Optoma ZH510T-B User Manual

Optoma ZH510T-B User Manual
DLP® Projector
User’s Manual
TABLE OF CONTENTS
SAFETY..................................................................................................3
Regulation & Safety Notices........................................................................................................5
INTRODUCTION.....................................................................................8
Package Overview......................................................................................................................8
Product Overview........................................................................................................................9
Main Unit..................................................................................................................................9
Control Panel..........................................................................................................................10
Connections........................................................................................................................... 11
Remote Control......................................................................................................................12
SETUP AND INSTALLATION...............................................................14
Connecting Source to the Projector..........................................................................................14
Powering the Projector On/Off..................................................................................................16
Warning Indicator...................................................................................................................17
Adjusting the Projected Image..................................................................................................18
USER CONTROLS...............................................................................21
Using the Control Panel............................................................................................................21
On-screen Display Menus.........................................................................................................22
How to operate.......................................................................................................................22
Structure.................................................................................................................................23
Picture....................................................................................................................................27
Screen....................................................................................................................................29
Settings..................................................................................................................................31
Volume...................................................................................................................................32
Options...................................................................................................................................33
3D...........................................................................................................................................36
LAN........................................................................................................................................37
APPENDICES.......................................................................................38
Projector Problems.................................................................................................................38
How to use web browser to control your projector.................................................................40
Crestron RoomView Control Tool..............................................................................................41
Installing and Cleaning the Optional Dust Filter........................................................................43
Compatibility Modes..................................................................................................................44
Ceiling Mount Installation..........................................................................................................47
Optoma global offices................................................................................................................48
2
English
SAFETY
The lightning flash with arrow head within an equilateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO
NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Important Safety Instruction
1.Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over
heating, it is recommended to install the projector in a location that does not block ventilation. As an example,
do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure
such as a book case or a cabinet that restricts air flow.
2.Do not use the projector near water or moisture. To reduce the risk of fire and/or electric shock, do not expose
the projector to rain or moisture.
3.Do not install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers
that emits heat.
4.Clean only with dry cloth.
5.Only use attachments/accessories specified by the manufacturer.
6. Do not use the unit if it has been physically damaged or abused.
Physical damage/abuse would be (but not limited to):
 Unit has been dropped.
 Power supply cord or plug has been damaged.
 Liquid has been spilled on to the projector.
 Projector has been exposed to rain or moisture.
 Something has fallen in the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages
or other hazards.
7.Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts
that could result in fire or electric shock.
8.See projector enclosure for safety related markings.
9.The unit should only be repaired by appropriate service personnel.
English
3
Precautions
Please follow all warnings, precautions and maintenance as recommended in this user’s
guide.
▀■ Warning- Do not look into the projector’s lens when the light source is on. The bright light may hurt and damage
your eyes.
▀■ Warning- To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture.
▀■ Warning- Please do not open or disassemble the projector as this may cause electric shock.
▀■ Warning- Please do not open or disassemble the projector as this may cause electric shock.
Do:
•
•
•
Turn off and unplug the power plug from the AC outlet before cleaning the product.
Use a soft dry cloth with mild detergent to clean the display housing.
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
Do not:
•
•
•
Block the slots and openings on the unit provided for ventilation.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
- In extremely hot, cold or humid environments.
 Sea level to 6000 feet
Extremely hot: > 35°C
Extremely cool: < 5°C
 6000 feet above
Extremely hot: > 30°C
Extremely cool: < 5°C
 Extremely humid: > 70% R.H. (Relative Humidity)
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
3D Safety Information
Please follow all warnings and precautions as recommended before you or your child use the 3D function.
Warning
Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be
closely supervised when viewing these images.
Photosensitive Seizure Warning and Other Health Risks
- Some viewers may experience an epileptic seizure or stroke when exposed to certain flashing images or lights
contained in certain Projector pictures or video games. If you suffer from, or have a family history of epilepsy
or strokes, please consult with a medical specialist before using the 3D function.
- Even those without a personal or family history of epilepsy or stroke may have an undiagnosed condition that
can cause photosensitive epileptic seizures.
- Pregnant women, the elderly, sufferers of serious medical conditions, those who are sleep deprived or under
the influence of alcohol should avoid utilizing the unit’s 3D functionality.
- If you experience any of the following symptoms, stop viewing 3D pictures immediately and consult a medical
specialist: (1) altered vision; (2) light-headedness; (3) dizziness; (4) involuntary movements such as eye or
muscle twitching; (5) confusion; (6) nausea; (7) loss of awareness; (8) convulsions; (9) cramps; and/ or (10)
disorientation. Children and teenagers may be more likely than adults to experience these symptoms. Parents
should monitor their children and ask whether they are experiencing these symptoms.
4
English
- Watching 3D projection may also cause motion sickness, perceptual after effects, disorientation, eye strain
and decreased postural stability. It is recommended that users take frequent breaks to lessen the potential of
these effects. If your eyes show signs of fatigue or dryness or if you have any of the above symptoms, immediately discontinue use of this device and do not resume using it for at least thirty minutes after the symptoms
have subsided.
- Watching 3D projection while sitting too close to the screen for an extended period of time may damage your
eyesight. The ideal viewing distance should be at least three times the screen height. It is recommended that
the viewer’s eyes are level with the screen.
- Watching 3D projection while wearing 3D glasses for an extended period of time may cause a headache or
fatigue. If you experience a headache, fatigue or dizziness, stop viewing the 3D projection and rest.
- Do not use the 3D glasses for any other purpose than for watching 3D projection.
- Wearing the 3D glasses for any other purpose (as general spectacles, sunglasses, protective goggles, etc.)
may be physically harmful to you and may weaken your eyesight.
- Viewing in 3D projection may cause disorientation for some viewers. Accordingly, DO NOT place your 3D
PROJECTOR near open stairwells, cables, balconies, or other objects that can be tripped over, run into,
knocked down, broken or fallen over.
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright
laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced
without written consent of the author.
© Copyright 2015
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations
or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make
changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such
revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and
Windows are trademarks or registered trademarks of Microsoft Corporation.
Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated.
DLP, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a trademark of Texas Instruments.
All other product names used in this manual are the properties of their respective owners and are Acknowledged.
Regulation & Safety Notices
This appendix lists the general notices of your projector.
FCC notice
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
English
5
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with
FCC regulations.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user’s authority, which is
granted by the Federal Communications Commission, to operate this projector.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired
operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian
ICES-003.
Remarque à l’intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
• EMC Directive 2004/108/EC (including amendments)
• Low Voltage Directive 2006/95/EC
• R & TTE Directive 1999/5/EC (if product has RF function)
Disposal instructions
Do not throw this electronic device into the trash when
discarding. To minimize pollution and ensure utmost protection
of the global environment, please recycle it.
6
English
Safety notice
LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT
WAVE LENGTH: 450-460 nm / MAX OUTPUT: 15.9 mW / PULSE DURATION: 1.25 ms
IEC 60825-1:2014 CLASS 1 LASER PRODUCT / RISK GROUP 2
Possibly hazardous optical radiation emitted from this product.
Do not stare into the beam, May be harmful to the eyes.
COMPLIES WITH
21 CFR 1040.10 AND
1040.11 EXCEPT FOR
DEVIATIONS PURSUANT
TO LASER NOTICE No. 50,
DATED JUNE 24, 2007.
IEC/EN 60825-1:2007
WARNING
- This product is classified as Class 2 of IEC 60825-1 : 2007 and also complies with 21 CFR 1040.10 and 1040.11
except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. IEC 60825-1:2014: CLASS 1 LASER PRODUCT - RISK GROUP 2
- Explanatory label is shown all information of laser power.
- This projector has built-in Class 4 laser module. Disassembly or modification is very dangerous and should never
be attempted.
- Any operation or adjustment not specifically instructed by the user’s guide creates the risk of hazardous laser
radiation exposure.
- Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.
- Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.
- When turning on the projector, make sure no one within projection range is looking at the lens.
- Without following the control, adjustment or operation procedure may cause damage by the exposure of laser
radiation.
- Adequate instructions for assembly, operation, and maintenance, including clear warnings concerning precautions to avoid possible exposure to laser and collateral radiation in excess of the accessible emission limits in
Class 2.
- This projector is a Class 2 laser device that conforms with IEC 60825-1:2007 and CFR 1040.10 and 1040.11.
- Class 2 laser product, Do Not Stare Into Beam.
- This projector has built-in Class 4 laser module. Disassembly or modification is very dangerous and should never
be attempted.
- Any operation or adjustment not specifically instructed by the user’s guide cre- ates the risk of hazardous laser
radiation exposure.
- Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.
- Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.
- Without following the control, adjustment or operation procedure may cause damage by the exposure of laser
radiation.
- Adequate instructions for assembly, operation, and maintenance, including clear warnings concerning precautions to avoid possible exposure to laser and collateral radiation in excess of the accessible emission limits in
Class 2.
English
7
INTRODUCTION
Package Overview
Unpack and inspect the box contents to ensure all parts listed below are in the box. If something is missing, please
contact your nearest customer service center.
Projector
AA
AA
AAA Batteries x2
Power Cord
VGA Cable
Remote Control
CD User Manual

 Warranty Card*
 Basic User Manual
Documentation
Note: * For European warranty Information, please visit www.optomaeurope.com
Due to different applications in each country, some regions may have edifferent accessories.
8
English
INTRODUCTION
Product Overview
Main Unit
1
3
5
4
2
9
6
3
8
6
10
7
11
12
13
14
3
Note: D
o not block projector inlet or outlet air vents.
No
1.
2.
3.
4.
5.
6.
7.
Item
Keypad
Focus Ring
Ventilation (inlet)
IR Receiver
Ventilation (outlet)
Speakers
Power Socket
No
8.
9.
10.
11.
12.
13.
14.
Item
Input / Output Connections
Lens
Tilt-Adjustment Foot
Kensington Lock
Lens Shift (vertical)
Lens Shift (Horizontal)
Lens lock
English
9
INTRODUCTION
Control Panel
1
2
3
4
5
8
6
9
7
No
1.
2.
3.
4.
5.
10 English
Item
On/Standby LED
Enter
Temp LED
Lamp LED
Menu
No
6.
7.
8.
9.
Item
Source
Four Directional Select Keys
Power/Standby button
IR Receiver
INTRODUCTION
Connections
F1 F2
12
11 10
9
7
6
3
2
1
4
14 15 16
8
5
13
17
No
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Item
Microphone connector
Audio In connector
VGA In/ YPbPr connector
Audio Out connector
VGA Out connector
HDMI 1connector
HDMI 2/MHL connector
RS232C connector
USB-B mini connector
USB Power Out
(5V ---1.5A) Connector
No
Item
11. HDBaseT connector (Depending
on Model)
12. RJ45
13. Power Socket
14. 3D Sync Out (5V) connector
15. Wired Remote connector
16. 12V Trigger connector
17. Kensington Lock
F1 HDMI3/MHL Connector
F2 USB Power
English 11
INTRODUCTION
Remote Control
No
1
17
Item
1.
Power On
Power on the projector.
2.
Geometric Correction
Launch the Geometric Correction menu.
3.
F1:Test pattern
Display a test pattern.
2
18
4.
Display Mode
Select the display mode.
3
19
5.
Four directional select keys
To select items or make adjustments.
4
20
6.
Information
Display the projector information.
7.
F3:Color Matching
Launch the Color Matching setting menu.
8.
Input source selection
Select an input signal.
9.
Menu
Launch the OSD menu. To exit OSD, Press
“Menu” again.
10. Volume Control -/+
Increase/decrease the volume.
11. Freeze
Freeze the projected image.
12. Format
Choose the projector format.
13. VGA
Switch to VGA source.
14. HDMI1
Switch to HDMI1 source.
21
5
22
6
7
23
8
24
9
10
11
25
12
13
26
14
27
15
28
15. HDBaseT (Depending on Model)
Switch to HDBaseT source.
16. 3D
Switch to 3D source.
17. Power Off
Power off the projector.
16
18. PIP/PBP Menu
Launch the PIP/PBP menu.
19. F2:LAN Settings
Launch the LAN Setting Menu.
Note: Some keys may have no function for models that do not support these features. I/O availability will vary depending
upon model and or SKU purchased.
12 English
INTRODUCTION
No
Item
20. AV Mute
Momentarily turns off/on the audio and video.
21. Enter
Confirm your item selection.
22. Laser
Use as laser pointer.
23. Re-Sync
Automatically synchronize the projector to the
input source.
24. Digital Room -/+
Zoom in/out the projected image.
25. Remote ID / Remote all
Set the remote control ID.
26. HDMI2
Switch to HDMI2 source.
27. HDMI3 (Dongle)
Switch to HDMI3(Dongle) source.
28. Number Keypad (0~9)
Use as numeric keypad number “0~9”.
English 13
SETUP AND INSTALLATION
Connecting Source to the Projector
Connect to Computer/Notebook
Note:
Due to the difference in applications for each country, some regions may have different accessories.
(*) Optional accessory
MOLEX
5
Router / Network Switch
E62405SP
R
10
9
1
Microphone
External
Display
Audio Output
No
1.
2.
3.
4.
5.
14 English
Item
RS232 Cable
VGA Cable
HDMI Cable
USB Cable
Audio In Cable
No
6.
7.
8.
9.
10.
Item
RJ45 Cable
Power Code
VGA Out Cable
Audio Out Cable
Microphone cable
SETUP AND INSTALLATION
Connect to Video Sources
DVD Player, Set-top Box,
HDTV receiver
6
1
2
5
Microphone
E62405SP
R
3
7
4
Audio Output
No
1.
2.
3.
4.
Note:
Item
HDMI Cable
Audio In Cable
Power Code
Audio Out Cable
No
5.
6.
7.
8.
Item
Microphone cable
RJ-45 cable (Cat5 cable)
12V DC Jack
HDMI3/MHL cable
Due to the difference in applications for each country, some regions may have different accessories.
(*) Optional accessory
English 15
SETUP AND INSTALLATION
Powering the Projector On/Off
Powering On the Projector
1. Securely connect the power cord and signal cable. When connected, the POWER/STANDBY LED will turn Red.
2. Turn on the lamp by pressing the “ ” button either on the projector or on the remote. At this moment, the
POWER/ STANDBY LED will now turn Blue. ①
The startup screen will display in approximately 6 sec- onds.
3. Turn on and connect the source that you want to display on the screen (computer, notebook, video player, etc).
The projector will detect the source automatically.
`` If you connect multiple sources at the same time, press the “INPUT” button on the control panel to switch
between inputs.
Note: When the power mode is in standby mode (power consumption < 0.5W), the VGA output/Wire remote/LAN
will be deactivated when the projector is in standby. Audio out loop-through is always active in standby mode.
HDBaseT control is always deactivated in standby mode.
1
POWER/STANDBY
Note: Turn on the projector first and then select the signal sources.
16 English
SETUP AND INSTALLATION
Powering off the projector
1. Press the “ ” button on the remote control or on the control panel to turn off the projector.
The following message will be displayed on the screen.
Press the “ ” button again to confirm otherwise the message will disappear after 10 seconds. When you press
the “ ” button for the second time, the fan will start cooling the system and will shut down.
2. The cooling fans continue to operate for about 4 seconds for cooling cycle and the POWER/STANDBY LED will
flash Red. When the POWER/STANDBY LED lights solid Red, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply press “ ” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and the projector.
Warning Indicator
LED lightning messages
When the warning indicators (see below) come on, the projector will automatically shutdown:
 “LAMP” LED indicator is lit red and/or if “TEMP” LED indicator is lit red.
 “TEMP” LED indicator is lit red, this indicates the projector has overheated. Under normal conditions, the projec­
tor can be switched back on.
 “TEMP” LED indicator flashes red.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up again,
please contact your nearest service center for assistance.
Message
Power LED
Temp LED
Lamp LED
Red
Red
Error(PowerGood NG)
On
On
Error (Fan fail)
Flashing
Error (Over Temp)
On
Red
Standby State (LAN Off)
On
Standby State (LAN On)
On
Error (LD fail)
On
On
Power On
Warning Up
Blue
Flashing
On
English 17
SETUP AND INSTALLATION
Adjusting the Projected Image
Adjusting the Projector�s Height
The projector is equipped with elevator feet for adjusting the image height.
1. Locate the adjustable foot you wish to modify on the underside of the projector.
2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise to lower it. Repeat with the
remaining feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
18 English
SETUP AND INSTALLATION
Adjusting Projector Focus and Zoom
1. To adjust the image size, turn the zoom ring clockwise or anticlockwise to increase or decrease the projected
image size.
2. To adjust the focus, turn the focus ring clockwise or anticlockwise until the image is sharp and legible.
The projector will focus at distances (lens to wall) from 4.27 ~ 25.59 feet (1.3-7.8 meters).
Zoom
Vertical lens shift
Focus
Front side door
Lens Lock
Horizontal lens shift
Adjusting Projection Image Size (Diagonal)
Projection Image Size from 36” to 300” (1.09~9.09 meters).
1. Open the front side door of the projector.
2. Unlock the lens lock, before adjust the lens shift.
3. Turn the vertical/horizontal lens shift knob to shift the lens
4. Turn the lens lock clockwise to lock the lens in place
( Lens shift knob still can be rotated.)
5. Close the front side door of the projector.
Note: T
he stroke for lens shift is designed to be regular triangle, when lens are adjusted to central position horizontally, lens can be vertically shifted to the highest point
Top
Top View
View
Screen
Screen (W)
Height
Projection Distance (D)
Screen
Screen (H)
Di
ag
on
al
Width
Side View
Offset (Hd)
Projection Distance (D)
English 19
SETUP AND INSTALLATION
Width
Height
10%
10%
Lens shift position
20%
20%
(Hd)
center of lens
(D)
Image Offset
image size
Screen Size WxH
inch
Diagonal
WUXGA 16:10
cm
Width
Height
Width
Height
cm
Offset (Hd)
inch
cm
Wide
Tele
Wide
Tele
NA
170.0
NA
Wide
inch
Tele
Wide Tele
36"
78.0
49.0
30.7
19.3
66.9
20.1
20.1
7.9
7.9
100"
215.0
135.0
84.6
53.1
260.0 460.0 102.4 181.1
37.4
37.4
14.7
14.7
150"
323.0
202.0
127.2
79.5
390.0 690.0 153.5 271.7
50.8
50.8
20.0
20.0
200"
431.0
269.0
169.7
105.9
520.0 920.0 204.7 362.2
64.3
64.3
25.3
25.3
250"
539.0
337.0
212.2
132.7
640.0
NA
252.0
NA
77.8
77.8
30.6
30.6
300"
646.0
404.0
254.3
159.1
770.0
NA
303.1
NA
91.2
91.2
35.9
35.9
 This table is for user’s reference only.
20 English
Projection Distance (D)
inch
USER CONTROLS
Using the Control Panel
Description
Name
POWER
Refer to the “Power On/Off the Projector” section on pages 1617.
Enter
Confirm a selected item.
INPUT
Select an input signal
Four Directional
Select Keys
Launch the on-screen display (OSD) menu. To exit OSD, press
“MENU” again.
Use ▲▼◄► to select items or make adjustments to your selection.
LAMP LED
Refer to the LED indicator of the projector light source status.
TEMP LED
Refer to the LED indicator of the projector temperature status.
ON/STANDBY
LED
Refer to the LED indicator of the projector power status.
MENU
English 21
USER CONTROLS
On-screen Display Menus
The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a
variety of settings.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or Projector Keypad.
2. When OSD is displayed, use ▲▼ keys to select any item in the main menu. While making a selection on a
particular page, press the ► or “Enter” key to enter sub menu.
3. Use the ▲▼ keys to select the desired item and adjust the settings using the ◄► key.
4. Select the next item to be adjusted in the sub menu and adjust as described above.
5. Press “Enter” to confirm.
6. To exit, press “Menu” again. The OSD menu will close and the projector will automatically save the new settings.
Main Menu
Sub Menu
22 English
Settings
USER CONTROLS
Structure
Note: Please note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model you are using.
Main Menu Sub Menu
Setting
Bright/Presentation/Movie/sRGB/Blending/DICOM SIM./User
Color Mode
(Change Color Mode to User Mode if customer changes the
settings)
Wall Color
White/ Light Yellow/ Light Blue/ Pink/ Dark Green
Brightness
Contrast
Sharpness
Picture
Saturation
(For VGA component signal only)
Hue
(VGA component signal only)
Gamma
Film/Graphics/1.8/2.0/2.2/2.6/Blackboard/DICOM SIM
Color Temp
5500K/6500K/7500K/8500K/9500K
Color Matching
White/Red/
Green/Blue/Cyan/ Hue/ Saturation /Gain
Magenta/Yellow
Dynamic Black
On / Off
Not HDMI Input: Auto/RGB/YUV
Color Space
HDMI Input: Auto/RGB(0~255)/RGB(16~235)/YUV
Aspect Ratio
Auto/4:3/16:9/16:10
Phase
Clock
H.Position
V.Position
Digtial Zoom
Projection
Front/Front Ceiling/Rear/Rear Ceiling
V. Keystone
Screen
Geometric
Correction
H. Keystone
4 Corners
On/Off
Grid Color
Purple/Green
Reset
Function
PIP-PBP Settings
Yes/No
PBP/PIP/ Off
Main Source
VGA/HDMI-1/HDMI-2/Dongle/HDBaseT
Sub Source
VGA/HDMI-1/HDMI-2/Dongle/HDBaseT
Location
Size
Top Left/Top Right/Bottom Left/Bottom Right
Small/Medium/Large
Swap
English 23
USER CONTROLS
Main Menu Sub Menu
Settings
Volume
Language
English/German/French/Italian/Spanish/Polish/Swedish/
Dutch/Portugese/Japanese/Traditional Chinese/ Simplified
Chinese /Korean/Russian/Arabic/Norsk/Turkish/Danish/
Finnish/Greek/Hungarian/Czech/Romania/Thai/Farsi/Vietnam
/Indonesian/Slovakian
Menu Location
Left Top, Right Top, Center, Left Bottom, Right Bottom
VGA OUT
(Standby)
Off/On
LAN (Standby)
Off/On
Test Pattern
None / Grid / White
Direct Power On
On/Off
Reset to Default
Yes/No
Speaker
On/Off
Audio Out
On/Off
Microphone
On/Off
Mute
On/Off
Volume
Microphone
Volume
EQ
24 English
Setting
USER CONTROLS
Main Menu Sub Menu
Setting
Logo
Default/User
Logo Capture
Auto Source
On/Off
Input
VGA, HDMI-1, HDMI-2, Dongle, HDBaseT
Auto Power Off
(Min.)
Sleep Timer (Min.)
SSI Hours Used (Normal)
SSI Settings
SSI Hours Used (ECO)
SSI Power Mode Normal,ECO
High Altitude
On/Off
Optional Filter
Installed
Optional Filter
Settings
Security
Options
Remote Settings
HDBaseT Control
Filter Usage
Hours
[Default Off]
Yes/No
Read-Only
Filter Reminder
Cleaning Up
Reminder
Yes/No
Security
On / Off
Security Timer
Month / Day / Hour
Change
Password
IR Function
On / Off
Remote Code
00 ~ 99
Auto
HDBaseT
Version
HDMI EQ
PIP-PBP Module
Reset
USB Upgrade
Information Hide
On / Off
Model Name
SNID
Source (Main Source / Sub Source)
Main Source Resolution
Sub Source Resolution
Information
SW Version (DDP/MCU/LAN)
Aspect Ratio
SSI Hours (Normal/Eco)
IP Address
Network Status
Remote Code
Remote Code (Active)
English 25
USER CONTROLS
Main Menu Sub Menu
Setting
3D
Auto/On
3D Invert
On/Off
Frame Packing
3D
Side-by-Side (Half)
3D Format
Top amd Bottom
Frame Sequential
Field Sequential
1080p @ 24
96Hz/144Hz
Status
DHCP Client
IP Address
Subnet Mask
Gateway
Network
DNS
Store
MAC Address
Group Name
Projector Name
Location
Contact
26 English
On/Off
USER CONTROLS
Picture
Color Mode
There are many factory presets optimized for various types of images. Use the ◄ or ► button to select the item.
••
••
••
••
••
••
••
Bright: For brightness optimization.
Presentation: For meeting presentation.
Movie: For playing video content.
sRGB: For game content.
Blending: For blending application.
DICOM Sim:
User: Memorize user’s settings.
Wall Color
Use this function to obtain an optimized screen image according to the wall color. You can select from “White”, “Light
Yellow”, “Light Blue”, “Pink”, and “Dark Green”.
Brightness
Adjust the brightness of the image.
•• Press the ◄ button to darken image.
•• Press the ► button to brighten image.
Contrast
The Contrast controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast
changes the amount of black and white in the image.
•• Press the ◄ button to decrease the contrast.
•• Press the ► button to increase the contrast.
Sharpness
Adjust the sharpness of the image.
•• Press the ◄ button to decrease the sharpness.
•• Press the ► button to increase the sharpness.
Note: “Sharpness”, “Sat- uration” and “Hue” functions are only supported under video mode.
English 27
USER CONTROLS
Saturation
Adjust a video image from black and white to fully saturated color.
•• Press the ◄ button to decrease the amount of saturation in the image.
•• Press the ► button to increase the amount of saturation in the image.
Hue
Adjust the color balance of red and green.
•• Press the ◄ button to increase the amount of green in the image.
•• Press the ► button to increase the amount of red in the image.
Gamma
This allows you to adjust the gamma value to obtain the better image contrast for the input.
Color Temp
This allows you to adjust the color temperature. At higher temperature, the screen looks colder; at lower
temperature, the screen looks warmer.
Color Maching
Use these settings for advanced adjustment of the individual Red,Green,Blue,Cyan,Magenta and Yellow and White
Colors.
Dynamic Black
Use this function to increase the contrast ratio.
Color Space
Select an appropriate color matrix type from AUTO, RGB, RGB(0-255), RGB(16-235) or YUV.
Note: “RGB (0-255)” and “RGB (16-235)” are only supported for HDMI source.
28 English
USER CONTROLS
Screen
Aspect Ratio
•• Auto: Keep the image with original width-height ratio and maximize the image to fit native horizontal or
vertical pixels.
•• 4:3: The image will be scaled to fit the screen and displayed using a 4:3 ratio.
•• 16:9: The image will be scaled to fit the width of the screen and the height adjusted to display the image
using a 16:9 ratio.
•• 16:10: The image will be scaled to fit the width of the screen and the height adjusted to display the image
using a 16:10 ratio.
Phase
Synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or flickers,
use this function to correct it.
Note: Phase, Clock, H. Position, V. Position adjustment only support VGA Graphic.
Clock
Adjust to achieve an optimal image when there is a vertical flicker in the image.
H. Position
•• Press the ◄ button to move the image left.
•• Press the ► button to move the image right.
V. Position
•• Press the ◄ button to move the image down.
•• Press the ► button to move the image up.
Digital Zoom
•• Press the ◄ button to reduce the size of an image.
•• Press the ► button to magnify an image on the projection screen.
English 29
USER CONTROLS
Projection
••
••
••
••
Front: The image is projected straight on the screen.
Front Ceiling: This is the default selection. When selected, the image will turn upside down.
Rear: When selected, the image will appear reversed.
Rear Ceiling: When selected, the image will appear reversed in upside down position.
Geometric Correction
•• H Keystone
Press the ◄ or ► button to adjust image distortion horizontal. If the image looks trapezoidal, this option can
help make the image rectangular.
•• V Keystone
Press the ◄ or ► button to adjust image distortion vertically. If the image looks trapezoidal, this option can
help make the image rectangular.
•• 4 Corners
Adjust the image 4 corners pixel by pixel to make the image rectan- gular.
•• Grid Color
Set 4 corners correction function grid color.
•• Reset
Set H/V Keystone, 4 corners parameters to default values.
PIP-PBP Settings
••
••
••
••
••
••
Function: To enable/disable PIP/PBP function.
Main Source: To set PIP/PBP main source.
SUb Source: To set PIP/PBP sub source.
Location: To set PIP sub source location.
Size: To set PIP sub source size.
Swap: To swap PIP/PBP main/sub source.
Some source/signal combinations may not be compatible with PIP/PBP function. Please refer to the table below:
Matrix
HDMI-1
HDMI-2
Dongle
HDBaseT
VGA
HDMI-1
-
V
V
-
V
HDMI-2
V
-
-
V
V
Dongle
V
-
-
V
V
HDBaseT
-
V
V
-
V
VGA
V
V
V
V
-
1. Flashing lines may occur if the bandwidth of both inputs are too high, please try to reduce the resolution.
2. Frame tearing may occur due to a difference in frame rate between the Main and the Sub picture, please try to
match the frame rate for each input.
30 English
USER CONTROLS
Settings
Language
Choose the multilingual OSD menu. Press the ◄ or ► button into the sub menu and then use the ▲ or ▼ button to
select your preferred language. Press ► on the remote control to finalize the selection.
Menu Location
Choose the menu location on the display screen.
VGA Output (Standby)
Choose “On” to enable VGA OUT connection.
LAN (Standby)
Choose “On” to enable LAN connection. Choose “Off” to disable LAN connection.
Test Pattern
Display a test pattern.
Direct Power On
Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied,
without pressing the key on the projector control panel or on the remote control.
Reset
Choose “Yes” to return the parameters on all menus to the factory default settings.
English 31
USER CONTROLS
Volume
Speaker
•• Choose “On” to enable the speaker.
•• Choose “Off” to disable the speaker.
Line Out
•• Choose “On” to enable the line out function.
•• Choose “Off” to disable the line out function.
Microphone
•• Choose “On” to enable the microphone.
•• Choose “Off” to disable the microphone.
Mute
•• Choose “On” to turn mute on.
•• Choose “Off” to turn mute off.
Volume
•• Press the ◄ button to decrease the volume.
•• Press the ► button to increase the volume.
Microphone Volume
•• Press the ◄ button to decrease the microphone volume.
•• Press the ► button to increase the microphone volume.
EQ
Set audio EQ values.
32 English
USER CONTROLS
Options
Logo
Use this function to set the desired startup screen. If changes are made they will take effect the next time the
projector is powered on.
•• Default: The default startup screen.
•• User: Use stored picture from “Logo Capture” function.
Logo Capture
Press ► button to capture an image of the picture currently displayed on screen.
Note:
For successful logo capture, please ensure that the on-screen image does not exceed the projector’s native
resolution.
“Logo Capture” is not available when 3D is enabled.
Before active this function, it is recommended that “Aspect Ratio” is set to the “Auto”.
Auto Source
•• On: The projector will search for other signals if the current input signal is lost.
•• Off: The projector will only search current input connection.
Input
Press ► button to enable/disable input sources. The projector will not search for inputs that are not selected.
Auto Power Off (Min)
Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the
projector. The projector will automatically power off when the countdown has finished (in minutes).
English 33
USER CONTROLS
Sleep Timer
Sets the countdown timer. The countdown timer will start, with or without a signal being sent to the projector. The
projector will automatically power off when the countdown has finished (in minutes).
SSI Settings
•• SSI Hours Used (Normal)
Display the projection time of normal mode.
•• SSI Hours Used (ECO)
Display the projection time of ECO mode.
•• SSI Power Mode
Normal: Normal mode.
ECO: Use this function to dim the projector SSI which will lower power consumption and extend the SSI life.
High Altitude
•• On: The built-in fans run at high speed. Select this option when using the projector at altitudes above 2500
feet/762 meters or higher.
•• Off: The built-in fans automatically run at a variable speed according to the internal temperature.
Optional Filters Remind (Hour)
••
••
••
••
Optional Filter Installed: Filter is installed or not.
Filter Usage Hours: Hours of filter had been used.
Filters Remind (Hour): Set the filter reminder time.
Cleaning Up Remind: Select “Yes” to reset the dust filter hour counter after replacing or cleaning the dust
filter.
Security
•• Security: Choose “On” to use security verification when turning on projector. Choose “Off” to be able to
switch on the projector without password verification.
•• Security Timer
Use this function to set the how long (Month/Day/Hour) the projector can be used. Once this time has
elapsed you will be requested to enter your password again.
•• Change Password
First time:
1. Press “ ” to set the password.
2. The password has to be 6 digits.
3. Use number button on the remote to enter your new password and then press “ ” key to confirm your
password.
Change Password:
1. Press “ ” to input old password.
2. Use number button to enter current password and then press “ ” to confirm.
3. Enter new password (6 digits in length) using the number buttons on the remote, then press “ ” to
confirm.
4. Enter new password again and press “ ” to confirm.
•• If the incorrect password is entered 3 times, the projector will automatically shut down.
•• If you have forgotten your password, please contact the dealer for support.
34 English
USER CONTROLS
Note:
Password default value is “000000” (first time).
Always keep the password in your files. If the password is forgotten or lost, please contact your local authorized service center.
Remote Setting
 IR function: When this function is “Off”, the projector cannot be operated by the remote control.
 Remote code: 00~99, default code (common code): 00
HDBaseT Control
•
The projector will automatically detect the signal from HDBaseT transmitter supplied. Choose “HDBaseT” to
activate Direct Power mode.
•
When HDBaseT control is ON, 12v trigger output signal will always be ON, even if the
projector is on Standby mode.
PIP-PBP Module
•
•
•
•
Version: Show PIP-PBP module software version.
Reset: Reset the PIP-PBP module.
USB Upgrade: Upgrade the PIP-PBP module software.
HDMI EQ: Set PIP-PBP module HDMI port EQ value.
Information Hide
•
•
On: Choose “On” to hide the info message.
Off: Choose “Off” to show the “info” message.
Information
Display the projector information for model name, SNID, source, resolution, software version, aspect ratio, SSI
Hours, IP Address and Network Status on the screen.
Signal Power On & HDBaseT Standby
To access Signal Power On and HDBaseT Standby menu -- with projector on press the following buttons (in order):
Power > Up >Down> Menu.
Signal Power On
• On: Choose “On” to enable Signal Power On.
• Off: Choose “Off” to disable Signal Power On.
HDBaseT Standby
• On: Choose “On” to enable HDBaseT Standby.
• Off: Choose “Off” to disable HDBaseT Standby.
English 35
USER CONTROLS
3D
3D
Auto: When a HDMI 1.4a 3D timing identification signal is detected, the 3D image is selected automatically.
•• Choose “On” to enable 3D function.
•• Choose"Auto" to detected 3D signal automatically.
3D Invert
If you see a discrete or overlapping image while wearing DLP 3D glasses, you may need to execute “Invert” to get
best match of left/right image sequence to get the correct image.
3D Format
Use this feature to select the 3D format. Options are: “Frame Packing”, “Side-by-Side (Half)”, “Top and Bottom”,
“Frame Sequential”.
[email protected]
Use this feature to select 96 or 144Hz refresh rate as using 3D glasses in the1080p @ 24 frame packing.
36 English
USER CONTROLS
LAN
Status
Display the network connection status.
DHCP
Configure the DHCP settings.
•• On: Choose “On” to let the projector to obtain an IP address automatically from your network.
•• Off: Choose “Off” to assign IP, Subnet Mask, Gateway, and DNS configuration manually.
IP Address
Display an IP address.
Subnet Mask
Display the subnet mask number.
Gateway
Display the default gateway of the network connected to the projector.
DNS
Display the DNS number.
MAC Address
Display the MAC address.
Group Name
Display the group name.
Projector Name
Display the projector name.
Location
Display the projector location.
Contact
Display the contact information.
English 37
APPENDICES
Projector Problems
The projector stops responding to all controls
`` If possible, turn off the projector, then unplug the power cord and wait at least 60 seconds before reconnecting power.
`` Check that “Keypad Lock” is not activated by trying to control the projector with the remote control.
If the remote control does not work
`` Check if the operating angle of the remote control is within ±30° both
horizontally and vertically on one of the IR receivers on the projector.
`` Make sure there is no obstruction between the remote control and the projector. Move to within 12 m (±0°)
of the projector.
`` Make sure the batteries are inserted correctly.
`` Replace batteries if they are exhausted.
`` Ensure that you have set your remote to the correct IR code setting.
When making a direct connection from your computer to the projector
`` If you have network connection problem from your computer to the projector, please refer to the computer
setting as below or contact with web administrator.
Step 1: Find an IP Address (192.168.0.100) from LAN function of projector.
Step 2: Select “Apply” and push the “Enter” button. Once the setting is saved, exit the OSD by pushing
“Menu” button.
Step 3: To open Network Connections, click Start, click Control Panel, click Network and Internet
Connections, and then click Network Connections. Click the connection you want to configure, and
, click Change settings of this connection.
then, under Network Tasks
Step 4: On the General tab, under This connection use the following items, click Internet Protocol(TCP/
IP), and then click “Properties”.
38 English
APPENDICES
Step 5: Click Use the following IP address, and type in as below:
1) IP address: 192.168.0.101
2) Subnet mask: 255.255.255.0
3) Default gateway: 192.168.0.254
Step 6: To open Internet Options, click IE web browser, click Internet Options, click the Connections tab
and click “LAN Setting…”.
Step 7: All items in the Local Area Network (LAN) Setting window must unchecked. Then click “OK” button
twice.
Step 8: Open your IE and type in the IP address of 192.168.0.100 in the URL then press “Enter” key.
English 39
APPENDICES
How to use web browser to control your projector
1. Turn on DHCP to allow a DHCP server to automatically assign an IP, or manually enter the required network
information.
2. Then choose apply and press
button to complete the configuration process.
3. Open your web browser and type in IP Address from the OSD LAN screen then the web page will display as
below:
Note: When you used the projector IP address, you will can not link to your service server.
4. Based on network web-page for the input-string in [tools] tab, the limitation for Input-Length is in the below list
(“space” and the other punctuation key included):
Category
Crestron Control
Projector
Network
Configuration
User Password
Admin Password
40 English
Item
IP Address
IP ID
Port
Projector Name
Location
Assigned To
DHCP (Enabled)
IP Address
Subnet Mask
Default Gateway
DNS Server
Enabled
New Password
Confirm
Enabled
New Password
Confirm
Input-Length
(characters)
15
2
5
10
9
9
(N/A)
15
15
15
15
(N/A)
15
15
(N/A)
15
15
APPENDICES
Crestron RoomView Control Tool
Crestron RoomView™ provides a central monitoring station for 250+ control systems on a single Ethernet network
(more are possible, the number depends on the combination of IP ID and IP address). Crestron RoomView
monitors each projector, including projector’s online status, system power, lamp life, network setting and hardware
faults, plus any custom attribute as defined by the Administrator.
The Administrator can add, delete, or edit room information, contact information and events, which are logged automatically by the software for all users. (Operation UI as following image)
Note: Crestron RoomView function support is dependent on models.
When using RS232 or LAN control commands to power on the
projector, there will be a feedback delay of 6 to 10 seconds.
1. Main Screen
2. Edit Room
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s on-screen display
(OSD) menu, and “02” for IPID, “41794” for the reserved Crestron control port.
About Crestron RoomView™ setting and command method, please access below website to get RoomView™
User Guide and more information:
http://www.crestron.com
English 41
APPENDICES
3. Edit Attribute
4. Edit Event
For more information, please visit
http://www.crestron.com & www.crestron.com/getroomview.
Network supports Crestron (Room View), AMX (Device Discovery) , PJLink and RS232 control.
42 English
APPENDICES
Installing and Cleaning the Optional Dust Filter
We recommend you clean the dust filter every 500 hours of operation, or more often if you are using the projector
in a dusty environment.
When the warning message appears on the screen, do the following to clean the air filter:
Note:
The optional dust filter should be used in dusty environments.
If the dust filter is installed, a proper maintenance will prevent overheat- ing and projector malfunction.
The dust filter is optional.
The specific inter- faces are selected in terms of the specifications of types.
1
2
3
Air Filter Cleaning Procedure:
1. Switch off the power to the projector by pressing the “ ” button.
2. Disconnect the power cord.
3. Pull out the dust filter, as shown in the illustration.①
4. Carefully remove the dust filter. Then clean or change the filter. ②
To install the filter, reverse the previous steps.
5. Turn on the projector and reset the filter usage counter after the dust filter is
replaced.
English 43
APPENDICES
Compatibility Modes
A. VGA Analog
(1) PC Signal
Modes
Resolution
V.Frequency
[Hz]
H.Frequency
[KHz]
Pixel CLK
VGA
640x480
60
31.5
25,2
Established Timings 1
640x480
67
35.0
26.8
Established Timings 1
640x480
72
37.9
31.5
Established Timings 1
640x480
75
37.5
31.5
Established Timings 1
640x480
85
43.3
36.0
IBM
720x400
70
31.5
28.3
Established Timings 1
SVGA
800x600
56
35.1
36.0
Established Timings 1
800x600
60
37.9
40.0
Established Timings 1
800x600
72
48.1
50.0
Established Timings 2
800x600
75
46.9
49.5
Established Timings 2
800x600
85
53.7
56.3
832x624
75
49.1
57.3
Apple, Mac II
[MHz]
EDID Description
Established Timings 2
WXGA: Established Timings 2
XGA
XGA: Established Timings 2
1024x768
60
48.4
65.0
1024x768
70
56.5
75.0
Established Timings 2
1024x768
75
60.0
78.8
Established Timings 2
1024x768
85
68.7
94.5
and (Native)Detailed Timing / Descriptor Block 1
1024x768
120
99.0
137.8
Standard Timing Identification
Apple, Mac II
1152x870
75
68.7
100.0
Manufacturer’s Reserved Timing
SXGA
1280x1024
60
64.0
108.0
1280x1024
72
77.0
133.0
1280x1024
75
80.0
135.0
Established Timings 2
QuadVGA
1280x960
60
60.0
101.3
Standard Timing Identification
1280x960
75
75.2
130.0
SXGA+
1400x1050
60
65.3
121.8
UXGA
1600x1200
60
75.0
161.0
Full HD
1920x1080
60
67.5
148.5
WUXGA
1920x1200
60
74
154
Reduced Blanking
Standard Timing Identification
(2) Extended Wide timing
WXGA
WSXGA+
1280x720
60
44.8
74.2
Standard Timing Identification
1280x800
60
49.6
83.5
WXGA: (Native)Detailed Timing / Descriptor Block 1
XGA: Standard Timing Identification
1366x768
60
47.7
84.8
1440x900
60
59.9
106.5
1680x1050
60
65.3
146.3
60
44.35
92.25
1920x720
(3) Component Signal
480i
44 English
720x480
(1440x480)
59.94(29.97)
15.7
13.5
Standard Timing Identification
WXGA: Standard Timing Identification
XGA: N/A
APPENDICES
576i
720x576
(1440x576)
50(25)
15.6
13.5
480p
720x480
59.94
31.5
27.0
576p
720x576
50
31.3
27.0
720p
1280x720
60
45.0
74.25
720p
1280x720
50
37.5
74.25
1080i
1920x1080
60(30)
33.8
74.25
1080i
1920x1080
50(25)
28.1
74.25
1080p
1920x1080
23.98/24
27.0
74.25
1080p
1920x1080
60
67.5
148.5
1080p
1920x1080
50
56.3
148.5
B. HDMI Digital
(1) PC Signal
Modes
Resolution
V.Frequency
[Hz]
H.Frequency
[KHz]
Pixel CLK
VGA
640x480
60
31.5
25,2
Established Timings 1
640x480
67
35.0
26.8
Established Timings 1
640x480
72
37.9
31.5
Established Timings 1
640x480
75
37.5
31.5
Established Timings 1
[MHz]
EDID Description
640x480
85
43.3
36.0
IBM
720x400
70
31.5
28.3
Established Timings 1
SVGA
800x600
56
35.1
36.0
Established Timings 1
800x600
60
37.9
40.0
Established Timings 1
800x600
72
48.1
50.0
Established Timings 2
800x600
75
46.9
49.5
Established Timings 2
800x600
85
53.7
56.3
832x624
75
49.1
57.3
Apple, Mac II
Established Timings 2
WXGA: Established Timings 2
XGA
XGA: Established Timings 2
1024x768
60
48.4
65.0
1024x768
70
56.5
75.0
Established Timings 2
1024x768
75
60.0
78.8
Established Timings 2
1024x768
85
68.7
94.5
1024x768
120
99.0
137.8
Standard Timing Identification
Apple, Mac II
1152x870
75
68.7
100.0
Manufacturer’s Reserved Timing
SXGA
1280x1024
60
64.0
108.0
1280x1024
72
77.0
133.0
1280x1024
75
80.0
135.0
Established Timings 2
1280x960
60
60.0
101.3
Standard Timing Identification
1280x960
75
75.2
130.0
SXGA+
1400x1050
60
65.3
121.8
UXGA
1600x1200
60
75.0
161.0
Full HD
1920x1080
60
67.5
148.5
WUXGA
1920x1200
60
74
154
QuadVGA
and (Native)Detailed Timing / Descriptor Block 1
Standard Timing Identification
Reduced Blanking
(2) Extended Wide timing
English 45
APPENDICES
WXGA
WSXGA+
1280x720
60
44.8
74.2
Standard Timing Identification
1280x800
60
49.6
83.5
WXGA: (Native)Detailed Timing / Descriptor Block 1
XGA: Standard Timing Identification
1366x768
60
47.7
84.8
1440x900
60
59.9
106.5
1680x1050
60
65.3
146.3
1920x720
60
44.35
92.25
Standard Timing Identification
WXGA: Standard Timing Identification
XGA: N/A
(3) HDMI - Video Signal
640x480p
640x480
59.94/60
31.5
25.2
Short Video Descriptor of CEA EDID
Timing
480i
720x480
(1440x480)
59.94(29.97)
15.7
13.5
Short Video Descriptor of CEA EDID
Timing
576i
720x576
(1440x576)
50(25)
15.6
13.5
Short Video Descriptor of CEA EDID
Timing
480p
720x480
59.94
31.5
27.0
Short Video Descriptor of CEA EDID
Timing
576p
720x576
50
31.3
27.0
Short Video Descriptor of CEA EDID
Timing
720p
1280x720
60
45.0
74.25
(Native)Short Video Descriptor of CEA
EDID Timing
720p
1280x720
50
37.5
74.25
(Native)Short Video Descriptor of CEA
EDID Timing
1080i
1920x1080
60(30)
33.8
74.25
Short Video Descriptor of CEA EDID
Timing
1080i
1920x1080
50(25)
28.1
74.25
Short Video Descriptor of CEA EDID
Timing
1080p
1920x1080
23.98/24
27.0
74.25
Short Video Descriptor of CEA EDID
Timing
1080p
1920x1080
60
67.5
148.5
Short Video Descriptor of CEA EDID
Timing
1080p
1920x1080
50
56.3
148.5
Short Video Descriptor of CEA EDID
Timing
(4) HDMI 1.4a mandatory 3D timing- Video Signal
Frame Packing
Top-and-Bottom
720p
50
75
148.5
Short Video Descriptor of CEA EDID
Timing
720p
59.94/60
90
148.5
Short Video Descriptor of CEA EDID
Timing
1080p
23.98/24
54
148.5
Short Video Descriptor of CEA EDID
Timing
720p
50
37.5
74.25
Short Video Descriptor of CEA EDID
Timing
720p
59.94/60
45.0
74.25
Short Video Descriptor of CEA EDID
Timing
1080p
23.98/24
27.0
74.25
Short Video Descriptor of CEA EDID
Timing
(5) Input signal frequency range
Analog: fh=15kHz~100kHz, fv=24Hz~120Hz, Max. pixel rate: 162.5MHz
Digital (HDMI): fh=15kHz~100kHz, fv=24Hz~120Hz, Max. pixel rate: 200MHz
46 English
APPENDICES
Ceiling Mount Installation
1. To prevent damage to your projector, please use the Optoma ceiling mount.
2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications:
• Screw type: M4*4
• Minimum screw length: 14mm
Note: Please note that damage resulting from incorrect installation will void the warranty.
Warning:
1. If you buy a ceiling mount from another company, please be sure to use the correct screw size. Screw size
will vary depending on the thickness of the mounting plate.
2. Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.
3. Avoid installing the projector near a heat source.
English 47
APPENDICES
Optoma global offices
For service or support, please contact your local office.
USA
3178 Laurelview Ct.
Fremont, CA 94538, USA
www.optomausa.com
Canada
3178 Laurelview Ct.
Fremont, CA 94538, USA
www.optomausa.com
888-289-6786
510-897-8601
[email protected]
888-289-6786
510-897-8601
[email protected]
Latin America
3178 Laurelview Ct.
Fremont, CA 94538, USA
www.optomausa.com
888-289-6786
510-897-8601
[email protected]
Europe
42 Caxton Way, The Watford Business Park
Watford, Hertfordshire,
WD18 8QZ, UK
+44 (0) 1923 691 800
www.optoma.eu
+44 (0) 1923 691 888
Service Tel : +44 (0)1923 691865
[email protected]
Benelux BV
Randstad 22-123
1316 BW Almere
The Netherlands
www.optoma.nl
France
Bâtiment E
81-83 avenue Edouard Vaillant
92100 Boulogne Billancourt,
France
Spain
C/ José Hierro,36 Of. 1C
28522 Rivas VaciaMadrid,
Spain
Deutschland
Wiesenstrasse 21 W
D40549 Düsseldorf,
Germany
48 English
+31 (0) 36 820 0252
+31 (0) 36 548 9052
+33 1 41 46 12 20
+33 1 41 46 94 35
[email protected]
+34 91 499 06 06
+34 91 670 08 32
+49 (0) 211 506 6670
+49 (0) 211 506 66799
[email protected]
Scandinavia
Lerpeveien 25
3040 Drammen
Norway
+47 32 98 89 90
+47 32 98 89 99
[email protected]
PO.BOX 9515
3038 Drammen
Norway
Korea
WOOMI TECH.CO.,LTD.
4F,Minu Bldg.33-14, Kangnam-Ku,
seoul,135-815, KOREA
+82+2+34430004
+82+2+34430005
Japan
東京都足立区綾瀬3-25-18
株式会社オーエス
コンタクトセンター:0120-380-495
[email protected]
www.os-worldwide.com
Taiwan
12F., No. 213,Sec. 3, Beixin Rd.,
+886-2-8911-8600
Xindian Dist., New Taipei City 231,
+886-2-8911-6550
Taiwan, R.O.C.
[email protected]
www.optoma.com.tw
asia.optoma.com
Hong Kong
Unit A, 27/F Dragon Centre,
79 Wing Hong Street,
Cheung Sha Wan,
Kowloon, Hong Kong
China
5F, No. 1205, Kaixuan Rd.,
Changning District
Shanghai, 200052, China
+852-2396-8968
+852-2370-1222
www.optoma.com.hk
+86-21-62947376
+86-21-62947375
www.optoma.com.cn
www.optoma.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement