Yealink Yealink DECT IP Multi-Cell Base Station W80B Quick start guide

advertisement

Yealink Yealink DECT IP Multi-Cell Base Station W80B Quick start guide
DECT IP Multi-Cell Base Station
W80B
Quick Start Guide(V83.30)
www.yealink.com
For W80B firmware 103.83.0.10 or later
For W53H firmware 88.83.0.20 or later
For W56H firmware 61.83.0.20 or later
Package Contents
+ +
2
2
Quick Start Guide
Expansion Screws
W80B Base Station
Power Adapter
(Optional)
Installation
Packaging Contents
1. Connect the power and the network using method a or method b.
a. AC Power Option
b. PoE (Power over Ethernet) Option
IEEE 802.3af compliant
PoE Hub/Switch
Note:
If you choose method a, use Yealink supplied power adapter (5V/1.2A).
A third-party power adapter may damage the base station.
If you choose method b, you do not need to connect the power adapter.
Make sure the hub/switch is PoE-compliant.
2. Mount W80B on the wall or on the ceiling.
MAC
MA
C
SN
SN
A
59m
m
59m
SN
59mm
B
30 mm
25 mm
MAC
m
Max:8mm
(0.315”)
Min:6.5mm
(0.256”)
Max:4.5mm
(0.177”)
Max:3mm
(0.118”)
Wall-Mount Installation
1
59mm
3 mm
C
Ceiling Installation
Note: When attaching the base station, we recommend that you make the screws protrude by
approximate 3 mm.
Assigning a Device Role
The W80B is shipped as a base station. Before registering a handset to the W80B, you
need to switch the W80B to the DM-Base role. Then, the W80B can work as a DECT
Manager and base station.
Switching to the DM-Base Role
Easy Switch:
1. Press
on the W80B three times quickly in one second.
Normal Switch:
1. Long press
on the W80B for about 10 seconds till the three LED indicators slowly
flash green.
2. Press
three times briefly.
The ROLE LED indicator glows orange, and the DECT and LAN LED indicators glow
green. The device will reboot to make the change take effect.
Note: When you change the base mode, the time interval between each button press should
be less than 3 seconds. The device will return to the original mode after 30 seconds of
inactivity.
Base Mode Options
The following shows the LED status after the W80B connects to the power and
network:
Base Mode
Role
DECT LED
ROLE LED
1
Base
Off
Green
Green
2
DM
Off
Orange
Green
3
DM-Base
Green
Orange
Green
Option
2
LAN LED
Registering the Handset
Before registering, long press
on the W80B till the DECT LED indicator flashes. You
can only register one handset to the W80B using this method.
If the W56H/W53H handset LCD screen prompts “Unregistered!”, there are two
methods to register a new handset:
Easy Registration:
1. Press the Reg soft key on the handset to register quickly.
Normal Registration:
1. Press the OK soft key on the handset, and then select Register Handset.
2. Select the desired base station and then press the OK soft key. The handset begins
searching the base station.
3. Press the OK soft key after searching a base station successfully.
4. Enter the base station PIN (default: 0000), and then press the Done soft key to
complete registration.
If the handset LCD screen does not prompt “Unregistered!”, press the OK key to enter
the main menu, and select Settings->Registration->Register Handset to register
the handset.
Note:
If the handset is registered to the base station successfully, the handset LCD screen
prompts “Handset Subscribed”.
Contact your system administrator for registering more handsets to the base station.
The W80B must work with the W56H/W53H handset running a specific firmware
version. When you register an older handset to the base station, the handset
firmware will be automatically upgraded to a matched one.
Accessing the Web User Interface
1. Press the OK key to enter the main menu, and then select Status->DM.
The handset LCD screen displays the IP address of the W80B.
2. Open a web browser on your computer, enter the IP address into the address bar
(for example, "http://192.168.0.10" or "192.168.0.10"), and then press the Enter.
3. Enter the user name (default: admin) and password (default: admin) in the login page
and click Login.
3
Regulatory Notices
Operating Ambient Temperatures
• Operating temperature: +32 to 104°F (0 to 40°C)
• Relative humidity: 5% to 90%, noncondensing
• Storage temperature: -22 to +160°F (-30 to +70°C)
Warranty
Our product warranty is limited only to the unit itself, when used normally in accordance with the operating instructions and the system environment. We are not
liable for damage or loss resulting from the use of this product, or for any claim
from a third party. We are not liable for problems with Yealink device arising from
the use of this product; we are not liable for financial damages, lost profits, claims
from third parties, etc., arising from the use of this product.
Explanation of the symbols
• DC symbol
is the DC voltage symbol.
• WEEE Warning symbol
Do not disconnect the grounding cable until you disconnect all other cables.
Battery Requirements
• Do not immerse the battery into water, which could short-circuit and damage the battery.
• Do not expose the battery to an open flame or leave the battery where it
could be subjected to extremely high temperatures, which could cause the
battery to explode.
• Do power the handset off before removing the battery.
• Do not try to use the battery for the power supply of any device other than
this handset.
• Do not open or mutilate the battery, released electrolyte is corrosive and
may cause damage to your eyes or skin.
• Use only the rechargeable battery pack delivered with the handset or those
rechargeable battery packs expressly recommended by Yealink.
Defective or exhausted battery should never be disposed of as municipal
waste. Return old battery to the battery supplier, a licensed battery dealer or
a designated collection facility.
Cleaning Requirements
• Before cleaning the device, disconnect it from the power supply.
To avoid the potential effects on the environment and human health as a
• Use a piece of soft, dry and anti-static cloth to clean the device.
result of the presence of hazardous substances in electrical and electronic
• Keep the power plug clean and dry.
equipment, end users of electrical and electronic equipment should under
Troubleshooting
stand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
The unit cannot supply power to Yealink device.
WEEE as unsorted municipal waste and have to collect such WEEE separately.
There is a bad connection with the plug.
Restriction of Hazardous Substances Directive (RoHS)
1. Clean the plug with a dry cloth.
This device complies with the requirements of the EU RoHS Directive. Statements 2. Connect it to another wall outlet.
of compliance can be obtained by contacting support@yealink.com.
The usage environment is out of operating temperature range.
1. Use in the operating temperature range.
Safety Instructions
Save these instructions. Read these safety instructions before use! The cable between the unit and the Yealink device is connected incorrectly.
1. Connect the cable correctly.
You cannot connect the cable properly.
General Requirements
• Before you install and use the device, read the safety instructions carefully 1. You may have connected a wrong Yealink device.
2. Use the correct power supply.
and observe the situation during operation.
• During the process of storage, transportation, and operation, please always Some dust, etc., may be in the port.
1. Clean the port.
keep the device dry and clean, avoid collision and crash.
• Please attempt not to dismantle the device by yourself. In case of any dis- Contact your dealer or authorized service facility for any further questions.
FCC Statement
crepancy, please contact the appointed maintenance center for repair.
• Please refer to the relevant laws and statutes while using the device. Legal This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
rights of others should be respected as well.
(2) this device must accept any interference received, including interference that
Environmental Requirements
may cause undesired operation.
• Place the device at a well-ventilated place. Do not expose the device under
Any Changes or modifications not expressly approved by the party responsible
direct sunlight.
for compliance could void the user’s authority to operate the equipment.
• Keep the device dry and free of dusts.
• Do not place the device on or near any inflammable or fire-vulnerable ob- IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
ject, such as rubber-made materials.
• Keep the device away from any heat source or bare fire, such as a candle or subject to the following two conditions:
(1) this device may not cause interference; and
an electric heater.
(2) this device must accept any interference, including interference that may cause
Operating Requirements
undesired operation of the device. CAN ICES-3(B)
• Do not let a child operate the device without guidance.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux ap• Do not let a child play with the device or any accessory in case of acciden- pareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
tal swallowing.
suivantes :
• Please use the accessories provided or authorized by the manufacturer (1) l’appareil ne doit pas produire de brouillage;
only.
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
• The power supply of the device shall meet the requirements of the input même si le brouillage est susceptible d’en compromettre le fonctionnement.
voltage of the device. Please use the provided surge protection power socket NMB-3(B)
only.
Radiation Exposure Statement
• Before plugging or unplugging any cable, make sure that your hands are
This equipment complies with FCC and IC radiation exposure limits set forth for
completely dry.
• Do not spill liquid of any kind on the product or use the equipment near an uncontrolled environment. This equipment should be installed and operated
water, for example, near a bathtub, washbowl, kitchen sink, wet basement or with minimum distance 20cm between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps
near a swimming pool.
• During a thunderstorm, stop using the device and disconnect it from the qu’aucune autre antenne ou émetteur. Cet équipement devrait être installé et
power supply. Unplug the power plug and the Asymmetric Digital Subscriber actionné avec une distance minimum de 20 centimètres entre le radiateur et votre
Line (ADSL) twisted pair (the radio frequency cable) to avoid lightning strike. corps.
• If the device is left unused for a rather long time, disconnect it from the
power supply and unplug the power plug.
• When there is smoke emitted from the device, or some abnormal noise or
smell, disconnect the device from the power supply, and unplug the power
plug immediately.
• Contact the specified maintenance center for repair.
• Do not insert any object into equipment slots that is not part of the product or auxiliary product.
• Before connecting a cable, connect the grounding cable of the device first.
4
Contact Information
YEALINK NETWORK TECHNOLOGY CO.,LTD.
309, 3rd Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R.C
YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.
Strawinskylaan 3127, Atrium Building, 8th floor, 1077ZX Amsterdam, The Netherlands
YEALINK (USA) NETWORK TECHNOLOGY CO., LTD.
999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA
Made in China
About Yealink
Yealink is a global leading provider of enterprise communication and collaboration solutions,
offering video conferencing service to worldwide enterprises. Focusing on research and
development, Yealink also insists on innovation and creation. With the outstanding technical
patents of cloud computing , audio, video and image processing technology, Yealink has built
up a panoramic collaboration solution of audio and video conferencing by merging its cloud
services with a series of endpoints products. As one of the best providers in more than 140
countries and regions including the US, the UK and Australia, Yealink ranks No.1 in the global
market share of SIP phones shipments.
Technical Support
Visit Yealink WIKI (http://support.yealink.com/) for the latest firmware, guides, FAQ, Product
documents, and more. For better service, we sincerely recommend you to use Yealink Ticketing
system (https://ticket.yealink.com) to submit all your technical issues.
YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD.
Web: www.yealink.com
Copyright©2019 YEALINK(XIAMEN) NETWORK
TECHNOLOGY CO.,LTD.All rights reserved.
W8 0 B - E N
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement