Miller AUTO-AXCESS 675 DI Owner’s Manual

OM-240 146H
2011−09
Processes
MIG (GMAW) Welding
Pulsed MIG (GMAW-P)
Flux Cored (FCAW) Welding
Automatic Welding
Description
Automatic Welding Interface And
Arc Welding Power Source
Auto-Axcess 675 DI
™
Visit our website at
www.MillerWelds.com/ams
File: Advanced Manufacturing Systems
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001:2000 Quality Warranty and service information for your
System Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual specification sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 2009−09
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Symboles utilisés . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance . . . . .
2-4. Proposition californienne 65 Avertissements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6. Informations relatives aux CEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Dimensions And Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4. Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5. Serial Number And Rating Label Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-6. Selecting A Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-7. Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8. Optional Tandem Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-9. Rear Panel Receptacles And Supplementary Protectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-10. Connecting To Weld Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-11. Selecting Weld Cable Sizes* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-12. Devicenet Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-13. Motor Control Receptacle Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-14. E-Stop Receptacle Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-15. Tandem Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-16. Electrical Service Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-17. Connecting Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-18. Remote Program Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-19. Remote Program Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-20. Touch Sensor Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Operational Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Front Panel Controls (See Section 4-3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Front Panel Controls - Continued (See Section 4-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Front Panel Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Reset Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Blowing Out Inside Of Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
3
4
4
4
5
5
5
7
8
9
9
11
11
11
12
12
13
13
13
14
15
16
17
18
18
18
19
19
20
21
21
21
22
22
24
25
26
27
28
28
28
TABLE OF CONTENTS
SECTION 6 − SAFETY PRECAUTIONS FOR SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Servicing Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Set Value Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3. Removing Cover and Measuring Input Capacitor Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4. Process Control Module PC4 Diagnostic LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5. Diagnostic LEDs On Process Control Module PC4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-6. Wire Feed Module PC6 Diagnostic LEDs And Dip Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-7. Diagnostic LEDs On Wire Feed Module PC6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-8. User Interface Module PC7 Diagnostic LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-9. Diagnostic LEDs On User Interface Module PC7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-10. Network And Module Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-11. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − ELECTRICAL DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY
29
29
29
30
30
31
31
32
35
36
36
37
37
38
38
39
40
42
48
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som 2011−01
7
Protect yourself and others from injury — read and follow these precautions.
1-1. Symbol Usage
DANGER! − Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in the text.
NOTICE − Indicates statements not related to personal injury.
. Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the
hazards.
1-2. Arc Welding Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information
found in the Safety Standards listed in Section 1-5. Read and
follow all Safety Standards.
Only qualified persons should install, operate, maintain, and
repair this unit.
During operation, keep everybody, especially children, away.
D Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
D When making input connections, attach proper grounding conductor first − double-check connections.
D Keep cords dry, free of oil and grease, and protected from hot metal
and sparks.
D Frequently inspect input power cord for damage or bare wiring −
replace cord immediately if damaged − bare wiring can kill.
D Turn off all equipment when not in use.
D Do not use worn, damaged, undersized, or poorly spliced cables.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic
wire welding, the wire, wire reel, drive roll housing,
and all metal parts touching the welding wire are
electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
D Do not touch live electrical parts.
D Wear dry, hole-free insulating gloves and body protection.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
D Use AC output ONLY if required for the welding process.
D If AC output is required, use remote output control if present on
unit.
D Additional safety precautions are required when any of the following electrically hazardous conditions are present: in damp
locations or while wearing wet clothing; on metal structures such
as floors, gratings, or scaffolds; when in cramped positions such
as sitting, kneeling, or lying; or when there is a high risk of unavoidable or accidental contact with the workpiece or ground. For these
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone!
D Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
D Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
D Do not drape cables over your body.
D If earth grounding of the workpiece is required, ground it directly
with a separate cable.
D Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
D Do not touch electrode holders connected to two welding machines at the same time since double open-circuit voltage will be
present.
D Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
D Wear a safety harness if working above floor level.
D Keep all panels and covers securely in place.
D Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
D Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
D Do not connect more than one electrode or work cable to any
single weld output terminal.
SIGNIFICANT DC VOLTAGE exists in inverter welding power sources AFTER removal of input power.
D Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
HOT PARTS can burn.
D Do not touch hot parts bare handed.
D Allow cooling period before working on equipment.
D To handle hot parts, use proper tools and/or
wear heavy, insulated welding gloves and
clothing to prevent burns.
OM-240 146 Page 1
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D Keep your head out of the fumes. Do not breathe the fumes.
D If inside, ventilate the area and/or use local forced ventilation at the
arc to remove welding fumes and gases.
D If ventilation is poor, wear an approved air-supplied respirator.
D Read and understand the Material Safety Data Sheets (MSDSs)
and the manufacturer’s instructions for metals, consumables,
coatings, cleaners, and degreasers.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
D Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements
can give off toxic fumes if welded.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear an approved welding helmet fitted with a proper shade of
filter lenses to protect your face and eyes from arc rays and
sparks when welding or watching (see ANSI Z49.1 and Z87.1
listed in Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash,
glare and sparks; warn others not to watch the arc.
D Wear protective clothing made from durable, flame-resistant
material (leather, heavy cotton, or wool) and foot protection.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D Do not weld where flying sparks can strike flammable material.
D Protect yourself and others from flying sparks and hot metal.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
D Do not weld where the atmosphere may contain flammable dust,
gas, or liquid vapors (such as gasoline).
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock, sparks, and fire
hazards.
D Do not use welder to thaw frozen pipes.
OM-240 146 Page 2
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
D Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
D After completion of work, inspect area to ensure it is free of sparks,
glowing embers, and flames.
D Use only correct fuses or circuit breakers. Do not oversize or bypass them.
D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
for hot work and have a fire watcher and extinguisher nearby.
FLYING METAL or DIRT can injure eyes.
D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
D Wear approved safety glasses with side
shields even under your welding helmet.
BUILDUP OF GAS can injure or kill.
D Shut off compressed gas supply when not in use.
D Always ventilate confined spaces or use
approved air-supplied respirator.
ELECTRIC AND MAGNETIC FIELDS (EMF)
can affect Implanted Medical Devices.
D Wearers of Pacemakers and other Implanted
Medical Devices should keep away.
D Implanted Medical Device wearers should consult their doctor
and the device manufacturer before going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating
operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Wear approved ear protection if noise level is
high.
CYLINDERS can explode if damaged.
Compressed gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D Protect compressed gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open flames, sparks, and arcs.
D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Keep cylinders away from any welding or other electrical circuits.
D Never drape a welding torch over a gas cylinder.
D Never allow a welding electrode to touch any cylinder.
D Never weld on a pressurized cylinder − explosion will result.
D Use only correct compressed gas cylinders, regulators, hoses,
and fittings designed for the specific application; maintain them
and associated parts in good condition.
D Turn face away from valve outlet when opening cylinder valve.
D Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D Use the right equipment, correct procedures, and sufficient number of persons to lift and move cylinders.
D Read and follow instructions on compressed gas cylinders,
associated equipment, and Compressed Gas Association (CGA)
publication P-1 listed in Safety Standards.
1-3. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
D Do not install or place unit on, over, or near
combustible surfaces.
D Do not install unit near flammables.
D Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
FALLING EQUIPMENT can injure.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are long enough to
extend beyond opposite side of unit.
D Keep equipment (cables and cords) away from moving vehicles
when working from an aerial location.
D Follow the guidelines in the Applications Manual for the Revised
NIOSH Lifting Equation (Publication No. 94−110) when manually lifting heavy parts or equipment.
MOVING PARTS can injure.
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
D Have only qualified persons remove doors, panels, covers, or
guards for maintenance and troubleshooting as necessary.
D Reinstall doors, panels, covers, or guards when maintenance is
finished and before reconnecting input power.
READ INSTRUCTIONS.
D Read and follow all labels and the Owner’s
Manual carefully before installing, operating, or
servicing unit. Read the safety information at
the beginning of the manual and in each
section.
D Use only genuine replacement parts from the manufacturer.
D Perform maintenance and service according to the Owner’s
Manuals, industry standards, and national, state, and local
codes.
OVERUSE can cause OVERHEATING
H.F. RADIATION can cause interference.
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
FLYING SPARKS can injure.
D Wear a face shield to protect eyes and face.
D Shape tungsten electrode only on grinder with
proper guards in a safe location wearing proper
face, hand, and body protection.
D Sparks can cause fires — keep flammables away.
D
D
D
D
STATIC (ESD) can damage PC boards.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
ARC WELDING can cause interference.
MOVING PARTS can injure.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
WELDING WIRE can injure.
D Do not press gun trigger until instructed to do
so.
D Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
D
D
D
D
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
OM-240 146 Page 3
1-4. California Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
For Gasoline Engines:
Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
For Diesel Engines:
Diesel engine exhaust and some of its constituents are
known to the State of California to cause cancer, birth
defects, and other reproductive harm.
This product contains chemicals, including lead, known to
the state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after use.
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 4221 Walney Road, 5th Floor,
Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:
800-463-6727, website: www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
U.S. Consumer Product Safety Commission (CPSC), 4330 East West
Highway, Bethesda, MD 20814 (phone: 301-504-7923, website:
www.cpsc.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website:
www.cdc.gov/NIOSH).
1-6. EMF Information
Electric current flowing through any conductor causes localized electric
and magnetic fields (EMF). Welding current creates an EMF field
around the welding circuit and welding equipment. EMF fields may interfere with some medical implants, e.g. pacemakers. Protective
measures for persons wearing medical implants have to be taken. For
example, access restrictions for passers−by or individual risk assessment for welders. All welders should use the following procedures in
order to minimize exposure to EMF fields from the welding circuit:
1. Keep cables close together by twisting or taping them, or using a
cable cover.
2. Do not place your body between welding cables. Arrange cables
to one side and away from the operator.
3. Do not coil or drape cables around your body.
OM-240 146 Page 4
4. Keep head and trunk as far away from the equipment in the
welding circuit as possible.
5. Connect work clamp to workpiece as close to the weld as
possible.
6. Do not work next to, sit or lean on the welding power source.
7. Do not weld whilst carrying the welding power source or wire
feeder.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION
fre_som_2011−01
7
Se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
2-1. Symboles utilisés
DANGER! − Indique une situation dangereuse qui si on
l’évite pas peut donner la mort ou des blessures graves.
Les dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
Indique une situation dangereuse qui si on l’évite pas
peut donner la mort ou des blessures graves. Les dangers possibles sont montrés par les symboles joints ou
sont expliqués dans le texte.
NOTE − Indique des déclarations pas en relation avec des blessures
personnelles.
. Indique des instructions spécifiques.
Ce groupe de symboles veut dire Avertissement! Attention! DANGER
DE CHOC ELECTRIQUE, PIECES EN MOUVEMENT, et PIECES
CHAUDES. Consulter les symboles et les instructions ci-dessous y
afférant pour les actions nécessaires afin d’éviter le danger.
2-2. Dangers relatifs au soudage à l’arc
Les symboles représentés ci-dessous sont utilisés dans ce manuel pour attirer l’attention et identifier les dangers possibles. En
présence de l’un de ces symboles, prendre garde et suivre les
instructions afférentes pour éviter tout risque. Les instructions
en matière de sécurité indiquées ci-dessous ne constituent
qu’un sommaire des instructions de sécurité plus complètes
fournies dans les normes de sécurité énumérées dans la Section 2-5. Lire et observer toutes les normes de sécurité.
D
Seul un personnel qualifié est autorisé à installer, faire fonctionner, entretenir et réparer cet appareil.
D
Pendant le fonctionnement, maintenir à distance toutes les
personnes, notamment les enfants de l’appareil.
D
UNE DÉCHARGE ÉLECTRIQUE peut
entraîner la mort.
Le contact d’organes électriques sous tension peut
provoquer des accidents mortels ou des brûlures
graves. Le circuit de l’électrode et de la pièce est
sous tension lorsque le courant est délivré à la
sortie. Le circuit d’alimentation et les circuits internes de la machine sont également sous tension
lorsque l’alimentation est sur Marche. Dans le mode
de soudage avec du fil, le fil, le dérouleur, le bloc de
commande du rouleau et toutes les parties métalliques en contact avec le fil sont sous tension
électrique. Un équipement installé ou mis à la terre
de manière incorrecte ou impropre constitue un
danger.
D Ne pas toucher aux pièces électriques sous tension.
D Porter des gants isolants et des vêtements de protection secs et
sans trous.
D S’isoler de la pièce à couper et du sol en utilisant des housses ou
des tapis assez grands afin d’éviter tout contact physique avec la
pièce à couper ou le sol.
D Ne pas se servir de source électrique à courant électrique dans les
zones humides, dans les endroits confinés ou là où on risque de
tomber.
D Se servir d’une source électrique à courant électrique UNIQUEMENT si le procédé de soudage le demande.
D Si l’utilisation d’une source électrique à courant électrique s’avère
nécessaire, se servir de la fonction de télécommande si l’appareil
en est équipé.
D D’autres consignes de sécurité sont nécessaires dans les conditions suivantes : risques électriques dans un environnement
humide ou si l’on porte des vêtements mouillés ; sur des structures
métalliques telles que sols, grilles ou échafaudages ; en position
coincée comme assise, à genoux ou couchée ; ou s’il y a un risque
élevé de contact inévitable ou accidentel avec la pièce à souder ou
le sol. Dans ces conditions, utiliser les équipements suivants,
D
D
D
D
dans l’ordre indiqué : 1) un poste à souder DC à tension constante
(à fil), 2) un poste à souder DC manuel (électrode) ou 3) un poste à
souder AC à tension à vide réduite. Dans la plupart des situations,
l’utilisation d’un poste à souder DC à fil à tension constante est recommandée. En outre, ne pas travailler seul !
Couper l’alimentation ou arrêter le moteur avant de procéder à l’installation, à la réparation ou à l’entretien de l’appareil. Déverrouiller
l’alimentation selon la norme OSHA 29 CFR 1910.147 (voir normes de sécurité).
Installer le poste correctement et le mettre à la terre convenablement selon les consignes du manuel de l’opérateur et les normes
nationales, provinciales et locales.
Toujours vérifier la terre du cordon d’alimentation. Vérifier et
s’assurer que le fil de terre du cordon d’alimentation est bien
raccordé à la borne de terre du sectionneur ou que la fiche du
cordon est raccordée à une prise correctement mise à la terre.
En effectuant les raccordements d’entrée, fixer d’abord le conducteur de mise à la terre approprié et contre-vérifier les connexions.
Les câbles doivent être exempts d’humidité, d’huile et de graisse;
protégez−les contre les étincelles et les pièces métalliques
chaudes.
Vérifier fréquemment le cordon d’alimentation afin de s’assurer
qu’il n’est pas altéré ou à nu, le remplacer immédiatement s’il l’est.
Un fil à nu peut entraîner la mort.
L’équipement doit être hors tension lorsqu’il n’est pas utilisé.
D Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante ou mal épissés.
D Ne pas enrouler les câbles autour du corps.
D Si la pièce soudée doit être mise à la terre, le faire directement
avec un câble distinct.
D Ne pas toucher l’électrode quand on est en contact avec la pièce,
la terre ou une électrode provenant d’une autre machine.
D Ne pas toucher des porte électrodes connectés à deux machines
en même temps à cause de la présence d’une tension à vide doublée.
D N’utiliser qu’un matériel en bon état. Réparer ou remplacer sur-lechamp les pièces endommagées. Entretenir l’appareil conformément à ce manuel.
D Porter un harnais de sécurité si l’on doit travailler au-dessus du sol.
D S’assurer que tous les panneaux et couvercles sont correctement
en place.
D Fixer le câble de retour de façon à obtenir un bon contact métalmétal avec la pièce à souder ou la table de travail, le plus près possible de la soudure.
D Isoler la pince de masse quand pas mis à la pièce pour éviter le
contact avec tout objet métallique.
D Ne pas raccorder plus d’une électrode ou plus d’un câble de
masse à une même borne de sortie de soudage.
OM-240 146 Page 5
Il reste une TENSION DC NON NÉGLIGEABLE dans
les sources de soudage onduleur UNE FOIS
l’alimentation coupée.
D Arrêter les convertisseurs, débrancher le courant électrique et
décharger les condensateurs d’alimentation selon les instructions
indiquées dans la partie Entretien avant de toucher les pièces.
LES PIÈCES CHAUDES peuvent
provoquer des brûlures.
D Ne pas toucher à mains nues les parties
chaudes.
D Prévoir une période de refroidissement avant de
travailler à l’équipement.
D Ne pas toucher aux pièces chaudes, utiliser les outils recommandés et porter des gants de soudage et des vêtements épais pour
éviter les brûlures.
LE SOUDAGE peut provoquer un
incendie ou une explosion.
Le soudage effectué sur des conteneurs fermés tels
que des réservoirs, tambours ou des conduites peut
provoquer leur éclatement. Des étincelles peuvent
être projetées de l’arc de soudure. La projection d’étincelles, des
pièces chaudes et des équipements chauds peut provoquer des
incendies et des brûlures. Le contact accidentel de l’électrode avec
des objets métalliques peut provoquer des étincelles, une explosion,
un surchauffement ou un incendie. Avant de commencer le soudage,
vérifier et s’assurer que l’endroit ne présente pas de danger.
D Déplacer toutes les substances inflammables à une distance de
10,7 m de l’arc de soudage. En cas d’impossibilité les recouvrir
soigneusement avec des protections homologués.
D Ne pas souder dans un endroit là où des étincelles peuvent tomber
sur des substances inflammables.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
D Se protéger et d’autres personnes de la projection d’étincelles et
de métal chaud.
Le soudage génère des fumées et des gaz. Leur
inhalation peut être dangereux pour votre santé.
D Des étincelles et des matériaux chauds du soudage peuvent
facilement passer dans d’autres zones en traversant de petites
fissures et des ouvertures.
D Eloigner votre tête des fumées. Ne pas respirer les fumées.
D Surveiller tout déclenchement d’incendie et tenir un extincteur à
proximité.
D À l’intérieur, ventiler la zone et/ou utiliser une ventilation forcée au
niveau de l’arc pour l’évacuation des fumées et des gaz de
soudage.
D Le soudage effectué sur un plafond, plancher, paroi ou séparation
peut déclencher un incendie de l’autre côté.
D Si la ventilation est médiocre, porter un respirateur anti-vapeurs
approuvé.
D Lire et comprendre les spécifications de sécurité des matériaux
(MSDS) et les instructions du fabricant concernant les métaux, les
consommables, les revêtements, les nettoyants et les dégraisseurs.
D Travailler dans un espace fermé seulement s’il est bien ventilé ou
en portant un respirateur à alimentation d’air. Demander toujours à
un surveillant dûment formé de se tenir à proximité. Des fumées et
des gaz de soudage peuvent déplacer l’air et abaisser le niveau
d’oxygène provoquant des blessures ou des accidents mortels.
S’assurer que l’air de respiration ne présente aucun danger.
D Ne pas souder dans des endroits situés à proximité d’opérations
de dégraissage, de nettoyage ou de pulvérisation. La chaleur et
les rayons de l’arc peuvent réagir en présence de vapeurs et former des gaz hautement toxiques et irritants.
D Ne pas souder des métaux munis d’un revêtement, tels que l’acier
galvanisé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait été enlevé dans la zone de soudure, que l’endroit soit
bien ventilé, et en portant un respirateur à alimentation d’air. Les
revêtements et tous les métaux renfermant ces éléments peuvent
dégager des fumées toxiques en cas de soudage.
LES RAYONS DE L’ARC peuvent
provoquer des brûlures dans les
yeux et sur la peau.
Le rayonnement de l’arc du procédé de soudage
génère des rayons visibles et invisibles intense
(ultraviolets et infrarouges) susceptibles de provoquer des brûlure
dans les yeux et sur la peau. Des étincelles sont projetées pendant le
soudage.
D Porter un casque de soudage approuvé muni de verres filtrants
approprié pour protéger visage et yeux pour protéger votre visage
et vos yeux pendant le soudage ou pour regarder (voir ANSI Z49.1
et Z87.1 énuméré dans les normes de sécurité).
D Porter des lunettes de sécurité avec écrans latéraux même sous
votre casque.
D Avoir recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements les éblouissements
et les étincelles ; prévenir toute personne sur les lieux de ne pas
regarder l’arc.
D Porter des vêtements confectionnés avec des matières résistantes et ignifuges (cuir, coton lourd ou laine) et des bottes de
protection.
OM-240 146 Page 6
D Ne pas effectuer le soudage sur des conteneurs fermés tels que
des réservoirs, tambours, ou conduites, à moins qu’ils n’aient été
préparés correctement conformément à AWS F4.1 (voir les normes de sécurité).
D Ne soudez pas si l’air ambiant est chargé de particules, gaz, ou vapeurs inflammables (vapeur d’essence, par exemple).
D Brancher le câble de masse sur la pièce le plus près possible de la
zone de soudage pour éviter le transport du courant sur une
longue distance par des chemins inconnus éventuels en provoquant des risques d’électrocution, d’étincelles et d’incendie.
D Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
D En cas de non utilisation, enlever la baguette d’électrode du porteélectrode ou couper le fil à la pointe de contact.
D Porter des vêtements de protection dépourvus d’huile tels que des
gants en cuir, une chemise en matériau lourd, des pantalons sans
revers, des chaussures hautes et un couvre chef.
D Avant de souder, retirer toute substance combustible de vos poches telles qu’un allumeur au butane ou des allumettes.
D Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
D Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
D Suivre les recommandations dans OSHA 1910.252(a)(2)(iv) et
NFPA 51B pour les travaux à chaud et avoir de la surveillance et un
extincteur à proximité.
DES PIECES DE METAL ou DES
SALETES peuvent provoquer des
blessures dans les yeux.
D Le soudage, l’écaillement, le passage de la pièce à la brosse en
fil de fer, et le meulage génèrent des étincelles et des particules
métalliques volantes. Pendant la période de refroidissement des
soudures, elles risquent de projeter du laitier.
D Porter des lunettes de sécurité avec écrans latéraux ou un écran
facial.
LES ACCUMULATIONS DE GAZ
risquent de provoquer des blessures
ou même la mort.
D Fermer l’alimentation du gaz comprimé en cas
de non utilisation.
D Veiller toujours à bien aérer les espaces confinés ou se servir d’un respirateur d’adduction
d’air homologué.
Les CHAMPS ÉLECTROMAGNÉTIQUES (CEM)
peuvent affecter les implants médicaux.
D Les porteurs de stimulateurs cardiaques et
autres implants médicaux doivent rester à
distance.
D Les porteurs d’implants médicaux doivent consulter leur
médecin et le fabricant du dispositif avant de s’approcher de la
zone où se déroule du soudage à l’arc, du soudage par points, du
gougeage, de la découpe plasma ou une opération de chauffage
par induction.
LE BRUIT peut endommager l’ouïe.
Le bruit des processus et des équipements peut
affecter l’ouïe.
D Porter des protections approuvées pour les
oreilles si le niveau sonore est trop élevé.
LES BOUTEILLES peuvent exploser
si elles sont endommagées.
Les bouteilles de gaz comprimé contiennent du gaz
sous haute pression. Si une bouteille est
endommagée, elle peut exploser. Du fait que les
bouteilles de gaz font normalement partie du
procédé de soudage, les manipuler avec
précaution.
D Protéger les bouteilles de gaz comprimé d’une chaleur excessive,
des chocs mécaniques, des dommages physiques, du laitier, des
flammes ouvertes, des étincelles et des arcs.
D Placer les bouteilles debout en les fixant dans un support stationnaire ou dans un porte-bouteilles pour les empêcher de tomber ou
de se renverser.
D Tenir les bouteilles éloignées des circuits de soudage ou autres
circuits électriques.
D Ne jamais placer une torche de soudage sur une bouteille à gaz.
D Une électrode de soudage ne doit jamais entrer en contact avec
une bouteille.
D Ne jamais souder une bouteille pressurisée − risque d’explosion.
D Utiliser seulement des bouteilles de gaz comprimé, régulateurs,
tuyaux et raccords convenables pour cette application spécifique;
les maintenir ainsi que les éléments associés en bon état.
D Détourner votre visage du détendeur-régulateur lorsque vous
ouvrez la soupape de la bouteille.
D Le couvercle du détendeur doit toujours être en place, sauf lorsque
la bouteille est utilisée ou qu’elle est reliée pour usage ultérieur.
D Utiliser les équipements corrects, les bonnes procédures et suffisamment de personnes pour soulever et déplacer les bouteilles.
D Lire et suivre les instructions sur les bouteilles de gaz comprimé,
l’équipement connexe et le dépliant P-1 de la CGA (Compressed
Gas Association) mentionné dans les principales normes de sécurité.
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance
Risque D’INCENDIE OU
D’EXPLOSION.
D Ne pas placer l’appareil sur, au-dessus ou
à proximité de surfaces inflammables.
D Ne pas installer l’appareil à proximité de produits inflammables.
D Ne pas surcharger l’installation électrique − s’assurer que
l’alimentation est correctement dimensionnée et protégée avant
de mettre l’appareil en service.
LA CHUTE DE L’ÉQUIPEMENT peut
provoquer des blessures.
D Utiliser l’anneau de levage uniquement pour
soulever l’appareil, NON PAS les chariots, les
bouteilles de gaz ou tout autre accessoire.
D Utiliser un équipement de levage de capacité
suffisante pour lever l’appareil.
D En utilisant des fourches de levage pour déplacer l’unité, s’assurer que les fourches sont suffisamment longues pour dépasser
du côté opposé de l’appareil.
D Tenir l’équipement (câbles et cordons) à distance des véhicules
mobiles lors de toute opération en hauteur.
D Suivre les consignes du Manuel des applications pour l’équation
de levage NIOSH révisée (Publication Nº94–110) lors du levage
manuelle de pièces ou équipements lourds.
L’EMPLOI
EXCESSIF
peut
SURCHAUFFER L’ÉQUIPEMENT.
D Prévoir une période de refroidissement ; respecter le cycle opératoire nominal.
D Réduire le courant ou le facteur de marche
avant de poursuivre le soudage.
D Ne pas obstruer les passages d’air du poste.
LES ÉTINCELLES PROJETÉES
peuvent provoquer des blessures.
D Porter un écran facial pour protéger le visage et
les yeux.
D Affûter l’électrode au tungstène uniquement à la
meuleuse dotée de protecteurs. Cette
manœuvre est à exécuter dans un endroit sûr
lorsque l’on porte l’équipement homologué de
protection du visage, des mains et du corps.
D Les étincelles risquent de causer un incendie − éloigner toute substance inflammable.
LES CHARGES ÉLECTROSTATIQUES peuvent endommager les circuits imprimés.
D Établir la connexion avec la barrette de terre
avant de manipuler des cartes ou des pièces.
D Utiliser des pochettes et des boîtes antistatiques pour stocker, déplacer ou expédier des
cartes de circuits imprimes.
OM-240 146 Page 7
Les PIÈCES MOBILES peuvent
causer des blessures.
LE
RAYONNEMENT
HAUTE
FRÉQUENCE
(H.F.)
risque
de
provoquer des interférences.
D Ne pas s’approcher des organes mobiles.
D Ne pas s’approcher des points de coincement
tels que des rouleaux de commande.
LES FILS DE SOUDAGE peuvent
provoquer des blessures.
D Ne pas appuyer sur la gâchette avant d’en
avoir reçu l’instruction.
D Ne pas diriger le pistolet vers soi, d’autres
personnes ou toute pièce mécanique en
engageant le fil de soudage.
Les PIÈCES MOBILES peuvent
causer des blessures.
D S’abstenir de toucher des organes mobiles tels
que des ventilateurs.
D Maintenir fermés et verrouillés les portes,
panneaux, recouvrements et dispositifs de
protection.
D Lorsque cela est nécessaire pour des travaux d’entretien et de
dépannage, faire retirer les portes, panneaux, recouvrements
ou dispositifs de protection uniquement par du personnel qualifié.
D Remettre les portes, panneaux, recouvrements ou dispositifs de
protection quand l’entretien est terminé et avant de rebrancher
l’alimentation électrique.
LIRE LES INSTRUCTIONS.
D Lire et appliquer les instructions sur les
étiquettes et le Mode d’emploi avant l’installation, l’utilisation ou l’entretien de l’appareil.
Lire les informations de sécurité au début du
manuel et dans chaque section.
D N’utiliser que les pièces de rechange recommandées par le
constructeur.
D Effectuer l’entretien en respectant les manuels d’utilisation, les
normes industrielles et les codes nationaux, d’état et locaux.
D Le rayonnement haute fréquence (H.F.) peut
provoquer des interférences avec les équipements de radio−navigation et de communication, les services de sécurité et les ordinateurs.
D Demander seulement à des personnes qualifiées familiarisées
avec des équipements électroniques de faire fonctionner l’installation.
D L’utilisateur est tenu de faire corriger rapidement par un électricien
qualifié les interférences résultant de l’installation.
D Si le FCC signale des interférences, arrêter immédiatement l’appareil.
D Effectuer régulièrement le contrôle et l’entretien de l’installation.
D Maintenir soigneusement fermés les portes et les panneaux des
sources de haute fréquence, maintenir les éclateurs à une distance correcte et utiliser une terre et un blindage pour réduire les
interférences éventuelles.
LE SOUDAGE À L’ARC risque de
provoquer des interférences.
D
D
D
D
D
D L’énergie électromagnétique risque de
provoquer des interférences pour l’équipement
électronique sensible tel que les ordinateurs et
l’équipement commandé par ordinateur tel que
les robots.
Veiller à ce que tout l’équipement de la zone de soudage soit
compatible électromagnétiquement.
Pour réduire la possibilité d’interférence, maintenir les câbles de
soudage aussi courts que possible, les grouper, et les poser
aussi bas que possible (ex. par terre).
Veiller à souder à une distance de 100 mètres de tout équipement électronique sensible.
Veiller à ce que ce poste de soudage soit posé et mis à la terre
conformément à ce mode d’emploi.
En cas d’interférences après avoir pris les mesures précédentes, il incombe à l’utilisateur de prendre des mesures supplémentaires telles que le déplacement du poste, l’utilisation de câbles blindés, l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone de travail.
2-4. Proposition californienne 65 Avertissements
Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des malformations congénitales et, dans certains cas, des cancers.
(Code de santé et de sécurité de Californie, chapitre 25249.5
et suivants)
Les batteries, les bornes et autres accessoires contiennent
du plomb et des composés à base de plomb, produits chimiques dont l’État de Californie reconnaît qu’ils provoquent des
cancers et des malformations congénitales ou autres
problèmes de procréation. Se laver les mains après manipulation.
Ce produit contient des produits chimiques, notamment du
plomb, dont l’État de Californie reconnaît qu’ils provoquent
OM-240 146 Page 8
des cancers, des malformations congénitales ou d’autres
problèmes de procréation. Se laver les mains après
utilisation.
Pour les moteurs à essence :
Les gaz d’échappement des moteurs contiennent des produits chimiques dont l’État de Californie reconnaît qu’ils
provoquent des cancers et des malformations congénitales
ou autres problèmes de procréation.
Pour les moteurs diesel :
Les gaz d’échappement des moteurs diesel et certains de
leurs composants sont reconnus par l’État de Californie comme provoquant des cancers et des malformations
congénitales ou autres problèmes de procréation.
2-5. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
de Global Engineering Documents (téléphone : 1-877-413-5184, site
Internet : www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, de Global
Engineering Documents (téléphone : 1-877-413-5184, site internet :
www.global.ihs.com).
National Electrical Code, NFPA Standard 70, de National Fire Protection Association, Quincy, MA 02269 (téléphone : 800-344-3555, site
Internet : www.nfpa.org et www.sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
de Compressed Gas Association, 4221 Walney Road, 5th Floor, Chantilly, VA 20151 (téléphone : 703-788-2700, site Internet :
www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, de Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (téléphone :
800-463-6727, site internet : www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, de American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (téléphone : 212-642-4900,
site Internet : www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, de National Fire Protection Association,
P.O. Box 9101, Quincy, MA 02269-9101 (téléphone : 617-770-3000,
site Internet : www.nfpa.org).
OSHA, Occupational Safety and Health Standards for General
Industry, Title 29, Code of Federal Regulations (CFR), Part 1910,
Subpart Q, and Part 1926, Subpart J, de U.S. Government Printing
Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA
15250-7954 (téléphone : 1-866-512-1800) (il y a 10 bureaux
régionaux−le téléphone de la région 5, Chicago, est 312-353-2220, site
Internet : www.osha.gov).
U.S. Consumer Product Safety Commission (CPSC), 4330 East West
Highway, Bethesda, MD 20814 (téléphone : 301-504-7923, site internet : www.cpsc.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The
National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30333 (télé[hone : 1-800-232-4636, site internet:
www.cdc.gov/NIOSH).
2-6. Informations relatives aux CEM
Le courant électrique qui traverse tout conducteur génère des champs
électromagnétiques (CEM) à certains endroits. Le courant de soudage
crée un CEM autour du circuit et du matériel de soudage. Les CEM
peuvent créer des interférences avec certains implants médicaux
comme des stimulateurs cardiaques. Des mesures de protection pour
les porteurs d’implants médicaux doivent être prises: par exemple, des
restrictions d’accès pour les passants ou une évaluation individuelle
des risques pour les soudeurs. Tous les soudeurs doivent appliquer les
procédures suivantes pour minimiser l’exposition aux CEM provenant
du circuit de soudage:
4. Maintenir la tête et le torse aussi loin que possible du matériel du
circuit de soudage.
1. Rassembler les câbles en les torsadant ou en les attachant avec
du ruban adhésif ou avec une housse.
2. Ne pas se tenir au milieu des câbles de soudage. Disposer les
câbles d’un côté et à distance de l’opérateur.
3. Ne pas courber et ne pas entourer les câbles autour de votre
corps.
En ce qui concerne les implants médicaux :
5. Connecter la pince sur la pièce aussi près que possible de la
soudure.
6. Ne pas travailler à proximité d’une source de soudage, ni
s’asseoir ou se pencher dessus.
7. Ne pas souder tout en portant la source de soudage ou le
dévidoir.
Les porteurs d’implants doivent d’abord consulter leur médecin avant
de s’approcher des opérations de soudage à l’arc, de soudage par
points, de gougeage, du coupage plasma ou de chauffage par induction. Si le médecin approuve, il est recommandé de suivre les
procédures précédentes.
OM-240 146 Page 9
OM-240 146 Page 10
SECTION 3 − INSTALLATION
. Appearance of actual unit may vary from unit shown in manual.
3-1. Specifications
Input
Power
Three
Phase
Rated
Welding
Output
675 A @
44 V DC,
100%
Duty
Cycle
Voltage
Range
10-44
Wire
Feed
Speed
Range**
Standard:
50-1400
ipm
(1.3-35.6
mpm)
Wire
Diameter
Range
.035-.062
in.
(0.8-1.6
mm)
Max
Open
Circuit
Voltage
DC
IP Rating
75
IP 21S
Amperes Input At Rated Load Output 60 Hz,
Three-Phase
230 V
400V
460 V
575 V
89
(0-1A*)
50
(0-1A*)
44
(0-1A*)
35
(0-1A*)
Input
KVA
Input
KW
35.5
(0.8*)
34
(0.17*)
*While idling; Input amperage fluctuates while idling and is always less than one Ampere. Use one Ampere for power efficiency calculations.
**Wire feed speed ranges are for GMAW welding. While pulse welding, wire feed speed ranges may be more limited.
3-2. Dimensions And Weight
Hole Layout Dimensions
A
A
17-3/32 in. (434 mm)
B
17-3/8 in. (441 mm)
C
19-3/32 in. (485 mm)
D
16-3/32 in. (409 mm)
E
1/2 in. (13 mm)
E
22 in.
(559 mm)
41 in.
(1041 mm)
C
B
Weight
215 lb (98 kg) Net
232 lb (105 kg) Ship
D
15-1/2 in.
(394 mm)
Ref. 802 913-B
OM-240 146 Page 11
3-3. Duty Cycle And Overheating
Duty Cycle is percentage of 10 minutes that unit can weld at rated load
without overheating.
If unit overheats, thermostat(s)
opens, output stops, and cooling
fan runs. Wait fifteen minutes for
unit to cool. Reduce amperage or
duty cycle before welding.
NOTICE − Exceeding duty cycle
can damage unit and void warranty.
100% Duty Cycle At 675 Amperes
Continuous Welding
Overheating
A/V
0
15
OR
Reduce Duty Cycle
Minutes
duty1 4/95 − 206 789-A
3-4. Volt-Ampere Curves
80
Volt-ampere curves show minimum
and maximum voltage and amperage output capabilities of unit.
Curves of other settings fall between curves shown.
70
. This volt-ampere curve repre-
CV MODE
sents the dynamic output of the
unit with a static load.
60
VOLTAGE
50
40
30
20
10
0
0
100
200
300
400
500
AMPERES
600
700
800
900
1000
va_curve1 4/95 − 221 502-A
OM-240 146 Page 12
3-5. Serial Number And Rating Label Location
The serial number and rating information for this product is located on the front. Use rating label to determine input power requirements and/or rated
output. For future reference, write serial number in space provided on back cover of this manual.
3-6. Selecting A Location
Movement
!
Tipping
Do not move or operate
unit where it could tip.
2
OR
1
Location
!
Special installation may be required where gasoline or volatile
liquids are present − see NEC Article 511 or CEC Section 20.
3
!
Do not stack units. Beware of
tipping.
1
Lifting Forks
Use lifting forks to move unit.
Extend forks beyond opposite side
of unit.
2
Hand Cart
Use cart or similar device to move
unit.
18 in.
(460 mm)
3
Line Disconnect Device
Locate unit near correct input
power supply.
18 in.
(460 mm)
loc_2 3/96 -Ref. 802 913-B
3-7. Connection Diagram
. The proper interface kit must
2
be installed in the welding power source/interface unit to allow
it to be connected to the robot.
5
3
1
4
1
6
7
12
Robot (Will Vary According To
Application)
2 Motor/Drive Assembly
3 Gas Cylinder
4 Gas Hose
5 Robot Control
6 Robot Input/Output Cable
7 Gas And Motor Control Cable
8 Welding Power
Source/Interface Unit
9 Negative (−) Weld Cable
10 Workpiece
11 Voltage Sensing Lead
(Optional)
. Positive
(+) voltage sensing
lead is contained in the motor
cable.
10
9
8
12 Positive (+) Weld Cable
11
Ref. 802 913-B / Ref. 801 915-A
OM-240 146 Page 13
3-8. Optional Tandem Connection Diagram
5
4
3
2
6
7
13
8
Î
12
9
1
10
Î
14
8
9
11
805 329-A
. The
1
2
3
4
proper interface kit must be
installed in the welding power
source/interface unit to allow it to be
connected to the robot.
Robot (Will Vary According To
Application)
Motor/Drive Assembly (2)
Gas Cylinder
Gas Hose (2)
OM-240 146 Page 14
5
6
7
8
Robot Control
E-Stop Cable (2)
Gas And Motor Control Cable (2)
Welding Power Source/Interface
Unit (2)
9 Negative (−) Weld Cable (2)
10 Workpiece
11 Voltage Sensing Lead (2)
Recommended for Accu-pulse and RMD
(optional).
. Positive (+) voltage sensing lead is
contained in the motor cable.
12 Positive (+) Weld Cable (2)
13 Devicenet Robot/Welder Control
Cable (2)
14 Tandem Interconnect Cable
3-9. Rear Panel Receptacles And Supplementary Protectors
1
115 V 10 A AC Receptacle RC2
Receptacle
supplies
60
Hz
single-phase power. Maximum output
from RC2 is limited by supplementary
protector CB1 to 10 amps.
4
5
8
6
1
2
3
Supplementary Protector CB1
Supplementary Protector CB2
2
CB1 protects 115 volt receptacle RC2
from overload. If CB1 opens, RC2 does
not work.
3
CB2 protects the wirefeed motor from
overload. If CB2 opens, the wirefeeder
does not work.
. Press
button to reset breaker. If
breaker continue to open, contact a
Factory Authorized Service Agent.
4
7
Wirefeed/Gas Receptacle RC8
Use receptacle to connect gas and
motor control cable to power source
(see Sections 3-7 and 8 for additional
information).
5
Peripheral Receptacle RC25
. RC25 is not used with Devicenet.
6
E-Stop Receptacle RC
A short across the two sockets allows
unit to weld.
7
Devicenet Receptacle RC
Network control cable connection for robot/welder communication.
8
Optional Tandem Receptacle
Connect one end of a tandem
interconnect cable to this receptacle
and the remaing end of the cable to
another tandem ready Auto-Axcess
welding power source.
Ref. 805 224-A
OM-240 146 Page 15
3-10. Connecting To Weld Terminals
. If using an electrode negative (straight polarity)
process, the volt sense lead must be connected
to the work.
1
2
3
6
Do not place
anything between
weld cable terminal
and copper bar.
4
5
Tools Needed:
3/4 in. (19 mm)
Correct Installation
Incorrect Installation
Ref. 802 913-B / 803 778-A
!
!
Turn off power before connecting to
weld output terminals.
Failure to properly connect weld
cables may cause excessive heat
and start a fire, or damage your
machine.
Determine total cable length in weld circuit
(both positive and negative cables
combined) and maximum welding
amperes. See Section 3-12 to select proper
OM-240 146 Page 16
cable size.
1
2
Positive (+) Weld Output Terminal
Negative (−) Weld Output Terminal
Connect positive weld cable to Positive (+)
weld terminal and negative (−) cable to
Negative weld terminal.
3
Weld Output Terminal
4
5
Supplied Weld Output Terminal Nut
Weld Cable Terminal
6
Copper Bar
Remove supplied nut from weld output
terminal. Slide weld cable terminal onto
weld output terminal and secure with nut so
that weld cable terminal is tight against
copper bar. Do not place anything
between weld cable terminal and copper
bar. Make sure that the surfaces of the
weld cable terminal and copper bar are
clean.
3-11. Selecting Weld Cable Sizes*
NOTICE − The Total Cable Length in Weld Circuit (see table below) is the combined length of both weld cables. For example, if the power source is
100 ft (30 m) from the workpiece, the total cable length in the weld circuit is 200 ft (2 cables x 100 ft). Use the 200 ft (60 m) column to determine cable
size.
Weld Cable Size*** and Total Cable (Copper) Length in Weld Circuit Not Exceeding****
100 ft (30 m) or Less
150 ft
(45 m)
200 ft
(60 m)
250 ft
(70 m)
300 ft
(90 m)
350 ft
(105 m)
400 ft
(120 m)
Weld Output Terminals
!
!
Turn off power before
connecting to weld output terminals.
Welding
Amperes**
10 − 60%
Duty Cycle
60 − 100%
Duty Cycle
100
4 (20)
4 (20)
4 (20)
3 (30)
2 (35)
1 (50)
1/0 (60)
1/0 (60)
150
3 (30)
3 (30)
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
3/0 (95)
200
3 (30)
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0
(120)
4/0
(120)
250
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0
(120)
2 ea. 2/0
(2x70)
2 ea. 2/0
(2x70)
300
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0
(120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 3/0
(2x95)
350
1/0 (60)
2/0 (70)
3/0 (95)
4/0
(120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
400
1/0 (60)
2/0 (70)
3/0 (95)
4/0
(120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
2 ea. 4/0
(2x120)
500
2/0 (70)
3/0 (95)
4/0
(120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
3 ea. 3/0
(3x95)
600
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
3 ea. 4/0
(3x120)
3 ea. 4/0
(3x120)
700
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
3 ea. 4/0
(3x120)
3 ea. 4/0
(3x120)
4 ea. 4/0
(4x120)
800
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 4/0
(3x120)
3 ea. 4/0
(3x120)
4 ea. 4/0
(4x120)
4 ea. 4/0
(4x120)
900
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
1000
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
1250
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
4 ea. 3/0
(4x95)
10 − 100% Duty Cycle
Do not use worn, damaged, undersized, or
poorly spliced cables.
Positive
)
* This
Negative
*
Ref. 802 914-B
chart is a general guideline and may not suit all applications. If cable overheats, use next size larger cable.
**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.
( ) = mm2 for metric use
***For distances longer than those shown in this guide, call a factory applications rep. at 920-735-4505 (Miller) or 1-800-332-3281 (Hobart)
Ref. S-0007-G 2009−08
. In pulse welding applications using inverter power sources, peak currents can result in extreme voltage drops producing poor welding characteris-
tics with undersized cables. A recommendation for weld cable size is a minimum of 2/0 for 300 ampere welding power sources and 4/0 for 450
ampere welding power sources when total cable length is less than 100 ft (30m).
OM-240 146 Page 17
3-12. Devicenet Receptacle
Socket
C
D
B
A
E
Socket Information
A
Chassis ground.
B
+24 volts DC; available current is 1 ampere.
C
+24 volts DC common.
D
CAN H.
E
CAN L.
Ref. 804 578-A
3-13. Motor Control Receptacle Functions
G
J
K
Socket
C
A
F
E
H
D
B
Ref. 804 578-A
Socket Information
A
Not used.
B
Motor negative (−).
C
Tach A, 0 volts = low and 3.5 volts = high.
D
Motor positive (+).
E
Tach common.
F
Gas valve, +40 volts DC when valve is on with respect to
socket K.
G
Electrode sense.
H
Tach +5 volts DC with respect to socket E.
J
Tach B, 0 volts = low and 3.5 volts = high.
K
Gas valve.
3-14. E-Stop Receptacle Functions
A
B
Ref. 804 578-A
OM-240 146 Page 18
Socket
Socket Information
A
A short to socket B allows unit to weld.
B
A short to socket A allows unit to weld.
3-15. Tandem Receptacle
Socket
A
B
C
E
D
Socket Information
A
Gnd.
B
Peak enable/disable, input (high).
C
Peak enable/disable, output.
D
Peak enable/disable, input (low).
E
Not used.
Ref. 804 578-A
3-16. Electrical Service Guide
Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These
recommendations are for a dedicated circuit sized for the rated output and duty cycle of the welding power source.
In dedicated circuit installations, the National Electrical Code (NEC) allows the receptacle or conductor rating to be less than the rating
of the circuit protection device. All components of the circuit must be physically compatible. See NEC articles 210.21, 630.11, and
630.12.
NOTICE − INCORRECT INPUT POWER can damage this welding power source. This welding power source requires a CONTINUOUS supply of
input power at rated frequency(+10%) and voltage (+10%). Phase to ground voltage shall not exceed +10% of rated input voltage. Do not use a generator with automatic idle device (that idles engine when no load is sensed) to supply input power to this welding power source.
. Actual input voltage should not exceed ± 10% of indicated required input voltage. If actual input voltage is outside of this range, output may not
be available.
60 Hz Three Phase
Input Voltage (V)
230
400
460
575
Input Amperes (A) At Rated Output
89
50
44
35
Time-Delay Fuses 2
110
60
50
40
3
125
80
70
50
3
6
8
8
173
(53)
275
(84)
231
(70)
361
(110)
6
8
8
10
Max Recommended Standard Fuse Rating In Amperes 1
Normal Operating Fuses
Min Input Conductor Size In AWG 4
Max Recommended Input Conductor Length In Feet (Meters)
Min Grounding Conductor Size In AWG 4
Elec Serv 2011−08
Reference: 2011 National Electrical Code (NEC) (including article 630)
1 If a circuit breaker is used in place of a fuse, choose a circuit breaker with time-current curves comparable to the recommended fuse.
2 “Time-Delay” fuses are UL class “RK5” . See UL 248.
3 “Normal Operating” (general purpose - no intentional delay) fuses are UL class “K5” (up to and including 60 amps), and UL class “H” ( 65 amps and
above).
4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table
310.15(B)(16). If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable
requirements.
OM-240 146 Page 19
3-17. Connecting Input Power
3
= GND/PE Earth Ground
5
8
3
2
L1
4
L2
7
6
WARNING
L3
1
ELECTRIC SHOCK can kill;
SIGNIFICANT DC VOLTAGE
exists after removal of
input power.
S Always wait 5 minutes after power
is turned off before working on unit.
S Check input capacitor voltage, and
be sure it is near 0 before touching
any parts.
Read Owner’s Manual.
Three−Phase Input Connection
Route input power cable
through tubing inside unit.
L3
L2
L1
Route ground conductor through
current transducer to ground terminal.
Tools Needed:
GND/PE
GND/PE
218005−C
5/16 in.
802 915-A / Ref. 803 766-A / 218 005-C
!
!
!
Turn Off welding power source, and
check voltage on input capacitors
according to Section 7-3 before
proceeding.
applicable, use lugs of proper amperage
capacity and correct hole size.
Disconnect
Device
Connections
Welding Power Source Input Power
Connections
3
Disconnect Device (switch shown in
the OFF position)
Installation must meet all National
and Local Codes − have only qualified
persons make this installation.
2
Disconnect and lockout/tagout input
power before connecting input
conductors from unit.
!
Make input power connections to the
welding power source first.
!
Always
connect
green
or
green/yellow conductor to supply
grounding terminal first, and never to
a line terminal.
1
Input Power Conductors (Customer
Supplied Cord)
Select size and length of conductors using
Section 3-16. Conductors must comply with
national, state, and local electrical codes. If
OM-240 146 Page 20
Input
Power
4
Install strain relief of proper size for unit and
input conductors. Route conductors (cord)
through strain relief and tighten screws.
Green Or Green/Yellow Grounding
Conductor
5
Disconnect Device Grounding Terminal
6
Input Conductors (L1, L2 And L3)
S Use large strain relief for input conductor
size 8 and larger.
7
Disconnect Device Line Terminals
Strain Relief
S Use small strain relief with reducing
washers for input conductor size 10.
Connect green or green/yellow grounding
conductor to disconnect device grounding
terminal first.
Connect input conductors as shown in
illustration.
Connect input conductors L1, L2, and L3 to
disconnect device line terminals.
Route green or green/yellow grounding
conductor through current transducer and
connect to welding power source grounding
terminal first. Then connect input conductors
L1, L2, and L3 to welding power source line
terminals.
Reinstall side panel onto welding power
source.
8
Over-Current Protection
Select type and size of over-current protection using Section 3-16 (fused disconnect
switch shown).
Close and secure door on disconnect device.
Remove lockout/tagout device, and place
switch in the On position.
3-18. Remote Program Select
. Remote Program Select is factory set to “On”. WaveWriter or File Management software is required to turn this function “Off”.
When Remote Program Select is On, a robot pendant may be used to select programs. When Off, program selection
must be done from the welding power source front panel.
3-19. Remote Program Setting
When Remote Program Select is “On”, program selection will be determined by remote input through Devicenet once
a weld is initiated. Prior to welding, program selection can be done in a normal manner from the welding power source
front control panel.
3-20. Touch Sensor Operation
The touch sensor feature allows the robot to locate a weldment using the wire feed system and welding power source.
The weld output terminals provide a path for touch sensor voltage when this feature is turned on at the peripheral
receptacle. Turning on touch sensor causes a DC voltage to be present on the welding wire. When welding wire
touches the weldment, the voltage sensing circuit closes, and a digital output signal is sent to the robot control
indicating weldment detection. Touch sensor DC voltage on the welding wire is 80 volts DC. As soon as touch sensor
turns on, WIRE LIVE appears on the front panel display.
OM-240 146 Page 21
SECTION 4 − OPERATION
4-1. Operational Terms
The following is a list of terms and their definitions as they apply to this interface unit:
General Terms:
AccuCurve
CV Pulse process using a pulse waveform with modified curves at particular locations within the waveform. Has
a distinguished change in arc characteristics. Front panel display is ACCU − CURV.
Accu-pulse
Pulse process utilizing constant current ramps with constant voltage control of peaks and backgrounds.
Adaptive response is controlled by peak and minimum current levels. Benefits are shorter arc lengths, better
puddle control, more tolerant of tip-to-work variation, less audible noise, no arc wandering, allows weld to fill in
at toes increasing travel speed and deposition, and more tolerant to poor fit up and gaps.
Accuspeed (optional)
CV Pulse process designed for high travel speeds. Typically used in Robotic applications. Arc is designed to be
tight and fast. Front panel display is ACCU − SPED.
Adjust
Control knob used to change or set parameters and functions.
Amps
Indicates average amperage while welding and 3 seconds hold value at end of weld.
Arc Adjust
Term used to represent arc length adjustments in pulse programs. Increasing Arc Adjust increases the actual
arc length. Likewise, decreasing arc adjust shortens arc length. Arc Adjust is replaced by volts in MIG
programs.
Arc Control
Pressing this button will allow setting of inductance in MIG mode and sharp arc in pulse, Accu-pulse, and RMD
(optional).
Arc Length
Distance from end of wire electrode to workpiece.
Auto Thread
Method of jogging wire without holding jog or trigger switch. Pressing Jog and Retract simultaneously will
automatically feed wire. Default setting is 72 inches at a feed rate of 700 ipm. Pressing jog, purge, or trigger
switch will terminate the auto-threading feature. These values can be changed using a PDA with File
Management/WaveWriter software.
Crater
Allows setting of voltage/arc adjust, wire feed rate, and time value for arc ends (only available on Auto Axcess
models in the Arc On and Analog input or the Arc On and No Analog input modes, and can only be set with the
optional PDA with File Management software).
Gas Type
Selection of shielding gas being used in application.
Inductance
In short circuit GMAW welding, an increase in inductance will decrease the number of short circuit transfers per
second (provided no other changes are made) and increase the arc-on time. The increased arc-on time makes
the welding puddle more fluid.
MIG
CV weld process with individual settings of voltage and wire speed.
Postflow
Setting a time value for gas flow after arc end (only available on Auto Axcess models in the Arc On and Analog
input or the Arc On and No Analog input modes, and can only be set with the optional PDA with File Management software).
Preflow
Setting a time value for gas flow prior to arc start (only available on Auto Axcess models in the Arc On and
Analog input or the Arc On and No Analog input modes, and can only be set with the optional PDA with File
Management software).
Process
A selection made for MIG, Pulse, Accu-pulse, and RMD (optional).
Process Set Up
Selection procedure for entering program.
Program
Eight active slots for selection of various processes, wire types, and parameters.
Program Load
Enters selected program information (process, wire type, gas, etc.) into program slot (1-8).
Pulse
Conventional pulse program using peak, background, pulse width, frequency, and peak voltage as factory
taught data. Adaptive method is controlled by frequency adjustment.
Retract
Sequence function that allows the wire to move back towards the contact tip when a welding operation is
completed. Setting is both speed (IPM) and time (sec), (only available on Auto Axcess models in the Arc On
and Analog input or the Arc On and No Analog input modes, and can only be set with the optional PDA with File
Management software).
RMD (optional)
RMD refers to Regulated Metal Deposition. A precisely controlled short-circuit transfer. Benefits of RMD are well
suited to thin materials, improves gap filling and spatter reduction. Provides less heat input into workpiece,
minimizes distortion and allows use of larger diameter wire on thin gauge materials.
Sequence
Selecting Sequence will allow setting of preflow, start, crater, postflow, and retract times and parameters (only
available on Auto Axcess models in the Arc On and Analog input or the Arc On and No Analog input modes).
Sharp Arc
In pulse and Accu-pulse mode this adjustment changes the arc cone by adjusting the preprogrammed factory
pulse data. In RMD (optional) this control will affect the arc in much the same way as inductance.
Start
Provides voltage/arc adjust, wire feed rate, and time value for modified arc starts (only available on Auto Axcess
models in the Arc On and Analog input or the Arc On and No Analog input modes, and can only be set with the
optional PDA with File Management software).
Synergic
Synergic refers to the unit’s ability to use preprogrammed pulse parameters to determine the actual pulse
settings of Peak Amperage, Background Amperage, Pulse Frequency and Pulse Width at any specific wire feed
speed setting.
OM-240 146 Page 22
4-1 . Operational Terms (Continued)
Time
Indicates time values being set for timed functions (e.g. Preflow, Postflow which are only available in the Arc On
and Analog input or the Arc On and No Analog input modes).
Volts
Preset voltage in MIG mode at idle, actual voltage while welding, and 3 seconds hold value at end of weld.
Weld
Sequence function that allows for a timed weld operation [(0 to 999 seconds) only available on Auto Axcess
models in the Arc On and Analog input or the Arc On and No Analog input modes, and can only be set with the
optional PDA with File Management software].
WFS
Term used to represent wire feed speed. In MIG mode, wire feed setting is independent of voltage setting. In
pulse, Accu-pulse, and RMD (optional) adjusting wire feed speed also increases power level on wire electrode
(one knob control).
Wire Type
Selection of wire type by alloys and classification.
OM-240 146 Page 23
4-2. Front Panel Controls (See Section 4-3)
15
14
13
1
4
12
Program
Volts
Arc Adjust
Wire Speed
3
Amps
11
Process
Wirefeed
Wire Type
Gas Type
Gas
Contactor
10
5
6
8
7
Setup
Adjust
Arc Control
9
2
. When an LED is lit, it means the related function is active.
198 993
1 Program Display
Displays the number of the active program.
2 Adjust Knob
Turn the Adjust knob to change program
number, Setup, Arc Control, and weld
parameters.
3 Program Push Button LED
The LED lights when the Program Push
Button is active.
4 Program Push Button
Press push button (LED lights) and turn Adjust
knob to select active program.
The letter C is displayed with the program
number if the program has been changed from
the factory settings using the optional PDA
with File Management/WaveWriter software
(see File Management/WaveWriter Owner’s
Manual).
. The program cannot be changed through
the front panel while welding.
Press and hold button to see program name.
Custom programs are named using optional
OM-240 146 Page 24
PDA with File Management/WaveWriter
software. Program name is shown in upper
and lower displays (items 13 and 15).
5
Setup Mode Indicators
The lit LED indicates which setup mode is
active. Setup mode parameters are shown in
Display Windows (see Items 13 and 15).
Process LED
When this LED is lit, turn the Adjust knob to
select the desired weld process. Choices
include pulse welding (displayed as PULS),
Accu-pulse (ACCU), MIG welding (MIG), and
RMD [Regulated Metal Deposition (optional)].
Wire Type LED
When this LED is lit, turn the Adjust knob to
select the desired wire type, wire alloy, and
size. Wire type and size choices vary
according to the selected weld process.
Choices may include steel (displayed as
STL), stainless steel (SS), metal core
(MCOR), aluminum (ALUM). See Table 4-1
for all wire abbreviations.
Gas Type LED
When this LED is lit, turn the Adjust knob to
select the desired weld gas. Gas type choices
vary according to the selected weld process.
See Table 4-1 for all gas abbreviations.
6
Setup Push Button LED
The LED lights to indicate one of the setup
modes is active.
7
Setup Push Button
Press button to select Process, Wire Type,
Wire Diameter, or Gas Type parameters.
. In order for selections to be retained in
memory, the Setup push button must be
pressed six times before any other push
button is pressed: once to select Process,
again to select Wire Type, again to select
Wire Alloy, again to select Wire Size,
again to select Gas Type, and a sixth time
to store selections in memory. The
displays will temporarily show “PROG
LOAD” to indicate the data is being stored
in memory.
4-3. Front Panel Controls - Continued (See Section 4-2)
8
11 Wire Speed And Amps LED’s
Arc Control LED
The LED lights to indicate the Arc Control
button is active. Light goes out when button is
inactive.
9
Arc Control Push Button
This push button allows fine tuning inductance
for MIG programs, and Arc Control for
programs other than MIG. When the push
button is pressed, the upper display (item 15)
shows INDU for inductance, or ARC for Arc
Control to indicate which parameter is
selected for change. The range of possible
values is 0-99 for inductance, and 0-50 for arc
control. Turn the Adjust knob to change the
parameter value. Press button to deactivate
arc control mode (LED goes out).
10 Wire Feed/Gas/Contactor LEDs
The Wirefeed LED lights when the wire feeder
is energized. For example, when the front
panel Jog or Retract button is pressed, the
Wirefeed LED lights.
The Gas LED lights when the gas valve is
energized.
The Contactor LED lights when the output
contactor is energized, making the weld
output terminals live.
The lit LED indicates whether wire speed or
amps are being displayed.
12 Wire Feed Speed/Amps Display Push
Button
13 Lower Display
was used to set the unit in the ”Display
Command Values” mode. In the Display
Command Values mode, command
values are displayed while welding.
. If a PDA with File Management/WaveWriter
Press Wire Feed Speed/Amps Display button
to show weld amperage or wire feed speed in
lower display (the applicable LED under the
lower display lights to indicate which is
shown). When welding, actual value is shown.
If amperage was selected for display, the unit
will show actual welding amperage prior to
and while welding unless the the unit is in
Display Command Values mode. Only wire
speed command will be displayed while
welding if the unit is set in Display Command
Values mode, even if the Wire Feed
Speed/Amps Display button is pressed.
. Displays show actual or command values
as determined by configuration menu
when using a PDA with File Management/
WaveWriter software. Command values
are displayed prior to welding and actual
values are displayed while welding unless
a PDA with File Management software
software is used to change wire feed units
(IPM, MPM) or display welding information
(command or actual),save the changes and
then turn the power to the unit off and then
on again for the changes to be carried out
by the unit.
14 Volts And Arc Adjust LED’s
The lit LED indicates whether voltage or arc
length is being displayed.
15 Upper Display
The upper display shows different information
depending on the active function of the unit
and the weld process being used. When the
display shows voltage (for a MIG process),
the Volts LED lights. When it shows arc adjust
[for a pulsed and RMD (optional) weld
process], the Arc Adjust LED lights. However,
during any weld process (MIG and pulse), the
unit will display actual arc voltage unless a
PDA with File Management/WaveWriter
software has set the unit in the ”Display
Command Values” mode.
Table 4-1. Welding Wire And Gas Abbreviations*
Wire Description
Wire Abbreviation
Alloy Type
Gas Type
Gas Abbreviation
Steel
STL
E70, E100, E120
100% CO2,
90% Argon/10% CO2,
85% Argon/15% CO2,
75% Argon/25% CO2,
95% Argon/5% CO2,
95% Argon /5% O2,
98% Argon/2% O2
CO2
C10
C15
C25
C5
OX5
OX2
Stainless Steel
SS
308, 309, 312, 316
98% Argon, 2% O2
(81Ar/18HE/1CO2
Accu-pulse)
90HE/7-1/2Ar/2-1/2CO 2
MIG/RMD/Accu-pulse)
OX2
Tri Gas
71, 76, 86R, 409,
439
90% Argon/10% CO2
C10
98% Argon/2% O2
OX2
4XXX, 5XXX
100% Argon
ARGN
Cored Tubular Wire
Aluminum
MCOR
ALUM
Tri Gas
* Not all wire types may be available with your unit.
OM-240 146 Page 25
4-4. Front Panel Switches
6
3
4
1
8
5
9
7
Ref. 802 914-A
2
1
Power Switch
Turns unit On or Off.
The power-up sequence may last up to 30
seconds before the unit is ready to weld.
During power-up, the front panel will display
messages indicating the status of the unit. The
first message is:
AUTO
675
AUTO 675 indicates the software being
loaded.
2
Contactor LED
Contactor LED illuminates when weld output is
energized.
Wirefeed LED
Wirefeed LED illuminates when wire feeds or
retracts.
7
Retract Push Button
Press button to retract wire. Wirefeed LED
illuminates when Retract push button is
pressed.
NET
WAIT
3
NET WAIT is an abbreviation for ”network
updating” and means the internal control
network is powering up. The next message is
4
Gas LED illuminates when Purge push button
is pressed.
Auto-Threading feature is activated by
pressing the Jog and Retract buttons
simultaneously. Pressing the Jog, Purge, or
trigger switch will turn off the Auto-Threading
feature.
DTEC ROBT (Robot Type)
5
Jog Push Button
8
PDA Port
The final message is
Press button to jog wire.
9
PC Port
OM-240 146 Page 26
Purge Push Button
6
Press button to purge gas line.
Gas LED
4-5. Reset Mode
. Reset mode is not active when
Program Lock is enabled.
The reset mode allows the operator to
reload factory program settings for all
eight active programs in the unit.
RST
. System configuration data will be
NO
lost during the Reset operation.
Enter reset mode by turning power On and pressing the Program
Push Button until the RST NO message is displayed. RST NO
message will not display until after the power-up sequence is
completed (approximately 20 seconds).
RST
RST
CYCL
YES
YES
PWR
Rotate Adjust knob to change NO
to YES.
Press the Arc Control button to
confirm the reset.
Cycl Pwr message appears on the display
when programs complete loading.
The reset message is displayed for
2 seconds while factory program
settings are being reloaded.
Turn power off, wait 10 seconds, and turn
power back on again to complete the reset
operation.
During the reset mode the following
factory default programs are loaded
into the unit:
Program 1
Pulse
.035 Mild Steel
90% Argon, 10% CO2
Program 2
MIG
.035 Mild Steel
75% Argon, 25% CO2
Program 3
Accu-pulse
.035 Mild Steel
90% Argon, 10% O2
Program 4
Pulse
.045 Mild Steel
90% Argon, 10% CO2
Program 5
MIG
.045 Mild Steel
75% Argon, 25% CO2
Program 6
Accu-pulse
.045 Mild Steel
90% Argon, 10% O2
Program 7
Pulse
.052 Mild Steel
90% Argon, 10% CO2
Program 8
MIG
.052 Mild Steel
75% Argon, 25% CO2
. After
Reset is complete, be sure to load
appropriate programs that contain the
correct wire size, process, and shielding gas
for the welding operation
198 993 / 803 246-B
OM-240 146 Page 27
SECTION 5 − MAINTENANCE
5-1. Routine Maintenance
!
n = Check
Z = Change
~ = Clean
* To be done by Factory Authorized Service Agent
Every
3
Months
l Unreadable Labels
~ Weld Terminals
nl Cords
nl Gun Cables
Every
6
Months
Disconnect power
before maintaining.
. Maintain more often
during severe conditions.
l = Replace
l Damaged Gas Hose
Reference
nl Weld Cables
OR
~ Drive Rolls
~ Inside Unit
5-2. Blowing Out Inside Of Unit
!
Do not remove case when
blowing out inside of unit.
To blow out unit, direct airflow
through front and back louvers as
shown.
Ref. 802 913-B
OM-240 146 Page 28
SECTION 6 − SAFETY PRECAUTIONS FOR SERVICING
Protect yourself and others from injury — read and follow these precautions.
6-1. Symbol Usage
OM-240 146F 2010−11, safety_stm 2010−03
DANGER! − Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in the text.
NOTICE − Indicates statements not related to personal injury.
. Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the
hazards.
6-2. Servicing Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard.
Only qualified persons should test, maintain, and repair this
unit.
FLYING METAL or DIRT can injure eyes.
D Wear safety glasses with side shields or face
shield during servicing.
D Be careful not to short metal tools, parts, or
wires together during testing and servicing.
During servicing, keep everybody, especially children, away.
ELECTRIC SHOCK can kill.
D Do not touch live electrical parts.
D Turn Off welding power source and wire feeder
and disconnect and lockout input power using
line disconnect switch, circuit breakers, or by removing plug from receptacle, or stop engine before servicing unless the procedure specifically requires an energized unit.
D
Insulate yourself from ground by standing or working on dry insulating mats big enough to prevent contact with the ground.
D
Do not leave live unit unattended.
D
If this procedure requires an energized unit, have only personnel
familiar with and following standard safety practices do the job.
D
When testing a live unit, use the one-hand method. Do not put both
hands inside unit. Keep one hand free.
D
Disconnect input power conductors from deenergized supply line
BEFORE moving a welding power source.
SIGNIFICANT DC VOLTAGE exists in inverter welding power sources AFTER removal of input power.
D
Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Troubleshooting Section before touching any parts.
HOT PARTS can burn.
D Do not touch hot parts bare handed.
D Allow cooling period before working on
equipment.
D To handle hot parts, use proper tools and/or
wear heavy, insulated welding gloves and
clothing to prevent burns.
EXPLODING PARTS can injure.
D Failed parts can explode or cause other parts to
explode when power is applied to inverters.
D Always wear a face shield and long sleeves
when servicing inverters.
SHOCK HAZARD from testing.
D Turn Off welding power source and wire feeder
or stop engine before making or changing meter lead connections.
D Use at least one meter lead that has a selfretaining spring clip such as an alligator clip.
D Read instructions for test equipment.
STATIC (ESD) can damage PC boards.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
FIRE OR EXPLOSION hazard.
D Do not place unit on, over, or near combustible
surfaces.
D Do not service unit near flammables.
FALLING EQUIPMENT can injure.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are long enough to
extend beyond opposite side of unit.
D Follow the guidelines in the Applications Manual for the Revised
NIOSH Lifting Equation (Publication No. 94−110) when manually lifting heavy parts or equipment.
OM-240 146 Page 29
MOVING PARTS can injure.
D Keep away from moving parts such as fans.
D Keep away from pinch points such as drive
rolls.
D Have only qualified persons remove doors,
panels, covers, or guards for maintenance and
troubleshooting as necessary.
D Keep hands, hair, loose clothing, and tools
away from moving parts.
D Reinstall doors, panels, covers, or guards
when maintenance is finished and before reconnecting input power.
ELECTRIC AND MAGNETIC FIELDS (EMF)
can affect Implanted Medical Devices.
D Wearers of Pacemakers and other Implanted
Medical Devices should keep away from servicing areas until consulting their doctor and the
device manufacturer.
OVERUSE can cause OVERHEATING.
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
H.F. RADIATION can cause interference.
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment install, test, and service
H.F. producing units.
D The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
D If notified by the FCC about interference, stop using the
equipment at once.
D Have the installation regularly checked and maintained.
D Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
READ INSTRUCTIONS.
D Use Testing Booklet (Part No. 150 853) when
servicing this unit.
D Consult the Owner’s Manual for welding safety
precautions.
D Use only genuine replacement parts from the manufacturer.
D Read and follow all labels and the Technical Manual carefully before installing, operating, or servicing unit. Read the safety information at the beginning of the manual and in each section.
6-3. California Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
For Gasoline Engines:
Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
For Diesel Engines:
Diesel engine exhaust and some of its constituents are
known to the State of California to cause cancer, birth
defects, and other reproductive harm.
This product contains chemicals, including lead, known to
the state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after use.
6-4. EMF Information
Electric current flowing through any conductor causes localized electric
and magnetic fields (EMF). Welding current creates an EMF field
around the welding circuit and welding equipment. EMF fields may interfere with some medical implants, e.g. pacemakers. Protective
measures for persons wearing medical implants have to be taken. For
example, access restrictions for passers−by or individual risk assessment for welders. All welders should use the following procedures in
order to minimize exposure to EMF fields from the welding circuit:
1. Keep cables close together by twisting or taping them, or using a
cable cover.
2. Do not place your body between welding cables. Arrange cables
to one side and away from the operator.
3. Do not coil or drape cables around your body.
OM-240 146 Page 30
4. Keep head and trunk as far away from the equipment in the
welding circuit as possible.
5. Connect work clamp to workpiece as close to the weld as
possible.
6. Do not work next to, sit or lean on the welding power source.
7. Do not weld whilst carrying the welding power source or wire
feeder.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recommended.
SECTION 7 − TROUBLESHOOTING
7-1. Set Value Mode
Program
Volts
Arc Adjust
Wire Speed
1
Amps
Process
Wirefeed
Wire Type
Gas Type
Gas
Contactor
Setup
Adjust
Arc Control
4
2
3
The Set Value mode is a troubleshooting tool
that allows certain robot command values to
be manually over-ridden.
1
Setup Push Button
2
Arc Control Push Button
3
Adjust Knob
4
Wire Feed Speed/Amps Display Push
Button
Enter the Set Value mode by pressing the
Setup and Arc Control push buttons at the
same time. When in the Set Value mode the
display windows briefly shows SET VALU and
the blinking LEDs under the display windows
indicate whether Volts, Arc Adjust, or Wire
Speed can be changed turning the Adjust
knob.
Depending on the defined weld process,
either volts (MIG) or arc adjust [pulse,
Accu-pulse, or RMD (optional)] can be
changed in the top display. Wire speed can be
changed in the bottom display. Press the Wire
Feed Speed/Amps push button to toggle
between selecting information in the top
display or bottom display. The LED under the
active display will blink to indicate the value
that can be changed.
Rotate the Adjust knob to change values.
Exit the Set Value mode by pressing the Setup
and Arc Control push buttons at the same time
or turning power source off and then back on
again.
Set Value mode overrides robot wire feed
speed, voltage, and trim commands. To weld
in this mode, the robot only needs to provide
a contactor signal, and voltage and wire feed
speed will be ignored.
OM-240 146 Page 31
7-2. Diagnostics
The following error messages are shown on the
upper and lower displays to indicate specific errors.
Explanations are in the text below:
ERR
ERR
ERR
ERR
ERR
ERR
TACH
MOTR
WFS
STRT
STOP
FLOW
Indicates a
tachometer error.
Indicates a motor
error.
Indicates a wire
feed speed error.
Indicates an arc
start error.
Indicates an arc
stop error.
ERR
ERR
ERR
ERR
ERR
ERR
COOL
GND
STUK
TEMP
LINE
ARC
Indicates a coolant
flow error.
Indicates a ground
current error.
ERR TACH
• Tach error for Tach A occurs 2 seconds
after the loss of tachometer feedback. The
motor speed is regulated through the
monitoring of voltage and current. Press
Jog/Purge button to clear error.
• Tach error for Tach B occurs 2 seconds
after the loss of tachometer feedback. The
motor speed is regulated through the
monitoring of voltage and current. Press
Jog/Purge button to clear error.
ERR MOTR
• The motor error indicates that the motor
has been drawing too much current for too
long. To remedy this, reduce the wire feed
speed or the wire feeder torque load/duty
cycle. Press Jog/Purge button to clear error.
ERR WFS
• The wire feed speed error indicates actual
wire feed speed does not match wire feed
speed command. Press Jog/Purge button
to clear error.
ERR STRT
• The start error, when enabled, occurs if the
trigger is held longer than three seconds
without an arc start. The error may be
cleared by releasing the trigger, and
pressing the Jog/Purge button.
OM-240 146 Page 32
Indicates a wire
stuck error.
Indicates a
temperature error.
Indicates a line
error.
Indicates a gas
flow error.
Indicates an arc
error.
ERR STOP
ERR STUK
• The stop error occurs as result of
obstructions in the wire feed system or a
faulty wire drive system. Check wire feed
and wire drive systems. Press Jog/Purge
button to clear error.
• The stuck error occurs if the welding wire
sticks to the workpiece at the end of a weld.
May be caused by poor weld conditions.
The error may be cleared by cutting wire
from workpiece, and pressing the Jog/
Purge button.
ERR FLOW
ERR TEMP
• The flow error indicates no gas flow to the
gun. The error may be reset by
reestablishing gas flow to the gun, and then
pressing the Jog/Purge button.
ERR COOL
• The cool error indicates no coolant flow in
water flow switch option. The error may be
reset by reestablishing coolant flow to the
gun, and then pressing the Jog/Purge
button.
ERR GND
• The ground current error occurs if weld
current is detected in the earth ground
connection. May be caused by a conductor
making contact with unit chassis. Check
and repair feeder weld connections. Turn
power off and back on to clear error.
• The temperature error indicates welding
power source has overheated and
shutdown. The error may be cleared by
allowing unit to cool down, and pressing the
Jog/Purge button. If problem persists,
check fan motors and thermistors for proper
operation. If unit is not overheated, check input line voltage. If input line voltage is okay,
contact nearest factory authorized Service
Agent.
ERR LINE
• The line error indicates input power is
outside of unit operating range. Check and
correct input power. Press Jog/Purge
button to clear error.
ERR ARC
• The arc error indicates an arc outage
occurred possibly from a wire feeder error
or power source error. Check wire feeder
and power source. Press Jog/Purge button
to clear error.
7-2.
Diagnostics (Continued)
WELD
MOTR
PLS
LOW
ROBT
E
WAIT
COM
WAIT
WFS
MEM
STOP
Indicates a weld
cycle wait error.
Indicates a motor
communication error.
Indicates a UIM
Indicates a low WFS
communication error. command error.
DEMO
OVER
UNIT
OVER
DONE
AVG
COMM
CRNT
Indicates RMD/Accuspeed demo is
expired.
Indicates an over
average current error.
Indicates a CRC
PCM bus error.
Indicates a CRC
robot memory error.
Indicates an
emergency stop error.
Indicates an
overcurrent error.
WELD WAIT
ROBT MEM
UNIT COMM
• The weld wait error indicates unit was not
ready for a weld sequence. Press Jog/
Purge button to clear error.
• The robot memory error indicates robot
lost memory data. Press Jog/Purge button
to clear error.
• The unit communication error indicates
the data bus on the PCM board is not
functioning properly. Press Jog/Purge
button to clear error.
MOTR COM
• The motor communication error indicates motor board lost data communications. Press Jog/Purge button to clear error.
If condition persists, contact nearest factory
authorized service agent.
PLS WAIT
• The uim communication error indicates
user
interface
board
lost
data
communications. Press Jog/Purge button
to clear error. If condition persists, contact
nearest factory authorized service agent.
LOW WFS
• The low wire feed speed error indicates
actual wire feed speed is lower than wire
feed speed command. Check for
obstructions in the wire feed system or a
faulty wire drive system. Press Jog/Purge
button to clear error.
E STOP
• The emergency stop error occurs if the
user presses an emergency stop button.
Reset the emergency stop button and press
Jog/Purge button to clear error. Only applies
to units equipped with E stop option.
DEMO DONE
• The DEMO done message indicates the
RMD and Accuspeed demos are completed. Pressing Jog/Purge button will change
the screen to CYCL PWR on the display.
Turn unit power off and back on again. RMD
and Accuspeed share the same demo timer.
If the time expires for one demo process,
both demo processes are deactivated.
OVER AVG
• The over average error indicates that
current is outside the average range for the
set program parameters. Check and correct
program parameters. Press Jog/Purge
button to clear error.
OVER CRNT
• The over current error indicates welding
power source primary current of the inverter
is too high. Turn welding power source off
and disconnect unit for servicing.
Attempting to reset the display to
continue welding may further damage
internal components. A complete
prepower check of the unit is needed
including resistance measurements of R1
and R8 resistors on welding power source
Interconnect board. Resistors should
measure 30K ohms. Visually inspect
electrolytic capacitors C1 and C2 for any
possible damage. In the event of an over
voltage condition, R1 and R8 could open
potentially causing an imbalance in the
power circuit. This condition would create
excessive current in the inverter primary
transformer and result in the OVER CRNT
error.
OM-240 146 Page 33
7-2.
Diagnostics (Continued)
REL
TRIG
ERR
TRIG
STUK
UNKN
Indicates a contactor Indicates a trigger
on error.
closed error.
REL TRIG
• The release trigger error indicates the
user held the gun trigger after an E stop was
reset causing the contactor to remain on.
Press Jog/Purge button to clear error.
TRIG STUK
• The trigger stuck error indicates the user
held the gun trigger during power up.
Release trigger and turn power off and back
on.
OM-240 146 Page 34
Indicates an
unknown error.
ERR UNKN
• The unknown error indicates an error was
sent from the PCM board to the UIM, but
error condition is unknown. Make sure
welding power source is isolated from the
welding fixture. Press Jog/Purge button to
clear error.
7-3. Removing Cover and Measuring Input Capacitor Voltage
Tools Needed:
!
Turn Off welding power
source, and disconnect
input power.
!
Significant DC voltage can
remain on capacitors after
unit is Off. Always check the
voltage as shown to be sure
the input capacitors have
discharged before working
on unit.
1
2
5/16 in.
Turn Off welding power source, and
disconnect input power.
Remove cover
1
Power Interconnect Board
PC2
2
Voltmeter
Measure the DC voltage across the
+ bus terminal and − bus terminal on
PC2 as shown until voltage drops to
near 0 (zero) volts. Measure input
capacitor voltage on all three
inverter
assemblies
before
proceeding.
+ lead to left bus terminal, − lead to right
bus terminal
1
2
. If the capacitor voltage does
not drop to near zero after
several minutes, use a bleeder
resistor of between 25 and
1000 ohms, at least 5 watts,
#16 AWG 1000 volts DC
insulating rating wire
to
discharge the capacitor(s).
3
+ lead to left bus terminal, − lead to right
bus terminal
Typical Bleeder Resistor
An example of a typical bleeder
resistor is shown on this page.
Proceed with job inside unit.
Reinstall cover when finished.
1
2
+ lead to left bus terminal, − lead to right
bus terminal
3
Typical Bleeder
Resistor
25 to 1000 ohm,
5 watt resistor
#16 AWG 1000 volts DC
insulation rating, approx
3 in. (76 mm) leads
802 301-B / 248 978-A
OM-240 146 Page 35
7-4. Process Control Module PC4 Diagnostic LEDs
1
Process Control Module PC4
Diagnostic LEDs are visible inside unit,
located on PC4 mounted on the top tray.
1
Refer to Section 7-5 for information on
diagnostic LEDs.
LED1
Reinstall cover after checking diagnostic
LEDs.
LED2
LED3
LED4
216 956-A / 248 978-A
7-5. Diagnostic LEDs On Process Control Module PC4
LED
Status
1
On
Indicates −25 volts DC is present on process control module PC4
Off
Indicates −25 volts DC is not present on process control module PC4
On
Indicates +25 volts DC is present on process control module PC4
Off
Indicates +25 volts DC is not present on process control module PC4
On
See Network Status Table in Section 7-10
Off
See Network Status Table in Section 7-10
2
3,4
OM-240 146 Page 36
Diagnosis
7-6. Wire Feed Module PC6 Diagnostic LEDs And Dip Switch Settings
1
2
Wire Feed Module PC6
Diagnostic LEDs are visible inside
unit, located on PC6 mounted on
the top tray assembly.
Refer to Section 7-7 for information
on diagnostic LEDs.
Reinstall top cover after checking
diagnostic LEDs.
1
LED1
LED2
2
Dip Switch S1
Dip switches are used to identify
each circuit board on the internal
network. Dip switch settings are
different for each circuit board. For
proper operation, do not change dip
settings from those shown.
LED3
LED4
217 333-B / 805 334-A
7-7. Diagnostic LEDs On Wire Feed Module PC6
LED
Status
1
On
Indicates +15 volts DC is present on wire feed module PC6
Off
Indicates +15 volts DC is not present on wire feed module PC6
On
Indicates +5 volts DC is present on wire feed module PC6
Off
Indicates +5 volts DC is not present on wire feed module PC6
On
See Network Status Table in Section 7-10
Off
See Network Status Table in Section 7-10
2
3,4
Diagnosis
OM-240 146 Page 37
7-8. User Interface Module PC7 Diagnostic LEDs
LED1
2
LED2
3
1
218 559-A / 805 334-A
1 User Interface Module PC7
Diagnostic LEDs are visible inside unit,
located on PC7 mounted behind the front
panel.
Refer to Section 7-9 for information on
diagnostic LEDs.
Reinstall cover after checking diagnostic
LEDs.
2
Dip Switch S1
3
Dip Switch S2
7-9. Diagnostic LEDs On User Interface Module PC7
LED
Status
1, 2
On
See Network Status Table in Section 7-10
Off
See Network Status Table in Section 7-10
OM-240 146 Page 38
Diagnosis
Dip switches are used to identify each
circuit board on the internal network. Dip
switch settings are different for each circuit
board. For proper operation, do not change
dip settings from those shown.
7-10. Network And Module Status LEDs
A. Network Status LEDs
The following are network status LEDs:
LED1 on the UIM circuit board
LED4 on the WFM and PCM circuit boards
LED30 on the AIM circuit board.
Status
Off
Green
Flashing Green
Red
Diagnosis
The circuit board is not on-line with the network or there is no power applied to the circuit board.
The circuit board is operating normally and the on-line connection is made with the network.
The circuit board is wait for an on-line connection to be made with the network.
The circuit board has encountered a communication link failure with the network. Check DeviceNet cable connections. Verify
dip switch positions according to Sections 1-2 and 1-3. Replace circuit board if necessary.
B. Module Status LEDs
The following are module status LEDs:
LED2 on the UIM circuit board
LED3 on the WFM and PCM circuit boards
LED31 on the AIM circuit board.
Status
Off
Green
Flashing Red
Red
Diagnosis
There is no power applied to the circuit board or the board software is not executing its functions.
The circuit board is operating normally.
The circuit board has encountered a recoverable fault. Wait or cycle power to clear fault.
The circuit board has encountered an unrecoverable fault.
OM-240 146 Page 39
7-11. Troubleshooting
Trouble
No weld output; completely inoperative
Remedy
Place line disconnect in On position (see Section 3-17).
Check and replace line fuse(s), if necessary, or reset circuit breaker (see Section 3-17).
Check for proper input power connections (see Section 3-17).
Erratic or improper weld output with no Use proper size and type of weld cable (see Section 3-11).
errors displayed.
Check that proper program for wire size, process, and shielding gas is loaded.
Clean and tighten all weld connections.
No 115 volts AC at the duplex receptacle. Reset supplementary protector CB1 (see Section 3-9).
Wire does not feed.
Check supplementary protector CB2 and reset if necessary (see Section 3-9).
Check motor control cable connections.
Wire feeds erratically.
Readjust hub tension.
Readjust drive roll pressure.
Clean or replace dirty or worn drive rolls.
Remove weld spatter around the nozzle opening.
Replace contact tip or liner. See gun Owner’s Manual.
Check motor control cable connections.
Wire feeds as soon as power is supplied. Check robot contactor status.
Wire stubbing on low end using a Increase output setting of the power source.
constant current power source.
Check voltage sense lead connection, clean and tighten if necessary.
Gas does not flow or does not stop flow- Check gas valve and flow meter.
ing; wire feeds.
Wire burns back to gun contact tip when Check to be sure that volt sense lead is connected to the work.
using electrode negative (straight
polarity) process.
OM-240 146 Page 40
Notes
OM-240 146 Page 41
SECTION 8 − ELECTRICAL DIAGRAMS
Figure 8-1. Circuit Diagram For Welding Power Source (Part 1 Of 2)
OM-240 146 Page 42
237 935-D (Part 1 Of 2)
OM-240 146 Page 43
Figure 8-2. Circuit Diagram For Welding Power Source (Part 2 Of 2)
OM-240 146 Page 44
237 935-D (Part 2 Of 2)
OM-240 146 Page 45
Ref. 219 267-B
Figure 8-3. Circuit Diagram For Peripheral/Motor Interface
OM-240 146 Page 46
Notes
OM-240 146 Page 47
SECTION 9 − PARTS LIST
. Hardware is
common and
not available unless listed.
1
2
3
4 Fig.9−3
5 Fig.9−2
6
5
7 Fig.9−4
8
6
17
19
5
18
8
10
16 Fig. 9−5
13
14
15
15
12
11
18
9
805 330-B
Figure 9-1. Main Assembly
OM-240 146 Page 48
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 9-1. Main Assembly
. . . 1 . . . . . T2 . . . . . . . 212543
. . . 2 . . . . . . . . . . . . . . . . 210492
. . . 3 . . . . . . . . . . . . . . . . 210481
. . . 4 . . . . . . . . . . . . . . . . . Fig 9-3
. . . 5 . IM1,IM2,IM3 . . . 214597
. . . . . . . . . . . . . . . . . . . . . . 222958
. . . 6 . . . . . . . . . . . . . . . . 198961
. . . 7 . . . . . . . . . . . . . . . . . Fig 9-4
. . . 8 . . . . . . . . . . . . . . . . 227791
. . . 9 . . . . . . . . . . . . . . . . 210482
. . . 10 . . . . . W1 . . . . . . . 160793
. . . 11 . . . . . . . . . . . . . . . . 213386
. . . 12 . . . . HD2 . . . . . . 182918
. . . 13 . . . . . . . . . . . . . . . . 198951
. . . 14 . . . . . . . . . . . . . . . . 148025
. . . 15 . . . . . . . . . . . . . . . . 218365
. . . 16 . . . . . . . . . . . . . . . . . Fig 9-5
. . . . . . . . . . . . . . . . . . . . . . 227855
. . . 17 . . . . . . . . . . . . . . . . 010467
. . . 18 . . . . . . . . . . . . . . . . 225840
. . . 19 . . . . . . . . . . . . . . . . 010916
. . . Xfmr, Control Toroidal 665 VAC Pri 1900 VA 60 Hz . . . . . . . . . . . . . . . . .
. . . Cover, Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Plate, Mtg Toroid Xfmr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Top Tray Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Windtunnel, LH w/Components (Fig 9-2) . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Windtunnel, RH w/Components (Fig 9-2) . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Panel, Module Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Rear Panel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Panel, Side W/Insulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Contactor, DEF PRP 60A 3P 24VAC Coil W/Boxlug . . . . . . . . . . . . . . . .
. . . Assembly, Filter (Primary) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Transducer, Current 400A Module Supply V +/− 15V . . . . . . . . . . . . . . .
. . . Block, Terminal 3 Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Lug, Univ W/SCR 600V 2/0−6 Wire .266 Stud . . . . . . . . . . . . . . . . . . . . .
. . . Filter Assy, Secondary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Front Panel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Kit, Connectors W/Washer For Power Cables (Includes) . . . . . . . . . . . .
. . . . Connector, Clamp Cable 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Washer, Reducer 1.25 in − 0.75 in . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Connector, Clamp Cable 0.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
3
3
2
1
2
1
1
1
1
1
1
2
1
1
1
2
1
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
14
. Hardware is
common and
not available unless listed.
15
2
1
3
4
5
13
6
12
7
11
8
9
33
10
6
34
35
7
17
16
18
19
32
31
20 21
30
29
23
24
25
23
27
13
36
28
26
22
23
38
37
802 955-A
Figure 9-2. Windtunnel Assembly LH And RH
OM-240 146 Page 49
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 9-2. Windtunnel Assembly LH And RH (Fig 9-1 Item 6)
... 1 ................
... 2 ................
. . . 3 . . . . . L1 . . . . . . .
... 4 ................
. . . 5 . . . R3, C4 . . . . .
... 6 ................
. . . 7 . . . D1, D2 . . . . .
... 8 ................
... 9 ................
. . . 10 . . . . . T1 . . . . . . .
. . . 11 . . . . . Z1 . . . . . . .
. . . 12 . . . . . . . . . . . . . . . .
. . . 13 . . . . . . . . . . . . . . . .
. . . 14 . . . . . . . . . . . . . . . .
. . . 15 . . . . . . . . . . . . . . . .
. . . 16 . . . . . . . . . . . . . . . .
. . . 17 . . . . . . . . . . . . . . . .
. . . 18 . . . . . . . . . . . . . . . .
. . . 19 . . . . . . . . . . . . . . . .
......................
......................
. . . . . . . . . . CT1 . . . . . .
. . . 20 . . . . . . . . . . . . . . . .
. . . 21 . . . C1, C2 . . . . .
. . . 22 . . . . . . . . . . . . . . . .
. . . 23 . . . . . . . . . . . . . . . .
. . . 24 . . RT1, RT2 . . . .
. . . 25 . . . . PC2 . . . . . .
. . . 26 . . . . . C3 . . . . . . .
. . . 27 . . . . . . . . . . . . . . . .
. . . 28 . . . . HD1 . . . . . .
......................
. . . 29 . . . R1, R2 . . . . .
......................
. . . 30 . . . . . . . . . . . . . . . .
. . . 31 . . . . . . . . . . . . . . . .
. . . 32 . . . . . . . . . . . . . . . .
. . . 33 . . . . . . . . . . . . . . . .
. . . 34 . . . . . L2 . . . . . . .
. . . 35 . . . . . . . . . . . . . . . .
......................
......................
. . . 36 . . . . PC1 . . . . . .
. . . 37 . . . . . . . . . . . . . . . .
. . . 38 . . . . . . . . . . . . . . . .
214597
196351
213940
214519
233052
199840
201531
196347
196349
203408
220496
170647
179276
196355
010546
222958
196332
030170
196259
115092
115091
196231
201695
226081
210507
217625
214015
237370
196143
196378
182918
196384
196343
196840
109056
196514
196512
196330
196345
196588
196365
199136
239612
204846
083147
. . . Windtunnel, LH w/Components (including). . . . . . . . . . . . . . . . . . . . . . . .
. . . . Windtunnel, LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Inductor, Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Insulator, Heat Sink Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Resistor/Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bus Bar, Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Kit, Diode Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Heat Sink, Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Spacer, Windtunnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Xfmr, HF Litz/Litz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Output Inductor Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bushing, Snap−in Nyl 1.312 Id X 1.500 Mtg Hole . . . . . . . . . . . . . . . .
. . . . Bushing, Snap−in Nyl 1.000 Id X 1.375 Mtg Hole Cent . . . . . . . . . . . .
. . . . Insulator, Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bushing, Snap−in Nyl .375 Id X .500 Mtg Hole . . . . . . . . . . . . . . . . . . .
. . . Windtunnel, RH w/Components (including) . . . . . . . . . . . . . . . . . . . . . . .
. . . . Windtunnel, RH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bushing, Snap−in Nyl .750 Id X 1.000 Mtg Hole Cent . . . . . . . . . . . . .
. . . . Plugs, w/Leads & Current Xfmr (including) . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . Housing, Plug & Skts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . Housing, Plug & Skts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . Xfmr, Current Sensing 200/1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Clamp, Capacitor (Bottom) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Capacitor,Elctlt 2400 Uf 500 VDC Can 2.50 Dia . . . . . . . . . . . . . . . .
. . . . Clamp, Capacitor (Top) Machined . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Kit, Input/Pre−regulator And Inverter Module . . . . . . . . . . . . . . . . . . . .
. . . . Thermistor, NTC 30K Ohm @ 25 Deg C 7&18in Lead . . . . . . . . . . . .
. . . . Circuit Card Assy, Power Interconnect . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Capacitor, Polyp Met Film 16. Uf 400 VAC 10% . . . . . . . . . . . . . . . . . .
. . . . Bracket, Mtg Current Xfmr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Transducer, Current 400A Module Supply V +/− 15v . . . . . . . . . . . . . .
. . . . Cable, Transducer 20in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Resistors, W/Leads & Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Insulator, Resistors/Interface Board . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Core, Ferrite E 2.164 Lg X 1.094 High X .826 Wide . . . . . . . . . . . . . .
. . . . Gasket, Inductor Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bracket, Inductor Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Heat Sink, Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Coil, Inductor (Pre−regulator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Baffle, Foam Rubber (Lower) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Plugs, w/Leads (Fan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Plugs, w/Leads (PC2 To PC1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Circuit Card Assy, Control (Inverter 300A) . . . . . . . . . . . . . . . . . . . . . . . .
. . . Insulator, Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Grommet, Scr No 8/10 Panel Hole .312 Sq .500 High . . . . . . . . . . . . . .
1
1
1
1
1
2
2
1
3
1
1
2
4
6
1
1
1
2
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-240 146 Page 50
1
. Hardware is
common and
not available unless listed.
2
3
4
5
11
6
10
7
9
8
802 916-B
Figure 9-3. Top Tray Assembly
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 9-3. Top Tray Assembly (Fig 9-1 Item 4)
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
5
6
7
8
9
10
11
. . . . PC12 . . . . . .
. . . . PC3 . . . . . .
................
................
................
. . . . PC4 . . . . . .
................
................
................
................
. . . . PC6 . . . . . .
239623
239598
210490
134201
083147
221277
170647
210491
223439
198122
221280
. . . Circuit Card Assy, E−stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Circuit Card Assy, Aux Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Panel, Mtg Circuit Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Stand−Off, PC Card .312/.375/Post&Lock .43 . . . . . . . . . . . . . . . . . . . . .
. . . Grommet, SCR No 8/10 Panel Hole .312 Sq .500 High . . . . . . . . . . . . .
. . . Process Control Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Bushing, Snap−in Nyl 1.312 Id X 1.500 Mtg Hole . . . . . . . . . . . . . . . . . .
. . . Panel, Mtg Components Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Insulator, Circuit Card (Aux Power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Stand−Off Support, PC Card .250 w/Post&Lock .500 . . . . . . . . . . . . . . .
. . . Wire Feed Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
4
4
1
1
1
1
1
1
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-240 146 Page 51
4
1
2
3
. Hardware is
common and
not available unless listed.
16
14
5
15
6
17
14
12
7
8
13
9
10
11
805 331-B
Figure 9-4. Rear Panel Assembly
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 9-4. Rear Panel Assembly
. . . 1 . . . . . . . . . . . . . . . . 217297 . . . Cover, Receptacle Weatherproof Duplex Rcpt . . . . . . . . . . . . . . . . . . . . .
. . . 2 . . . . . . . . . . . . . . . . 210471 . . . Panel, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 3 . . . . . . . . . . . . . . . . 210358 . . . Bolt, eye shld thd stem .500−13 X 1.500 . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 4 . . . . . . . . . . . . . . . . 210505 . . . Nameplate, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 5 . . . . . . . . . . . . . . . . 224012 . . . Plate, Rotation Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 6 . . . . . . . . . . . . . . . . 198956 . . . Receptacle, Devicenet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 7 . . . . . . . . . . . . . . . . 210483 . . . Bracket, lift eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 8 . . . . CB1 . . . . . . 083432 . . . Supplementary Protector, Man Reset 1P 10A 250VAC Frict . . . . . . . . .
. . . 9 . . . . CB2 . . . . . . 093995 . . . Supplementary Protector, Man Reset 1P 15A 250VAC Frict . . . . . . . . .
. . . 10 . . . . PC11 . . . . . . 239631 . . . Circuit Card Assy, Motor Filter Hf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 11 . . . . . . . . . . . . . . . ♦237094 . . . Circuit Card Assy, Tandem Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 12 . . . . . . . . . . . . . . . . 216596 . . . Strap, Grounding 4.50 in long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 13 . . . . RC2 . . . . . . 604176 . . . Receptacle, w/Leads (115V Duplex) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 14 . . . . . . . . . . . . . . . . 225955 . . . Plate, Mounting E-Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-Stop Connector Factory Installed Option For Axcess (includes) . . . .
. . . 15 . . . . PC12 . . . . . ♦227901 . . . . E-Stop Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 16 . . . . . . . . . . . . . . . ♦228694 . . . . Jumper,Connector W/Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 17 . . . . PC22 . . . . . . 243799 . . . Circuit Card Assy,W/Touch Sense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
♦OPTIONAL
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-240 146 Page 52
. Hardware is
common and
not available unless listed.
2
1
23
4
3
24
22
21
6
7
5
20
8
15
14
7
13
9
10
19
11
12
9
16
17
18
18
802 918-C
Figure 9-5. Front Panel Assembly
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 9-5. Front Panel Assembly
...
...
...
...
...
...
...
...
...
1
2
3
4
5
6
7
8
9
. . . . . S1 . . . . . . .
................
................
................
. . . . . FM . . . . . . .
. . . . PC13 . . . . . .
. C6, C7, C8 . . .
................
................
207456
207895
179851
233575
196313
239619
206878
213102
025248
. . . Switch Assy, Rotary 2 Posn 1P 40A 600VAC PNLMTG 90Deg . . . . . .
. . . Insulator,Switch Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Knob, Pointer 1.670 Dia X .250 Id Push On W/Spring . . . . . . . . . . . . . .
. . . Panel, PC Card Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Fan, Muffin 115V 50/60 Hz 3000 Rpm 6.378 Mtg Holes . . . . . . . . . . . . .
. . . Circuit Card Assy,ISO/COMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Capacitor Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Choke, Common Mode w/Leads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Stand−off, Insul .250−20 X 1.250 Lg X .437 Thd . . . . . . . . . . . . . . . . . . .
1
1
1
1
3
1
3
2
3
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-240 146 Page 53
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 9-5. Front Panel Assembly (Continued)
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
................
................
................
. . . . RC5 . . . . . .
................
................
................
................
................
PB1, PB2, PB3 . .
................
................
................
................
................
220815
210864
210866
214664
216966
216965
219843
203862
186621
199443
237836
210865
237836
210358
210483
. . . Bus Bar, Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Bus Bar, Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Terminal, pwr output black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Receptacle, Common Mode Choke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Cover, Connector D-sub 9 pin Male w/Chain . . . . . . . . . . . . . . . . . . . . . .
. . . Cover, Connector D-sub 9 skt Female w/Chain . . . . . . . . . . . . . . . . . . . .
. . . Label, Volt Sense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Box, Louver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Boot, Generic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Switch, Pb Mc No Spst 10A 115VAC w/Blk Cap Panelmt . . . . . . . . . . .
. . . Nameplate, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Terminal, pwr output red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Panel, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Bolt, eye shld thd stem .500−13 X 1.500 . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Bracket, lift eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
2
3
1
1
1
1
1
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-240 146 Page 54
Effective January 1, 2011
(Equipment with a serial number preface of MB or newer)
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions 6. 90 Days — Parts
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to its
* Accessory (Kits)
original retail purchaser that new Miller equipment sold after the
* Canvas Covers
effective date of this limited warranty is free of defects in material
* Induction Heating Coils and Blankets, Cables, and
and workmanship at the time it is shipped by Miller. THIS
Non-Electronic Controls
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
* M-Guns
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
* MIG Guns and Subarc (SAW) Guns
WARRANTIES OF MERCHANTABILITY AND FITNESS.
* Remote Controls and RFCS-RJ45
Within the warranty periods listed below, Miller will repair or replace
* Replacement Parts (No labor)
any warranted parts or components that fail due to such defects in
* Roughneck Guns
material or workmanship. Miller must be notified in writing within
* Spoolmate Spoolguns
thirty (30) days of such defect or failure, at which time Miller will
provide instructions on the warranty claim procedures to be
followed.
Miller shall honor warranty claims on warranted equipment listed
below in the event of such a failure within the warranty time
periods. All warranty time periods start on the delivery date of the
equipment to the original end-user purchaser, and not to exceed
one year after the equipment is shipped to a North American
distributor or eighteen months after the equipment is shipped to an
International distributor.
1.
2.
3.
4.
5.
5 Years Parts — 3 Years Labor
* Original main power rectifiers only to include SCRs,
diodes, and discrete rectifier modules
3 Years — Parts and Labor
* Engine Driven Welding Generators
(NOTE: Engines are warranted separately by the
engine manufacturer.)
* Inverter Power Sources (Unless Otherwise Stated)
* Plasma Arc Cutting Power Sources
* Process Controllers
* Semi-Automatic and Automatic Wire Feeders
* Smith 30 Series Flowgauge and Flowmeter
Regulators (No Labor)
* Transformer/Rectifier Power Sources
* Water Coolant Systems (Integrated)
2 Years — Parts
* Auto-Darkening Helmet Lenses (No Labor)
1 Year — Parts and Labor Unless Specified
* Automatic Motion Devices
* CoolBelt and CoolBand Blower Unit (No Labor)
* External Monitoring Equipment and Sensors
* Field Options
(NOTE: Field options are covered for the remaining
warranty period of the product they are installed in, or
for a minimum of one year — whichever is greater.)
* Flowgauge and Flowmeter Regulators (No Labor)
* RFCS Foot Controls (Except RFCS-RJ45)
* Fume Extractors
* HF Units
* ICE Plasma Cutting Torches (No Labor)
* Induction Heating Power Sources, Coolers, and
Electronic Controls/Recorders
* Load Banks
* Motor Driven Guns (w/exception of Spoolmate
Spoolguns)
* PAPR Blower Unit (No Labor)
* Positioners and Controllers
* Racks
* Running Gear/Trailers
* Spot Welders
* Subarc Wire Drive Assemblies
* Water Coolant Systems (Non-Integrated)
* Weldcraft-Branded TIG Torches (No Labor)
* Wireless Remote Foot/Hand Controls and Receivers
* Work Stations/Weld Tables (No Labor)
6 Months — Parts
* Batteries
* Bernard Guns (No Labor)
* Tregaskiss Guns (No Labor)
Miller’s True Blue® Limited Warranty shall not apply to:
1.
2.
3.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, relays, work
station table tops and welding curtains, or parts that
fail due to normal wear. (Exception: brushes and
relays are covered on all engine-driven products.)
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable
and necessary maintenance, or equipment which has
been used for operation outside of the specifications for
the equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4) payment
of or credit for the purchase price (less reasonable depreciation
based upon actual use) upon return of the goods at customer’s risk
and expense. Miller’s option of repair or replacement will be F.O.B.,
Factory at Appleton, Wisconsin, or F.O.B. at a Miller authorized
service facility as determined by Miller. Therefore no
compensation or reimbursement for transportation costs of any
kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY
OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION, OPERATION OF LAW,
CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO
ANY AND ALL EQUIPMENT FURNISHED BY MILLER IS
EXCLUDED AND DISCLAIMED BY MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein, and
to the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available,
but may vary from province to province.
miller_warr 2011−01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
For International Locations Visit
www.MillerWelds.com
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
ORIGINAL INSTRUCTIONS − PRINTED IN USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
© 2011 Miller Electric Mfg. Co.
2011−01