Optoma ZH606TST-W User Manual

Optoma ZH606TST-W User Manual
DLP® Projector
User manual
TABLE OF CONTENTS
SAFETY................................................................................................ 4
Important Safety Instruction....................................................................................................... 4
Cleaning the Lens...................................................................................................................... 5
Laser Radiation Safety Information............................................................................................ 6
Disclaimer................................................................................................................................... 6
Trademark Recognition.............................................................................................................. 6
FCC............................................................................................................................................ 7
Declaration of Conformity for EU countries................................................................................ 7
WEEE......................................................................................................................................... 7
INTRODUCTION................................................................................... 8
Package Overview..................................................................................................................... 8
Standard accessories................................................................................................................. 8
Optional accessories.................................................................................................................. 8
Product Overview....................................................................................................................... 9
Connections.............................................................................................................................. 10
Keypad...................................................................................................................................... 11
Remote control.......................................................................................................................... 12
SETUP AND INSTALLATION.............................................................. 13
Installing the projector............................................................................................................... 13
Connecting sources to the projector.......................................................................................... 15
Adjusting the projector image.................................................................................................... 17
Remote setup............................................................................................................................ 18
USING THE PROJECTOR................................................................... 20
Powering on / off the projector.................................................................................................. 20
Selecting an input source.......................................................................................................... 21
Menu navigation and features................................................................................................... 22
OSD Menu tree......................................................................................................................... 23
Display image settings menu.................................................................................................... 32
Display 3D menu....................................................................................................................... 35
Display aspect ratio menu......................................................................................................... 36
Display edge mask menu.......................................................................................................... 39
Display zoom menu................................................................................................................... 39
Display image shift menu.......................................................................................................... 39
Display geometric correction menu........................................................................................... 39
Audio mute menu...................................................................................................................... 40
Audio volume menu................................................................................................................... 40
Audio audio input menu............................................................................................................. 40
Audio audio / mic input function menu...................................................................................... 40
Setup projection menu.............................................................................................................. 41
Setup screen type menu........................................................................................................... 41
2
English
Setup power settings menu....................................................................................................... 41
Setup security menu.................................................................................................................. 42
Setup HDMI link settings menu................................................................................................. 42
Setup test pattern menu............................................................................................................ 42
Setup remote settings menu..................................................................................................... 43
Setup projector ID menu........................................................................................................... 43
Setup 12V trigger menu............................................................................................................ 43
Setup HDBaseT control menu................................................................................................... 43
Setup options menu.................................................................................................................. 44
Setup reset OSD menu............................................................................................................. 45
Network LAN menu................................................................................................................... 45
Network control menu............................................................................................................... 46
Setup network control settings menu........................................................................................ 47
Info menu.................................................................................................................................. 52
MAINTENANCE................................................................................... 53
Installing and cleaning the dust filter......................................................................................... 53
ADDITIONAL INFORMATION............................................................. 54
Compatible resolutions.............................................................................................................. 54
Image size and projection distance........................................................................................... 57
Projector dimensions and ceiling mount installation.................................................................. 59
IR remote codes........................................................................................................................ 60
Troubleshooting......................................................................................................................... 62
Warning indicators..................................................................................................................... 64
Specifications............................................................................................................................ 65
Optoma global offices................................................................................................................ 66
English
3
SAFETY
The lightning flash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Please follow all warnings, precautions and maintenance as recommended in this user’s guide.
To avoid electric shock, the unit and its peripherals must be properly grounded (earthed).
Important Safety Instruction
‡‡
‡‡
‡‡
‡‡
Do not stare into the beam, RG2.
As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015.
Notice is given to supervise children and to never allow them to stare into the projector beam at any
distance from the projector.
Notice is given to use caution when using the remote control for starting the projector while in front of
the projection lens.
Notice is given to the user to avoid the use of optical aids such as binoculars or telescopes inside the
beam.
‡‡
Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from
over heating, it is recommended to install the projector in a location that does not block ventilation.
As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the
projector in an enclosure such as a book case or a cabinet that restricts air flow.
‡‡
To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture. Do not
install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers
that emits heat.
‡‡
Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short
out parts that could result in fire or electric shock.
‡‡
Do not use under the following conditions:
±±
In extremely hot, cold or humid environments.
(i) Ensure that the ambient room temperature is within 5°C ~ 40°C
(ii) Relative humidity is 10% ~ 85%
4
English
±±
In areas susceptible to excessive dust and dirt.
±±
Near any appliance generating a strong magnetic field.
±±
In direct sunlight.
‡‡
Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be
(but not limited to):
±±
Unit has been dropped.
±±
Power supply cord or plug has been damaged.
±±
Liquid has been spilled on to the projector.
±±
Projector has been exposed to rain or moisture.
±±
Something has fallen in the projector or something is loose inside.
‡‡
Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the
projector may become damaged.
‡‡
Do not block the light coming out of the projector lens when in operation. The light will heat the object
and may melt, cause burns or start a fire.
‡‡
Please do not open or disassemble the projector as this may cause electric shock.
‡‡
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous
voltages or other hazards. Please call Optoma before you send the unit for repair.
‡‡
See projector enclosure for safety related markings.
‡‡
The unit should only be repaired by authorized service personnel.
‡‡
Only use attachments/accessories specified by the manufacturer.
‡‡
Do not look into straight into the projector lens during operation. The bright light may harm your eyes.
‡‡
This projector will detect the life of the light source itself.
‡‡
When switching the projector off, please ensure the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the projector to cool down.
‡‡
Turn off and unplug the power plug from the AC outlet before cleaning the product.
‡‡
Use a soft dry cloth with mild detergent to clean the display housing. Do not use abrasive cleaners,
waxes or solvents to clean the unit.
‡‡
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
‡‡
Do not setup the projector in places where it might be subjected to vibration or shock.
‡‡
Do not touch the lens with bare hands.
‡‡
Remove battery/batteries from remote control before storage. If the battery/batteries are left in the
remote for long periods, they may leak.
‡‡
Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it
can adversely affect the quality of the projector performance.
‡‡
Please follow the correct projector orientation installation as non standard installation may affect the
projector performance.
‡‡
Use a power strip and or surge protector. As power outages and brown-outs can KILL devices.
Cleaning the Lens
‡‡
Before cleaning the lens, be sure to turn off the projector and unplug the power cord to allow it to
completely cool down.
‡‡
Use a compressed air tank to remove the dust.
‡‡
Use a special cloth for cleaning lens and gently wipe the lens. Do not touch the lens with your fingers.
‡‡
Do not use alkaline/acid detergents or volatile solvents such as alcohol for cleaning lens. If the lens is
damaged due to the cleaning process, it is not covered by the warranty.
Warning: Do not use a spray containing flammable gases to remove dust or dirt from the lens. This
may cause a fire due to excessive heat inside the projector.
Warning: Do not clean the lens if the projector is warming up as this may cause the lens’ surface film
to peel off.
English
5
Warning: Do not wipe or tap the lens with a hard object.
Laser Radiation Safety Information
‡‡
This product is classified as CLASS 1 LASER PRODUCT - RISK GROUP 2 of IEC60825-1 : 2014 and
also complies with 21 CFR 1040.10 and 1040.11 as a Risk Group 2, LIP (Laser Illuminated Projector)
as defined in IEC 62471:5:Ed. 1.0. For more information see Laser Notice No. 57, dated May 8, 2019.
IEC 60825-1:2014 CLASS 1 LASER PRODUCT RISK GROUP 2
Complies with 21 CFR 1040.10 and 1040.11 except for conformance as a Risk Group 2
LIP as defined in IEC 62471-5:Ed. 1.0. For more information see Laser Notice No. 57,
dated May 8, 2019.
IEC 60825-1:2014 PRODUIT LASER DE CLASSE 1 GROUPE DE RISQUE 2
Conforme aux normes 21 CFR 1040.10 et 1040.11, à l'exception de la conformité en
tant que PIL du groupe de risque 2 définie dans la CEI 62471-5: Ed. 1,0. Pour plus
d'informations, voir l'avis au laser n ° 57 du 8 mai 2019.
IEC 60825-1:2014 1五◶‫૷⭘ݿ‬RG2ধ䳠ㅿ㍐
䲚ҼIEC 62471-5:Ed.1.0ѣᇐ㗟ⲺRG2 LIP ধ䳠ㅿ㍐ԛཌ, 㾷ㅜਾ21 CFR 1040.10ૂ
1040.11θᴪཐ⴮䰒䋽䁀θ䄁৹䯧2019ᒪ5ᴾ8ᰛⲺㅢ57㲕◶‫઀ޢݿ‬.
IEC 60825-1:2014 1㊱◶‫ݿ‬ӝ૷RG2ধ䲟ㅿ㓝
䲚ҼIEC 62471-5:Ed.1.0ѣᇐѿⲺRG2 LIP ধ䲟ㅿ㓝ԛཌ, 㾷ㅜਾ21 CFR 1040.10ૂ
1040.11θᴪཐ⴮ީ‫ؗ‬ᚥθ䈭৸䰻2019ᒪ5ᴾ8ᰛⲺㅢ57ਭ◶‫઀ޢݿ‬.
Failure to comply with the following could result in death or serious injury.
‡‡
This projector has built-in Class 4 laser module. Disassembly or modification is very dangerous and
should never be attempted.
‡‡
Any operation or adjustment not specifically instructed by the user’s guide creates the risk of
hazardous laser radiation exposure.
‡‡
Do not open or disassemble the projector as htis may cause damage by the exposure of laser
radiation.
‡‡
Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.
‡‡
When turning on the projector, make sure no one within projection range is looking at the lens.
‡‡
Without following the control, adjustment or operation procedure may cause damage by the exposure
of laser radiation.
‡‡
Adequate instructions for assembly, operation, and maintenance, including clear warnings concerning
precautions to avoid possible exposure to laser.
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright
laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced
without written consent of the author.
© Copyright 2019
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations
or warranties with respect to the contents hereof and specifically disclaims any implied warranties of
merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication
and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending
applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
DLP®, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a
trademark of Texas Instruments.
6
English
MHL, Mobile High-Definition Link and the MHL Logo are trademarks or registered trademarks of MHL Licensing,
LLC.
All other product names used in this manual are the properties of their respective owners and are Acknowledged.
FCC
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be determined by turning the device off and on is
encouraged to try to correct the interference by one or more of the following measures:
‡‡
Reorient or relocate the receiving antenna.
‡‡
Increase the separation between the device and receiver.
‡‡
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
‡‡
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC
regulations.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is
granted by the Federal Communications Commission, to operate this projector.
Operation Conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque à l'intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
‡‡
EMC Directive 2014/30/EU (including amendments)
‡‡
Low Voltage Directive 2014/35/EU
‡‡
RED 2014/53/EU (if product has RF function)
WEEE
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure
utmost protection of the global environment, please recycle it.
English
7
INTRODUCTION
Package Overview
Carefully unpack and verify that you have the items listed below under standard accessories. Some of the items
under optional accessories may not be available depending on the model, specification and your region of
purchase. Please check with your place of purchase. Some accessories may vary from region to region.
The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.
Standard accessories
On
Off
Geometric
Correction
PIP/PBP
F1
F2
 Warranty Card*
 Basic User Manual
 Paper UM
AV Mute
Mode
ENTER
Info.
Source
Re-Sync
F3
Volume
D Zoom
Menu
Format Freeze
Remote
ID
All
VGA S-Video HDMI1 HDMI2
1
2
HDBaseT Video
4
BNC
7
Projector
5
3
DVI
HDMI3
6
YPbPr DisplayPort 3D
8
9
0
Remote control
Power lead
Documentation
Note:
‡‡
‡‡
The remote control is shipped with the battery.
* For European warranty Information, please visit www.optoma.com.
Optional accessories
Lens cap
CD user manual
Carry bag
Note:
‡‡
8
English
Optional accessories vary depending on model, specification and region.
VGA cable
INTRODUCTION
Product Overview
1
4
2
5
6
3
7
8
11
8
13
10
9
12
8
Note:
‡‡
‡‡
Do not block projector intake and exhaust vents.
When operating the projector in an enclosed space, allow at least 30 cm clearance around the intake
and exhaust vents.
No
Item
No
Item
1.
IR Receivers
8.
Tilt-Adjustment Feet
2.
Keypad
9.
Kensington™ Lock Port
3.
Lens Shift Dial
10. Input / Output
4.
Ventilation (inlet)
11. Power Socket
5.
Zoom Lever
12. Security Bar
6.
Focus Ring
13. Lens
7.
Ventilation (outlet)
English
9
INTRODUCTION
Connections
Type 1 WUXGA
1
17
2
16
3
4a
15
5
14
6
13
7
9
8
12
11
10
Type 2 1080P
1
17
No
10 English
2
3
15
4b
7
14
Item
13
9
8
12
11
10
No
Item
1.
HDMI2 Connector
10. Kensington
2.
HDMI1 / MHL Connector
11. AUDIO-OUT Connector
3.
USB POWER OUT (5V 1.5A)
Connector
12. AUDIO-IN 2 Connector
4.
a: VGA-IN 1 Connector
b: VGA-IN Connector
13. VGA-OUT Connector
5.
VGA-IN 2 Connector
14. RS232
6.
S-VIDEO Connector
15. RJ-45 Connector
7.
VIDEO Connector
16. HDBaseT Connector
8.
AUDIO-IN 1 / MIC-IN Connector
17. Power Socket
9.
12V OUT Connector
TM
Lock Port
INTRODUCTION
Keypad
1
No
Item
2
3
10
9
4
5
8
6
7
No
Item
1.
Lamp LED
6.
Temp LED
2.
Power and Power LED
7.
Re-Sync
3.
Menu
8.
Four Directional Select Keys
4.
Keystone Correction
9.
Source
5.
Enter
10. Information
English
11
INTRODUCTION
Remote control
On
Off
1
34
Geometric
2
Correction
PIP/PBP
33
F1
F2
32
3
AV Mute
Mode
4
31
5
ENTER
30
6
7
29
Info.
Source
Re-Sync
28
F3
8
Volume
9
D Zoom
10
27
Menu
11
12
13
14
15
Format Freeze
All
VGA S-Video HDMI1 HDMI2
1
2
3
HDBaseT Video
4
BNC
17
Item
DVI
5
HDMI3
6
8
18
9
19
0
20
25
24
23
YPbPr DisplayPort 3D
7
16
No
26
Remote
ID
22
21
No
Item
1.
Power on
18. YPbPr (not supported)
2.
Geometric Correction
19. Numeric keypad (0-9)
3.
Function button (F1) (Assignable)
20. Display port (not supported)
4.
Mode
21. 3D
5.
Four directional select keys
22. DVI (not supported)
6.
Information
23. HDMI3 (not supported)
7.
Function button (F3) (Assignable)
24. HDMI1
8.
Source
25. HDMI2
9.
Menu
26. Remote ID / Remote all
10. Volume - / +
27. Digital Zoom - / +
11. Freeze
28. Re-sync
12. Format (Aspect Ratio)
29. Laser
13. VGA
30. Enter
14. S-Video
31. AV Mute
15. HDBase-T
32. Function button (F2) (Assignable)
16. Video
33. PIP/PBP (not supported)
17. BNC (not supported)
34. Power off
Note: Some keys may have no function for models that do not support these features.
12 English
SETUP AND INSTALLATION
Installing the projector
Your projector is designed to be installed in one of four possible positions.
Your room layout or personal preference will dictate which installation location you select. Take into consideration
the size and position of your screen, the location of a suitable power outlet, as well as the location and distance
between the projector and the rest of your equipment.
Table mount front
Ceiling mount front
Table mount rear
Ceiling mount rear
Projector should be placed flat on a surface and 90 degrees / perpendicular to the screen.
‡‡
How to determine projector location for a given screen size, please refer to distance table on pages
57-58.
‡‡
How to determine screen size for a given distance, please refer to distance table on pages 57-58.
Note: The further away the projector is placed from the screen the projected image size increases and vertical
offset also increases proportionally.
English
13
SETUP AND INSTALLATION
Projector installation notice
‡‡
360 degree free orientation operation.
Note: The brightness will vary when the projector is installed within the range highlighted.
The fan will default to “High altitude mode” when the projector is installed within the range highlighted.
45°
45°
225°~315°
45° 45°
‡‡
Allow at least 30 cm clearance around the exhaust vent.
Minimum 100mm
(3.94 inches)
Minimum 300mm
(11.81 inches)
Minimum 300mm
(11.81 inches)
Minimum 100mm
(3.94 inches)
14 English
‡‡
Ensure that the intake vents do not recycle hot air from the exhaust vent.
‡‡
When operating the projector in an enclosed space, ensure that the surrounding air temperature within
the enclosure does not exceed operation temperature while the projector is running, and the air intake
and exhaust vents are unobstructed.
‡‡
All enclosures should pass a certified thermal evaluation to ensure that the projector does not recycle
exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the
acceptable operation temperature range.
SETUP AND INSTALLATION
Connecting sources to the projector
Type 1 WUXGA
7
6
5
9
4
8
2
1
10
3
11
12
16
13
18
17
15
14
English
15
SETUP AND INSTALLATION
Type 2 1080P
6
5
9
4
8
2
1
10
3
11
12
16
13
18
No
16 English
15
Item
14
No
Item
1.
HDMI Cable
10. Audio In Cable
2.
MHL Cable
11. 12V DC Jack
3.
HDMI Dongle
12. Microphone Cable
4.
USB Power Cable
13. Audio Out Cable
5.
VGA In Cable
14. VGA Out Cable
6.
RCA Component Cable
15. RS232 Cable
7.
S-Video Cable
16. RJ-45 Cable
8.
Video Cable
17. RJ-45 Cable (Cat-5e/6 Cables)
9.
Audio In Cable
18. Power Cord
SETUP AND INSTALLATION
Adjusting the projector image
Image height
The projector is equipped with elevator feet for adjusting the image height.
1.
Locate the adjustable foot you wish to adjust on the underside of the projector.
2.
Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
Lens shift, focus, and zoom
‡‡
To adjust the image position, turn the lens shift dial clockwise or counterclockwise to adjust the
position of the projected image vertically.
‡‡
To adjust the focus, turn the focus ring clockwise or counterclockwise until the image is sharp and
legible.
‡‡
To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease
the projected image size.
Zoom Lever
Lens Shift Dial
Focus Ring
English
17
SETUP AND INSTALLATION
Remote setup
Installing / replacing the batteries
Two AAA size batteries are supplied for the remote control.
1.
2.
3.
Remove the battery cover on the back of the remote control.
Insert AAA batteries in the battery compartment as illustrated.
Replace back cover on remote control.
Note: Replace only with the same or equivalent type batteries.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
18 English
‡‡
Do not mix batteries of different types. Different types of batteries have different characteristics.
‡‡
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or
cause chemical leakage in old batteries.
‡‡
Remove batteries as soon as the are depleted. Chemicals that leak from batteries that come in contact
with skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.
‡‡
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
‡‡
If you will not be using the remote control for an extended period of time, remove the batteries.
‡‡
When you dispose of the batteries, you must obey the law in the relative area or country.
SETUP AND INSTALLATION
Effective range
Infra-Red (IR) remote control sensor is located on the top and front sides of the projector. Ensure to hold the
remote control at an angle within 30 degrees perpendicular to the projector’s IR remote control sensor to function
correctly. The distance between the remote control and the sensor should not be longer than 6 meters (19.7 feet)
when holding in an angle ±15° and not longer than 8 meters (26.2 feet) when aiming the sensor at 0°.
‡‡
Make sure that there are no obstacles between the remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
‡‡
Make sure the IR transmitter of the remote control is not being shined by sunlight or fluorescent lamps
directly.
‡‡
Please keep the remote controller away from fluorescent lamps for over 2 m or the remote controller
might become malfunction.
‡‡
If the remote control is close to Inverter-Type fluorescent lamps, it might become ineffective from time
to time.
‡‡
If the remote control and the projector are within a very short distance, the remote control might
become ineffective.
‡‡
When you aim at the screen, the effective distance is less than 5 m from the remote control to the
screen and reflecting the IR beams back to the projector. However, the effective range might change
according to screens.
7
8
BNC
9
0
YPbPr DisplayPort 3D
4
5
6
HDBaseT Video
1
DVI
2
HDMI3
3
VGA S-Video HDMI1 HDMI2
ID
Format Freeze
All
Remote
Menu
Volume
D Zoom
F3
Source
Re-Sync
Info.
ENTER
Mode
AV Mute
F2
F1
PIP/PBP
Correction
Geometric
On
Off
Approx. ±15°
Approx. ±15°
On
Off
ic
etr n
om tio
c
Ge
rre
Co
F1
e
od
M
/P
PIP
BP
F2
AV
TE
e
urc
.
R
ute
M
EN
fo
So
In
e
m
lu
Vo
F3
-S
Re
c
yn
u
om
I1
3
9
D
t3
Por
I3
M
play
HD
Dis
6
I2
M
I
HD
8
r
DV
bP
YP
5
M
ote ll
m
A
Re
HD
ID
eo
7
eo
C
Vid
BN
2
eT
4
id
Bas
S-V
HD
1
eze
A
Fre
VG
Zo
en
at
D
M
rm
Fo
0
English
19
USING THE PROJECTOR
Powering on / off the projector
or
On
Off
Geometric
Correction
PIP/PBP
F1
F2
AV Mute
Mode
ENTER
Info.
Source
Re-Sync
F3
Volume
D Zoom
Menu
Format Freeze
Remote
ID
All
VGA S-Video HDMI1 HDMI2
Lens cap
1
2
HDBaseT Video
4
BNC
5
3
DVI
HDMI3
6
YPbPr DisplayPort 3D
Powering on
7
8
9
0
1.
Remove the lens cap.
2.
Securely connect the power lead and signal/source cable. When connected, the Power LED will turn
red.
3.
Turn on the projector by pressing the button on the projector keypad or remote control.
4.
A start up screen will display in approximately 10 seconds and the Power LED will be flashing blue or
flashing green.
Note: The first time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1.
Turn off the projector by pressing the button on the projector keypad or the
control.
2.
The following message will be displayed:
button on the remote
Power Off
Press power key again.
3.
4.
5.
Press the or button again to confirm, otherwise the message will disappear after 15 seconds.
When you press the or button for the second time, the projector will shut down.
When the Power turns solid red, this indicates the projector has entered standby mode. If you wish
to turn the projector back on, you must wait until the cooling cycle has finished and the projector has
entered standby mode. When the projector is in standby mode, simply press the button again to
turn on the projector.
Disconnect the power lead from the electrical outlet and the projector.
Note: It is not recommended that the projector is turned on immediately, right after a power off procedure.
20 English
USING THE PROJECTOR
On
Off
Geometric
Selecting an input source
Correction
PIP/PBP
F1
F2
AV Mute
Mode
Turn on the connected source that you want to display on the screen, such as computer, notebook, video player,
etc. The projector will automatically detect the source. If multiple sources are connected, press the
button on the
ENTER input.
projector keypad or the Source button on the remote control to select the desired
Info.
or
Source
Re-Sync
F3
Volume
D Zoom
Menu
Format Freeze
Remote
ID
All
VGA S-Video HDMI1 HDMI2
1
2
HDBaseT Video
4
BNC
7
5
3
DVI
HDMI3
6
YPbPr DisplayPort 3D
8
9
0
Lens cap
English
21
USING THE PROJECTOR
Menu navigation and features
The projector has multilingual on-screen display menus that allow you to make image adjustments and change a
variety of settings. The projector will automatically detect the source.
button on the projector keypad or the Menu button on the remote
1.
To open the OSD menu, press the
control.
2.
When OSD is displayed, use pq keys to select any item in the main menu. While making a selection
on a particular page, press the
button on the projector keypad or the Enter button on the remote
control to enter sub menu.
3.
Use tu keys to select the desired item in the sub menu and then press the
view further settings. Adjust the settings by using tu keys.
4.
Select the next item to be adjusted in the sub menu and adjust as described above.
5.
Press press the
6.
To exit, press the or Menu button again. The OSD menu will close and the projector will
automatically save the new settings.
or Enter button to
or Enter button to confirm, and the screen will return to the main menu.
Settings
Sub Menu
Display
Image Settings
3D
Main Menu
Aspect Ratio
Edge Mask
Zoom
Image Shift
Geometric Correction
Select
Exit
Navigation guide
22 English
Enter
USING THE PROJECTOR
OSD Menu tree
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Presentation
Bright
HDR
Cinema
Game
Display Mode
sRGB
DICOM SIM.
User
3D
Off [Default]
Blackboard
Light Yellow
Wall Color
Light Green
Light Blue
Pink
Gray
HDR
Display
Image Settings
Dynamic Range
Off
Auto [Default]
Bright
HDR Picture
Mode
Standard [Default]
Film
Detail
Brightness
-50 ~ 50
Contrast
-50 ~ 50
Sharpness
1 ~ 15
Color
-50 ~ 50
Tint
-50 ~ 50
Film
Video
Graphics
Gamma
Standard(2.2)
1.8
2.0
2.4
2.6
Color Settings
BrilliantColorTM
1 ~ 10
English
23
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Warm
Standard
Color
Temperature
Cool
Cold
Red [Default]
Green
Blue
Color
Cyan
Yellow
Magenta
Color Matching
White(*)
Hue / R(*)
-50 ~ 50 [Default: 0]
Saturation / G(*)
-50 ~ 50 [Default: 0]
Gain / B(*)
-50 ~ 50 [Default: 0]
Reset
Cancel [Default]
Yes
Exit
Color Settings
Display
Image Settings
RGB Gain/Bias
Red Gain
-50 ~ 50
Green Gain
-50 ~ 50
Blue Gain
-50 ~ 50
Red Bias
-50 ~ 50
Green Bias
-50 ~ 50
Blue Bias
-50 ~ 50
Reset
Cancel [Default]
Yes
Exit
Color Space [Not
HDMI Input]
Auto [Default]
RGB
YUV
Auto [Default]
Color Space
[HDMI Input]
RGB(0~255)
RGB(16~235)
YUV
White Level
0 ~ 31
Black Level
-5 ~ 5
IRE
Automatic
Signal
24 English
0
7.5
Off
On [Default]
Frequency
-10 ~ 10 (depends on signal)
[Default: 0]
Phase
0~31 (depends on signal)
[Default: 0]
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
H. Position
-5 ~ 5 (depends on signal)
[Default: 0]
V. Position
-5 ~ 5 (depends on signal)
[Default: 0]
Signal
DynamicBlack
Image Settings
Brightness Mode
Power
(Power = 100%/ 95%/ 90%/ 85%/
80%/ 75%/ 70%/ 65%/ 60%/ 55%/
50%)
Reset
3D Mode
3D Tech
Off
On [Default]
DLP-Link [Default]
3D Sync
3D [Default]
3D  2D
L
R
3D
Auto [Default]
3D Format
SBS
Top and Bottom
Frame Sequential
Display
3D Sync Invert
Reset
On
Off [Default]
Cancel
Yes
4:3
16:9
16:10
Aspect Ratio
Note: For WUXGA model only.
LBX
Native
Auto
Edge Mask
0 ~ 10 [Default: 0]
Zoom
-5 ~ 25 [Default: 0]
Image Shift
H
-100 ~ 100 [Default: 0]
V
-100 ~ 100 [Default: 0]
Four Corners
Geometric
Correction
H Keystone
-30 ~ 30 [Default: 0]
V Keystone
-30 ~ 30 [Default: 0]
Auto Keystone
Off
On [Default]
Reset
Audio
Mute
Volume
Off [Default]
On
0 ~ 10 [Default: 5]
English
25
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Audio 1
Audio 2
HDMI1/MHL
Default [Default]
Audio 1
Audio 2
HDMI2
Default [Default]
Audio 1
HDBaseT
[Only for
HDBaseT model]
Audio Input
Audio
Audio 2
Default [Default]
VGA
[Only for
non-HDBaseT
model]
Audio 1
VGA 1
[Only for
HDBaseT model]
Audio 1
VGA 2
[Only for
HDBaseT model]
Audio 1
S-Video
[Only for
HDBaseT model]
Audio 1
Audio 2
Audio 2
Audio 2
Audio 2
Audio 1
Video
Audio 2
Audio Input [Default]
Audio / Mic
Input Function
Mic
Front
[Default]
Rear
Projection
Ceiling-top
Rear-top
Screen Type
[Only for
WUXGA model]
16:9
16:10 [Default]
Off [Default]
Direct Power On
Setup
On
Off [Default]
Signal Power On
On
Auto Power Off
(min.)
Power Settings
26 English
Sleep Timer
(min.)
0 ~ 180 (5 min increments)
[Default: 20]
0 ~ 990 (30 min increments)
[Default: 0]
Always On
No [Default]
Yes
Power Mode
(Standby)
Active
USB Power
(Standby)
Off [Default]
Eco [Default]
On
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Off
Security
On
Month
Security
Security Timer
Day
Hour
Change
Password
HDMI Link
Inclusive of TV
HDMI Link
Settings
[Default: 1234]
Off [Default]
On
No [Default]
Yes
Mutual [Default]
Power On Link
PJ → Device
Device → PJ
Power Off Link
Off [Default]
On
Green Grid
Magenta Grid
Test Pattern
White Grid
White
Off
Setup
IR Function
Remote Code
On [Default]
Off
00~99
Test Pattern
Brightness
Contrast
Sleep Timer
F1
Color Matching
Color Temp
Remote
Settings
[depends on
remote]
Gamma
Projection
MHL
Test Pattern
Brightness
Contrast
Sleep Timer
F2
Color Matching
Color Temp
Gamma
Projection
MHL
English
27
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Test Pattern
Brightness
Contrast
Remote
Settings
[depends on
remote]
Sleep Timer
F3
Color Matching
Color Temp
Gamma
Projection
MHL
Projector ID
00 ~ 99
On
12V Trigger
Off
Ethernet
HDBaseT
Control
RS232
HDBaseT Mode
On
Off [Default]
On
Off [Default]
Auto
HDBaseT [Default]
English [Default]
Deutsch
Français
Italiano
Español
Setup
Português
Polski
Nederlands
Svenska
Norsk/Dansk
Suomi
ελληνικά
繁體中文
Options
Language
簡体中文
日本語
한국어
Русский
Magyar
Čeština
ไทย
Türkçe
Tiếng Việt
Bahasa Indonesia
Română
Slovenčina
28 English
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
CC1
Closed
Captioning
CC2
Off [Default]
Top left
Top right
Menu Location
Center
[Default]
Bottom left
Menu Settings
Bottom right
Off
Menu Timer
5sec
10sec [Default]
Off [Default]
Auto Source
On
HDMI1/MHL
HDMI2
HDBaseT
VGA
Input Source
VGA 1
VGA 2
S-Video
Setup
Video
Options
HDMI1/MHL
HDMI2
Input Name
Display Mode
Lock
Custom
Default [Default]
Custom
HDBaseT
[Only for
HDBaseT model]
Default [Default]
VGA
[Only for
non-HDBaseT
model]
Default [Default]
VGA 1
[Only for
HDBaseT model]
Default [Default]
VGA 2
[Only for
HDBaseT model]
Default [Default]
S-Video
[Only for
HDBaseT model]
Default [Default]
Video
High Altitude
Default [Default]
Custom
Custom
Custom
Custom
Custom
Default [Default]
Custom
Off [Default]
On
Off [Default]
On
English
29
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Keypad Lock
Information Hide
Sub Menu 3
Sub Menu 4
Values
Off [Default]
On
Off [Default]
On
Default [Default]
Logo
Neutral
User
Options
None [Default for Video/Pro-AV model]
Note: “None” means black color
background.
Setup
Background
Color
Blue [Default for data model]
Red
Green
Gray
Logo
Reset OSD
Reset
Reset to Default
Yes
Cancel [Default]
Yes
Network Status
(read only)
MAC Address
(read only)
DHCP
LAN
Cancel [Default]
Off [Default]
On
IP Address
192.168.0.100 [Default]
Subnet Mask
255.255.255.0 [Default]
Gateway
192.168.0.254 [Default]
DNS
192.168.0.51 [Default]
Reset
Off
Crestron
On [Default]
Note: Port 41794
Off
Network
Extron
On [Default]
Note: Port 2023
Off
PJ Link
Control
AMX Device
Discovery
On [Default]
Note: Port 4352
Off
On [Default]
Note: Port 9131
Off
Telnet
On [Default]
Note: Port 23
Off
HTTP
30 English
On [Default]
Note: Port 80
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Regulatory
Serial Number
Source
Resolution
00x00
Refresh Rate
0.00Hz
Display Mode
Info
Remote Code
00 ~ 99
Remote
Code(Active)
00 ~ 99
Power Mode
(Standby)
Light Source
Hours
0 hr
Network Status
IP Address
Projector ID
00 ~ 99
Brightness
Mode
System
FW Version
LAN
MCU
English
31
USING THE PROJECTOR
Display menu
Display image settings menu
Display Mode
There are many factory presets optimized for various types of images.
‡‡
Presentation: This mode is suitable for showing in front of public in connection to the PC.
‡‡
Bright: Maximum brightness from PC input.
‡‡
HDR: Decodes and displays High Dynamic Range (HDR) content for the deepest blacks, brightest
whites, and vivid cinematic color using REC.2020 color gamut. This mode will be automatically
enabled if HDR is set to ON (and HDR Content is sent to projector – 4K UHD Blu-ray, 1080p/4K UHD
HDR Games, 4K UHD Streaming Video). While HDR mode is active, other display modes (Cinema,
Reference, etc.) cannot be selected as HDR delivers color that is highly accurate, exceeding the color
performance of the other display modes.
‡‡
Cinema: Provides the best colors for watching movies.
‡‡
Game: Select this mode to increase the brightness and response time level for enjoying video games.
‡‡
sRGB: Standardized accurate color.
‡‡
DICOM SIM.: This mode can project a monochrome medical image such as an X ray radiography,
MRI, etc.
‡‡
User: Memorize user’s settings.
‡‡
3D: To experience the 3D effect, you need to have 3D glasses, make sure your PC/portable device
has a 120 Hz signal output quad buffered graphics card and have a 3D Player installed.
Wall Color
Use this function to obtain an optimized screen image according to the wall color. Select between off, blackboard,
light yellow, light green, light blue, pink, and gray.
Dynamic Range
Configure the High Dynamic Range (HDR) setting and its effect when displaying video from 4K Blu-ray players and
streaming devices.
Note: HDMI2 and VGA do not support Dynamic Range.
 HDR
‡‡ Off: Turn off HDR Processing. When set to Off, the projector will NOT decode HDR content.
‡‡ Auto: Auto detect HDR signal.
 HDR Picture Mode
‡‡ Bright: Choose this mode for brighter more saturated colors.
‡‡ Standard: Choose this mode for natural looking colors with a balance of warm and cool tones.
‡‡ Film: Choose this mode for improved detail and image sharpness.
‡‡ Details: The signal comes from OETF conversion to achieve the best color matching.
Brightness
Adjust the brightness of the image.
Contrast
The contrast controls the degree of difference between the lightest and darkest parts of the picture.
Sharpness
Adjust the sharpness of the image.
32 English
USING THE PROJECTOR
Color
Adjust a video image from black and white to fully saturated color.
Tint
Adjust the color balance of red and green.
Gamma
Set up gamma curve type. After the initial setup and fine tuning is completed, utilize the Gamma Adjustment steps
to optimize your image output.
‡‡
Film: For home theater.
‡‡
Video: For video or TV source.
‡‡
Graphics: For PC / Photo source.
‡‡
Standard(2.2): For standardized setting.
‡‡
1.8 / 2.0 / 2.4 / 2.6: For specific PC / Photo source.
‡‡
These options are only available if the 3D mode function is disabled, the Wall Color setting is not set
to Blackboard, and the Display Mode setting is not set to DICOM SIM. or HDR.
‡‡
If the Display Mode setting is set to HDR, user can only select HDR for Gamma setting.
‡‡
In 3D mode, user can only select 3D for Gamma setting.
‡‡
If the Wall Color setting is set to Blackboard, user can only select Blackboard for Gamma setting.
‡‡
If the Display Mode setting is set to DICOM SIM., user can only select DICOM SIM. for Gamma
setting.
Note:
Color Settings
Configure the color settings.
‡‡
BrilliantColorTM: This adjustable item utilizes a new color-processing algorithm and enhancements to
enable higher brightness while providing true, more vibrant colors in picture.
‡‡
Color Temperature: Select a color temperature from Warm, Standard, Cool, or Cold.
‡‡
Color Matching: Select the following options:
±±
Color: Adjust the red, green, black, cyan, yellow, magenta, and white level of the image.
‡‡
±±
Hue / R(red)*: Adjust the color balance of red and green.
Note: *If the Color setting is set to White, you can adjust the red color setting.
±±
Saturation / G(green)*: Adjust a video image from black and white to fully saturated color.
Note: *If the Color setting is set to White, you can adjust the green color setting.
±±
Gain / B(blue)*: Adjust the image brightness.
Note: *If the Color setting is set to White, you can adjust the blue color setting.
±±
Reset: Return the factory default settings for color matching.
±±
Exit: Exit the “Color Matching” menu.
RGB Gain/Bias: This settings allows to configure the brightness (gain) and contrast (bias) of an
image.
±±
Reset: Return the factory default settings for RGB gain/bias.
±±
‡‡
Exit: Exit the “RGB Gain/Bias” menu.
Color Space (non-HDMI input only): Select an appropriate color matrix type from the following:
AUTO, RGB, or YUV.
English
33
USING THE PROJECTOR
‡‡
Color Space (HDMI input only): select an appropriate color matrix type from the following: Auto,
RGB(0-255), RGB(16-235), and YUV.
‡‡
White Level: Allow user to adjust White Level when inputting Video signals.
Note: White level can only be adjusted for Video/S-Video input sources.
‡‡
Black Level: Allow user to adjust Black Level when inputting Video signals.
Note: Black level can only be adjusted for Video/S-Video input sources.
‡‡
IRE: Allow user to adjust IRE value when inputting Video signals.
Note:
‡‡
IRE is only available with NTSC video format.
‡‡
IRE can only be adjusted for Video/S-Video input sources.
Signal
Adjust the signal options.
‡‡
Automatic: Configure automatically the signal (the frequency and phase items are grayed out). If
automatic is disabled, the frequency and phase items will appear for tuning and saving the settings.
‡‡
Frequency: Change the display data frequency to match the frequency of your computer’s graphic
card. Use this function only if the image appears to flicker vertically.
‡‡
Phase: Synchronize the signal timing of the display with the graphic card. If the image appears to be
unstable or flickers, use this function to correct it.
‡‡
H. Position: Adjust the horizontal positioning of the image.
‡‡
V. Position: Adjust the vertical positioning of the image.
Note: This menu is only available if the input source is RGB/Component.
Brightness Mode
Adjust the brightness mode settings.
‡‡
DynamicBlack: Use to automatically adjust the picture brightness in order to give optimum contrast
performance.
‡‡
Power: Choose the power percentage for brightness mode.
Reset
Return the factory default settings for color settings.
34 English
USING THE PROJECTOR
Display 3D menu
Note:
‡‡
‡‡
‡‡
‡‡
‡‡
This projector is a 3D ready projector with DLP-Link 3D solution.
Please make sure your 3D glasses are use for DLP-Link 3D before enjoy your video.
This projector supports frame sequential (page-flip) 3D via HDMI1/HDMI2/VGA ports.
To enable 3D mode, the input frame rate should be set to 60Hz only, lower or higher frame rate is not
supported.
To reach the best performance, resolution 1920x1080 is recommended, please be noted that 4K
(3840x2160) resolution is not supported in 3D mode.
3D Mode
Use this option to enable or disable the 3D function.
‡‡
Off: Select “Off” to turn off 3D mode.
‡‡
On: Select “On” to turn on 3D mode.
Note: If the 2D and 3D sources enter PJ at the same time, if the ghosting image appears in the 2D source, make
sure to manually turn off the 3D function.
3D Tech
Set the 3D tech. parameter to “DLP-Link” or “3D Sync”.
3D → 2D
Use this option to specify how the 3D content should appear on the screen.
‡‡
3D: Display 3D signal.
‡‡
L (Left): Display the left frame of 3D content.
‡‡
R (Right): Display the right frame of 3D content.
3D Format
Use this option to select the appropriate 3D format content.
‡‡
Auto: When a 3D identification signal is detected, the 3D format is selected automatically.
‡‡
SBS: Display 3D signal in “Side-by-Side” format.
‡‡
Top and Bottom: Display 3D signal in “Top and Bottom” format.
‡‡
Frame Sequential: Display 3D signal in “Frame Sequential” format.
3D Sync Invert
Use this option to enable/disable the 3D sync invert function.
Reset
Return the factory default settings for 3D settings.
English
35
USING THE PROJECTOR
Display aspect ratio menu
Aspect Ratio
Select the aspect ratio of the displayed image between the following options:
‡‡
4:3: This format is for 4:3 input sources.
‡‡
16:9: This format is for 16:9 input sources, like HDTV and DVD enhanced for Wide screen TV.
‡‡
16:10 (for WUXGA model only): This format is for 16:10 input sources, like widescreen laptops.
‡‡
LBX: This format is for non-16x9, letterbox source and if you use external 16x9 lens to display 2.35:1
aspect ratio in full resolution.
‡‡
Native: This format displays the original image without any scaling.
‡‡
Auto: Automatically selects the appropriate display format.
‡‡
Detailed informations about LBX mode:
±±
Some Letter-Box Format DVDs are not enhanced for 16x9 TVs. In this situation, the image
will not look right when displaying image in 16:9 mode. In this situation, please try to use the
4:3 mode to view the DVD. If the content is not 4:3, there will be black bars around the image
in 16:9 display. For this type of content, you can use LBX mode to fill the image on the 16:9
display.
Note:
±±
If you use an external anamorphic lens, this LBX mode also allows you to watch a 2.35:1
content (include Anamorphic DVD and HDTV film source) that supports anamorphic wide is
enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Light
source power and vertical resolution are fully utilized.
1080p scaling table:
16:9 screen
480i/p
576i/p
1080i/p
720p
4x3
Scale to 1440x1080.
16x9
Scale to 1920x1080.
LBX
Scale to 1920x1440, then get the central 1920x1080 image to display.
Native mode
PC
- 1:1 mapping centered.
- No scaling will be made; the image is displayed with the resolution based on input source.
Auto
- If auto format is selected, the screen type will automatically become16:9 (1920x1080).
- If source is 4:3, the screen type will be scaled to 1440 x1080.
- If source is 16:9, the screen type will be scaled to 1920x1080.
- If source is 16:10, the screen type will be scaled to 1920x1200 and cut 1920x1080 area to
display.
36 English
USING THE PROJECTOR
1080p auto mapping rule:
Input resolution
Auto
4:3
Wide Laptop
SDTV
HDTV
Auto/Scale
H-resolution
V-resolution
1920
1080
640
480
1440
1080
800
600
1440
1080
1024
768
1440
1080
1280
1024
1440
1080
1400
1050
1440
1080
1600
1200
1440
1080
1280
720
1920
1080
1280
768
1800
1080
1280
800
1728
1080
720
576
1350
1080
720
480
1620
1080
1280
720
1920
1080
1920
1080
1920
1080
WUXGA scaling table for 1920 x 1200 DMD (screen type 16:10):
Note:
‡‡
Supported screen type 16:10 (1920 x 1200), 16:9 (1920x1080).
‡‡
When screen type is 16:9, the16x10 format becomes unavailable.
‡‡
When screen type is 16:10, the 16x9 format becomes unavailable.
‡‡
If you select auto option then the display mode will be also automatically changed.
16 : 10 screen
480i/p
4x3
Scale to 1600x1200.
16x10
Scale to 1920x1200.
LBX
Native mode
576i/p
1080i/p
720p
PC
Scale to 1920x1440, then get the central 1920x1200 image to display.
- 1:1 mapping centered.
- No scaling will be made; the image is displayed with the resolution based on input source.
Auto
- If this format is selected, the screen type will automatically become 16:10 (1920x1200).
- If source is 4:3, the screen type will be scaled to 1600x1200.
- If source is 16:9, the screen type will be scaled to 1920x1080.
- If source is 16:10, the screen type will be scaled to 1920x1200.
English
37
USING THE PROJECTOR
WUXGA auto mapping rule (screen type 16:10):
Auto
4:3
Wide Laptop
SDTV
HDTV
Input resolution
Auto/Scale
H-resolution
V-resolution
1920
1200
640
480
1600
1200
800
600
1600
1200
1024
768
1600
1200
1280
1024
1600
1200
1400
1050
1600
1200
1600
1200
1600
1200
1280
720
1920
1080
1280
768
1920
1152
1280
800
1920
1200
720
576
1500
1200
720
480
1800
1200
1280
720
1920
1080
1920
1080
1920
1080
WUXGA scaling table (screen type 16:9):
16 : 9 screen
480i/p
576i/p
1080i/p
720p
4x3
Scale to 1440x1080.
16x9
Scale to 1920x1080.
LBX
Scale to 1920x1440, then get the central 1920x1080 image to display.
Native mode
PC
- 1:1 mapping centered.
- No scaling will be made; the image is displayed with the resolution based on input source.
Auto
- If this format is selected, the screen type will automatically become 16:9 (1920x1080).
- If source is 4:3, the screen type will be scaled to 1440x1080.
- If source is 16:9, the screen type will be scaled to 1920x1080.
- If source is 16:10, the screen type will be scaled to 1920x1200 and cut 1920x1080 area to
display.
38 English
USING THE PROJECTOR
WUXGA auto mapping rule (screen type 16:9):
Auto
4:3
Wide Laptop
SDTV
HDTV
Input resolution
Auto/Scale
H-resolution
V-resolution
1920
1080
640
480
1440
1080
800
600
1440
1080
1024
768
1440
1080
1280
1024
1440
1080
1400
1050
1440
1080
1600
1200
1440
1080
1280
720
1920
1080
1280
768
1800
1080
1280
800
1728
1080
720
576
1350
1080
720
480
1620
1080
1280
720
1920
1080
1920
1080
1920
1080
Display edge mask menu
Edge Mask
Use this function to remove the video encoding noise on the edge of video source.
Display zoom menu
Zoom
Use to reduce or magnify an image on the projection screen.
Display image shift menu
Image Shift
Adjust the projected image position horizontally (H) or vertically (V).
Display geometric correction menu
Four Corners
Allow the image to be squeezed to fit an area defined by moving each of the four corners’ x and y position.
H Keystone
Adjust image distortion horizontally and make a squarer image. Horizontal keystone is used to correct a keystoned
image shape in which the left and right borders of the image are unequal in length. This is intended for use with
horizontally on-axis applications.
V Keystone
Adjust image distortion vertically and make a squarer image. Vertical keystone is used to correct a keystoned
image shape in which the top and bottom are slanted to one of the sides. This is intended when for use with
vertically on-axis applications.
English
39
USING THE PROJECTOR
Auto Keystone
Correct keystone digitally to fit the projected image on the area on which you are projecting.
Note:
‡‡
‡‡
The image size will reduce slightly when adjusting the horizontal and vertical keystone.
When the Auto Keystone is used, the Four Corner Adjustment function will be disabled.
Reset
Return the factory default settings for geometric correction settings.
Audio menu
Audio mute menu
Mute
Use this option to temporarily turn off the sound.
‡‡
On: Choose “On” to turn mute on.
‡‡
Off: Choose “Off” to turn mute off.
Note: “Mute” function affects both internal and external speaker volume.
Audio volume menu
Volume
Adjust the volume level.
Audio audio input menu
Audio Input
Select the audio input port for the video sources as follows:
‡‡
HDMI1/MHL: Audio 1, Audio 2, or Default.
‡‡
HDMI2: Audio 1, Audio 2, or Default.
‡‡
HDBaseT: Audio 1, Audio 2, or Default.
‡‡
VGA: Audio 1 and Audio 2.
‡‡
VGA 1: Audio 1 and Audio 2.
‡‡
VGA 2: Audio 1 and Audio 2.
‡‡
S-Video: Audio 1 and Audio 2.
‡‡
Video: Audio 1 and Audio 2.
‡‡
HDBaseT, VGA 1, VGA 2, and S-Video options are only applicable for HDBaseT model.
‡‡
VGA option is only applicable for non-HDBaseT model.
Note:
Audio audio / mic input function menu
Audio / Mic Input Function
Configure the audio input source setting.
40 English
USING THE PROJECTOR
Setup menu
Setup projection menu
Projection
Select the preferred projection between front, rear, ceiling-top, and rear-top.
Setup screen type menu
Screen Type (for WUXGA model only)
Choose the screen type from 16:9 and 16:10.
Setup power settings menu
Direct Power On
Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied,
without pressing the “Power” key on the projector keypad or on the remote control.
Signal Power On
Choose “On” to activate Signal Power mode. The projector will automatically power on when a signal is detected,
without pressing the “Power” key on the projector Keypad or on the remote control.
Auto Power Off (min.)
Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the
projector. The projector will automatically power off when the countdown has finished (in minutes).
Sleep Timer (min.)
Configure the sleep timer.
‡‡
Sleep Timer (min.): Sets the countdown timer interval. The countdown timer will start, with or without
a signal being sent to the projector. The projector will automatically power off when the countdown has
finished (in minutes).
Note: The Sleep Timer is reset every time when the projector is powered off.
‡‡
Always On: Check to set the sleep timer always on.
Power Mode (Standby)
Set the power mode setting.
‡‡
Active: Choose “Active” to return to normal standby.
‡‡
Eco: Choose “Eco.” to save power dissipation further < 0.5W.
USB Power (Standby)
Enable or disable the USB power function when the projector is in standby mode.
Note: The USB is not able to supply power with S-Video or MHL sources.
English
41
USING THE PROJECTOR
Setup security menu
Security
Enable this function to prompt for a password before using the projector.
‡‡
On: Choose “On” to use security verification when the turning on the projector.
‡‡
Off: Choose “Off” to be able to switch on the projector without password verification.
Security Timer
Can be select the time (Month/Day/Hour) function to set the number of hours the projector can be used. Once this
time has elapsed you will be requested to enter your password again.
Change Password
Use to set or modify the password that is prompted when turning the projector on.
Setup HDMI link settings menu
Note:
‡‡
When you connect HDMI CEC-compatible devices to the projector with HDMI cables, you can control
them on the same power on or power off status using the HDMI Link control feature in the projector’s
OSD. This lets one device or multiple devices in a group power on or power off via HDMI Link Feature
in a typical configuration, your DVD player may be connected to the projector through an amplifier or
home theater system.
HDMI
Amplifier
HDMI
DVD Player
HDMI Link
Enable/disable the HDMI Link function. The inclusive TV, power on link, and power off link options will only
available if the setting is set to “On”.
Inclusive of TV
Set to “Yes” if you prefer both TV and projector to be automatically turned off at the same time. To prevent both
devices to be turned off at the same time, set the setting to “No”.
Power On Link
CEC power on command.
‡‡
Mutual: Both projector and CEC device will be turned on simultaneously.
‡‡
PJ  Device: The CEC device will be turned on only after the projector is switched on.
‡‡
Device  PJ: The projector will be switched on only after the CEC device is turned on.
Power Off Link
Enable this function to let both HDMI Link and projector to be automatically turned off at the same time.
Setup test pattern menu
Test Pattern
Select the test pattern from green grid, magenta grid, white grid, white, or disable this function (off).
42 English
USING THE PROJECTOR
Setup remote settings menu
IR Function
Set the IR function setting.
‡‡
On: Choose “On”, the projector can be operated by the remote control from the top and front IR
receivers.
‡‡
Off: Choose “Off”, the projector can’t be operated by the remote control. By selecting “Off”, you will be
able to use the Keypad keys.
Remote Code
Set the remote custom code by pressing the remote ID button for 3 seconds and you will notice the remote
indicator (above the Off button) starts blinking. Then, input a number between 00-99 using the keyboard numbered
keys. After inserting the number, the remote indicator blinks twice quickly indicating that the remote code has
changed.
F1/F2/F3
Assign the default function for F1, F2, or F3 between Test Pattern, Brightness, Contrast, Sleep Timer, Color
Matching, Color Temp, Gamma, Projection, or MHL.
Setup projector ID menu
Projector ID
ID definition can be set up by menu (range 0-99), and allow user control an individual projector by using RS232 command.
Setup 12V trigger menu
12V Trigger
Use this function to enable or disable the trigger.
12V Trigger Output
Reserved
GND
‡‡
Off: Choose “Off” to disable the trigger.
‡‡
On: Choose “On” to enable the trigger.
Setup HDBaseT control menu
Ethernet / RS232
The projector can automatically detect the Ethernet or RS232 signal from the HDBaseT transmitter supplied. For an
automatic detection, make sure the respective signal is enabled.
HDBaseT Mode
Select the HDBaseT mode.
‡‡
‡‡
Auto: The projector will automatically detect the signal from HDBaseT transmitter supplied.
HDBaseT: The projector will activate Direct Power mode.
English
43
USING THE PROJECTOR
Setup options menu
Language
Select the multilingual OSD menu between English, German, French, Italian, Spanish, Portuguese, Polish, Dutch,
Swedish, Norwegian/Danish, Finnish, Greek, traditional Chinese, simplified Chinese, Japanese, Korean, Russian,
Hungarian, Czechoslovak, Arabic, Thai, Turkish, Farsi, Vietnamese, Indonesian, Romanian, and Slovenian.
Closed Captioning
Closed Captioning is a text version of the program sound or other information displayed on the screen. If the input
signal contains closed captions, you can turn on the feature and watch the channels. The available options include
“Off”, “CC1”, and “CC2”.
Menu Settings
Set the menu location on the screen and configure menu timer settings.
‡‡
Menu Location: Select the menu location on the display screen.
‡‡
Menu Timer: Set the duration where the OSD menu stays visible on the screen.
Auto Source
Choose this option to let the projector automatically find an available input source.
Input Source
Select the input source between HDMI1/MHL, HDMI2, HDBaseT, VGA, VGA 1, VGA 2, S-Video and Video.
Note:
‡‡
‡‡
HDBaseT, VGA 1, VGA 2, and S-Video options are only applicable for HDBaseT model.
VGA option is only applicable for non-HDBaseT model.
Input Name
Use to rename the input function for easier identification. The available options include HDMI1/MHL, HDMI2,
HDBaseT, VGA, VGA 1, VGA 2, S-Video, and Video.
Note:
‡‡
‡‡
HDBaseT, VGA 1, VGA 2, and S-Video options are only applicable for HDBaseT model.
VGA option is only applicable for non-HDBaseT model.
High Altitude
When “On” is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin.
Display Mode Lock
Choose “On” or “Off” to lock or unlock adjusting display mode settings.
Keypad Lock
When the keypad lock function is “On”, the Keypad will be locked. However, the projector can be operated by the
remote control. By selecting “Off”, you will be able to reuse the Keypad.
Information Hide
Enable this function to hide the information message.
44 English
‡‡
Off: Choose “Off” to show the “searching” message.
‡‡
On: Choose “On” to hide the info message.
USING THE PROJECTOR
Logo
Use this function to set the desired startup screen. If changes are made, they will take effect the next time the
projector is powered on.
‡‡
Default: The default startup screen.
‡‡
Neutral: Logo is not displayed on startup screen.
‡‡
User: Logo capture tool required.
Background Color
Use this function to display a blue, red, green, gray color, none, or logo screen when no signal is available.
Note: If the background color is set to “None”, then the background color is black.
Setup reset OSD menu
Reset OSD
Return the factory default settings for OSD menu settings.
Reset to Default
Return the factory default settings for all settings.
Network menu
Network LAN menu
Network Status
Display the network connection status (read-only).
MAC Address
Display the MAC address (read-only).
DHCP
Use this option to enable or disable the DHCP function.
‡‡
Off: To assign IP, subnet mask, gateway, and DNS configuration manually.
‡‡
On: Projector will obtain an IP address automatically from your network.
Note: Exiting OSD will automatically apply the entered values.
IP Address
Display the IP address.
Subnet Mask
Display subnet mask number.
Gateway
Display the default gateway of the network connected to the projector.
DNS
Display the DNS number.
English
45
USING THE PROJECTOR
How to use web browser to control your projector
1.
2.
3.
Note:
‡‡
‡‡
Turn “On” the DHCP option on projector to allow a DHCP server to automatically assign an IP address.
Open the web browser in your PC and type in the projector’s IP address (“Network > LAN > IP
Address”).
Enter the user name and password, and click “Login”.
The projector’s configuration web interface opens.
The default user name and password is “admin”.
The steps in this section is based on Windows 7 operating system.
Making a direct connection from your computer to the projector*
1.
2.
3.
Turn “Off” the DHCP option on the projector.
Configure the IP address, Subnet Mask, Gateway, and DNS on projector (“Network > LAN”).
Open Network and Sharing Center page on your PC, and assign the identical network parameters to
your PC as set on projector. Click “OK” to save the parameters.
4.
Open the web browser on your PC and type in to the URL field the IP address, assigned in step 3.
Then press “Enter” key.
Reset
Reset all values for LAN parameters.
Network control menu
Crestron
Use this function to select the network function (port: 41794).
For more information, please visit http://www.crestron.com and www.crestron.com/getroomview.
Extron
Use this function to select the network function (port: 2023).
PJ Link
Use this function to select the network function (port: 4352).
AMX Device Discovery
Use this function to select the network function (port: 9131).
46 English
USING THE PROJECTOR
Telnet
Use this function to select the network function (port: 23).
HTTP
Use this function to select the network function (port: 80).
Setup network control settings menu
LAN_RJ45 function
For simplicity and ease of operation, the projector provides diverse networking and remote management features.
The LAN / RJ45 function of the projector through a network, such as remotely manage: Power On / Off, brightness,
and contrast settings. Also, you can view the projector status information, such as: Video- Source, Sound-Mute, etc.
Projector
(Ethernet)
Wired LAN terminal functionalities
This projector can be controlled by using a PC (laptop) or other external device via LAN / RJ45 port and compatible
with Crestron / Extron / AMX (Device -Discovery) / PJLink.
‡‡
Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.
‡‡
Extron is a registered trademark of Extron Electronics, Inc. of the United States.
‡‡
AMX is a registered trademark of AMX LLC of the United States.
‡‡
PJLink applied for trademark and logo registration in Japan, the United States of America, and other
countries by JBMIA.
The projector is supported by the specified commands of the Crestron Electronics controller and related software,
for example RoomView®.
http://www.crestron.com/
This projector is compliant to support Extron device(s) for reference.
http://www.extron.com/
This projector is supported by AMX ( Device Discovery ).
http://www.amx.com/
This projector supports all commands of PJLink Class1 (Version 1.00).
http://pjlink.jbmia.or.jp/english/
For more detailed information about the various types of external devices which can be connected to the LAN /
RJ45 port and remote control the projector, as well as the supported commands for these external devices, please
contact the Support-Service directly.
English
47
USING THE PROJECTOR
LAN RJ45
48 English
1.
Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop).
2.
On the PC (Laptop), select Start > Control Panel > Network Connections.
3.
Right-click on the Local Area Connection, and select Property.
4.
In the Properties window, select the General tab, and select Internet Protocol (TCP / IP).
USING THE PROJECTOR
5.
Click “Properties”.
6.
Type in the IP address and Subnet mask, then press “OK”.
7.
Press the “Menu” button on the projector.
8.
Open on projector Network > LAN.
9.
Enter the following connection parameters:
±±
DHCP: Off
±±
IP Address: 192.168.0.100
±±
Subnet Mask: 255.255.255.0
±±
Gateway: 192.168.0.254
±±
DNS: 192.168.0.51
10.
11.
Press “Enter” to confirm settings.
Open a web browser, for example Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher
installed.
12.
In the Address bar, input the projector’s IP address: 192.168.0.100.
13.
Press “Enter”.
The projector is setup for remote management. The LAN / RJ45 function displays as follows:
English
49
USING THE PROJECTOR
Information page
Main page
Tool page
Contact IT helpdesk
50 English
USING THE PROJECTOR
RS232 by Telnet Function
There is alternative RS232 command control way, in projector so called “RS232 by TELNET” for LAN / RJ45
interface.
Quick Start-Guide for “RS232 by Telnet”
‡‡
Check and get the IP address on OSD of the projector.
‡‡
Make sure that the PC / laptop can access the web-page of the projector.
‡‡
Make sure that “Windows Firewall” setting is set disabled in case of “TELNET” function filtering out by
PC / laptop.
1.
Select Start > All Programs.> Accessories > Command Prompt.
2.
Input the command format as follows:
±±
telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)
±±
(ttt.xxx.yyy.zzz: IP-Address of the projector)
3.
If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key pressed, the
RS232 command will be workable.
Specification for “RS232 by TELNET”:
1.
2.
3.
4.
5.
Telnet: TCP.
Telnet port: 23 (for more detail, kindly please get contact with the service agent or team).
Telnet utility: Windows “TELNET.exe” (console mode).
Disconnection for RS232-by-Telnet control normally: Close
Windows Telnet utility directly after TELNET connection ready.
±±
Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload for
Telnet-Control application.
±±
Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232 command for
Telnet-Control.
±±
Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more than 200 (ms).
English
51
USING THE PROJECTOR
Info menu
Info menu
View the projector information as listed below:
52 English
‡‡
Regulatory
‡‡
Serial Number
‡‡
Source
‡‡
Resolution
‡‡
Refresh Rate
‡‡
Display Mode
‡‡
Remote Code
‡‡
Remote Code(Active)
‡‡
Power Mode (Standby)
‡‡
Light Source Hours
‡‡
Network Status
‡‡
IP Address
‡‡
Projector ID
‡‡
Brightness Mode
‡‡
FW Version
MAINTENANCE
Installing and cleaning the dust filter
Installing the dust filter
2
2
1
1
Note: Dust filters are only required/supplied in the selected regions with excessive dust.
Cleaning the dust filter
We recommend you to clean the dust filter every three months. Clean it more often if the projector is used in a
dusty environment.
Procedure:
1.
Switch off the power to the projector by pressing the " " button on the projector keypad or the “
button on the remote control.
2.
Disconnect the power cord.
3.
Pull the dust filter compartment downwards to remove it out from the bottom of the projector. 1
4.
Carefully remove the air filter. Then clean or replace the dust filter. 2
5.
To install the dust filter, reverse the previous steps.
”
1
2
1
2
English
53
ADDITIONAL INFORMATION
Compatible resolutions
Digital (HDMI 1.4)
Native resolution: 1920 x 1080 @ 60Hz (1080P); 1920 x 1200 @ 60Hz (WUXGA)
B0 / Established
Timing
B0 / Standard
Timing
B0 / Detail Timing:
B1 / Video Mode
B1 / Detail Timing:
720 x 400 @ 70Hz
1080P/WUXGA:
Native timing: 1080P:
640 x 480p @ 60Hz 4:3
1366 x 768 @ 60Hz
640 x 480 @ 60Hz
1280 x 720 @ 60Hz
1920 x 1080 @ 60Hz
720 x 480p @ 60Hz 4:3
1920 x 1080p @ 60Hz
640 x 480 @ 67Hz
1280 x 800 @ 60Hz
WUXGA:
1280 x 720p @ 60Hz 16:9
1920 x 1080 @120Hz
640 x 480 @ 72Hz
1280 x 1024 @ 60Hz
1920 x 1200 @ 60Hz
1920 x 1080i @ 60Hz 16:9
1920 x 1200 @ 60Hz
(RB) (1080P)
640 x 480 @ 75Hz
1024 x 768 @ 120Hz
720 x 480i @ 60Hz 16:9
800 x 600 @ 56Hz
640 x 480 @ 120Hz
1920 x 1080p @ 60Hz 16:9
800 x 600 @ 60Hz
800 x 600 @ 120Hz
720 x 576p @ 50Hz 4:3
800 x 600 @ 72Hz
1280 x 800 @ 120Hz
1280 x 720p @ 50Hz 16:9
800 x 600 @ 75Hz
1920 x 1080i @ 50Hz 16:9
832 x 624 @ 75Hz
720 x 576i @ 50Hz 16:9
1024 x 768 @ 60Hz
1920 x 1080p @ 50Hz 16:9
1024 x 768 @ 70Hz
1920 x 1080p @ 24Hz 16:9
1024 x 768 @ 75Hz
720 x 480p @ 60Hz 16:9
1280 x 1024 @ 75Hz
720 x 576p @ 50Hz 16:9
1152 x 870 @ 75Hz
3840 x 2160 @ 24Hz
3840 x 2160 @ 25Hz
3840 x 2160 @ 30Hz
4096 x 2160 @ 24Hz
Digital (HDMI 2.0)
Native resolution: 1920 x 1080 @ 60Hz (1080P); 1920 x 1200 @ 60Hz (WUXGA)
B0 / Established
Timing
B0 / Standard
Timing
B0 / Detail Timing:
B1 / Video Mode
B1 / Detail Timing:
720 x 400 @ 70Hz
800 x 600 @120Hz
Native timing: 1080P:
640 x 480p @ 60Hz 4:3
1366 x 768 @ 60Hz
640 x 480 @ 60Hz
1024 x 768 @120Hz
1920 x 1080 @ 60Hz
720 x 480i @ 60Hz 16:9
1920 x 1080 @120Hz
640 x 480 @ 67Hz
1280 x 800 @ 60Hz
WUXGA:
720 x 480p @ 60Hz 4:3
640 x 480 @ 72Hz
1280 x 1024 @ 60Hz
1920 x 1200 @ 60Hz
720 x 480p @ 60Hz 16:9
640 x 480 @ 75Hz
1280 x 720 @ 60Hz
720 x 576i @ 50Hz 16:9
800 x 600 @ 56Hz
640 x 480 @120Hz
720 x 576p @ 50Hz 4:3
800 x 600 @ 60Hz
1280 x 800 @120Hz
720 x 576p @ 50Hz 16:9
800 x 600 @ 72Hz
1280 x 720p @ 60Hz 16:9
800 x 600 @ 75Hz
1280 x 720p @ 50Hz 16:9
832 x 624 @ 75Hz
1920 x 1080i @ 60Hz 16:9
1024 x 768 @ 60Hz
1920 x 1080i @ 50Hz 16:9
1024 x 768 @ 70Hz
1920 x 1080p @ 60Hz 16:9
1024 x 768 @ 75Hz
1920 x 1080p @ 50Hz 16:9
1280 x 1024 @ 75Hz
1920 x 1080p @ 24Hz 16:9
1152 x 870 @ 75Hz
3840 x 2160 @ 24Hz 16:9
3840 x 2160 @ 25Hz 16:9
3840 x 2160 @ 30Hz 16:9
4096 x 2160 @ 24Hz
256:135
54 English
ADDITIONAL INFORMATION
B0 / Established
Timing
B0 / Standard
Timing
B0 / Detail Timing:
B1 / Video Mode
B1 / Detail Timing:
3840 x 2160 @ 50Hz 16:9
3840 x 2160 @ 60Hz 16:9
4096 x 2160 @ 50Hz
256:135
4096 x 2160 @ 60Hz
256:135
4096 x 2160 @ 25Hz
256:135
4096 x 2160 @ 30Hz
256:135
Analog
Native resolution: 1920 x 1080 @ 60Hz (1080P); 1920 x 1200 @ 60Hz (WUXGA)
B0 / Established Timing
B0 / Standard Timing
B0 / Detail Timing
B1 / Detail Timing
720 x 400 @ 70Hz
1080P/WUXGA:
Native timing: 1080P:
1366 x 768 @ 60Hz
640 x 480 @ 60Hz
1280 x 720 @ 60Hz
1920 x 1080 @ 60Hz
1280 x 800 @ 120Hz (RB)
640 x 480 @ 67Hz
1280 x 800 @ 60Hz
Native timing: WUXGA:
1920 x 1200 @ 60Hz (RB)
(1080P)
640 x 480 @ 72Hz
1280 x 1024 @ 60Hz
1920 x 1200 @ 60Hz
640 x 480 @ 75Hz
1024 x 768 @ 120Hz
800 x 600 @ 56Hz
640 x 480 @ 120Hz
800 x 600 @ 60Hz
800 x 600 @120Hz
800 x 600 @ 72Hz
800 x 600 @ 75Hz
832 x 624 @ 75Hz
1024 x 768 @ 60Hz
1024 x 768 @ 70Hz
1024 x 768 @ 75Hz
1280 x 1024 @ 75Hz
1152 x 870 @ 75Hz
English
55
ADDITIONAL INFORMATION
True 3D video compatibility
Input timing
HDMI 1.4a
3D Input
Input
resolutions
1280 x 720P @ 50Hz
Top-and-Bottom
1280 x 720P @ 60Hz
Top-and-Bottom
1280 x 720P @ 50Hz
Frame packing
1280 x 720P @ 60Hz
Frame packing
1920 x 1080i @ 50Hz
Side-by-Side(Half)
1920 x 1080i @ 60Hz
Side-by-Side(Half)
1920 x 1080P @ 24Hz
Top-and-Bottom
1920 x 1080P @ 24Hz
Frame packing
1920 x 1080i @ 50Hz
1920 x 1080i @ 60Hz
1280 x 720P @ 50Hz
Side-by-Side(Half)
SBS mode is on
Top-and-Bottom
TAB mode is on
HQFS
3D format is Frame sequential
1280 x 720P @ 60Hz
HDMI 1.3
1920 x 1080i @ 50Hz
1920 x 1080i @ 60Hz
1280 x 720P @ 50Hz
1280 x 720P @ 60Hz
480i
Note:
‡‡
‡‡
‡‡
56 English
If 3D input is [email protected], the DMD should replay with integral multiple with 3D mode.
Support NVIDIA 3DTV Play if there is no patent fee from Optoma.
[email protected] and [email protected] will run in 100Hz, other 3D timing will run in 120Hz, and [email protected]
will run in 144Hz.
ADDITIONAL INFORMATION
Image size and projection distance
1080P
Desired Image Size
Diagonal
Projection Distance (C)
Width
Height
Wide
Tele
m
inch
m
inch
m
inch
m
feet
0.78
30.6
0.68
26.67
0.38
15.00
/
/
1.3
m
4.27
feet
1.02
40
0.89
34.86
0.50
19.61
/
/
1.7
5.58
1.27
50
1.11
43.58
0.62
24.51
1.3
4.36
2.1
6.97
1.52
60
1.33
52.29
0.75
29.42
1.6
5.23
2.6
8.37
1.78
70
1.55
61.01
0.87
34.32
1.9
6.10
3.0
9.76
2.03
80
1.77
69.73
1.00
39.22
2.1
6.97
3.4
11.16
2.29
90
1.99
78.44
1.12
44.12
2.4
7.84
3.8
12.55
2.54
100
2.21
87.16
1.25
49.03
2.7
8.72
4.3
13.95
3.05
120
2.66
104.59
1.49
58.83
3.2
10.46
5.1
16.73
3.81
150
3.32
130.74
1.87
73.54
4.0
13.07
6.4
20.92
4.57
180
3.98
156.88
2.24
88.25
4.8
15.69
7.7
25.10
5.08
200
4.43
174.32
2.49
98.05
5.3
17.43
8.5
27.89
6.35
250
5.53
217.89
3.11
122.57
6.6
21.79
/
/
7.65
301
6.66
262.34
3.75
147.57
8.0
26.23
/
/
Lens Shift Range
PJ lens Center to top of image
Vertical +
Vertical -
(Max) (A)
(Min) (B)
Vertical Shift
Range
Image Shift Range
Vertical range at any
Horizontal position
Horizontal +
Horizontal -
(Right)
(Left)
cm
cm
cm
cm
cm
cm
48.4
40.4
8.0
N/A
0
0
63.3
52.8
10.5
N/A
0
0
79.1
66.0
13.1
N/A
0
0
94.9
79.2
15.7
N/A
0
0
110.7
92.4
18.3
N/A
0
0
126.5
105.6
20.9
N/A
0
0
142.3
118.8
23.5
N/A
0
0
158.1
132.0
26.2
N/A
0
0
189.8
158.4
31.4
N/A
0
0
237.2
198.0
39.2
N/A
0
0
284.7
237.6
47.1
N/A
0
0
316.3
264.0
52.3
N/A
0
0
395.4
330.0
65.4
N/A
0
0
476.0
397.3
78.7
N/A
0
0
English
57
ADDITIONAL INFORMATION
WUXGA
Desired Image Size
Diagonal
Projection Distance (C)
Width
Height
Wide
Tele
m
inch
m
inch
m
inch
m
feet
0.80
31.5
0.68
26.71
0.42
16.69
/
/
1.3
m
4.27
feet
1.02
40
0.86
33.92
0.54
21.20
/
/
1.7
5.43
1.27
50
1.08
42.40
0.67
26.50
1.3
4.24
2.1
6.78
1.52
60
1.29
50.88
0.81
31.80
1.6
5.09
2.5
8.14
1.78
70
1.51
59.36
0.94
37.10
1.8
5.94
2.9
9.50
2.03
80
1.72
67.84
1.08
42.40
2.1
6.78
3.3
10.85
2.29
90
1.94
76.32
1.21
47.70
2.3
7.63
3.7
12.21
2.54
100
2.15
84.80
1.35
53.00
2.6
8.48
4.1
13.57
3.05
120
2.58
101.76
1.62
63.60
3.1
10.18
5.0
16.28
3.81
150
3.23
127.20
2.02
79.50
3.9
12.72
6.2
20.35
4.57
180
3.88
152.64
2.42
95.40
4.7
15.26
7.4
24.42
5.08
200
4.31
169.60
2.69
106.00
5.2
16.96
8.3
27.14
6.35
250
5.38
212.00
3.37
132.50
6.5
21.20
/
/
7.65
301
6.48
255.25
4.05
159.53
7.8
25.52
/
/
Lens Shift Range
PJ lens Center to top of image
Image Shift Range
Vertical +
Vertical -
Vertical range at any
Horizontal position
Horizontal -
(Min) (B)
Vertical Shift
Range
Horizontal +
(Max) (A)
(Right)
(Left)
cm
cm
cm
cm
cm
cm
50.9
42.4
8.5
N/A
0
0
64.6
53.8
10.8
N/A
0
0
80.8
67.3
13.5
N/A
0
0
96.9
80.8
16.2
N/A
0
0
113.1
94.2
18.8
N/A
0
0
129.2
107.7
21.5
N/A
0
0
145.4
121.2
24.2
N/A
0
0
161.5
134.6
26.9
N/A
0
0
193.9
161.5
32.3
N/A
0
0
242.3
201.9
40.4
N/A
0
0
290.8
242.3
48.5
N/A
0
0
323.1
269.2
53.8
N/A
0
0
403.9
336.5
67.3
N/A
0
0
486.2
405.2
81.0
N/A
0
0
Projection distance
V+
V-
V
A
B
C
58 English
ADDITIONAL INFORMATION
Projector dimensions and ceiling mount installation
1.
2.
To prevent damage to your projector, please use the Optoma ceiling mount.
If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to
the projector meet the following specifications:
‡‡
Screw type: M4*5
‡‡
Minimum screw length: 5mm
Unit: mm
Note: Please note that damage resulting from incorrect installation will void the warranty.
English
59
ADDITIONAL INFORMATION
Warning:
‡‡
If you buy a ceiling mount from another company, please be sure to use the correct screw size.
Screw size will vary depending on the thickness of the mounting plate.
‡‡
Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.
‡‡
Avoid installing the projector near a heat source.
IR remote codes
On
Off
Geometric
Correction
PIP/PBP
F1
F2
AV Mute
Mode
ENTER
Info.
Source
Re-Sync
F3
Volume
D Zoom
Menu
Format Freeze
Remote
ID
All
VGA S-Video HDMI1 HDMI2
1
2
HDBaseT Video
4
BNC
7
Key
Printing-key
definition
5
3
DVI
HDMI3
6
YPbPr DisplayPort 3D
8
9
0
Key code
BYTE1
BYTE2
BYTE3
BYTE4
customer 0
customer 1
data 0
data 1
Repeat
Power On
On
32
CD
02
#BYTE3
F1
Power Off
Off
32
CD
2E
#BYTE3
F1
Geometric
Correction
Geometric
Correction
32
CD
96
#BYTE3
F1
PIP/PBP
32
CD
78
#BYTE3
F1
F1
F1
32
CD
26
#BYTE3
F1
F2
F2
32
CD
27
#BYTE3
F1
Mode
32
CD
95
#BYTE3
F1
PIP/PBP
Mode
60 English
ADDITIONAL INFORMATION
Key
Printing-key
definition
Key code
BYTE1
BYTE2
BYTE3
BYTE4
customer 0
customer 1
data 0
data 1
Up arrow
32
CD
C6
#BYTE3
F1
Down arrow
32
CD
C7
#BYTE3
F1
Left arrow
32
CD
C8
#BYTE3
F1
Right arrow
32
CD
C9
#BYTE3
F1
Enter
32
CD
C5
#BYTE3
F1
AV Mute
32
CD
03
#BYTE3
F1
Information
Info.
32
CD
25
#BYTE3
F1
Laser
Laser
N/A
N/A
N/A
N/A
N/A
Source
32
CD
18
#BYTE3
F1
F3
32
CD
66
#BYTE3
F1
Re-Sync
32
CD
04
#BYTE3
F1
Volume +
32
CD
09
#BYTE3
F1
Volume -
32
CD
0C
#BYTE3
F1
D Zoom +
32
CD
08
#BYTE3
F1
D Zoom -
32
CD
0B
#BYTE3
F1
Menu
32
CD
88
#BYTE3
F1
Format
Format
32
CD
15
#BYTE3
F1
Freeze
Freeze
32
CD
06
#BYTE3
F1
ID
N/A
N/A
3201~ 3299
N/A
N/A
All
N/A
N/A
32CD
N/A
N/A
1/VGA
32
CD
8E
#BYTE3
F1
2 / S-Video
2/S-Video
32
CD
1D
#BYTE3
F1
3 / HDMI1
3/HDMI1
32
CD
16
#BYTE3
F1
HDMI2
32
CD
9B
#BYTE3
F1
4/HDBaseT
32
CD
70
#BYTE3
F1
5/Video
32
CD
1C
#BYTE3
F1
6
32
CD
19
#BYTE3
F1
HDMI3
32
CD
98
#BYTE3
F1
7
32
CD
1A
#BYTE3
F1
8/YPbPr
32
CD
17
#BYTE3
F1
9
32
CD
9F
#BYTE3
F1
0/3D
32
CD
89
#BYTE3
F1
F3
32
CD
66
#BYTE3
F1
Four
directional
select keys
( / / / )
Enter
AV Mute
Source
F3
Re-Sync
Volume
D Zoom
Menu
Remote
1 / VGA
HDMI2
4 / HDBaseT
5 / Video
6
HDMI3
7
8 / YPbPr
9
0 / 3D
F3
Repeat
English
61
ADDITIONAL INFORMATION
Troubleshooting
If you experience a problem with your projector, please refer to the following information. If a problem persists,
please contact your local reseller or service center.
Image problems
No image appears on-screen
‡‡
Ensure all the cables and power connections are correctly and securely connected as described in the
"Installation" section.
‡‡
Ensure the pins of connectors are not crooked or broken.
‡‡
Ensure that the "Mute" feature is not turned on.
Image is out of focus
‡‡
Turn the focus ring clockwise or counterclockwise until the image is sharp and legible. (Please see
page 17).
‡‡
Make sure the projection screen is between the required distance from the projector. (Please refer to
pages 57-58).
The image is stretched when displaying 16:9 DVD title
‡‡
When you play anamorphic DVD or 16:9 DVD, the projector will show the best image in 16: 9 format
on projector side.
‡‡
If you play the LBX format DVD title, please change the format as LBX in projector OSD.
‡‡
If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD.
‡‡
Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player.
Image is too small or too large
‡‡
Move the projector closer to or further from the screen.
‡‡
Press "Menu" on the projector panel, go to "Display → Aspect Ratio". Try the different settings.
Image has slanted sides:
‡‡
If possible, reposition the projector so that it is centered on the screen and below the bottom of the
screen.
Image is reversed
‡‡
62 English
Select "Setup → Projection" from the OSD and adjust the projection direction.
ADDITIONAL INFORMATION
Other problems
The projector stops responding to all controls
‡‡
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Remote control problems
If the remote control does not work
‡‡
Check the operating angle of the remote control is pointed within ±15° to the IR receiver on the
projector.
‡‡
Make sure there are not any obstructions between the remote control and the projector. Move to within
6 m (19.7 ft) of the projector.
‡‡
Make sure batteries are inserted correctly.
‡‡
Replace batteries if they are exhausted.
English
63
ADDITIONAL INFORMATION
Warning indicators
When the warning indicators (see below) light up or flash, the projector will automatically shutdown:
‡‡
“Lamp” LED indicator is lit red and if “Power” indicator flashes red.
‡‡
“Temp” LED indicator is lit red and if “Power” indicator flashes red. This indicates the projector has
overheated. Under normal conditions, the project can be switched back on.
‡‡
“Temp” LED indicator flashes red and if “Power” indicator flashes red.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or
flash, please contact your nearest service center for assistance.
LED lightning messages
Power LED
Message
Standby state
(Input power cord)
(Red)
Lamp LED
(Red)
(Red)
Steady light
Flashing
(0.5 sec off / 0.5 sec
on)
Power on (Warming)
Power on and Lamp lighting
Power off
(Blue) or (Green)
Temp LED
Steady light
Steady light
Error (Lamp failure)
Flashing
Error (Fan failure)
Flashing
Flashing
Error (Over temp.)
Flashing
Steady light
‡‡
Power off:
Power Off
Press power key again.
‡‡
Temperature warning:
Warning
TEMPERATURE TOO HIGH
Please:
1. Make sure air in and outlets are not blocked.
2. Make sure the environment temperature is under 45 degree C.
If the problem persists in spite of the above.
Please contact a service center for repair.
64 English
Steady light
ADDITIONAL INFORMATION
Specifications
Optical
Description
Maximum resolution
WUXGA
Native resolution
‡‡ 1080p
‡‡ WUXGA
Lens
Manual zoom and manual focus
Image size (diagonal)
1080p (optimized at 82”):
‡‡ 30.6”~301.1” (mechanism travel)
‡‡ 30.6”–112.9”(full optical performance)
WUXGA (optimized at 82”):
‡‡ 31.5”–301.8” (mechanism travel)
‡‡ 31.5”–116” (full optical performance)
Projection distance
‡‡ 1.3m to 10m mechanism travel
‡‡ 1.3m to 3m optical performance range
Electrical
Description
Inputs
‡‡
‡‡
‡‡
‡‡
‡‡
‡‡
‡‡
‡‡
‡‡
HDMI 1 v1.4a
HDMI 2 v2.0 / 4K/MHL v2.2
VGA-IN 1
VGA-IN 2 (only for WUXGA model)
VIDEO (RCA connector (Y))
AUDIO-IN 1 3.5mm
AUDIO-IN 2 3.5mm, with microphone
USB Type-A for power USB 5V/1.5A
S-VIDEO (only for WUXGA model) (*)
Outputs
‡‡ VGA-OUT
‡‡ AUDIO-OUT 3.5mm
‡‡ 12V OUT Trigger
Control
‡‡
‡‡
‡‡
‡‡
Color reproduction
1073.4 Million color
Scan rate
‡‡ Horizontal scan rate: 15.375~91.146 KHz
‡‡ Vertical scan rate: 24~85 Hz (120Hz for 3D feature projector)
Built-in speaker
Yes, 10W x2
Power requirement
100 - 240V ±10%, AC 50/60Hz
Input current
4.6A
USB Type A for mouse
RS232
RJ-45 (support web control)
HDBaseT (only for WUXGA model)
Mechanical
Description
Installation orientation
Front, Rear, Ceiling, Rear-top, Portrait
Dimensions
‡‡ 374.0mm (W) x 302mm (D) x 107mm (H) (without feet)
‡‡ 374.0mm (W) x 302mm (D) x 117mm( H) (with feet)
Weight
5.6 ±0.5kg
Environmental conditions
Operating in 5~40°C , 10% to 85% humidity (non-condensing)
Note:
‡‡
‡‡
All specifications are subject to change without notice.
(*) During video playback from S-Video source, the USB charging function is disabled.
English
65
ADDITIONAL INFORMATION
Optoma global offices
For service or support, please contact your local office.
USA
47697 Westinghouse Drive,
Fremont, CA 94539, USA
www.optomausa.com
Canada
47697 Westinghouse Drive,
Fremont, CA 94539, USA
www.optomausa.com
Latin America
47697 Westinghouse Drive,
Fremont, CA 94539, USA
www.optomausa.com
Europe
Unit 1, Network 41, Bourne End Mills
Hemel Hempstead, Herts,
HP1 2UJ, United Kingdom
www.optoma.eu
Service Tel : +44 (0)1923 691865
Benelux BV
Randstad 22-123
1316 BW Almere
The Netherlands
www.optoma.nl
France
Bâtiment E
81-83 avenue Edouard Vaillant
92100 Boulogne Billancourt, France
Spain
C/ José Hierro,36 Of. 1C
28522 Rivas VaciaMadrid,
Spain
Deutschland
Wiesenstrasse 21 W
D40549 Düsseldorf,
Germany
Scandinavia
Lerpeveien 25
3040 Drammen
Norway
Japan
888-289-6786
東京都足立区綾瀬3-25-18
510-897-8601
株式会社オーエス
[email protected]
コンタクトセンター:0120-380-495
Taiwan
888-289-6786
12F., No.213, Sec. 3, Beixin Rd.,
+886-2-8911-8600
510-897-8601
+886-2-8911-6550
[email protected] Xindian Dist., New Taipei City 231,
Taiwan, R.O.C.
[email protected]
www.optoma.com.tw
asia.optoma.com
888-289-6786
Hong Kong
510-897-8601
[email protected] Unit A, 27/F Dragon Centre,
79 Wing Hong Street,
Cheung Sha Wan,
Kowloon, Hong Kong
+44 (0) 1923 691 800
+44 (0) 1923 691 888
[email protected]
+31 (0) 36 820 0252
+31 (0) 36 548 9052
+33 1 41 46 12 20
+33 1 41 46 94 35
[email protected]
+34 91 499 06 06
+34 91 670 08 32
+49 (0) 211 506 6670
+49 (0) 211 506 66799
[email protected]
+47 32 98 89 90
+47 32 98 89 99
[email protected]
PO.BOX 9515
3038 Drammen
Norway
Korea
WOOMI TECH.CO.,LTD.
4F, Minu Bldg.33-14, Kangnam-Ku,
Seoul,135-815, KOREA
korea.optoma.com
66 English
[email protected]
www.os-worldwide.com
+82+2+34430004
+82+2+34430005
China
5F, No. 1205, Kaixuan Rd.,
Changning District
Shanghai, 200052, China
+852-2396-8968
+852-2370-1222
www.optoma.com.hk
+86-21-62947376
+86-21-62947375
www.optoma.com.cn
www.optoma.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement