Cyp PU-DVI1109RX DVI 5-Play HDBaseT™ Receiver (inc. PoC & 2x LAN, up to 100m) Manual

Cyp PU-DVI1109RX DVI 5-Play HDBaseT™ Receiver (inc. PoC & 2x LAN, up to 100m) Manual
PU-DVI1109TX & RX
DVI 5-Play HDBaseT™ Transmitter and Receiver
inc. PoC & 2x LAN, up to 100m
OPERATION MANUAL
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer file, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
3
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•
Never spill liquid of any kind on or into this product.
•
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
•
Do not attach the power supply cabling to building surfaces.
•
Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
•
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
•
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE
SUMMARY OF CHANGE
v1.00
First release
4
06/06/2017
CONTENTS
1. Introduction�������������������������������������������6
2. Applications�������������������������������������������6
3. Package Contents����������������������������������6
4. System Requirements���������������������������7
5. Features��������������������������������������������������7
6. Operation Controls and Functions�������8
6.1 Transmitter Front and Rear Panels������� 8
6.2 Receiver Front and Rear Panels������������ 9
6.3 IR Cable Pin Assignment�����������������������10
6.4 D-Sub 9-Pin Definitions�������������������������10
7. Connection Diagram �������������������������� 11
8. Specifications�������������������������������������� 12
9. Acronyms��������������������������������������������� 13
5
1. INTRODUCTION
This HDBaseT DVI over CAT5e/6/7 Transmitter and Receiver set can
transmit DVI video, analog audio, 2 LAN serving connections, control (RS232 and IR) and Power over Cable (PoC) over a single CAT5e/6/7 cable up
to 100m. The Transmitter can power the Receiver, via the PoC function,
eliminating the need for a separate power supply providing greater
flexibility in installations.
2. APPLICATIONS
Household entertainment media sharing and control
Lecture room display and control
Showroom display and control
Meeting room presentation and control
Classroom display and control
Any Smart AV Installation system
3. PACKAGE CONTENTS
Transmitter Package
DVI to CAT5e/6/7 with LAN/PoC/IR Transmitter
1×IR Blaster
1×IR Receiver
24 V DC Power Adaptor
Operation Manual
Receiver Package
CAT5e/6/7 to DVI with LAN/PoC/IR Receiver
1×IR Blaster
1×IR Receiver
Operation Manual
Note: Units are sold separately
6
4. SYSTEM REQUIREMENTS
Input DVI source equipment such as PC/Laptop and output display
with DVI input.
RS232 controlled device
Ethernet equipped device
5. FEATURES
Simultaneous transmission of uncompressed video and audio
(1080p@60Hz/-Deep Color) over a single CAT5e/6/7 cable for up to
100 m (300 ft.).
Supports High-definition Audio up to LPCM 7.1CH, Dolby TrueHD and
DTS-HD Master Audio with HDMI to DVI adaptor
Connect and share up to 4 LAN connections (2 at the Transmitter end,
2 at the Receiver end) at speeds up to 100 Mbps
Supports Bi-directional IR control and RS-232 pass-through
Supports 5Play™ convergence: HD video, audio & Control ports (IR and
RS232)/LAN/PoC
Installation friendly
Single power supply powers both units, Receiver unit is powered
through the Transmitter via PoC
Note:
1. This system was tested with CAT6/23AWG cables, results may vary with
cables of a different specification.
2. The PoC function is designed for powering compatible Receiver units
only—non-PoC Receivers will need their own power supply.Receivers of
another brand may not be compatible.
3. Supporting 4K2K resolution with DVI to HDMI adaptor cable.
7
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
Rear
Front
DC 24V
POWER
1
2
AUDIO IN
LINK
IR 1
OUT
IR 2
IN
RS232 IN
3
4
5
6
CAT5e/6/7 OUT
DVI IN
7
8
L
R
9
LAN 1
LAN 2
10
1 Power LED: This LED will illuminate when the 24 V DC Adaptor is
connected to the AC outlet.
2 DC 24V: Plug the 24 V DC power supply into the unit and connect the
adaptor to an AC outlet.
3 IR 1 OUT: Connect to the supplied IR Blaster cables for IR signal
transmission. Place the IR Blaster in direct line-ofsight of the
equipment to be controlled. The related IR Receiver port is IR1 IN.
4 IR 2 IN : Connect to the supplied IR Receiver cables for IR signal
reception. Ensure that remote being used is within the direct line-ofsight of the IR Extender. The related IR Transmitter port is IR2 OUT.
5 RS-232 IN: Connect to a PC/Laptop with a D-Sub 9-pin male cable for
the transmission of RS-232 commands.
6 Link LED: The yellow LED will illuminate when both the input source
and output display signals are connected through the CAT cable.
When it blinks regularly it states the source is NOT sending a signal to
the Transmitter but the Transmitter and Receiver are linked and if it
blink irregularly it states an error has occurred.
7 CAT5e/6/7 OUT: Connect the Transmitter and Receiver via a single
CAT5e/6 type cable for all data transmission.
8 DVI IN: Connect to the DVI equipped source equipment such as PC or
Laptop.
9 AUDIO IN L/R: Connect from audio source equipment for audio signal
output to L/R output on the Receiver side.
10 LAN 1/2: The LAN connections can be used to connect and share up
to 4 Ethernet connections (2 at the Receiver end, 2 at the Transmitter
end), including computers, routers and media servers.
8
6.2 Receiver Front and Rear Panels
Rear
Front
POWER
1
AUDIO OUT
LINK
IR 1
IN
IR 2
OUT
RS232 OUT
2
3
4
5
CAT5e/6/7 IN
DVI OUT
6
7
L
R
8
LAN 1
LAN 2
9
1 Power LED: The LED will illuminate when the 24 V DC Adaptor is
connected to the AC outlet.
2 IR 1 IN: Connect to supplied the IR Receiver cables for IR signal
reception. Place the IR Blaster in direct line-of-sight of the equipment
to be controlled. The related IR Transmitter port is IR1 OUT.
3 IR 2 OUT: Connect to the supplied IR Blaster cables for IR signal
transmission. Ensure that remote being used is within the direct lineof-sight of the IR Extender. The related IR Receiver port is IR2 IN.
4 RS-232 OUT: Connect to a RS-232 enabled device with a D-Sub 9-pin
female cable for the transmission of RS-232 commands.
5 Link LED: The yellow LED will illuminate when both the input source
and output display signals are connected through the CAT cable.
When it blinks regularly it states the source is NOT sending a signal to
the Transmitter but the Transmitter and Receiver are linked and if it
blink irregularly it states an error has occurred.
6 CAT5e/6/7 IN: Connect the Transmitter and Receiver via a single
CAT5e/6 type cable for all data transmission.
7 DVI OUT: Connect to a DVI equipped display or monitor to display the
DVI input source signal.
8 AUDIO OUT L/R: Connect to active speakers or amplifier for audio
signal output.
9 LAN 1/2: The LAN connections can be used to connect and share up
to 4 Ethernet connections (2 at the Receiver end, 2 at the Transmitter
end), including computers, routers and media servers.
9
6.3 IR Cable Pin Assignment
IR Blaster
1 Power
2 IR Blaster Signal
3 NC
IR Receiver
1 IR Signal
2 Power
3 Ground
6.4 D-Sub 9-Pin Definitions
Pin
Define TX/RX
1
N/C
2
TxD / RxD
3
RxD / TxD
4
N/C
5
GND
6
N/C
7
N/C
8
N/C
9
N/C
10
7. CONNECTION DIAGRAM
Notebook
PC with RS232
Control
IR Extender
IR Blaster
Modem/Router
7m
m
3m
3m
60°
Media Server
AUDIO IN
DVI IN
Power
Supply
L
R
LAN 1
DC 24V
POWER
LAN 2
TX
LINK
IR 1
OUT
IR 2
IN
RS232 IN
CAT5e/6/7 OUT
Single CAT5e/6/7
PC
RS232 Controlled
Device
RX
POWER
LINK
3m
IR 1
IN
IR 2
OUT
RS232 OUT
CAT5e/6/7 IN
7m
m
AUDIO OUT
3m
60°
IR Extender
DVI OUT
L
R
LAN 1
LAN 2
60°
1.5m
IR Blaster
Monitor/Display
1.5m
60°
IR BLASTER
60°
3m
7m
Notebook
3m
IR RECEIVER
Active Speakers
11
8. SPECIFICATIONS
Video Bandwidth
340 MHz/10.2 Gbps
Ethernet Speed
100 Mbps
Transmitter
Inputs
1×DVI , 2×Ethernet, 1 x L/R
Outputs
1×RS-232, 1×IR Extender
1×CAT5e/6/7, 1×IR Blaster
Receiver
Inputs
1×CAT5e/6/7, 1×IR Extender
Outputs
1×DVI, 1×RS-232, 1 x L/R
DVI In/Out Cable Distance
2 ×Ethernet, 1×IR Blaster
Up to 6 Meters
CAT6 In/Out Cable
Up to 100 Meters
Distance
DVI In/Out Supports
Resolution
IR Frequency
ESD Protection
480i~1080p@50/60, 1080p@24,
VGA~WUXGA(Dual Link DVI Not Supported)
30~50 kHz
Human body model:
±8kV (air-gap discharge)
Power Supply
±4kV (contact discharge)
24 V/1.25 A DC (US/EU Standards, CE/FCC/UL certi-
Dimensions
fied)
125 mm(W) x 123 mm (D) x 30 mm (H)/Jacks
Excluded
125 mm(W) x 135 mm (D) x 30 mm (H)/Jacks
Weight
Included
384 g (TXC)
Chassis Material
392 g (RXC)
Aluminum
Silkscreen Color
Black
Operating Temperature
0˚C~40˚C/32˚F~104˚F
Storage Temperature
−20 ˚C~60 ˚C/−4˚F~140 ˚F
Relative Humidity
20~90 % RH (non-condensing)
Power Consumption
13 W
12
9. ACRONYMS
ACRONYM
COMPLETE TERM
CAT5e
Category 5 Cable
CAT6
Category 6 Cable
CAT7
Category 7 Cable
HDMI
High Definition Multimedia Interface
PoC
Power over Cable
13
CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton,
Middlesex, TW17 8BA
Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279
Email: sales@cypeurope.com
www.cypeurope.com
v1.00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement