Land Pride SW30 Series Operator Manual

Land Pride SW30 Series Operator Manual
Table of Contents
Road Saw
AP-SW3010 & AP-SW3018
Models: AP-SW3010-2.5 & AP-SW3010-4.5
Models: AP-SW3018-3.0, AP-SW3018-4.5, & AP-SW3018-6.0
72139
72183
SW3010 Road Saws
SW3010-2.5, & SW3010-4.5
SW3018 Road Saws
SW3018-3.0, SW3018-4.5, & SW3018-6.0
350-386MK
Operator’s Manual
!
Read the Operator’s Manual entirely. When you see this symbol,
the subsequent instructions and warnings are serious - follow
without exception. Your life and the lives of others depend on it!
Cover photo may show optional equipment not supplied
with standard unit.
For an Operator’s Manual and Decal Kit in French
Language, please see your Kubota dealer.
Printed 5/17/19
Machine Identification
Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new
manual.
If you, or the dealer, have added Options not originally ordered with the machine, or removed Options that were
originally ordered, the weights and measurements are no longer accurate for your machine. Update the record by
adding the machine weight and measurements provided in the Specifications & Capacities Section of this manual with
the Option(s) weight and measurements.
Model Number
Serial Number
Machine Height
Machine Length
Machine Width
Machine Weight
Delivery Date
First Operation
Accessories
Dealer Contact Information
Name:
Street:
City/State:
Telephone:
Email:
!
California Proposition 65
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Table of Contents
Important Safety Information . . . . . . . . . . . . . 1
Section 4: Maintenance & Lubrication . . . . . 28
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol . . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Servicing Drivetrain Components . . . . . . . . . . . . . 28
Cutting Wheel Maintenance . . . . . . . . . . . . . . . . . 28
Remove & Install Picks . . . . . . . . . . . . . . . . . . . . . 29
Pick Holder Repair . . . . . . . . . . . . . . . . . . . . . . . . 29
SW3010 Gearbox Oil Change . . . . . . . . . . . . . . . . 30
SW3018 Gearbox Oil Change . . . . . . . . . . . . . . . . 30
SW3018 Wheel Mounting Bolts . . . . . . . . . . . . . . . 31
SW3010 Wheel Mounting Nuts . . . . . . . . . . . . . . . 31
Long-Term Storage . . . . . . . . . . . . . . . . . . . . . . . . 32
Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . . 33
SW3010 Road Saws . . . . . . . . . . . . . . . . . . . . . 33
Sideshift Bars . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Sideshift Rod . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Planetary Gearbox . . . . . . . . . . . . . . . . . . . . . . .33
SW3018 Road Saws . . . . . . . . . . . . . . . . . . . . . 34
Depth Cylinder Pivot Pins . . . . . . . . . . . . . . . . .34
Depth Arm Pivot Pins . . . . . . . . . . . . . . . . . . . . .34
Sideshift Rods . . . . . . . . . . . . . . . . . . . . . . . . . .35
Planetary Gearbox . . . . . . . . . . . . . . . . . . . . . . .35
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . 12
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 12
Section 1: Assembly & Set-up . . . . . . . . . . . 13
Skid Steer Requirements . . . . . . . . . . . . . . . . . . .
Torque Requirements . . . . . . . . . . . . . . . . . . . . . .
Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . .
Skid Steer Shutdown Procedure . . . . . . . . . . . . . .
Dealer Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lift Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Couplers . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Hoses and Fittings . . . . . . . . . . . . . . .
Wire Harness . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutting Wheel Assembly . . . . . . . . . . . . . . . . . .
Motor Case Drain . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
13
14
14
14
14
14
14
15
15
Section 2: Operating Procedures . . . . . . . . . 16
General Safety Information . . . . . . . . . . . . . . . . . .
Hook-up Road Saw . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Hose Hook-up . . . . . . . . . . . . . . . . . . . .
Electrical Hook-up . . . . . . . . . . . . . . . . . . . . . . . . .
Pre-Operation Inspection . . . . . . . . . . . . . . . . . . .
Check Equipment Clearances . . . . . . . . . . . . . . . .
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating the SW3010 . . . . . . . . . . . . . . . . . . .
Operating the SW3018 . . . . . . . . . . . . . . . . . . .
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unhook Road Saw . . . . . . . . . . . . . . . . . . . . . . . .
16
18
19
20
22
22
23
23
24
24
25
Section 5: Specifications & Capacities . . . . . 36
Section 6: Features & Benefits . . . . . . . . . . . 37
Section 7: Troubleshooting . . . . . . . . . . . . . . 38
Section 8: Torque Values Chart . . . . . . . . . . . 39
Section 9: Warranty & Legal Disclaimer . . . . 40
Section 3: Options & Accessories . . . . . . . . 26
Picks (Accessory) . . . . . . . . . . . . . . . . . . . . . . . . . 26
Water Spray Kit (Accessory) . . . . . . . . . . . . . . . . . 26
Operator Protective Door (Optional) . . . . . . . . . . . 26
© Copyright 2019 All rights Reserved
Kubota provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Kubota
assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Kubota reserves the right
to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
Kubota is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
Table of Contents
Table of Contents Continued
See previous page for Table of Contents.
Parts Manual QR Locator
Dealer QR Locator
The QR (Quick Reference) code on the
cover and to the left will take you to the
Parts Manual for this equipment.
Download the appropriate App on your
smart phone, open the App, point your
phone on the QR code and take a picture.
The QR code on the left will
link you to available dealers
for Kubota products. Refer to
Parts Manual QR Locator on
this page for detailed
instructions.
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19

Important Safety Information
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Safety at All Times
Careful operation is your best
assurance against an accident.
All operators, no matter how much
experience they may have, should
carefully read this manual and
other related manuals, or have the
manuals read to them, before
operating the power machine and
this attachment.
 Thoroughly read and understand
the “Safety Label” section. Read
all instructions noted on them.
 Do not operate the equipment
while under the influence of drugs
or alcohol as they impair the ability
to safely and properly operate the
equipment.
 Operator should be familiar with all
functions of the skid steer and
attachment and be able to handle
emergencies quickly.
 Make sure all guards and shields
appropriate for the operation are in
place and secured before
operating the attachment.
 Keep all bystanders away from
equipment and work area.
 Start skid steer from the driver’s
seat with steering levers and
hydraulic controls in neutral.
 Operate skid steer and controls
from the driver’s seat only.
 Never dismount from a moving
skid steer or leave skid steer
unattended with engine running.
 Do not allow anyone to stand
between attachment and skid
steer while hooking-up.
 Keep hands, feet, and clothing
away from power-driven parts.
 While transporting and operating
equipment, watch out for objects
overhead and along side such as
fences, trees, buildings, wires, etc.
 Store attachment in an area where
children normally do not play.
When needed, secure attachment
against falling with support blocks.
5/17/19
!
Look for the Safety Alert Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention are
dependent upon the awareness, concern, prudence, and
proper training of personnel involved in the operation,
transport, maintenance, and storage of equipment.
Be Aware of
Signal Words
A signal word designates a degree or
level of hazard seriousness. The
signal words are:
! DANGER
Indicates a hazardous situation that, if
not avoided, will result in death or
serious injury.
! WARNING
Indicates a hazardous situation that, if
not avoided, could result in death or
serious injury.
! CAUTION
Indicates a hazardous situation that, if
not avoided, may result in minor or
moderate injury.
Safety Precautions for
Children
Skid Steer Shutdown
And Storage
Tragedy can occur if the operator
is not alert to the presence of
children. Children generally are
attracted to attachments and their
work.
 Never assume children will remain
where you last saw them.
 Keep children out of the work area
and under the watchful eye of a
responsible adult.
 Be alert and shut the attachment
and skid steer/track loader down if
children enter the work area.
 Never carry children on the power
machine or attachment. There is
not a safe place for them to ride.
They may fall off and be run over
or interfere with the control of the
power machine.
 Never allow children to operate the
power machine, even under adult
supervision.
 Never allow children to play on the
power machine or attachment.
 Use extra caution when backing
up. Before the power machine
starts to move, look down and
behind to make sure the area is
clear.
 Reduce engine speed and shut-off
all power to the attachment.
 Park on solid, level ground and
lower attachment until it is flat on
the ground or support blocks.
 Turn off engine, and remove
switch key to prevent unauthorized
starting.
 Relieve all hydraulic pressures.
 If included, raise seat bar and
move controls until both lock.
 Wait for all components to stop
before leaving operator’s seat.
 Use steps, grab-handles and
anti-slip surfaces when stepping
on and off the skid steer.
 Detach and store attachment in an
area where children normally do
not play. Secure attachment by
using blocks and supports.
OFF
RE M O
VE
1
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Dig Safe - Avoid
Underground Utilities
 USA: Call 811
CAN: digsafecanada.ca
Always contact your local utility
companies (electrical, telephone,
gas, water, sewer, and others)
before digging so that they may
mark the location of any
underground services in the
area.
 Be sure to ask how close you can
work to the marks they
positioned.
2
Transport Safely
 Comply with federal, state, and local
laws.
 Use towing vehicle and trailer of
adequate size and capacity. Secure
equipment towed on a trailer with
chocks, tie downs, and chains.
 Sudden braking can cause a towed
trailer to swerve and upset. Reduce
speed if towed trailer is not equipped
with brakes.
 Avoid contact with any overhead
utility lines or electrically charged
conductors.
 Always drive with load on end of
loader arms low to the ground.
 Always drive straight up and down
steep inclines with heavy end of skid
steer on the “uphill” side.
Tire Safety
Practice Safe Maintenance
 Tire changing can be dangerous
and must be performed by
trained personnel using the
correct tools and equipment.
 Always maintain correct tire
pressure. Do not inflate tires
above recommended pressures
shown in the Operator’s Manual.
 When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
 Securely support the attachment
when changing a wheel.
 When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
 Make sure wheel bolts have been
tightened to the specified torque.
 Understand procedure before doing
work. Refer to the Operator’s Manual
for additional information.
 Work on a level surface in a clean
dry area that is well-lit.
 Lower attachment to the ground and
follow all shutdown procedures
before leaving the operator’s seat to
perform maintenance.
 Do not work under any hydraulic
supported equipment. It can settle,
suddenly leak down, or be lowered
accidentally. If it is necessary to work
under the equipment, securely
support it with stands or suitable
blocking beforehand.
 Use properly grounded electrical
outlets and tools.
 Use correct tools and equipment for
the job that are in good condition.
 Allow equipment to cool before
working on it.
 Engage park brake when stopped on
an incline.
 Maximum transport speed for an
attached equipment is 20 mph. DO
NOT EXCEED. Never travel at a
speed which does not allow
adequate control of steering and
stopping. Some rough terrains
require a slower speed.
 As a guideline, use the following
maximum speed weight ratios for
attached equipment:
20 mph when weight of attached
equipment is less than or equal to
the weight of machine towing the
equipment.
10 mph when weight of attached
equipment exceeds weight of
machine towing equipment but not
more than double the weight.
 IMPORTANT: Do not tow a load that
is more than double the weight of the
vehicle towing the load.
 Disconnect battery ground cable (-)
before servicing or adjusting
electrical systems or before welding
on equipment.
 Inspect all parts. Make certain parts
are in good condition & installed
properly.
 Replace parts on this attachment
with genuine Kubota parts only. Do
not alter this attachment in a way
which will adversely affect its
performance.
 Do not grease or oil attachment
while it is in operation.
 Remove buildup of grease, oil, or
debris.
 Always make sure any material and
waste products from the repair and
maintenance of the attachment are
properly collected and disposed.
 Remove all tools and unused parts
from the equipment before
operation.
5/17/19
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Prepare for Emergencies
 Be prepared if a fire starts.
 Keep a first aid kit and fire
extinguisher handy.
 Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
Wear Personal Protective
Equipment (PPE)
Avoid High
Pressure Fluids Hazard
 Wear protective clothing and
equipment appropriate for the job
such as safety shoes, safety
glasses, hard hat, and ear plugs.
 Clothing should fit snug without
fringes and pull strings to avoid
entanglement with moving parts.
 Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
 Operating equipment safely
requires the operator’s full
attention. Avoid wearing
headphones while operating
equipment.
 Escaping fluid under pressure
can penetrate the skin causing
serious injury.
 Relieve all residual pressure
before disconnecting hydraulic
lines or performing work on the
hydraulic system.
 Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
 Use a piece of paper or
cardboard, NOT BODY PARTS,
to check for suspected leaks.
 Wear protective gloves and
safety glasses or goggles when
working with hydraulic systems.
 DO NOT DELAY. If an accident
occurs, see a doctor familiar with
this type of injury immediately.
Any fluid injected into the skin or
eyes must be treated
within a few hours or
gangrene may
result.
Use Seat Belt and ROPS
Keep Riders Off
Machinery
911
Use Safety
Lights and Devices
 Slow moving tractors, skid steers,
and self-propelled machines can
create a hazard when driven on
public roads. They are difficult to
see, especially at night. Use the
Slow Moving Vehicle (SMV) sign
when on public roads.
 Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
5/17/19
 Kubota recommends the use of a
CAB or roll-over-protectivestructures (ROPS) and seat belt
in almost all power machines.
Combination of a CAB or ROPS
and seat belt will reduce the risk
of serious injury or death if the
power machine should be upset.
 If ROPS is in the locked-up
position, fasten seat belt snugly
and securely to help protect
against serious injury or death
from falling and machine
overturn.
 Never carry riders on skid steer
or attachment.
 Riders obstruct operator’s view
and interfere with the control of
the power machine.
 Riders can be struck by objects
or thrown from the equipment.
 Never use skid steer or
attachment to lift or transport
riders.
3
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Avoid crystalline Silica
(quartz) Dust
Because crystalline silica is a basic
component of sand and granite,
many activities at construction sites
produce dust containing crystalline
silica. Trenching, sawing, and boring
of material containing crystalline
silica can produce dust containing
crystalline silica particles. This dust
can cause serious injury to the
lungs (silicosis).
There are guidelines which should
be followed if crystalline silica
(quartz) is present in the dust.
 Be aware of and follow OSHA
(or other local, State, or Federal)
guidelines for exposure to airborne
crystalline silica.
 Know the work operations where
exposure to crystalline silica may
occur.
 Participate in air monitoring or
training programs offered by the
employer.
 Be aware of and use optional
equipment controls such as water
sprays, local exhaust ventilation,
and enclosed cabs with positive
pressure air conditioning if the
machine has such equipment.
Otherwise respirators shall be worn.
 Where respirators are required, wear
a respirator approved for protection
against crystalline silica containing
dust. Do not alter respirator in any
way. Workers who use tight-fitting
respirators can not have beards/
mustaches which interfere with the
respirator seal to the face.
 If possible, change into disposable
or washable work clothes at the
work site; shower and change into
clean clothing before leaving the
work site.
 Do not eat, drink, use tobacco
products, or apply cosmetics in
areas where there is dust containing
crystalline silica.
 Store food, drink, and personal
belongings away from the work
area.
 Wash hands and face before eating,
drinking, smoking, or applying
cosmetics after leaving the exposure
area.
Handle
Chemicals Properly
 Protective clothing should be
worn.
 Handle all chemicals with care.
 Follow instructions on container
label.
 Agricultural chemicals can be
dangerous. Improper use can
seriously injure persons, animals,
plants, soil, and property.
 Inhaling smoke from any type of
chemical fire can be a serious
health hazard.
 Store or dispose of unused
chemicals as specified by the
chemical manufacturer.
4
5/17/19
Important Safety Information
This page left blank intentionally.
5/17/19
5
Table of Contents
Important Safety Information
Important Safety Information
Safety Labels
3.
Your Road Saw comes equipped with all safety labels in place.
They are designed to help you safely operate your attachment.
Read and follow their directions.
1. Keep all safety labels clean and legible.
2. Refer to this section for proper label placement. Replace
all damaged or missing labels. Order new labels from your
nearest Kubota dealer. To find your nearest dealer, visit
our dealer locator at www.landpride.com.
4.
Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
specified by Kubota. When ordering new components make
sure the correct safety labels are included in the request.
Refer to this section for proper label placement.
To install new labels:
a. Clean surface area where label is to be placed.
b. Spray soapy water onto the cleaned area.
c. Peel backing from label and press label firmly onto the
surface.
d. Squeeze out air bubbles with edge of a credit card or
with a similar type of straight edge.
844-124C
838-094C
Warning: Silica Dust Hazard (1 place)
Warning: High Pressure Fluid Hazard (1 place)
72184
72173
72183
72173
SW3010 Models
72173
72139
SW3018 Models
6
SW3010 Models
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
SW3018 Models
5/17/19
Table of Contents
Important Safety Information
818-798C
818-798C
Warning: Pinch Point Hazard (2 places)
Warning: Pinch Point Hazard (2 places)
SW3010 Models
SW3018 Models
72183
72139
72184
72173
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
7
Table of Contents
Important Safety Information
858-772C
858-772C
Danger: Rotating Parts Hazard (2 places)
Danger: Rotating Parts Hazard (2 places)
SW3010 Models
SW3018 Models
8
72183
72139
72184
72173
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Important Safety Information
844-046C
844-046C
Warning: Thrown Object Hazard (3 places)
Warning: Thrown Object Hazard (3 places)
SW3010 Models
SW3018 Models
72183
72139
72184
72173
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
9
Table of Contents
Important Safety Information
72184
SW3010 Models
72173
848-392C
Warning: Flying Objects and Dust Hazard (1 place)
SW3018 Models
10
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Important Safety Information
72184
SW3010 Models
72173
838-293C
Warning: Read Operator’s manual (1 place)
SW3018 Models
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
11
Table of Contents
Introduction
Introduction
Kubota welcomes you to the growing family of new
product owners. This Road Saw has been designed with
care and built by skilled workers using quality materials.
Proper assembly, maintenance, and safe operating
practices will help you get years of satisfactory use from
this product.
Application
Kubota’s SW3010 and SW3018 Road Saws are
hydraulically powered attachments intended for cutting
asphalt or concrete surfaces with uses and applications
around streets, parking lots, driveways, construction sites,
municipalities, parks, and universities.
These Road Saws utilize a ground-engaging frame and a
cutting wheel that moves up and down inside this frame.
This unique design gives the operator the ability to
maintain control throughout the cut. The cutting wheel is
powered by a hydraulic motor capable of handling up to
42 gpm (159 Lpm). The motor is coupled to a planetary
gearbox to provide maximum cutting torque under load.
Cutting depth is regulated by the cutting wheel radius.
The SW3010 is designed to cut up to 10" (25 cm) deep
while the SW3018 can cut up to 18" (46 cm) deep.
NOTE: A special point of information that the
operator should be aware of before continuing.
Owner Assistance
The Online Warranty Registration should be completed
by the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
The parts on your Road Saw have been specially
designed by Kubota/Land Pride and should only be
replaced with genuine Kubota parts. Contact a Kubota
dealer if customer service or repair parts are required.
Your Kubota dealer has trained personnel, repair parts,
and equipment needed to service this implement.
Serial Number
For quick reference and prompt service, record model
and serial number on the inside cover page and again on
the warranty page. Always provide model number and
serial number when ordering parts and in all
correspondences with your Kubota dealer. For location of
your serial number plate, see Figure 1.
72184
Cutting width is regulated by the cutting wheel width and
arrangement of picks on the cutting wheel. The SW3010
can be purchased in 2.5" or 4.5" (6 cm or 11 cm) widths
while the SW3018 is available in 3", 4.5", and 6"
(8 cm, 11 cm, and 15 cm) widths.
See “Specifications & Capacities” on page 36 and
“Features & Benefits” on page 37 for additional
information and performance enhancing options.
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual, contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge, from our website at
www.landpride.com
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
IMPORTANT: A special point of information related
to the following topic. Kubota’s intention is this
information must be read & noted before continuing.
Serial Number Plate Location
Figure 1
Further Assistance
Your dealer wants you to be satisfied with your new
attachment. If for any reason you do not understand any
part of this manual or are not satisfied with the service
received, the following actions are suggested:
1.
Discuss any problems you have with your attachment
with your dealership service personnel so they can
address the problem.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
question/problem, and request assistance.
3. For further assistance write to:
Kubota by Land Pride
Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
[email protected]
12
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
Skid Steer Requirements
The Road Saw is designed to attach to Kubota skid steers
and track loaders within the following requirements:
Hitch type. . . . . . . Skid steer quick attach, ISO 24410
Horsepower requirements . . . . . . . . . . . . Max 100 hp
Hydraulic flow rates . . . . . . 30-42 gpm (90-159 Lpm)
Min. hydraulic pressure . . . . . . . 2500 psi (13.8 MPa)
Max. hydraulic pressure . . . . . . . 5000 psi (34.5 MPa)
Case drain . . . . . . . . . . . . . . . . . . . . . . . . . . Required
Polycarbonate door . . . . . . . . . . . . . . Recommended
Skid steer weight . . . . . . . . . . . . .See Warning Below
Go through the “Pre-Assembly Checklist” below before
assembling the Road Saw. Speed up your assembly task
and make the job safer by having all needed parts and
equipment readily at hand.
Pre-Assembly Checklist

•
•
•
Consult your power machine’s manual for operating
capacity, lifting capacity, and operating specifications.
Exceeding rated capacities and specifications can result in
a roll-over or other serious hazard.
Do not operate the Road Saw with an open cab machine or
with a tempered front glass window/door on the machine.
We strongly recommend use of a polycarbonate front glass
door/window when operating the Road Saw.
Torque Requirements
Refer to “Torque Values Chart” on page 39 to determine
correct torque values when tightening hardware.
Before You Start
! WARNING
To avoid serious injury or death:
•
Allow only persons to operate this attachment who have
fully read and comprehended this manual, who are properly
trained to operate the attachment safely, and who are age 16
or older. Serious injury or death can result from the failure
to read, understand, and follow instructions provided in this
manual.
Make sure all major components and loose
parts are shipped with the attachment.
Operator’s
Manual
Double check to make sure all parts, fasteners
and pins are installed in the correct location to
lessen the chance of using a bolt incorrectly,
Refer to the Parts Manual if unsure.
Operator’s
Manual
350-386MK
NOTE: All assembled hardware from the
factory has been installed in the correct
location. Remember location of a part or
fastener if removed. Keep parts separated.
Make sure working parts move freely, bolts are
tight & cotter pins are spread.
Power machines outside the listed horsepower range must
not be used. Higher horsepower machines can damage the
attachment. Under horsepower machines make the job more
difficult.
Lightweight power machines may need weight added to the
rear to maintain steering control and prevent forward
tipping or side tipping caused by a heavy front load. Consult
your power machine Operator’s Manual to determine
proper weight requirements and maximum weight
limitations.
Reference
Have a minimum of two people available during assembly.
! WARNING
To avoid serious injury or death:
•
Check
Have a fork lift or loader with properly sized chains and safety
stands capable of lifting and supporting the equipment on hand.
Parts Manual
350-386PK
Operator’s
Manual
Make sure all grease fittings are in place and
lubricated.
Page 33
Make sure all safety labels are correctly
located and legible. Replace if damaged.
Page 6
Skid Steer Shutdown Procedure
The following are basic skid steer shutdown procedures.
Follow these procedures and any additional shutdown
procedures provided in your skid steer Operator’s
Manual before leaving the operator’s seat.
1.
Reduce engine speed and shut-off all power to the
attachment.
2. Park on solid, level ground and lower attachment until
it is flat on the ground or on non-concrete support
blocks.
3. Turn off engine, and remove switch key to prevent
unauthorized starting.
4. Relieve all hydraulic pressure to auxiliary hydraulic
lines.
5. If included, raise seat bar and move controls until
both lock.
6. Wait for all components to come to a complete stop
before leaving the operator’s seat.
7.
Use steps, grab-handles and anti-slip surfaces when
stepping on and off the skid steer or attachment.
Make sure the intended skid steer conforms to the “Skid
Steer Requirements” stated above. Read and
understand the operator’s manual for your Road Saw. An
understanding of how it works will aid in the assembly
and setup of your saw.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
13
Table of Contents
Section 1: Assembly & Set-up
Dealer Set-up
72184
Lift Points
Refer to Figure 1-1 & Figure 1-2:
The Road Saw is shipped from the factory fully
assembled. Use a hoist or other suitable lift device to lift
the unit off the pallet and set it on the ground. Make sure
the Road Saw is secured before lifting it.
Use lift points shown on both sides of the Road Saw in
Figure 1-1 to pick up the SW3010.
Use lift points shown on both sides of the Road Saw in
Figure 1-2 to pick up the SW3018. Be careful not to
damage the manual storage tube.
Preform the following simple checks before operation
begins.
Safety Decals
Refer to pages 7-11:
The safety decals should be clearly readable and always
followed. Replace any decal that is missing or not
readable. Refer to “Safety Labels” on page 6.
Hydraulic Couplers
The hydraulic hoses on the Road Saws are shipped with
couplers. If the couplers do not fit the skid steer couplers,
the customer will need to obtain the correct style and size
to match the skid steer couplers and Road Saw hydraulic
hoses.
SW3010 Lift Points
Figure 1-1
72197
The pressure “in” port on the diverter valve is marked LP
for motor pressure. Return flow to the loader is marked
LR for motor return. The small hose is for drive motor
case drain and is connected directly to the skid steer
case drain coupler.
The Road Saws operate on the skid steer auxiliary
hydraulic flow. Since the auxiliary flow is reversible, be
sure to operate the unit with the cutting wheel spinning in
the direction the teeth are pointing.
Hydraulic Hoses and Fittings
All fittings should be tight and free of hydraulic leaks.
Hoses must be free of abrasion or cuts that might result
in leakage. Check the Road Saw before operation to
make sure all hose routings are kink-free and allow for
maximum movement of loader arms and tilt motion
required during normal operation.
Wire Harness
The wiring harness to the electro-hydraulic valve block
should be routed to prevent catching or pinching while
raising and lowering with the hitch tilted fully forward and
fully backward, while sideshifting, and while lowering the
cutting wheel fully into the cut.
14
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
Manual
Storage
Tube
SW3018 Lift Points
Figure 1-2
5/17/19
Table of Contents
Section 1: Assembly & Set-up
Cutting Wheel Assembly
For proper cutting wheel operation, picks must be
installed in every pick holder on the wheel.
Motor Case Drain
IMPORTANT: Do not operate the Road Saw without
connecting the case drain hose to the skid steer’s
case drain coupler. Not connecting case drain
coupler may cause severe damage to the hydraulic
motor.
IMPORTANT: Unobstructed case drain flow is
critical to proper motor operation. Blocked case
drain flow will damage the hydraulic motor.
NOTE: Unless a defect in the motor is found,
damage to the motor shaft seal and end cap gasket
are not covered under the warranty.
The Road Saws have a planetary gearbox mounted with
the cutting wheel which is driven by a hydraulic piston
motor.
During motor operation, some oil bypasses the motor
and must be allowed an unobstructed path back to the
skid steer hydraulic tank. If this flow is restricted,
pressure will build up inside the motor and will damage
the motor shaft seals and/or end cap gasket.
Several cases can lead to this damage:
• Pinched or crushed case drain hose can restrict flow.
• Disconnected case drain quick coupler will stop flow.
• Picks on the cutting wheel can come in contact with the
pavement or trailer ramps while the skid steer is in
motion, forcing the cutting wheel to rotate with the highflow hydraulic circuit “off”. This wheel rotation forces
the motor to turn, which pressurizes the motor’s case
because the pressure and return oil’s path have been
blocked.
If the above issues are not addressed, severe motor
damage may result. All of these issues can be attributed
to the operator and are preventable with proper
operation. Never operate the Road Saw without ensuring
the case drain hose is in good working order and properly
connected.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
15
Table of Contents
Section 2: Operating Procedures
Section 2: Operating Procedures
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the Road Saw. Therefore, it is absolutely
essential that no one operates the Road Saw unless they
are age 16 or older and have read, fully understood, and
are totally familiar with the Operator’s Manual and
equipment work site.
•
Keep body, body extremities, clothing, pull strings, etc.
away from rotating/moving parts. Always shut off
hydraulics to the attachment and shutdown the power
machine before adjusting or servicing the equipment.
•
Do not drive close to ditches, retaining walls, drop-offs,
water, etc. Rollover due to a cave-in or mishap could result.
•
Know weight limitations of operating surfaces and
clearances.
Perform the following inspections before using your Road
Saw.
Operating Checklist

Check
Page
Read & follow all safety rules & safety decals.
Refer to this manual and the attachment’s decals.
Make sure all guards and shields are in place and
the polycarbonate door is in good working order.
Read & follow preparation & setup instructions.
Refer to “Section 1: Assembly & Set-up”.
13
Read and follow all operating procedures.
Refer to “Section 2: Operating Procedures”.
16
Read & follow all maintenance Instructions.
Refer to “Section 4: Maintenance & Lubrication”.
28
Read & follow all lubrication instructions.
Refer to “Lubrication Points”.
33
Check initially and periodically for loose bolts and
pins. Refer to “Torque Values Chart”.
39
!
•
Avoid exposure to dust containing crystalline silica
particles. This dust can cause serious injury to the lungs
(silicosis). Because crystalline silica is a basic component
of sand and granite, many activities at construction sites
produce dust containing crystalline silica. Trenching,
sawing, and boring of material containing crystalline silica
can produce dust containing crystalline silica.
•
Do not operate the Road Saw with an open cab machine or
with a tempered front glass window/door on the machine.
We strongly recommend use of a polycarbonate front glass
door/window when operating the Road Saw.
•
Operate attachment from inside an enclosed cab or wear a
dust mask and eye protection. Flying dust and debris can
enter the lungs causing respiratory problems, enter the eyes
causing eye injury and /or cause bodily injury to the body of
people or animals.
•
Make sure safety labels are installed in their proper
location and are in good condition before operating the
attachment. Read and obey all instructions on the labels.
•
Refer to the safety section of your skid steer Operator’s
Manual and observe all safety recommendations set forth in
the manual.
•
Use steps, grab-handles, and anti-slip surfaces on the
power machine and attachment to get on and off the power
machine. Using unapproved stepping surfaces and/or
handholds can result in a falling hazard.
•
Allow only persons to operate this attachment who have
fully read and comprehended this manual, who are properly
trained to operate the attachment safely, and who are age 16
or older. Serious injury or death can result from the failure
to read, understand, and follow instructions provided in this
manual.
•
Operate only power machines equipped with a certified
Roll-Over Protective Structure (ROPS) and seat belt.
Fasten seat belt snugly and securely to help protect against
serious injury or death from machine overturn.
•
Backup alarm must be in good working order to warn
others. Use a backup camera or rear-view mirror that is in
good condition to help see undesirable situations behind the
unit. Drive at a slower speed to compensate for blind spots.
General Safety Information
Exposed moving parts are guarded whenever possible
for safety. However, not all moving parts can be shielded
in order to ensure proper operation. This Operator’s
Manual and safety decals on the machine provide
important safety information. Read and follow their
directions. If a safety decal becomes difficult to read,
replace it immediately.
! DANGER
To avoid serious injury or death:
•
Do not let children play on or around the attachment
including when stored. Children and/or attachment can fall.
•
Do not allow anyone near the power machine or attachment
while operating. Stop operation if bystanders are too close.
They can be hit by flying projectiles or become entangled,
crushed, or ran over by the equipment.
•
Never crawl under raised loader arms unless properly
secured. Fully lower loader arms or have the loader arms
secured in the raised position with an approved lift-arm
support before leaving the skid steer seat. Crawling under
unsupported loader arms can cause a crushing hazard.
•
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment
supported by concrete blocks or hydraulics. Concrete can
break, hydraulic lines can burst, and/or hydraulic controls
can be actuated even when power to hydraulics is off.
16
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
WARNING
To avoid serious injury or death:
• All guards and shields must be installed and in good
working condition while operating the attachment. Never
operate the Road Saw with the access door open.
5/17/19
Table of Contents
Section 2: Operating Procedures
•
Make sure controls are all in neutral position or park before
starting the power machine.
•
Always operate attachment while seated with seat belt
fastened around operator. Always lower seat/lap bar(s)
when equipped with the skid steer. This will help protect the
operator against sudden stops when hitting solid objects.
•
Never carry riders on the attachment or power machine.
Riders can obstruct the operator’s view, interfere with
control of the equipment, be pinched by moving
components, become entangled in rotating components, be
struck by objects, be thrown or fall from the equipment, etc.
•
Always shut power machine down using the “Shutdown
Procedure” provided in this manual before servicing,
adjusting, cleaning, or maintaining the attachment.
•
Never allow hands or feet near any working part of the
attachment unless the mandatory power machine shutdown
procedure has been completed.
•
Check hitch fit-up frequently. An improper fit-up can cause
the attachment to come loose from the loader hitch plate
and fall.
•
Do not cut anything other than asphalt or light concrete.
Doing so can cause a thrown object hazard or damage the
Road Saw.
•
Never make contact with underground utilities such as
electrical power lines, gas lines, phone lines, etc. They can
cause serious injury or death from electrocution, explosion,
or fire. If in doubt, call 811 (USA) before digging so that
they can mark the location of underground services in the
area. For contact information, see Dig Safe in the
“Important Safety Information” starting on page 1.
•
Always exercise safety, courtesy, and common sense. Be
aware of pedestrian and vehicle traffic. Check blind spots
before moving. Use Road Saw during low-traffic hours.
•
Keep body, body extremities, loose clothing, pull strings,
etc. away from pinch points such as rotating, extending,
and/or retracting components. Secure pinch point areas to
ensure they will not move before working on or near them.
•
Do not use attachment to lift, carry, push or tow other
equipment and objects. It is not properly designed or
guarded for this use. The operator could lose control and
cause a tipping hazard.
•
Do not alter attachment or replace parts on the attachment
with other brands. Other brands may not fit properly or
meet OEM specifications. They can weaken the integrity
and impair the safety, function, performance, and life of the
attachment. Replace parts only with genuine OEM parts.
•
Hydraulic fluid under high pressure can penetrate the skin
and/or eyes causing a serious injury. Wear protective gloves
and safety glasses or goggles when working with hydraulic
systems. Use a piece of cardboard or wood rather than
hands when searching for leaks. A doctor familiar with this
type of injury must treat the injury within a few hours or
gangrene may result. DO NOT DELAY.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
17
Table of Contents
Section 2: Operating Procedures
Hook-up Road Saw
72198
Refer to Figure 2-1:
!
DANGER
!
WARNING
To avoid serious injury or death: A crushing hazard exists
while hooking-up and unhooking the attachment. Do not allow
anyone to stand between attachment and power machine while
approaching or backing away from the attachment. Do not
operate lift and/or tilt controls while someone is near the
power machine and/or attachment.
To avoid serious injury or death:
• Check hitch fit-up frequently. An improper fit-up can cause
the attachment to come loose from the loader hitch plate
and fall.
•
Use steps, grab-handles, and anti-slip surfaces on the
power machine and attachment to get on and off the power
machine. Using unapproved stepping surfaces and/or
handholds can result in a falling hazard.
1.
Check skid steer and Road Saw hitch plates before
hooking-up the Road Saw. Make sure all hitch
components are in good working condition:
a. Check for and remove any debris in the loader
and Road Saw hitch plates.
b. Check hitch plates for structural cracks and bent
or broken pieces. They can weaken a hitch plate
and prevent full and complete hook-up. Repair or
replace damaged hitch plates before putting the
Road Saw into service.
c. Check operation of lock pins in the loader hitch
plate. Lock pins must move freely and extend fully
into the bottom slots in the Road Saw hitch plate.
d. Check hydraulic hoses for pinch points and
clearances. Make sure hydraulic hoses will not
interfere with hitch hook-up.
2. If lock mechanism is mechanical, raise lock handles
on the loader hitch plate fully up to raise lock pins.
3. Start skid steer.
Bottom Slot
Top Angle Bar
Bottom Slot
Hook-up Road Saw
Figure 2-1
9. Engage lock mechanism:
Hydraulic Lock Mechanism :
a. Engage quick hitch locking mechanism
hydraulically.
Mechanical Lock Mechanism:
a. Shut skid steer down before dismounting.
Refer to “Skid Steer Shutdown Procedure” on
page 13.
b. Push lock handles down to drive lock pins through
bottom slots in the Road Saw hitch plate. Make
sure handles are locked down.
c. Return to skid steer and start.
10. Raise loader arms enough to visually ensure lock
pins are through the bottom slots on the Road Saw.
11. Shut skid steer down before dismounting. Refer to
“Skid Steer Shutdown Procedure” on page 13.
4. If lock mechanism is hydraulic, use auxiliary
hydraulic controls to raise lock pins fully up.
5. Drive slowly to the Road Saw hitch plate while
making sure the loader hitch is parallel with the top
angle bar on the Road Saw hitch plate.
6. Tilt top of loader hitch plate slightly forward.
7.
Place top of loader hitch plate under the Road Saw
top angled bar and slowly raise loader arms up until
loader hitch plate is seated under the top angle bar.
8. Tilt top of loader hitch plate back until the Road Saw
hitch plate makes full contact with loader hitch plate
and the Road Saw is slightly off the ground.
18
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 2: Operating Procedures
72154
Hydraulic Schematic
Figure 2-2
Hydraulic Hose Hook-up
!
WARNING
To avoid serious injury or death:
• Hydraulic fluid under high pressure can penetrate the skin
and/or eyes causing a serious injury. Wear protective gloves
and safety glasses or goggles when working with hydraulic
systems. Use a piece of cardboard or wood rather than
hands when searching for leaks. A doctor familiar with this
type of injury must treat the injury within a few hours or
gangrene may result. DO NOT DELAY.
•
•
Shut power machine down and release all hydraulic
pressure to the equipment before connecting or
disconnecting hydraulic hoses to or from the power
machine.
Make sure hydraulic flow to the Road Saw does not exceed
maximum rated flow listed in the specifications on page 36.
Exceeding maximum flow will increase rotor speed and
result in a thrown object hazard.
IMPORTANT: Make sure coupler fittings are clean
before making connections. Dirt can quickly damage
the hydraulic system. Inspect couplers for corrosion,
cracks and excessive wear. Replace couplers if any
of these conditions exist.
Refer to Figure 2-2:
1. Clean quick connect couplers of dirt and then
connect female and male coupler to the skid steer’s
auxiliary outlets. Make sure quick connect couplers
have fully engaged. If they have not, check the
following to make sure:
a. Couplers are same size and type.
b. Auxiliary hydraulic pressure to the loader couplers
has been released.
2. Hook-up case drain hydraulic hose coupler to the
skid steer’s case drain coupler.
3. For additional help, refer to Hydraulic Hook-up in
your skid steer Operator’s Manual.
IMPORTANT: All hoses should be free of kinks, cuts,
or abrasions for safe operation. Do not operate if
hoses are worn or damaged.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
19
Table of Contents
Section 2: Operating Procedures
72151
CONNECT TO WHITE WIRE
ON WIRE HARNESS #106-6440
CONNECT TO GREEN WIRE
ON WIRE HARNESS #106-6440
CONNECT TO RED WIRE
ON WIRE HARNESS #106-6440
CONNECT TO BLUE WIRE
ON WIRE HARNESS #106-6440
NOT USED
NOT USED
Solenoid Valve Part No. 106-6330
Figure 2-4
Electrical Hook-up
Refer to Figure 2-4 & Figure 2-5 on page 21:
1. Attach adapter wire harness #106-6440 to solenoid
valve #106-6330. Make sure wire colors are matched
with the stated color for each connector on the valve.
Refer to Figure 2-5 & Figure 2-6 on page 21:
2. Attach main wire harness #106-0647 to adapter wire
harness #106-6440. Make sure wire colors are
matched at each connection.
3. Connect main wire harness to the skid steer pin
connector.
4. Make sure the main wire harness is routed to prevent
it from catching or pinching while sideshifting, tilting
the hitch plate, or fully lowering the cutting wheel.
20
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 2: Operating Procedures
72201
DIODE PACK B
#106-6342
DIODE PACK A
#106-6341
DEUTSCH
#DT04-12PA
DEUTSCH
#DT04-2P
DEPTH UP
DARK-BLUE WIRE
WITH BLUE ZIP TIE
DEUTSCH
#DT06-12SA
DEUTSCH
#DT04-12PA
DEUTSCH
#DT06-12SA
DEUTSCH DT06-2S
W/ WHITE WIRE
DEUTSCH DT06-2S
W/ RED WIRE
DEPTH DOWN
LIGHT-BLUE WIRE
WITH Orange ZIP TIE
SIDESHIFT LEFT
DARK-BROWN WIRE
WITH BROWN ZIP TIE
DEUTSCH DT06-2S
W/ BLUE WIRE
SIDESHIFT RIGHT
LIGHT-BROWN WIRE
WITH WHITE ZIP TIE
DEUTSCH DT06-2S
W/ GREEN WIRE
Connects to Solenoid Valve #106-6330
Connects to Wire Harness #106-0647
Adapter Wire Harness #106-6440
Figure 2-5
72152
DT06-2S Connects to Wire Harness #106-6340
HDR36-18-14SN-059
DARK BLUE
DEPTH UP
DARK-BLUE WIRE
LABEL: C1A
E-DEPTH UP
DT06-2S
LIGHT BLUE
F-DEPTH DN
DARK GREEN
C-NOT USED
LIGHT GREEN
DEPTH DOWN
LIGHT-BLUE WIRE
LABEL: C1B
D-NOT USED
DT06-2S
DARK BROWN
G-SIDESHIFT LEFT
LIGHT BROWN
H-SIDESHIFT RIGHT
NOT USED
DARK-GREEN WIRE
LABEL: C2A
A-NOT USED
DT06-2S
J-NOT USED
BLACK
B-GROUND
NOT USED
LIGHT-GREEN WIRE
LABEL: C2B
K-NOT USED
DT06-2S
L-NOT USED
M-NOT USED
SIDESHIFT LEFT
DARK-BROWN WIRE
LABEL: C3A
SIDESHIFT RIGHT
LIGHT-BROWN WIRE
LABEL: C3B
N-NOT USED
DT06-2S
P-NOT USED
DT06-2S
Electrical Schematic for Main Wire Harness Part #106-0647
Figure 2-6
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
21
Table of Contents
Section 2: Operating Procedures
Pre-Operation Inspection
! WARNING
To avoid serious injury or death:
•
Do not operate the Road Saw with an open cab machine or
with a tempered front glass window/door on the machine.
We strongly recommend use of a polycarbonate front glass
door/window when operating the Road Saw.
•
Backup alarm must be in good working order to warn
others. Use a backup camera or rear-view mirror that is in
good condition to help see undesirable situations behind the
unit. Drive at a slower speed to compensate for blind spots.
1.
Shut skid steer and Road Saw down. Follow “Skid
Steer Shutdown Procedure” on page 13.
2. Complete “Operating Checklist” on page 16.
3. Make sure the skid steer is equipped with an operator
safety enclosure. We strongly recommend the cab
be equipped with a polycarbonate door, which may
have been supplied with the skid steer.
4. If attachment is to be operated in reverse, make sure
visibility to the rear of the power unit is appropriate
for the attachment. Backup camera or mirror is
recommended. Maintain cleanliness of lens or
mirror.
5. Inspect attachment’s safety equipment to make sure
it is in good working condition and that all safety alert
decals are visible and legible. Replace all missing
and/or illegible safety alert decals. See “Safety
Labels” on page 6.
6. Check skid steer and Road Saw hitch plates. Make
sure all hitch components are in good working
condition:
a. Check for and remove any debris in the loader
and Road Saw hitch plates.
b. Check hitch plates for structural cracks that can
weaken the hitch plates and result in dropping the
attachment. Check for bent plates that will prevent
full and complete hook-up. Repair or replace
damaged hitch plates before putting the Road
Saw into service.
c. Check operation of lock pins in the loader hitch
plate. Lock pins must move freely and extend fully
into the bottom slots in the Road Saw hitch plate.
d. Check hydraulic hoses for pinch points and
clearances. Make sure hydraulic hoses will not
interfere with hitch hook-up.
7.
Consult your skid steer Operator’s Manual to
determine if rear ballast is required. Add ballast if
necessary.
8. Visually check for excessive wear, worn, damaged,
cracked, or loose parts. Replace parts with genuine
Kubota parts.
9. Inspect condition of hydraulic hoses, fittings, and
valves before starting the skid steer. Make sure
22
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
hoses are not twisted or frayed and will not get
pinched, kinked, or stretched.
10. Start skid steer and check hydraulic oil leaks with a
piece of paper or cardboard. Do not use your hands
as invisible thin streams of high pressure oil can be
injected into your skin. See “Avoid High Pressure
Fluids Hazard” on page 3.
11. Check all controls and operating functions of the skid
steer.
12. Operate the Road Saw through its full range of
movements to check for clearances. Refer to “Check
Equipment Clearances” on this page.
Check Equipment Clearances
It is important to check equipment clearances and
hydraulic hose routing before putting the Road Saw into
operation. Carefully go through the Road Saw’s full range
of motions to make sure the saw does not make contact
with the skid steer frame, tires, and hydraulic hoses.
Check hydraulic hoses to make sure they do not stretch,
kink, or pinch.
!
WARNING
To avoid serious injury or death:
• Use steps, grab-handles, and anti-slip surfaces on the
power machine and attachment to get on and off the power
machine. Using unapproved stepping surfaces and/or
handholds can result in a falling hazard.
•
Check hitch fit-up frequently. An improper fit-up can cause
the attachment to come loose from the loader hitch plate
and fall.
1.
Before starting the skid steer, check hitch hook-up.
The attachment can fall from the loader hitch plate if
not properly connected.
a. Make sure loader hitch is fully seated under the
Road Saw’s top angle bar.
b. Make sure loader hitch plate is against the Road
Saw hitch plate.
c. Make sure lock handles or hydraulic locks are
locked with lock pins fully seated in the bottom
slots.
2. If necessary, have someone stand nearby but at a
safe distance that can motion for the operator to stop
if a problem develops.
3. With the Road Saw on the ground, start skid steer
and carefully rotate the top of the loader hitch plate
fully back while watching hydraulic hoses to make
sure they do not become pinched or kinked.
4. Carefully raise loader arms up while tilting the top of
the hitch fully forward to rotate the front of the Road
Saw down. Watch hydraulic hoses to make sure they
do not stretch, pinch, or kink.
5. Continue to raise loader arms fully up and tilt the
loader hitch fully forward while watching to make sure
5/17/19
Table of Contents
Section 2: Operating Procedures
the attachment does not make contact with the skid
steer or skid tires. Watch hydraulic hoses to make
sure they do not stretch, pinch, or kink.
72123
6. Rotate top of hitch plate back and lower loader arms
until Road Saw is resting on the ground.
7.
Shut skid steer down before dismounting. Refer to
“Skid Steer Shutdown Procedure” on page 13.
8. Recheck hydraulic hoses. If needed, add zip ties to
the hoses to protect them from possible damage.
Basic Operation
IMPORTANT: Insufficient hydraulic power will result
in poor performance. Check pressure and flow per
factory skid steer specifications.
NOTE: Cutting speed will depend on pick condition,
age and density of the material, aggregate size, and
ambient temperature.
Before operating the attachment, read this entire manual.
Follow all safety guidelines in this manual and safety
decals on the unit. Make sure that all guards, shields, and
decals are in place and in good condition prior to
operation.
SW3010 Hydraulic Operation
Figure 2-7
Operating the SW3010
See specifications in this manual for minimum and
maximum pressures and flow requirements for your
machine. Make sure the skid steer hydraulic pressure
ratings fall within the specified range.
Refer to Figure 2-7:
1. Enter skid steer and fasten seat belt.
The Road Saw is a hydraulically powered attachment
intended for milling cuts in asphalt or light concrete
surfaces. The performance of the attachment can vary
greatly depending upon how it is used and operated. The
recommended operation procedures in this manual
should be followed at all times for maximum productivity.
3. Start skid steer and engage high flow hydraulic circuit
at an idle.
Productivity can vary greatly depending on cutting depth,
type of aggregate in the mix, ambient temperature, and
condition of the picks.
5. Move throttle to full rpm position and make the
following adjustments using the electrical and
hydraulic controls.
Picks should be inspected every 30 minutes for wear and
to make sure they are rotating freely in their holders.
Replace worn picks immediately. To promote pick
rotation, spray picks daily with a water based asphalt
emulsifier to break down asphalt emulsion. (Example:
Zep’s part #AR6690) See the maintenance section for
more information.
Optional picks for cutting concrete and Water Spray Kits
are available. Water Spray Kits increase productivity by
suppressing dust and helping picks rotate properly.
If attachment is to be operated in reverse, make sure
visibility to the rear of the power unit is appropriate for the
attachment. Backup camera or mirror is recommended.
Maintain cleanliness of lens or mirror.
2. Make sure the area is clear of bystanders.
IMPORTANT: To prevent damaging the Road Saw,
raise the unit off the ground before sideshifting.
4. Raise Road Saw fully off the ground.
a. Adjust saw depth to 0 with hydraulic cylinder (#1)
while using depth gauge (#2) as a guide.
b. Engage hydraulic cylinder (#3) to sideshift the
saw.
6. Fully lower loader arms and tilt top of hitch plate until
the Road Saw is level with the pavement.
7.
Keep the throttle at a full rpm position during cutting
operations.
8. Using depth cylinder (#1), slowly lower the cutting
wheel into the cut to the desired depth.
9. Begin moving forward at a speed that will allow the
saw to cut efficiently without stalling. Cutting speed
will depend on depth, density, and material being cut.
Do not turn while cutting. Cut straight lines only. Cutting
curves will quickly wear the picks located along the edge
of the cutting wheel and decrease productivity. Cutting a
radius or curve can also damage the cutting wheel.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
23
Table of Contents
Section 2: Operating Procedures
Transporting
72000
!
WARNING
To avoid serious injury or death:
When traveling on roadways, transport in such a way that
other vehicles may pass you safely. Use accessory lights, clean
reflectors, and a slow moving vehicle sign that is visible from
the back to warn operators in other vehicles of your presence.
Always comply with all federal, state, and local laws.
1.
Be sure to reduce ground speed when turning. Leave
enough clearance to keep the attachment from
making contact with obstacles such as buildings,
trees or fences.
2. Select a safe ground speed when transporting from
one area to another.
3. When traveling on public roadways, transport in such
a way that faster moving vehicles may pass you
safely. A slow moving vehicle sign should always be
properly displayed when traveling on public roads or
right-of ways.
4. Decrease transport speed when traveling over rough
or hilly terrain.
SW3018 Hydraulic Operation
Figure 2-8
Operating the SW3018
Refer to Figure 2-8:
1. Enter skid steer and fasten seat belt.
2. Make sure the area is clear of bystanders.
3. Start skid steer and engage high flow hydraulic circuit
at an idle.
5. When transporting skid steer on a trailer:
• Use towing vehicle and trailer of adequate
capacity.
• Always drive up a ramp with heavy end uphill.
• Shut skid steer down before dismounting. Follow
“Skid Steer Shutdown Procedure” on page 13.
• Secure skid steer loader and attachment using tie
downs and chains.
IMPORTANT: To prevent damaging the Road Saw,
raise the unit off the ground before sideshifting.
4. Raise Road Saw fully off the ground.
5. With skid steer operating at an idle, make the
following adjustments using the electrical and
hydraulic controls.
a. Adjust saw depth to 0 with hydraulic cylinder (#1)
while using depth gauge (#2) as a guide.
b. Engage hydraulic cylinder (#3) to sideshift the
saw.
6. Fully lower loader arms and tilt top of hitch plate until
the Road Saw is level with the pavement.
7.
Move throttle to full rpm position. Keep throttle at full
rpm during cutting operations.
8. Using depth cylinder (#1), slowly lower the cutting
wheel into the cut to the desired depth.
9. Begin moving forward at a speed that will allow the
saw to cut efficiently without stalling. Cutting speed
will depend on depth, density, and material being cut.
24
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 2: Operating Procedures
72198
Bottom Slot
Top Angle Bar
Bottom Slot
Unhook Road Saw
Figure 2-9
Unhook Road Saw
Refer to “Figure 2-9” on page 25:
1. Park skid steer with Road Saw on a flat, level surface.
Lower loader arms until Road Saw is resting on the
ground.
2. Shut skid steer down before dismounting. Follow
“Skid Steer Shutdown Procedure” on page 13.
3. Disconnect hydraulic hoses. It will be necessary to
release hydraulic pressure in the lines before hoses
will disconnect from the skid steer. Coil hydraulic
hoses and store them on the Road Saw with hose
ends out of the dirt.
4. Disconnect wire harness from the skid steer. Coil
wire harness up and store on the Road Saw with the
plug end hanging down to keep moisture and dirt out.
5. If lock handles are mechanical, pull lock handles up
on the loader hitch plate to remove lock pins from the
bottom slots in the attachment’s hitch plate.
6. Return to the skid steer seat and fasten seat belt.
7.
Start skid steer.
8. If lock handles are hydraulic, raise lock pins
hydraulically to remove them from the hitch plate
slots.
9. Tilt loader hitch plate slightly forward until the bottom
of the loader hitch plate has separated away from the
bottom of the Road Saw hitch plate.
10. Slowly lower loader arms until the loader hitch plate
has separated from the attachment’s top angle bars.
11. Back skid steer slowly away from the planer making
sure the skid steer does not interfere with the
attachment’s hitch plate, hydraulic hoses, or wire
harness.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
25
Table of Contents
Section 3: Options & Accessories
Section 3: Options & Accessories
Picks (Accessory)
The factory installed carbide picks are a general purpose
pick and are designed for cutting both asphalt and
concrete. Picks designed for extended periods of
concrete cutting are available from your dealer.
Part No.
If needed, Locate & Cut
Notches in Door For
U-bolts Clearance.
Description
Hook Elastic Tie-Down
To Skid Steer Cage To
Keep Door Closed.
106-3142
Pick, Asphalt (See Notes 1 & 2)
106-3133
Pick, Concrete (Accessory) See Note 1
Note 1: Factory Installed.
Note 2: Total quantity of picks required per cutting wheel
varies from model to model. See Model number and
quantities listed below.
SW3010-2.5 . . . 26 ea.
SW3010-4.5 . . . 34 ea.
SW3018-3.0 . . . 30 ea.
SW3018-4.5 . . . 48 ea.
SW3018-6.0 . . . 60 ea.
If Needed, Locate &
Cut Notch in Door
To Clear Skid Steer
Frame.
Skid Steer
Hand Hold
Water Spray Kit (Accessory)
Use Water Spray Kit provided by Kubota to increase pick
life by 20% to 40% and to suppress milling dust. Water
Spray Kits are available from your dealer. Order 1 Water
Tank Kit and 1 Spray Bar Kit that matches the Road Saw
model.
Part No.
Description
350-378A
350-390A
Water Tank Kit, SW30
Spray Bar Kit, SW3010 & SW3018
24608
Operator Protective Door
Figure 3-1
Operator Protective Door (Optional)
Refer to Figure 3-1:
A polycarbonate door is recommended. If your skid steer
does not have a polycarbonate door, the optional
polycarbonate door below may be purchased to enclose
the front of your skid steer cab.
Protective Door Assembly . . . . . . . . . . . . . . . . . . . 326-024A
!
WARNING
Do not drill holes in the ROPS (Roll Over Protection System)
to attach this Operator Protective Door. Drilling unapproved
holes in the ROPS can weaken the structure.
Instructions below should only be used when installing
this optional Operator Protective Door #328-024A.
1.
Cut notches in the protective door as needed to
provide clearance around u-bolts and skid steer
frame.
2. Install Protective Door to the skid steer’s hand hold
with two u-bolts (#3), flat bars (#2), and four nuts (#1)
as shown. Tighten nuts to correct torque.
26
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 3: Options & Accessories
This page left blank intentionally.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
27
Table of Contents
Section 4: Maintenance & Lubrication
Section 4: Maintenance & Lubrication
Maintenance
•
Proper servicing and adjustment are key to the long life of
any attachment. With careful and systematic inspection,
you can avoid costly maintenance, time, and repair.
Check hitch fit-up frequently. An improper fit-up can cause
the attachment to come loose from the loader hitch plate
and fall.
•
Hydraulic fluid heats up when the skid steer is operating.
This can cause hydraulic hoses, fittings, and couplers to
become hot. Wear gloves when working with hydraulic
components and when connecting and disconnecting
hydraulic couplers.
Check all bolts after using the unit for several hours to be
sure they are tight. Replace any worn, damaged, or
illegible safety labels by obtaining new labels from your
Kubota dealer.
! DANGER
To avoid serious injury or death:
•
Do not go near or under raised loader arms without first
securing loader arms in the raised position with an
approved lift-arm support.
•
Keep body, body extremities, clothing, pull strings, etc.
away from rotating/moving parts. Always shut off
hydraulics to the attachment and shutdown the power
machine before adjusting or servicing the equipment.
•
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment
supported by concrete blocks or hydraulics. Concrete can
break, hydraulic lines can burst, and/or hydraulic controls
can be actuated even when power to hydraulics is off.
! WARNING
To avoid serious injury or death:
•
Always shut power machine down using the “Shutdown
Procedure” provided in this manual before servicing,
adjusting, cleaning, or maintaining the attachment.
•
Allow only persons to perform maintenance on this
attachment who have been properly trained in its safe
operation.
•
Keep body, body extremities, loose clothing, pull strings,
etc. away from pinch points such as rotating, extending,
and/or retracting components. Secure pinch point areas to
ensure they will not move before working on or near them.
•
Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting implement
back into service.
•
Backup alarm must be in good working order to warn
others. Use a backup camera or rear-view mirror that is in
good condition to help see undesirable situations behind the
unit. Drive at a slower speed to compensate for blind spots.
Servicing Drivetrain Components
Detailed repair of the drivetrain components such as the
hydraulic motor and gearbox are not covered in this
manual. Contact your Kubota dealer for information
about repairing these components during the warranty
period.
Any unauthorized work performed on these components
during the warranty period may void your warranty.
Cutting Wheel Maintenance
Cutting wheel maintenance is critical to extending the life
of the pick, pick holder, and overall productivity of the
Road Saw.
IMPORTANT: Inspect cutting wheel picks and
pick holders every 30 minutes of operation.
The factory installed carbide picks are a general purpose
pick and are designed for milling cuts in asphalt and light
concrete. Picks designed for extended periods of
concrete cutting are available from your dealer. Refer to
“Picks (Accessory)” on page 26.
Pick life varies with depth, density, material, aggregate,
and maintenance. To maximize pick life, the picks must
be free to rotate in the holder.
The pick has two functions:
• Serve as a consumable cutting tool.
• Protect the holder.
If the pick is not free to rotate in the holder or if the pick
locks up in the holder, pick and pick holder wear is greatly
accelerated.
Edge picks wear faster than center picks due to side
loading of the cutting wheel during the power unit’s
steering corrections.
To promote pick rotation in the holder, spray picks daily
with a water based asphalt emulsifier to break down
asphalt emulsion. (Example: Zep’s part #AR6690)
•
Do not alter attachment or replace parts on the attachment
with other brands. Other brands may not fit properly or
meet OEM specifications. They can weaken the integrity
and impair the safety, function, performance, and life of the
attachment. Replace parts only with genuine OEM parts.
•
Check hydraulic hoses and fittings frequently for leaks or
damage. Fluid escaping under pressure can penetrate skin.
Large leaks can drop the attachment.
Use Water Spray Kit provided by Kubota to increase pick
life by 20% to 40% and to suppress milling dust. Refer to
“Water Spray Kit (Accessory)” on page 26.
•
Lubricate, make adjustments and repairs in a safe area
away from traffic and other hazards.
Figure 4-1 and Figure 4-3 on page 29 show examples of
excessively worn picks.
28
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
If the pick remains in the holder beyond the intended
replacement point, it reduces cutting performance and
will not protect the holder. If the picks are worn enough to
indicate slight holder wear, replace pick immediately.
5/17/19
Table of Contents
Section 4: Maintenance & Lubrication
72101
Examples of remaining pick life (%)
100
95
75
90
Rotating Picks
40
20
0
-5
Non-Rotating Picks
Picks may last twice as long if they are free to rotate in their holder
Varying Degrees of Pick Wear
Figure 4-1
72149
72100
Pick is no longer rotating in the holder,
causing premature pick and holder wear.
Fork Pick Tool
Figure 4-2
Remove & Install Picks
Refer to Figure 4-2:
!
WARNING
To avoid serious injury or death:
• Never strike a pick on the carbide tip. The carbide can
break or chip and cause injury.
•
Always wear eye protection when removing and installing
picks. Carbide picks can shatter causing injury.
A fork type pick tool (#1) is included with the Road Saw
and should be used to remove picks from the holders.
Insert the fork into the groove on the pick and strike the
tool with a hammer. In the event the pick tool is not
available, a punch can be inserted into the bottom of the
pick holders and tapped on the underside of the pick to
dislodge it.
For installation, the fork type tool should be inserted into
the groove on the pick and struck with a hammer. If the
tool is not available, a length of pipe with a 3/4 to 1 inch
inside diameter can be placed over the pick to protect the
5/17/19
Results of a Non-Rotating Pick
Figure 4-3
carbide pick from a direct hit. Striking a small piece of
wood placed on top the pipe to absorb the shock will also
help prevent damage to the pick and pick holder.
Pick Holder Repair
Refer to Figure 4-3:
IMPORTANT: To avoid bearing damage, always
ground directly to the cutting wheel before welding.
IMPORTANT: Kubota does not warrant any ground
engaging parts (cutting wheel, picks, holders, or
bases) against wear, unless the wear is determined
by Kubota to have been caused by a manufacturing
defect.
If a pick holder becomes worn, note the position and
angle of the holder. Cut the pick holder from the wheel
using a torch or air-arc. Weld the new holder to the wheel
in the noted position.
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
29
Table of Contents
Section 4: Maintenance & Lubrication
72194
72108
Fill Plug
Large Fill Plug
Planetary Gearbox
Planetary Gearbox
Motor
Motor
Small Oil Level Plug
Oil Level Plug
Large Drain Plug
Drain Plug
SW3010 Planetary Gearbox
Figure 4-4
SW3018 Planetary Gearbox
Figure 4-5
SW3010 Gearbox Oil Change
SW3018 Gearbox Oil Change
Refer to Figure 4-4:
The planetary gearbox oil should be drained and refilled
at 100 hours of operation and every 250 hours or yearly,
whichever comes first, after initial oil change.
Refer to Figure 4-5:
The planetary gearbox oil should be drained and refilled
at 100 hours of operation and every 250 hours or yearly,
whichever comes first, after initial oil change.
The planetary gearbox contains synthetic EP90 gear oil
and should be half full during operation.
The planetary gearbox contains synthetic EP90 gear oil
and should be half full during operation.
Oil drain and fill procedure:
Oil drain and fill procedure:
1.
1.
Shutdown skid steer before dismounting. Refer to
“Skid Steer Shutdown Procedure” on page 13.
2. Clean area around plug holes on gearbox.
Lower loader arms fully down and tilt top of hitch
plate to position the small oil level plug horizontal with
the gearbox center line.
3. Place an approved oil container under the gearbox
drain plug.
2. Shut skid steer down before dismounting. Refer to
“Skid Steer Shutdown Procedure” on page 13.
4. Remove the two drain plugs on the gearbox. Rotate
cutting wheel so that a plug hole is on the bottom to
drain the gearbox of oil.
3. Clean area around the 3 plug holes located on the
face of the gearbox near the motor.
5. Rotate cutting wheel and gearbox until one plug hole
is horizontal and the other plug hole is on top.
6. Slowly fill gearbox though the top fill hole until oil
reaches the horizontal oil level hole.
7.
The gearbox should be half full of AGMA EP90
synthetic gear lubricant or SAE 75W90 synthetic
gear lubricant. (Chevron RPM Synthetic 75W90 for
example). The approximate volume of the gearbox is
30 oz.
8. Replace the two gearbox plugs and tighten.
4. Place an approved oil container under the gearbox
large drain plug.
5. Remove the large drain plug located under the motor.
6. Remove the large fill plug located above the motor.
7.
Replace and tighten the drain plug after the oil has
finished draining out of the gearbox.
8. Remove the small oil level plug located to one side of
the motor.
9. The gearbox should be filled half full of AGMA EP90
synthetic gear lubricant or SAE 75W90 synthetic
gear lubricant. (Chevron RPM Synthetic 75W90 for
example). The approximate volume of the gearbox is
52 oz (1.5L).
10. Slowly fill gearbox though the top fill hole until oil
starts to come out the horizontal small oil level hole.
11. Replace oil fill plug and oil level plug. Tighten plugs.
30
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 4: Maintenance & Lubrication
72205
72206
10 11
Torque SW3018 Wheel Mounting Bolts (#10)
Figure 4-7
SW3010 Wheel Mounting Nuts
Refer to Figure 4-8 & Figure 4-9:
NOTE: The nine 5/8"-11 wheel mounting nuts (#3)
do not require a regular torque check. They do
require a normal maintenance inspection
1.
Remove SW3018 Front Guard
Figure 4-6
SW3018 Wheel Mounting Bolts
Release front chassis shroud latch (#1) and rotate
front chassis shroud (#2) open.
2. Inspect nuts (#3) and washers (#4) to make sure they
are not missing and all nuts are tight. Tighten loose
nuts to 220-250 ft-lbs (298-239 Nm).
72268
Refer to Figure 4-7:
The eight bolts (#10) connecting the wheel to the
gearbox spindle are to be torqued after 5 hours of
operation and then every 40 hours.
Refer to Figure 4-6:
1. Set saw at 0 depth and shut skid steer down. Refer to
“Skid Steer Shutdown Procedure” on page 13.
2. Remove bolts (#1) and flat washers (#2). Set
removed hardware aside for reuse.
3. Remove chassis retainer plate (#3), chassis spacer
plate (#4), chassis plastic spacer (#5), and spacer
plate (#6). Set removed hardware aside for reuse.
Open SW3010 Front Guard
Figure 4-8
4. Remove e-clip (#7). Set e-clip aside for reuse.
5. Return to the skid steer and tilt top of hitch plate fully
back and then raise the Road Saw up until the front of
side cover (#8) clears chassis (#9).
72268
6. Have a person place a support block under the hitch
plate to keep the loader arms from going down.
7.
Shut skid steer down before dismounting. Refer to
“Skid Steer Shutdown Procedure” on page 13.
8. Remove side cover (#8) and set aside for reuse.
Refer to Figure 4-6 & Figure 4-7:
9. Access wheel bolts (#10) and flat washers (#11) from
front of chassis (#9). Torque bolts (#10) to
220-250 ft-lbs (298-239 Nm).
10. Reinstall side cover (#8).
Inspect SW3010 Wheel Mounting Nuts (#3)
Figure 4-9
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
31
Table of Contents
Section 4: Maintenance & Lubrication
Long-Term Storage
6. Replace all damaged or missing decals.
Clean, inspect, service, and make necessary repairs to
the Road Saw when parking it for long periods and when
parking it at the end of a working season. This will help
ensure that the Road Saw is ready for field use the next
time you hook-up to it.
7.
!
DANGER
!
WARNING
Lubricate as noted under “Lubrication Points” on
page 33.
8. A light coat of oil or grease may be applied to
exposed cylinder rods to minimize oxidation.
9. Store Road Saw on a level surface in a clean, dry
place. Inside storage will reduce maintenance and
make for a longer Road Saw life.
To avoid serious injury or death:
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment supported
by concrete blocks or hydraulics. Concrete can break,
hydraulic lines can burst, and/or hydraulic controls can be
actuated even when power to hydraulics is off.
To avoid serious injury or death:
• Always shut power machine down following the “Shutdown
Procedure” provided in this manual before leaving the
operator’s seat.
•
Do not alter attachment or replace parts on the attachment
with other brands. Other brands may not fit properly or
meet OEM specifications. They can weaken the integrity
and impair the safety, function, performance, and life of the
attachment. Replace parts only with genuine OEM parts.
1.
Clean off any dirt and grease that may have
accumulated on the Road Saw and moving parts.
Scrape compacted dirt from the cutting wheel and
then wash surface thoroughly with a garden hose.
2. Check picks and pick holders for wear and replace if
necessary. Check picks to make sure they rotate in
the pick holders.
3. Spray picks with a water based asphalt emulsifier to
break down asphalt emulsion and to promote pick
rotation. (Example: Zep’s part #AR6690).
4. Inspect Road Saw for parts out of adjustment, loose,
damaged, or worn. Make required adjustments.
Tighten all loose hardware. Replace damaged and
worn parts as needed.
5. Repaint parts where paint is worn or scratched to
prevent rust. Ask your Kubota dealer for touch-up
paint. Paint is available in aerosol can, quarts, and
gallon sizes. See chart below.
Touch-up Paint
Part No.
Part Description
821-070C
821-070CTU
821-070CQT
821-070CGL
Gloss black enamel spray can
Gloss black enamel bottle with brush
Gloss black enamel quart
Gloss black enamel gallon
32
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 4: Maintenance & Lubrication
Lubrication
Legend
Multi-purpose
spray lube
Multi-purpose
grease lube
Multi-purpose
oil lube
50
Hrs
Intervals in hours at which
lubrication is required
Lubrication Points
SW3010 Road Saws
72204
Weekly
Sideshift Bars
IMPORTANT: Do not apply grease to the sideshift
bar. Grease catches milling dust and causes the
sideshift mechanism to bind and wear quickly.
1- Lower Sideshift Bar
Type of Lubrication:
Graphite lube spray such as CRC 30094
Quantity: Clean and spray sideshift bars once a week.
72189
8
Hours
Sideshift Rod
2 - Zerks
Type of Lubrication:
EP Lithium NLGL No. 2 grade Grease
Quantity: Add grease until grease begins to emerge.
72194
Fill Plug
250 hrs
or
yearly
Planetary Gearbox
Motor
Planetary Gearbox
Type of Lubrication: EP90 or SAE75W90 Synthetic Gear
lubricant
Oil Level Plug
Change oil at the first 100 hours of use. Thereafter,
change every 250 hours or yearly, whichever comes first.
Quantity: Fill until oil reaches oil level plug hole which is
rotated to be horizontal. Approximately 30 oz (1 L).
Refer to “SW3010 Gearbox Oil Change” on page 30.
Drain Plug
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
33
Table of Contents
Section 4: Maintenance & Lubrication
SW3018 Road Saws
72139
40 hrs
or
Weekly
Depth Cylinder Pivot Pins
2 - Zerks
Lubricate every 40 hours of use or weekly, whichever
comes first.
Type of Lubrication:
EP Lithium NLGL No. 2 Grade Grease
Quantity: Add grease until grease begins to emerge.
40 hrs
or
Weekly
72139
Depth Arm Pivot Pins
2- Zerks
Lubricate every 40 hours of use or weekly, whichever
comes first.
Type of Lubrication:
EP Lithium NLGL No. 2 Grade Grease
Quantity: Add grease until grease begins to emerge.
34
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 4: Maintenance & Lubrication
72190
Weekly
Sideshift Rods
IMPORTANT: Do not apply grease to the sideshift
rods. Grease catches milling dust and causes
the sideshift mechanism to bind and wear
quickly.
2 - Sideshift Bars (Upper and Lower)
Type of Lubrication:
Graphite lube spray such as CRC 30094
Quantity: Clean and spray sideshift bars once a week.
Typical Both Sides
72195
250 hrs
or
yearly
Fill Plug
Planetary Gearbox
Motor
Planetary Gearbox
Type of Lubrication: EP90 or SAE75W90 Synthetic Gear
lubricant
Oil Level Plug
Change oil at the first 100 hours of use. Thereafter,
change every 250 hours or yearly, whichever comes first.
Quantity: Fill until oil reaches oil level plug hole which is
rotated to be horizontal. Approximately 52 oz (1.5L).
Drain Plug
5/17/19
Refer to “SW3018 Gearbox Oil Change” on page 30.
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
35
Table of Contents
Section 5: Specifications & Capacities
Section 5: Specifications & Capacities
SW3010 & SW3018 Road Saws
Specifications & Capacities
Model Numbers
Cutting width
inches (cm)
Cutting depth
inches (cm)
SW3010-2.5
SW3010-4.5
SW3018-3.0
SW3018-4.5
SW3018-6.0
2 1/2 (6)
4 1/2 (11)
3 (8)
4 1/2 (11)
6 (15)
Number of picks
0 to 10 (0 to 25)
26
0 to 18(0 to 46)
34
30
Min. hydraulic flow gpm (Lpm)
30 (114)
Max. hydraulic flow gpm (Lpm)
42 (159)
48
Minimum pressure
psi (MPa)
2,500 (17.2)
Maximum pressure
psi (MPa)
5,000 (34,4)
Sideshift travel
inches (cm)
60
26 (66)
EP90 or SAE75W90 Synthetic Gear lubricant
Planetary gearbox oil type
Planetary gearbox oil capacity
Approximately 30 oz (1 L)
Approximate weight
1323
(600)
lbs
(kg)
1360
(617)
Approximately 52 oz (1.5 L)
1916
(869)
1970
(894)
2031
(921)
70 1/2"
(1.8 m)
49 1/2"
(1.26 m)
67 1/2"
(1.71 m)
67"
(1.7 m)
52"
(1.3 m)
43"
(1.1 m)
SW3010
36
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
SW3018
5/17/19
Table of Contents
Section 6: Features & Benefits
Section 6: Features & Benefits
SW3010 & SW3018 Road Saws
Features
Benefits
Removable carbide picks
Uses rocket fin technology that is built into the picks for longer life. Easy to replace.
Depth, and sideshift adjust
hydraulically
All functions are integrated into the multi-function grips of the SSV/SVL.
Depth indicator
Makes it easy to know depth of cut being made.
Case drain
Protects hydraulic motor and seals.
Polycarbonate door (optional)
Protects operator from thrown objects.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
37
Table of Contents
Section 7: Troubleshooting
Section 7: Troubleshooting
Troubleshooting Chart
Problem
Cutting wheel does not rotate.
Cutting wheel rotates
backward.
Motor oil seal is leaking.
Pick is wearing unevenly.
Cause
Auxiliary hydraulics switch for continuous
operation is not engaged.
Pick holders are wearing.
Engage auxiliary hydraulics switch for
continuous operation.
One or both of the hydraulic couplers are not Reconnect couplers to skid steer auxiliary
fully connected.
hydraulic outlets.
Male and female hydraulic couplers are
connected in reverse order.
Switch male and female couplers on
hydraulic hoses and then reconnect hoses to
the auxiliary hydraulic outlets.
Return line from motor has been pinched or
is collapsed.
Replace motor seal. Check motor return
hose for kinks.
Case drain line is not properly connected.
Connect case drain line to the hydraulic
motor and skid steer reservoir.
Pick is not rotating in the holder.
Spray picks daily with a water based asphalt
emulsifier to break down asphalt emulsion.
Example: Zep’s part # AR6690
Not inspecting picks frequently.
Inspect picks every 30 minutes of operation
for sign of pick rotation and wear. Replace
picks as needed. Refer to “Remove &
Install Picks” on page 29.
Picks are not kept clean.
Recommend adding a Water Spray Kit. This
kit can increase tooth life by 20 to 40% and
suppress milling dust.
Picks are cutting concrete most of the time.
Replace standard asphalt picks with concrete
picks.
Side loading on the cutting wheel during
steering corrections.
Make straight cuts. Keep steering corrections
to a minimum.
Not inspecting pick holders frequently.
Inspect pick holders every 30 minutes of
operation for wear. Replace pick holders as
needed. Refer to “Pick Holder Repair” on
page 29.
Pick is not rotating in the holder.
Spray picks daily with a water based asphalt
emulsifier to break down asphalt emulsion.
Example: Zep’s part # AR6690
Picks do not last long.
Edge picks are wearing faster
than the center picks.
Solution
Replace pick if pick is worn enough to
Pick is worn beyond its intended replacement indicate slight holder wear.
point.
Replace pick holder if worn excessively.
38
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 8: Torque Values Chart
Section 8: Torque Values Chart
Torque Values Chart for Common Bolt Sizes
Bolt Head Identification
Bolt Size
(inches)
1
in-tpi
1/4" - 20
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
Grade 2
N·m
7.4
8.5
15
17
27
31
43
49
66
75
95
105
2
ft-lb
5.6
6
11
13
20
22
32
36
49
55
70
79
Grade 5
3
N · m ft-lb
11
8
13
10
24
17
26
19
42
31
47
35
67
49
75
55
105
76
115
85
150
110
165
120
Bolt Head Identification
Grade 8
N · m ft-lb
16
12
18
14
33
25
37
27
59
44
67
49
95
70
105
78
145
105
165
120
210
155
235
170
Bolt Size
(Metric)
mm x pitch
M 5 X 0.8
M6X1
M 8 X 1.25
M8X1
M10 X 1.5
M10 X 0.75
M12 X 1.75
M12 X 1.5
M12 X 1
M14 X 2
M14 X 1.5
M16 X 2
4
5.8
8.8
10.9
Class 5.8
Class 8.8
Class 10.9
N·m
4
7
17
18
33
39
58
60
90
92
99
145
ft-lb
3
5
12
13
24
29
42
44
66
68
73
105
N·m
6
11
26
28
52
61
91
95
105
145
155
225
ft-lb
5
8
19
21
39
45
67
70
77
105
115
165
N·m
9
15
36
39
72
85
125
130
145
200
215
315
ft-lb
7
11
27
29
53
62
93
97
105
150
160
230
M16 X 1.5
155
115
240
180
335
245
5/8" - 11
130
97
205
150
285
210
5/8" - 18
150
110
230
170
325
240
M18 X 2.5
195
145
310
230
405
300
3/4" - 10
235
170
360
265
510
375
M18 X 1.5
220
165
350
260
485
355
3/4" - 16
260
190
405
295
570
420
M20 X 2.5
280
205
440
325
610
450
7/8" - 9
225
165
585
430
820
605
M20 X 1.5
310
230
650
480
900
665
7/8" - 14
250
185
640
475
905
670
M24 X 3
480
355
760
560
1050 780
1" - 8
340
250
875
645
1230 910
M24 X 2
525
390
830
610
1150
845
1" - 12
370
275
955
705
1350 995
M30 X 3.5
960
705
1510 1120
2100 1550
1-1/8" - 7
480
355
1080 795
1750 1290
M30 X 2
1060 785
1680 1240 2320 1710
1-1/8" - 12
540
395
1210 890
1960 1440
M36 X 3.5
1730 1270 2650 1950 3660 2700
1-1/4" - 7
680
500
1520 1120 2460 1820
M36 X 2
1880 1380 2960 2190 4100 3220
1 in-tpi = nominal thread diameter in inches-threads per inch
1-1/4" - 12
750
555
1680 1240 2730 2010
2 N· m = newton-meters
1-3/8" - 6
890
655
1990 1470 3230 2380
3 ft-lb= foot pounds
1-3/8" - 12
1010
745
2270 1670 3680 2710
4 mm x pitch = nominal thread diameter in millimeters x thread
1-1/2" - 6
1180
870
2640 1950 4290 3160
pitch
1-1/2" - 12
1330 980
2970 2190 4820 3560
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
Additional Torque Values
SW3018 Wheel Bolts 5/8"-11 x 1.5"
5/17/19
220-250 ft-lbs (298-239 Nm)
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
39
Table of Contents
Section 9: Warranty & Legal Disclaimer
Section 9: Warranty & Legal Disclaimer
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit: One year Parts and Labor
Hydraulic Motor: Two years Parts and Labor
Hydraulic Cylinder: One year Parts and Labor;
Hoses and seals are considered wear items.
Cutting Wheel, Picks, Pick Holders, and Bases: Considered wear items
This Warranty is limited to the repair or replacement of any defective part by
Land Pride and the installation by the dealer of any such replacement part, and
does not cover common wear items such as blades, belts, tines, etc. Land Pride
reserves the right to inspect any equipment or parts which are claimed to have
been defective in material or workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points and driveline shafts.
Claims under this Warranty should be made to the dealer which originally sold
the product and all warranty adjustments must be made through an authorized
Kubota dealer. Kubota reserves the right to make changes in materials or design
of the product at any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in this
written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days from
the date of original purchase. Registration is done by your dealer.
IMPORTANT: The Online Warranty Registration should be completed by the dealer at the time of
purchase. This information is necessary to provide you with quality customer service.
Model Number ____________________ Serial Number ____________________
40
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
5/17/19
Table of Contents
Section 9: Warranty & Legal Disclaimer
Legal Disclaimer
Kubota Corporation notes that specifications and technical information are subject to change without notice and Kubota
does not represent or warrant that the information in this publication is completely accurate or current; however, Kubota
used reasonable efforts to set forth and include accurate and up to date information in this publication. Kubota disclaims
all representations and warranties, whether express or implied, including, but not limited to, warranties of merchantability
and fitness for a particular purpose and Kubota shall not be liable for any damages, whether compensatory, direct,
indirect, incidental, special, or consequential, arising out of or in connection with the use of this publication, or in the
information therein.
The Product(s) described in this Publication are designed and manufactured only for the country in which they are
initially wholesaled by Kubota. Kubota does not provide parts, warranty or service for any Product which is re-sold or
retailed in any country other than the country for which the Product(s) were designed or manufactured.
5/17/19
AP-SW3010 & AP-SW3018 Road Saw 350-386MK
41
KUBOTA TRACTOR CORPORATION
1000 Kubota Drive, Grapevine, TX 76051
Telephone: (817) 756-1171
Western Division:
Telephone:
Central Division:
Telephone:
Northern Division:
Telephone:
Southeast Division:
Telephone:
1175 S. Guild Ave., Lodi, CA 95240
(209) 334-9910
14855 FAA Blvd., Fort Worth, TX 76155
(817) 571-0900
6300 at One Kubota Way, Groveport, OH 43125
(614) 835-1100
1025 Northbrook Parkway, Suwanee, GA 30024
(770) 995-8855
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement