the ground.
Warranty
One year parts and labor.
11/10/15
SF2566 & SF2577 Scarifiers 302-188M
11
Table of Contents
Section 7: Torque Values Chart
Section 7: Torque Values Chart
Torque Values Chart for Common Bolt Sizes
Bolt Head Identification
Bolt Size
(inches)
1
Grade 2
2
Grade 5
3
Bolt Head Identification
Grade 8
in-tpi
1/4" - 20
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
N·m
7.4
8.5
15
17
27
31
43
ft-lb
5.6
6
11
13
20
22
32
N·m
11
13
24
26
42
47
67
ft-lb
8
10
17
19
31
35
49
N·m
16
18
33
37
59
67
95
ft-lb
12
14
25
27
44
49
70
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
49
66
75
95
105
36
49
55
70
79
75
105
115
150
165
55
76
85
110
120
105
145
165
210
235
78
105
120
155
170
5/8" - 11
130
97
205
150
285
5/8" - 18
150
110
230
170
325
3/4" - 10
235
170
360
265
510
3/4" - 16
260
190
405
295
570
7/8" - 9
225
165
585
430
820
7/8" - 14
250
185
640
475
905
1" - 8
340
250
875
645 1230
1" - 12
370
275
955
705 1350
1-1/8" - 7
480
355 1080
795 1750
1-1/8" - 12
540
395 1210
890 1960
1-1/4" - 7
680
500 1520
1120 2460
1-1/4" - 12
750
555 1680 1240 2730
1-3/8" - 6
890
655 1990 1470 3230
1-3/8" - 12
1010
745 2270 1670 3680
1-1/2" - 6
1180
870 2640 1950 4290
1-1/2" - 12
1330
980 2970 2190 4820
Torque tolerance + 0%, -15% of torquing values. Unless
12
SF2566 & SF2577 Scarifiers 302-188M
Bolt Size
(Metric)
mm x pitch
M 5 X 0.8
M6X1
M 8 X 1.25
M8X1
M10 X 1.5
M10 X 0.75
M12 X 1.75
M12 X 1.5
M12 X 1
M14 X 2
M14 X 1.5
M16 X 2
4
5.8
8.8
10.9
Class 5.8
Class 8.8
Class 10.9
N·m
4
7
17
18
33
39
58
ft-lb
3
5
12
13
24
29
42
N·m
6
11
26
28
52
61
91
ft-lb
5
8
19
21
39
45
67
N·m
9
15
36
39
72
85
125
ft-lb
7
11
27
29
53
62
93
60
90
92
99
145
44
66
68
73
105
95
105
145
155
225
70
77
105
115
165
130
145
200
l215
315
97
105
150
160
230
210 M16 X 1.5
155
115
240
180
335
245
240 M18 X 2.5
195
145
310
230
405
300
375 M18 X 1.5
220
165
350
260
485
355
420 M20 X 2.5
280
205
440
325
610
450
605 M20 X 1.5
310
230
650
480
900
665
670 M24 X 3
480
355
760
560 1050
780
910 M24 X 2
525
390
830
610
1150
845
995 M30 X 3.5
960
705 1510
1120 2100 1550
1290 M30 X 2
1060
785 1680 1240 2320 1710
1440 M36 X 3.5
1730 1270 2650 1950 3660 2700
1820 M36 X 2
1880 1380 2960 2190 4100 3220
2010 1 in-tpi = nominal thread diameter in inches-threads per inch
2380 2 N· m = newton-meters
2710 3 ft-lb= foot pounds
3160 4 mm x pitch = nominal thread diameter in millimeters x thread
3560 pitch
otherwise specified use torque values listed above.
11/10/15
Table of Contents
Section 8: Warranty
Section 8: Warranty
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit: One year Parts and Labor
Shanks: Considered wear items
This Warranty is limited to the repair or replacement of any defective part by
Land Pride and the installation by the dealer of any such replacement part, and
does not cover common wear items. Land Pride reserves the right to inspect any
equipment or parts which are claimed to have been defective in material or
workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.
Claims under this Warranty should be made to the dealer which originally sold
the product and all warranty adjustments must be made through an authorized
Land Pride dealer. Land Pride reserves the right to make changes in materials or
design of the product at any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in this
written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days from
the date of purchase by the end user.
IMPORTANT: The Online Warranty Registration should be completed by the dealer at the time of
purchase. This information is necessary to provide you with quality customer service.
Model Number ____________________
11/10/15
Serial Number ____________________
SF2566 & SF2577 Scarifiers 302-188M
13
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement