Cyp PRO-SDIHDMI SDI to HDMI Converter with SDI Bypass Manual

Cyp PRO-SDIHDMI SDI to HDMI Converter with SDI Bypass Manual
PRO-SDIHDMI
SDI to HDMI Converter with SDI Bypass
OPERATION MANUAL
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer file, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2019 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
3
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•
Never spill liquid of any kind on or into this product.
•
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
•
Do not attach the power supply cabling to building surfaces.
•
Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
•
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
•
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE
SUMMARY OF CHANGE
v2.00
Updated format/Diagrams
4
26/06/2019
CONTENTS
1. Introduction�������������������������������������������6
2. Applications�������������������������������������������6
3. Package Contents����������������������������������6
4. System Requirements���������������������������6
5. Features��������������������������������������������������7
6. Operation Controls and Functions�������8
6.1 Front Panels������������������������������������������������� 8
6.2 Rear Panel����������������������������������������������������� 9
7. Connection Diagram�������������������������� 10
8. Specifications�������������������������������������� 11
9. Acronyms��������������������������������������������� 12
5
1. INTRODUCTION
The SDI to HDMI Converter allows SD, HD and 3G-SDI signals to be shown
on HDMI display. This means that it is now easier for professionals to
distribute and extend their SDI signal while giving the ability to display
work on HDMI displays. Furthermore, thanks to L/R audio outputs users
can output audio in analogue formats while the loop-through 3G-SDI
design benefits users by letting them simultaneous show content on both
SDI and HDMI displays.
2. APPLICATIONS
SDI signal loop-out and extension
Converts SDI signal (SD/HD/3G) to HDMI
3. PACKAGE CONTENTS
3G SDI to HDMI Extender
5V/2.6A DC power adaptor
Operation Manual
4. SYSTEM REQUIREMENTS
Source SDI input with an SDI cable and output to SDI and/or HDMI
displays with suitable connection cables.
6
5. FEATURES
Supports SD-SDI, HD-SDI and 3G-SDI input signals with autodetection
Supports HDMI and SDI (bypass) output simultaneously
SDI interface operates at bitrates of 2.970 Gbit/s, 2.970/1.001 Gbit/s,
1.485 Gbit/s, 1.485/1.001 Gbit/s and 270 Mb/s
Converts SDI signal to HDMI:
1. SD-SDI (SMPTE 259M-C) to 480i/576i
2. HD-SDI (SMPTE 292M) to 720p@50/59.94/60, 1080i@50/59.94/60
3. 3G-SDI (SMPTE 424M/425M-AB) to 1080p@23.98/24/25/29.97/30/5
0/59.94/60, 1080PsF@23.98/24/25/29.97/30
Supports SDI input modes:
1. SD-SDI (SMPTE 259M-C, at bitrates of 270 Mbit/s)
2. HD-SDI (SMPTE 292M, at bitrates of 1.485 Gbit/s and
1.485/1.001 Gbit/s)
3. 3G-SDI (SMPTE 424M/425M-AB, at bitrates of 2.970 Gbit/s and
2.970/1.001 Gbit/s)
Equalised and re-clocked loop output
Alternative audio output to coaxial and analogue 2 CH
Supports SDI input/output distance up to 100 metres (3G-SDI), 200
metres (HD-SDI), or 300 metres (SD-SDI)
Note: Tested with Belden 1694A cable. Operating distances may vary with
other specifications of cable.
7
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panels
1
2
3
4
Video Audio HDMI/
Power Lock Lock DVI
3G
HD
SD
5
6
7
Audio Out
R
HDMI Out
L
8
9
1 Power LED: The LED will illuminate red when the device is connected
to a power supply.
2 Video Lock LED: The LED will illuminate green when both the input
SDI source and the output HDMI display have successfully sent and
received a signal.
3 Audio Lock LED: The LED will illuminate green when the input SDI
source has an audio signal and when the output HDMI/DVI display is
active.
4 HDMI/DVI LED: The LED will illuminate green only when connected
to an HDMI display. It will remain off when connected to a DVI display.
The device will read the output display’s EDID information and
automatically determine whether to send a HDMI or DVI signal.
5 3G LED: This LED illuminate yellow when a 3G-SDI input signal is
detected.
6 HD LED: This LED illuminate yellow when a HD-SDI input signal is
detected.
7 SD LED: This LED illuminate yellow when a SD-SDI input signal is
detected.
8 Audio out R/L: Analogue audio output (L/R Stereo). Connect to an
amplifier or recording device with a suitable analogue input.
9 HDMI Out: Connect to a HDMI equipped display or to a DVI Display
with a HDMI to DVI adaptor cable.
8
6.2 Rear Panel
SDI IN
SDI OUT
DC 5V
1
2
3
1 SDI IN: Connect to the SDI output of the SDI source device. Accepts
SD, HD or 3G SDI signals.
2 SDI OUT: Provides a 'loop-through' SDI signal output for connection
to a SDI display or device. Can be connected to another SDI to HDMI
converter/extender to extend the signal or to connect to multiple
displays for mirrored output.
3 DC 5V: Plug the 5 V DC power supply into the unit and connect the
adaptor to an AC outlet.
9
7. CONNECTION DIAGRAM
SDI Camera
Cascade to
another Unit
SDI IN
SDI OUT
SDI Display
DC 5V
OR
SDI Input
SDI Output
SDI IN
SDI OUT
Video Audio HDMI/
Power Lock Lock DVI
3G
HD
SD
Audio Out
R
DC 5V
HDMI Out
L
3GSDI to HDMI CLUX-SDI2HC
HDMI
Output
Stereo
Audio
Output
Amplifier
10
HDMI Display
8. SPECIFICATIONS
SMPTE Standard
425M Level A & B, 424M, 292M, 259M-C
SDI Transmission Rates
2.970 Gbps, 2.970/1.001 Gbps
1.485 Gbps, 1.485/1.001 Gbps and 270 Mbps
Video Bandwidth
225 MHz/6.75Gbps
Input
1×BNC (SD/HD/3G-SDI)
Output
1×BNC (SD/HD/3G-SDI), 1×HDMI, 2×RCA
SDI Timing Support
SD-SDI:
SMPTE 259M-C, 270 Mbit/s
HD-SDI:
SMPTE 292M, 1.485 & 1.485/1.001 Gbit/s
3G-SDI:
SMPTE 424M/425M-AB, 2.970 &
2.970/1.001 Gbit/s
HDMI Timing Support
480i, 576i, 720p@50/59.94/60
1080i@50/59.94/60
1080p@23.98/24/25/29.97/30/50/59.94/60
SDI Cable Distance
3G/HD/3G-SDI up to 100 /200/300 metres with
BELDEN 1694A Cable
Power Supply
5 V DC/2.6 A (US/EU standards, CE/FCC/
UL certified)
ESD Protection
Human-body Model:
±8 kV (air-gap discharge)
±4kV (contact discharge)
Dimensions
137 mm (W)×90 mm (D)×25 mm (H)
Weight
225 g
Chassis Material
Aluminum
Silkscreen Colour
Black
Operating Temperature
0 °C~40 °C/32 °F~104 °F
Storage Temperature
−20 °C~60 °C/−4 °F~104 °F
Relative Humidity
20~90 % RH (Non-condensing)
Power Consumption
4W
11
9. ACRONYMS
ACRONYM
COMPLETE TERM
3G
Bandwidth 2.97Gbps ≈ 3G
DVI
Digital Visual Interface
HDCP
High-bandwidth Digital content protection
HDMI
High Definition Multimedia Interface
SDI
Serial Digital Interface
12
CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton,
Middlesex, TW17 8BA
Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279
Email: sales@cypeurope.com
www.cypeurope.com
v2.00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement