Optoma X355 User Manual

advertisement

Optoma X355 User Manual
DLP® Projector
User manual
Table of Contents
SAFETY................................................................................................ 4
Important Safety Instruction....................................................................................................... 4
3D Safety Information................................................................................................................. 5
Copyright.................................................................................................................................... 6
Disclaimer................................................................................................................................... 6
Trademark Recognition.............................................................................................................. 6
FCC............................................................................................................................................ 7
Declaration of Conformity for EU countries................................................................................ 7
WEEE......................................................................................................................................... 7
INTRODUCTION................................................................................... 8
Package Overview..................................................................................................................... 8
Standard accessories................................................................................................................. 8
Optional accessories.................................................................................................................. 8
Product Overview....................................................................................................................... 9
Connections.............................................................................................................................. 10
Keypad...................................................................................................................................... 12
Remote control 1....................................................................................................................... 13
Remote control 2....................................................................................................................... 14
SETUP AND INSTALLATION.............................................................. 15
Installing the projector............................................................................................................... 15
Connecting sources to the projector.......................................................................................... 16
Adjusting the projector image.................................................................................................... 19
USING THE PROJECTOR................................................................... 22
Powering on / off the projector.................................................................................................. 22
Selecting an input source.......................................................................................................... 23
USING The projector................................................................... 24
Menu navigation and features................................................................................................... 24
OSD Menu tree......................................................................................................................... 25
Display image settings menu.................................................................................................... 34
Display 3D menu....................................................................................................................... 36
Display aspect ratio menu......................................................................................................... 37
Display edge mask menu.......................................................................................................... 40
Display zoom menu................................................................................................................... 40
Display image shift menu.......................................................................................................... 40
Display keystone menu............................................................................................................. 40
Audio mute menu...................................................................................................................... 41
Audio volume menu................................................................................................................... 41
Audio audio input 2 function menu............................................................................................ 41
2
English
Audio mic volume menu............................................................................................................ 41
Setup projection menu.............................................................................................................. 41
Setup screen type menu........................................................................................................... 41
Setup lamp settings menu......................................................................................................... 41
Setup filter settings menu.......................................................................................................... 42
Setup power settings menu....................................................................................................... 42
Setup security menu.................................................................................................................. 43
Setup test pattern menu............................................................................................................ 43
Setup remote settings menu..................................................................................................... 43
Setup projector ID menu........................................................................................................... 43
Setup options menu.................................................................................................................. 44
Setup reset menu...................................................................................................................... 45
Network LAN menu (for Type 2)................................................................................................ 45
Network control menu............................................................................................................... 46
Setup network control settings menu........................................................................................ 47
Info menu.................................................................................................................................. 52
maintenance................................................................................... 53
Replacing the lamp.................................................................................................................... 53
Installing and cleaning the dust filter......................................................................................... 55
additional information............................................................. 56
Compatible resolutions.............................................................................................................. 56
Image size and projection distance........................................................................................... 59
Projector dimensions and ceiling mount installation.................................................................. 61
IR remote control 1 codes......................................................................................................... 62
IR remote control 2 codes......................................................................................................... 64
Troubleshooting......................................................................................................................... 66
Warning indicators..................................................................................................................... 68
Specifications............................................................................................................................ 70
Optoma global offices................................................................................................................ 71
English
3
SAFETY
The lightning flash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Please follow all warnings, precautions and maintenance as recommended in this user's guide.
Important Safety Instruction
‡‡
Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from
over heating, it is recommended to install the projector in a location that does not block ventilation.
As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the
projector in an enclosure such as a book case or a cabinet that restricts air flow.
‡‡
To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture. Do not
install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers
that emits heat.
‡‡
Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short
out parts that could result in fire or electric shock.
‡‡
Do not use under the following conditions:
±±
In extremely hot, cold or humid environments.
(i) Ensure that the ambient room temperature is within 5°C ~ 40°C
(ii) Relative humidity is 10% ~ 85%
4
English
±±
In areas susceptible to excessive dust and dirt.
±±
Near any appliance generating a strong magnetic field.
±±
In direct sunlight.
‡‡
Do not use the projector in places where flammable gases or explosives gases may be present in the
atmosphere. The lamp inside the projector becomes very hot during operation and the gases may
ignite and result in a fire.
‡‡
Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be
(but not limited to):
±±
Unit has been dropped.
±±
Power supply cord or plug has been damaged.
±±
Liquid has been spilled on to the projector.
±±
Projector has been exposed to rain or moisture.
±±
Something has fallen in the projector or something is loose inside.
‡‡
Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the
projector may become damaged.
‡‡
Do not block the light coming out of the projector lens when in operation. The light will heat the object
and my melt, cause burns or start a fire.
‡‡
Please do not open or disassemble the projector as this may cause electric shock.
‡‡
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous
voltages or other hazards. Please call Optoma before you send the unit for repair.
‡‡
See projector enclosure for safety related markings.
‡‡
The unit should only be repaired by appropriate service personnel.
‡‡
Only use attachments/accessories specified by the manufacturer.
‡‡
Do not look into straight into the projector lens during operation. The bright light may harm your eyes.
‡‡
When replacing the lamp, please allow the unit to cool down. Follow instructions as described on
pages 53-54.
‡‡
This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows
warning messages.
‡‡
Reset the "Lamp Reset" function from the on-screen display "Setup lamp settings" menu after
replacing the lamp module.
‡‡
When switching the projector off, please ensure the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the projector to cool down.
‡‡
When the lamp is approaching to the end of its life time, the message "Lamp life exceeded." will show
on the screen. Please contact your local reseller or service center to change the lamp as soon as
possible.
‡‡
Turn off and unplug the power plug from the AC outlet before cleaning the product.
‡‡
Use a soft dry cloth with mild detergent to clean the display housing. Do not use abrasive cleaners,
waxes or solvents to clean the unit.
‡‡
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
Note: When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has been
replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages
53-54.
‡‡
Do not setup the projector in places where it might be subjected to vibration or shock.
‡‡
Do not touch the lens with bare hands
‡‡
Remove battery/batteries from remote control before storage. If the battery/batteries are left in the
remote for long periods, they may leak.
‡‡
Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it
can adversely affect the quality of the projector performance.
‡‡
Please follow the correct projector orientation installation as non standard installation may affect the
projector performance.
‡‡
Use a power strip and or surge protector. As power outages and brown-outs can KILL devices.
3D Safety Information
Please follow all warnings and precautions as recommended before you or your child use the 3D function.
Warning
Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be
closely supervised when viewing these images.
Photosensitive Seizure Warning and Other Health Risks
‡‡
Some viewers may experience an epileptic seizure or stroke when exposed to certain flashing images
or lights contained in certain Projector pictures or video games. If you suffer from, or have a family
history of epilepsy or strokes, please consult with a medical specialist before using the 3D function.
‡‡
Even those without a personal or family history of epilepsy or stroke may have an undiagnosed
condition that can cause photosensitive epileptic seizures.
‡‡
Pregnant women, the elderly, sufferers of serious medical conditions, those who are sleep deprived or
under the influence of alcohol should avoid utilizing the unit's 3D functionality.
‡‡
If you experience any of the following symptoms, stop viewing 3D pictures immediately and consult a
medical specialist: (1) altered vision; (2) light-headedness; (3) dizziness; (4) involuntary movements
such as eye or muscle twitching; (5) confusion; (6) nausea; (7) loss of awareness; (8) convulsions;
(9) cramps; and/ or (10) disorientation. Children and teenagers may be more likely than adults
to experience these symptoms. Parents should monitor their children and ask whether they are
experiencing these symptoms.
English
5
‡‡
Watching 3D projection may also cause motion sickness, perceptual after effects, disorientation, eye
strain and decreased postural stability. It is recommended that users take frequent breaks to lessen
the potential of these effects. If your eyes show signs of fatigue or dryness or if you have any of the
above symptoms, immediately discontinue use of this device and do not resume using it for at least
thirty minutes after the symptoms have subsided.
‡‡
Watching 3D projection while sitting too close to the screen for an extended period of time may
damage your eyesight. The ideal viewing distance should be at least three times the screen height. It
is recommended that the viewer's eyes are level with the screen.
‡‡
Watching 3D projection while wearing 3D glasses for an extended period of time may cause a
headache or fatigue. If you experience a headache, fatigue or dizziness, stop viewing the 3D
projection and rest.
‡‡
Do not use the 3D glasses for any other purpose than for watching 3D projection.
‡‡
Wearing the 3D glasses for any other purpose (as general spectacles, sunglasses, protective goggles,
etc.) may be physically harmful to you and may weaken your eyesight.
‡‡
Viewing in 3D projection may cause disorientation for some viewers. Accordingly, DO NOT place your
3D PROJECTOR near open stairwells, cables, balconies, or other objects that can be tripped over, run
into, knocked down, broken or fallen over.
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright
laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced
without written consent of the author.
© Copyright 2016
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations
or warranties with respect to the contents hereof and specifically disclaims any implied warranties of
merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication
and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending
applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
DLP , DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a
trademark of Texas Instruments.
All other product names used in this manual are the properties of their respective owners and are
Acknowledged.
DARBEE is a trademark by Darbee Products, Inc.
MHL, Mobile High-Definition Link and the MHL Logo are trademarks or registered trademarks of MHL Licensing,
LLC.
6
English
FCC
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be determined by turning the device off and on is
encouraged to try to correct the interference by one or more of the following measures:
‡‡
Reorient or relocate the receiving antenna.
‡‡
Increase the separation between the device and receiver.
‡‡
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
‡‡
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC
regulations.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is
granted by the Federal Communications Commission, to operate this projector.
Operation Conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque
l'intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
‡‡
EMC Directive 2004/108/EC (including amendments)
‡‡
Low Voltage Directive 2006/95/EC
‡‡
R & TTE Directive 1999/5/EC (if product has RF function)
WEEE
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure
utmost protection of the global environment, please recycle it.
English
7
INTRODUCTION
Package Overview
Carefully unpack and verify that you have the items listed below under standard accessories. Some of the items
under optional accessories may not be available depending on the model, specification and your region of
purchase. Please check with your place of purchase. Some accessories may vary from region to region.
The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.
Standard accessories
 CD User Manual
 Warranty Card*(1)
 Basic User Manual
Projector
Remote control *(2)
Power lead *(3)
Documentation
Note:
‡‡
The remote control is shipped with the battery.
‡‡
*(1) For European warranty information please visit www.optomaeurope.com.
‡‡
*(2) The actual remote control may vary depending on the region.
‡‡
*(3) Power lead is depending on the region.
Optional accessories
Carry bag
VGA cable
HDMI cable
Note: Optional accessories vary depending on model, specification and region.
8
English
Lens cap
INTRODUCTION
Product Overview
1
2
3
4
5
6
8
7
9
10
13
12
11
Note: Do not block projector inlet or outlet air vents.
No
Item
No
Item
1.
Lamp Cover
8.
Lens
2.
Focus Ring
9.
Ventilation (inlet)
3.
Zoom Lever
10. Ventilation (outlet)
4.
IR Receiver
11. KensingtonTM Lock Port
5.
Keypad
12. Power Socket
6.
Tilt-Adjustment Foot
13. Input / Output
7.
Security Bar
English
9
INTRODUCTION
Connections
Type 1 XGA/ WXGA
2b
HDMI
3
4b
6
VGA-OUT / YPbPr
VGA-IN / YPbPr
USB Power
Out (5V
13
VIDEO
8
7
Audio In
Audio Out
1.0A)
MOUSE /
SERVICE
RS-232C
14
12
11
Type 2 XGA/ WXGA
1
2a
HDMI 1 / MHL
HDMI 2
3
4a
USB Power
Out (5V
5
VGA-IN 1 / YPbPr
VGA-IN 2 / YPbPr
VGA-OUT / YPbPr
RS-232C
6
VIDEO
S-VIDEO
7
8
Audio Out
14
10 English
Audio In
1.0A)
MOUSE /
SERVICE
Audio In /Mic In
13
12
11
RJ-45
10
9
INTRODUCTION
No
Item
Regulatory Name
Type 1 XGA/
WXGA
Type 2 XGA/
WXGA
N/A
√
1.
HDMI 1 / MHL Connector
2.
a) HDMI 2 Connector
b) HDMI Connector
√
√
3.
USB Power Out (5V 1A) Connector / MOUSE / SERVICE
Connector
√*
√*
a) VGA-IN 1 / YPbPr Connector and
VGA-IN 2 / YPbPr Connector
b) VGA-IN / YPbPr Connector
√
√ (x2)
N/A
√
4.
5.
S-VIDEO Connector
6.
Composite Connector
√
√
7.
Audio Out Connector
√
√
8.
Audio In Connector
√
√ (x2)
9.
Audio In / Mic In Connector
N/A
√
N/A
√
11. RS-232C Connector
√
√
12. Kensington
√
√
13. VGA-OUT / YPbPr Connector
√
√
14. Power Socket
√
√
10. RJ-45 Connector
TM
Lock Port
Note: “√” means the item is supported, “N/A” means the item is not available.
Note:
‡‡
Remote mouse requires special remote control.
‡‡
*This model supports mouse / service capability.
English
11
INTRODUCTION
Keypad
1
2
3
4
11
5
10
6
9
8
No
12 English
Item
7
No
Item
1.
On/Standby LED
7.
Enter
2.
Lamp LED
8.
Menu
3.
Keystone Correction
9.
Four Directional Select Keys
4.
Temp LED
10. Source
5.
Information
11. Power
6.
Re-Sync
INTRODUCTION
Remote control 1
10
11
1
12
2
13
3
14
4
4
5
6
15
2
7
16
8
17
9
18
No
Item
No
Item
1.
Power On / Off
10. IR LED Indicator
2.
Keystone + / -
11.
3.
AV Mute
12. Aspect Ratio
4.
Volume - / +
13. Mute
5.
Enter
14. Four Directional Select Keys
6.
Menu
15. 3D
7.
HDMI
16. Video
8.
VGA
17. Resync
9.
Source
18. Brightness Mode
Freeze
Note:
The actual remote control may vary depending on the region.
‡‡
Some keys may have no function for models that do not support these features.
‡‡
Before using the remote control for the first time, remove the transparent insulation tape. See page 20
for battery installation.
S
LT
3V
O
C
R
20
2
5
‡‡
English
13
INTRODUCTION
Remote control 2
1
Power
Switch
16
2
Freeze
3
4
17
L
R
18
5
19
Enter
6
7
8
9
10
11
12
13
14
Laser
Page+
V Keystone
-
-
+
1
Page-
20
Volume
+
21
2
3
Menu
3D
4
5
6
23
HDMI
VGA
Video
24
7
8
9
User1
User2
User3
25
26
0
Source
22
Resync
27
15
No
Item
No
Item
1.
Power On / Off
15. Brightness Mode
2.
Freeze
16. Mouse On / Off
3.
Display Blank / Audio Mute
17. Mute
4.
Mouse Left Click
18. Mouse Right Click
5.
Enter
19. Four Directional Select Keys
6.
Laser
20. Page -
7.
Page +
21. Volume - / +
8.
V Keystone - / +
22. 3D Menu On / Off
9.
Menu
23. VGA
10.
Aspect Ratio
24. Video
11.
HDMI
25. User 3
12.
User 2
26. Numeric Keypad (0-9)
13.
User 1
27. Resync
14.
Source
Note:
‡‡
‡‡
14 English
The actual remote control may vary depending on the region.
Some keys may have no function for models that do not support these features
SETUP AND INSTALLATION
Installing the projector
Your projector is designed to be installed in one of four possible positions.
Your room layout or personal preference will dictate which installation location you select. Take into consideration
the size and position of your screen, the location of a suitable power outlet, as well as the location and distance
between the projector and the rest of your equipment.
Table mount front
Ceiling mount front
Table mount rear
Ceiling mount rear
Projector should be placed flat on a surface and 90 degrees / perpendicular to the screen.
‡‡
How to determine projector location for a given screen size, please refer to distance table on pages
59-60.
‡‡
How to determine screen size for a given distance, please refer to distance table on pages 59-60.
Note: The further away the projector is placed from the screen the projected image size increases and vertical
offset also increases proportionally.
IMPORTANT!
Do not operate the projector in any orientation other that table top or ceiling mount. The projector should
be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate
the warranty and may shorten the lifetime of the projector lamp or the projector itself. For none standard
installation advise please contact Optoma.
English
15
SETUP AND INSTALLATION
Connecting sources to the projector
Type 1 XGA/ WXGA
3
13
6
2
HDMI
VGA-IN / YPbPr
USB Power
Out (5V
VGA-OUT / YPbPr
VIDEO
Audio In
Audio Out
1.0A)
MOUSE /
SERVICE
RS-232C
15
MOLEX
4
14
16
12
MOLEX
16 English
7
11
9
SETUP AND INSTALLATION
Type 2 XGA/ WXGA
4
3
1
5
2
HDMI 1 / MHL
HDMI 2
7
USB Power
Out (5V
VGA-IN 2 / YPbPr
VGA-IN 1 / YPbPr
S-VIDEO
VIDEO
Audio Out
6
Audio In
1.0A)
MOUSE /
SERVICE
Audio In /Mic In
RS-232C
VGA-OUT / YPbPr
RJ-45
MOLEX
15
13
14
12
11
10
9
8
16
MOLEX
No
Item
Regulatory Name
Type 1 XGA/
WXGA
Type 2 XGA/
WXGA
1.
MHL Cable
N/A
√
2.
HDMI Cable
√
√
3.
RCA Component Cable
√
√
4.
VGA In Cable
√
√
5.
S-Video Cable
N/A
√
6.
Video Cable
√
√
7.
Audio In Cable
√
√
8.
Microphone In Cable
N/A
√
9.
Audio Out Cable
√
√
English
17
SETUP AND INSTALLATION
No
Item
10. RJ-45 Cable
Regulatory Name
Type 1 XGA/
WXGA
Type 2 XGA/
WXGA
N/A
√
11. RS232C Cable
√
√
12. USB Cable (mouse control)
√
√
13. VGA Out Cable
√
√
14. USB Power Cable
√
√
15. HDMI Stick
√
√
16. Power Cord
√
√
Note: “√” means the item is supported, “N/A” means the item is not available.
18 English
SETUP AND INSTALLATION
Adjusting the projector image
Image height
The projector is equipped with elevator feet for adjusting the image height.
1.
2.
Locate the adjustable foot you wish to adjust on the underside of the projector.
Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
Zoom and focus
‡‡
To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease
the projected image size.
‡‡
To adjust the focus, turn the focus ring clockwise or counterclockwise until the image is sharp and
legible.
Zoom Lever
Focus Ring
Note: The projector will focus at a distance of 1m to 10m.
English
19
SETUP AND INSTALLATION
Installing / replacing the batteries
20
25
R
LT
S
20
25
LT
R
O
C
3V
S
20
LT
R
M
25
Put the cover back.
3V
O
3.
Install new battery into the compartment. Remove the old battery and
install new one (CR2025). Ensure that the side with a “+” is facing
up.
C
2.
2- L iC E L L 3 V
O
M nO
S JAPAN H
Press firmly and slide the battery cover off.
C
1.
CAUTION: To ensure safe operation, please observe the following precautions:
20 English
‡‡
Use CR2025 type battery.
‡‡
Avoid contact with water or liquid.
‡‡
Do not expose the remote control to moisture or heat.
‡‡
Do not drop the remote control.
‡‡
If the battery has leaked in the remote control, carefully wipe the case clean and install new battery.
‡‡
Risk of an explosion if battery is replaced by an incorrect type.
‡‡
Dispose of used battery according to the instructions.
SETUP AND INSTALLATION
Effective range
Infra-Red (IR) remote control sensor is located on top of the projector. Ensure to hold the remote control at an
angle within 30 degrees perpendicular to the projector’s top IR remote control sensor to function correctly. The
distance between the remote control and the sensor should not be longer than 6 meters (~ 20 feet).
Note: When pointing the remote control directly (0 degrees angle) on the IR sensor, the distance between the
remote control and the sensor should not be longer than 8 meters (~ 26 feet).
‡‡
Make sure that there are no obstacles between the remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
‡‡
Make sure the IR transmitter of the remote control is not being shined by sunlight or fluorescent lamps
directly.
‡‡
Please keep the remote controller away from fluorescent lamps for over 2 meters or the remote
controller might become malfunction.
‡‡
If the remote control is close to Inverter-Type fluorescent lamps, it might become ineffective from time
to time.
‡‡
If the remote control and the projector are within a very short distance, the remote control might
become ineffective.
‡‡
When you aim at the screen, the effective distance is less than 6 meters from the remote control to the
screen and reflecting the IR beams back to the projector. However, the effective range might change
according to screens.
Approx.
15°
English
21
USING THE PROJECTOR
Powering on / off the projector
or
Powering on
1.
Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will
turn red.
2.
Turn on the projector by pressing the " " either on the projector keypad or the remote control.
3.
A start up screen will display in approximately 10 seconds and the On/Standby LED will be flashing
green or flashing blue.
Note: The first time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1.
Turn off the projector by pressing the " " either on the projector keypad or the remote control.
2.
The following message will be displayed:
Power Off
Power Off?
Press power key again.
3.
4.
5.
Press the " " again to confirm, otherwise the message will disappear after 15 seconds. When you
press the " " button for the second time, the projector will shut down.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/
Standby LED will flash green or flash blue. When the On/Standby LED turns solid red, this indicates
the projector has entered standby mode. If you wish to turn the projector back on, you must wait until
the cooling cycle has finished and the projector has entered standby mode. When the projector is in
standby mode, simply press the " " button again to turn on the projector.
Disconnect the power lead from the electrical outlet and the projector.
Note: It is not recommended that the projector is turned on immediately, right after a power off procedure.
22 English
USING THE PROJECTOR
Selecting an input source
Turn on the connected source that you want to display on the screen, such as computer, notebook, video player,
etc. The projector will automatically detect the source. If multiple sources are connected, push the source button on
the projector keypad or the remote control to select the desired input.
or
English
23
USING The projector
Menu navigation and features
The projector has multilingual on-screen display menus that allow you to make image adjustments and change a
variety of settings. The projector will automatically detect the source.
1.
To open the OSD menu, press
2.
When OSD is displayed, use
on a particular page, press
3.
Use
keys to select the desired item in the sub menu and then press
settings. Adjust the settings by using
keys.
4.
Select the next item to be adjusted in the sub menu and adjust as described above.
5.
Press the
6.
To exit, press the
the new settings.
or
on the remote control or the projector keyboard.
or
keys to select any item in the main menu. While making a selection
key to enter sub menu.
or
key to view further
to confirm, and the screen will return to the main menu.
or
again. The OSD menu will close and the projector will automatically save
Settings
Sub Menu
Display
Image Settings
3D
Main Menu
Aspect Ratio
Edge Mask
Zoom
Image Shift
Keystone
Select
Exit
Navigation guide
24 English
Enter
USING THE PROJECTOR
OSD Menu tree
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Presentation
Bright
Cinema
Game
Display Mode
[Data]
sRGB
DICOM
USER
3D
Off [Default]
BlackBoard
Light Yellow
Wall Color [Data]
Light Green
Light Blue
Pink
Gray
Display
Image Settings
Brightness
-50~50
Contrast
-50~50
Sharpness
1~15
Color
-50~50
Tint
-50~50
Film
Video
Graphics
Gamma
Standard(2.2)
1.8
2.0
2.4
BrilliantColorTM
Color Settings
Color
Temperature
[Data model]
1~10
Warm
Medium
Cool
English
25
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
R [Default]
G
B
Color
C
Y
M
W
Color Matching
Saturation
-50~50 [Default:0]
Hue
-50~50 [Default:0]
Gain
-50~50 [Default:0]
Reset
Cancel [Default]
Yes
Exit
RGB Gain/Bias
Display
Image Settings
Color Settings
Red Gain
-50~50
Green Gain
-50~50
Blue Gain
-50~50
Red Bias
-50~50
Green Bias
-50~50
Blue Bias
-50~50
Reset
Cancel [Default]
Yes
Exit
Color Space [Not
HDMI Input]
Auto [Default]
RGB
YUV
Auto [Default]
Color Space
[HDMI Input]
RGB(0~255)
RGB(16~235)
YUV
Normal [Default]
RGB Channel
Red
Green
Blue
White Level
-50~50
Black Level
-50~50
Saturation
-50~50
Hue
-50~50
IRE
Exit
26 English
0
7.5
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Automatic
Signal
Image Settings
Sub Menu 4
Values
Off
On [Default]
Frequency
0~100 [Default: 0]
Phase
-50~50 [Default: 0]
H. Position
-50~50 [Default: 0]
V. Position
-50~50 [Default: 0]
Exit
Bright [Default]
Brightness Mode
[Lamp Base Data]
Eco
Dynamic
Eco+
Reset
Off
3D Mode
DLP [Default]
IR
3D [Default]
3D->2D
L
R
3D
Auto [Default]
3D Format
Display
SBS
Top and Bottom
Frame Sequential
3D sync invert
On
Off [Default]
4:3
16:9
16:10 [WXGA models]
Aspect Ratio
LBX [except XGA models]
Native
Auto
Edge Mask
0~10 [Default: 0]
Zoom
-5~25 [Default: 0]
H: 0; V: -100
H: -100; V: 0
H: 100; V: 0
Image shift
H: 0; V: 100
H: -100; V: 0
[Default:0]
H: 0; V: -100
H: 100; V: 0
H: 0; V: 100
Keystone
-40~40 [Default:0]
English
27
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Values
Off [Default]
Mute
Audio
Sub Menu 4
On
Volume
0-10 [Default: 5]
Audio Input 2
Function
Audio 2 [Default]
Mic Volume
0-10 (Type 2) [Default: 5]
Mic (Type 2)
Front
[Default]
Rear
Projection
Ceiling-top
Rear-top
Screen Type
16:9
[WXGA model]
16:10 [Default]
Off
Lamp Reminder
On [Default]
Lamp Settings
Cancel [Default]
Lamp Reset
Yes
Yes
Optional Filter
Installed
No
Filter Usage
Hours
(Read only)
Off
300hr
Filter Settings
Filter Reminder
Setup
500hr [Default]
800hr
1000hr
Cancel [Default]
Filter Reset
Yes
Off [Default]
Direct Power On
On
Off [Default]
Signal Power On
On
0~180 (5 min increments)
[Default: 0]
Auto Power Off
(min)
Power Settings
Sleep Timer
(min)
Quick Resume
Power Mode
(Standby)
28 English
0~990 (30 min increments)
[Default: 0]
Always On
Yes
No [Default]
Off
On [Default]
Active
Eco [Default]
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Security
Month
Security
Security Timer
Day
Hour
Change
Password
Green Grid
Magenta Grid
Test Pattern
White Grid
White
Off
IR Function
On
Off
HDMI 2
Test Pattern
Brightness
Contrast
Sleep Timer
Color Matching
User1
Setup
Color Temp
Gamma
Source Lock
Projection
Lamp Settings
Remote
Settings
Zoom
Freeze
[depends on
remote]
HDMI 2
Test Pattern
Brightness
Contrast
Sleep Timer
Color Matching
User2
Color Temp
Gamma
Source Lock
Projection
Lamp Settings
Zoom
Freeze
English
29
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
HDMI 2
Test Pattern
Brightness
Contrast
Sleep Timer
Remote
Settings
[depends on
remote]
Color Matching
User3
Color Temp
Gamma
Source Lock
Projection
Lamp Settings
Zoom
Freeze
Projector ID
00~99
English [Default]
Deutsch
Français
Italiano
Español
Português
Polski
Setup
Nederlands
Svenska
Norsk
Dansk
Suomi
ελληνικά
Options
Language
繁體中文
簡体中文
日本語
한국어
Русский
Magyar
Čeština
ไทย
Türkçe
Vietnamese
Indonesia
Romanian
Slovakian
30 English
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
CC1
Closed
Captioning
CC2
Off [Default]
Top left
Top right
Menu Location
Center
[Default]
Bottom left
Menu Settings
Bottom right
Off
Menu Timer
5sec
10sec [Default]
HDMI
HDMI/MHL (Type 2)
VGA
Input Source
VGA1 (Type 2)
S-Video (Type 2)
Video
HDMI
HDMI1
Setup
Options
HDMI/MHL
VGA
Input Name
VGA1
Video
Wireless
Network Display
Default [Default]
Custom
Default [Default]
Custom
Default [Default] (Type 2)
Custom (Type 2)
Default [Default]
Custom
Default [Default] (Type 2)
Custom (Type 2)
Default [Default]
Custom
Default [Default]
Custom
Default [Default]
Custom
Auto [Default]
VGA Out
VGA1
VGA2
High Altitude
Display Mode
Lock
Keypad Lock
Information Hide
Off [Default]
On
Off [Default]
On
Off [Default]
On
Off [Default]
On
English
31
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Default [Default]
Logo
Neutral
User
Logo Capture
Options
Cancel [Default]
Yes
None [Default]
Blue
Setup
Background
Color
Red
Green
Grey
Logo
Reset OSD
Reset
Reset to Default
Yes
Cancel [Default]
Yes
Network Status
(read only)
MAC Address
(read only)
DHCP
LAN
Cancel [Default]
Off [Default]
On
IP Address
192.168.0.100 [Default]
Subnet Mask
255.255.255.0 [Default]
Gateway
192.168.0.254 [Default]
DNS
192.168.0.51 [Default]
Apply
Reset
Off
Crestron
Network
(for Type
2)
On [Default]
NOTE: Port 41794.
Off
Extron
On [Default]
NOTE: Port 2023.
Off
PJ Link
Control
AMX Device
Discovery
On [Default]
NOTE: Port 4352
Off
On [Default]
NOTE: Port 9131
Off
Telnet
On [Default]
NOTE: Port 23
Off
HTTP
32 English
On [Default]
NOTE: Port 80
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Regulatory
Serial Number
Current Input
Source
Resolution
00x00
Refresh Rate
0.00Hz
Network Status
IP Address
Projector ID
00~99
Remote Code
00~99
NOTE: Show remote in system.
Remote Code
(Active)
00~99
NOTE: Show remote from Remote.
Display Mode
Information Power
mode(standby)
Brightness
Mode
Filter Hours
Lamp Hours
Bright mode
0H
Eco mode
0H
Dynamic mode
0H
Eco+ mode
0H
Total hours
System
FW Version
LAN
MCU
Update
Note:
‡‡
The “LAMP RESET” in OSD will only reset both Lamp Hours in OSD and Lamp Hours in service
mode. The Projection Hours in service mode will not be reset.
‡‡
Each display mode can be adjusted and saved the value.
‡‡
In 3D timing mode, the zoom/edge mask will be disabled to prevent from image break.
English
33
USING THE PROJECTOR
Display menu
Display image settings menu
Display Mode
There are many factory presets optimized for various types of images.
‡‡
Presentation: This mode is suitable for showing PowerPoint presentations when the projector is
connected to the PC.
‡‡
Bright: Maximum brightness from PC input.
‡‡
Cinema: Select this mode for home theater.
‡‡
Game: Select this mode to increase the brightness and response time level for enjoying video games.
‡‡
sRGB: Standardized accurate color.
‡‡
DICOM: This mode can project a monochrome medical image such as an X ray radiography, MRI, etc.
‡‡
USER: Memorize user’s settings.
‡‡
3D: To experience the 3D effect, you need to have 3D glasses. Make sure your PC/portable device
has a 120 Hz signal output quad buffered graphics card and a 3D Player installed.
Wall Color (Data mode)
Use this function to obtain an optimized screen image according to the wall color. Select between off, blackboard,
light yellow, light green, light blue, pink, and gray.
Brightness
Adjust the brightness of the image.
Contrast
The contrast controls the degree of difference between the lightest and darkest parts of the picture.
Sharpness
Adjust the sharpness of the image.
Color
Adjust a video image from black and white to fully saturated color.
Tint
Adjust the color balance of red and green.
Gamma
Set up gamma curve type. After the initial setup and fine tuning is completed, utilize the Gamma Adjustment steps
to optimize your image output.
34 English
‡‡
Film: For home theater.
‡‡
Video: For video or TV source.
‡‡
Graphics: For PC / Photo source.
‡‡
Standard(2.2): For standardized setting.
‡‡
1.8/ 2.0/ 2.4: For specific PC / Photo source.
USING THE PROJECTOR
Color Settings
Configure the color settings.
‡‡
BrilliantColorTM: This adjustable item utilizes a new color-processing algorithm and enhancements to
enable higher brightness while providing true, more vibrant colors in picture.
‡‡
Color Temperature (data-mode only): Select a color temperature from Warm, Medium, or Cool.
‡‡
Color Matching: Select the following options:
±±
Color: Adjust the red (R), green (G), black (B), cyan (C), yellow (Y), magenta (M), and white (W)
level of the image.
‡‡
±±
Saturation: Adjust a video image from black and white to fully saturated color.
±±
Hue: Adjust the color balance of red and green.
±±
Gain: Adjust the image brightness.
±±
Reset: Return the factory default settings for color matching.
±±
Exit: Exit the “Color Matching” menu.
RGB Gain/Bias: This settings allows to configure the brightness (gain) and contrast (bias) of an
image.
±±
Reset: Return the factory default settings for RGB gain/bias.
±±
Exit: Exit the “RGB Gain/Bias” menu.
‡‡
Color Space (non-HDMI input only): Select an appropriate color matrix type from the following:
AUTO, RGB, or YUV.
‡‡
Color Space (HDMI input only): select an appropriate color matrix type from the following: Auto,
RGB(0-255), RGB(16-235), and YUV.
‡‡
RGB Channel: Select from normal, red, green, or blue channels.
‡‡
White Level: Allow user to adjust White Level when inputting Video signals.
‡‡
Black Level: Allow user to adjust Black Level when inputting Video signals.
‡‡
Saturation: Adjust a video image from black and white to fully saturated color.
‡‡
Hue: Adjust the color balance of red and green.
‡‡
IRE: Allow user to adjust IRE value when inputting Video signals.
Note: IRE is only available with NTSC video format.
‡‡
Signal
Exit: Exit the “Color Settings” menu.
Adjust the signal options.
‡‡
Automatic: Configure automatically the signal (the frequency and phase items are grayed out). If
automatic is disabled, the frequency and phase items will appear for tuning and saving the settings.
‡‡
Frequency: Change the display data frequency to match the frequency of your computer’s graphic
card. Use this function only if the image appears to flicker vertically.
‡‡
Phase: Synchronize the signal timing of the display with the graphic card. If the image appears to be
unstable or flickers, use this function to correct it.
‡‡
H. Position: Adjust the horizontal positioning of the image.
‡‡
V. Position: Adjust the vertical positioning of the image.
‡‡
Exit: Exit the “Signal” menu.
English
35
USING THE PROJECTOR
Brightness Mode (Lamp base data)
Adjust the brightness mode settings for lamp-based projectors.
‡‡
Bright: Choose “Bright” to increase the brightness.
‡‡
Eco: Choose “Eco” to dim the projector lamp which will lower power consumption and extend the lamp
life.
‡‡
Dynamic: Choose “Dynamic” to dim the lamp power which will be based on brightness level of the
content and adjust lamp power consumption between 100% and 30% dynamically. The lamp life will
be extended.
‡‡
Eco+: When Eco+ mode is activated, the brightness level of the content is automatically detected to
significantly reduced lamp power consumption (up to 70%) during periods of inactivity.
Reset
Return the factory default settings for color settings.
Display 3D menu
3D Mode
Use this option to disable the 3D function or select the appropriate the 3D function.
‡‡
Off: Select “Off” to turn off 3D mode.
‡‡
DLP: Select to use optimized settings for DLP 3D Glasses.
‡‡
IR: Select “IR” to use optimized setting for IR 3D Glasses.
3D → 2D
Use this option to specify how the 3D content should appear on the screen.
‡‡
3D: Display 3D signal.
‡‡
L (Left): Display the left frame of 3D content.
‡‡
R (Right): Display the right frame of 3D content.
3D Format
Use this option to select the appropriate 3D format content.
‡‡
Auto: When a 3D identification signal is detected, the 3D format is selected automatically.
‡‡
SBS: Display 3D signal in “Side-by-Side” format.
‡‡
Top and Bottom: Display 3D signal in “Top and Bottom” format.
‡‡
Frame Sequential: Display 3D signal in “Frame Sequential” format.
3D Sync Invert
Use this option to enable/disable the 3D sync invert function.
36 English
USING THE PROJECTOR
Display aspect ratio menu
Aspect Ratio
Select the aspect ratio of the displayed image between the following options:
‡‡
4:3: This format is for 4:3 input sources.
‡‡
16:9: This format is for 16:9 input sources, like HDTV and DVD enhanced for Wide screen TV.
‡‡
16:10 (for WXGA models only): This format is for 16:10 input sources, like widescreen laptops.
‡‡
LBX (except XGA models): This format is for non-16x9, letterbox source and if you use external 16x9
lens to display 2.35:1 aspect ratio in full resolution.
‡‡
Native: This format displays the original image without any scaling.
‡‡
Auto: Automatically selects the appropriate display format.
‡‡
Detailed informations about LBX mode:
±±
Some Letter-Box Format DVDs are not enhanced for 16x9 TVs. In this situation, the image
will not look right when displaying image in 16:9 mode. In this situation, please try to use the
4:3 mode to view the DVD. If the content is not 4:3, there will be black bars around the image
in 16:9 display. For this type of content, you can use LBX mode to fill the image on the 16:9
display.
Note:
±±
‡‡
If you use an external anamorphic lens, this LBX mode also allows you to watch a 2.35:1
content (include Anamorphic DVD and HDTV film source) that supports anamorphic wide is
enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Lamp
power and vertical resolution are fully utilized.
To use the superwide format, do the following:
a)
Set the screen aspect ratio to 2.0:1.
b)
Select “Superwide” format.
c)
Align the projector image correctly on the screen.
XGA scaling table:
Source
480i/p
4x3
Scale to 1024x768.
16x9
Scale to 1024x576.
Native
Auto
576i/p
1080i/p
720p
No scaling will be made; the image is displayed with the resolution based on input source.
-If source is 4:3, the screen type will be scaled to 1024x768.
-If source is 16:9, the screen type will be scaled to 1024x576.
-If source is 15:9, the screen type will be scaled to 1024x614.
-If source is 16:10, the screen type will be scaled to 1024x640.
English
37
USING THE PROJECTOR
XGA auto mapping rule:
Input resolution
Auto
4:3
Wide Laptop
SDTV
HDTV
Auto/Scale
H-resolution
V-resolution
1024
768
640
480
1024
768
800
600
1024
768
1024
768
1024
768
1600
1200
1024
768
1280
720
1024
576
1280
768
1024
614
1280
800
1024
640
720
576
1024
576
720
480
1024
576
1280
720
1024
576
1920
1080
1024
576
WXGA scaling table (screen type 16:10):
Note:
‡‡
Supported screen type 16:9 (1280x720), 16:10 (1280x800).
‡‡
When screen type is 16:9, the16x10 format becomes unavailable.
‡‡
When screen type is 16:10, the 16x9 format becomes unavailable.
‡‡
If you select auto option then the display mode will be also automatically changed.
16 : 10 screen
480i/p
4x3
Scale to 1066x800.
16x10
Scale to 1280x800.
LBX
Native mode
Auto
576i/p
1080i/p
720p
Scale to 1280x960, then get the central 1280x800 image to display.
1:1 mapping centered.
1:1 mapping
display
1280x800.
1280x720
centered.
1:1 mapping
centered.
-Input source will be fit into 1280x800 display area and be kept its original aspect ratio.
-If source is 4:3, the screen type will be scaled to 1066x800.
-If source is 16:9, the screen type will be scaled to 1280x720.
-If source is 15:9, the screen type will be scaled to 1280x768.
-If source is 16:10, the screen type will be scaled to 1280x800.
38 English
PC
USING THE PROJECTOR
WXGA auto mapping rule (screen type 16:10):
Auto
4:3
Wide Laptop
SDTV
HDTV
Input resolution
Auto/Scale
H-resolution
V-resolution
1280
800
640
480
1066
800
800
600
1066
800
1024
768
1066
800
1280
1024
1066
800
1400
1050
1066
800
1600
1200
1066
800
1280
720
1280
720
1280
768
1280
768
1280
800
1280
800
720
576
1280
720
720
480
1280
720
1280
720
1280
720
1920
1080
1280
720
WXGA scaling table (screen type 16:9):
16 : 9 screen
480i/p
576i/p
1080i/p
720p
4x3
Scale to 960x720.
16x9
Scale to 1280x720.
LBX
Scale to 1280x960, then get the central 1280x720 image to display.
Native mode
Auto
1:1 mapping centered.
1:1 mapping
display
1280x720.
1280x720
centered.
PC
1:1 mapping
centred.
-If this format is select, screen type will automatically become 16:9 (1280x720).
-If source is 4:3, the screen type will be scaled to 960x720.
-If source is 16:9, the screen type will be scaled to 1280x720.
-If source is 15:9, the screen type will be scaled to 1200x720.
-If source is 16:10, the screen type will be scaled to 1152x720.
English
39
USING THE PROJECTOR
WXGA auto mapping rule (screen type 16:9):
Auto
4:3
Wide Laptop
SDTV
HDTV
Input resolution
Auto/Scale
H-resolution
V-resolution
1280
720
640
480
960
720
800
600
960
720
1024
768
960
720
1280
1024
960
720
1400
1050
960
720
1600
1200
960
720
1280
720
1280
720
1280
768
1200
720
1280
800
1152
720
720
576
1280
720
720
480
1280
720
1280
720
1280
720
1920
1080
1280
720
Display edge mask menu
Edge Mask
Use this function to remove the video encoding noise on the edge of video source.
Display zoom menu
Zoom
Use to reduce or magnify an image on the projection screen.
Display image shift menu
Image Shift
Adjust the projected image position horizontally (H) or vertically (V).
Display keystone menu
Keystone
Adjust the image distortion caused by tilting the projector.
40 English
USING THE PROJECTOR
Audio menu
Audio mute menu
Mute
Use this option to temporarily turn off the sound.
‡‡
On: Choose the “On” to turn mute on.
‡‡
Off: Choose the “Off” to turn mute off.
Note: “Mute” function affects both internal and external speaker volume.
Audio volume menu
Volume
Adjust the audio volume level.
Audio audio input 2 function menu
Audio Input 2 Function
Select the port between Audio 2 and Mic (Type 2).
Audio mic volume menu
Mic Volume
Adjust the microphone volume level (Type 2).
Setup menu
Setup projection menu
Projection
Select the preferred projection between front, rear, ceiling-top, and rear-top.
Setup screen type menu
Screen Type (for WXGA model only)
Choose the screen type from 16:9 and 16:10.
Setup lamp settings menu
Lamp Reminder
Choose this function to show or to hide the warning message when the changing lamp message is displayed. The
message will appear 30 hours before suggested replacement of lamp.
Lamp Reset
Resets the lamp hour counter after replacing the lamp.
English
41
USING THE PROJECTOR
Setup filter settings menu
Optional Filter Installed
Set the warning message setting.
‡‡
Yes: Display warning message after 500 hours of use.
Note: “Filter Usage Hours / Filter Reminder / Filter Reset” will only appear when “Optional Filter Installed” is “Yes”.
‡‡
No: Turn off warning message.
Filter Usage Hours
Display the filter time.
Filter Reminder
Choose this function to show or hide the warning message when the changing filter message is displayed. The
available options include 300hr, 500hr, 800hr, and 1000hr.
Filter Reset
Reset the dust filter counter after replacing or cleaning the dust filter.
Setup power settings menu
Direct Power On
Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied,
without pressing the “Power” key on the projector keypad or on the remote control.
Signal Power On
Choose “On” to activate Signal Power mode. The projector will automatically power on when a signal is detected,
without pressing the “Power” key on the projector Keypad or on the remote control.
Note: If the “Signal Power On” option is turned “On”, the power consumption of the projector in standby mode will
be over 3W.
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the
projector. The projector will automatically power off when the countdown has finished (in minutes).
Sleep Timer (min)
Configure the sleep timer.
‡‡
Sleep Timer (min): Sets the countdown timer interval. The countdown timer will start, with or without
a signal being sent to the projector. The projector will automatically power off when the countdown has
finished (in minutes).
Note: The Sleep Timer is reset every time when the projector is powered off.
‡‡
Always On: Check to set the sleep timer always on.
Quick Resume
Set the quick resume setting.
42 English
‡‡
On: If the projector is accidentally turned off, this feature allows the projector to be instantly powered
on again, if selected within a period of 100 seconds.
‡‡
Off: The fan will start cooling the system after 10 seconds when user turns off the projector.
USING THE PROJECTOR
Power Mode (Standby)
Set the power mode setting.
‡‡
Active: Choose “Active” to return to normal standby.
‡‡
Eco.: Choose “Eco.” to save power dissipation further < 0.5W.
Note: The fans will still run in active standby if “Signal Power On” is enabled.
Setup security menu
Security
Enable this function to prompt for a password before using the projector.
‡‡
On: Choose “On” to use security verification when the turning on the projector.
‡‡
Off: Choose “Off” to be able to switch on the projector without password verification.
Security Timer
Can be select the time (Month/Day/Hour) function to set the number of hours the projector can be used. Once this
time has elapsed you will be requested to enter your password again.
Change Password
Use to set or modify the password that is prompted when turning the projector on.
Setup test pattern menu
Test Pattern
Select the test pattern from green grid, magenta grid, white grid, white or disable this function (off).
Setup remote settings menu
IR Function
Set the IR function setting.
‡‡
On: Choose “On”, the projector can be operated by the remote control from top IR receiver.
‡‡
Off: Choose “Off”, the projector can’t be operated by the remote control. By selecting “Off”, you will be
able to use the Keypad keys.
User1/ User2/ User3
Assign the default function for User1, User2, or User3 between HDMI 2, test pattern, brightness, contrast, sleep
timer, color matching, color temp, gamma, source lock, projection, lamp settings, zoom, and freeze.
Setup projector ID menu
Projector ID
ID definition can be set up by menu (range 0-99), and allow user control an individual projector by using RS232 command.
English
43
USING THE PROJECTOR
Setup options menu
Language
Select the multilingual OSD menu between English, German, French, Italian, Spanish, Portuguese, Polish, Dutch,
Swedish, Norwegian/Danish, Finnish, Greek, traditional Chinese, simplified Chinese, Japanese, Korean, Russian,
Hungarian, Czechoslovak, Arabic, Thai, Turkish, Farsi, Vietnamese, Indonesian, Romanian, and Slovakian.
Closed Captioning
Closed Captioning is a text version of the program sound or other information displayed on the screen. If the input
signal contains closed captions, you can turn on the feature and watch the channels. The available options include
“Off”, “CC1”, and “CC2”.
Menu Settings
Set the menu location on the screen and configure menu timer settings.
‡‡
Menu Location: Select the menu location on the display screen.
‡‡
Menu Timer: Set the duration where the OSD menu stays visible on the screen.
Input Source
Select the input source between HDMI, HDMI/MHL (Type 2), VGA, VGA1 (Type 2), S-video (Type 2), video.
Input Name
Use to rename the input function for easier identification. The available options include HDMI, HDMI1, HDMI/MHL
(Type 2), VGA, VGA1 (Type 2), video, wireless, network display.
VGA Out
Select the VGA out source between VGA1, VGA2, or set the source automatically (Auto).
High Altitude
When “On” is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin.
Display Mode Lock
Choose “On” or “Off” to lock or unlock adjusting display mode settings.
Keypad Lock
When the keypad lock function is “On”, the Keypad will be locked. However, the projector can be operated by the
remote control. By selecting “Off”, you will be able to reuse the Keypad.
Information Hide
Enable this function to hide the information message.
‡‡
Off: Choose “On” to hide the info message.
‡‡
On: Choose “Off” to show the “searching” message.
Logo
Use this function to set the desired startup screen. If changes are made, they will take effect the next time the
projector is powered on.
‡‡
Default: The default startup screen.
‡‡
Neutral: Logo is not displayed on startup screen.
‡‡
User: Use stored picture from “Logo Capture” function.
Logo Capture
Select “Yes” to capture logo or “Cancel” to cancel logo capturing.
Background Color
Use this function to display a blue, red, green, grey color, none, or logo screen when no signal is available.
44 English
USING THE PROJECTOR
Setup reset menu
Reset OSD
Return the factory default settings for OSD menu settings.
Reset to Default
Return the factory default settings for Setup menu settings.
Network LAN menu (for Type 2)
Network Status
Display the network connection status (read-only).
MAC Address
Display the MAC address (read-only).
DHCP
Use this option to enable or disable the DHCP function.
‡‡
On: Projector will obtain an IP address automatically from your network.
‡‡
Off: To assign IP, subnet mask, gateway, and DNS configuration manually.
Note: Exiting OSD will automatically apply the entered values.
IP Address
Display the IP address.
Subnet Mask
Display subnet mask number.
Gateway
Display the default gateway of the network connected to the projector.
DNS
Display the DNS number.
How to use web browser to control your projector
1.
2.
3.
Note:
Turn “On” the DHCP option on projector to allow a DHCP server to automatically assign an IP address.
Open the web browser in your PC and type in the projector’s IP address (“Network > LAN > IP
Address”).
Enter the user name and password, and click “Login”.
The projector’s configuration web interface opens.
‡‡
The default user name and password is “admin”.
‡‡
The steps in this section is based on Windows 7 operating system.
English
45
USING THE PROJECTOR
Making a direct connection from your computer to the projector*
1.
2.
3.
Turn “Off” the DHCP option on the projector.
Configure the IP address, Subnet Mask, Gateway, and DNS on projector (“Network > LAN”).
Open Network and Sharing Center page on your PC, and assign the identical network parameters to
your PC as set on projector. Click “OK” to save the parameters.
4.
Open the web browser on your PC and type in to the URL field the IP address, assigned in step 3.
Then press “Enter” key.
Apply
Apply all values for LAN parameters.
Reset
Reset all values for LAN parameters.
Network control menu
Crestron
Use this function to select the network function (port: 41794).
For more information, please visit http://www.crestron.com and www.crestron.com/getroomview.
Extron
Use this function to select the network function (port: 2023).
PJ Link
Use this function to select the network function (port: 4352).
AMX Device Discovery
Use this function to select the network function (port: 9131).
Telnet
Use this function to select the network function (port: 23).
HTTP
Use this function to select the network function (port: 80).
46 English
USING THE PROJECTOR
Setup network control settings menu
LAN_RJ45 function
For simplicity and ease of operation, the projector provides diverse networking and remote management features.
The LAN / RJ45 function of the projector through a network, such as remotely manage: Power On / Off, brightness,
and contrast settings. Also, you can view the projector status information, such as: Video- Source, Sound-Mute, etc.
Projector
(Ethernet)
Wired LAN terminal functionalities
This projector can be controlled by using a PC (laptop) or other external device via LAN / RJ45 port and compatible
with Crestron / Extron / AMX (Device -Discovery) / PJLink.
‡‡
Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.
‡‡
Extron is a registered trademark of Extron Electronics, Inc. of the United States.
‡‡
AMX is a registered trademark of AMX LLC of the United States.
‡‡
PJLink applied for trademark and logo registration in Japan, the United States of America, and other
countries by JBMIA.
The projector is supported by the specified commands of the Crestron Electronics controller and related software,
for example RoomView®.
http://www.crestron.com/
This projector is compliant to support Extron device(s) for reference.
http://www.extron.com/
This projector is supported by AMX ( Device Discovery ).
http://www.amx.com/
This projector supports all commands of PJLink Class1 (Version 1.00).
http://pjlink.jbmia.or.jp/english/
For more detailed information about the various types of external devices which can be connected to the LAN /
RJ45 port and remote control the projector, as well as the supported commands for these external devices, please
contact the Support-Service directly.
English
47
USING THE PROJECTOR
LAN RJ45
1.
Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop).
HDMI 1 / MHL
HDMI 2
USB Power
Out (5V
VGA-IN 1 / YPbPr
VGA-IN 2 / YPbPr
S-VIDEO
Audio Out
Audio In
Audio In /Mic In
VGA-OUT / YPbPr
48 English
VIDEO
1.0A)
MOUSE /
SERVICE
RS-232C
RJ-45
2.
On the PC (Laptop), select Start > Control Panel > Network Connections.
3.
Right-click on the Local Area Connection, and select Property.
4.
In the Properties window, select the General tab, and select Internet Protocol (TCP / IP).
USING THE PROJECTOR
5.
Click “Properties”.
6.
Type in the IP address and Subnet mask, then press “OK”.
7.
8.
9.
Press the “Menu” button on the projector.
Open on projector Network > LAN.
Enter the following connection parameters:
±±
DHCP: Off
10.
11.
±±
IP Address: 192.168.0.100
±±
Subnet Mask: 255.255.255.0
±±
Gateway: 192.168.0.254
±±
DNS: 192.168.0.1
12.
Press “Enter” to confirm settings.
Open a web browser, for example Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher
installed.
In the Address bar, input the projector’s IP address: 192.168.0.100.
13.
Press “Enter”.
English
49
USING THE PROJECTOR
The projector is setup for remote management. The LAN / RJ45 function displays as follows:
Information page
Main page
Tool page
Contact IT helpdesk
50 English
USING THE PROJECTOR
RS232 by Telnet Function
There is alternative RS232 command control way, in projector so called “RS232 by TELNET” for LAN / RJ45
interface.
Quick Start-Guide for “RS232 by Telnet”
‡‡
Check and get the IP address on OSD of the projector.
‡‡
Make sure that the PC / laptop can access the web-page of the projector.
‡‡
Make sure that “Windows Firewall” setting is set disabled in case of “TELNET” function filtering out by
PC / laptop.
.
1.
Select Start > All Programs.> Accessories > Command Prompt.
2.
Input the command format as follows:
±±
telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)
±±
3.
(ttt.xxx.yyy.zzz: IP-Address of the projector)
If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key pressed, the
RS232 command will be workable.
Specification for “RS232 by TELNET”:
1.
2.
3.
4.
5.
Telnet: TCP.
Telnet port: 23 (for more detail, kindly please get contact with the service agent or team).
Telnet utility: Windows “TELNET.exe” (console mode).
Disconnection for RS232-by-Telnet control normally: Close
Windows Telnet utility directly after TELNET connection ready.
±±
Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload for
Telnet-Control application.
±±
Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232 command for
Telnet-Control.
±±
Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more than 200 (ms).
English
51
USING THE PROJECTOR
Info menu
Info menu
View the projector information as listed below:
52 English
‡‡
Regulatory
‡‡
Serial Number
‡‡
Current Input Source
‡‡
Resolution
‡‡
Refresh Rate
‡‡
Network Status
‡‡
IP Address
‡‡
Projector ID
‡‡
Remote Code
‡‡
Remote Code (Active)
‡‡
Display Mode
‡‡
Power mode(standby)
‡‡
Brightness Mode
‡‡
Filter Hours
‡‡
Lamp Hours
‡‡
FW Version
‡‡
Update
maintenance
Replacing the lamp
The projector automatically detects the lamp life. When the lamp life is nearing the end of use, a warning message
will appear on the screen.
Warning
Lamp Warning
Lamp life exceeded.
When you see this message, please contact your local reseller or service center to change the lamp as soon as
possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.
Warning: If ceiling mounted, please use caution when opening the lamp access panel. It is
recommended to wear safety glasses if changing the bulb when ceiling mounted. Caution must be used
to prevent any loose parts from falling out of projector.
Warning: Lamp compartment is hot! Allow it to cool down before changing lamp!
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The
bulb may shatter and cause injury if it is dropped.
English
53
MAINTENANCE
Replacing the lamp (continued)
2
3
4
5
6
1
Procedure:
1.
Switch off the power to the projector by pressing the " " button on the remote control or the projector
keypad.
2.
Allow the projector to cool down for at least 30 minutes.
3.
Disconnect the power cord.
4.
Unscrew the screw on the cover. 1
5.
Remove the cover. 2
6.
Unscrew the screw on the lamp module. 3
7.
Lift up the lamp handle. 4
8.
Remove the lamp cord. 5
9.
Remove the lamp module carefully. 6
10.
To replace the lamp module, reverse the previous steps.
11.
Turn on the projector and reset the lamp timer.
12.
Lamp Reset: (i) Press "Menu"  (ii) Select "Setup"  (iii) Select "Lamp Settings"  (iv) Select "Lamp
Reset"  (v) Select "Yes".
‡‡
‡‡
‡‡
The screw on the lamp cover and the lamp cannot be removed.
The projector cannot be turned on if the lamp cover has not been placed back on the projector.
Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean
the lamp module if it was accidentally touched.
Note:
54 English
MAINTENANCE
Installing and cleaning the dust filter
Installing the dust filter
Note: Dust filters are only required/supplied in the selected regions with excessive dust.
Cleaning the dust filter
We recommend you to clean the dust filter every three months. Clean it more often if the projector is used in a
dusty environment.
Procedure:
1.
Switch off the power to the projector by pressing the " " button on the remote control or the projector
keypad.
2.
Disconnect the power cord.
3.
Remove the dust filter carefully. 1
4.
Clean or replace the dust filter. 2
5.
To install the dust filter, reverse the previous steps.
2
1
English
55
additional information
Compatible resolutions
Digital compatibility
B0/Established
Timing
B0/Standard Timing
B0/Detail Timing
B1/Video Mode
B1/Detail Timing
720x400 @ 70Hz
SVGA:
Native timing:
640x480p @ 60Hz
720x480p @ 60Hz
640x480 @ 60Hz
800x600 @ 120Hz
XGA: 1024x768 @ 60Hz
720x480p @ 60Hz
1280x720p @ 60Hz
640x480 @ 67Hz
1024x768 @ 120Hz
WXGA: 1280x800 @ 60Hz;
1280x720 @ 60Hz
1280x720p @ 60Hz
1366x768 @ 60Hz
640x480 @ 72Hz
1280x800 @ 60Hz
1080P: 1920x1080 @ 60Hz
1920x1080i @ 60Hz
1920x1080i @ 50Hz
640x480 @ 75Hz
1280x1024 @ 60Hz
720(1440)x480i @ 60Hz
1920x1080p @ 60Hz
800x600 @ 56Hz
1680x1050 @ 60Hz
1920x1080p @ 60Hz
800x600 @ 60Hz
1280x720 @ 60Hz
720x576p @ 50Hz
800x600 @ 72Hz
1280x720 @ 120Hz
1280x720p @ 50Hz
800x600 @ 75Hz
1600x1200 @ 60Hz
1920x1080i @ 50Hz
832x624 @ 75Hz
XGA/WXGA:
720(1440)x576i @ 50Hz
1024x768 @ 60Hz
1440x900 @ 60Hz
1920x1080p @ 50Hz
1024x768 @ 70Hz
1024x768 @ 120Hz
1920x1080p @ 24Hz
1024x768 @ 75Hz
1280x800 @ 60Hz
1920x1080p @ 30Hz
1280x1024 @ 75Hz
1280x1024 @ 60Hz
1152x870 @ 75Hz
1680x1050 @ 60Hz
1280x720 @ 60Hz
1280x720 @ 120Hz
1600x1200 @ 60Hz
1080P:
1280x720 @ 60Hz
1280x800 @ 60Hz
1280x1024 @ 60Hz
1400x1050 @ 60Hz
1600x1200 @ 60Hz
1440x900 @ 60Hz
1280x720 @ 120Hz
1024x768 @ 120Hz
56 English
ADDITIONAL INFORMATION
Analog compatibility
B0/Established
Timing
B0/Standard Timing
B0/Detail Timing
720x400 @ 70Hz
SVGA:
Native timing:
640x480 @ 60Hz
800x600 @ 120Hz
XGA: 1024x768 @ 60Hz
640x480 @ 67Hz
1024x768 @ 120Hz
WXGA: 1280x800 @ 60Hz;
1280x720 @ 60Hz
640x480 @ 72Hz
1280x800 @ 60Hz
1080P: 1920x1080 @ 60Hz
640x480 @ 75Hz
1280x1024 @ 60Hz
800x600 @ 56Hz
1680x1050 @ 60Hz
800x600 @ 60Hz
1280x720 @ 60Hz
800x600 @ 72Hz
1280x720 @ 120Hz
800x600 @ 75Hz
1600x1200 @ 60Hz
832x624 @ 75Hz
XGA/WXGA:
1024x768 @ 60Hz
1440x900 @ 60Hz
1024x768 @ 70Hz
1024x768 @ 120Hz
1024x768 @ 75Hz
1280x800 @ 60Hz
1280x1024 @ 75Hz
1280x1024 @ 60Hz
1152x870 @ 75Hz
1680x1050 @ 60Hz
B1/Video Mode
B1/Detail Timing
1366x768 @ 60Hz
1280x720 @ 60Hz
1280x720 @ 120Hz
1600x1200 @ 60Hz
1080P:
1280x720 @ 60Hz
1280x800 @ 60Hz
1280x1024 @ 60Hz
1400x1050 @ 60Hz
1600x1200 @ 60Hz
1440x900 @ 60Hz
1280x720 @ 120Hz
1024x768 @ 120Hz
English
57
ADDITIONAL INFORMATION
True 3D video compatibility
Input timing
HDMI 1.4a 3D
Input
1280x720P @ 50Hz
Top - and - Bottom
1280x720P @ 60Hz
Top - and - Bottom
1280x720P @ 50Hz
Frame packing
1280x720P @ 60Hz
Frame packing
1920x1080i @ 50 Hz
Side- by-Side (Half)
1920x1080i @ 60 Hz
Side- by-Side (Half)
1920x1080P @ 24 Hz
Top - and- Bottom
1920x1080P @ 24 Hz
Frame packing
1920x1080i @ 50Hz
1920x1080i @ 60Hz
1280x720P @ 50Hz
Input resolution
1280x720P @ 60Hz
Side-by-Side(Half)
SBS mode is on
Top-and-Bottom
TAB mode is on
HQFS
3D format is Frame sequential
800 x 600 @ 60Hz
1024 x 768 @ 60Hz
1280 x 800 @ 60Hz
HDMI 1.3
1920x1080i @ 50Hz
1920x1080i @ 60Hz
1280x720P @ 50Hz
1280x720P @ 60Hz
800x600 @ 60Hz
1024x768 @ 60Hz
1280x800 @ 60Hz
480i
Note:
‡‡
‡‡
‡‡
58 English
If 3D input is 1080p@24hz, the DMD should replay with integral multiple with 3D mode.
Support NVIDIA 3DTV Play if there is no patent fee from Optoma. 1080i@25hz and 720p@50hz will
run in 100 hz; other 3D timing will run in 120hz.
1080p@24hz will run in 144Hz.
ADDITIONAL INFORMATION
Image size and projection distance
(XGA)
Diagonal
Length
Size of
(4:3)
Screen
Screen Size W x H
(m)
Projection Distance (D)
(inch)
(m)
Offset (Hd)
(feet)
Width
Height
Width
Height
Wide
Tele
Wide
Tele
(m)
(inch)
33
0.67
0.5
26.40
19.8
1.0
1.3
3.28
4.27
0.08
3.15
40
0.81
0.61
32.00
24
1.2
1.6
3.94
5.25
0.09
3.54
50
1.02
0.76
40.00
30
1.5
2.0
4.92
6.56
0.12
4.72
60
1.22
0.91
48.00
36
1.8
2.4
5.91
7.87
0.14
5.51
70
1.42
1.07
56.00
42
2.1
2.7
6.89
8.86
0.16
6.30
80
1.63
1.22
64.00
48
2.4
3.1
7.87
10.17
0.18
7.09
90
1.83
1.37
72.00
54
2.7
3.5
8.86
11.48
0.21
8.27
100
2.03
1.52
80.00
60
3.0
3.9
9.84
12.80
0.23
9.06
120
2.44
1.83
96.00
72
3.6
4.7
11.81
15.42
0.27
10.63
150
3.05
2.29
120.00
90
4.5
5.9
14.76
19.36
0.34
13.39
180
3.66
2.74
144.00
108
5.4
7.1
17.72
23.29
0.41
16.14
200
4.06
3.05
160.00
120
6.0
7.8
19.69
25.59
0.46
18.11
250
5.08
3.81
200.00
150
7.6
9.8
24.93
32.15
0.57
22.44
300
6.10
4.57
240.00
180
9.1
11.8
29.86
38.71
0.69
27.17
Note: Zoom ratio is 1.3x.
(WXGA)
Diagonal
Length
Size of
(4:3)
Screen
Screen Size W x H
(m)
Projection Distance (D)
(inch)
(m)
Offset (Hd)
(feet)
Width
Height
Width
Height
Wide
Tele
Wide
Tele
(m)
(inch)
39
0.84
0.53
33.07
20.67
1.0
1.3
3.28
4.27
0.06
2.36
40
0.86
0.54
33.92
21.2
1.0
1.3
3.28
4.27
0.07
2.76
50
1.08
0.67
42.40
26.5
1.3
1.7
4.27
5.58
0.09
3.54
60
1.29
0.81
50.88
31.8
1.5
2.0
4.92
6.56
0.10
3.94
70
1.51
0.94
59.36
37.1
1.8
2.3
5.91
7.55
0.12
4.72
80
1.72
1.08
67.84
42.4
2.0
2.7
6.56
8.86
0.13
5.12
90
1.94
1.21
76.32
47.7
2.3
3.0
7.55
9.84
0.15
5.91
100
2.15
1.35
84.80
53
2.6
3.3
8.53
10.83
0.16
6.30
120
2.58
1.62
101.76
63.6
3.1
4.0
10.17
13.12
0.20
7.87
150
3.23
2.02
127.20
79.5
3.8
5.0
12.47
16.40
0.25
9.84
180
3.88
2.42
152.64
95.4
4.6
6.0
15.09
19.69
0.30
11.81
200
4.31
2.69
169.60
106
5.1
6.7
16.73
21.98
0.34
13.39
250
5.38
3.37
212.00
132.5
6.4
8.3
21.00
27.23
0.41
16.14
300
6.46
4.04
254.40
159
7.7
10.0
25.26
32.81
0.50
19.69
Note: Zoom ratio is 1.3x.
English
59
ADDITIONAL INFORMATION
Top View
Screen
Screen (W)
Height
Projection Distance (D)
Screen
Side View
Offset (Hd)
Projection Distance (D)
60 English
Screen (H)
Dia
go
na
Width
l
ADDITIONAL INFORMATION
Projector dimensions and ceiling mount installation
1.
2.
To prevent damage to your projector, please use the Optoma ceiling mount.
If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to
the projector meet the following specifications:
‡‡
Screw type: M4*3
‡‡
Minimum screw length: 10mm
83.00
96.50
Lens
297.99
110.00
140.50
82.30
90.10
55.00
Unit: mm
Note: Please note that damage resulting from incorrect installation will void the warranty.
Warning:
‡‡
If you buy a ceiling mount from another company, please be sure to use the correct screw size.
Screw size will vary depending on the thickness of the mounting plate.
‡‡
Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.
‡‡
Avoid installing the projector near a heat source.
English
61
ADDITIONAL INFORMATION
IR remote control 1 codes
Key legend
Description
Key code
Power
Press to turn on / off the projector.
81
Freeze
Press to freeze the projector image.
8B
Aspect
Press to change aspect ratio of a displayed image.
98
AV mute
Press to turn off/ on projector built-in speaker
8A
Keystone+/up
Mute
Left/Vol-
Enter
Right/Vol+
‡‡
Press to adjust image distortion caused by tilting the projector.
‡‡
Press to navigate up.
Press to momentarily turn off / on the audio.
‡‡
Press to adjust to decrease the volume.
‡‡
Press to navigate left.
Confirm your item selection.
‡‡
Press to adjust to increase the volume.
‡‡
Press to navigate right.
Menu
Press to display or exit the on-screen display menus for projector.
Down/
Keystone-
‡‡
Press to adjust image distortion caused by tilting the projector.
‡‡
Press to navigate down.
3D
Press to manually select a 3D mode that matches your 3D content.
62 English
C6
92
C8
-C5 (for OSD)
-CA (for emulation
of USB mouse via
USB)
C9
88
C7
93
ADDITIONAL INFORMATION
Key legend
Description
Key code
HDMI
Press to choose HDMI source.
86
VGA
Press to choose VGA source.
8E
Video
Press to choose video source.
CE
Source
Press to select an input signal.
C3
Brightness
mode
Press to automatically adjust the picture brightness to give an
optimum contrast performance.
87
ReSync
Automatically synchronize the projector to the input source.
C4
English
63
ADDITIONAL INFORMATION
IR remote control 2 codes
Power
Switch
Freeze
L
R
Enter
Laser
Page+
V Keystone
-
-
+
1
PageVolume
+
2
3
Menu
3D
4
5
6
HDMI
VGA
Video
7
8
9
User1
User2
User3
0
Source
Key
code
Printing-key
definition
Power
81
Power on/off
Switch
3E
Switch
Display blank /
audio mute
8A
Freeze
8B
Mute
92
Key
Resync
Description
Press to turn on / off the projector.
Press to switch the USB mouse on / off.
Press to hide / unhide the screen picture and turn off / on
audio.
Freeze
Press to freeze the projector image.
Press to momentarily turn off / on the audio.
Mouse left click
L
CB
L
Use as mouse left click.
Mouse right click
R
CC
R
Use as mouse right click.
C6
Up arrow
C8
Left arrow
C9
Right arrow
C7
Down arrow
Four
directional select
keys
Enter
Page -
64 English
C5
Enter
CA
Enter
C2
Page-
Use
your selection.
to select items or make adjustments to
Confirm your item selection.
Press to page down.
ADDITIONAL INFORMATION
Key
code
Printing-key
definition
Laser
N/A
Laser
Use as laser pointer.
Page +
C1
Page+
Press to page up.
85
Keystone+
84
Keystone-
8C
Volume +
8F
Volume -
Key
V Keystone
-
+
Volume
-
+
Aspect ratio / 1
98
/1
Menu / 2
88
Menu/2
3D / 3
93
Description
Press to adjust image distortion caused by tilting the
projector.
Press to adjust to increase / decrease the volume.
‡‡
Press to change aspect ratio of a displayed image.
‡‡
Use as numeric keypad number "1".
‡‡
Press to display or exit the on-screen display menus
for projector.
‡‡
Use as numeric keypad number "2".
‡‡
Press to manually select a 3D mode that matches
your 3D content.
‡‡
Use as numeric keypad number "3".
‡‡
Press to choose HDMI source.
‡‡
Use as numeric keypad number "4".
‡‡
Press to choose VGA source.
‡‡
Use as numeric keypad number "5".
‡‡
Press to choose composite video source.
3D/3
HDMI / 4
86
HDMI/4
VGA / 5
D0
VGA/5
Video / 6
D1
Video/6
‡‡
Use as numeric keypad number "6".
D2
User 1/7
‡‡
User defined keys. Please see page 41 to setup.
D3
User 2/8
D4
User 3/9
‡‡
Use as numeric keypad numbers "7", "8", and "9"
accordingly.
Source
C3
Source
Brightness
mode / 0
96
Re-sync
C4
User1 / 7; User2 / 8;
User3 / 9
/0
Re-Sync
Press to select an input signal.
‡‡
Press to automatically adjust the picture brightness
to give an optimum contrast performance.
‡‡
Use as numeric keypad number "0".
Press to automatically synchronize the projector to the
input source.
English
65
ADDITIONAL INFORMATION
Troubleshooting
If you experience a problem with your projector, please refer to the following information. If a problem persists,
please contact your local reseller or service center.
Image problems
No image appears on-screen
‡‡
Ensure all the cables and power connections are correctly and securely connected as described in the
"Installation" section.
‡‡
Ensure the pins of connectors are not crooked or broken.
‡‡
Check if the projection lamp has been securely installed. Please refer to the "Replacing the Lamp"
section.
‡‡
Ensure that the "AV Mute" feature is not turned on.
Image is out of focus
‡‡
Adjust the Focus Ring on the projector lens.
‡‡
Make sure the projection screen is between the required distance from the projector. (Please refer to
pages 59-60).
The image is stretched when displaying 16:9 DVD title
‡‡
When you play anamorphic DVD or 16:9 DVD, the projector will show the best image in 16: 9 format
on projector side.
‡‡
If you play the LBX format DVD title, please change the format as LBX in projector OSD.
‡‡
If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD.
‡‡
Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player.
Image is too small or too large
‡‡
Adjust the zoom lever on the top of the projector.
‡‡
Move the projector closer to or further from the screen.
‡‡
Press "Menu" on the projector panel, go to "Display-->Aspect Ratio". Try the different settings.
Image has slanted sides:
‡‡
If possible, reposition the projector so that it is centered on the screen and below the bottom of the
screen.
‡‡
Use "Display-->Keystone" from the OSD to make an adjustment.
Image is reversed
‡‡
Select "Setup-->Projection" from the OSD and adjust the projection direction.
Blurry double image
‡‡
66 English
Press "3D" button and switch to "Off" to avoid normal 2D image is blurry double image.
ADDITIONAL INFORMATION
Two images, side-by-side format
‡‡
Press "3D" button and switch to "SBS" for input signal is HDMI 1.3 2D 1080i side-by-side.
Image does not display in 3D
‡‡
Check if the battery of 3D glasses is drained.
‡‡
Check if the 3D glasses is turned on.
‡‡
When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D" button and switch to "SBS".
Other problems
The projector stops responding to all controls
‡‡
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Lamp burns out or makes a popping sound
‡‡
When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the "Replacing the Lamp" section on pages 53-54.
Remote control problems
If the remote control does not work
‡‡
Check the operating angle of the remote control is pointed within ±15° to the IR receiver on the
projector.
‡‡
Make sure there are not any obstructions between the remote control and the projector. Move to within
6 m (20 ft) of the projector.
‡‡
Make sure batteries are inserted correctly.
‡‡
Replace batteries if they are exhausted.
English
67
ADDITIONAL INFORMATION
Warning indicators
When the warning indicators (see below) light up or flash, the projector will automatically shutdown:
‡‡
"LAMP" LED indicator is lit red and if "On/Standby" indicator flashes red.
‡‡
"TEMP" LED indicator is lit red and if "On/Standby" indicator flashes red. This indicates the projector
has overheated. Under normal conditions, the project can be switched back on.
‡‡
"TEMP" LED indicator flashes red and if "On/Standby" indicator flashes red.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or
flash, please contact your nearest service center for assistance.
LED lightning messages
Message
Power LED
Power LED
Temp-LED
Lamp-LED
(Red)
(Green or Blue)
(Red)
(Red)
Flashing
(0.5 sec off /
0.5 sec on)
Flashing
(0.5 sec off /
0.5 sec on)
Flashing
(0.5 sec off /
0.5 sec on)
Standby state
(Input power cord)
Steady light
Standby state (Burn
in mode)
Flashing
(0.5 sec off /
0.5 sec on)
Flashing
(0.5 sec off /
0.5 sec on)
Power on (Warming)
Burn in (Warming)
Flashing
Power on (Burn in
mode)
Flashing
(0.5 sec off /
0.5 sec on)
Power on and Lamp
lighting
Steady light
Power off (Cooling)
Flashing
(0.5 sec off /
0.5 sec light). Back
to red steady light
when cooling fan
turns off.
Burn in (Cooling)
Flashing
Flashing
(0.25 sec off /
0.25 sec on)
Quick Resume (100
secs)
‡‡
Error (Over temp.)
Flashing
Steady light
Error (Fan failure)
Flashing
Flashing
Error (Lamp failure)
Flashing
Power off:
Power Off
Power Off?
Press power key again.
68 English
Steady light
ADDITIONAL INFORMATION
‡‡
Lamp warning:
Warning
Lamp Warning
Lamp life exceeded.
‡‡
Temperature warning:
Warning
TEMPERATURE TOO HIGH
Please:
1. Make sure air in and outlets are not blocked.
2. Make sure the environment temperature is under 45 degree C.
If the problem persists in spite of the above.
Please contact a service center for repair.
‡‡
Fan failed:
Warning
FAN LOCKED
The projector will switch off automatically
Please contact a service center for repair.
‡‡
Out of display range:
HDMI
Out Of Range
‡‡
Power down warning:
Power Down
Power Down Timer Active
Power down in
sec.
‡‡
Security timer alarm:
Warning
Security Timer Alarm
Time Out in
sec.
English
69
ADDITIONAL INFORMATION
Specifications
Optical
Description
Native resolution
XGA/ WXGA
Lens
- Manual zoom and manual focus
Image size (diagonal)
22.9”~252” (overdrive to 300”)
Projection distance
1m ~ 10m (focus range) (overdrive to 12m)
Electrical
Description
- HDMI 1.4a
- HDMI 1.4a + MHL (v2.1)
Inputs
- VGA-IN (YPbPr / RGB)
- Audio 3.5mm
- S-Video
- VGA
Outputs
- Audio 3.5mm
- USB-A power
- RS232
Control
- USB mouse / service
Color reproduction
Scan rate
1073.4 Million color
- Horizontal scan rate: 15.375~91.146 KHz
- Vertical scan rate: 50~ 85 Hz (120Hz for 3D feature projector)
Built-in speaker
Yes, (2W/16W)
Power requirement
100 - 240V AC 50/60Hz
Input current
2.8-1.0 A
Mechanical
Installation orientation
Dimensions
Description
Front, Rear, Ceiling - Front, Rear - top
- 298 mm (W) x 230 mm (D) x 83 mm (H) (without feet)
- 298 mm (W) x 230 mm (D) x 96.5 mm (H) (with feet)
Weight
2.5 kg
Environmental conditions
Operating in 5 ~ 40°C , 10% to 85% humidity (non-condensing)
Note: All specifications are subject to change without notice.
70 English
ADDITIONAL INFORMATION
Optoma global offices
For service or support, please contact your local office.
USA
3178 Laurelview Ct.
Fremont, CA 94538, USA
www.optomausa.com
Canada
3178 Laurelview Ct.
Fremont, CA 94538, USA
www.optomausa.com
Latin America
Japan
888-289-6786
東京都足立区綾瀬3-25-18
510-897-8601
株式会社オーエス
services@optoma.com
コンタクトセンター:0120-380-495
info@os-worldwide.com
www.os-worldwide.com
Taiwan
888-289-6786
12F., No.213, Sec. 3, Beixin Rd.,
+886-2-8911-8600
510-897-8601
+886-2-8911-6550
services@optoma.com Xindian Dist., New Taipei City 231,
Taiwan, R.O.C.
services@optoma.com.tw
www.optoma.com.tw
asia.optoma.com
3178 Laurelview Ct.
Fremont, CA 94538, USA
www.optomausa.com
888-289-6786
Hong Kong
510-897-8601
services@optoma.com Unit A, 27/F Dragon Centre,
79 Wing Hong Street,
Cheung Sha Wan,
Europe
Kowloon, Hong Kong
42 Caxton Way, The Watford Business Park
Watford, Hertfordshire,
WD18 8QZ, UK
+44 (0) 1923 691 800
China
www.optoma.eu
+44 (0) 1923 691 888
5F, No. 1205, Kaixuan Rd.,
Service Tel : +44 (0)1923 691865
service@tsc-europe.com
Changning District
Shanghai, 200052, China
Benelux BV
Randstad 22-123
1316 BW Almere
The Netherlands
www.optoma.nl
France
Bâtiment E
81-83 avenue Edouard Vaillant
92100 Boulogne Billancourt, France
Spain
C/ José Hierro,36 Of. 1C
28522 Rivas VaciaMadrid,
Spain
Deutschland
Wiesenstrasse 21 W
D40549 Düsseldorf,
Germany
Scandinavia
Lerpeveien 25
3040 Drammen
Norway
+852-2396-8968
+852-2370-1222
www.optoma.com.hk
+86-21-62947376
+86-21-62947375
www.optoma.com.cn
+31 (0) 36 820 0252
+31 (0) 36 548 9052
+33 1 41 46 12 20
+33 1 41 46 94 35
savoptoma@optoma.fr
+34 91 499 06 06
+34 91 670 08 32
+49 (0) 211 506 6670
+49 (0) 211 506 66799
info@optoma.de
+47 32 98 89 90
+47 32 98 89 99
info@optoma.no
PO.BOX 9515
3038 Drammen
Norway
Korea
WOOMI TECH.CO.,LTD.
4F, Minu Bldg.33-14, Kangnam-Ku,
Seoul,135-815, KOREA
korea.optoma.com
+82+2+34430004
+82+2+34430005
English
71
www.optoma.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement