Land Pride CP30 Series Operator Manual

Land Pride CP30 Series Operator Manual
Table of Contents
Cold Planer
AP-CP30 Series
Low Flow Models: CP3012LF and CP3016LF,
High Flow Models: CP3018, CP3024, CP3030, CP3040, and CP3048
72082
72083
CP30 Series of Low-Flow Cold Planers
CP30 Series of High-Flow Cold Planers
350-376MK
Operator’s Manual
!
Read the Operator’s Manual entirely. When you see this symbol,
the subsequent instructions and warnings are serious - follow
without exception. Your life and the lives of others depend on it!
Cover photo may show optional equipment not supplied
with standard unit.
For an Operator’s Manual and Decal Kit in French
Language, please see your Kubota dealer.
Printed 6/13/19
Machine Identification
Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new
manual.
If you, or the dealer, have added Options not originally ordered with the machine, or removed Options that were
originally ordered, the weights and measurements are no longer accurate for your machine. Update the record by
adding the machine weight and measurements provided in the Specifications & Capacities Section of this manual with
the Option(s) weight and measurements.
Model Number
Serial Number
Machine Height
Machine Length
Machine Width
Machine Weight
Delivery Date
First Operation
Accessories
Dealer Contact Information
Name:
Street:
City/State:
Telephone:
Email:
!
California Proposition 65
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Table of Contents
Important Safety Information . . . . . . . . . . . . . 1
Section 4: Maintenance & Lubrication . . . . . 27
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol . . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Servicing Drivetrain Components . . . . . . . . . . . . . 27
Cutting Drum Maintenance . . . . . . . . . . . . . . . . . . 27
Remove & Install Picks . . . . . . . . . . . . . . . . . . . . . 28
Pick Holder Repair . . . . . . . . . . . . . . . . . . . . . . . . 28
Planetary Gearbox Oil Change . . . . . . . . . . . . . . . 29
Long-Term Storage . . . . . . . . . . . . . . . . . . . . . . . . 29
Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . . 30
Low-Flow Cold Planers . . . . . . . . . . . . . . . . . . . 30
Sideshift Bars . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Dead Shaft Bearing . . . . . . . . . . . . . . . . . . . . . .30
Depth Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Tilt Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
High-Flow Cold Planers . . . . . . . . . . . . . . . . . . . 32
Sideshift Bars . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Left and Right Depth Skids . . . . . . . . . . . . . . . .32
Dead Shaft Bearing . . . . . . . . . . . . . . . . . . . . . .33
Depth Cylinder Pivot Pins . . . . . . . . . . . . . . . . .33
Planetary Gearbox . . . . . . . . . . . . . . . . . . . . . . .33
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . 12
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 12
Section 1: Assembly & Set-up . . . . . . . . . . . 13
Skid Steer Requirements . . . . . . . . . . . . . . . . . . .
Torque Requirements . . . . . . . . . . . . . . . . . . . . . .
Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . .
Skid Steer Shutdown Procedure . . . . . . . . . . . . . .
Dealer Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low-Flow Cold Planer Set-up . . . . . . . . . . . . . . . .
Hydraulic Couplers . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Hoses and Fittings . . . . . . . . . . . . . . .
Drum Assembly . . . . . . . . . . . . . . . . . . . . . . . . .
High-Flow Cold Planer Set-up . . . . . . . . . . . . . . . .
Hydraulic Couplers . . . . . . . . . . . . . . . . . . . . . . .
Hoses and Fittings . . . . . . . . . . . . . . . . . . . . . . .
Wire Harness . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drum Assembly . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Case Drain . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
13
14
14
14
14
14
14
15
15
15
15
15
15
Section 2: Operating Procedures . . . . . . . . . 16
General Safety Information . . . . . . . . . . . . . . . . . .
Hook-up Cold Planer . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Hose Hook-up . . . . . . . . . . . . . . . . . . . .
Electrical Hook-up . . . . . . . . . . . . . . . . . . . . . . . . .
Pre-Operation Inspection . . . . . . . . . . . . . . . . . . .
Check Equipment Clearances . . . . . . . . . . . . . . . .
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating the Low-Flow Cold Planer . . . . . . . . .
Operating the High-Flow Cold Planer . . . . . . . . .
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unhook Cold Planer . . . . . . . . . . . . . . . . . . . . . . .
Section 5: Specifications & Capacities . . . . . 34
Section 6: Features & Benefits . . . . . . . . . . . 35
Section 7: Troubleshooting . . . . . . . . . . . . . . 36
Section 8: Torque Values Chart . . . . . . . . . . . 37
Section 9: Warranty & Legal Disclaimer . . . . 38
16
17
18
20
22
22
23
23
24
25
25
Section 3: Options & Accessories . . . . . . . . 26
Picks (Accessory) . . . . . . . . . . . . . . . . . . . . . . . . . 26
Water Spray Kit (Accessory) . . . . . . . . . . . . . . . . . 26
© Copyright 2019 All rights Reserved
Kubota provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Kubota
assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Kubota reserves the right
to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
Kubota is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
6/13/19
AP-CP30 Series Cold Planer 350-376MK
Table of Contents
Table of Contents Continued
See previous page for Table of Contents.
Parts Manual QR Locator
Dealer QR Locator
The QR (Quick Reference) code on the
cover and to the left will take you to the
Parts Manual for this equipment.
Download the appropriate App on your
smart phone, open the App, point your
phone on the QR code and take a picture.
The QR code on the left will
link you to available dealers
for Kubota products. Refer to
Parts Manual QR Locator on
this page for detailed
instructions.
AP-CP30 Series Cold Planer 350-376MK
6/13/19

Important Safety Information
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Safety at All Times
Careful operation is your best
assurance against an accident.
All operators, no matter how much
experience they may have, should
carefully read this manual and
other related manuals, or have the
manuals read to them, before
operating the power machine and
this attachment.
 Thoroughly read and understand
the “Safety Label” section. Read
all instructions noted on them.
 Do not operate the equipment
while under the influence of drugs
or alcohol as they impair the ability
to safely and properly operate the
equipment.
 Operator should be familiar with all
functions of the skid steer and
attachment and be able to handle
emergencies quickly.
 Make sure all guards and shields
appropriate for the operation are in
place and secured before
operating the attachment.
 Keep all bystanders away from
equipment and work area.
 Start skid steer from the driver’s
seat with steering levers and
hydraulic controls in neutral.
 Operate skid steer and controls
from the driver’s seat only.
 Never dismount from a moving
skid steer or leave skid steer
unattended with engine running.
 Do not allow anyone to stand
between attachment and skid
steer while hooking-up.
 Keep hands, feet, and clothing
away from power-driven parts.
 While transporting and operating
equipment, watch out for objects
overhead and along side such as
fences, trees, buildings, wires, etc.
 Store attachment in an area where
children normally do not play.
When needed, secure attachment
against falling with support blocks.
6/13/19
!
Look for the Safety Alert Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention are
dependent upon the awareness, concern, prudence, and
proper training of personnel involved in the operation,
transport, maintenance, and storage of equipment.
Be Aware of
Signal Words
A signal word designates a degree or
level of hazard seriousness. The
signal words are:
! DANGER
Indicates a hazardous situation that, if
not avoided, will result in death or
serious injury.
! WARNING
Indicates a hazardous situation that, if
not avoided, could result in death or
serious injury.
! CAUTION
Indicates a hazardous situation that, if
not avoided, may result in minor or
moderate injury.
Safety Precautions for
Children
Skid Steer Shutdown
And Storage
Tragedy can occur if the operator
is not alert to the presence of
children. Children generally are
attracted to attachments and their
work.
 Never assume children will remain
where you last saw them.
 Keep children out of the work area
and under the watchful eye of a
responsible adult.
 Be alert and shut the attachment
and skid steer/track loader down if
children enter the work area.
 Never carry children on the power
machine or attachment. There is
not a safe place for them to ride.
They may fall off and be run over
or interfere with the control of the
power machine.
 Never allow children to operate the
power machine, even under adult
supervision.
 Never allow children to play on the
power machine or attachment.
 Use extra caution when backing
up. Before the power machine
starts to move, look down and
behind to make sure the area is
clear.
 Reduce engine speed and shut-off
all power to the attachment.
 Park on solid, level ground and
lower attachment until it is flat on
the ground or support blocks.
 Turn off engine, and remove
switch key to prevent unauthorized
starting.
 Relieve all hydraulic pressures.
 If included, raise seat bar and
move controls until both lock.
 Wait for all components to stop
before leaving operator’s seat.
 Use steps, grab-handles and
anti-slip surfaces when stepping
on and off the skid steer.
 Detach and store attachment in an
area where children normally do
not play. Secure attachment by
using blocks and supports.
OFF
RE M O
VE
1
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Dig Safe - Avoid
Underground Utilities
 USA: Call 811
CAN: digsafecanada.ca
Always contact your local utility
companies (electrical, telephone,
gas, water, sewer, and others)
before digging so that they may
mark the location of any
underground services in the
area.
 Be sure to ask how close you can
work to the marks they
positioned.
2
Transport Safely
 Comply with federal, state, and local
laws.
 Use towing vehicle and trailer of
adequate size and capacity. Secure
equipment towed on a trailer with
chocks, tie downs, and chains.
 Sudden braking can cause a towed
trailer to swerve and upset. Reduce
speed if towed trailer is not equipped
with brakes.
 Avoid contact with any overhead
utility lines or electrically charged
conductors.
 Always drive with load on end of
loader arms low to the ground.
 Always drive straight up and down
steep inclines with heavy end of skid
steer on the “uphill” side.
Tire Safety
Practice Safe Maintenance
 Tire changing can be dangerous
and must be performed by
trained personnel using the
correct tools and equipment.
 Always maintain correct tire
pressure. Do not inflate tires
above recommended pressures
shown in the Operator’s Manual.
 When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
 Securely support the attachment
when changing a wheel.
 When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
 Make sure wheel bolts have been
tightened to the specified torque.
 Understand procedure before doing
work. Refer to the Operator’s Manual
for additional information.
 Work on a level surface in a clean
dry area that is well-lit.
 Lower attachment to the ground and
follow all shutdown procedures
before leaving the operator’s seat to
perform maintenance.
 Do not work under any hydraulic
supported equipment. It can settle,
suddenly leak down, or be lowered
accidentally. If it is necessary to work
under the equipment, securely
support it with stands or suitable
blocking beforehand.
 Use properly grounded electrical
outlets and tools.
 Use correct tools and equipment for
the job that are in good condition.
 Allow equipment to cool before
working on it.
 Engage park brake when stopped on
an incline.
 Maximum transport speed for an
attached equipment is 20 mph. DO
NOT EXCEED. Never travel at a
speed which does not allow
adequate control of steering and
stopping. Some rough terrains
require a slower speed.
 As a guideline, use the following
maximum speed weight ratios for
attached equipment:
20 mph when weight of attached
equipment is less than or equal to
the weight of machine towing the
equipment.
10 mph when weight of attached
equipment exceeds weight of
machine towing equipment but not
more than double the weight.
 IMPORTANT: Do not tow a load that
is more than double the weight of the
vehicle towing the load.
 Disconnect battery ground cable (-)
before servicing or adjusting
electrical systems or before welding
on equipment.
 Inspect all parts. Make certain parts
are in good condition & installed
properly.
 Replace parts on this attachment
with genuine Kubota parts only. Do
not alter this attachment in a way
which will adversely affect its
performance.
 Do not grease or oil attachment
while it is in operation.
 Remove buildup of grease, oil, or
debris.
 Always make sure any material and
waste products from the repair and
maintenance of the attachment are
properly collected and disposed.
 Remove all tools and unused parts
from the equipment before
operation.
6/13/19
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Prepare for Emergencies
 Be prepared if a fire starts.
 Keep a first aid kit and fire
extinguisher handy.
 Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
Wear Personal Protective
Equipment (PPE)
Avoid High
Pressure Fluids Hazard
 Wear protective clothing and
equipment appropriate for the job
such as safety shoes, safety
glasses, hard hat, and ear plugs.
 Clothing should fit snug without
fringes and pull strings to avoid
entanglement with moving parts.
 Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
 Operating equipment safely
requires the operator’s full
attention. Avoid wearing
headphones while operating
equipment.
 Escaping fluid under pressure
can penetrate the skin causing
serious injury.
 Relieve all residual pressure
before disconnecting hydraulic
lines or performing work on the
hydraulic system.
 Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
 Use a piece of paper or
cardboard, NOT BODY PARTS,
to check for suspected leaks.
 Wear protective gloves and
safety glasses or goggles when
working with hydraulic systems.
 DO NOT DELAY. If an accident
occurs, see a doctor familiar with
this type of injury immediately.
Any fluid injected into the skin or
eyes must be treated
within a few hours or
gangrene may
result.
Use Seat Belt and ROPS
Keep Riders Off
Machinery
911
Use Safety
Lights and Devices
 Slow moving tractors, skid steers,
and self-propelled machines can
create a hazard when driven on
public roads. They are difficult to
see, especially at night. Use the
Slow Moving Vehicle (SMV) sign
when on public roads.
 Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
6/13/19
 Kubota recommends the use of a
CAB or roll-over-protectivestructures (ROPS) and seat belt
in almost all power machines.
Combination of a CAB or ROPS
and seat belt will reduce the risk
of serious injury or death if the
power machine should be upset.
 If ROPS is in the locked-up
position, fasten seat belt snugly
and securely to help protect
against serious injury or death
from falling and machine
overturn.
 Never carry riders on skid steer
or attachment.
 Riders obstruct operator’s view
and interfere with the control of
the power machine.
 Riders can be struck by objects
or thrown from the equipment.
 Never use skid steer or
attachment to lift or transport
riders.
3
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Avoid crystalline Silica
(quartz) Dust
Because crystalline silica is a basic
component of sand and granite,
many activities at construction sites
produce dust containing crystalline
silica. Trenching, sawing, and boring
of material containing crystalline
silica can produce dust containing
crystalline silica particles. This dust
can cause serious injury to the
lungs (silicosis).
There are guidelines which should
be followed if crystalline silica
(quartz) is present in the dust.
 Be aware of and follow OSHA
(or other local, State, or Federal)
guidelines for exposure to airborne
crystalline silica.
 Know the work operations where
exposure to crystalline silica may
occur.
 Participate in air monitoring or
training programs offered by the
employer.
 Be aware of and use optional
equipment controls such as water
sprays, local exhaust ventilation,
and enclosed cabs with positive
pressure air conditioning if the
machine has such equipment.
Otherwise respirators shall be worn.
 Where respirators are required, wear
a respirator approved for protection
against crystalline silica containing
dust. Do not alter respirator in any
way. Workers who use tight-fitting
respirators can not have beards/
mustaches which interfere with the
respirator seal to the face.
 If possible, change into disposable
or washable work clothes at the
work site; shower and change into
clean clothing before leaving the
work site.
 Do not eat, drink, use tobacco
products, or apply cosmetics in
areas where there is dust containing
crystalline silica.
 Store food, drink, and personal
belongings away from the work
area.
 Wash hands and face before eating,
drinking, smoking, or applying
cosmetics after leaving the exposure
area.
Handle
Chemicals Properly
 Protective clothing should be
worn.
 Handle all chemicals with care.
 Follow instructions on container
label.
 Agricultural chemicals can be
dangerous. Improper use can
seriously injure persons, animals,
plants, soil, and property.
 Inhaling smoke from any type of
chemical fire can be a serious
health hazard.
 Store or dispose of unused
chemicals as specified by the
chemical manufacturer.
4
6/13/19
Important Safety Information
This page left blank intentionally.
6/13/19
5
Table of Contents
Important Safety Information
Important Safety Information
Safety Labels
Your Cold Planer comes equipped with all safety labels in
place. They are designed to help you safely operate your
attachment. Read and follow their directions.
1. Keep all safety labels clean and legible.
2. Refer to this section for proper label placement. Replace
all damaged or missing labels. Order new labels from your
nearest Kubota dealer. To find your nearest dealer, visit
our dealer locator at www.landpride.com.
3.
4.
Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
specified by Kubota. When ordering new components make
sure the correct safety labels are included in the request.
Refer to this section for proper label placement.
To install new labels:
a. Clean surface area where label is to be placed.
b. Spray soapy water onto the cleaned area.
c. Peel backing from label and press label firmly onto the
surface.
d. Squeeze out air bubbles with edge of a credit card or
with a similar type of straight edge.
818-798C
818-798C
Warning: Pinch Point Hazard (3 places)
Models CP3012LF & CP3016LF
Warning: Pinch Point Hazard (3 - places)
Models CP3018, CP3024, CP3030, CP3040, & CP3048
6
72082
72083
72086
72083
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Important Safety Information
858-772C
858-772C
Danger: Rotating Parts Hazard (2 places)
Models CP3012LF & CP3016LF
Danger: Rotating Parts Hazard (2 places)
Models CP3018, CP3024, CP3030, CP3040, & CP3048
72082
72083
72086
72087
6/13/19
AP-CP30 Series Cold Planer 350-376MK
7
Table of Contents
Important Safety Information
838-094C
838-094C
Warning: High Pressure Fluid Hazard (1 place)
Models CP3012LF & CP3016LF
Warning: High Pressure Fluid Hazard (2 places)
Models CP3018, CP3024, CP3030, CP3040, & CP3048
72082
72083
72087
8
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Important Safety Information
844-046C
844-046C
Warning: Thrown Object Hazard (3 places)
Models CP3012LF & CP3016LF
Warning: Thrown Object Hazard (3 places)
Models CP3018, CP3024, CP3030, CP3040, & CP3048
72082
72083
72087
72086
72087
6/13/19
AP-CP30 Series Cold Planer 350-376MK
9
Table of Contents
Important Safety Information
72086
Models CP3012LF & CP3016LF
72087
848-392C
Warning: Flying Objects and Dust Hazard (1 place)
Models CP3018, CP3024, CP3030, CP3040, & CP3048
72086
Models CP3012LF & CP3016LF
72087
838-293C
Warning: Read Operator’s Manual (1 place)
Models CP3018, CP3024, CP3030, CP3040, & CP3048
10
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Important Safety Information
72082
Models CP3012LF & CP3016LF
72083
844-124C
Warning: Silica Dust Hazard (1 Place)
Models CP3018, CP3024, CP3030, CP3040, & CP3048
6/13/19
AP-CP30 Series Cold Planer 350-376MK
11
Table of Contents
Introduction
Introduction
Kubota welcomes you to the growing family of new
product owners. This Cold Planer has been designed
with care and built by skilled workers using quality
materials. Proper assembly, maintenance, and safe
operating practices will help you get years of satisfactory
use from this product.
Terminology
Application
The Online Warranty Registration should be completed
by the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
Kubota’s CP30 Series Cold Planers are hydraulically
powered attachments intended for milling asphalt or light
grinding of concrete surfaces with uses and applications
around streets, parking lots, driveways, construction sites,
municipalities, parks, and universities.
The Low-Flow Cold Planer Models are offered in
12" (31 cm) and 16" (41 cm) widths and are powered by
a hydraulic motor capable of handling up to 25 gpm
(94.6 Lpm). They can cut up to 5" (13 cm) deep,
tilt ± 15 degrees, and sideshift 26" (66 cm). Depth and tilt
control are manually operated, while sideshift is
hydraulically controlled.
The High-Flow Cold Planer Models are available in widths
of 18", 24", 30", 40", and 48" (46, 61, 76, 102, and 122 cm)
with a hydraulic-driven planetary gearbox drive that
provides maximum cutting torque while under load. The
High-Flow Cold Planers can cut up to 6" deep and sideshift
26" (66 cm) and can handle up to 42 gpm (159 Lpm). Tilt
varies from planer to planer (see page 34 for amount of tilt
your model is capable of producing). Included with the
high-flow models is an electro-hydraulic control harness
for controlling depth of cut. Tilt and sideshift are also
electro-hydraulic controlled. However, the operator will
need to dismount to switch the function between tilt and
sideshift at the solenoid valve.
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Owner Assistance
The parts on your Cold Planer have been specially
designed by Kubota/Land Pride and should only be
replaced with genuine Kubota parts. Contact a Kubota
dealer if customer service or repair parts are required.
Your Kubota dealer has trained personnel, repair parts,
and equipment needed to service this implement.
Serial Number
For quick reference and prompt service, record model
and serial number on the inside cover page and again on
the warranty page. Always provide model number and
serial number when ordering parts and in all
correspondences with your Kubota dealer. For location of
your serial number plate, see Figure 1.
72086
See “Specifications & Capacities” on page 34 and
“Features & Benefits” on page 35 for additional
information and performance enhancing options.
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual, contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge, from our website at
www.landpride.com
Definitions
IMPORTANT: A special point of information related
to the following topic. Kubota’s intention is this
information must be read & noted before continuing.
NOTE: A special point of information that the
operator should be aware of before continuing.
12
AP-CP30 Series Cold Planer 350-376MK
CP30 Series Serial Number Plate
Figure 1
Further Assistance
Your dealer wants you to be satisfied with your new
attachment. If for any reason you do not understand any
part of this manual or are not satisfied with the service
received, the following actions are suggested:
1.
Discuss any problems you have with your attachment
with your dealership service personnel so they can
address the problem.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
question/problem, and request assistance.
3. For further assistance write to:
Kubota by Land Pride
Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
[email protected]
6/13/19
Table of Contents
Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
Skid Steer Requirements
The Cold Planer is designed to attach to Kubota skid
steers and track loaders within the following
requirements:
Hitch type. . . . . . . Skid steer quick attach, ISO 24410
Horsepower requirements . . . . . . . . . . . . Max 100 hp
Hydraulic flow rates
3012LF & 3016LF . . . . . . . . 15-25 gpm (57-95 Lpm)
3018 . . . . . . . . . . . . . . . . . 24-42 gpm (91-159 Lpm)
3024 . . . . . . . . . . . . . . . . 27-42 gpm (102-159 Lpm)
3030, 3040, & 3048. . . . . 30-42 gpm (114-159 Lpm)
Min. hydraulic pressure
3012LF, 3016LF, 3018, & 3024. 2000 psi (13.8 MPa)
3040 . . . . . . . . . . . . . . . . . . . . 3000 psi (20.7 MPa)
3048 . . . . . . . . . . . . . . . . . . . . 3500 psi (24.1 MPa)
Max. hydraulic pressure
3012LF & 3016LF . . . . . . . . . . 3500 psi (24.1 MPa)
3018/24/30/40/48 . . . . . . . . . . 5000 psi (34.5 MPa)
Case Drain
3012LF & 3016LF . . . . . . . . . . . . . . . .Not Required
3018/24/30/40/48 . . . . . . . . . . . . . . . . . . . Required
Skid steer weight . . . . . . . . . . . . . See Warning below
!
Make sure the intended skid steer conforms to the “Skid
Steer Requirements” stated above. Read and
understand the operator’s manual for your Cold Planer.
An understanding of how it works will aid in the assembly
and setup of your planer.
Go through the “Pre-Assembly Checklist” below before
assembling the Cold Planer. Speed up your assembly
task and make the job safer by having all needed parts
and equipment readily at hand.
Pre-Assembly Checklist

•
Lightweight power machines may need weight added to the
rear to maintain steering control and prevent forward
tipping or side tipping caused by a heavy front load. Consult
your power machine Operator’s Manual to determine
proper weight requirements and maximum weight
limitations.
Torque Requirements
Refer to “Torque Values Chart” on page 37 to determine
correct torque values when tightening hardware.
Before You Start
! WARNING
To avoid serious injury or death:
•
Allow only persons to operate this attachment who have
fully read and comprehended this manual, who are properly
trained to operate the attachment safely, and who are age 16
or older. Serious injury or death can result from the failure
to read, understand, and follow instructions provided in this
manual.
6/13/19
Make sure all major components and loose
parts are shipped with the attachment.
Operator’s
Manual
Double check to make sure all parts, fasteners
and pins are installed in the correct location to
lessen the chance of using a bolt incorrectly,
Refer to the Parts Manual if unsure.
Operator’s
Manual
350-376MK
NOTE: All assembled hardware from the
factory has been installed in the correct
location. Remember location of a part or
fastener if removed. Keep parts separated.
WARNING
Power machines outside the listed horsepower range must
not be used. Higher horsepower machines can damage the
attachment. Under horsepower machines make the job more
difficult.
Reference
Have a minimum of two people available during assembly.
To avoid serious injury or death:
• Consult your power machine’s manual for operating
capacity, lifting capacity, and operating specifications.
Exceeding rated capacities and specifications can result in
a roll-over or other serious hazard.
•
Check
Have a fork lift or loader with properly sized chains and safety
stands capable of lifting and supporting the equipment on hand.
Make sure working parts move freely, bolts are
tight & cotter pins are spread.
Parts Manual
350-376PK
Operator’s
Manual
Make sure all grease fittings are in place and
lubricated.
Page 30
Make sure all safety labels are correctly
located and legible. Replace if damaged.
Page 6
Skid Steer Shutdown Procedure
The following are basic skid steer shutdown procedures.
Follow these procedures and any additional shutdown
procedures provided in your skid steer Operator’s
Manual before leaving the operator’s seat.
1.
Reduce engine speed and shut-off all power to the
attachment.
2. Park on solid, level ground and lower attachment until
it is flat on the ground or on non-concrete support
blocks.
3. Turn off engine, and remove switch key to prevent
unauthorized starting.
4. Relieve all hydraulic pressure to auxiliary hydraulic
lines.
5. If included, raise seat bar and move controls until
both lock.
6. Wait for all components to come to a complete stop
before leaving the operator’s seat.
7.
Use steps, grab-handles and anti-slip surfaces when
stepping on and off the skid steer or attachment.
AP-CP30 Series Cold Planer 350-376MK
13
Table of Contents
Section 1: Assembly & Set-up
Dealer Set-up
72090
Refer to Figure 1-1 & Figure 1-2:
The Cold Planer is shipped from the factory fully
assembled. Use a hoist or other suitable lift device to lift
the unit off the pallet and set it on the ground. Make sure
the Cold Planer is secured before lifting it.
Use lift holes on both sides of the planer shown in
Figure 1-1 to pick up the Low Flow Cold Planers (Models
CP3012LF or CP3016LF).
Use lift lugs on both sides of the planer shown in
Figure 1-2 to pick up the High-Flow Cold Planers (Models
CP3018, CP3024, CP3030, CP3040, or CP3048).
Preform the following simple checks before operation
begins.
Safety Decals
Refer to pages 6-11:
The safety decals should be clearly readable and always
followed. Replace any decal that is missing or not
readable. Refer to “Safety Labels” on page 6.
Low-Flow Cold Planer Set-up
The following checks are for Models CP3012LF and
CP3016LF. If the Cold Planer is not one of these two
models, skip to “High-Flow Cold Planer Set-up” on
page 15.
Low-Flow Planer Lift Points (Typical on Both Sides)
Figure 1-1
72091
Hydraulic Couplers
The hydraulic hoses on the Low-Flow Cold Planer are
shipped with couplers. If the couplers do not fit the skid
steer couplers, the customer will need to obtain the
correct style and size to match the skid steer couplers
and planer hydraulic hoses.
The planers operate on the skid steer auxiliary hydraulic
flow. Since the auxiliary flow is reversible, be sure to
operate the unit so the drum is spinning in the direction
the teeth are pointing.
Hydraulic Hoses and Fittings
All fittings should be tight and free of hydraulic leaks.
Hoses must be free of abrasion or cuts that might result
in leakage. Check your attachment before operation to
make sure all hose routings are kink-free and allow for
maximum movement of loader arms and tilt motion
required during normal operation.
Drum Assembly
For proper drum operation, picks must be installed in
every pick holder on the drum.
14
AP-CP30 Series Cold Planer 350-376MK
High-Flow Planer Lift Points (Typical on Both Sides)
Figure 1-2
6/13/19
Table of Contents
Section 1: Assembly & Set-up
High-Flow Cold Planer Set-up
The following checks are for Models CP3018, CP3024,
CP3030, CP3040, and CP3048. If the Cold Planer is not
one of these five models, Refer to “Low-Flow Cold
Planer Set-up” on page 14.
Hydraulic Couplers
The hydraulic hoses on the High-Flow Cold Planer are
shipped with couplers. If the couplers do not fit the skid
steer couplers, the customer will need to obtain the
correct style and size to match the skid steer couplers
and planer hydraulic hoses.
The pressure “in” port on the diverter valve is marked LP
for motor pressure. Return flow to the loader is marked
LR for motor return. The small hose is for the drive motor
case drain and is connected directly to the skid steer
case drain coupler.
The case drain hose should be connected directly to the
case drain coupler on the skid steer.
Hoses and Fittings
All fittings should be tight and free of hydraulic leaks.
Hoses must be free of abrasion or cuts that might result
in leakage. Check your attachment before operation to
make sure all hose routings are kink-free and allow for
maximum movement of loader arm and tilt motion
required during normal operation.
Wire Harness
The wiring harness to the electro-hydraulic valve block
should be routed to prevent catching or pinching when
sideshifting, tilting, or lowering the drum fully into the cut.
Drum Assembly
For proper drum operation, picks must be installed in
every pick holder on the drum.
6/13/19
Motor Case Drain
IMPORTANT: Do not operate the Cold Planer
without connecting the case drain hose to the skid
steer’s case drain coupler. Not connecting case
drain coupler may cause severe damage to the
hydraulic motor.
IMPORTANT: Unobstructed case drain flow is
critical to proper motor operation. Blocked case
drain flow will damage the hydraulic motor.
NOTE: Unless a defect in the motor is found,
damage to the motor shaft seal and end cap gasket
are not covered under the warranty.
The High-Flow Cold Planers have a planetary gearbox
mounted with the drum which is driven by a hydraulic
piston motor.
During motor operation, some oil bypasses the motor
and must be allowed an unobstructed path back to the
skid steer hydraulic tank. If this flow is restricted,
pressure will build up inside the motor and will damage
the motor shaft seals and/or end cap gasket.
Several cases can lead to this damage:
• Pinched or crushed case drain hose can restrict flow.
• Disconnected case drain quick coupler will stop flow.
• Picks on the cutting drum can come in contact with the
pavement or trailer ramps while the skid steer is in
motion, forcing the drum to rotate with the high-flow
hydraulic circuit “off”. This drum rotation forces the
motor to turn, which pressurizes the motor’s case
because the pressure and return oil’s path have been
blocked.
If the above issues are not addressed, severe motor
damage may result. All of these issues can be attributed
to the operator and are preventable with proper
operation. Never operate Cold Planer without ensuring
the case drain hose is in good working order and properly
connected.
AP-CP30 Series Cold Planer 350-376MK
15
Table of Contents
Section 2: Operating Procedures
Section 2: Operating Procedures
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the Cold Planer. Therefore, it is
absolutely essential that no one operates the Cold
Planer unless they are age 16 or older and have read,
fully understood, and are totally familiar with the
Operator’s Manual and equipment work site.
•
Do not let children play on or around the attachment
including when stored. Children and/or attachment can fall.
•
Do not allow anyone near the power machine or attachment
while operating. Stop operation if bystanders are too close.
They can be hit by flying projectiles or become entangled,
crushed, or ran over by the equipment.
•
Perform the following inspections before using your Cold
Planer.
Do not drive close to ditches, retaining walls, drop-offs,
water, etc. Rollover due to a cave-in or mishap could result.
•
Know weight limitations of operating surfaces and
clearances.
Operating Checklist

Check
Read & follow all safety rules & safety decals.
Refer to this manual and the attachment’s decals.
Make sure all guards and shields are in place.
Read & follow preparation & setup instructions.
Refer to “Section 1: Assembly & Set-up”.
Read and follow all operating procedures.
Refer to “Section 2: Operating Procedures”.
Read & follow all maintenance Instructions.
Refer to “Section 4: Maintenance & Lubrication”.
Read & follow all lubrication instructions.
Refer to “Lubrication Points”.
Check initially and periodically for loose bolts and
pins. Refer to “Torque Values Chart”.
!
Page
13
16
27
•
Refer to the safety section of your skid steer Operator’s
Manual and observe all safety recommendations set forth in
the manual.
•
Use steps, grab-handles, and anti-slip surfaces on the
power machine and attachment to get on and off the power
machine. Using unapproved stepping surfaces and/or
handholds can result in a falling hazard.
•
Allow only persons to operate this attachment who have
fully read and comprehended this manual, who are properly
trained to operate the attachment safely, and who are age 16
or older. Serious injury or death can result from the failure
to read, understand, and follow instructions provided in this
manual.
•
Operate only power machines equipped with a certified
Roll-Over Protective Structure (ROPS) and seat belt.
Fasten seat belt snugly and securely to help protect against
serious injury or death from machine overturn.
•
Backup alarm must be in good working order to warn
others. Use a backup camera or rear-view mirror that is in
good condition to help see undesirable situations behind the
unit. Drive at a slower speed to compensate for blind spots.
•
Operate attachment from inside an enclosed cab or wear a
dust mask and eye protection. Flying dust and debris can
enter the lungs causing respiratory problems, enter the eyes
causing eye injury and /or cause bodily injury to the body of
people or animals.
•
Avoid exposure to dust containing crystalline silica
particles. This dust can cause serious injury to the lungs
(silicosis). Because crystalline silica is a basic component
of sand and granite, many activities at construction sites
produce dust containing crystalline silica. Trenching,
sawing, and boring of material containing crystalline silica
can produce dust containing crystalline silica.
•
Make sure controls are all in neutral position or park before
starting the power machine.
•
Always operate attachment while seated with seat belt
properly fastened around the operator. When equipped,
always lower seat/lap bar(s). This will help protect the
operator against rollovers and sudden stops.
30
37
General Safety Information
Exposed moving parts are guarded whenever possible
for safety. However, not all moving parts can be shielded
in order to ensure proper operation. This Operator’s
Manual and safety decals on the machine provide
important safety information. Read and follow their
directions. If a safety decal becomes difficult to read,
replace it immediately.
!
DANGER
To avoid serious injury or death:
• Never crawl under raised loader arms unless properly
secured. Fully lower loader arms or have the loader arms
secured in the raised position with an approved lift-arm
support before leaving the skid steer seat. Crawling under
unsupported loader arms can cause a crushing hazard.
•
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment
supported by concrete blocks or hydraulics. Concrete can
break, hydraulic lines can burst, and/or hydraulic controls
can be actuated even when power to hydraulics is off.
•
Keep body, body extremities, clothing, pull strings, etc.
away from rotating/moving parts. Always shut off
hydraulics to the attachment and shutdown the power
machine before adjusting or servicing the equipment.
•
All guards and shields must be installed and in good
working condition while operating the attachment. Never
operate planer with drum door open.
16
AP-CP30 Series Cold Planer 350-376MK
WARNING
To avoid serious injury or death:
• Make sure safety labels are installed in their proper
location and are in good condition before operating the
attachment. Read and obey all instructions on the labels.
6/13/19
Table of Contents
Section 2: Operating Procedures
•
Never carry riders on the attachment or power machine.
Riders can obstruct the operator’s view, interfere with
control of the equipment, be pinched by moving
components, become entangled in rotating components, be
struck by objects, be thrown or fall from the equipment, etc.
•
Always shut power machine down using the “Shutdown
Procedure” provided in this manual before servicing,
adjusting, cleaning, or maintaining the attachment.
•
Never allow hands or feet near any working part of the
attachment unless the mandatory power machine shutdown
procedure has been completed.
•
Check hitch fit-up frequently. An improper fit-up can cause
the attachment to come loose from the loader hitch plate
and fall.
•
•
Never make contact with underground utilities such as
electrical power lines, gas lines, phone lines, etc. They can
cause serious injury or death from electrocution, explosion,
or fire. If in doubt, call 811 (USA) before digging so that
they can mark the location of underground services in the
area. For contact information, see Dig Safe in the
“Important Safety Information” starting on page 1.
Always exercise safety, courtesy, and common sense. Be
aware of pedestrian and vehicle traffic. Check blind spots
before moving. Use Cold Planer during low-traffic hours.
•
Do not use attachment to lift, carry, push or tow other
equipment and objects. It is not properly designed or
guarded for this use. The operator could lose control and
cause a tipping hazard.
•
Keep body, body extremities, loose clothing, pull strings,
etc. away from pinch points such as rotating, extending,
and/or retracting components. Secure pinch point areas to
ensure they will not move before working on or near them.
•
Do not alter attachment or replace parts on the attachment
with other brands. Other brands may not fit properly or
meet OEM specifications. They can weaken the integrity
and impair the safety, function, performance, and life of the
attachment. Replace parts only with genuine OEM parts.
•
Bottom Slot
Top Angle Bar
Do not grind anything other than asphalt or light concrete.
Doing so can cause a thrown object hazard or damage the
Cold Planer.
•
•
70986
Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting the
attachment back into service. Serious breakdowns can
result in injury or death.
Hydraulic fluid under high pressure can penetrate the skin
and/or eyes causing a serious injury. Wear protective gloves
and safety glasses or goggles when working with hydraulic
systems. Use a piece of cardboard or wood rather than
hands when searching for leaks. A doctor familiar with this
type of injury must treat the injury within a few hours or
gangrene may result. DO NOT DELAY.
Bottom Slot
Hook-up Cold Planer
Figure 2-1
Hook-up Cold Planer
Refer to Figure 2-1:
!
DANGER
!
WARNING
To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking the
attachment. Do not allow anyone to stand between attachment
and power machine while approaching or backing away from
the attachment. Do not operate lift and/or tilt controls while
someone is near the power machine and/or attachment.
To avoid serious injury or death:
• Check hitch fit-up frequently. An improper fit-up can cause
the attachment to come loose from the loader hitch plate
and fall.
•
Use steps, grab-handles, and anti-slip surfaces on the
power machine and attachment to get on and off the power
machine. Using unapproved stepping surfaces and/or
handholds can result in a falling hazard.
1.
Check skid steer and Cold Planer hitch plates before
hooking-up the planer. Make sure all hitch
components are in good working condition:
a. Check for and remove any debris in the loader
and planer hitch plates.
b. Check hitch plates for structural cracks and bent
or broken pieces. They can weaken a hitch plate
and prevent full and complete hook-up. Repair or
replace damaged hitch plates before putting the
Cold Planer into service.
c. Check operation of lock pins in the loader hitch
plate. Lock pins must move freely and extend fully
into the bottom slots in the planer hitch plate.
d. Check hydraulic hoses for pinch points and
clearances. Make sure hydraulic hoses will not
interfere with hitch hook-up.
6/13/19
AP-CP30 Series Cold Planer 350-376MK
17
Table of Contents
Section 2: Operating Procedures
2. If lock mechanism is mechanical, raise lock handles
on the loader hitch plate fully up to raise lock pins.
3. Start skid steer.
!
WARNING
6. Tilt top of loader hitch plate slightly forward.
To avoid serious injury or death:
• Hydraulic fluid under high pressure can penetrate the skin
and/or eyes causing a serious injury. Wear protective gloves
and safety glasses or goggles when working with hydraulic
systems. Use a piece of cardboard or wood rather than
hands when searching for leaks. A doctor familiar with this
type of injury must treat the injury within a few hours or
gangrene may result. DO NOT DELAY.
7.
•
Shut power machine down and release all hydraulic
pressure to the equipment before connecting or
disconnecting hydraulic hoses to or from the power
machine.
•
Make sure hydraulic flow to the Cold Planer does not
exceed maximum rated flow listed in the specifications on
page 34. Exceeding maximum flow will increase rotor speed
and result in a thrown object hazard.
4. If lock mechanism is hydraulic, use auxiliary
hydraulic controls to raise lock pins fully up.
5. Drive slowly to the planer hitch plate while making
sure the loader hitch is parallel with the top angle bar
on the cold Planer hitch plate.
Place top of loader hitch plate under the Cold Planer
top angled bar and slowly raise loader arms up until
loader hitch plate is seated under the top angle bar.
8. Tilt top of loader hitch plate back until planer hitch
plate makes full contact with loader hitch plate and
the Cold Planer is slightly off the ground.
9. Engage lock mechanism:
Hydraulic Lock Mechanism:
a. Engage quick hitch locking mechanism
hydraulically.
IMPORTANT: Make sure coupler fittings are clean
before making connections. Dirt can quickly damage
the hydraulic system. Inspect couplers for corrosion,
cracks and excessive wear. Replace couplers if any
of these conditions exist.
Mechanical Lock Mechanism:
a. Shut skid steer down before dismounting.
Refer to “Skid Steer Shutdown Procedure” on
page 13.
b. Push lock handles down to drive lock pins through
bottom slots in the planer hitch plate. Make sure
handles are locked down.
c. Return to skid steer and start.
10. Raise loader arms enough to visually ensure lock
pins are through the bottom slots on the Cold Planer.
11. Shut skid steer down before dismounting. Refer to
“Skid Steer Shutdown Procedure” on page 13.
Hydraulic Hose Hook-up
IMPORTANT: All hoses should be free of kinks, cuts,
or abrasions for safe operation. Do not operate if
hoses are worn or damaged.
1.
Clean quick connect couplers of dirt and then
connect female and male coupler to the skid steer’s
auxiliary outlets. Make sure quick connect couplers
have fully engaged. If they have not, check the
following to make sure:
a. Couplers are same size and type.
b. Auxiliary hydraulic pressure to the loader couplers
has been released.
NOTE: A case drain line with coupler is included
only for High-Flow Cold Planers with a planetary
gearbox.
2. If hooking-up a High-Flow Cold Planer, hook-up case
drain hydraulic hose coupler to the skid steer’s case
drain coupler.
3. Refer to Figure 2-2 on page 19 for the low-flow
hydraulic schematic and Figure 2-3 on page 19 for
the high-flow hydraulic schematic.
4. For additional help, refer to Hydraulic Hook-up in
your skid steer Operator’s Manual.
18
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Section 2: Operating Procedures
72154
Low-Flow Hydraulic Schematic
Figure 2-2
72153
High-Flow Hydraulic Schematic
Figure 2-3
6/13/19
AP-CP30 Series Cold Planer 350-376MK
19
Table of Contents
Section 2: Operating Procedures
72151
CONNECT TO WHITE WIRE
ON WIRE HARNESS #106-6340
CONNECT TO ORANGE WIRE
ON WIRE HARNESS #106-6340
CONNECT TO RED WIRE
ON WIRE HARNESS #106-6340
CONNECT TO BLUE WIRE
ON WIRE HARNESS #106-6340
CONNECT TO GREEN WIRE
ON WIRE HARNESS #106-6340
CONNECT TO BROWN WIRE
ON WIRE HARNESS #106-6340
High-Flow Solenoid Valve Part No. 106-6330
Figure 2-4
Electrical Hook-up
Refer to Figure 2-4 above & “Figure 2-5” on this page
1. Attach adapter wire harness #106-6340 to solenoid
valve #106-6330. Make sure wire colors are matched
with the stated color for each connector on the valve.
2. Adapter wire harness #106-6430 is factory installed
to back of toggle switch #106-6339
Refer to Figure 2-6 & Figure 2-7 on page 21:
3. Attach main wire harness #106-0647 to adapter wire
harness #106-6340. Make sure wire colors are
matched at each connection.
72653
#106-6340 Harness
connections to switch.
a2: YELLOW
a3: LIGHT BROWN
a4: GRAY
b2: ORANGE
b3: BROWN
b4: PURPLE
Back of Rocker Switch Part #106-6339
Figure 2-5
4. Rout main wire harness through the spring hose loop
and connect it to the skid steer pin connector.
5. Make sure the main wire harness is routed to prevent
it from catching or pinching while sideshifting, tilting
the drum, tilting the hitch plate, or lowering the drum
fully into the cut.
20
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Section 2: Operating Procedures
72161
DIODE PACK A
#106-6341
DIODE PACK B
#106-6342
DEUTSCH
#DT06-12SA
DEUTSCH
#DT04-12PA
DEUTSCH
#DT04-2P
DEUTSCH
#DT06-12SA
LEFT DEPTH UP
DARK-BLUE WIRE
WITH BLUE ZIP TIE
DEUTSCH
#DT04-12PA
DEUTSCH DT06-2S
W/ WHITE WIRE
DEUTSCH DT06-2S
W/ RED WIRE
LEFT DEPTH DOWN
LIGHT-BLUE WIRE
WITH Orange ZIP TIE
RIGHT DEPTH UP
DARK-GREEN WIRE
WITH GREEN ZIP TIE
DEUTSCH DT06-2S
W/ BLUE WIRE
RIGHT DEPTH DOWN
LIGHT-GREEN WIRE
WITH YELLOW ZIP TIE
DEUTSCH DT06-2S
W/ GREEN WIRE
TILT CW & SIDESHIFT
DARK-BROWN WIRE
WITH BROWN ZIP TIE
DEUTSCH DT06-2S
W/ BROWN WIRE
TILT CCW & SIDESHIFT
LIGHT-BROWN WIRE
WITH WHITE ZIP TIE
DEUTSCH DT06-2S
W/ ORANAGE WIRE
1/4" FULLY INSULATED QD TERMINALS
Connects to Wire Harness #106-0647
Connects to Switch #106-6339
Connects to Solenoid Valve #106-6330
High-Flow Adapter Wire Harness #106-6340
Figure 2-6
72152
DT06-2S Connects to Adapter Harness #106-6340
DEPTH UP
DARK-BLUE WIRE
LABEL: C1A
HDR36-18-14SN-059
DARK BLUE
DT06-2S
LIGHT BLUE
DARK GREEN
DEPTH DOWN
LIGHT-BLUE WIRE
LABEL: C1B
LIGHT GREEN
DT06-2S
DARK BROWN
LIGHT BROWN
TILT LEFT
DARK-GREEN WIRE
LABEL: C2A
F-DEPTH DN
C-TILT LEFT
D-TILT RIGHT
G-SIDESHIFT LEFT
H-SIDESHIFT RIGHT
A-NOT USED
DT06-2S
J-NOT USED
BLACK
TILT RIGHT
LIGHT-GREEN WIRE
LABEL: C2B
E-DEPTH UP
B-GROUND
K-NOT USED
DT06-2S
L-NOT USED
M-NOT USED
N-NOT USED
SIDESHIFT LEFT
DARK-BROWN WIRE
LABEL: C3A
DT06-2S
SIDESHIFT RIGHT
LIGHT-BROWN WIRE
LABEL: C3B
DT06-2S
P-NOT USED
High-Flow Electrical Schematic for Main Wire Harness Part #106-0647
Figure 2-7
6/13/19
AP-CP30 Series Cold Planer 350-376MK
21
Table of Contents
Section 2: Operating Procedures
Pre-Operation Inspection
Check Equipment Clearances
1.
It is important to check equipment clearances and
hydraulic hose routing before putting the Cold Planer into
operation. Carefully go through the planer’s full range of
motions to make sure the planer does not make contact
with the skid steer frame, tires, and hydraulic hoses.
Check hydraulic hoses to make sure they do not stretch,
kink, or pinch.
Shut skid steer and Cold Planer down. Follow “Skid
Steer Shutdown Procedure” on page 13.
2. Complete “Operating Checklist” on page 16.
3. Inspect attachment’s safety equipment to make sure
it is in good working condition and that all safety alert
decals are visible and legible. Replace all missing
and/or illegible safety alert decals. See “Safety
Labels” on page 6.
4. Check skid steer and Cold Planer hitch plates. Make
sure all hitch components are in good working
condition:
a. Check for and remove any debris in the loader
and Cold Planer hitch plates.
b. Check hitch plates for structural cracks that can
weaken the hitch plates and result in dropping the
attachment. Check for bent plates that will prevent
full and complete hook-up. Repair or replace
damaged hitch plates before putting the Cold
Planer into service.
!
•
Check hitch fit-up frequently. An improper fit-up can cause
the attachment to come loose from the loader hitch plate
and fall.
1.
Before starting the skid steer, check hitch hook-up.
The attachment can fall from the loader hitch plate if
not properly connected.
c. Check operation of lock pins in the loader hitch
plate. Lock pins must move freely and extend fully
into the bottom slots in the Cold Planer hitch plate.
a. Make sure loader hitch is fully seated under the
Cold Planer’s top angle bar.
d. Check hydraulic hoses for pinch points and
clearances. Make sure hydraulic hoses will not
interfere with hitch hook-up.
5. If attachment is to be operated in reverse, make sure
visibility to the rear of the power unit is appropriate for
the attachment. Backup camera or mirror is
recommended. Maintain cleanliness of lens or
mirror.
6. Consult your skid steer Operator’s Manual to
determine if rear ballast is required. Add ballast if
necessary.
7.
Visually check for excessive wear, worn, damaged,
cracked, or loose parts. Replace parts with genuine
Kubota parts.
8. Inspect condition of hydraulic hoses, fittings, and
valves before starting the skid steer. Make sure
hoses are not twisted or frayed and will not get
pinched, kinked, or stretched.
9. Start skid steer and check hydraulic oil leaks with a
piece of paper or cardboard. Do not use your hands
as invisible thin streams of high pressure oil can be
injected into your skin. See “Avoid High Pressure
Fluids Hazard” on page 3.
10. Check all controls and operating functions of the skid
steer.
11. Operate the Cold Planer through its full range of
movements to check for clearances. Refer to “Check
Equipment Clearances” on this page.
22
AP-CP30 Series Cold Planer 350-376MK
WARNING
To avoid serious injury or death:
• Use steps, grab-handles, and anti-slip surfaces on the
power machine and attachment to get on and off the power
machine. Using unapproved stepping surfaces and/or
handholds can result in a falling hazard.
b. Make sure loader hitch plate is against the Cold
Planer hitch plate.
c. Make sure lock handles or hydraulic locks are
locked with lock pins fully seated in the bottom
slots.
2. If necessary, have someone stand nearby but at a
safe distance that can motion for the operator to stop
if a problem develops.
3. With the Cold Planer on the ground, start skid steer
and carefully rotate the top of the loader hitch plate
fully back while watching hydraulic hoses to make
sure they do not become pinched or kinked.
4. Carefully raise loader arms up while tilting the top of
the hitch fully forward to rotate the front of the Cold
Planer down. Watch hydraulic hoses to make sure
they do not stretch, pinch, or kink.
5. Continue to raise loader arms fully up and tilt the
loader hitch fully forward while watching to make sure
the attachment does not make contact with the skid
steer or skid tires. Watch hydraulic hoses to make
sure they do not stretch, pinch, or kink.
6. Rotate top of hitch plate back and lower loader arms
until Cold Planer is resting on the ground.
7.
Shut skid steer down before dismounting. Refer to
“Skid Steer Shutdown Procedure” on page 13.
8. Recheck hydraulic hoses. If needed, add zip ties to
the hoses to protect them from possible damage.
6/13/19
Table of Contents
Section 2: Operating Procedures
72123
72107
8
Sideshift/Drum Toggle Lever
Figure 2-8
Basic Operation
IMPORTANT: Insufficient hydraulic power will result
in poor performance. Check pressure and flow per
factory skid steer specifications.
NOTE: Milling speed will depend on pick condition,
age and density of the material, aggregate size, and
ambient temperature.
Before operating the attachment, read this entire manual.
Follow all safety guidelines in this manual and safety
decals on the unit. Make sure that all guards, shields, and
decals are in place and in good condition prior to
operation.
See specifications in this manual for minimum and
maximum pressures and flow requirements for your
machine. Make sure the skid steer hydraulic pressure
ratings fall within the specified range.
Low-Flow Cold Planers
Figure 2-9
Operating the Low-Flow Cold Planer
Refer to Figure 2-9:
1. Enter skid steer and fasten seat belt.
2. Make sure the area is clear of all bystanders, start
skid steer, and set engine at an idle.
3. Lower loader arms fully down, tilt top of hitch plate
fully back, shut skid steer down without changing
hitch plate tilt. Refer to“Skid Steer Shutdown
Procedure” on page 13.
4. Dismount skid steer to make the following
adjustments:
a. Loosen wing screw (#1) and manually adjust tilt
jack (#2) to the preferred angle using angle
gauge (#3) as a guide. Tighten wing screw (#1).
The Cold Planer is a hydraulically powered attachment
intended for milling asphalt or light concrete surfaces.
The performance of the attachment can vary greatly
depending upon how it is used and operated. The
recommended operation procedures in this manual
should be followed at all times for maximum productivity.
Productivity can vary greatly depending on milling depth,
type of aggregate in the mix, ambient temperature, and
condition of the picks.
Picks should be inspected every 30 minutes for wear and
to make sure they are rotating freely in their holders.
Replace worn picks immediately. To promote pick
rotation, spray picks daily with a water based asphalt
emulsifier to break down asphalt emulsion. (Example:
Zep’s part #AR6690) See the maintenance section for
more information.
b. Loosen wing screw (#4) and manually adjust
depth jack (#5) to the preferred depth using depth
gauge (#6) as a guide. Tighten wing screw (#4).
c. Refer to Figure 2-8: If sideshifting the planer,
move toggle lever (#8) to sideshift position.
5. Repeat steps 1-2 above.
IMPORTANT: To prevent damaging the Cold Planer,
raise the unit off the ground before sideshifting.
6. Raise Cold Planer fully off the ground and then
engage hydraulic cylinder (#7) to start sideshifting.
7.
Once at the desired side sift position, disengage
hydraulics and shut skid steer down. See “Skid
Steer Shutdown Procedure” on page 13.
Optional picks for milling concrete and Water Spray Kits
are available. Water Spray Kits increase productivity by
suppression dust and help picks rotate properly.
8. Refer to Figure 2-8: Return toggle lever (#8) to drum
operating position and repeat steps 1-2 above.
If attachment is to be operated in reverse, make sure
visibility to the rear of the power unit is appropriate for the
attachment. Backup camera or mirror is recommended.
Maintain cleanliness of lens or mirror.
9. Raise loader arms until planer drum is off the
surface. Engage hydraulics to the planer and move
throttle to full rpm. Keep throttle at full rpm during
milling operations.
Do not turn while milling. Cut straight lines only. Cutting
curves will quickly wear the picks located along the edge
of the drum and decrease productivity. Milling a radius or
curve can also damage the drum.
10. Lower drum into the cut.
6/13/19
11. Move forward at a speed that will allow the drum to
cut efficiently without stalling.
AP-CP30 Series Cold Planer 350-376MK
23
Table of Contents
Section 2: Operating Procedures
72121
72150
9
High-Flow Cold Planers
Figure 2-10
Operating the High-Flow Cold Planer
Sideshift/Tilt Toggle Switch
Figure 2-11
Refer to Figure 2-10:
1. Enter skid steer and fasten seat belt.
15. Once at the desired tilt position, disengage
hydraulics to the tilt cylinder.
2. Make sure the area is clear of bystanders, start skid
steer, and set engine at an idle.
16. Raise loader arms until the Cold Planer is off the road
surface.
3. Raise planer off the ground just high enough to allow
for the skid shoes to be adjusted.
17. Engage electrical and hydraulic controls to the drum
motor and move throttle to full rpm position. Keep
throttle at full rpm during milling operations.
4. With skid steer operating at an idle, make the
following adjustments using the electrical and
hydraulic controls.
a. Adjust planer depth on the left with cylinder (#1)
while using depth gauge (#2) as a guide.
18. Lower drum into the cut.
19. Move forward at a speed that will allow the drum to
cut efficiently without stalling.
b. Adjust planer depth on the right with cylinder (#3)
while using depth gauge (#4) as a guide.
5. Shut skid steer down before dismounting. Refer
to“Skid Steer Shutdown Procedure” on page 13.
6. Refer to Figure 2-11 on page 24: Dismount and
toggle switch (#9) to the sideshift position.
7.
Repeat steps 1-2 above.
IMPORTANT: To prevent damaging the Cold Planer,
raise the unit off the ground before sideshifting.
8. Raise Cold Planer fully off the ground.
9. Using the electrical and hydraulic controls, engage
hydraulic cylinder (#5) to sideshift the planer.
10. Once at the desired position, disengage hydraulics
and shut skid steer down. See “Skid Steer
Shutdown Procedure” on page 13.
11. Refer to Figure 2-11 on page 24: Reposition toggle
switch (#9) to the tilt position.
12. Repeat steps 1-2 above.
13. Raise attachment off the ground.
14. Using the electrical and hydraulic controls, engage
hydraulics to tilt cylinder (#7). Adjust planer tilt to the
preferred angle using angle gauge (#6) as a guide.
24
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Section 2: Operating Procedures
Transporting
!
WARNING
To avoid serious injury or death:
When traveling on roadways, transport in such a way that
other vehicles may pass you safely. Use accessory lights, clean
reflectors, and a slow moving vehicle sign that is visible from
the back to warn operators in other vehicles of your presence.
Always comply with all federal, state, and local laws.
1.
Be sure to reduce ground speed when turning. Leave
enough clearance to keep the attachment from
making contact with obstacles such as buildings,
trees or fences.
2. Select a safe ground speed when transporting from
one area to another.
Unhook Cold Planer
Refer to “Figure 2-1” on page 17:
1. Park skid steer with Cold Planer on a flat, level
surface. Lower loader arms until Cold Planer is
resting on the ground.
2. Shut skid steer down before dismounting. Follow
“Skid Steer Shutdown Procedure” on page 13.
3. Disconnect hydraulic hoses. It will be necessary to
release hydraulic pressure in the lines before hoses
will disconnect from the skid steer. Coil hydraulic
hoses and store them on the planer with hose ends
out of the dirt.
4. Disconnect wire harness from the skid steer. Coil
wire harness up and store on the planer with the plug
end hanging down to keep moisture and dirt out.
3. When traveling on public roadways, transport in such
a way that faster moving vehicles may pass you
safely. A slow moving vehicle sign should always be
properly displayed when traveling on public roads or
right-of ways.
5. If lock handles are mechanical, pull lock handles up
on the loader hitch plate to remove lock pins from the
bottom slots in the attachment’s hitch plate.
4. Decrease transport speed when traveling over rough
or hilly terrain.
8. If lock handles are hydraulic, raise lock pins
hydraulically to remove them from the hitch plate
slots.
5. When transporting skid steer on a trailer:
• Use towing vehicle and trailer of adequate
capacity.
• Always drive up a ramp with heavy end uphill.
• Shut skid steer down before dismounting. Follow
“Skid Steer Shutdown Procedure” on page 13.
• Secure skid steer loader and attachment using tie
downs and chains.
6/13/19
6. Return to the skid steer seat and fasten seat belt.
7.
Start skid steer.
9. Tilt loader hitch plate slightly forward until the bottom
of the loader hitch plate has separated away from the
bottom of the Cold Planer hitch plate.
10. Slowly lower loader arms until the loader hitch plate
has separated from the attachment’s top angle bars.
11. Back skid steer slowly away from the planer making
sure the skid steer does not interfere with the
attachment’s hitch plate, hydraulic hoses, or wire
harness.
AP-CP30 Series Cold Planer 350-376MK
25
Table of Contents
Section 3: Options & Accessories
Section 3: Options & Accessories
Picks (Accessory)
Water Spray Kit (Accessory)
The factory installed carbide picks are a general purpose
pick and are designed for milling both asphalt and
concrete. Picks designed for extended periods of
concrete milling are available from your dealer.
Use Water Spray Kit provided by Kubota to increase pick
life by 20% to 40% and to suppress milling dust. Water
Spray Kits are available from your dealer. Order 1 Cold
Planer Control Box, 1 Water Tank Kit, and 1 Spray Bar Kit
that matches the Cold Planer model.
Part No.
DescriptionQty
106-3142
Pick, CP30, Asphalt (See Notes 1 & 2)
106-3133
Pick, Concrete (Accessory) See Note 1
Note 1: Factory Installed.
Note 2: Total quantity of picks required per drum varies
from model to model. See Model number and quantities
listed below.
CP3012LF . . 30 ea.
CP3016LF . . 38 ea.
CP3018 . . . . 40 ea.
CP3024 . . . . 50 ea.
CP3030 . . . . 60 ea.
CP3040 . . . . 76 ea.
CP3048 . . . . 96 ea.
26
AP-CP30 Series Cold Planer 350-376MK
Part No.
Description
350-438A
350-378A
350-379A
350-380A
350-381A
350-382A
350-383A
350-384A
350-385A
Cold Planer Control Box
Water Tank Kit, CP30
Spray Bar Kit, CP3012LF
Spray Bar Kit, CP3016LF
Spray Bar Kit, CP3018
Spray Bar Kit, CP3024
Spray Bar Kit, CP3030
Spray Bar Kit, CP3040
Spray Bar Kit, CP3048
6/13/19
Table of Contents
Section 4: Maintenance & Lubrication
Section 4: Maintenance & Lubrication
Maintenance
Proper servicing and adjustment are key to the long life of
any attachment. With careful and systematic inspection,
you can avoid costly maintenance, time, and repair.
Check all bolts after using the unit for several hours to be
sure they are tight. Replace any worn, damaged, or
illegible safety labels by obtaining new labels from your
Kubota dealer.
!
DANGER
To avoid serious injury or death:
• Do not go near or under raised loader arms without first
securing loader arms in the raised position with an
approved lift-arm support.
•
Keep body, body extremities, clothing, pull strings, etc.
away from rotating/moving parts. Always shut off
hydraulics to the attachment and shutdown the power
machine before adjusting or servicing the equipment.
•
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment
supported by concrete blocks or hydraulics. Concrete can
break, hydraulic lines can burst, and/or hydraulic controls
can be actuated even when power to hydraulics is off.
!
WARNING
To avoid serious injury or death:
• Always shut power machine down using the “Shutdown
Procedure” provided in this manual before servicing,
adjusting, cleaning, or maintaining the attachment.
•
Hydraulic fluid heats up when the skid steer is operating.
This can cause hydraulic hoses, fittings, and couplers to
become hot. Wear gloves when working with hydraulic
components and when connecting and disconnecting
hydraulic couplers.
Servicing Drivetrain Components
Detailed repair of the drivetrain components such as the
hydraulic motor and gearbox are not covered in this
manual. Contact your Kubota dealer for information
about repairing these components during the warranty
period.
Any unauthorized work performed on these components
during the warranty period may void your warranty.
Cutting Drum Maintenance
Cutting drum maintenance is critical to extending the life
of the pick, pick holder, and overall productivity of the
planer.
IMPORTANT: Inspect cutting drum picks and
pick holders every 30 minutes of operation.
The factory installed carbide picks are a general purpose
pick and are designed for milling both asphalt and light
concrete. Picks designed for extended periods of
concrete cutting are available from your dealer. Refer to
“Picks (Accessory)” on page 26.
Pick life varies with depth, density, material, aggregate,
and maintenance. To maximize pick life, the picks must
be free to rotate in the holder.
The pick has two functions:
•
Allow only persons to perform maintenance on this
attachment who have been properly trained in its safe
operation.
• Serve as a consumable cutting tool.
• Protect the holder.
•
Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting implement
back into service.
If the pick is not free to rotate in the holder or if the pick
locks up in the holder, pick and pick holder wear is greatly
accelerated.
•
Backup alarm must be in good working order to warn
others. Use a backup camera or rear-view mirror that is in
good condition to help see undesirable situations behind the
unit. Drive at a slower speed to compensate for blind spots.
•
Do not alter attachment or replace parts on the attachment
with other brands. Other brands may not fit properly or
meet OEM specifications. They can weaken the integrity
and impair the safety, function, performance, and life of the
attachment. Replace parts only with genuine OEM parts.
•
Check hydraulic hoses and fittings frequently for leaks or
damage. Fluid escaping under pressure can penetrate skin.
Large leaks can drop the attachment.
•
Lubricate, make adjustments and repairs in a safe area
away from traffic and other hazards.
•
Check hitch fit-up frequently. An improper fit-up can cause
the attachment to come loose from the loader hitch plate
and fall.
6/13/19
Edge picks wear faster than center picks due to side
loading of the drum during the power unit’s steering
corrections.
To promote pick rotation in the holder, spray picks daily
with a water based asphalt emulsifier to break down
asphalt emulsion. (Example: Zep’s part #AR6690)
If the pick remains in the holder beyond the intended
replacement point, it reduces the cutting performance
and will not protect the holder. If the picks are worn
enough to indicate slight holder wear, replace pick
immediately.
Use Water Spray Kit provided by Kubota to increase pick
life by 20% to 40% and to suppress milling dust. Refer to
“Water Spray Kit (Accessory)” on page 26.
Figure 4-1 and Figure 4-3 on page 28 show examples of
excessively worn picks.
AP-CP30 Series Cold Planer 350-376MK
27
Table of Contents
Section 4: Maintenance & Lubrication
72101
Examples of remaining pick life (%)
100
95
75
90
Rotating Picks
40
20
0
-5
Non-Rotating Picks
Picks may last twice as long if they are free to rotate in their holder
Varying Degrees of Pick Wear
Figure 4-1
72100
72149
Pick is no longer rotating in the holder,
causing premature pick and holder wear.
Fork Pick Tool
Figure 4-2
Remove & Install Picks
Refer to Figure 4-2:
!
WARNING
To avoid serious injury or death:
• Never strike a pick on the carbide tip. The carbide can
break or chip and cause injury.
•
Always wear eye protection when removing and installing
picks. Carbide picks can shatter causing injury.
A fork type pick tool (#1) is included with the Cold Planer
and should be used to remove picks from the holders.
Insert the fork into the groove on the pick and strike the
tool with a hammer. In the event the pick tool is not
available, a punch can be inserted into the bottom of the
pick holders and tapped on the underside of the pick to
dislodge it.
For installation, the fork type tool should be inserted into
the groove on the pick and struck with a hammer. If the
tool is not available, a length of pipe with a 3/4 to 1 inch
inside diameter can be placed over the pick to protect the
28
AP-CP30 Series Cold Planer 350-376MK
Results of a Non-Rotating Pick
Figure 4-3
carbide pick from a direct hit. Striking a small piece of
wood placed on top the pipe to absorb the shock will also
help prevent damage to the pick and pick holder.
Pick Holder Repair
Refer to Figure 4-3:
IMPORTANT: To avoid bearing damage, always
ground directly to the drum before welding.
IMPORTANT: Kubota does not warrant any ground
engaging parts (drum, picks, holders, or bases)
against wear, unless the wear is determined by
Kubota to have been caused by a manufacturing
defect.
If a pick holder becomes worn, note the position and
angle of the holder. Cut the pick holder from the drum
using a torch or air-arc. Weld the new holder to the drum
in the noted position.
6/13/19
Table of Contents
Section 4: Maintenance & Lubrication
72108
Fill Plug Hole
Planetary Gearbox
Motor
Oil Level Plug
Planer Drum
Drain Plug Hole
Shown Exploded For Clarity
!
DANGER
!
WARNING
To avoid serious injury or death:
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment supported
by concrete blocks or hydraulics. Concrete can break,
hydraulic lines can burst, and/or hydraulic controls can be
actuated even when power to hydraulics is off.
To avoid serious injury or death:
• Always shut power machine down following the “Shutdown
Procedure” provided in this manual before leaving the
operator’s seat.
•
Do not alter attachment or replace parts on the attachment
with other brands. Other brands may not fit properly or
meet OEM specifications. They can weaken the integrity
and impair the safety, function, performance, and life of the
attachment. Replace parts only with genuine OEM parts.
Refer to Figure 4-4:
The planetary gearbox oil should be drained and refilled
at 100 hours of operation and every 250 hours or yearly,
whichever comes first, after initial oil change.
1.
Clean off any dirt and grease that may have
accumulated on the Cold Planer and moving parts.
Scrape compacted dirt from the drum and then wash
surface thoroughly with a garden hose.
The planetary gearbox contains synthetic EP90 gear oil
and should be half full during operation.
2. Check picks and pick holders for wear and replace if
necessary. Check picks to make sure they rotate in
the pick holders.
Change Oil In Planetary Gearbox
Figure 4-4
Planetary Gearbox Oil Change
Oil drain and fill procedure:
1.
Clean area around plug holes on gearbox.
2. Remove the two drain plugs on the gearbox. Rotate
drum so that a plug hole is on the bottom to drain the
gearbox of oil.
3. Drain oil into an approved container.
4. Rotate planer drum and gearbox until one plug hole
is horizontal and the other plug hole is on top.
5. Slowly fill gearbox though the top fill hole until oil
reaches the horizontal oil level hole.
6. The gearbox should be half full of AGMA EP90
synthetic gear lubricant or SAE 75W90 synthetic
gear lubricant. (Chevron RPM Synthetic 75W90 for
example). The approximate volume of the gearbox is
30 oz.
7.
Replace the two gearbox plugs and tighten.
Long-Term Storage
Clean, inspect, service, and make necessary repairs to
the Cold Planer when parking it for long periods and
when parking it at the end of a working season. This will
help ensure that the planer is ready for field use the next
time you hook-up to it.
3. Spray picks with a water based asphalt emulsifier to
break down asphalt emulsion and to promote pick
rotation. (Example: Zep’s part #AR6690).
4. Inspect planer for parts out of adjustment, loose,
damaged, or worn. Make required adjustments.
Tighten all loose hardware. Replace damaged and
worn parts as needed.
5. Repaint parts where paint is worn or scratched to
prevent rust. Ask your Kubota dealer for touch-up
paint. Paint is available in aerosol can, quarts, and
gallon sizes. See chart below.
Touch-Up Paint
Part No.
Part Description
821-070C
821-070CTU
821-070CQT
821-070CGL
Gloss black enamel spray can
Gloss black enamel bottle with brush
Gloss black enamel quart
Gloss black enamel gallon
6. Replace all damaged or missing decals.
7.
Lubricate as noted under “Lubrication Points” on
page 30.
8. A light coat of oil or grease may be applied to
exposed cylinder rods to minimize oxidation.
9. Store Cold Planer on a level surface in a clean, dry
place. Inside storage will reduce maintenance and
make for a longer planer life.
6/13/19
AP-CP30 Series Cold Planer 350-376MK
29
Table of Contents
Section 4: Maintenance & Lubrication
Lubrication
Legend
Multi-purpose
spray lube
Multi-purpose
grease lube
Multi-purpose
oil lube
50
Hrs
Intervals in hours at which
lubrication is required
Lubrication Points
Low-Flow Cold Planers
72131
Weekly
Sideshift Bars
2 - Sideshift Bars (Upper and Lower)
Type of Lubrication:
Graphite lube spray such as CRC 30094
Quantity: Clean and spray sideshift bars once a week.
IMPORTANT: Do not apply grease to the sideshift
bars. Grease catches milling dust and causes
the sideshift mechanism to bind and wear
quickly.
72131
8
Hours
Dead Shaft Bearing
1 - Zerk
Type of Lubrication:
EP Lithium NLGL No. 2 grade Grease
Quantity: Add grease until grease begins to emerge.
30
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Section 4: Maintenance & Lubrication
72130
8
Hours
Depth Jack
3- Zerks
Type of Lubrication:
EP Lithium NLGL No. 2 grade Grease
Quantity: Add grease until grease begins to emerge.
72129
8
Hours
Tilt Jack
3- Zerks
Type of Lubrication:
EP Lithium NLGL No. 2 grade Grease
Quantity: Add grease until grease begins to emerge.
6/13/19
AP-CP30 Series Cold Planer 350-376MK
31
Table of Contents
Section 4: Maintenance & Lubrication
High-Flow Cold Planers
72127
Weekly
Sideshift Bars
2 - Sideshift Bars (Upper and Lower)
Type of Lubrication:
Graphite lube spray such as CRC 30094
Quantity: Clean and spray sideshift bars once a week.
IMPORTANT: Do not apply grease to the sideshift
bars. Grease catches milling dust and causes
the sideshift mechanism to bind and wear
quickly.
Typical Both Sides
72127
Weekly
Left and Right Depth Skids
4 - Retained Skid Locations
Type of Lubrication:
Graphite lube spray such as CRC 30094
Quantity: Spray deft skid bars once a week.
IMPORTANT: Do not apply grease to the depth
skids. Grease catches milling dust and causes
the deft skid mechanism to bind and wear
quickly.
Typical Both Sides
32
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Section 4: Maintenance & Lubrication
72127
8
Hours
Dead Shaft Bearing
1 - Zerk
Type of Lubrication:
EP Lithium NLGL No. 2 Grade Grease
Quantity: Add grease until grease begins to emerge.
This Side Only
72127
40 hrs
or
Weekly
Depth Cylinder Pivot Pins
4 - Zerk
Lubricate every 40 hours of use or weekly, whichever
comes first.
Type of Lubrication:
EP Lithium NLGL No. 2 Grade Grease
Quantity: Add grease until grease begins to emerge.
Typical Both Sides
72108
Fill Plug
250 hrs
or
yearly
Planetary Gearbox
Motor
Planetary Gearbox
Type of Lubrication: Synthetic EP90 Gear Oil
Oil Level Plug
Change oil at the first 100 hours of use. Thereafter,
change every 250 hours or yearly, whichever comes first.
Quantity: Fill until oil reaches oil level plug hole which is
rotated to be horizontal, approximately 30 oz.
Refer to “Planetary Gearbox Oil Change” on page 29.
Planer Drum
Drain Plug
Shown Exploded For Clarity
6/13/19
AP-CP30 Series Cold Planer 350-376MK
33
Table of Contents
Section 5: Specifications & Capacities
Section 5: Specifications & Capacities
CP30 Series Cold Planers
Specifications & Capacities
Model Numbers
CP3012LF CP3016LF CP3018
Cutting width
inches (cm)
Cutting depth
inches (cm)
12 (31)
16 (41)
30
38
Min. hydraulic flow gpm (Lpm)
15 (56.8)
Max. hydraulic flow gpm (Lpm)
25 (94.6)
psi
(MPa)
Maximum pressure
psi (MPa)
Tilt capability
inches (cm)
Wall clearance
inches (cm)
CP3048
40 (102)
48 (122)
76
90
0 to 6 (0 to 15)
40
50
24 (91)
27 (102)
2,000
(13,8)
±15
60
30 (114)
2,000
(13,8)
2,500
(17.2)
3,500
(24.1)
±8
±6
5,000 (34.4)
±15
±13
±10
Not available
4 (10 cm)
Not applicable
EP90 or SAE75W90 Synthetic Gear lubricant
Not applicable
1350
(612)
1450
(658)
Approximately 30 oz (1 L)
1805
(819)
1970
(894)
2155
(978)
49 1/2"
(1.26 m)
2450
(1111)
2685
(1218)
49"
(1.24 m)
67 1/2"
(1.71 m)
67"
(1.7 m)
37 1/2"
(.95 m)
31"
(79 cm)
CP3012LF & CP3016LF
34
3,000
(20.7)
26 (66)
Planetary gearbox oil capacity
lbs
(kg)
CP3040
30 (76)
3,500 (24.1)
Planetary gearbox oil type
Approximate weight
CP3030
24 (61)
42 (159)
2,000
(13.8)
degrees
Sideshift travel
CP3024
0 to 5 (0 to 13)
Number of picks
Minimum pressure
18 (46)
AP-CP30 Series Cold Planer 350-376MK
CP301818, CP3024, CP3030, CP3040, & CP3048
6/13/19
Table of Contents
Section 6: Features & Benefits
Section 6: Features & Benefits
CP3012LF & CP3016LF Low-Flow Cold Planers
Features
Benefits
Removable carbide picks
Uses rocket fin technology that is built into the picks for longer life. Easy to replace.
Hydraulic sideshift
Drum engagement and sideshift are integrated into the multi-function grips of
the SSV/SVL.
Manual tilt and depth adjustment
Economical and easy to adjust.
CP3018, CP3024, CP3030, CP3040, & CP3048 High-Flow Cold Planers
Features
Benefits
Removable carbide picks
Uses rocket fin technology that is built into the picks for longer life. Easy to replace.
Skid shoes adjust independently
with hydraulic cylinders
Allows the planer to follow curb and gutter as well as the contour of the road or street.
Tilt, depth, and sideshift adjust
hydraulically
All functions are integrated into the multi-function grips of the SSV/SVL.
Case drain
Protects hydraulic motor and seals.
6/13/19
AP-CP30 Series Cold Planer 350-376MK
35
Table of Contents
Section 7: Troubleshooting
Section 7: Troubleshooting
Troubleshooting Chart
Problem
Drum does not rotate.
Drum rotates backward.
Motor oil seal is leaking.
Pick is wearing unevenly.
Cause
Auxiliary hydraulics switch for continuous
operation is not engaged.
Pick holders are wearing.
Engage auxiliary hydraulics switch for
continuous operation.
One or both of the hydraulic couplers are not Reconnect couplers to skid steer auxiliary
fully connected.
hydraulic outlets.
Male and female hydraulic couplers are
connected in reverse order.
Switch male and female couplers on
hydraulic hoses and then reconnect hoses to
the auxiliary hydraulic outlets.
Return line from motor has been pinched or
is collapsed.
Replace motor seal. Check motor return
hose for kinks.
Case drain line is not properly connected.
Connect case drain line to the hydraulic
motor and skid steer reservoir.
Pick is not rotating in the holder.
Spray picks daily with a water based asphalt
emulsifier to break down asphalt emulsion.
Example: Zep’s part # AR6690
Not inspecting picks frequently.
Inspect picks every 30 minutes of operation
for sign of pick rotation and wear. Replace
picks as needed. Refer to “Remove &
Install Picks” on page 28.
Picks are not kept clean.
Recommend adding a Water Spray Kit. This
kit can increase tooth life by 20 to 40% and
suppress milling dust.
Picks are cutting concrete most of the time.
Replace standard asphalt picks with concrete
picks.
Side loading on the drum during steering
corrections.
Make straight cuts. Keep steering corrections
to a minimum.
Not inspecting pick holders frequently.
Inspect pick holders every 30 minutes of
operation for wear. Replace pick holders as
needed. Refer to “Pick Holder Repair” on
page 28.
Pick is not rotating in the holder.
Spray picks daily with a water based asphalt
emulsifier to break down asphalt emulsion.
Example: Zep’s part # AR6690
Picks do not last long.
Edge picks are wearing faster
than the center picks.
Solution
Replace pick if pick is worn enough to
Pick is worn beyond its intended replacement indicate slight holder wear.
point.
Replace pick holder if worn excessively.
36
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Section 8: Torque Values Chart
Section 8: Torque Values Chart
Torque Values Chart for Common Bolt Sizes
Bolt Head Identification
Bolt Size
(inches)
1
in-tpi
1/4" - 20
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
Grade 2
N·m
7.4
8.5
15
17
27
31
43
49
66
75
95
105
2
ft-lb
5.6
6
11
13
20
22
32
36
49
55
70
79
Grade 5
3
N · m ft-lb
11
8
13
10
24
17
26
19
42
31
47
35
67
49
75
55
105
76
115
85
150
110
165
120
Grade 8
N · m ft-lb
16
12
18
14
33
25
37
27
59
44
67
49
95
70
105
78
145
105
165
120
210
155
235
170
Bolt Head Identification
Bolt Size
(Metric)
mm x pitch
M 5 X 0.8
M6X1
M 8 X 1.25
M8X1
M10 X 1.5
M10 X 0.75
M12 X 1.75
M12 X 1.5
M12 X 1
M14 X 2
M14 X 1.5
M16 X 2
4
5.8
8.8
10.9
Class 5.8
Class 8.8
Class 10.9
N·m
4
7
17
18
33
39
58
60
90
92
99
145
ft-lb
3
5
12
13
24
29
42
44
66
68
73
105
N·m
6
11
26
28
52
61
91
95
105
145
155
225
ft-lb
5
8
19
21
39
45
67
70
77
105
115
165
N·m
9
15
36
39
72
85
125
130
145
200
215
315
ft-lb
7
11
27
29
53
62
93
97
105
150
160
230
M16 X 1.5
155
115
240
180
335
245
5/8" - 11
130
97
205
150
285
210
5/8" - 18
150
110
230
170
325
240
M18 X 2.5
195
145
310
230
405
300
3/4" - 10
235
170
360
265
510
375
M18 X 1.5
220
165
350
260
485
355
3/4" - 16
260
190
405
295
570
420
M20 X 2.5
280
205
440
325
610
450
7/8" - 9
225
165
585
430
820
605
M20 X 1.5
310
230
650
480
900
665
7/8" - 14
250
185
640
475
905
670
M24 X 3
480
355
760
560
1050 780
1" - 8
340
250
875
645
1230 910
M24 X 2
525
390
830
610
1150
845
1" - 12
370
275
955
705
1350 995
M30 X 3.5
960
705
1510 1120
2100 1550
1-1/8" - 7
480
355
1080 795
1750 1290
M30 X 2
1060 785
1680 1240 2320 1710
1-1/8" - 12
540
395
1210 890
1960 1440
M36 X 3.5
1730 1270 2650 1950 3660 2700
1-1/4" - 7
680
500
1520 1120 2460 1820
M36 X 2
1880 1380 2960 2190 4100 3220
1 in-tpi = nominal thread diameter in inches-threads per inch
1-1/4" - 12
750
555
1680 1240 2730 2010
2 N· m = newton-meters
1-3/8" - 6
890
655
1990 1470 3230 2380
3 ft-lb= foot pounds
1-3/8" - 12
1010
745
2270 1670 3680 2710
4 mm x pitch = nominal thread diameter in millimeters x thread
1-1/2" - 6
1180
870
2640 1950 4290 3160
pitch
1-1/2" - 12
1330 980
2970 2190 4820 3560
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
6/13/19
AP-CP30 Series Cold Planer 350-376MK
37
Table of Contents
Section 9: Warranty & Legal Disclaimer
Section 9: Warranty & Legal Disclaimer
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit: One year Parts and Labor
Hydraulic Motor: Two years Parts and Labor
Hydraulic Cylinder: One year Parts and Labor;
Hoses and seals are considered wear items.
Drums, Picks, Pick Holders, and Bases: Considered wear items
This Warranty is limited to the repair or replacement of any defective part by
Land Pride and the installation by the dealer of any such replacement part, and
does not cover common wear items such as blades, belts, tines, etc. Land Pride
reserves the right to inspect any equipment or parts which are claimed to have
been defective in material or workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points and driveline shafts.
Claims under this Warranty should be made to the dealer which originally sold
the product and all warranty adjustments must be made through an authorized
Kubota dealer. Kubota reserves the right to make changes in materials or design
of the product at any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in this
written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days from
the date of original purchase.
IMPORTANT: The Online Warranty Registration should be completed by the dealer at the time of
purchase. This information is necessary to provide you with quality customer service.
Model Number ____________________ Serial Number ____________________
38
AP-CP30 Series Cold Planer 350-376MK
6/13/19
Table of Contents
Section 9: Warranty & Legal Disclaimer
Legal Disclaimer
Kubota Corporation notes that specifications and technical information are subject to change without notice and Kubota
does not represent or warrant that the information in this publication is completely accurate or current; however, Kubota
used reasonable efforts to set forth and include accurate and up to date information in this publication. Kubota disclaims
all representations and warranties, whether express or implied, including, but not limited to, warranties of merchantability
and fitness for a particular purpose and Kubota shall not be liable for any damages, whether compensatory, direct,
indirect, incidental, special, or consequential, arising out of or in connection with the use of this publication, or in the
information therein.
The Product(s) described in this Publication are designed and manufactured only for the country in which they are
initially wholesaled by Kubota. Kubota does not provide parts, warranty or service for any Product which is re-sold or
retailed in any country other than the country for which the Product(s) were designed or manufactured.
6/13/19
AP-CP30 Series Cold Planer 350-376MK
39
KUBOTA TRACTOR CORPORATION
1000 Kubota Drive, Grapevine, TX 76051
Telephone: (817) 756-1171
Western Division:
Telephone:
Central Division:
Telephone:
Northern Division:
Telephone:
Southeast Division:
Telephone:
1175 S. Guild Ave., Lodi, CA 95240
(209) 334-9910
14855 FAA Blvd., Fort Worth, TX 76155
(817) 571-0900
6300 at One Kubota Way, Groveport, OH 43125
(614) 835-1100
1025 Northbrook Parkway, Suwanee, GA 30024
(770) 995-8855
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement