Land Pride PFL12 Series Operator Manual

Land Pride PFL12 Series Operator Manual
Table of Contents
Pallet Fork
PFL1242
72040
319-211M
Operator’s Manual
!
Read the Operator’s Manual entirely. When you see this symbol,
the subsequent instructions and warnings are serious - follow
without exception. Your life and the lives of others depend on it!
Cover photo may show optional equipment not supplied
with standard unit.
For an Operator’s Manual and Decal Kit in French
Language, please see your Land Pride dealer.
Printed 4/17/19
Machine Identification
Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new
manual.
If you, or the dealer, have added Options not originally ordered with the machine, or removed Options that were
originally ordered, the weights and measurements are no longer accurate for your machine. Update the record by
adding the machine weight and measurements provided in the Specifications & Capacities Section of this manual with
the Option(s) weight and measurements.
Model Number
Serial Number
Machine Height
Machine Length
Machine Width
Machine Weight
Delivery Date
First Operation
Accessories
Dealer Contact Information
Name:
Street:
City/State:
Telephone:
Email:
!
California Proposition 65
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
PFL1242 Pallet Fork 319-211M
4/17/19
Table of Contents
Table of Contents
Important Safety Information . . . . . . . . . . . . . 1
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol . . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . .
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . .
Further Assistance . . . . . . . . . . . . . . . . . . . . . . . .
8
8
8
8
8
8
8
Section 1: Assembly & Set-Up . . . . . . . . . . . . 9
Fork Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Tractor Shutdown Procedure . . . . . . . . . . . . . . . . 10
Tractor Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 2: Adjustments . . . . . . . . . . . . . . . . . 11
Fork Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Section 3: Operating Procedures . . . . . . . . . 12
Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . .
Operating Safety . . . . . . . . . . . . . . . . . . . . . . . . . .
Transport Safety . . . . . . . . . . . . . . . . . . . . . . . . . .
Pallet Fork Operation . . . . . . . . . . . . . . . . . . . . . .
Picking up a Load . . . . . . . . . . . . . . . . . . . . . . .
Traveling with a Load . . . . . . . . . . . . . . . . . . . . .
Placing a Load . . . . . . . . . . . . . . . . . . . . . . . . . .
Unhooking the Pallet Fork . . . . . . . . . . . . . . . . . . .
General Operating Instructions . . . . . . . . . . . . . . .
12
12
13
13
13
14
14
14
15
Section 4: Maintenance & Lubrication . . . . . 16
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Long-Term Storage . . . . . . . . . . . . . . . . . . . . . . . .
Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . .
Pallet Fork Contact Points . . . . . . . . . . . . . . . . .
16
16
17
17
Section 5: Specifications & Capacities . . . .
Section 6: Features & Benefits . . . . . . . . . . .
Section 7: Troubleshooting . . . . . . . . . . . . . .
Section 8: Torque Values Chart . . . . . . . . . .
Section 9: Warranty . . . . . . . . . . . . . . . . . . . .
19
20
21
22
23
© Copyright 2019 All rights Reserved
Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.
Land Pride is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
4/17/19
Table of Contents
Table of Contents Continued
See previous page for Table of Contents.
Parts Manual QR Locator
Dealer QR Locator
The QR (Quick Reference) code on the
cover and to the left will take you to the
Parts Manual for this equipment.
Download the appropriate App on your
smart phone, open the App, point your
phone on the QR code and take a picture.
The QR code on the left will
link you to available dealers
for Land Pride products.
Refer to Parts Manual QR
Locator on this page for
detailed instructions.
4/17/19

Important Safety Information
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Safety at All Times
Careful operation is your best
assurance against an accident.
All operators, no matter how much
experience they may have, should
carefully read this manual and
other related manuals, or have the
manuals read to them, before
operating the power machine and
this attachment.
 Thoroughly read and understand
the “Safety Label” section. Read
all instructions noted on them.
 Do not operate the equipment
while under the influence of drugs
or alcohol as they impair the ability
to safely and properly operate the
equipment.
 The operator should be familiar
with all functions of the tractor and
attachment and be able to handle
emergencies quickly.
 Make sure all guards and shields
appropriate for the operation are in
place and secured before
operating attachment.
 Keep all bystanders away from
equipment and work area.
 Start tractor from the driver’s seat
with hydraulic controls in neutral.
 Operate tractor and controls from
the driver’s seat only.
 Never dismount from a moving
tractor or leave tractor unattended
with engine running.
 Do not allow anyone to stand
between tractor and attachment
while hooking-up.
 Keep hands, feet, and clothing
away from power-driven parts.
 While transporting and operating
equipment, watch out for objects
overhead and along side such as
fences, trees, buildings, wires, etc.
 Store attachment in an area where
children normally do not play.
When needed, secure attachment
against falling with support blocks.
4/17/19
!
Look for the Safety Alert Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention are
dependent upon the awareness, concern, prudence, and
proper training of personnel involved in the operation,
transport, maintenance, and storage of equipment.
Be Aware of
Signal Words
A signal word designates a degree or
level of hazard seriousness. The
signal words are:
! DANGER
Indicates a hazardous situation that, if
not avoided, will result in death or
serious injury.
Safety Precautions for
Children
Tragedy can occur if the operator
is not alert to the presence of
children. Children generally are
attracted to attachments and their
work.
 Never assume children will remain
where you last saw them.
 Keep children out of the work area
and under the watchful eye of a
responsible adult.
 Be alert and shut the attachment
and tractor down if children enter
the work area.
 Never carry children on the tractor
or attachment. There is not a safe
place for them to ride. They may
fall off and be run over or interfere
with the control of the power
machine.
 Never allow children to operate the
power machine, even under adult
supervision.
 Never allow children to play on the
power machine or attachment.
 Use extra caution when backing
up. Before the tractor starts to
move, look down and behind to
make sure the area is clear.
! WARNING
Indicates a hazardous situation that, if
not avoided, could result in death or
serious injury.
! CAUTION
Indicates a hazardous situation that, if
not avoided, may result in minor or
moderate injury.
Tractor Shutdown & Storage
 If engaged, disengage power
take-off.
 Park on solid, level ground and
lower attachment to ground or
onto support blocks.
 Put tractor in park or set park
brake, turn off engine, and remove
switch key to prevent unauthorized
starting.
 Relieve all hydraulic pressure to
auxiliary hydraulic lines.
 Wait for all components to stop
before leaving operator’s seat.
 Use steps, grab-handles and
anti-slip surfaces when stepping
on and off the tractor.
 Detach and store attachment in an
area where children normally do
not play. Secure attachment using
blocks and supports.
OFF
R EM O
VE
1
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
2
Use A Safety Chain
Transport Safely
 A safety chain will help control
drawn machinery should it
separate from the tractor drawbar.
 Use a chain with the strength
rating equal to or greater than the
gross weight of the towed
implement.
 Attach the chain to the tractor
drawbar support or other specified
anchor location. Allow only
enough slack in the chain to
permit turning.
 Always hitch the implement to the
machine towing it. Do not use the
safety chain tow the implement.
 Comply with federal, state, and
local laws.
 Use towing vehicle and trailer of
adequate size and capacity. Secure
equipment towed on a trailer with
tie downs and chains.
 Sudden braking can cause a towed
trailer to swerve and upset. Reduce
speed if towed trailer is not
equipped with brakes.
 Avoid contact with any overhead
utility lines or electrically charged
conductors.
 Always drive with load on end of
loader arms low to the ground.
 Always drive straight up and down
steep inclines with heavy end of a
tractor with loader attachment on
the “uphill” side.
Tire Safety
Practice Safe Maintenance
 Tire changing can be dangerous
and must be performed by
trained personnel using the
correct tools and equipment.
 Always maintain correct tire
pressure. Do not inflate tires
above recommended pressures
shown in the Operator’s Manual.
 When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
 Securely support the implement
when changing a wheel.
 When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
 Make sure wheel bolts have been
tightened to the specified torque.
 Understand procedure before doing
work. Refer to the Operator’s Manual
for additional information.
 Work on a level surface in a clean
dry area that is well-lit.
 Lower attachment to the ground and
follow all shutdown procedures
before leaving the operator’s seat to
perform maintenance.
 Do not work under any hydraulic
supported equipment. It can settle,
suddenly leak down, or be lowered
accidentally. If it is necessary to work
under the equipment, securely
support it with stands or suitable
blocking beforehand.
 Use properly grounded electrical
outlets and tools.
 Use correct tools and equipment for
the job that are in good condition.
 Allow equipment to cool before
working on it.
 Engage park brake when stopped
on an incline.
 Maximum transport speed for an
attached equipment is 20 mph. DO
NOT EXCEED. Never travel at a
speed which does not allow
adequate control of steering and
stopping. Some rough terrains
require a slower speed.
 As a guideline, use the following
maximum speed weight ratios for
attached equipment:
20 mph when weight of attached
equipment is less than or equal
to the weight of machine towing
the equipment.
10 mph when weight of attached
equipment exceeds weight of
machine towing equipment but
not more than double the weight.
 IMPORTANT: Do not tow a load
that is more than double the weight
of the vehicle towing the load.
 Disconnect battery ground cable (-)
before servicing or adjusting
electrical systems or before welding
on equipment.
 Inspect all parts. Make certain parts
are in good condition & installed
properly.
 Replace parts on this attachment
with genuine Land Pride parts only.
Do not alter this attachment in a way
which will adversely affect its
performance.
 Do not grease or oil attachment
while it is in operation.
 Remove buildup of grease, oil, or
debris.
 Always make sure any material and
waste products from the repair and
maintenance of the attachment are
properly collected and disposed.
 Remove all tools and unused parts
before operation.
4/17/19
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Prepare for Emergencies
 Be prepared if a fire starts.
 Keep a first aid kit and fire
extinguisher handy.
 Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
Wear Personal Protective
Equipment (PPE)
Avoid High
Pressure Fluids Hazard
 Wear protective clothing and
equipment appropriate for the job
such as safety shoes, safety
glasses, hard hat, and ear plugs.
 Clothing should fit snug without
fringes and pull strings to avoid
entanglement with moving parts.
 Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
 Operating equipment safely
requires the operator’s full
attention. Avoid wearing
headphones while operating
equipment.
 Escaping fluid under pressure can
penetrate the skin causing serious
injury.
 Relieve all residual pressure
before disconnecting hydraulic
lines or performing work on the
hydraulic system.
 Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
 Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
 Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
 DO NOT DELAY. If an accident
occurs, see a doctor familiar with
this type of injury immediately. Any
fluid injected into the skin or eyes
must be treated within
a few hours or
gangrene may
result.
Use Seat Belt and ROPS
Keep Riders Off
Machinery
911
Use Safety
Lights and Devices
 Slow moving tractors, and
self-propelled equipment can
create a hazard when driven on
public roads. They are difficult to
see, especially at night. Use the
Slow Moving Vehicle (SMV) sign
when on public roads.
 Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
4/17/19
 Land Pride recommends the use
of a CAB or roll-over-protectivestructures (ROPS) and seat belt
in almost all power machines.
Combination of a CAB or ROPS
and seat belt will reduce the risk
of serious injury or death if the
power machine should be upset.
 If ROPS is in the locked-up
position, fasten seat belt snugly
and securely to help protect
against serious injury or death
from falling and machine overturn.
 Never carry riders on tractor or
implement.
 Riders obstruct operator’s view
and interfere with the control of
the power machine.
 Riders can be struck by objects or
thrown from the equipment.
 Never use tractor or implement to
lift or transport riders.
3
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Avoid crystalline Silica
(quartz) Dust
Because crystalline silica is a basic
component of sand and granite,
many activities at construction sites
produce dust containing crystalline
silica. Trenching, sawing, and boring
of material containing crystalline
silica can produce dust containing
crystalline silica particles. This dust
can cause serious injury to the
lungs (silicosis).
There are guidelines which should
be followed if crystalline silica
(quartz) is present in the dust.
4
 Be aware of and follow OSHA
(or other local, State, or Federal)
guidelines for exposure to airborne
crystalline silica.
 Know the work operations where
exposure to crystalline silica may
occur.
 Participate in air monitoring or
training programs offered by the
employer.
 Be aware of and use optional
equipment controls such as water
sprays, local exhaust ventilation,
and enclosed cabs with positive
pressure air conditioning if the
machine has such equipment.
Otherwise respirators shall be worn.
 Where respirators are required, wear
a respirator approved for protection
against crystalline silica containing
dust. Do not alter respirator in any
way. Workers who use tight-fitting
respirators can not have beards/
mustaches which interfere with the
respirator seal to the face.
Handle
Chemicals Properly
Dig Safe - Avoid
Underground Utilities
 Protective clothing should be
worn.
 Handle all chemicals with care.
 Follow instructions on container
label.
 Agricultural chemicals can be
dangerous. Improper use can
seriously injure persons, animals,
plants, soil, and property.
 Inhaling smoke from any type of
chemical fire is a serious health
hazard.
 Store or dispose of unused
chemicals as specified by the
chemical manufacturer.
 USA: Call 811
CAN: digsafecanada.ca
Always contact your local utility
companies (electrical, telephone,
gas, water, sewer, and others)
before digging so that they may
mark the location of any
underground services in the area.
 Be sure to ask how close you can
work to the marks they positioned.
 If possible, change into disposable
or washable work clothes at the
work site; shower and change into
clean clothing before leaving the
work site.
 Do not eat, drink, use tobacco
products, or apply cosmetics in
areas where there is dust containing
crystalline silica.
 Store food, drink, and personal
belongings away from the work
area.
 Wash hands and face before eating,
drinking, smoking, or applying
cosmetics after leaving the exposure
area.
4/17/19
Important Safety Information
This page left blank intentionally.
4/17/19
5
Table of Contents
Important Safety Information
Important Safety Information
Safety Labels
Your Pallet Fork comes equipped with all safety labels in place.
They were designed to help you safely operate your implement.
Read and follow their directions.
1. Keep all safety labels clean and legible.
2. Refer to this section for proper label placement. Replace
all damaged or missing labels. Order new labels from your
nearest Land Pride dealer. To find your nearest dealer,
visit our dealer locator at www.landpride.com.
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
4.
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
Refer to this section for proper label placement.
To install new labels:
a. Clean surface area where label is to be placed.
b. Spray soapy water onto the cleaned area.
c. Peel backing from label and press label firmly onto the
surface.
d. Squeeze out air bubbles with edge of a credit card or
with a similar type of straight edge.
72042
818-798C
Warning: Pinch Point Hazard
72042
858-971C
Warning: Lift Capacity & Safe Operation
6
PFL1242 Pallet Fork 319-211M
4/17/19
Table of Contents
Important Safety Information
72042
838-293C
Warning: Read Manual
72043
858-995C
1200 lbs. Lift Capacity
4/17/19
PFL1242 Pallet Fork 319-211M
7
Table of Contents
Introduction
Introduction
Land Pride welcomes you to the growing family of new
product owners. This Pallet Fork has been designed with
care and built by skilled workers using quality materials.
Proper assembly, maintenance, and safe operating
practices will help you get years of satisfactory use from
this product.
Application
The Land Pride PFL1242 Pallet Fork has uses and
applications in farming, ranching, nurseries, campuses,
theme parks, warehouses, lumber yards, and large or
small retail outlets. This pallet fork will quickly and
conveniently turn your compact and/or sub-compact
tractor loader, equipped with loader arms and universal
quick-attach hitch plate, into a forklift to expand your
material handling capability.
customer service or repair parts are required. Your Land
Pride dealer has trained personnel, repair parts, and
equipment needed to service the implement.
Serial Number
For quick reference and prompt service, record model
and serial number on the inside cover page and again on
the warranty page. Always provide model number and
serial number when ordering parts and in all
correspondences with your Land Pride dealer. For
location of your serial number plate, see Figure 1.
72042
The first two digits in the model number indicate weight
class (PFL1242 = 1,200 lbs) and the last two digits give
fork length (PFL1242 = 42").
For additional information and performance enhancing
options, see “Specifications & Capacities” on page 19
and “Features & Benefits” on page 20.
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
72042
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual, contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge, from our website at
www.landpride.com
Terminology
Serial Number Plate Location
Figure 1
Further Assistance
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Your dealer wants you to be satisfied with your new pallet
fork. If for any reason you do not understand any part of
this manual or are not satisfied with the service received,
the following actions are suggested:
Definitions
1.
IMPORTANT: A special point of information related
to the following topic. Land Pride’s intention is this
information must be read & noted before continuing.
NOTE: A special point of information that the
operator should be aware of before continuing.
Owner Assistance
The dealer should complete the Online Warranty
Registration at the time of purchase. This information is
necessary to provide you with quality customer service.
The parts on your Pallet Fork have been specially
designed by Land Pride and should only be replaced with
genuine Land Pride parts. Contact a Land Pride dealer if
8
PFL1242 Pallet Fork 319-211M
Discuss any problems you have with your attachment
with your dealership service personnel so they can
address the problem.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
question/problem, and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
[email protected]
4/17/19
Table of Contents
Section 1: Assembly & Set-Up
Section 1: Assembly & Set-Up
72047
Pin Notches
Notched Opening
Fork Installation
Figure 1-1
Fork Installation
Refer to Figure 1-1:
! CAUTION
To avoid minor or moderate injury:
A pinching hazard exists when installing forks. Do not place
hands or fingers between carrying bars and forks.
1.
5. Repeat steps 1-4 for the second fork, but slide the
second fork to the left.
NOTE: Never place 2 forks on the same side of
notch opening. Always have them equal distance
from the center of the frame.
Raise the fork locking pin (#1) straight up.
2. Center upper end of fork (#2) on upper carrying
bar (#3). Make sure retaining hook (A) is caught
behind upper carrying bar (#3) and retaining
hook (B) fits in notched opening in lower carrying
bar (#4).
3. Slide fork to the right by pushing on the fork near
carrying bars (#3 & #4) until locking pin (#1) is
positioned over one of the pin notches.
4. Lower locking pin handle (#1) to seat pin in the
selected notch. Make sure locking pin is seated and
retaining hooks “A” & “B” are secured behind the
carrying bars.
4/17/19
PFL1242 Pallet Fork 319-211M
9
Table of Contents
Section 1: Assembly & Set-Up
Tractor Shutdown Procedure
72043
The following are basic tractor shutdown procedures.
Follow these procedures and any additional shutdown
procedures provided in your tractor Operator’s Manual
before leaving the operator’s seat.
1.
Reduce engine speed and shut-off all power to the
attachment.
2. Park tractor and attachment on solid, level ground.
3. Lower attachment until it is flat on the ground or on
non-concrete support blocks.
Top
Angle Bar
4. Put tractor in park or set park brake, turn off engine,
and remove switch key to prevent unauthorized
starting.
Pallet Fork
Hitch Plate
5. Relieve all hydraulic pressure to auxiliary hydraulic
lines.
6. Wait for all components to come to a complete stop
before leaving the operator’s seat.
7.
Bottom Slots
Use steps, grab-handles and anti-slip surfaces when
stepping on and off the tractor.
Pallet Fork With Universal Quick Attach Hitch Plate
Figure 1-2
Tractor Hook-Up
Refer to Figure 1-2:
! DANGER
To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking the
attachment. Do not allow anyone to stand between attachment
and power machine while approaching or backing away from
the attachment. Do not operate lift and/or tilt controls while
someone is near the power machine and/or attachment.
! WARNING
To avoid serious injury or death:
• Lightweight power machines may need weight added to the
rear to maintain steering control and prevent forward
tipping or side tipping caused by a heavy front load. Consult
your power machine Operator’s Manual to determine
proper weight requirements and maximum weight
limitations.
•
Check hitch fit-up frequently. An improper fit-up can cause
the attachment to come loose from the loader hitch plate
and fall.
•
Always shut power machine down following the “Shutdown
Procedure” provided in this manual before leaving the
operator’s seat.
10
PFL1242 Pallet Fork 319-211M
1.
If needed, pull locking handles up on loader hitch
until locking pins are fully raised.
2. Carefully drive up to the pallet fork making sure
loader hitch is parallel with the pallet fork hitch plate.
3. Tilt top of loader hitch slightly forward.
4. Place top of loader hitch under the top angled bars
on the pallet fork hitch plate.
5. Slowly lift loader hitch up until hitch and top angle
bars on the pallet fork have come together.
6. Tilt top of loader hitch back to align bottom slots in the
pallet fork hitch plate with locking pins on the loader
hitch.
7.
Continue tilting pallet fork back until forks are slightly
higher at the front than at the back. Lower loader
arms until forks are slightly above ground surface.
8. Shut tractor down properly. See “Tractor Shutdown
Procedure”.
9. Push locking handles on loader hitch down until
locking pins fully extend through bottom slots in pallet
fork hitch plate. Make sure locking handles are
locked into position to keep pins from backing out.
4/17/19
Table of Contents
Section 2: Adjustments
Section 2: Adjustments
Fork Adjustment
72042
Upper Carrying Bar
Refer to Figure 2-1:
! WARNING
Lower Carrying Bar
To avoid serious injury or death:
Always adjust pallet forks an equal distance away from the
center and as far apart as the pallet will allow. This will
optimize load stability, protect against load shifting, and make
handling the load safer.
! CAUTION
To avoid minor or moderate injury:
A pinching hazard exists when repositioning forks. Do not
place hands or fingers between carrying bars and forks.
1A
2A
Retaining
Hooks
2
NOTE: Forks will adjust easier if glide surfaces are
kept lubricated. See “Pallet Fork Contact Points”
on page 17 for lubricating instructions.
1.
Locate tractor and pallet fork on a flat, level surface.
Place transmission in park or set park brake.
Notch locations
1
2. Tilt Pallet Fork until front of forks are slightly lower at
the front than at the back. Lower loader arms until
forks are slightly above ground surface.
3. Shut tractor down properly. See “Tractor Shutdown
Procedure” on page 10.
Fork Adjustment
Figure 2-1
4. Pull the fork locking pin handle (#1A) straight up.
5. Slide pallet fork (#1) to the optimized load carrying
width by pushing or pulling on the fork near the
carrying bars. Be sure to position locking pin (#1A)
directly over one of the five notches in the upper
carrying bar.
6. Lower locking pin (#1A) to seat locking pin in the
selected notch.
• Check locking pin to be sure it has seated.
• Check retaining hooks to be sure they are secured
7.
behind upper and lower carrying bars.
Repeat steps 1 to 6 for fork (#2). Make sure both
forks are an equal number of notches away from the
middle of the upper carrying bar.
4/17/19
PFL1242 Pallet Fork 319-211M
11
Table of Contents
Section 3: Operating Procedures
Section 3: Operating Procedures
Operating Checklist
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the pallet fork. Therefore, it is absolutely
essential that no one operates this unit unless they are
age 16 or older and have read, fully understood, and are
totally familiar with the Operator’s Manual. Make sure the
operator has paid particular attention to:
•
Always adjust forks so that they are evenly spaced as far
apart as the load will allow and centered on the frame. Keep
load centered on the forks, even when stopped. This will
optimize load stability and protect against load shifting.
•
Never lift a load with one fork or more than two forks.
Using one fork will cause the load to be unbalanced. Using
more than two forks will not increase the lift capacity and
can make the job unsafe.
•
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment
supported by concrete blocks or hydraulics. Concrete can
break, hydraulic lines can burst, and/or hydraulic controls
can be actuated even when power to hydraulics is off.
•
Keep attachment, loader arms, and/or load away from
overhead electrical power lines. Place an orange warning
sign under overhead lines indicating type of danger above.
•
Always use ROPS & seatbelt warning.
Perform the following inspections before using your
Pallet Forks.
Operating Checklist

Check
Read and follow all safety rules carefully.
Refer to “Important Safety Information” and
Safety Alert Symbols throughout this manual.
Read and follow assembly instructions.
Refer to “Section 1: Assembly & Set-Up”.
Read and follow all operating procedures
Refer to “Section 3: Operating Procedures”.
Read and follow all maintenance instructions.
Refer to “Section 4: Maintenance & Lubrication”
Check Pallet Fork initially and periodically for
loose forks, hitch plate, bolts, and pins.
Refer to “Section 8: Torque Values Chart”.
Page
1
9
12
16
22
Operating Safety
! WARNING
To avoid serious injury or death:
• Allow only persons to operate this attachment who have
fully read and comprehended this manual, who are properly
trained to operate the attachment safely, and who are age 16
or older. Serious injury or death can result from the failure
to read, understand, and follow instructions provided in this
manual.
•
Never carry riders on the attachment or power machine.
Riders can obstruct the operator’s view, interfere with
control of the equipment, be pinched by moving
components, become entangled in rotating components, be
struck by objects, be thrown or fall from the equipment, etc.
•
Hydraulic fluid under high pressure can penetrate the skin
and/or eyes causing a serious injury. Wear protective gloves
and safety glasses or goggles when working with hydraulic
systems. Use a piece of cardboard or wood rather than
hands when searching for leaks. A doctor familiar with this
type of injury must treat the injury within a few hours or
gangrene may result. DO NOT DELAY.
! DANGER
To avoid serious injury or death:
• A crushing hazard always exists around equipment
handling palletized loads. Objects on pallet can shift and
fall resulting in death or serious injury.
•
Keep bystanders, pets, and livestock away from your work
area. Never allow anyone to go near or under the
attachment or its load. The attachment and/or load can fall.
•
Do not drive up to anyone or an animal in front of a fixed
object such as a wall or bench. Never assume that the power
machine will stop in time.
•
Use a “spotter” when it is hard to see in the direction you
are traveling and when placing a load that obstructs your
vision. A person or animal could be nearby in a blind spot.
Do not abuse equipment. Incorrect use of the attachment
can damage equipment structurally and cause serious
injury or death.
•
Check pallet fork frequently to make sure it is properly
attached to the loader hitch, forks are secured to the upper
and lower carrying bars, and fork locking pins are seated in
their notches.
•
Consult your power machine’s manual for operating
capacity, lifting capacity, and operating specifications.
Exceeding rated capacities and specifications can result in
a roll-over or other serious hazard.
•
Always know the weight of the load being lifted. Maximum
lift capacity should never exceed rated lift capacity of the
pallet fork. Also, it should never exceed 83% of the tractor
rated lift capacity. Use the smaller number of the two lift
capacities to determine maximum lift capacity.
•
•
Never lift objects without pallets and make sure all objects
are secured before lifting them. Use extreme care when
securing round objects to make sure they can’t roll off.
•
Lift only objects that have a stable base resting on the
pallet. Uneven, irregular, or round bases can easily tip off
or roll off the pallet.
•
Do not lift loads that exceed the load guard height and do
not lift loads that have objects smaller than the openings in
the load guard.
•
Keep load slightly tilted back to secure its weight against
the vertical face of the forks. Rotating front of forks too high
can cause the load to shift and fall onto the operator or
others. Rotating front of forks level or lower can cause the
load to fall forward.
12
PFL1242 Pallet Fork 319-211M
4/17/19
Table of Contents
Section 3: Operating Procedures
•
Do not travel across inclines where equipment could slip or
roll-over. Consult your power machine Operator’s Manual
for acceptable inclines they are capable of crossing.
•
Do not use forks for digging, pushing, pulling or prying
objects. Only use forks to lift palletized loads.
•
Do not use attachment to lift the front or back of the power
machine off the ground. Doing so can damage the
attachment, power machine, and/or cause serious injury or
death.
•
Do not chain or strap palletized loads to the loader arms,
loader hitch, pallet fork hitch plate or forks.
•
Do not use fork extensions. Fork extensions can damage
forks, pallet fork frame, loader hitch, and overload front of
machine resulting in loss of steering control and load.
•
The parts on your pallet fork have been specially designed
and should only be replaced with genuine Land Pride parts.
Altering the equipment can adversely affect its performance
and/or reliability.
•
•
When traveling on public roads, use LED lights, slow
moving vehicle sign, clean reflectors, and other adequate
devices to warn operators in other vehicles of your
presence. If implement blocks visibility of slow moving
vehicle sign, relocate sign so it is visible from the back at all
times. Always comply with all federal, state, and local laws.
•
When traveling on public roadways, travel in such a way
that faster moving vehicles may pass safely. Use accessory
lights, clean reflectors, and a slow moving vehicle sign that
is visible from the back to warn operators in other vehicles
of your presence. Always comply with all federal, state, and
local laws.
Pallet Fork Operation
Picking up a Load
1.
• Rated lift capacity of the pallet forks.
• 83% of the rated lift capacity of the tractor front
Always lower forks to ground level before dismounting from
the skid steer/tractor. Follow manufacturer’s
recommendations when dismounting and parking the
machine.
•
Always store attachment in a secure position so that it will
not fall over.
•
Always stack pallets in such a manner that they will not tip
or fall.
loader.
IMPORTANT: Do not attach chain intended for lifting
or securing loads to the pallet fork frame. Doing so
can cause damage to the frame.
IMPORTANT: Using 83% of the rated lift capacity
accounts for increased loader stresses caused by
the added extension of the pallet fork. It also ensures
that the front tires on your tractor are rated properly
for the job.
Transport Safety
! WARNING
To avoid serious injury or death:
• Follow all safety precautions when transporting a load. Not
using safe transporting methods can damage the equipment
and cause serious injury or death.
•
•
•
•
Lightweight power machines may need weight added to the
rear to maintain steering control and prevent forward
tipping or side tipping caused by a heavy front load. Consult
your power machine Operator’s Manual to determine
proper weight requirements and maximum weight
limitations.
Always transport loads as close to the ground as possible
without hitting objects. A load carried high could shift
causing the load to fall, tipping of the machine, and/or loss
of control.
Transporting loads across inclines, over ramps, on bumpy,
soft, or slippery surfaces reduces machine stability and lift
capacity. Transporting and lifting loads under these
conditions is extremely dangerous. Follow all transport
instructions in your power machine Operator’s Manual.
Make sure the load does not exceed the smaller of
two lift capacities:
IMPORTANT: On heavy loads, the center of gravity
should not be positioned farther than 24" away from
the vertical face of the forks. Picking up heavy loads
positioned farther away can damage the unit and
void its warranty.
2. Center forks under the pallet to evenly distribute the
weight.
3. Make sure the load is balanced and secure.
4. Check for overhead obstructions.
5. Stop completely before positioning forks at the
correct height.
6. Drive into the load as far as possible.
7.
Lift load just off the ground and tilt it back slightly.
8. Back out slowly to clear racks or other obstacles.
9. Position load at a safe traveling height before
moving. Two to four inches above the floor is
recommended traveling height.
Always transport over ramps and inclines with the heavy
end of the power machine on the “uphill” side. This may
require one to drive up and back down inclines.
4/17/19
PFL1242 Pallet Fork 319-211M
13
Table of Contents
Section 3: Operating Procedures
Traveling with a Load
1.
Pedestrians always have the right-of-way.
2. Keep load tilted back slightly.
3. Unhook pallet fork as follows:
a. Pull lock handles up to remove pins from bottom
slots in hitch plate.
3. Keep forks low, two to four inches above the floor,
when possible.
b. Return to tractor, restart and tilt top of hitch plate
slightly forward toward the pallet fork.
4. Continually scan all sides for pedestrians or other
traffic.
c. Slowly lower the pallet fork onto the ground until
its top angle bar and loader hitch have separated.
5. If load is large and blocks your view, travel in reverse.
d. Back tractor away slowly from the pallet fork while
making sure the loader hitch does not interfere
with the pallet fork.
6. Always drive at a safe speed and slow down when
going around corners. Avoid sudden braking.
7.
72043
Leave enough clearance when turning to keep pallet
forks and load from contacting obstacles such as
storage racks, buildings, trees, or fences.
8. When traveling over a ramp or incline, keep load on
the “uphill” side of the tractor.
9. When possible, travel straight up and down grades,
ramps, and inclines. Avoid making turns on grades,
ramps, and inclines.
10. Raise or lower load only when stopped, never while
traveling.
Top
Angle Bar
11. Slow down when traveling over rough or hilly terrain.
12. Do not transport loads on public roadways.
13. When traveling on public roadways, transport in such
a way that faster moving vehicles may pass you
safely.
14. Plan your route to avoid heavy traffic.
Placing a Load
1.
Bottom slots
Stop in front of desired location to place the load.
2. Slowly raise load to required height.
3. Move forward slowly with load raised until load is
positioned square and straight above its final
destination.
Pallet Fork With Loader Mounting Plate
Figure 3-1
4. Level load to position it for placement.
5. Lower load onto it final resting location.
6. Before backing, check all sides for pedestrians or
other traffic.
7.
Once load has settled, back up slowly.
8. Make sure forks clear pallet before turning or
changing fork height.
9. Lower forks before moving again.
Unhooking the Pallet Fork
Refer to Figure 3-1:
1. Park tractor with unit on a flat, level, solid surface and
lower pallet fork until slightly above the surface and
hitch angled with front of pallet forks slightly higher
than rear of pallet forks.
2. Without lowering the Pallet Fork, shut trator down
properly. See “Tractor Shutdown Procedure” on
page 10.
14
PFL1242 Pallet Fork 319-211M
4/17/19
Table of Contents
Section 3: Operating Procedures
General Operating Instructions
By now you should have familiarized yourself with the
Operator’s Manual for your Pallet Fork.
If you haven’t, please do so now. We cannot overstress
the importance of following the safety operating
procedures that are spelled out in this Manual.
Proceed by getting onto the tractor seat, fastening
seatbelt and starting tractor. It isn’t going to take you long
to learn how to use your new Land Pride Pallet Fork.
We recommend that you take a little time to practice
securely attaching and detaching your pallet fork to and
from your tractor universal quick-attach hitch. It is also
important to practice lifting, lowering, maneuvering, and
placing an empty pallet on a level site until you gain the
confidence and skill needed to have a good feel in what
you are doing.
As you quickly become more skilled and adept in using
your Pallet Fork, you will soon learn that it is always more
important to focus on the don’ts than it is to focus on the
dos. For example, don’t exceed the lift capacity of your
forks or tractor. Don’t lift your load too high creating an
unstable load and unsafe situation. Don’t tilt your load too
far backwards, setting up a situation that could cause
your load to roll or spill backwards onto you, the tractor,
and the operator’s platform. Don’t drive too fast for your
ground and load conditions. Don’t work on or around
slippery or sloped areas that could cause you to lose
control of the tractor. Don’t allow pedestrians, pets, or
livestock to approach the danger zone of your working
area. Don’t leave your tractor with forks or load raised off
of the ground.
If you just follow these few safety reminders, you will find
that you will quickly become very adept, handy, and
skillful at using your Land Pride pallet fork.
See “Specifications & Capacities” on page 19 and
“Features & Benefits” on page 20 of your Operator’s
Manual for additional information.
4/17/19
PFL1242 Pallet Fork 319-211M
15
Table of Contents
Section 4: Maintenance & Lubrication
Section 4: Maintenance & Lubrication
Maintenance
! DANGER
To avoid serious injury or death:
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment supported
by concrete blocks or hydraulics. Concrete can break,
hydraulic lines can burst, and/or hydraulic controls can be
actuated even when power to hydraulics is off.
! WARNING
To avoid serious injury or death:
• Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting implement
back into service.
•
Land Pride Touch-up Paint
Part No.
Part Description
821-070C
PAINT GP GLOSS BLACK SPRAY CAN
4. Replace all damaged or missing decals.
5. A coating of oil may also be applied to areas where
paint is worn off to minimize oxidation.
6. Store pallet fork inside a building and away from
human activity if possible. Inside storage will reduce
maintenance and make for a longer life.
7.
Follow all unhooking instructions on page 14 when
disconnecting a tractor from the Pallet Fork.
8. Do not allow children to play on or around the stored
pallet fork.
Do not alter implement or replace parts on the implement
with other brands. Other brands may not fit properly or
meet OEM (Original Equipment Manufacturer)
specifications. They can weaken the integrity and impair the
safety, function, performance, and life of the implement.
Replace parts only with genuine OEM parts.
Proper servicing and adjustments are key to the long life
of any implement. With careful inspection and routine
maintenance, you can avoid costly downtime and repair.
1.
After using your pallet fork for a few lifts, check forks
to make sure they are still secured and check pallet
fork to make sure it is still properly attached to the
loader hitch.
2. Check forks to make sure they are not damaged,
broken, or worn excessively. Repair or replace as
needed.
3. Always remove any material that has become
entangled in the forks before continuing to use them.
4. Replace any worn, damaged, or illegible safety
labels by obtaining new labels from your Land Pride
dealer.
Long-Term Storage
Clean, inspect, service, and make necessary repairs to
the attachment when storing it for long periods and at the
end of the season. This will help ensure the unit is ready
for field use the next time you hook-up to it.
1.
Remove any dirt and grease that may have
accumulated on the pallet fork. Scrape off compacted
dirt and then wash its surface thoroughly with a
garden hose.
2. Inspect pallet fork for loose, damaged, or worn parts
and adjust or replace when needed.
3. Repaint parts where paint is worn or scratched to
prevent rust. Ask your Land Pride dealer for aerosol
touch-up paint. Paint is also available in touch-up
bottles with brush, quarts, and gallon sizes by adding
TU, QT, or GL to the end of the aerosol part number.
16
PFL1242 Pallet Fork 319-211M
4/17/19
Table of Contents
Section 4: Maintenance & Lubrication
Lubrication Points
Lubrication
Legend
Multi-purpose
spray lube
Multi-purpose
grease lube
50
Hrs
Multi-purpose
oil lube
72042
Intervals in hours at which
lubrication is required
As
Required
Pallet Fork Contact Points
Top & face of upper carrying bar
Face of lower carrying bar
Type of Lubrication: Multi-purpose Grease
Quantity = As needed
4/17/19
PFL1242 Pallet Fork 319-211M
17
Table of Contents
Section 4: Maintenance & Lubrication
This page intentionally left blank.
18
PFL1242 Pallet Fork 319-211M
4/17/19
Table of Contents
Section 5: Specifications & Capacities
Section 5: Specifications & Capacities
PFL12 Series
Specifications & Capacities
PFL1242
Weight
lbs (kg)
220 (100)
Lift Capacity
lbs (kg)
1200 (544)
in (cm)
Lift capacity is based on load being 24 (61) from face of frame
(Cross bar). Load must be palletized and supported by two forks.
Frame Width
in (m)
45 1/2 (1.16)
Frame Height
in (cm)
32 (80.6)
Tine Thickness
in (cm)
1 1/4 (3.2)
Tine Width
in (cm)
3 (7.6)
Tine Length
in (m)
42 (1.07)
Class
l
Fork Positioning Lock
Spring Loaded
32"
(81.3 cm)
45 1/2" (1.16 m)
4/17/19
LOAD CAPACITY BASED
ON LOAD BEING 24" (61 cm)
FROM FACE OF FRAME
49" (1.24 m)
PFL1242 Pallet Fork 319-211M
19
Table of Contents
Section 6: Features & Benefits
Section 6: Features & Benefits
PFL12 Series
Features
Benefits
Universal Quick-Attach style hitch
plate
The Pallet Fork can be attached to a wide variety of machines.
Note: PFL12 series are offered with universal quick attach style hitch plate.
Tall rear guard
Keep loads from slipping backwards.
Attaches to power equipment easily
Uses universal quick attach style hitch plate for quick and easy attachment.
Easy adjustable forks
Forks slide easily on carrying bars from one position to another. Simply pull locking
handles up and slide forks to their new positions. Release locking handles to
secure forks in their new position.
20
PFL1242 Pallet Fork 319-211M
4/17/19
Table of Contents
Section 7: Troubleshooting
Section 7: Troubleshooting
Troubleshooting Chart
Problem
Cannot lift pallet
Forks are shifting sideways
on carrying bars
Forks are bending or breaking
Cause
Solution
Pallet load is too heavy.
Reduce load on pallet.
Insufficient power to lift load.
Switch to a tractor that is rated for more lift
capacity.
Locking pin handle is not engaged in
locking groove.
Position locking pins over locking grooves
on carrying bar and rotate locking handle
down to engage locking pin.
The load’s center of gravity is more than
24" away from vertical face of forks.
Reposition load on pallet so that center of
gravity is closer to the vertical faces.
Pallet load is too heavy.
Reduce load on pallet.
Prying objects out of the ground.
Never use forks to pry objects.
Load is not properly secured on pallet.
Secure load to pallet.
Load is not properly centered on pallet.
Center load on pallet.
Load is being carried too high.
Recommended carrying height is 2" to 4"
above the ground.
Forks are too close to each other.
Adjust forks an equal distance away from
the center and as far apart as the pallets
will allow.
Traveling with forks level or tilted down at
the front.
Rotate forks back so that the ends at the
front are slightly higher than at the back.
Traveling too fast.
Reduce speed to a safe non-bouncing
speed.
Traveling sideways to an incline.
Travel straight up and down inclines.
Traveling forward while going down an
incline with a slop in excess of 10 percent.
Back down steep inclines.
One fork is bent.
Replace bent fork.
Pallet fork hitch plate is not properly
attached to loader hitch.
Reattach pallet fork hitch plate to loader
hitch. Always make certain hitch is
properly attached before lifting a load.
Pallet load is shifting
4/17/19
PFL1242 Pallet Fork 319-211M
21
Table of Contents
Section 8: Torque Values Chart
Section 8: Torque Values Chart
Torque Values Chart For Common Bolt Size
Bolt Head Identification
Bolt Size
(inches)
1
in-tpi
1/4" - 20
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
Grade 2
2
N·m
7.4
8.5
15
17
27
31
43
49
66
75
95
105
Grade 5
3
ft-lb
5.6
6
11
13
20
22
32
36
49
55
70
79
N·m
11
13
24
26
42
47
67
75
105
115
150
165
ft-lb
8
10
17
19
31
35
49
55
76
85
110
120
Grade 8
N·m
16
18
33
37
59
67
95
105
145
165
210
235
5/8" - 11
130
97
205
150
285
5/8" - 18
150
110
230
170
325
3/4" - 10
235
170
360
265
510
3/4" - 16
260
190
405
295
570
7/8" - 9
225
165
585
430
820
7/8" - 14
250
185
640
475
905
1" - 8
340
250
875
645 1230
1" - 12
370
275
955
705 1350
1-1/8" - 7
480
355 1080
795 1750
1-1/8" - 12
540
395 1210
890 1960
1-1/4" - 7
680
500 1520
1120 2460
1-1/4" - 12
750
555 1680 1240 2730
1-3/8" - 6
890
655 1990 1470 3230
1-3/8" - 12
1010
745 2270 1670 3680
1-1/2" - 6
1180
870 2640 1950 4290
1-1/2" - 12
1330
980 2970 2190 4820
Torque tolerance + 0%, -15% of torquing values. Unless
22
PFL1242 Pallet Fork 319-211M
Bolt Head Identification
ft-lb
12
14
25
27
44
49
70
78
105
120
155
170
Bolt Size
(Metric)
mm x pitch
M 5 X 0.8
M6X1
M 8 X 1.25
M8X1
M10 X 1.5
M10 X 0.75
M12 X 1.75
M12 X 1.5
M12 X 1
M14 X 2
M14 X 1.5
M16 X 2
4
5.8
8.8
10.9
Class 5.8
Class 8.8
Class 10.9
N·m
4
7
17
18
33
39
58
60
90
92
99
145
ft-lb
3
5
12
13
24
29
42
44
66
68
73
105
N·m
6
11
26
28
52
61
91
95
105
145
155
225
ft-lb
5
8
19
21
39
45
67
70
77
105
115
165
N·m
9
15
36
39
72
85
125
130
145
200
215
315
ft-lb
7
11
27
29
53
62
93
97
105
150
160
230
155
115
240
180
335
245
210 M16 X 1.5
240 M18 X 2.5
195
145
310
230
405
300
375 M18 X 1.5
220
165
350
260
485
355
420 M20 X 2.5
280
205
440
325
610
450
605 M20 X 1.5
310
230
650
480
900
665
670 M24 X 3
480
355
760
560 1050
780
910 M24 X 2
525
390
830
610
1150
845
995 M30 X 3.5
960
705 1510
1120 2100 1550
1290 M30 X 2
1060
785 1680 1240 2320 1710
1440 M36 X 3.5
1730 1270 2650 1950 3660 2700
1820 M36 X 2
1880 1380 2960 2190 4100 3220
2010 1 in-tpi = nominal thread diameter in inches-threads per inch
2380 2 N· m = newton-meters
2710 3 ft-lb= foot pounds
3160 4 mm x pitch = nominal thread diameter in millimeters x thread
3560 pitch
otherwise specified use torque values listed above.
4/17/19
Table of Contents
Section 9: Warranty
Section 9: Warranty
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit: One year Parts and Labor
This Warranty is limited to the repair or replacement of any defective part by
Land Pride and the installation by the dealer of any such replacement part, and
does not cover common wear items. Land Pride reserves the right to inspect any
equipment or parts which are claimed to have been defective in material or
workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.
Claims under this Warranty should be made to the dealer which originally sold
the product and all warranty adjustments must be made through an authorized
Land Pride dealer. Land Pride reserves the right to make changes in materials or
design of the product at any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in this
written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days from
the date of purchase.
IMPORTANT: The Online Warranty Registration should be completed by the dealer at the time of
purchase. This information is necessary to provide you with quality customer service.
Model Number ____________________
4/17/19
Serial Number ____________________
PFL1242 Pallet Fork 319-211M
23
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement