Miller BIG BLUE AIR PAK User manual

Miller BIG BLUE AIR PAK User manual
OM-4409
206 941X
2008−07−09
Processes
Stick (SMAW) Welding
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
TIG (GTAW) Welding
Air Carbon Arc (CAC-A)
Cutting and Gouging
With Optional Equipment:
Battery Charging
Description
Engine Driven Welding Generator And
Air Compressor
®
Big Blue Air Pak
File: Engine Drive
Visit our website at
www.MillerWelds.com
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001:2000 Quality Warranty and service information for your
System Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual specification sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 4/05
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Engine Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. Compressed Air Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-7. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-8. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Signification des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Dangers existant en relation avec le moteur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4. Dangers liés à l’air comprimé . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance . . . . . .
2-6. Proposition californienne 65 Avertissements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8. Information EMF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Weld, Power, And Engine Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Air Compressor Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Sound Level Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Dimensions, Weights, And Operating Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Stick And MIG Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. TIG Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. Fuel Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9. Generator AC Power Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10. Optional 3-Phase Generator Power Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-11. Air Compressor Output Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-12. Optional Battery Charging Output Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Installing Welding Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Mounting Welding Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Rating Label Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Installing Optional Spark Arrestor Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6. Activating The Dry Charge Battery (If Applicable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Connecting The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8. Using The Optional Battery Disconnect Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-9. Engine/Compressor Prestart Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-10. Connecting To Weld Output Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-11. Selecting Weld Cable Sizes* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-12. Connecting To Remote 14 Receptacle RC14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-13. Connecting To The Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − OPERATING THE WELDING GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Controls (See Section 6-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Description Of Controls (See Section 6-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. Process/Contactor Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4. Using Remote Voltage/Amperage Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-5. Fuel/Hour Gauge Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
3
3
4
5
5
5
6
6
6
8
9
9
11
11
11
12
12
13
13
13
13
14
15
16
17
17
18
19
20
20
21
21
22
23
24
25
25
26
27
28
29
30
31
32
32
33
34
35
36
TABLE OF CONTENTS
SECTION 7 − OPERATING AUXILIARY EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Domestic Auxiliary Power Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Connecting To Optional AC Power Plant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3. Export Auxiliary Power Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − OPERATING OPTIONAL BATTERY CHARGER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1. Battery Charge Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2. Determining Battery Charging Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-3. Battery Charge Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-4. Battery Charging Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-5. Jump Starting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − ENGINE/GENERATOR MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-1. Engine Maintenance Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-2. Routine Engine/Generator Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-3. Checking Generator Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-4. Servicing Engine Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-5. Inspecting/Cleaning Optional Spark Arrestor Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-6. Adjusting Engine Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-7. Servicing Engine Fuel And Lubrication Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-8. Engine/Generator Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10 − AIR COMPRESSOR MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1. Air Compressor Maintenance Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-2. Routine Air Compressor Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-3. Servicing Compressor Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-4. Compressor Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-5. Servicing Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-6. Adjusting Compressor Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 11 − TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-1. Troubleshooting Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 12 − CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 13 − AIR COMPRESSOR DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 14 − RUN-IN PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-1. Wetstacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-2. Run-In Procedure Using Load Bank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-3. Run-In Procedure Using Resistance Grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 15 − AIR COMPRESSOR TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15-1. Flow Of Free Air (CFM) Through Orifices Of Various Diameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15-2. Approximate Air Consumption (Cubic Feet) To Operate Pneumatic Equipment At 70-90 P.S.I.G. . . .
SECTION 16 − GENERATOR POWER GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 17 − SELECTING AND PREPARING A TUNGSTEN FOR DC OR AC WELDING . . . . . . . . . . . . .
17-1. Selecting Tungsten Electrode (Wear Clean gloves To Prevent Contamination Of Tungsten) . . . . . . . .
17-2. Preparing Tungsten Electrode For Welding With Phase Control Machines . . . . . . . . . . . . . . . . . . . . . .
SECTION 18 − GUIDELINES FOR TIG WELDING (GTAW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18-1. Positioning The Torch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18-2. Torch Movement During Welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18-3. Positioning Torch Tungsten For Various Weld Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 19 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY
37
37
38
39
40
40
40
41
42
43
44
44
45
46
47
48
49
50
51
52
52
53
54
55
56
57
58
58
62
64
65
65
66
67
68
68
69
70
77
77
77
78
78
79
80
82
SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING
rom_2007−04
Protect yourself and others from injury — read and follow these precautions.
1-1. Symbol Usage
DANGER! − Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in the text.
NOTICE − Indicates statements not related to personal injury.
Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the
hazards.
1-2. Arc Welding Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information
found in the Safety Standards listed in Section 1-7. Read and
follow all Safety Standards.
Only qualified persons should install, operate, maintain, and
repair this unit.
During operation, keep everybody, especially children, away.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks or
severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also live when power is
on. In semiautomatic or automatic wire welding, the wire, wire reel,
drive roll housing, and all metal parts touching the welding wire are
electrically live. Incorrectly installed or improperly grounded equipment is a hazard.
Do not touch live electrical parts.
Wear dry, hole-free insulating gloves and body protection.
Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
Use AC output ONLY if required for the welding process.
If AC output is required, use remote output control if present on
unit.
Additional safety precautions are required when any of the following electrically hazardous conditions are present: in damp
locations or while wearing wet clothing; on metal structures such
as floors, gratings, or scaffolds; when in cramped positions such
as sitting, kneeling, or lying; or when there is a high risk of unavoidable or accidental contact with the workpiece or ground. For these
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone!
Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
Always verify the supply ground — check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
When making input connections, attach proper grounding conductor first − double-check connections.
Keep cords dry, free of oil and grease, and protected from hot metal
and sparks.
Frequently inspect input power cord for damage or bare wiring —
replace cord immediately if damaged — bare wiring can kill.
Turn off all equipment when not in use.
Do not use worn, damaged, undersized, or poorly spliced cables.
Do not drape cables over your body.
If earth grounding of the workpiece is required, ground it directly
with a separate cable.
Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
Do not touch electrode holders connected to two welding machines at the same time since double open-circuit voltage will be
present.
Wear a safety harness if working above floor level.
Keep all panels and covers securely in place.
Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
Do not connect more than one electrode or work cable to any
single weld output terminal.
SIGNIFICANT DC VOLTAGE exists in inverters after stopping engine.
Stop engine on inverter and discharge input capacitors according
to instructions in Maintenance Section before touching any parts.
HOT PARTS can cause severe burns.
Do not touch hot parts bare handed.
Allow cooling period before working on equipment.
To handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.
FLYING METAL or DIRT can injure eyes.
Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
Wear approved safety glasses with side shields even under your
welding helmet.
OM-4409 Page 1
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing these
fumes and gases can be hazardous to your health.
Keep your head out of the fumes. Do not breathe the fumes.
If inside, ventilate the area and/or use local forced ventilation at the
arc to remove welding fumes and gases.
If ventilation is poor, wear an approved air-supplied respirator.
Read and understand the Material Safety Data Sheets (MSDSs)
and the manufacturer’s instructions for metals, consumables,
coatings, cleaners, and degreasers.
Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements
can give off toxic fumes if welded.
Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
Do not weld where the atmosphere may contain flammable dust,
gas, or liquid vapors (such as gasoline).
Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock, sparks, and fire hazards.
Do not use welder to thaw frozen pipes.
Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
After completion of work, inspect area to ensure it is free of sparks,
glowing embers, and flames.
Use only correct fuses or circuit breakers. Do not oversize or bypass them.
Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
for hot work and have a fire watcher and extinguisher nearby.
NOISE can damage hearing.
BUILDUP OF GAS can injure or kill.
Noise from some processes or equipment can damage hearing.
Shut off shielding gas supply when not in use.
Always ventilate confined spaces or use approved air-supplied respirator.
Wear approved ear protection if noise level is
high.
MAGNETIC FIELDS can affect Implanted
Medical Devices.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays that
can burn eyes and skin. Sparks fly off from the weld.
Wear an approved welding helmet fitted with a proper shade of filter
lenses to protect your face and eyes from arc rays and sparks
when welding or watching (see ANSI Z49.1 and Z87.1 listed in
Safety Standards).
Wear approved safety glasses with side shields under your
helmet.
Use protective screens or barriers to protect others from flash,
glare, and sparks; warn others not to watch the arc.
Wear protective clothing made from durable, flame-resistant material (leather, heavy cotton, or wool) and foot protection.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks, drums,
or pipes, can cause them to blow up. Sparks can fly off
from the welding arc. The flying sparks, hot workpiece,
and hot equipment can cause fires and burns. Accidental contact of
electrode to metal objects can cause sparks, explosion, overheating,
or fire. Check and be sure the area is safe before doing any welding.
Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
Do not weld where flying sparks can strike flammable material.
Protect yourself and others from flying sparks and hot metal.
Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
Watch for fire, and keep a fire extinguisher nearby.
Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
OM-4409 Page 2
Wearers of Pacemakers and other Implanted
Medical Devices should keep away.
Implanted Medical Device wearers should consult their doctor
and the device manufacturer before going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating
operations.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode. Since gas
cylinders are normally part of the welding process, be
sure to treat them carefully.
Protect compressed gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open flames, sparks, and arcs.
Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
Keep cylinders away from any welding or other electrical circuits.
Never drape a welding torch over a gas cylinder.
Never allow a welding electrode to touch any cylinder.
Never weld on a pressurized cylinder — explosion will result.
Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and
associated parts in good condition.
Turn face away from valve outlet when opening cylinder valve.
Keep protective cap in place over valve except when cylinder is in
use or connected for use.
Use the right equipment, correct procedures, and sufficient number of persons to lift and move cylinders.
Read and follow instructions on compressed gas cylinders,
associated equipment, and Compressed Gas Association (CGA)
publication P-1 listed in Safety Standards.
1-3. Engine Hazards
BATTERY EXPLOSION can BLIND.
Always wear a face shield, rubber gloves, and
protective clothing when working on a battery.
Stop engine before disconnecting or connecting battery cables or servicing battery.
Do not allow tools to cause sparks when working on a battery.
Do not use welder to charge batteries or jump start vehicles.
Observe correct polarity (+ and −) on batteries.
Disconnect negative (−) cable first and connect it last.
FUEL can cause fire or explosion.
Stop engine and let it cool off before checking or
adding fuel.
Do not add fuel while smoking or if unit is near
any sparks or open flames.
Do not overfill tank — allow room for fuel to expand.
Do not spill fuel. If fuel is spilled, clean up before starting engine.
Dispose of rags in a fireproof container.
Always keep nozzle in contact with tank when fueling.
MOVING PARTS can cause injury.
Keep away from fans, belts, and rotors.
Keep all doors, panels, covers, and guards
closed and securely in place.
Stop engine before installing or connecting unit.
Have only qualified people remove doors, panels, covers, or
guards for maintenance and troubleshooting as necessary.
To prevent accidental starting during servicing, disconnect
negative (−) battery cable from battery.
Keep hands, hair, loose clothing, and tools away from moving
parts.
Reinstall doors, panels, covers, or guards when servicing is
finished and before starting engine.
Before working on generator, remove spark plugs or injectors to
keep engine from kicking back or starting.
Block flywheel so that it will not turn while working on generator
components.
STEAM AND HOT COOLANT can burn.
If possible, check coolant level when engine is
cold to avoid scalding.
Always check coolant level at overflow tank, if
present on unit, instead of radiator (unless told
otherwise in maintenance section or engine
manual).
If the engine is warm, checking is needed, and there is no overflow tank, follow the next two statements.
Wear safety glasses and gloves and put a rag over radiator cap.
Turn cap slightly and let pressure escape slowly before
completely removing cap.
Using a generator indoors CAN KILL
YOU IN MINUTES.
Generator exhaust contains carbon monoxide.
This is a poison you cannot see or smell.
NEVER use inside a home or garage, EVEN IF
doors and windows are open.
Only use OUTSIDE and far away from windows, doors, and
vents.
BATTERY ACID can BURN SKIN and EYES.
Do not tip battery.
Replace damaged battery.
Flush eyes and skin immediately with water.
ENGINE HEAT can cause fire.
Do not locate unit on, over, or near combustible
surfaces or flammables.
Keep exhaust and exhaust pipes way from
flammables.
HOT PARTS can cause severe burns.
Do not touch hot parts bare handed.
Allow cooling period before working on equipment.
To handle hot parts, use proper tools and/or
wear heavy, insulated welding gloves and
clothing to prevent burns.
EXHAUST SPARKS can cause fire.
Do not let engine exhaust sparks cause fire.
Use approved engine exhaust spark arrestor in
required areas — see applicable codes.
1-4. Compressed Air Hazards
BREATHING COMPRESSED AIR can
cause serious injury or death.
Do not use compressed air for breathing.
Use only for cutting, gouging, and tools.
TRAPPED AIR PRESSURE AND WHIPPING
HOSES can cause injury.
Release air pressure from tools and system before servicing, adding or changing attachments, or opening compressor oil drain or oil fill
cap.
COMPRESSED AIR can cause injury.
Wear approved safety goggles.
Do not direct air stream toward self or others.
OM-4409 Page 3
HOT METAL from air arc cutting and
gouging can cause fire or explosion.
Do not cut or gouge near flammables.
Watch for fire; keep extinguisher nearby.
HOT PARTS can cause burns and injury.
READ INSTRUCTIONS.
Read Owner’s Manual before using or servicing unit.
Stop engine and release air pressure before
servicing.
Use only genuine replacement parts from the
manufacturer.
Do not touch hot compressor or air system
parts.
Let system cool down before touching or servicing.
1-5. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
Do not install or place unit on, over, or near
combustible surfaces.
Do not install unit near flammables.
Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
FALLING UNIT can cause injury.
Use lifting eye to lift unit and properly installed
accessories only, NOT gas cylinders. Do not
exceed maximum lift eye weight rating (see
Specifications).
Lift and support unit only with proper equipment
and correct procedures.
If using lift forks to move unit, be sure forks are long enough to
extend beyond opposite side of unit.
OVERHEATING can damage motors.
Turn off or unplug equipment before starting or
stopping engine.
Do not let low voltage and frequency caused by
low engine speed damage electric motors.
Do not connect 50 or 60 Hertz motors to the 100 Hertz receptacle
where applicable.
FLYING SPARKS can cause injury.
Wear a face shield to protect eyes and face.
Shape tungsten electrode only on grinder with
proper guards in a safe location wearing proper
face, hand, and body protection.
Sparks can cause fires — keep flammables away.
MOVING PARTS can cause injury.
Keep away from moving parts.
Keep away from pinch points such as drive
rolls.
OM-4409 Page 4
WELDING WIRE can cause injury.
Do not press gun trigger until instructed to do
so.
Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
OVERUSE can cause OVERHEATING.
Allow cooling period; follow rated duty cycle.
Reduce current or reduce duty cycle before
starting to weld again.
Do not block or filter airflow to unit.
STATIC (ESD) can damage PC boards.
Put on grounded wrist strap BEFORE handling
boards or parts.
Use proper static-proof bags and boxes to
store, move, or ship PC boards.
TILTING OF TRAILER can cause injury.
Use tongue jack or blocks to support weight.
Properly install welding generator onto trailer
according to instructions supplied with trailer.
READ INSTRUCTIONS.
Read Owner’s Manual before using or servicing unit.
Use only genuine replacement parts from the
manufacturer.
Perform engine and air compressor maintenance and service according to this manual
and the engine/air compressor (if applicable)
manuals.
H.F. RADIATION can cause interference.
High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician
promptly correct any interference problem resulting from the
installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
ARC WELDING can cause interference.
Electromagnetic energy can interfere with
sensitive electronic equipment such as microprocessors, computers, and computer-driven
equipment such as robots.
Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
1-6. California Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
For Gasoline Engines:
Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
For Diesel Engines:
Diesel engine exhaust and some of its constituents are
known to the State of California to cause cancer, birth
defects, and other reproductive harm.
1-7. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1, from Global Engineering Documents (phone:
1-877-413-5184, website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, P.O. Box 9101, Quincy, MA 02269-9101 (phone:
617-770-3000, website: www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 4221 Walney Road, 5th Floor,
Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 5060 Mississauga,
Ontario, Canada L4W 5NS (phone: 800-463-6727 or in Toronto
416-747-4044, website: www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036–8002 (phone:
212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
P.O. Box 9101, Quincy, MA 02269-9101 (phone: 617-770-3000, website: www.nfpa.org.
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 Regional Offices—phone for
Region 5, Chicago, is 312-353-2220, website: www.osha.gov).
1-8. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
To reduce magnetic fields in the workplace, use the following
procedures:
1. Keep cables close together by twisting or taping them, or using a
cable cover.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from
operator as practical.
5. Connect work clamp to workpiece as close to the weld as
possible.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recommended.
OM-4409 Page 5
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT
UTILISATION
rom_2007−04fre
Se protéger, ainsi que toute autre personne travaillant sur les lieux, contre les étincelles et le métal chaud.
2-1. Signification des symboles
DANGER! − Indique une situation dangereuse qui si on
l’évite pas peut donner la mort ou des blessures graves.
Les dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
Indique une situation dangereuse qui si on l’évite pas
peut donner la mort ou des blessures graves. Les dangers possibles sont montrés par les symboles joints ou
sont expliqués dans le texte.
NOTE − Indique des déclarations pas en relation avec des blessures
personnelles.
Indique des instructions spécifiques.
Ce groupe de symboles veut dire Avertissement! Attention! DANGER
DE CHOC ELECTRIQUE, PIECES EN MOUVEMENT, et PIECES
CHAUDES. Consulter les symboles et les instructions ci-dessous y
afférant pour les actions nécessaires afin d’éviter le danger.
2-2. Dangers relatifs au soudage à l’arc
Les symboles présentés ci-après sont utilisés tout au long du
présent manuel pour attirer votre attention et identifier les risques de danger. Lorsque vous voyez un symbole, soyez
vigilant et suivez les directives mentionnées afin d’éviter tout
danger. Les consignes de sécurité présentées ci-après ne
font que résumer l’information contenue dans les normes de
sécurité énumérées à la section 2-7. Veuillez lire et respecter
toutes ces normes de sécurité.
L’installation, l’utilisation, l’entretien et les réparations ne
doivent être confiés qu’à des personnes qualifiées.
Au cours de l’utilisation, tenir toute personne à l’écart et plus
particulièrement les enfants.
UN CHOC ÉLECTRIQUE peut tuer.
Un simple contact avec des pièces électriques peut
provoquer une électrocution ou des blessures graves.
L’électrode et le circuit de soudage sont sous tension
dès que l’appareil est sur ON. Le circuit d’entrée et les circuits
internes de l’appareil sont également sous tension à ce moment-là.
En soudage semi-automatique ou automatique, le fil, le dévidoir, le
logement des galets d’entraînement et les pièces métalliques en
contact avec le fil de soudage sont sous tension. Des matériels mal
installés ou mal mis à la terre présentent un danger.
Ne jamais toucher les pièces électriques sous tension.
Porter des gants et des vêtements de protection secs ne comportant pas de trous.
S’isoler de la pièce et de la terre au moyen de tapis ou d’autres
moyens isolants suffisamment grands pour empêcher le contact
physique éventuel avec la pièce ou la terre.
Ne pas se servir de source électrique à courant électrique dans les
zones humides, dans les endroits confinés ou là où on risque de
tomber.
Se servir d’une source électrique à courant électrique UNIQUEMENT si le procédé de soudage le demande.
Si l’utilisation d’une source électrique à courant électrique s’avère
nécessaire, se servir de la fonction de télécommande si l’appareil
en est équipé.
Des précautions de sécurité supplémentaires sont requises dans
des environnements à risque comme: les endroits humides ou
lorsque l’on porte des vêtements mouillés; sur des structures métalliques au sol, grillages et échafaudages; dans des positions
assises, à genoux et allongées; ou quand il y a un risque important
de contact accidentel avec la pièce ou le sol. Dans ces cas utiliser
les appareils suivants dans l’ordre de préférence: 1) un poste à
souder DC semi−automatique de type CV (MIG/MAG), 2) un poste
à souder manuel (électrode enrobée) DC, 3) un poste à souder
OM-4409 Page 6
manuel AC avec tension à vide réduite. Dans la plupart des cas, un
poste courant continu de type CV est recommandé. Et, ne pas travailler seul!
Couper l’alimentation ou arrêter le moteur avant de procéder à
l’installation, à la réparation ou à l’entretien de l’appareil.
Déverrouiller l’alimentation selon la norme OSHA 29 CFR
1910.147 (voir normes de sécurité).
Installer et mettre à la terre correctement cet appareil conformément à son manuel d’utilisation et aux codes nationaux,
provinciaux et municipaux.
Toujours vérifier la terre du cordon d’alimentation − Vérifier et
s’assurer que le fil de terre du cordon d’alimentation est bien
raccordé à la borne de terre du sectionneur ou que la fiche du
cordon est raccordée à une prise correctement mise à la terre.
En effectuant les raccordements d’entrée fixer d’abord le conducteur de mise à la terre approprié et contre-vérifier les connexions.
Les câbles doivent être exempts d’humidité, d’huile et de graisse;
protégez−les contre les étincelles et les pièces métalliques chaudes.
Vérifier fréquemment le cordon d’alimentation pour voir s’il n’est
pas endommagé ou dénudé − remplacer le cordon immédiatement
s’il est endommagé − un câble dénudé peut provoquer une électrocution.
Mettre l’appareil hors tension quand on ne l’utilise pas.
Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante ou mal épissés.
Ne pas enrouler les câbles autour du corps.
Si la pièce soudée doit être mise à la terre, le faire directement
avec un câble distinct − ne pas utiliser le connecteur de pièce ou le
câble de retour.
Ne pas toucher l’électrode quand on est en contact avec la pièce,
la terre ou une électrode provenant d’une autre machine.
Ne pas toucher des porte électrodes connectés à deux machines
en même temps à cause de la présence d’une tension à vide doublée.
N’utiliser qu’un matériel en bon état. Réparer ou remplacer
sur-le-champ les pièces endommagées. Entretenir l’appareil
conformément à ce manuel.
Porter un harnais de sécurité quand on travaille en hauteur.
Maintenir solidement en place tous les panneaux et capots.
Fixer le câble de retour de façon à obtenir un bon contact métalmétal avec la pièce à souder ou la table de travail, le plus près possible de la soudure.
Isoler la pince de masse quand pas mis à la pièce pour éviter le
contact avec tout objet métallique.
Une tension DC importante subsiste à l’intérieur
des onduleurs après avoir coupé l’alimentation.
Couper l’alimentation du poste et décharger les condensateurs
d’entrée comme indiqué dans la Section Maintenance avant de
toucher des composants.
DES PIÈCES CHAUDES peuvent
provoquer des brûlures graves.
Ne pas toucher à mains nues les parties chaudes.
Prévoir une période de refroidissement avant
de travailler à l’équipement.
Ne pas toucher aux pièces chaudes, utiliser les outils recommandés et porter des gants de soudage et des vêtements épais pour
éviter les brûlures.
DES PIECES DE METAL ou DES
SALETES peuvent provoquer
des blessures dans les yeux.
Le soudage, l’écaillement, le passage de la pièce à la brosse en
fil de fer, et le meulage génèrent des étincelles et des particules
métalliques volantes. Pendant la période de refroidissement des
soudures, elles risquent de projeter du laitier.
Porter des lunettes de sécurité avec écrans latéraux ou un écran
facial.
LES FUMÉES ET LES GAZ peuvent être dangereux.
Le soudage génère des fumées et des gaz. Leur
inhalation peut être dangereux pour votre santé.
Eloigner votre tête des fumées. Ne pas respirer les fumées.
À l’intérieur, ventiler la zone et/ou utiliser une ventilation forcée au
niveau de l’arc pour l’évacuation des fumées et des gaz de soudage.
Si la ventilation est médiocre, porter un respirateur anti-vapeurs
approuvé.
Lire et comprendre les spécifications de sécurité des matériaux
(MSDS) et les instructions du fabricant concernant les métaux, les
consommables, les revêtements, les nettoyants et les dégraisseurs.
Travailler dans un espace fermé seulement s’il est bien ventilé ou
en portant un respirateur à alimentation d’air. Demander toujours à
un surveillant dûment formé de se tenir à proximité. Des fumées et
des gaz de soudage peuvent déplacer l’air et abaisser le niveau
d’oxygène provoquant des blessures ou des accidents mortels.
S’assurer que l’air de respiration ne présente aucun danger.
Ne pas souder dans des endroits situés à proximité d’opérations
de dégraissage, de nettoyage ou de pulvérisation. La chaleur et
les rayons de l’arc peuvent réagir en présence de vapeurs et former des gaz hautement toxiques et irritants.
Ne pas souder des métaux munis d’un revêtement, tels que l’acier
galvanisé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait été enlevé dans la zone de soudure, que l’endroit soit
bien ventilé, et en portant un respirateur à alimentation d’air. Les
revêtements et tous les métaux renfermant ces éléments peuvent
dégager des fumées toxiques en cas de soudage.
LES ACCUMULATIONS DE GAZ risquent de provoquer des blessures ou
même la mort.
Fermer l’alimentation du gaz protecteur en cas
de non utilisation.
Veiller toujours à bien aérer les espaces confinés ou se servir
d’un respirateur d’adduction d’air homologué.
LES RAYONS DE L’ARC peuvent
provoquer des brûlures dans les
yeux et sur la peau.
Le rayonnement de l’arc du procédé de soudage
génère des rayons visibles et invisibles intenses
(ultraviolets et infrarouges) susceptibles de provoquer des brûlures
dans les yeux et sur la peau. Des étincelles sont projetées pendant le
soudage.
Porter un casque de soudage approuvé muni de verres filtrants
approprié pour protéger visage et yeux pendant le soudage
(voir ANSI Z49.1 et Z87.1 énuméré dans les normes de sécurité).
Porter des lunettes de sécurité avec écrans latéraux même sous
votre casque.
Avoir recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements les éblouissements
et les étincelles ; prévenir toute personne sur les lieux de ne pas
regarder l’arc.
Porter des vêtements confectionnés avec des matières résistantes et ignifuges (cuir, coton lourd ou laine) et des bottes de
protection.
LE SOUDAGE peut provoquer un
incendie ou une explosion.
Le soudage effectué sur des conteneurs fermés tels
que des réservoirs, tambours ou des conduites peut
provoquer leur éclatement. Des étincelles peuvent
être projetées de l’arc de soudure. La projection d’étincelles, des
pièces chaudes et des équipements chauds peut provoquer des
incendies et des brûlures. Le contact accidentel de l’électrode avec
des objets métalliques peut provoquer des étincelles, une explosion,
un surchauffement ou un incendie. Avant de commencer le soudage,
vérifier et s’assurer que l’endroit ne présente pas de danger.
Déplacer toutes les substances inflammables à une distance de
10,7 m de l’arc de soudage. En cas d’impossibilité les recouvrir
soigneusement avec des protections homologués.
Ne pas souder dans un endroit là où des étincelles peuvent tomber
sur des substances inflammables.
Se protéger et d’autres personnes de la projection d’étincelles et
de métal chaud.
Des étincelles et des matériaux chauds du soudage peuvent
facilement passer dans d’autres zones en traversant de petites
fissures et des ouvertures.
Surveiller tout déclenchement d’incendie et tenir un extincteur à
proximité.
Le soudage effectué sur un plafond, plancher, paroi ou séparation
peut déclencher un incendie de l’autre côté.
Ne pas effectuer le soudage sur des conteneurs fermés tels que
des réservoirs, tambours, ou conduites, à moins qu’ils n’aient été
préparés correctement conformément à AWS F4.1 (voir les normes de sécurité).
Ne soudez pas si l’air ambiant est chargé de particules, gaz, ou vapeurs inflammables (vapeur d’essence, par exemple).
Brancher le câble de masse sur la pièce le plus près possible de la
zone de soudage pour éviter le transport du courant sur une
longue distance par des chemins inconnus éventuels en provoquant des risques d’électrocution, d’étincelles et d’incendie.
Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
En cas de non utilisation, enlever la baguette d’électrode du porteélectrode ou couper le fil à la pointe de contact.
Porter des vêtements de protection dépourvus d’huile tels que des
gants en cuir, une chemise en matériau lourd, des pantalons sans
revers, des chaussures hautes et un couvre chef.
Avant de souder, retirer toute substance combustible de vos poches telles qu’un allumeur au butane ou des allumettes.
Une fois le travail achevé, assurez−vous qu’il ne reste aucune trace d’étincelles incandescentes ni de flammes.
Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
Suivre les recommandations dans OSHA 1910.252(a)(2)(iv) et
NFPA 51B pour les travaux à chaud et avoir de la surveillance et un
extincteur à proximité.
LE BRUIT peut affecter l’ouïe.
Le bruit des processus et des équipements peut
affecter l’ouïe.
Porter des protections approuvés pour les
oreilles si le niveau sonore est trop élevé.
OM-4409 Page 7
LES CHAMPS MAGNETIQUES peuvent
affecter des implants médicaux.
Porteur de simulateur cardiaque ou autre implants médicaux, rester à distance.
Les porteurs d’implants doivent d’abord consulter leur médecin
avant de s’approcher des opérations de soudage à l’arc, de soudage par points, de gougeage, du coupage plasma ou de chauffage par induction.
Si des BOUTEILLES sont endommagées, elles pourront exploser.
Des bouteilles de gaz protecteur contiennent du gaz
sous haute pression. Si une bouteille est endommagée, elle peut exploser. Du fait que les bouteilles de gaz font
normalement partie du procédé de soudage, les manipuler avec
précaution.
Protéger les bouteilles de gaz comprimé d’une chaleur excessive,
des chocs mécaniques, des dommages physiques, du laitier, des
flammes ouvertes, des étincelles et des arcs.
Placer les bouteilles debout en les fixant dans un support stationnaire ou dans un porte-bouteilles pour les empêcher de tomber ou
de se renverser.
Tenir les bouteilles éloignées des circuits de soudage ou autres
circuits électriques.
Ne jamais placer une torche de soudage sur une bouteille à gaz.
Une électrode de soudage ne doit jamais entrer en contact avec
une bouteille.
Ne jamais souder une bouteille pressurisée − risque d’explosion.
Utiliser seulement des bouteilles de gaz protecteur, régulateurs,
tuyaux et raccords convenables pour cette application spécifique;
les maintenir ainsi que les éléments associés en bon état.
Ne pas tenir la tête en face de la sortie en ouvrant la soupape de la
bouteille.
Maintenir le chapeau de protection sur la soupape, sauf en cas
d’utilisation ou de branchement de la bouteille.
Utiliser les équipements corrects, les bonnes procédures et suffisamment de personnes pour soulever et déplacer les bouteilles.
Lire et suivre les instructions sur les bouteilles de gaz comprimé,
l’équipement connexe et le dépliant P-1 de la CGA (Compressed Gas
Association) mentionné dans les principales normes de sécurité.
2-3. Dangers existant en relation avec le moteur
L’EXPLOSION DE LA BATTERIE
peut RENDRE AVEUGLE.
Toujours porter une protection faciale, des gants
en caoutchouc et vêtements de protection lors
d’une intervention sur la batterie.
Arrêter le moteur avant de débrancher ou de brancher les câbles
de batterie.
Eviter de provoquer des étincelles avec les outils en travaillant sur
la batterie.
Ne pas utiliser le poste de soudage pour charger les batteries ou
des véhicules de démarrage rapide.
Observer la polarité correcte (+ et −) sur les batteries.
Débrancher le câble négatif (–) en premier lieu. Le rebrancher en
dernier lieu.
LE CARBURANT MOTEUR peut provoquer un incendie ou une explosion.
Arrêter le moteur avant de vérifier le niveau de
carburant ou de faire le plein.
Ne pas faire le plein en fumant ou proche d’une source d’étincelles ou d’une flamme nue.
Ne pas faire le plein de carburant à ras bord; prévoir de l’espace
pour son expansion.
Faire attention de ne pas renverser de carburant. Nettoyer tout
carburant renversé avant de faire démarrer le moteur.
Jeter les chiffons dans un récipient ignifuge.
Toujours garder le pistolet en contact avec le réservoir lors du
remplissage.
DES ORGANES MOBILES peuvent
provoquer des blessures.
Ne pas approcher les mains des ventilateurs,
courroies et autres pièces en mouvement.
Maintenir fermés et fixement en place les portes, panneaux, recouvrements et dispositifs de protection.
Arrêter le moteur avant d’installer ou brancher l’appareil.
OM-4409 Page 8
Seules des personnes qualifiées sont autorisées à enlever les portes, panneaux, recouvrements ou dispositifs de protection pour
effectuer, s’il y a lieu, des travaux d’entretien et de dépannage.
Pour empêcher tout démarrage accidentel pendant les travaux
d’entretien, débrancher le câble négatif (−) de batterie de la borne.
Ne pas approcher les mains, cheveux, vêtements lâches et outils
des organes mobiles.
Remettre en place les panneaux ou les dispositifs de protection et
fermer les portes à la fin des travaux d’entretien et avant de faire
démarrer le moteur.
Avant d’intervenir, déposer les bougies ou injecteurs pour éviter la
mise en route accidentelle du moteur.
Bloquer le volant moteur pour éviter sa rotation lors d’une intervention sur le générateur.
DES PIÈCES CHAUDES peuvent
provoquer des brûlures graves.
Ne pas toucher à mains nues les parties chaudes.
Prévoir une période de refroidissement avant de
travailler à l’équipement.
Ne pas toucher aux pièces chaudes, utiliser les outils recommandés et porter des gants de soudage et des vêtements épais pour
éviter les brûlures.
LA VAPEUR ET LE LIQUIDE DE
REFROIDISSEMENT CHAUD peuvent
provoquer des brûlures.
Il est préférable de vérifier le liquide de refroidissement une fois le moteur refroidi pour éviter
de se brûler.
Toujours vérifier le niveau de liquide de refroidissement dans le
vase d’expansion (si présent), et non dans le radiateur (sauf si précisé autrement dans la section maintenance du manuel du
moteur).
Si le moteur est chaud et que le liquide doit être vérifié, opérer comme suivant.
Mettre des lunettes de sécurité et des gants, placer un torchon sur
le bouchon du radiateur.
Dévisser le bouchon légèrement et laisser la vapeur s’échapper
avant d’enlever le bouchon.
L’utilisation d’un groupe autonome
à l’intérieur PEUT VOUS TUER EN
QUELQUES MINUTES.
Les fumées d’un groupe autonome contient du
monoxyde de carbone. C’est un poison invisible et inodore.
JAMAIS utiliser dans une maison ou garage,
même avec les portes et fenêtres ouvertes.
Uniquement utiliser à l’EXTERIEUR, loin des portes, fenêtres et
bouches aération.
L’ACIDE DE LA BATTERIE peut provoquer des brûlures dans les YEUX et
sur la PEAU.
Ne pas renverser la batterie.
Remplacer une batterie endommagée.
Rincer immédiatement les yeux et la peau à l’eau.
LA CHALEUR DU MOTEUR peut provoquer un incendie.
Ne pas placer l’appareil sur, au-dessus ou à
proximité de surfaces inflammables.
Tenir à distance les produits inflammables de l’échappement.
LES ÉTINCELLES À L’ÉCHAPPEMENT
peuvent provoquer un incendie.
Empêcher les étincelles d’échappement du
moteur de provoquer un incendie.
Utiliser uniquement un pare-étincelles
approuvé − voir codes en vigueur.
2-4. Dangers liés à l’air comprimé
RESPIRER L’AIR COMPRIMÉ peut provoquer des blessures graves ou causer
la mort.
Le METAL CHAUD lors du coupage et
gougeage plasma peut provoquer un incendie ou une explosion.
Ne pas utiliser l’air comprimé pour respirer.
Utiliser l’air comprimé seulement pour le coupage, gougeage et les outils pneumatiques.
Ne pas couper ou gouger à proximité de produits inflammables.
Surveillez et garder un extincteur à proximité.
L’AIR COMPRIMÉ peut provoquer
des blessures.
Porter des lunettes de sécurité approuvées.
Ne pas diriger le jet d’air vers d’autres ou
soi-même.
L’AIR COMPRIME EMMAGASINE ET DES
TUYAUX SOUS PRESSION peuvent provoquer des blessures.
Relâcher la pression d’air de l’outillage ou du
système avant d’effectuer la maintenance,
avant de changer ou de rajouter des éléments
ou avant d’ouvrir la purge ou le bouchon de
remplissage d’huile.
DES PIECES CHAUDES peuvent provoquer des brûlures et blessures.
Ne pas toucher le compresseur ou d’autres
éléments du circuit air comprimé chauds.
Laisser l’ensemble se refroidir avant de toucher ou d’effectuer la
maintenance.
LIRE LES INSTRUCTIONS.
Lisez le manuel d’instructions avant l’utilisation
ou la maintenance de l’appareil.
Arrêter le moteur et relâcher la pression avant
d’effectuer la maintenance.
N’utiliser que les pièces de rechange recommandées par le
constructeur.
2-5. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance
Risque D’INCENDIE OU D’EXPLOSION.
Ne pas placer l’appareil sur, au-dessus ou
à proximité de surfaces inflammables.
Ne pas installer l’appareil à proximité de produits inflammables.
Ne pas surcharger l’installation électrique − s’assurer que l’alimentation est correctement dimensionnée et protégée avant de
mettre l’appareil en service.
LA CHUTE DE L’APPAREIL peut blesser.
Utiliser l’anneau de levage pour lever l’appareil
et les accessoires correctement installées
seuls, PAS les bouteilles de gaz. Ne pas dépasser le poids nominal maximal de l’œilleton
(voir les spécifications).
Ne lever et ne soutenir l’appareil qu’avec de
l’équipement approprié et en suivant les
procédures adéquates.
En utilisant des fourches de levage pour déplacer l’unité, s’assurer que les fourches sont suffisamment longues pour dépasser
du côté opposé de l’appareil.
OM-4409 Page 9
UNE REMORQUE QUI BASCULE peut
entraîner des blessures.
LE SURCHAUFFEMENT peut endommager le moteur électrique.
Utiliser les supports de la remorque ou des
blocs pour soutenir le poids.
Installer convenablement le poste sur la remorque comme indiqué dans le manuel s’y rapportant.
Arrêter ou déconnecter l’équipement avant de
démarrer ou d’arrêter le moteur.
Ne pas laisser tourner le moteur trop lentement sous risque d’endommager le moteur électrique à cause d’une tension et d’une fréquence trop faibles.
Ne pas brancher de moteur de 50 ou de 60 Hz à la prise de 100 Hz,
s’il y a lieu.
LES ÉTINCELLES VOLANTES risquent de provoquer des blessures.
Porter un écran facial pour protéger le visage et
les yeux.
Affûter l’électrode au tungstène uniquement à
la meuleuse dotée de protecteurs. Cette manœuvre est à exécuter dans un endroit sûr lorsque l’on porte l’équipement homologué de protection du visage, des mains et du corps.
Les étincelles risquent de causer un incendie − éloigner toute
substance inflammable.
LIRE LES INSTRUCTIONS.
Lisez le manuel d’instructions avant l’utilisation
ou la maintenance de l’appareil.
N’utiliser que les pièces de rechange recommandées par le constructeur.
Effectuer la maintenance et le service du moteur et du compresseur d’air suivant les instructions dans ce manuel ou le manuel
du moteur/compresseur (si applicable).
LE RAYONNEMENT HAUTE FRÉQUENCE (H.F.) risque de provoquer
des interférences.
DES ORGANES MOBILES peuvent
provoquer des blessures.
Ne pas s’approcher des organes mobiles.
Ne pas s’approcher des points de coincement
tels que des rouleaux de commande.
LES FILS DE SOUDAGE peuvent
provoquer des blessures.
Ne pas appuyer sur la gâchette avant d’en
avoir reçu l’instruction.
Ne pas diriger le pistolet vers soi, d’autres personnes ou toute pièce mécanique en engageant le fil de soudage.
LE SOUDAGE À L’ARC risque de
provoquer des interférences.
L’EMPLOI EXCESSIF peut
SURCHAUFFER L’ÉQUIPEMENT.
Laisser l’équipement refroidir ; respecter le facteur de marche nominal.
Réduire le courant ou le facteur de marche
avant de poursuivre le soudage.
Ne pas obstruer les passages d’air du poste.
LES CHARGES ÉLECTROSTATIQUES peuvent endommager les
circuits imprimés.
Établir la connexion avec la barrette de terre
avant de manipuler des cartes ou des pièces.
Utiliser des pochettes et des boîtes antistatiques pour stocker,
déplacer ou expédier des cartes de circuits imprimes.
OM-4409 Page 10
Le rayonnement haute fréquence (H.F.) peut
provoquer des interférences avec les équipements de radio−navigation et de communication, les services de sécurité et les ordinateurs.
Demander seulement à des personnes qualifiées familiarisées
avec des équipements électroniques de faire fonctionner l’installation.
L’utilisateur est tenu de faire corriger rapidement par un électricien qualifié les interférences résultant de l’installation.
Si le FCC signale des interférences, arrêter immédiatement l’appareil.
Effectuer régulièrement le contrôle et l’entretien de l’installation.
Maintenir soigneusement fermés les portes et les panneaux des
sources de haute fréquence, maintenir les éclateurs à une distance correcte et utiliser une terre et un blindage pour réduire les
interférences éventuelles.
L’énergie électromagnétique risque de provoquer des interférences pour l’équipement électronique sensible tel que les ordinateurs et
l’équipement commandé par ordinateur tel que
les robots.
Veiller à ce que tout l’équipement de la zone de soudage soit
compatible électromagnétiquement.
Pour réduire la possibilité d’interférence, maintenir les câbles de
soudage aussi courts que possible, les grouper, et les poser
aussi bas que possible (ex. par terre).
Veiller à souder à une distance de 100 mètres de tout équipement électronique sensible.
Veiller à ce que ce poste de soudage soit posé et mis à la terre
conformément à ce mode d’emploi.
En cas d’interférences après avoir pris les mesures précédentes, il incombe à l’utilisateur de prendre des mesures supplémentaires telles que le déplacement du poste, l’utilisation de câbles blindés, l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone de travail.
2-6. Proposition californienne 65 Avertissements
Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des malformations congénitales et, dans certains cas, des cancers.
(Code de santé et de sécurité de Californie, chapitre 25249.5
et suivants)
Les batteries, les bornes et autres accessoires contiennent
du plomb et des composés à base de plomb, produits chimiques dont l’État de Californie reconnaît qu’ils provoquent des
cancers et des malformations congénitales ou autres
problèmes de procréation. Se laver les mains après manipulation.
Pour les moteurs à essence :
Les gaz d’échappement des moteurs contiennent des produits chimiques dont l’État de Californie reconnaît qu’ils
provoquent des cancers et des malformations congénitales
ou autres problèmes de procréation.
Pour les moteurs diesel :
Les gaz d’échappement des moteurs diesel et certains de
leurs composants sont reconnus par l’État de Californie comme provoquant des cancers et des malformations
congénitales ou autres problèmes de procréation.
2-7. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
de Global Engineering Documents (téléphone : 1-877-413-5184, site
Internet : www.global.ihs.com).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1 de Global Engineering Documents (téléphone :
1-877-413-5184, site Internet : www.global.ihs.com).
National Electrical Code, NFPA Standard 70, de National Fire Protection Association, P.O. Box 9101, Quincy, MA 02269-9101 (téléphone :
617-770-3000, site Internet : www.nfpa.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
de Compressed Gas Association, 4221 Walney Road, 5th Floor, Chantilly, VA 20151 (téléphone : 703-788-2700, site Internet :
www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, de
Canadian Standards Association, 5060 Mississauga, Ontario, Canada
L4W 5NS (téléphone : 800-463-6727 ou à Toronto 416-747-4044, site
Internet : www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, de American National Standards Institute,
11 West 43rd Street, New York, NY 10036-8002 (téléphone :
212-642-4900, site Internet : www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, de National Fire Protection Association,
P.O. Box 9101, Quincy, MA 02269-9101 (téléphone : 617-770-3000,
site Internet : www.nfpa.org).
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, de U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(téléphone : 1-866-512-1800) (il y a 10 bureaux régionaux−−le téléphone de la région 5, Chicago, est 312-353-2220, site Internet :
www.osha.gov).
2-8. Information EMF
Considérations sur le soudage et les effets de basse fréquence et des
champs magnétiques et électriques.
Le courant de soudage, pendant son passage dans les câbles de soudage, causera des champs électromagnétiques. Il y a eu et il y a encore
un certain souci à propos de tels champs. Cependant, après avoir examiné plus de 500 études qui ont été faites pendant une période de
recherche de 17 ans, un comité spécial ruban bleu du National
Research Council a conclu : « L’accumulation de preuves, suivant le
jugement du comité, n’a pas démontré que l’exposition aux champs
magnétiques et champs électriques à haute fréquence représente un
risque à la santé humaine ». Toutefois, des études sont toujours en
cours et les preuves continuent à être examinées. En attendant que les
conclusions finales de la recherche soient établies, il vous serait
souhaitable de réduire votre exposition aux champs électromagnétiques pendant le soudage ou le coupage.
Pour réduire les champs magnétiques sur le poste de travail, appliquer
les procédures suivantes :
1. Garder les câbles ensemble, les torsader, les scotcher, ou les
recouvrir d’une housse.
2. Disposer les câbles d’un côté et à distance de l’opérateur.
3. Ne pas courber pas et ne pas entourer pas les câbles autour de
votre corps.
4. Garder le poste de soudage et les câbles le plus loin possible de
vous.
5. Connecter la pince sur la pièce aussi près que possible de la
soudure.
En ce qui concerne les implants médicaux :
Les porteurs d’implants doivent d’abord consulter leur médecin avant
de s’approcher des opérations de soudage à l’arc, de soudage par
points, de gougeage, du coupage plasma ou de chauffage par induction. Si le médecin approuve, il est recommandé de suivre les
procédures précédentes.
OM-4409 Page 11
SECTION 3 − DEFINITIONS
3-1. Symbols And Definitions
Stop Engine
Fast (Run, Weld/
Power)
Slow (Idle)
Start Engine
Check engine belt
Check Air Cleaner
Starting Aid
Engine
Battery (Engine)
Jump start/Battery
Charge
Battery Charge
Jump Start
Do Not Switch
Under Load
Read Operator’s
Manual
Certified/Trained
Mechanic
Engine Oil
Check Injectors/
Pump
Check Valve
Clearance
Fuel
Engine Coolant
Temperature
Hourmeter (HM)
Air Pressure
Temperature
Air Compressor
Positive
Negative
Wire Feed
Welding Arc
Volts
Panel/Local
Remote
Output
Direct Current
(DC)
Alternating
Current (AC)
Gas Tungsten Arc
Welding (TIG)
Stick (SMAW)
Welding
Constant Current
(CC)
MIG (GMAW)
Welding
Constant Voltage
(CV)
Single Phase
Air Carbon Arc
Cutting (CAC-A)
Protective Earth
(Ground)
DC Electrode
Positive
DC Electrode
Negative
Work Connection
Electrode
Connection
Circuit Protector
Time
On
Off
OPT
A
V
Amperes
3
Three Phase
OM-4409 Page 12
1
h
Hours
s
Seconds
SECTION 4 − SPECIFICATIONS
4-1. Weld, Power, And Engine Specifications
Welding
Mode
Weld
Output
Range
CC/DC
20 − 750 A
CV/DC
CC/AC
(Optional)
Battery
Charge/
Jump
Start
14 − 40 V
20 - 575
12/24 V
Rated
Welding
Output
500 A,
40 Volts
DC,
100% Duty
Cycle
600 A,
44 Volts
DC,
40% Duty
Cycle
750 A,
12 Volt
Jump Start
750 A,
24 Volt
Jump Start
Maximum
Open-Circuit
Voltage
(Nominal)
Generator Power
Rating
Engine
Standard
Single-Phase,
4 kVA/kW, 34/17 A,
120/240 V AC,
50/60 Hz
DEUTZ
Engine
Oil
Capacity
Fuel Tank
Capacity
11 qt
(10.4 L)
25 gal
(95 L)
95
56
64
14/28
3-Phase Generator
Option*
Single-Phase/Three-Phase,
12/20 kVA/kW, 50/48A,
120/240 VAC, 60 Hz
Deutz BF4M2011
Oil-Cooled,
Four-Cylinder,
Turbo-Charged
63.4 HP Diesel Engine
*In Addition To Standard
4 kVA/kW Generator Power
4-2. Air Compressor Specifications
Compressor Model
And Type
Air Output At Effective
Working Pressure
Factory Pressure
Setting
Safety Relief
Valve Rating
Air Compressor
Oil Capacity
Ingersoll Rand CE55 G
Rotary Screw
60 scfm (1.7 m3 min−1),
100 psi (690 kPa),
100% Duty Cycle
125 psi (862 kPa)
150 psi (1034 kPa)
4 qt (3.8 L)
Idle Speed (1235 rpm)
Weld/Power Speed
(1850 rpm)
40 Volts DC At 500
Amps
44 Volts DC At 600
Amps
96.6 Lwa sound power
102.8 Lwa sound power
103.9 Lwa sound power
106.0 Lwa sound power
71.7 dBa at 23 ft (7 m)
77.2 dBA 3.3 ft (1 m)
from front panel
77.9 dBa at 23 ft (7 m)
83.0 dBA 3.3 ft (1 m)
from front panel
79.0 dBa at 23 ft ( 7 m)
89.8 dBA 3.3 ft (1 m)
from front panel
81.1 dBa at 23 ft (7 m)
93.3 dBA 3.3 ft (1 m)
from front panel
94.6 Lwa sound power
100.6 Lwa sound power
103.0 Lwa sound power
104.5 Lwa sound power
69.7 dBa at 23 ft (7 m)
74.5 dBA 3.3 ft (1 m)
from front panel
75.7dBa at 23 ft (7 m)
78.8 dBA 3.3 ft (1 m)
from front panel
78.1dBa at 23 ft (7 m)
86.0 dBA 3.3 ft (1 m)
from front panel
79.6 dBa at 23 ft (7 m)
91.8 dBA 3.3 ft (1 m)
from front panel
4-3. Sound Level Table
Air Compressor On
Air Compressor Off
OM-4409 Page 13
4-4. Dimensions, Weights, And Operating Angles
Dimensions
Height
Width
54-1/2 in (1384 mm)
(to top of muffler)
G
28-1/2 in (724 mm)
(mtg. brackets turned in)
30-3/4 in (781 mm)
(mtg. brackets turned out)
Depth
69-1/2 in (1765 mm)
A
69-1/2 in (1765 mm)
B*
55-7/8 in (1419 mm)
C*
46-3/8 in (1178)
D*
11 in (279 mm)
E
27-1/2 in (699 mm)
F
1 in (25 mm)
G
29-13/16 in (757 mm)
H
9/16 in (14 mm) Dia.
4 Holes
* With mounting brackets in center
position. Dimensions vary with location of mounting brackets.
Weight
No fuel: 2010 lb (907 kg)
w/fuel: 2185 lb (993 kg)
Lifting Eye Weight Rating
2185 lb (993 kg) Maximum
!
Do not exceed tilt angles or engine could
be damaged or unit could tip.
!
Do not move or operate unit where it could
tip.
A
B
C
30°
H
D
20°
Front Panel End
30°
20°
F
E
802 161-A
803 231
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-4409 Page 14
4-5. Stick And MIG Volt-Ampere Curves
A. DC Stick Mode
100
Ranges
300 − Max
185 − 525
125 − 400
85 − 250
55 − 125
80
DC VOLTS
The volt-ampere curve shows the
minimum and maximum voltage
and amperage output capabilities of
the welding generator. Curves of all
other settings fall between the
curves shown.
60
40
20
0
0
100
200
300
400 500 600
DC AMPERES
700
800
900
1000
B. AC Stick Mode (Optional)
100
AC VOLTS
80
60
40
20
0
0
100
200
300
400
500
600
700
AC AMPERES
C. MIG Mode
100
DC VOLTS
80
60
MAX
40
MIN
20
0
0
100
200
300
400 500 600
DC AMPERES
700
800
900
1000
208 135 / 203 415 / 208 956
OM-4409 Page 15
4-6. TIG Volt-Ampere Curves
The volt-ampere curve shows the
minimum and maximum voltage
and amperage output capabilities of
the welding generator. Curves of all
other settings fall between the
curves shown.
A. DC TIG Mode
100
Ranges
60−450
40−330
30−220
20−110
DC VOLTS
80
60
40
20
0
0
50 100 150 200 250 300 350 400 450 500 550 600 650 700
DC AMPERES
B. AC TIG Mode (Optional)
100
AC VOLTS
80
60
40
20
0
0
100
200
300
400
500
600
700
AC AMPERES
208 136 / 208 957
OM-4409 Page 16
US Gal./Hr.
4-7. Fuel Consumption
3.00
2.75
2.50
2.25
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0.00
The curve shows typical fuel use
under weld or generator power
loads.
w/ Air Output
IDLE
0
50
100 150 200 250 300 350 400 450 500 550 600
DC WELD AMPERES AT 100% DUTY CYCLE
208 211
4-8. Duty Cycle And Overheating
100% Duty Cycle At 500 Amperes
Duty Cycle is percentage of 10 minutes that unit can weld at rated load
without overheating.
NOTICE − Exceeding duty cycle
can damage unit and void warranty.
Continuous Welding
40% Duty Cycle At 600 Amperes
4 Minutes Welding
6 Minutes Resting
1000
WELD AMPERES
800
600
500
400
300
250
200
150
100
10
15
20
25
30
40
% DUTY CYCLE
50
60
80
100
202 356
OM-4409 Page 17
4-9. Generator AC Power Curve
AC VOLTS
The ac power curve shows the generator power in amperes available
at the 120 and 240 volt receptacles.
150
300
125
250
100
200
75
150
50
100
25
50
0
0
0
5
10
15
20
AC AMPERES IN 240V MODE
25
30
0
10
20
30
40
AC AMPERES IN 120V MODE
50
60
193 018
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-4409 Page 18
4-10. Optional 3-Phase Generator Power Curves
The ac power curves show the generator power available in amperes
at the single-phase 120/240 volt receptacle or three-phase 240 volt
terminals.
A. 12 kVA/kW Single-Phase AC Output (No Weld Load)
140 280
135 270
125 250
120 240
115 230
110 220
105 210
100 200
95 190
90 180
20
0
40
60
80
100
AC AMPERES
B. 20 kVA/kW Three-Phase AC Output (No Weld Load)
280
260
AC VOLTS
AC VOLTS
130 260
240
220
200
180
0
10
20
30
40
50
60
70
AC AMPERES
197 472 / 197 473
OM-4409 Page 19
4-11. Air Compressor Output Curve
The air output curve shows the volume and pressure of air available
from the air compressor.
POUNDS PER SQUARE INCH (PSI)
140
120
100
80
Idle
60
40
20
0
0
10
20
30
40
50
60
70
80
90
100
CUBIC FEET PER MINUTE (CFM)
208 955
4-12. Optional Battery Charging Output Curve
The battery charging curves show
the charging amperage and voltage
output of the welding generator.
As battery voltage nears the charging voltage, charging current decreases.
50
45
40
DC VOLTS
35
30
25
20
15
10
5
0
0
100
200
300
400
500
600
700
800
900
1000
DC AMPERES
210 269
OM-4409 Page 20
SECTION 5 − INSTALLATION
5-1. Installing Welding Generator
Movement
!
Do not move or operate unit
where it could tip.
!
Always securely fasten welding generator onto transport
vehicle or trailer and comply
with all DOT and other applicable codes.
NOTICE − Do not install unit where
air flow is restricted or engine may
overheat.
OR
OR
See Section 4-4 for lifting eye
rating.
See Section 5-2 for mounting information.
Location/Airflow Clearance
OR
18 in
(460 mm)
18 in
(460 mm)
18 in
(460 mm)
OR
18 in
(460 mm)
18 in
(460 mm)
install3 2008-01 − Ref. 800 652 / Ref. 800 477-A / 803 274 / 804 712
OM-4409 Page 21
5-2. Mounting Welding Generator
!
Supporting The Unit
Do not weld on base. Welding on base can cause fuel
tank fire or explosion. Weld
only on the four mounting
brackets or bolt unit down.
NOTICE − Do not mount unit by
supporting the base only at the four
mounting brackets. Use crosssupports to adequately support unit
and prevent damage to base.
2
Mounting Surface:
1
2
OR
Cross-Supports
Mounting Brackets (Supplied)
Mount unit on flat surface or use
cross-supports to support base.
Secure unit with mounting brackets.
3
1
4
1/2 in Bolt And Washer
(Minimum − Not Supplied)
3/8-16 x 1 in Screws
(Supplied)
To Bolt Unit In Place:
Remove hardware securing the
four mounting brackets to the base.
Reverse brackets and reattach to
base with original hardware.
1
Mount unit to truck or trailer with 1/2
in (12 mm) or larger hardware (not
supplied).
Using Mounting Brackets
To Weld Unit In Place:
Weld unit to truck or trailer only at
the four mounting brackets.
2
Welding Unit In Place
Bolting Unit In Place
3
2
4
Tools Needed:
9/16 in
install3 2008--01 803 274 / 200 864-A / 803 231
OM-4409 Page 22
5-3. Grounding Generator To Truck Or Trailer Frame
1
!
Always ground generator
frame to vehicle frame to prevent electric shock and static
electricity hazards.
!
Also see AWS Safety &
Health Fact Sheet No. 29,
Grounding of Portable And
Vehicle Mounted Welding
Generators.
!
Bed liners, shipping skids,
and some running gear insulate the welding generator
from the vehicle frame. Always connect a ground wire
from the generator equipment grounding terminal to
bare metal on the vehicle
frame as shown.
!
If unit does not have GFCI receptacles, use GFCI-protected extension cord.
1
Equipment Grounding
Terminal (On Front Panel)
Grounding Cable (Not
Supplied)
Metal Vehicle Frame
2
GND/PE
2
3
3
Connect cable from equipment
ground terminal to metal vehicle
frame. Use #10 AWG or larger
insulated copper wire.
Electrically
bond generator
frame to vehicle frame by metal-to-metal contact.
rot_grnd 2008-01 − 800 652-D
5-4. Rating Label Location
4
1
Rating Label − Typical
Locate rating label on unit. Label provides information such as weld output
ratings, generator ratings, and engine
information.
Evidence of label tampering voids
warranty.
rot_label 2008-01 − 804 712
OM-4409 Page 23
5-5. Installing Optional Spark Arrestor Muffler
2
Stop engine and let cool.
1
2
3
4
5
6
7
8
9
10
Spark Arrestor Muffler
Double-Flanged Elbow
Nut
Flat Washer
Mount
Bracket
Screw
Single-Flanged Elbow
Rain Cap
Clamp
Loosely assemble components as
shown.
1
10
!
Mount the muffler with the clean-
9
out plug to the outside.
After assembly, final-tighten
clamps and hardware.
all
Be
sure to tighten rain cap
mounting screw.
7
6
8
5
4
3
Tools Needed:
7/16, 1/2 in
OM-4409 Page 24
803 230
5-6. Activating The Dry Charge Battery (If Applicable)
!
3
Always wear a face shield,
rubber gloves and protective
clothing when working on a
battery.
Remove battery from unit.
1
2
2
1
3
Vent Caps
Sulfuric Acid Electrolyte
(1.265 Specific Gravity)
Well
Fill each cell with electrolyte to
bottom of well (maximum).
!
Do not overfill battery cells.
Wait ten minutes and check electrolyte level. If necessary, add electrolyte to raise to proper level. Reinstall vent caps.
4
Battery Charger
!
Read and follow all instructions supplied with battery
charger.
5
5 Amperes For 30 Minutes
Charge Time
30 Amperes For 12 Minutes
Charge Time
6
5
4
Charge battery. Disconnect charging cables and install battery.
When electrolyte
is low, add
only distilled water to cells to
maintain proper level.
5A
+
6
−
Tools Needed:
30 A
drybatt1 2008−01 − S-0886
5-7. Connecting The Battery
!
Connect negative (−) battery
cable last.
Reinstall
cover after connecting
battery.
+
−
Tools Needed:
1/2 in
802 168-E / Ref. 202 705 / 802 313 / S-0756-C
OM-4409 Page 25
5-8. Using The Optional Battery Disconnect Switch
1
OFF
ON
!
Stop engine.
1
Battery Disconnect Switch
The battery disconnect switch disconnects battery voltage from the
circuit. When the switch is turned
Off, the front panel controls do not
work.
To run unit, turn switch to On position. To prevent unit from running,
turn switch to Off position.
The switch may be locked using a
customer-supplied padlock.
803 228 / Ref. 803 324
Notes
Start Your Professional
Welding Career Now!
OM-4409 Page 26
400 Trade Square East, Troy, Ohio 45373
1-800-332-9448 www.welding.org
Over 80,000 trained
since 1930!
5-9. Engine/Compressor Prestart Checks
Engine Oil
Compressor
Oil
Full
Diesel
1
Too
High
Full
Too
Low
Full
803 228
Check
all engine/compressor fluids
daily.
Engine must be cold and on a level surface.
Unit is shipped with 20W break-in oil. The
automatic shutdown system stops engine if
oil pressure is too low or coolant temperature is too high.
This unit has a low oil pressure shut-
down switch. However, some conditions may cause engine damage before
the engine shuts down. Check oil level
often and do not use the oil pressure
shutdown system to monitor oil level.
Follow run-in procedure in engine manual.
If unburned fuel and oil collect in exhaust
pipe during run-in, see Section 14.
Fuel
NOTICE − Do not use gasoline. Gasoline
will damage engine.
Add fresh diesel fuel before starting to prevent air from entering the fuel system (see
engine maintenance label for fuel specifications). Leave filler neck empty to allow room
for expansion.
Engine stops if fuel level is low.
Engine Oil
After fueling, check oil with unit on level surface. If oil is not up to full mark on dipstick,
add oil (see maintenance label for engine oil
specifications).
Compressor Oil
1 Compressor Oil Level Indicator (On
Tank)
Check oil with unit on level surface. Add oil
if oil is not up to full mark on indicator (see
maintenance label for oil specifications).
Cold Weather Starting
To improve cold weather starting:
Use Starting Aid switch (see Section
6-1).
Keep battery in good condition. Store
battery in warm area.
Use fuel formulated for cold weather
(diesel fuel can gel in cold weather).
Contact local fuel supplier for fuel information.
Use correct grade oil for cold weather
(see Section 9-1).
OM-4409 Page 27
5-10. Connecting To Weld Output Terminals
Stick And TIG Welding
MIG And FCAW Welding
For Stick welding Direct Current Electrode
Positive (DCEP), connect electrode holder cable to Positive (+) terminal on left and
work cable to Negative (−) terminal on
right.
For MIG welding Direct Current Electrode
Positive (DCEP), connect wire feeder
cable to Positive (+) terminal on left and
work cable to Negative (−) terminal on
right. Use Process/Contactor switch to
select type of weld output (see Section
6-3).
For Stick and TIG Direct Current Electrode Negative (DCEN), connect electrode holder cable to Negative (−) terminal
on right and work cable to Positive (+) terminal on left.
If equipped with optional Polarity/AC Selector switch, connect electrode holder
cable to Electrode terminal on left and
work cable to Work terminal on right.
!
Stop engine.
1
Positive (+) Weld Output Terminal
2
Negative (−) Weld Output Terminal
!
Failure to properly connect weld
cables may cause excessive heat and
start a fire, or damage your machine.
3
4
5
6
Weld Output Terminal
Supplied Weld Output Terminal Nut
Weld Cable Terminal
Copper Bar
For MIG and FCAW Direct Current Electrode Negative (DCEN), connect wire
feeder cable to Negative (−) terminal on
right and work cable to Positive (+) terminal on left. Use Process/Contactor switch
to select type of weld output (see Section
6-3).
If equipped with optional Polarity/AC Selector switch, connect wire feeder cable to
Electrode terminal on left and work cable
to Work terminal on right.
Remove supplied nut from weld output terminal. Slide weld cable terminal onto weld output
terminal and secure with nut so that weld cable
terminal is tight against copper bar. Do not
place anything between weld cable terminal and copper bar. Make sure that the surfaces of the weld cable terminal and copper bar are clean.
Tools Needed:
3/4 in
1
2
3
6
Do not place
anything between
weld cable terminal
and copper bar.
4
5
Correct Installation
OM-4409 Page 28
Incorrect Installation
803 231 / 803 778-A
5-11. Selecting Weld Cable Sizes*
Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit
Not Exceeding***
Weld Output
Terminals
!
Turn off power before
connecting to weld
output terminals.
!
Do not use worn, damaged, undersized, or
poorly spliced cables.
* This
100 ft (30 m) or Less
150 ft
(45 m)
200 ft
(60 m)
250 ft
(70 m)
300 ft
(90 m)
350 ft
400 ft
(105 m) (120 m)
Welding
Amperes
10 − 60%
Duty
Cycle
60 − 100%
Duty
Cycle
100
4 (20)
4 (20)
4 (20)
3 (30)
2 (35)
1 (50)
1/0 (60)
1/0 (60)
150
3 (30)
3 (30)
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
3/0 (95)
200
3 (30)
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
4/0 (120)
250
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 2/0
(2x70)
300
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 3/0
(2x95)
350
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
400
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
2 ea. 4/0
(2x120)
500
2/0 (70)
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
3 ea. 3/0
(3x95)
600
3/0 (95)
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
3 ea. 4/0
(3x120)
3 ea. 4/0
(3x120)
700
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 3/0
(3x95)
3 ea. 4/0
(3x120)
3 ea. 4/0
(3x120)
4 ea. 4/0
(4x120)
800
4/0 (120)
2 ea. 2/0
(2x70)
2 ea. 3/0
(2x95)
2 ea. 4/0
(2x120)
3 ea. 4/0
(3x120)
3 ea. 4/0
(3x120)
4 ea. 4/0
(4x120)
4 ea. 4/0
(4x120)
10 − 100% Duty Cycle
chart is a general guideline and may not suit all applications. If cable overheats, use next size larger cable.
**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.
( ) = mm2 for metric use
S-0007-F
***For distances longer than those shown in this guide, call a factory applications representative at 920-735-4505.
Notes
OM-4409 Page 29
5-12. Connecting To Remote 14 Receptacle RC14
Socket*
Socket Information
A
24 volts ac. Protected by supplementary protector CB5.
B
Contact closure to A completes
24 volt ac contactor control
circuit.
C
Output to remote control:+10
volts dc in MIG or Stick mode;
0 to +10 volts dc in TIG mode.
D
Remote control circuit common.
E
DC input command signal: 0 to
+10 volts from min. to max. of
remote control with Voltage/
Amperage Adjust control at
max.
24 VOLTS AC
REMOTE
OUTPUT
CONTROL
OR
GND
NEUTRAL
Notes
OM-4409 Page 30
115 volts, 10 amperes, 60 Hz
ac. Protected by supplementary
protector CB6.
J
Contact closure to I completes
115 volt ac contactor control
circuit.
K
Chassis common.
G
Circuit common for 24 and 115
volt ac circuit.
115 VOLTS AC
803 231
*The remaining sockets are not used.
I
5-13. Connecting To The Air Compressor
!
Stop engine and release air pressure before servicing compressor.
2
Open Position
1
Closed Position
803 231
!
Air pressure is present at air shutoff
valve whenever Air Pressure Gauge
on front panel indicates air
pressure.
1
3/4 in NPT Air Pressure
Fitting
2
Air Shutoff Valve
Connect air hose with 3/4 in NPT fitting (not
supplied) to air shutoff valve.
Be sure valve is in open position when using air compressor.
The compressor runs and air pressure is
available whenever the engine is running
and the front panel Compressor switch is
moved to the On position (see Section 6-1).
Run engine at weld/power speed for maximum air compressor output. Compressor
output is reduced when engine is running at
idle speed.
The air compressor will not start if still under
pressure. If air compressor is turned off,
wait for air pressure to bleed off (about 20
seconds) before turning air compressor on
again.
Using the air compressor does not sig-
nificantly affect weld or generator power output.
OM-4409 Page 31
SECTION 6 − OPERATING THE WELDING GENERATOR
6-1. Controls (See Section 6-2)
10
11
14
15
4 6
5
3
7
16
9
12
1
2
8
13
17
803 229 / 236 974
OM-4409 Page 32
6-2. Description Of Controls (See Section 6-1)
Engine Starting Controls
1 Starting Aid Switch
Use switch to energize starting aid for cold
weather starting.
Push switch up for 60 seconds to operate the
starting aid (intake air heater) before cranking
engine (see starting instructions following).
2 Engine Control Switch
Use switch to start engine, select engine
speed, and stop engine.
In Run position, engine runs at weld/power
speed. In Auto position, engine runs at idle
speed with no generator power or weld load,
and weld/power speed with load applied.
The air compressor load does not affect engine speed. Run engine at weld/power speed
for maximum air compressor output.
To Start:
If engine does not start, let engine come
to a complete stop before attempting restart.
Above 32 F (0 C): turn Engine Control
switch to Start. Release Engine Control
switch when engine starts.
Below 32 F (0 C) using starting aid
switch:
Turn Engine Control switch to Auto position.
Push Starting Aid switch up for 60 seconds.
While still holding Starting Aid switch, turn Engine Control switch to Start. Release Engine
Control switch and Starting Aid switch when
engine starts.
To Stop: turn Engine Control switch to Off
position.
Engine/Compressor Gauges
3 Engine Fuel/Hour Gauge
Use gauge to monitor engine running time for
scheduling maintenance and to determine
cause of engine shutdowns.
Use gauge to check fuel level. Engine stops
if fuel level is low.
To check fuel level when engine is not running, turn Engine Control switch to Run or
Auto position.
See Section 6-5 for complete fuel/hour gauge
information.
4 Air Pressure Gauge
Use gauge to check compressor air pressure.
5 Engine Oil Pressure Gauge
Normal pressure is 30 − 60 psi (206 − 414
kPa). Engine stops if pressure is below 20 psi
(138 kPa).
6 Engine Temperature Gauge
Normal temperature is 212 - 239° F (100 115° C). Engine stops if temperature exceeds
270° F (132° C).
7 Battery Voltmeter
Use gauge to check battery voltage and monitor the engine charging system. The meter
should read about 14 volts dc when the engine is running, and about 12 volts dc when
the engine is stopped.
8 Air Compressor Hour Meter (Optional)
Use gauge to monitor compressor running
time for scheduling maintenance.
Weld Controls
9 Process/Contactor Switch
See Section 6-3 for Process/Contactor
switch information.
10 Ampere Range Switch
NOTICE − Do not switch under load.
Use switch to select weld amperage range.
Use all five ranges for Stick welding, and the
lowest four ranges for TIG welding. Read the
upper set of numbers at each range for Stick
welding and the lower set at each range for
TIG welding.
Use the highest range for MIG welding and for
cutting and gouging (CAC-A).
For most welding applications, use lowest
amperage range possible to help prevent arc
outages.
11 Voltage/Amperage Adjust Control
With Process/Contactor switch in any Stick or
TIG setting, use control to adjust amperage
within range selected by Ampere Range
switch. With Process/Contactor switch in any
MIG position, use control to adjust voltage.
With Panel/Remote Switch in Remote position, control limits the remote amperage in
TIG mode, but has no effect in Stick and MIG
modes.
Weld output would be about 263 A DC with
controls set as shown (50% of 125 to 400 A).
The numbers around the Voltage/Amper-
age Adjust control are for reference only
and do not represent an actual percentage value.
12 Panel/Remote Switch And Remote 14
Receptacle
Use switch to select front panel or remote
voltage/amperage control. For remote control, place switch in Remote position and connect remote control to Remote 14 receptacle
RC14 (see Sections 5-12 and 6-4).
13 Polarity/AC Selector Switch (Optional)
Or Output Selector Switch (Optional)
NOTICE − Do not switch under load.
Use Polarity/AC selector switch to select AC
or DC weld output and DC weld output polarity.
Use Output Selector switch to select AC
Weld, DC Weld, or battery charge output (see
Section 8-1).
Weld Meters
14 AC/DC Voltmeter (Optional)
Voltmeter displays voltage at the weld output
terminals, but not necessarily the welding arc
due to resistance of cable and connections.
15 AC/DC Ammeter (Optional)
Ammeter displays amperage output of the
unit.
Air Compressor Controls
16 Air Compressor Switch
Use switch to turn air compressor on and off.
Air pressure is present at the compressor air
shutoff valve whenever the compressor is
running. The compressor shuts off when the
engine stops. To use air, the compressor must
be turned on each time the engine is started.
The air compressor will not start if still under
pressure. If air compressor is turned off, wait
for air pressure to bleed off (about 20 seconds) before turning air compressor on again.
To extend clutch bearing life, cycle air
compressor off and on once every two
hours during periods of extended use.
17 Air Shutoff Valve
!
Air pressure is present at valve whenever Air Pressure Gauge (item 4) indicates air pressure.
Close valve to stop air flow when connecting
or changing tools or air hoses (see Section
5-13).
OM-4409 Page 33
6-3. Process/Contactor Switch
1
1
Process/Contactor Switch
!
Weld output terminals are energized when Process/Contactor
switch is in a Weld Terminals Always On position and the engine is running.
!
DC voltage is still present at the
weld terminals when Process/
Contactor switch is in the Remote On/Off Switch Required −
Stick position and the engine is
running.
Use switch to select weld process and
weld output on/off control (see table below and Section 6-4).
Place switch in Remote On/Off Switch
Required positions to turn weld output
on and off with a device connected to
the remote 14 receptacle.
Place switch in Weld Terminals Always
On positions for weld output to be on
whenever the engine is running.
Use Stick position for air carbon arc
(CAC-A) cutting and gouging.
When switch is in a Stick position, the
arc drive (dig) circuit provides additional amperage during low voltage (short
arc length conditions) to prevent “sticking” electrodes.
The arc drive (dig) circuit is disabled
when switch is in MIG or TIG positions.
The engine auto idle option does
not work in the Remote On/Off
Switch Required-TIG mode.
236 974
Process/Contactor Switch Settings
Switch Setting
Process
Output On/Off Control
Engine Auto Idle (Optional)
Remote On/Off Switch Required − TIG, HF Required
Or Scratch Start TIG
GTAW With HF Unit, Pulsing
Device, Or Remote Control
At Remote 14 Receptacle
Not Active
Remote On/Off Switch
Required − Stick
Stick (SMAW) With Remote On/Off
At Remote 14 Receptacle
Active
Remote On/Off Switch
Required − CV Feeder
Using Remote
MIG (GMAW)
At Remote 14 Receptacle
Active
Weld Terminals Always On −
Wire
MIG (GMAW)
Electrode Hot
Active
Weld Terminals Always On −
Stick
Stick (SMAW),
Air Carbon Arc (CAC-A) Cutting
And Gouging
Electrode Hot
Active
Weld Terminals Always On −
TIG, Scratch Start
TIG Scratch Start (GTAW)
Electrode Hot
Active
OM-4409 Page 34
6-4. Using Remote Voltage/Amperage Control
1
Remote 14 Receptacle RC14
Connect optional remote control to
RC14 (see Section 5-12).
1
803 231
In Example:
Process = Stick (Using Remote On/Off)
Range = 125 to 400 A DC
Min = 125 A DC
Max = 400 A DC
Example: Combination Remote Amperage Control (Stick)
Max (400 A DC)
Min (125 A DC)
Set
Panel/Remote
Switch
Set Remote
Process
Set Range
Control Not Used
In Remote On/Off
Switch Required −
Stick Mode
Adjust Optional Remote Control
In Example:
Process = TIG (Using Remote On/Off)
Range = 40 to 330 A DC
Percentage Of Range = 50%
Min = 40 A DC
Max = About 185 A DC (50% of 40 to 330)
Example: Combination Remote Amperage Control (TIG)
Max (185 A DC)
Min (40 A DC)
Set
Panel/Remote
Switch
Set Remote
Process
Set Range
Set Control
Adjust Optional Remote Control
0774 / Ref. 236 974 / 803 231
OM-4409 Page 35
6-5. Fuel/Hour Gauge Descriptions
OM-4409 Page 36
SECTION 7 − OPERATING AUXILIARY EQUIPMENT
7-1. Domestic Auxiliary Power Receptacles
1
120 V 20 A AC GFCI
Receptacle GFCI1
2
240 V 30 A AC Twistlock
Receptacle RC1
Receptacles supply 60 Hz singlephase power at weld/power speed.
1
3
2
If a ground fault is detected, GFCI
Reset button pops out and
receptacle does not work. Check
for faulty tools plugged in
receptacle. Press button to reset
GFCI1.
At least once a month, run en-
gine at weld/power speed and
press test button to verify GFCI
is working properly.
4
3
Supplementary Protector CB1
4
Supplementary Protector CB2
CB1 protects RC1 and the generator winding from overload. If CB1
opens, RC1 and GFCI1 do not
work. Place switch in On position to
reset.
CB2 protects GFCI1 from overload.
If CB2 opens, GFCI1 does not
work. Press button to reset.
If
a supplementary protector
continues to open, contact
Factory Authorized Service
Agent.
Generator
power is not affected by weld output.
Maximum output is 2.4 kVA/kW
from GFCI1 and 4 kVA/kW from
RC1. Maximum output from all receptacles is 4 kVA/kW.
EXAMPLE: If 13 A is drawn from
RC1, only 7 A is available at GFCI1:
(240 V x 13 A) + (120 V x 7 A) =
4.0 kVA/kW
191 624
OM-4409 Page 37
7-2. Connecting To Optional AC Power Plant
Do not weld while using optional ac
power plant.
1
Single-Phase Power Connection
Place Process/Contactor switch in
2
Weld Terminals Always On - Stick
position when using optional ac
power plant (see Section 6-3).
Single-Phase Generator Power
1
120/240 V 50 A Receptacle RC5
RC5 is connected to the optional ac
power plant and supplies 60 Hz singlephase power at weld/power speed.
Maximum output from RC5 is 12 kVA/
kW. Power available at RC5 is reduced
when welding.
2
Three-Phase Power Connection
!
Volts
Single
Phase
1
120/240
Three
Phase
3
240
Amps
50
48
KVA/KW
12
20
AC
Output
Close panel opening
if no connections are
made to power plant.
Frequency
Engine Speed
60 Hz
1850 RPM
Lead 42 connects to GROUND stud on
front of unit.
Jumper 42 is connected to 90 at factory.
93
Remove plug
before inserting
leads. Reinstall
bushing.
92
93
Stop engine.
!
Power and weld outputs are live
at the same time. Disconnect or
insulate unused cables.
Have qualified person install ac-
cording to circuit diagram and
Generator Power Guidelines (see
Section 16).
Remove power panel mounting
screws. Tilt panel forward.
Lead 93
Lead 92
90 5
Lead 91
3
6
6
Lead 42 (Circuit Grounding Lead)
7
Lead 90 (Neutral)
8
Isolated Neutral Terminal
9
Jumper Lead 42
10 Grounding Terminal
2
Jumper 42 is connected to lead 90 at
factory. Jumper 42 may be disconnected from neutral to meet applicable
electrical codes.
12
7
!
4
5
91
Three-Phase Generator Power
91 3
92
4
Rear Of Panel
Supplementary Protector CB7
Supplementary protector CB7 protects
single-phase receptacle RC5 and the
load wires from overload. If CB7
opens, all generator ac output stops
and the receptacle does not work.
Lead 42 connects to front panel
Ground stud.
10
11 User-Supplied Leads
12 Supplementary Protector CB7
User Terminals
11
!
9
8
Close
panel
opening if no
connections
are made to
power plant.
240V
1-Phase
120V
120V
Tools Needed:
240V
3-Phase
240V
240V
Ref. 197 399 / 802 332-B
OM-4409 Page 38
Connect user-supplied leads to terminals on CB7 and to the isolated neutral
terminal and grounding terminal as
necessary.
Supplementary protector CB7 pro-
tects single-phase receptacle RC5
and the load wires from overload.
If CB7 opens, all ac power plant
output stops and the receptacle
does not work.
Reinstall power panel.
7-3. Export Auxiliary Power Receptacles
4
3
European Receptacle
Australian Receptacle
1
2
5
South African Receptacle
6
238 127-A / 805 259-A
1
120V 15/20A AC Receptacle GFCI1
tacles is 4 kVA/kW.
Receptacles supply 60 Hz single-phase
power at weld/power speed.
EXAMPLE: If 13 A is drawn from RC1, only
7 A is available at GFCI1:
If a ground fault is detected, GFCI1 Reset
button pops out and receptacle does not
work. Check for faulty tools plugged into receptacle. Press button to reset GFCI1.
(240 V x 13 A) + (120 V x 7 A) =
4.0 kVA/kW
At least once a month, run engine at
CB2 protects GFCI1 from overload. If a circuit breaker opens, the receptacle does not
work. Press CB2 to reset breaker.
weld/power speed and press test button to verify GFCI is working properly.
Maximum output is 2.4 kVA/kW from GFCI1
and 4 kVa/kW from RC1.
Maximum combined output of all recep-
2
3
Circuit Breaker CB2
Earth Leakage Circuit Breaker
ELCB1
ELCB1 protects RC1 from Earth leakage
fault. If circuit breaker opens the receptacle
does not work. Place circuit breaker switch
in the On position to reset breaker.
At least once a month, press test but4
5
6
ton. If ELCB is working properly, power
will be disconnected. Reset breaker.
220V 16A AC European
Receptacle RC1
240 V 15 A AC Australian
Receptacle RC1
240 V 15 A AC South African
Receptacle RC1
If a circuit breaker continues to open,
contact Factory Authorized Service
Agent.
OM-4409 Page 39
SECTION 8 − OPERATING OPTIONAL BATTERY CHARGER
8-1. Battery Charge Controls
1
Output Selector Switch
NOTICE − Do not switch under load. Stop engine or set Process/Contactor switch to any
Remote position before switching.
Use switch to select weld or battery charge
output. Output automatically decreases (but
does not stop) when terminal voltage is 15 to
25 percent above required battery voltage.
1
Before connecting charging cables,
place
Output Selector switch in position matching voltage of battery being charged.
When done charging, stop engine or set Process/Contactor switch to any Remote On/Off
Switch Required position. Move Output Selector switch to AC Weld or DC Weld position.
803 231-A / 210 149-B
8-2. Determining Battery Charging Current
BATTERY CHARGING CURRENT (AMPS)
1
1
Battery Charging Current
Chart
Find battery cold crank amp (CCA)
rating on battery. Use CCA rating
on chart to find charge current setting for battery.
400
350
EXAMPLE: If battery CCA rating is
500, charging current from chart is
100 amperes.
300
250
Do not exceed charging current
found on chart. For longer battery
life, use lowest charge rate
possible.
200
150
100
50
0
0
500
1000
1500
BATTERY COLD CRANK AMP RATING (CCA)
OM-4409 Page 40
2000
142 975-B
8-3. Battery Charge Cable Connections
4
1
+
5
3
2
−
803 231-A / 210 156 / Ref. S-0714 / Ref. S-0756
!
Stop engine.
!
Do not charge or jump start a battery
which has loose terminals or one
showing damage such as a cracked
case or cover.
!
Have only qualified persons do battery charging work.
!
Keep cables away from moving
parts.
!
Do not use damaged cables.
!
Be sure charger output voltage
matches battery voltage.
!
Read BCI Battery Service Manual
before charging or jump starting.
Before
Use lugs of proper amperage capacity and
hole size for connecting to charge output
terminals.
connecting to battery, place
Output Selector switch in position
matching voltage of battery being
charged.
Install suitable connectors on remaining
ends of battery cables.
4
Battery Charge Positive (+) Output
Terminal
1
Battery
5
Battery Charge Negative (−) Output
Terminal
2
Battery Charging Cables
Connect
For battery charging, use less than 20 feet
(6.1 m) of AWG #1 or larger cable. For jump
starting, use less than 20 feet (6.1 m) of
AWG 2/0 or larger cable.
3
Terminal Lug
charging cables to battery
charge output terminals before connecting to battery terminals.
Connect Battery Charge Positive (+) cable
to battery positive (+) terminal, and battery
Charge Negative (−) cable to battery negative (−) terminal.
OM-4409 Page 41
8-4. Battery Charging Procedure
In Example:
Battery Voltage = 12 Volts
Battery CCA Rating = 500
Charge Current = 100 A (See Section 8-2)
Ampere Range Setting = 55 to 125 A
V/A Control Setting = Any Position
This battery charging procedure uses
the front panel controls to turn charging
output on and off.
Stop Engine.
Set Process/Contactor Switch To
Any Remote On/Off Switch Required
Position.
Set Output Selector Switch To
Voltage Of Battery Being
Charged (12 Or 24 Volt).
NOTICE − Do not switch under load.
−
Determine Charge Current From
Battery CCA Rating And Chart
(See Section 8-2).
Start Engine.
Set Ampere Range Switch To Lowest
Range That Exceeds Charge Current.
NOTICE − Do not switch under load.
Set Process/Contactor Switch
To Any Weld Terminals Always On
Position To Begin Charging.
To control battery charging output using a
remote device connected to the Remote
14 receptacle, keep Process/Contactor
switch in Remote On/Off Switch Required
position and use remote device to turn
charging output on and off.
OM-4409 Page 42
+
Connect Cables (Observe
Correct Polarity).
Charge 10 minutes. Check
Battery Voltage. Continue
Charging If Necessary.
8-5. Jump Starting Procedure
Charge battery for 10 minutes before
jump starting battery.
Stop Engine.
Set Process/Contactor Switch To
Any Remote On/Off Switch Required
Position.
Set Output Selector Switch To
Voltage Of Battery Being
Charged (12 Or 24 Volt).
NOTICE − Do not switch under load.
−
+
Set Ampere Range Switch To
300-Max Position.
Connect Cables (Observe
Correct Polarity).
NOTICE − Do not switch under load.
OR
Connect Remote
Control Device
(Momentary-On
Switch).
Press (close)
switch only while
cranking engine of
equipment being
started.
Start Engine.
Press (Close) Remote Momentary-On
Switch While Cranking Engine Of Equipment Being Jump Started. Release Switch
When Equipment Starts. Stop Welding
Generator And Disconnect Cables.
Stop Engine.
Disconnect
Cables.
OM-4409 Page 43
SECTION 9 − ENGINE/GENERATOR MAINTENANCE
9-1. Engine Maintenance Label
OM-4409 Page 44
9-2. Routine Engine/Generator Maintenance
See Section 10 for air compressor maintenance information.
!
Recycle engine
fluids.
= Check
= Change
= Clean
* To be done by Factory Authorized Service Agent
Every
8
Hours
Stop engine before maintaining.
See
Engine Manual and Maintenance Label
for important start-up, service, and storage
information. Service engine more often if
used in severe conditions.
= Replace
Reference
Section 5-9,
9-6
FUEL
WATER
Fuel/Water Separator
Fuel Level
Oil Level
Oil, Fuel Spills
Every
50
Hours
Weld Terminals
Every
100
Hours
Section 9-4
Battery Terminals
Air Cleaner Hoses
Every
250
Hours
Air Cleaner Element
Engine
Manual,
Section 9-5
1/2 in.
(13 mm)
Unreadable Labels
Fan Belt Tension
Cooling System
Weld Cables
Oil
Oil Filter
Spark Arrestor
Every
500
Hours
Every
1000
Hours
FUEL
OR
SLUDGE
Fuel Filter
Inside Unit
Valve Clearance*
Section 9-6,
9-3 and
Engine
Manual
Drain Sludge
Slip Rings*
Brushes*
Every
3000
Hours
Injectors*
Every
6000
Hours
or 5
Years
Engine Timing Belt
OM-4409 Page 45
9-3. Checking Generator Brushes
!
Stop engine and let cool.
1
Generator Brush
Remove brushes from brush holder.
Replace brushes if damaged or if brush
material is at or near minimum length.
Minimum Length:
5/8 in (16 mm)
New Length: 1-1/4 in (32 mm)
Replace
Damaged Brushes
1
Ref. 206 467
Notes
MATERIAL THICKNESS REFERENCE CHART
24 Gauge (.025 in)
22 Gauge (.031 in)
20 Gauge (.037 in)
18 Gauge (.050 in)
16 Gauge (.063 in)
14 Gauge (.078 in)
1/8 in (.125 in)
3/16 in (.188 in)
1/4 in (.25 in)
5/16 in (.313 in)
3/8 in (.375 in)
1/2 in (.5 in)
OM-4409 Page 46
9-4. Servicing Engine Air Cleaner
!
Stop engine.
NOTICE − Do not run engine without air
cleaner or with dirty element. Engine
damage caused by using a damaged element is not covered by the warranty.
1
Engine Air Cleaner
The air cleaner primary element can
be cleaned but the dirt holding capacity of the filter is reduced with each
cleaning. The chance of dirt reaching
the clean side of the filter while cleaning and the possibility of filter damage
makes cleaning a risk. Consider the
risk of unwarrantable equipment
damage when determining whether
to clean or replace the primary element.
If you decide to clean the primary element, we strongly recommend installing an optional safety element to provide additional engine protection.
Never clean a safety element. Replace the safety element after servicing the primary element three times.
1
2
3
4
Clean or replace primary element if dirty
(see note above before cleaning). Replace primary element if damaged. Replace primary element yearly or after six
cleanings.
5
2
Optional
6
Housing
3
Safety Element (Optional)
4
Primary Element
5
Dust Cap
6
Dust Ejector
To clean air filter:
Wipe off cap and housing. Remove cap
and dump out dust. Remove element(s).
Wipe dust from inside cap and housing
with damp cloth. Reinstall safety element
(if present). Reinstall cap.
NOTICE − Do not clean housing with air
hose.
Clean primary element with compressed
air only.
Air pressure must not exceed 100 psi
(690 kPa). Use 1/8 in (3 mm) nozzle and
keep nozzle at least 2 in (51 mm) from
inside of element. Replace primary element if it has holes or damaged gaskets.
Keep nozzle
2 in (51 mm)
from element.
Reinstall primary element and cap (dust
ejector down).
Blow
Inspect
aircleaner1 9/00 − 803 228 / 153 929-B / 153 585 / Ref. S-0698-B
OM-4409 Page 47
9-5. Inspecting/Cleaning Optional Spark Arrestor Muffler
!
Stop engine and let cool.
1
Spark Arrestor Muffler
2
Cleanout Plug
Remove plug and remove any dirt
covering cleanout hole.
Start engine and run at idle speed to
blow out cleanout hole. If nothing
blows out of hole, briefly cover end
of exhaust pipe with fireproof
material.
2
1
!
Stop engine and let cool.
Reinstall cleanout plug.
Tools Needed:
3/8 in
OM-4409 Page 48
803 228 / 803 230
9-6. Adjusting Engine Speed
!
Stop engine and let cool.
Engine speed is factory set and
should not require adjustment. After tuning engine, check engine no
load speed with a tachometer or frequency meter (see table for no load
speeds). If necessary, adjust speed
as follows:
Start engine and run until warm.
Turn Process/Contactor switch to
Weld Terminals Always On − Stick
position.
1
Throttle Rod
2
Locknut
Loosen locknuts. Place engine
control switch in Auto position.
Wait 15 seconds for throttle solenoid to energize and lower engine
speed to idle rpm.
Turn throttle rod to adjust idle
speed. Tighten locknuts.
3
Engine Speed Adjustment
Screw
4
Locknut
Place engine control switch in Run
position.
Loosen locknut. Turn screw to adjust weld/power speed. Tighten
locknut.
Do not set engine speed higher
than specified.
!
Stop engine.
Close door.
2
1
2
1850 rpm Max.
(61.6 Hz)
1235 rpm
(41.1 Hz)
3
4
Tools Needed:
3/8, 7/16 in
803 228 / 802 313-A
OM-4409 Page 49
9-7. Servicing Engine Fuel And Lubrication Systems
Tools Needed:
3
Right Side
1
4
5
7
6
2
!
!
Stop engine and let cool.
After servicing, start engine and
check for fuel leaks. Stop engine,
tighten connections as necessary,
and wipe up spilled fuel.
1 Oil Filter
2 Oil Drain Hose And Valve
3 Oil Fill Cap
4 Primary Fuel Filter (Fuel/Water
Separator)
5 Petcock
6 Secondary Fuel Filter
7 Fuel Tank Sludge Drain Valve
To change oil and filter:
The engine oil drain
and compressor oil
drain hoses are located together in the
OM-4409 Page 50
base. Be sure to select the correct hose
when draining engine oil.
Route engine oil drain hose through hole in
base. See engine manual and engine maintenance label for oil specifications.
To drain water from fuel system:
To replace secondary fuel filter:
See engine manual.
Close doors.
To drain sludge from fuel tank:
!
Open primary fuel filter petcock and drain
water into metal container. Close petcock
when water-free fuel flows.
To replace primary fuel filter:
Turn filter counterclockwise. Remove filter.
Apply thin coat of fuel to gasket on new filter.
Fill filter with fuel. Install filter and turn clockwise until tight. Bleed air from fuel system
according to engine manual.
Inspect fuel lines, and replace if cracked or
worn.
!
803 228
Beware of fire. Do not smoke and
keep sparks and flames away from
drained fuel. Dispose of drained fuel
in an environmentally-safe manner.
Do not leave unit unattended while
draining fuel tank.
Properly lift unit and secure in a level
position. Use adequate blocks or
stands to support unit while draining fuel tank.
Attach 1/2 ID hose to drain valve. Put metal
container under drain, and use screwdriver
to open sludge drain valve. Close valve
when sludge has drained. Remove hose.
9-8. Engine/Generator Overload Protection
!
Stop engine.
When a supplementary protector, cir-
cuit breaker or fuse opens, it usually
indicates a more serious problem exists. Contact Factory Authorized Service Agent.
See Section 10-4 for air compressor
overload protection.
1
2
Fuse F1
Fuse F2
F1 and F2 protect the stator exciter winding from overload. If F1 opens, weld and
generator power is low or stops entirely. If
F2 opens, weld output is low or stops entirely. 4 kVA/kW generator power is still
available.
3
4
5
2
1
Circuit Breaker CB4 (Not Shown)
Supplementary Protector CB5
Supplementary Protector CB6
6
Circuit Breaker CB10 (Not Shown)
7
Supplementary Protector CB11
8
Supplementary Protector CB12
9
Supplementary Protector CB13
10 Circuit Breaker CB14
(Not Shown)
11 Circuit Breaker CB16
(Not Shown)
9
8
7
4
5
CB4 protects the welding arc drive (dig)
circuit. If CB4 opens, electrode may stick
to the workpiece more frequently during
low voltage (short arc length) conditions.
CB4 automatically resets when the fault is
corrected.
CB5 protects the 24 volt ac output to remote receptacle RC14, and 24 volt output
to field current regulator board PC1. If
CB5 opens, weld output and 24 volt output
to RC14 stops. On units with optional
power plant, power at receptacle RC5
also stops if CB5 opens.
CB6 protects the 115 volt ac output to remote receptacle RC14. If CB6 opens, 115
volt output to RC14 stops.
CB10 protects the engine battery circuit.
If CB10 opens, the engine will not crank.
CB10 automatically resets when the fault
is corrected.
CB11 protects the engine wiring harness.
If CB11 opens, weld output stops (generator power is still available).
CB12 protects the field flashing circuit. If
CB12 opens, the generator may not excite at start-up and weld and generator
power output may not be available.
CB13 protects the engine shutdown circuit. If CB13 opens, the engine cranks but
does not start.
Press button to reset.
CB14 protects the throttle solenoid. If
CB14 opens, the engine will not run at idle
speed. CB14 automatically resets when
the fault is corrected.
CB16 protects the glow plug circuit. If
CB16 opens, the glow plug will not operate. CB16 automatically resets when the
fault is corrected.
803 229
OM-4409 Page 51
SECTION 10 − AIR COMPRESSOR MAINTENANCE
Use only genuine Ingersoll Rand compressor oil and filters to maintain 3-year warranty on air compressor. The air compressor warranty will be
reduced to 2 years if non-Ingersoll Rand oil and filters are used
The air compressor normally requires service at the intervals listed in the maintenance schedule if used in a clean, dry environment. The compressor will require service more often if used in dirty, humid conditions.
10-1. Air Compressor Maintenance Label
OM-4409 Page 52
10-2. Routine Air Compressor Maintenance
See Section 9 for engine/generator maintenance information.
!
Recycle air
compressor
fluids.
= Check
= Change
= Clean
* To be done by Factory Authorized Service Agent
Stop engine before maintaining.
See
Compressor Maintenance Label for important start-up, service, and storage information. Service air compressor more often
if used in severe conditions.
= Replace
Reference
Every
8
Hours
Section 5-9
Spills
Oil Level
Every
100
Hours
Air Cleaner Hoses
Every
250
Hours
Section
10-3
Unreadable Labels
Belt Tension
Cooling System
Air Filter Element
Worn or Damaged Air/Oil
Hoses
Every
500
Hours
Section
10-5
Oil
Every
1000
Hours
Oil Filter
Section
10-5
Air/Oil Separator
OM-4409 Page 53
10-3. Servicing Compressor Air Cleaner
!
Stop engine.
NOTICE − Do not run air compressor
without air cleaner or with dirty element.
Compressor damage caused by using a
damaged element is not covered by the
warranty.
1
Compressor Air Cleaner
Remove engine
air cleaner cover
and element to access compressor
air cleaner (see Section 9-4)
The air cleaner primary element can
be cleaned but the dirt holding capacity of the filter is reduced with each
cleaning. The chance of dirt reaching
the clean side of the filter while cleaning and the possibility of filter damage
makes cleaning a risk. Consider the
risk of unwarrantable equipment
damage when determining whether
to clean or replace the primary element.
1
2
3
4
If you decide to clean the primary element, we strongly recommend installing an optional safety element to provide additional air compressor
protection. Never clean a safety element. Replace the safety element after servicing the primary element
three times.
5
Clean or replace primary element if dirty
(see note above before cleaning). Replace primary element if damaged. Replace primary element yearly or after six
cleanings.
6
2
Housing
3
Safety Element
4
Primary Element
5
Cover
6
Dust Ejector
To clean air filter:
Wipe off cover and housing. Remove
cover and dump out dust. Remove element(s). Wipe dust from inside cover and
housing with damp cloth. Reinstall safety
element (if present). Reinstall cover.
NOTICE − Do not clean housing with air
hose.
Keep nozzle
2 in (51 mm)
from element.
Clean primary element with compressed
air only.
Air pressure must not exceed 100 psi
(690 kPa). Use 1/8 in (3 mm) nozzle and
keep nozzle at least 2 in (51 mm) from
inside of element. Replace primary element if it has holes or damaged gaskets.
Reinstall primary element and cover
(dust ejector down).
Blow
Inspect
aircleaner1 9/02* − 803 228 / 153 929-B / 153 585 / Ref. S-0698-B
OM-4409 Page 54
10-4. Compressor Overload Protection
!
Stop engine.
When
a circuit breaker or fuse
opens, it usually indicates a more
serious problem exists. Contact
Factory Authorized Service Agent.
See Section 9-8 for engine/generator overload protection.
1
Circuit Breaker CB15
Circuit breaker CB15 protects the air
compressor clutch. If CB15 opens, the
compressor does not run and air output
stops.
Press button to reset breaker.
1
803 228 / 803 229
OM-4409 Page 55
10-5. Servicing Air Compressor
Tools Needed:
7/8, 15/16 in
4
5
Too
High
Full
Right Side
1
Too
Low
6
3
2
803 228
!
1
2
3
Stop engine and let cool. Wait 20 seconds for system pressure to drop before changing oil.
Air Compressor Oil Filter
Air Compressor Air/Oil Separator
Air Compressor Oil Drain Hose
w/Removable Cap
4
Air Compressor Oil Fill Cap
5
Air Compressor Oil Level Indicator (On
Tank)
6
Oil Scavenge Tube
OM-4409 Page 56
To change compressor oil and filter:
The engine oil drain
and compressor oil
drain hoses are located together in the
base. Be sure to select the correct hose
when draining compressor oil.
Be sure o-rings at oil drain and oil fill fit-
tings are in place before reinstalling caps.
Drain compressor oil while compressor is still
warm.
Route compressor oil drain hose through hole
in base. Remove compressor oil fill cap. Remove cap from oil drain hose and drain oil into
a suitable container. Reinstall oil drain hose
cap. Tighten cap with wrench.
Remove filter by turning filter counterclockwise. Remove filter. Apply thin coat of oil to
gasket on new filter. Install new filter and turn
clockwise until tight.
Add recommended oil until oil level indicator
shows system is full (see compressor maintenance label for oil specifications). Reinstall oil
fill cap. Tighten cap with wrench.
To replace air/oil separator:
Loosen nut securing tube on separator base.
Lift oil scavenge tube from separator. Turn filter counterclockwise. Remove filter.
Apply thin coat of oil to gasket on new filter.
Install filter and turn clockwise. Reinstall oil
scavenge tube.
Start engine, run air compressor, and check
for oil leaks.
!
Stop engine.
10-6. Adjusting Compressor Air Pressure
Check compressor air pressure using
air pressure gauge known to be accurate. If necessary, adjust air pressure
as follows:
1
Tools Needed:
5/16, 3/8 in
Screw
Loosen jam nut securing screw. Turn
screw clockwise (increase pressure)
or counterclockwise (decrease) until
pressure is 125 psi (862 kPa).
Maximum weld output is reduced
if compressor air pressure is set
above 125 psi (862 kPa).
Tighten nut.
2
Pressure Relief Valve
Pressure relief valve opens and releases pressure at 150 psi (1034
kPa). The pressure relief valve is not
adjustable.
1
2
803 228
OM-4409 Page 57
SECTION 11 − TROUBLESHOOTING
11-1. Troubleshooting Tables
A. Welding
Trouble
Remedy
No weld output; generator power output Place Process/Contactor switch in a Weld Terminals Always On position, or place switch in a Remote
okay at ac receptacles.
On/Off Switch Required position and connect remote contactor to Remote 14 receptacle RC14 (see Sections 5-12 and 6-1).
Check position of Ampere Range switch.
Check position of optional Output Selector switch (see Section 8-1).
Reset supplementary protector CB11 (see Section 9-8).
Reset supplementary protector CB5 (see Section 9-8). Check for faulty remote device connected to
RC14.
Check and secure connections to Remote 14 receptacle RC14 (see Section 5-12).
Have Factory Authorized Service Agent check connector board PC6 and connections.
Check fuse F2, and replace if open (see Section 9-8). Have Factory Authorized Service Agent check
brushes and slip rings, field excitation circuit, field current regulator board PC1, and the rotor.
No weld output or generator power Disconnect equipment from generator power receptacles during start-up.
output.
Check fuses F1 and F2, and replace if open (see Section 9-8). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, field current regulator board PC1, and the rotor.
Reset supplementary protector CB12 (see Section 9-8).
Have Factory Authorized Service Agent check brushes and slip rings, and field excitation circuit.
Erratic weld output.
Check and tighten connections inside and outside unit.
Be sure connection to work piece is clean and tight.
Use dry, properly stored electrodes.
Remove excessive coils from weld cables.
High weld output.
Check position of Ampere Range switch and Voltage/Amperage Adjust control.
Check engine weld/power speed, and adjust if necessary (see Section 9-6).
Have Factory Authorized Service Agent check field current regulator board PC1.
Voltage/Amperage control does not Place Ampere Range switch in lower range. Voltage/Amperage control does not work with Ampere
work when welding in Stick mode.
Range switch in highest range.
Low weld output.
Check engine weld/power speed, and adjust if necessary (see Section 9-6).
Check fuses F1 and F2, and replace if open (see Section 9-8). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, field current regulator board PC1, and the rotor.
Electrode sticks to the workpiece more Circuit breaker CB4 may be open. CB4 automatically resets when the fault is corrected (see Section 9-8).
frequently during low voltage (short arc Have Factory Authorized Service Agent check transformer T1 and integrated rectifiers SR4 and SR5.
length) conditions.
Have Factory Authorized Service Agent check optional battery charging relay CR7.
Low open-circuit voltage.
Check engine weld/power speed, and adjust if necessary.
No remote fine amperage or voltage Place Panel/Remote Switch in Remote position.
control.
Check and secure connections to Remote 14 receptacle RC14 (see Section 5-12).
Repair or replace remote control device.
OM-4409 Page 58
Trouble
Remedy
Constant speed wire feeder does not Reset supplementary protector(s) CB5 and CB13 (see Section 9-8).
work.
Check and secure connections to Remote 14 receptacle RC14 (see Section 5-12).
Repair or replace wire feeder.
Low CV weld output.
Set Ampere Range switch to highest range.
Min or max CV weld output only.
Check position of Voltage/Amperage Adjust control and Panel/Remote Switch.
Repair or replace remote control device.
Have Factory Authorized Service Agent check field current regulator board PC1.
B. Standard Generator Power
Trouble
Remedy
No generator power output at ac recep- Reset receptacle supplementary protectors.
tacles; weld output okay.
No generator power or weld output.
Disconnect equipment from generator power receptacles during start-up.
Check fuses F1 and F2, and replace if open (see Section 9-8). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, diode/capacitor board D1/C1, and the rotor.
Reset supplementary protector CB12. Have Factory Authorized Service Agent check field current regulator board PC1 (see Section 10-4).
Have Factory Authorized Service Agent check brushes and slip rings, and field excitation circuit.
High output
receptacles.
at
generator
power Check engine weld/power speed, and adjust if necessary (see Section 9-6).
Have Factory Authorized Service Agent adjust field current resistor R3.
Low output
receptacles.
at
generator
power Check engine weld/power speed, and adjust if necessary (see Section 9-6).
Check fuse F1, and replace if open (see Section 9-8). Have Factory Authorized Service Agent check integrated rectifier SR1, resistor R3, and capacitor C9.
C. Optional AC Power Plant
Trouble
No or low output at optional ac power
plant/receptacle RC5.
Remedy
Place Process/Contactor switch in Weld Terminals Always On - Stick position (see Section 6-3).
Reset supplementary protector CB7 (see Section 7-2).
Reset supplementary protector CB5 (see Section 9-8).
Check engine weld/power speed, and adjust if necessary (see Section 9-6).
Have Factory Authorized Service Agent check brushes and slip rings, and field current regulator board
PC1.
High output at optional ac power plant/
receptacle RC5.
Check engine weld/power speed, and adjust if necessary (see Section 9-6).
Have Factory Authorized Service Agent check field current regulator board PC1.
Erratic output at optional ac power plant/ Have Factory Authorized Service Agent check brushes and slip rings, and field current regulator board
receptacle RC5.
PC1.
OM-4409 Page 59
D. Engine
Trouble
Engine will not crank.
Remedy
Check battery, and replace if necessary.
Check battery connections and tighten if necessary.
Circuit breaker CB10 may be open. CB10 automatically resets when fault is corrected (see Section 9-8).
Have Factory Authorized Service Agent check engine wiring harness and components.
Check engine wiring harness plug connections.
Turn optional battery disconnect switch to On position (see Section 5-8).
Have Factory Authorized Service Agent check Engine Control switch S1, control relay CR1, and diode/
capacitor board D8/C8.
Engine cranks but does not start.
Check fuel level. Optional low fuel shutdown stops engine if fuel level is low.
Reset supplementary protector CB13 (see Section 10-4 ). Have Factory Authorized Service Agent check
engine wiring harness and components.
Check battery and replace if necessary. Check engine charging system according to engine manual.
Have Factory Authorized Service Agent check fuel/hour gauge, control relay CR5, fuel pump, and fuel
solenoid FS1.
Air in fuel system. See engine manual.
Engine starts, but stops when Engine Check oil level. Automatic shutdown system stops engine if oil pressure is too low or engine temperature
Control switch is released.
is too high (see Section 5-9).
Have Factory Authorized Service Agent check fuel/hour gauge, and control relay CR5.
Engine hard to start in cold weather.
Use starting aid switch (see Section 6-1). If Starting Aid switch does not work have Factory Authorized
Service Agent check Engine Control switch S2, control relay CR8, and circuit breaker CB16.
Keep battery in good condition. Store battery in warm area off cold surface.
Use fuel formulated for cold weather (diesel fuel can gel in cold weather). Contact local fuel supplier for
fuel information.
Use correct grade oil for cold weather (see Section 9-1 ).
Engine suddenly stops.
Check fuel level. Optional low fuel shutdown stops engine if fuel level is low.
Check oil level. Automatic shutdown system stops engine if oil pressure is too low or engine temperature
is too high (see Section 5-9).
Have Factory Authorized Service Agent check fuel/hour gauge, control relay CR5, fuel pump, and fuel
solenoid FS1.
See engine manual.
Engine slowly stopped and cannot be
restarted.
Check fuel level.
Check engine air and fuel filters (see Sections 9-4 and 9-7).
See engine manual.
Battery discharges between uses.
Turn Engine Control switch S1 off when unit is not running.
Clean top of battery with baking soda and water solution; rinse with clear water.
Recharge or replace battery if necessary.
Periodically recharge battery (approximately every 3 months).
Engine idles, but does not come up to
weld speed.
Have Factory Authorized Service Agent check idle module PC7.
Check for obstructed throttle solenoid.
OM-4409 Page 60
Trouble
Engine does not run at idle speed.
Remedy
Turn Process/Contactor switch to any position but Remote On/Off Switch Required-TIG.
Check for obstructed throttle solenoid.
Allow circuit breaker CB14 to reset. Have Factory Authorized Service Agent check throttle solenoid TS1
and linkage (see Section 9-8).
Have Factory Authorized Service Agent check idle module PC7, control relays CR3 and CR6, and current
transformer CT1.
Engine uses oil during run-in period; Dry engine (see Section 14).
wetstacking occurs.
E. Air Compressor
Trouble
Remedy
Air compressor does not operate; no air Place Air Compressor switch in On position. The air compressor will not start if still under pressure. If
pressure at air shutoff valve.
compressor is turned off, wait for air pressure to bleed off (about 20 seconds) before turning compressor
on again.
Reset supplementary protector CB15 (see Section 10-4).
Check compressor belt tension. Be sure correct belt is used and is properly installed.
Have Factory Authorized Service Agent check Air Compressor switch S10, control relay CR10, air pressure switch S11, temperature switch S12, compressor control circuit, and air compressor clutch.
Air compressor stops after short period Check compressor oil level (see Section 5-9). Automatic shutdown stops compressor if compressor temof operation.
perature is too high.
Clean debris from radiator. Automatic shutdown stops compressor if compressor temperature is too high.
Low air pressure.
Check for leaks in air lines and hoses.
Adjust compressor air pressure (see Section 10-6).
Check air compressor air cleaner (see Section 10-3).
Have Factory Authorized Service Agent check compressor for rated output.
High air pressure.
Adjust compressor air pressure (see Section 10-6).
Be sure control line is connected at regulator valve and inlet valve.
Pneumatic tools freeze up because of Install optional air dryer/filter kit (Part No. 195 117).
moisture in compressed air.
Oil in air from compressor.
Check compressor oil level (see Section 5-9). If oil level is too high, system becomes saturated with oil.
Change compressor air/oil separator (see Section 10-5).
Check connections of control lines (see air compressor circuit diagram in Section 12).
Have Factory Authorized Service Agent check for blocked separator scavenge check valve/filter orifice.
Oil in compressor air cleaner.
Have Factory Authorized Service Agent verify compressor inlet valve is operating properly.
F. Optional Battery Charging
Trouble
No battery charge output; weld output
okay.
Remedy
Place Output Selector switch in 12 Volt Charge or 24 Volt Charge position.
Check and tighten battery connections if necessary.
Turn on remote control device or turn Process/Contactor switch to any Weld Terminals Always On
position (see Section 6-3).
No battery charge or weld output.
Disconnect equipment from generator power receptacles during start-up.
Check fuses F1 and F2, and replace if open (see Section 9-8). Have Factory Authorized Service Agent
check integrated rectifier SR1, capacitor C9, field current regulator board PC1, and the rotor.
Reset supplementary protector CB12 (see Section 9-8).
Have Factory Authorized Service Agent check brushes and slip rings, field current regulator board PC1,
and field excitation circuit.
OM-4409 Page 61
SECTION 12 − CIRCUIT DIAGRAM
Figure 12-1. Circuit Diagram For Welding Generator
OM-4409 Page 62
238 931-A
OM-4409 Page 63
SECTION 13 − AIR COMPRESSOR DIAGRAM
209 059-A
Figure 13-1. Circuit Diagram For Air Compressor
OM-4409 Page 64
SECTION 14 − RUN-IN PROCEDURE
run_in1 2007−04
14-1. Wetstacking
NOTICE − Do not perform run-in
procedure at less than 20 volts
weld output and do not exceed duty
cycle or equipment damage may
occur.
1
2
1
Welding Generator
Run diesel engines near rated voltage and current during run-in period
to properly seat piston rings and
prevent wetstacking. See nameplate, rating label, or specifications
section in this manual to find rated
voltage and current.
NOTICE − Do not idle engine longer
than necessary. Piston rings seat
faster if engine runs at weld/power
rpm, and the welding generator is
kept loaded during run-in.
2
Engine Exhaust Pipe
Wetstacking is unburned fuel and
oil in the exhaust pipe and occurs
during run-in if the engine is run too
long at light load or idle rpm.
If exhaust pipe is coated with a wet,
black, tar-like substance, dry the
engine using one of the following
run-in procedures.
See the engine manual for additional engine run-in information.
OM-4409 Page 65
14-2. Run-In Procedure Using Load Bank
4
2
1
!
Stop engine.
!
Do not touch hot exhaust
pipe, engine parts, or load
bank/grid.
!
Keep exhaust and pipe away
from flammables.
NOTICE − Do not perform run-in
procedure at less than 20 volts weld
output and do not exceed duty
cycle or equipment damage may
occur.
1 Load Bank
Turn all load bank switches Off. If
needed, connect load bank to 115
volts ac wall receptacle or generator auxiliary power receptacle.
2 Welding Generator
Place A/V range switch in maximum position, A/V control in minimum position, and Output Selector
switch (if present) in either DC
position.
3 Weld Cables
Connect load bank to generator
weld output terminals using proper
size weld cables with correct
connectors. Observe
correct
polarity.
3
Start engine and run for several
minutes.
Set load bank switches and then
adjust generator A/V control so
load equals rated voltage and
current of generator (see nameplate, rating label, or the specifications section in this manual).
Check generator and load bank
meters after first five minutes then
every fifteen minutes to be sure
generator is loaded properly.
NOTICE − Check oil level frequently during run-in; add oil if needed.
It is recommended to run the welding generator for two hours minimum and up to four hours under
load. Place A/V control in minimum
position, then turn off load bank to
remove load. Run engine several
minutes at no load.
!
Stop engine and let cool.
4 Engine Exhaust Pipe
Repeat procedure if wetstacking is
present.
S-0683
OM-4409 Page 66
14-3. Run-In Procedure Using Resistance Grid
6
2
!
Stop engine.
!
Do not touch hot exhaust
pipe, engine parts, or load
bank/grid.
!
Keep exhaust and pipe away
from flammables.
NOTICE − Do not perform run-in
procedure at less than 20 volts weld
output and do not exceed duty
cycle or equipment damage may
occur.
1
1 Resistance Grid
Use grid sized for generator rated
output.
Turn Off grid.
2 Welding Generator
Place A/V range switch in maximum position, A/V control in minimum position, and Output Selector
switch (if present) in either DC
position.
3 Weld Cables
Connect grid to generator weld
output terminals using proper size
weld cables with correct connectors (polarity is not important).
4
3
5
Voltmeter
5 Clamp-On Ammeter
Connect voltmeter and ammeter as
shown, if not provided on generator.
Start engine and run for several
minutes.
Set grid switches and then adjust generator A/V control so
load equals rated voltage and
current of the generator (see
nameplate, rating label, or the
specifications section in this
manual).
4
+
Check generator and meters after
first five minutes then every fifteen
minutes to be sure generator is
loaded properly.
NOTICE − Check oil level frequently during run-in; add oil if needed.
It is recommended to run the welding generator for two hours minimum and up to four hours under
load. Place A/V control in minimum
position, then shut down grid to
remove load. Run engine several
minutes at no load.
!
Stop engine and let cool.
6 Engine Exhaust Pipe
Repeat procedure if wetstacking is
present.
S-0684
OM-4409 Page 67
SECTION 15 − AIR COMPRESSOR TABLES
15-1. Flow Of Free Air (CFM) Through Orifices Of Various Diameters
Orifice Diameter (in) And Free Air Flow (CFM)
Gauge Pressure (psi)
1/64
1/32
3/64
1/16
3/32
1/8
3/16
1/4
1
0.027
0.107
0.242
0.430
0.97
1.72
3.86
6.85
2
0.038
0.153
0.342
0.607
1.36
2.43
5.42
9.74
3
0.046
0.188
0.471
0.750
1.68
2.98
6.71
11.9
5
0.059
0.242
0.545
0.965
2.18
3.86
8.71
15.4
10
0.084
0.342
0.77
1.36
3.08
5.45
12.3
21.8
15
0.103
0.418
0.94
1.67
3.75
6.65
15.0
26.7
20
0.119
0.485
1.07
1.93
4.25
7.7
17.1
30.8
25
0.133
0.54
1.21
2.16
4.75
8.6
19.4
34.5
30
0.156
0.632
1.40
2.52
5.6
10.0
22.5
40.0
35
0.173
0.71
1.56
2.80
6.2
11.2
25.0
44.7
40
0.19
0.77
1.71
3.07
6.8
12.3
27.3
49.1
45
0.208
0.843
1.9
3.36
7.6
13.4
30.3
53.8
50
0.225
9.14
2.05
3.64
8.2
14.5
32.8
58.2
60
0.26
1.05
2.35
4.2
9.4
16.8
37.5
67.0
70
0.295
1.19
2.68
4.76
10.7
19.0
43.0
76.0
80
0.33
1.33
2.97
5.32
11.9
21.2
47.5
85.0
90
0.364
1.47
3.28
5.87
13.1
23.5
52.5
94.0
100
0.40
1.61
3.66
6.45
14.5
25.8
58.3
103.0
110
0.43
1.76
3.95
7.00
15.7
28.0
63.0
112.0
120
0.47
1.90
4.27
7.58
17.0
30.2
68.0
121.0
130
0.50
2.04
4.57
8.13
18.2
32.4
73.0
130.0
140
0.54
2.17
4.87
8.68
19.5
34.5
78.0
138.0
150
0.57
2.33
5.2
9.20
20.7
36.7
83.0
147.0
175
0.66
2.65
5.94
10.6
23.8
42.1
95.0
169.0
200
0.76
3.07
6.90
12.2
27.5
48.7
110.0
195.0
OM-4409 Page 68
15-2. Approximate Air Consumption (Cubic Feet) To Operate Pneumatic Equipment At
70-90 P.S.I.G.
MISCELLANEOUS
PORTABLE
TOOLS
Percent Use Factor And
Compressed Air Consumption (CF)
Percent Use Factor And
Compressed Air Consumption (CF)
1 min
MISCELLANEOUS
PORTABLE
TOOLS
8.75
25
Burring Tool, Large
3.6
6.0
8.4
24
8.75
12.25
35
Rammers, Small
3.9
3.25
9.1
13
1.8
3.0
4.2
12
Rammers, Medium
5.1
8.5
11.9
34
Screwdriver,
#6 to 5/16” Screw
3.6
6.0
8.4
24
Rammers, Large
6.0
10.0
14.0
40
Tapper, to 3/8”
3.0
5.0
7.0
20
Backfill Tamper
3.75
6.25
8.75
25
Nutsetters, to 3/8”
3.6
6.0
8.4
24
Compression Riveter
Nutsetters, to 3/4”
4.5
7.5
10.5
30
Air Motor,
1 Horsepower
3.75
6.3
8.75
25
Impact Wrench, 1/4”
2.25
3.75
5.3
15
Air Motor,
2 Horsepower
7.5
12.5
17.5
50
Impact Wrench, 3/8”
3.0
5.0
7.0
20
Impact Wrench, 5/8”
4.5
7.5
10.5
30
Air Motor,
3 Horsepower
11.25
18.75
26.3
75
Impact Wrench, 3/4”
5.25
8.75
12.25
35
Paint Spray Gun
(Production)
3.0
5.00
7.00
20
Impact Wrench, 1”
6.75
11.25
15.75
45
,HAMMERS
Impact Wrench, 1-1/4”
8.25
13.75
19.2
55
Scaling Hammer
1.3
3.0
4.2
12
Die Grinder, Small
Die Grinder, Medium
2.25
3.6
3.75
6.0
5.3
8.4
15
24
Chipping Hammer
4.5
7.5
10.5
30
Horizontal Grinder, 2”
3.0
5.0
7.0
20
Riveting Hammer,
Light
2.25
3.75
5.25
15
Horizontal Grinder, 4”
9.0
15.0
21.0
60
Horizontal Grinder, 6”
9.0
15.0
21.0
60
Riveting Hammer,
Heavy
4.5
7.5
10.5
30
Horizontal Grinder, 8”
12.0
20.0
28.0
80
Circular, 8”
6.75
11.25
15.75
45
Circular, 12”
9.75
16.25
23.8
65
5.25
8.75
12.25
35
Chain, Lightweight
4.20
7.0
9.8
28
9.0
15.0
21.0
60
Chain, Heavy Duty
13.1
21.8
30.5
87
Vertical Grinders and
Sanders, 9” Pad
10.5
17.5
24.5
70
Burring Toll, Small
2.25
3.75
5.3
15
9 sec
15 sec
21 sec
Drill, 1/18” to 3/8”
3.75
6.25
Drill, 3/8” to 5/16”
5.25
Screwdriver,
#2 to #6 Screw
Vertical Grinders and
Sanders, 5” Pad
Vertical Grinders and
Sanders, 7” Pad
9 sec
15 sec
21 sec
1 min
0.2 cu. ft. per cycle
SAWS
Always check with tool manufacturers for actual air consumption of tools being used. The above is based on averages and should not be
considered accurate for any particular make of tool.
Above tools are rated based upon typical “on-load” performance characteristics.
For other values, adjust the C.F. air consumption on a proportional basis.
The cubic feet (C.F.) air consumption for 1 minute may also be expressed as air consumption in cubic feet per minute (C.F.M.)
OM-4409 Page 69
SECTION 16 − GENERATOR POWER GUIDELINES
The views in this section are intended to be representative of all engine-driven welding generators. Your unit may differ from those shown.
16-1. Selecting Equipment
1
2
3
Generator Power Receptacles
− Neutral Bonded To Frame
3-Prong Plug From Case
Grounded Equipment
2-Prong Plug From Double
Insulated Equipment
Be sure equipment has double
insulated symbol and/or wording on it.
1
!
2
Do not use 2-prong plug unless equipment is double insulated.
3
OR
gen_pwr 2008−01 − ST-800 577
16-2. Grounding Generator To Truck Or Trailer Frame
!
Always ground generator
frame to vehicle frame to prevent electric shock and static
electricity hazards.
!
Also see AWS Safety &
Health Fact Sheet No. 29,
Grounding of Portable And
Vehicle Mounted Welding
Generators.
1
Equipment Grounding
Terminal (On Front Panel)
Grounding Cable (Not
Supplied)
Metal Vehicle Frame
2
3
1
2
Connect cable from equipment
ground terminal to metal vehicle
frame. Use #10 AWG or larger
insulated copper wire.
Electrically
bond generator
frame to vehicle frame by metal-to-metal contact.
GND/PE
!
Bed liners, shipping skids,
and some running gear insulate the welding generator
from the vehicle frame. Always connect a ground wire
from the generator equipment grounding terminal to
bare metal on the vehicle
frame as shown.
!
If unit does not have GFCI receptacles, use GFCI-protected extension cord.
3
800 652-D
OM-4409 Page 70
16-3. Grounding When Supplying Building Systems
1
2
1
2
Use #10 AWG or larger insulated
copper wire.
3
GND/PE
Equipment Grounding
Terminal
Grounding Cable
Ground Device
Use ground device as stated in
electrical codes.
2
3
!
Ground generator to system
earth ground if supplying
power to a premises (home,
shop, farm) wiring system.
!
Also see AWS Safety &
Health Fact Sheet No. 29,
Grounding of Portable And
Vehicle Mounted Welding
Generators.
ST-800 576-B
16-4. How Much Power Does Equipment Require?
1
Resistive Load
A light bulb is a resistive load and
requires a constant amount of power.
2
3
2
1
Non-Resistive Load
Equipment with a motor is a non-resistive load and requires approximately six times more power while
starting the motor than when running
(see Section 16-8).
VOLTS 115
AMPS 4.5
Hz
60
3
Rating Data
Rating shows volts and amperes, or
watts required to run equipment.
Amperes x Volts = Watts
Example 1: If a drill uses 4.5 amperes at 115 volts, calculate its running power requirement in watts.
3
4.5 A x 115 V = 520 W
The load applied by the drill is 520
watts.
Example 2: If three 200 watt flood
lamps are used with the drill from Example 1, add the individual loads to
calculate total load.
(3 x 200W) + 520 W = 1120 W
The total load applied by the three
flood lamps and drill is 1120 watts.
S-0623
OM-4409 Page 71
16-5. Approximate Power Requirements For Industrial Motors
Industrial Motors
Split Phase
Capacitor Start-Induction Run
Capacitor Start-Capacitor Run
Fan Duty
Rating
Starting Watts
Running Watts
1/8 HP
1/6 HP
1/4 HP
1/3 HP
1/2 HP
1/3 HP
1/2 HP
3/4 HP
1 HP
1-1/2 HP
2 HP
3 HP
5 HP
1-1/2 HP
5 HP
7-1/2 HP
10 HP
1/8 HP
1/6 HP
1/4 HP
1/3 HP
1/2 HP
800
1225
1600
2100
3175
2020
3075
4500
6100
8200
10550
15900
23300
8100
23300
35000
46700
1000
1400
1850
2400
3500
300
500
600
700
875
720
975
1400
1600
2200
2850
3900
6800
2000
6000
8000
10700
400
550
650
800
1100
16-6. Approximate Power Requirements For Farm/Home Equipment
Farm/Home Equipment
Stock Tank De-Icer
Grain Cleaner
Portable Conveyor
Grain Elevator
Milk Cooler
Milker (Vacuum Pump)
FARM DUTY MOTORS
Std. (e.g. Conveyors,
Feed Augers, Air
Compressors)
High Torque (e.g. Barn
Cleaners, Silo Unloaders,
Silo Hoists, Bunk Feeders)
3-1/2 cu. ft. Mixer
High Pressure 1.8 Gal/Min
Washer 2 gal/min
2 gal/min
Refrigerator or Freezer
Shallow Well Pump
Sump Pump
OM-4409 Page 72
Rating
1/4 HP
1/2 HP
3/4 HP
2 HP
1/3 HP
1/2 HP
3/4 HP
1 HP
1-1/2 HP
2 HP
3 HP
5 HP
1-1/2 HP
5 HP
7-1/2 HP
10 HP
1/2 HP
500 PSI
550 PSI
700 PSI
1/3 HP
1/2 HP
1/3 HP
1/2 HP
Starting Watts
Running Watts
1000
1650
3400
4400
2900
10500
1720
2575
4500
6100
8200
10550
15900
23300
8100
23300
35000
46700
3300
3150
4500
6100
3100
2150
3100
2100
3200
1000
650
1000
1400
1100
2800
720
975
1400
1600
2200
2850
3900
6800
2000
6000
8000
10700
1000
950
1400
1600
800
750
1000
800
1050
16-7. Approximate Power Requirements For Contractor Equipment
Contractor
Hand Drill
Circular Saw
Table Saw
Band Saw
Bench Grinder
Air Compressor
Electric Chain Saw
Electric Trimmer
Electric Cultivator
Elec. Hedge Trimmer
Flood Lights
Submersible Pump
Centrifugal Pump
Floor Polisher
High Pressure Washer
55 gal Drum Mixer
Wet & Dry Vac
Rating
Starting Watts
Running Watts
1/4 in
3/8 in
1/2 in
6-1/2 in
7-1/4 in
8-1/4 in
9 in
10 in
14 in
6 in
8 in
10 in
1/2 HP
1 HP
1-1/2 HP
2 HP
1-1/2 HP, 12 in
2 HP, 14 in
Standard 9 in
Heavy Duty 12 in
1/3 HP
18 in
HID
Metal Halide
Mercury
Sodium
Vapor
400 gph
900 gph
3/4 HP, 16 in
1 HP, 20 in
1/2 HP
3/4 HP
1 HP
1/4 HP
1.7 HP
2-1/2 HP
350
400
600
500
900
1400
4500
6300
2500
1720
3900
5200
3000
6000
8200
10500
1100
1100
350
500
2100
400
125
313
1000
1400
1250
600
900
4500
6100
3150
4500
6100
1900
900
1300
350
400
600
500
900
1400
1500
1800
1100
720
1400
1600
1000
1500
2200
2800
1100
1100
350
500
700
400
100
250
1000
200
500
1400
1600
950
1400
1600
700
900
1300
OM-4409 Page 73
16-8. Power Required To Start Motor
Single-Phase Induction Motor Starting Requirements
Motor Start
Code
G
H
J
K
L
M
N
P
KVA/HP
6.3
7.1
8.0
9.0
10.0
11.2
12.5
14.0
1
2
3
4
Motor Start Code
Running Amperage
Motor HP
Motor Voltage
To find starting amperage:
4
1
3
AC MOTOR
VOLTS 230
AMPS 2.5
CODE M
Hz
60
HP
1/4
PHASE 1
2
Step 1: Find code and use table to
find kVA/HP. If code is not listed,
multiply running amperage by six to
find starting amperage.
Step 2: Find Motor HP and Volts.
Step 3: Determine starting amperage (see example).
Welding generator amperage output must be at least twice the
motor’s running amperage.
(kVA/HP x HP x 1000) / Volts =
Starting Amperage
Example: Calculate starting amperage required for a 230 V, 1/4 HP motor with a motor start code of M.
Volts = 230, HP = 1/4, kVA/HP =
11.2
(11.2 x 1/4 x 1000) / 230 = 12.2A
Starting the motor requires 12.2
amperes.
S-0624
16-9. How Much Power Can Generator Supply?
1
Limit Load To 90% Of
Generator Output
Always start non-resistive (motor)
loads in order from largest to smallest, and add resistive loads last.
2
1
2
5 Second Rule
If motor does not start within 5
seconds, turn off power to prevent
motor damage. Motor requires
more power than generator can
supply.
Ref. ST-800 396-A / S-0625
OM-4409 Page 74
16-10. Typical Connections To Supply Standby Power
1
2
Utility
Electrical
Service
4
3
Transfer Switch
Fused
Disconnect
Switch
(If Required)
Welding
Generator
Output
!
Have only qualified persons
perform these connections
according to all applicable
codes and safety practices.
!
Properly install and ground
this equipment according to
its Owner’s Manual and national, state, and local codes.
Customer-supplied equipment
is required if generator will supply standby power during
emergencies or power outages.
1 Utility Electrical Service
5
2 Transfer Switch (Double-Throw)
Essential
Loads
Switch transfers the electrical load
from electric utility service to the
generator. Transfer load back to
electric utility when service is restored.
Install correct switch (customersupplied). Switch rating must be
same as or greater than the branch
overcurrent protection.
3 Fused Disconnect Switch
Install correct switch (customersupplied) if required by electrical
code.
4 Welding Generator Output
Generator output voltage and wiring must be consistent with regular
(utility) system voltage and wiring.
Connect generator with temporary
or permanent wiring suitable for the
installation.
Turn off or unplug all equipment
connected to generator before
starting or stopping engine. When
starting or stopping, the engine has
low speed which causes low voltage and frequency.
5 Essential Loads
Generator output may not meet the
electrical requirements of the premises. If generator does not produce
enough output to meet all requirements, connect only essential
loads (pumps, freezers, heaters,
etc. − See Section 16-4).
OM-4409 Page 75
16-11. Selecting Extension Cord (Use Shortest Cord Possible)
Cord Lengths for 120 Volt Loads
If unit does not have GFCI receptacles, use GFCI-protected extension cord.
Maximum Allowable Cord Length in ft (m) for Conductor Size (AWG)*
Current
(Amperes)
Load (Watts)
5
600
7
840
10
1200
15
4
6
8
10
12
14
350 (106)
225 (68)
137 (42)
100 (30)
400 (122)
250 (76)
150 (46)
100 (30)
62 (19)
400 (122)
275 (84)
175 (53)
112 (34)
62 (19)
50 (15)
1800
300 (91)
175 (53)
112 (34)
75 (23)
37 (11)
30 (9)
20
2400
225 (68)
137 (42)
87 (26)
50 (15)
30 (9)
25
3000
175 (53)
112 (34)
62 (19)
37 (11)
30
3600
150 (46)
87 (26)
50 (15)
37 (11)
35
4200
125 (38)
75 (23)
50 (15)
40
4800
112 (34)
62 (19)
37 (11)
45
5400
100 (30)
62 (19)
50
6000
87 (26)
50 (15)
*Conductor size is based on maximum 2% voltage drop
Cord Lengths for 240 Volt Loads
If unit does not have GFCI receptacles, use GFCI-protected extension cord.
Maximum Allowable Cord Length in ft (m) for Conductor Size (AWG)*
Current
(Amperes)
Load (Watts)
5
1200
7
1680
10
2400
15
4
8
10
12
14
700 (213)
450 (137)
225 (84)
200 (61)
800 (244)
500 (152)
300 (91)
200 (61)
125 (38)
800 (244)
550 (168)
350 (107)
225 (69)
125 (38)
100 (31)
3600
600 (183)
350 (107)
225 (69)
150 (46)
75 (23)
60 (18)
20
4800
450 (137)
275 (84)
175 (53)
100 (31)
60 (18)
25
6000
350 (107)
225 (69)
125 (38)
75 (23)
30
7000
300 (91)
175 (53)
100 (31)
75 (23)
35
8400
250 (76)
150 (46)
100 (31)
40
9600
225 (69)
125 (38)
75 (23)
45
10,800
200 (61)
125 (38)
50
12,000
175 (53)
100 (31)
*Conductor size is based on maximum 2% voltage drop
OM-4409 Page 76
6
SECTION 17 − SELECTING AND PREPARING A TUNGSTEN
FOR DC OR AC WELDING
gtaw_Phase_2007−04
!
Whenever possible and practical, use DC weld output instead of AC weld output.
17-1. Selecting Tungsten Electrode (Wear Clean gloves To Prevent Contamination Of Tungsten )
Amperage Range - Gas Type♦ - Polarity
Electrode Diameter
(DCEN) − Argon
AC − Argon
Direct Current Electrode Negative
Balance Control @ 65% Electrode Negative
(For Use With Aluminum)
(For Use With Mild Or Stainless Steel)
2% Ceria (Orange Band), 1.5% Lanthanum (Gray Band), Or 2% Thorium (Red Band) Alloy Tungstens
.040” (1 mm)
25-85
20-80
1/16” (1.6 mm)
50-160
50-150
3/32” (2.4 mm)
135-235
130-250
250-400
225-360
1/8” (3.2 mm)
Pure Tungsten (Green Band)
.040” (1 mm)
Pure Tungsten Not Recommended
10-60
1/16” (1.6 mm)
For DCEN − Argon
50-100
3/32” (2.4 mm)
100-160
1/8” (3.2 mm)
150-210
♦Typical argon shielding gas flow rates are 11 to 35 cfh (cubic feet per hour).
Figures listed are a guide and are a composite of recommendations from American Welding Society (AWS) and electrode manufacturers.
17-2. Preparing Tungsten Electrode For Welding With Phase Control Machines
!
Grinding the tungsten electrode produces dust and flying sparks which can cause injury and start fires. Use
local exhaust (forced ventilation) at the grinder or wear an approved respirator. Read MSDS for safety information. Consider using tungsten containing ceria, lanthana, or yttria instead of thoria. Grinding dust from
thoriated electrodes contains low-level radioactive material. Properly dispose of grinder dust in an environmentally safe way. Wear proper face, hand, and body protection. Keep flammables away.
A. Preparing Tungsten For DC Electrode Negative (DCEN) Welding
2-1/2 Times
Electrode Diameter
Radial Grinding
Causes Wandering Arc
1
3
2
1
Grinding Wheel
Grind end of tungsten on fine grit, hard
abrasive wheel before welding. Do not use
wheel for other jobs or tungsten can become
contaminated causing lower weld quality.
2
Tungsten Electrode
A 2% ceriated tungsten is recommended.
4
Wrong Tungsten Preparation
Ideal Tungsten Preparation − Stable Arc
3
Flat
Diameter of this flat determines amperage
capacity.
4
Straight Ground
Grind lengthwise, not radial.
B. Preparing Tungsten For AC Welding
1
Tungsten Electrode
A pure tungsten is recommended..
1 − 1-1/2 Times
Electrode Diameter
1
2
2
Balled End
Ball end of tungsten by applying AC amperage recommended for a given electrode
diameter (see Section 17-1). Let ball on end
of the tungsten take its own shape.
OM-4409 Page 77
SECTION 18 − GUIDELINES FOR TIG WELDING (GTAW)
gtaw 7/2006
18-1. Positioning The Torch
!
Grinding the tungsten electrode produces dust and flying sparks which can cause
injury and start fires. Use local exhaust (forced ventilation) at the grinder or wear an
approved respirator. Read
MSDS for safety information.
Consider using cerium or
lanthanum based tungsten
instead of thoriated. Thorium dust contains low-level
radioactive material. Properly dispose of grinder dust in
an environmentally safe way.
Wear proper face, hand, and
body protection. Keep flammables away.
1
Workpiece
3
2
4
90°
1
Make sure workpiece is clean
before welding.
2
Work Clamp
Place as close to the weld as
possible.
10−15°
4
5
6
10−25°
3
4
5
6
Torch
Filler Rod (If Applicable)
Gas Cup
Tungsten Electrode
Select and prepare tungsten
according to Section 17.
Guidelines:
5
6
1/16 in
3/16 in
Bottom View Of Gas Cup
The inside diameter of the gas cup
should be at least three times the
tungsten diameter to provide adequate shielding gas coverage. (For
example, if tungsten is 1/16 in
diameter, gas cup should be a
minimum of 3/16 in diameter.
Tungsten extension is the distance
the tungsten extends out gas cup of
torch.
The tungsten extension should be
no greater than the inside diameter
of the gas cup.
Arc length is the distance from the
tungsten to the workpiece.
Ref. ST-161 892
OM-4409 Page 78
18-2. Torch Movement During Welding
Tungsten Without Filler Rod
75°
Welding direction
Form pool
Tilt torch
Move torch to front
of pool. Repeat process.
Tungsten With Filler Rod
75°
Welding direction
Form pool
Tilt torch
Remove rod
15°
Add filler metal
Move torch to front
of pool. Repeat process.
ST-162 002-B
OM-4409 Page 79
18-3. Positioning Torch Tungsten For Various Weld Joints
90°
Butt Weld And Stringer Bead
70°
20°
20°
“T” Joint
70°
10°
20°
40°
Lap Joint
70°
20°
30°
90°
Corner Joint
70°
20°
ST-162 003 / S-0792
OM-4409 Page 80
Notes
Welding Symbols
Ref. AWS/ANSI A2.4
OM-4409 Page 81
SECTION 19 − PARTS LIST
Hardware is common and not
available unless listed.
17
3
18
2
25
19
21
1
16
8
7
4
29
20
23
15
30
9
13
12
11
6
28
24
22
31
14
32
33
5
10
133
34
35
123
148
15
147
146 − Figure 19−5
134
130
132
135
136
131 − Figure 19−2
138
139
140
145
124
125
126
137
127
141
143
129
142
144 − Figure 19−3
Figure 19-1. Main Assembly
OM-4409 Page 82
128
47
46
45
150
70
69
65
44
61
51
42
41
43
38
39
40
64
50
56
55
54
49
75
58
57
36
76
74
77
60
53
151
52
113
114
115
112 − Figure 19−4
119
93
92
94
98
121
120
83
84
85
90
9186
87
95
97
78
81
82
88
89
116
117
118
73
66
59
37
72
67 68
62
63
48
71
99100
96
101
102
104
149
111
110
80
79
103
105
106
107
109
122
108
803 324-F
OM-4409 Page 83
74
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-1. Main Assembly
. . . 1 . . . . . . . . . . . . . . 189824 . . Panel, Gen LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 2 . . . . . . . . . . . . . . 189828 . . Panel, Engine Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 3 . . . . . . . . . . . . . . 206601 . . Panel, Engine Extension LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 4 . . . . . Z1 . . . . . 208277 . . Reactor, AC Environmental Rda . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 5 . . . . CR7 . . ♦188636 . . Relay, OCV Control (Battery Charging) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 6 . . . . . . . . . . . . ♦081499 . . Bracket, Mtg Strip Terminal (Battery Charging) . . . . . . . . . . . . . . . . . . . . . .
. . . 7 . . . . . . . . . . . . . . 038620 . . Link, Jumper Term Blk 30 Amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 1T . . . . . 189549 . . Block, Term Assy Standard W/Clamp (includes) . . . . . . . . . . . . . . . . . . . . .
. . . 8 . . . . . . . . . . . . . . 038621 . . . . Block, Term 30 Amp 4 Pole Frict Term Str Both Side . . . . . . . . . . . . . . .
. . . 9 . . . . . . . . . . . . . . 081499 . . . . Bracket, Mtg Strip Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 138027 . . . . Edge Trim, Style Tl750−b2x1/16 Black W/Clips 3.750 . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 020225 . . . . Clamp, Nyl .875 Clamp Dia X.500 Wide .203 Mtg Hole . . . . . . . . . . . . .
. . . 10 . . SR4, SR5 . . 035704 . . Rectifier, Integ Bridge 40 Amp 800 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 11 . . . . CB4 . . . . 045061 . . Circuit Breaker, Auto Reset 24vdc 7 Amp . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 12 . . . . . . . . . . . . . . 206352 . . Brace, Front To Center Upright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 13 . . . . . T1 . . . . . 205636 . . Transformer, W/Brkt Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 14 . . . . . . . . . . . . . . 201697 . . Pan, Reactor And Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 15 . . . . . . . . . . . . . . 173352 . . Extrusion, Rubber (order by ft.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 16 . . . . . . . . . . . . . . 189708 . . Firewall, Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 17 . . . . . . . . . . . . . . 194485 . . Hose, Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 18 . . . . . . . . . . . . . . 189764 . . Air Cleaner, Intake (Engine) (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . *192938 . . . . Filter, Air Element Primary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . *192939 . . . . Filter, Air Element Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 206556 . . Pipe, Air Cleaner Intake Deutz (Turbo Hose To Air Cleaner Hose) . . . . .
. . . 19 . . . . . . . . . . . . . . 189763 . . Bracket, Mtg Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 20 . . . . . . . . . . . . . . 206351 . . Upright, Center Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 21 . . . . . . . . . . . . . . 189464 . . Seal, Weather Lift Eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 22 . . . . . . . . . . . . . . 197613 . . Air Cleaner, Intake 5.250 In (Compressor) (includes) . . . . . . . . . . . . . . . . .
. . . 23 . . . . . . . . . . . . . . 197675 . . . . Dust Ejector, Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . *197676 . . . . Element, Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 197677 . . . . Cover Assy, Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 197678 . . . . Body, Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . *197679 . . . . Element, Air Cleaner Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 24 . . . . . . . . . . . . . . 197829 . . . . Bracket, Mtg Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 25 . . . . . . . . . . . . . . 213144 . . Hose, Elbow Air Cleaner/Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 26 . . . . . . . . . . . . . . . . . . . . . . . . n/a
. . . 27 . . . . . . . . . . . . . . . . . . . . . . . . n/a
. . . 28 . . . . . . . . . . . . . . 207268 . . Hose, Cwc Flexaust 2.000 Id X 22.000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 29 . . . . . . . . . . . . . +219140 . . Bracket, Mtg Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 30 . . . . . . . . . . . . . . 210151 . . Label, Air Cleaner Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 31 . . . . . . . . . . . . ♦209612 . . Lever, Switch Lockout Disconnect Battery . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 32 . . . . . . . . . . . . ♦209597 . . Bracket, Mtg Battery Disconnect Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 33 . . . . . . . . . . . . . ♦209611 . . Switch, Disc Battery 2P 6−36 Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 34 . . . . . . . . . . . . . . 196220 . . Bracket, Holddown Fuel Tank Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 35 . . . . . . . . . . . . . . 192362 . . Bracket, Mtg Nyl 1/2 Conduit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 36 . . . . . . . . . . . . . +206603 . . Cover, Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 37 . . . . . . . . . . . . . . 189052 . . Grommet, Plastic Neck Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 38 . . . . . . . . . . . . . . 190198 . . Cap, Tank Screw−on 3.500 In W/Vent W/Lanyard 8” . . . . . . . . . . . . . . . . .
. . . 39 . . . . . . . . . . . . . . 192041 . . Label, Use Diesel Fuel Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 40 . . . . . . . . . . . . . . 222513 . . Label, Warning Falling Equipment Can Cause Serious . . . . . . . . . . . . . . .
. . . 41 . . . . . . . . . . . . ♦143915 . . Mount, Sgl Stud 1.5 Dia X 1.000 Lg .312−18 Stud . . . . . . . . . . . . . . . . . . .
. . . 42 . . . . . . . . . . . . ♦205702 . . Bracket, Mtg Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 43 . . . . . . . . . . . . ♦205749 . . Pipe, Exhaust Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 44 . . . . . . . . . . . . ♦603767 . . Cap, Weather Exhaust No. 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 45 . . . . . . . . . . . . ♦010875 . . Clamp, Muffler 2.000 Dia U Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 46 . . . . . . . . . . . . ♦205712 . . Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 47 . . . . . . . . . . . . ♦205748 . . Pipe, Exhaust Elbow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-4409 Page 84
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-1. Main Assembly (Continued)
. . . 48 . . . . . . . . . . . . . . 224265
. . . 49 . . . . . . . . . . . . . . 213895
. . . 50 . . . . . . . . . . . . . . 202633
. . . 51 . . . . . . . . . . Figure 19-7
. . . 52 . . . . . . . . . . . . . . 191577
. . . 53 . . . . . . . . . . . . . . 191809
. . . 54 . . . . . . . . . . . . . . 209632
. . . 55 . . . . . . . . . . . . . . 218619
. . . . . . . . . . . . . . . . . . . . 193256
. . . . . . . . . . . . . . . . . . . . 195748
. . . . . . . . . . . . . . . . . . . . 195746
. . . . . . . . . . . . . . . . . . . . 195745
. . . . . . . . . . . . . . . . . . . *067265
. . . . . . . . . . . . . . . . . . . *066217
. . . . . . . . . . . . . . . . . . . . 208041
. . . . . . . . . . . . . . . . . . . . 193230
. . . . . . . . . . . . . . . . . . . . 194403
. . . . . . . GLOW PLUG . 190059
. . . 56 . . . . . . . . . . . . . . 207203
. . . . . . . . . . . . . . . . . . . . 208042
. . . 57 . . . . . . . . . . . . . *207808
. . . 58 . . . . . . . . . . . . . . 209675
. . . 59 . . . . . . . . . . . . . . 209633
. . . 60 . . . . . . . . . . . . . . 209621
. . . 61 . . . . . . . . . . . . . . 207269
. . . 62 . . . . . . . . . . . . . . 206749
. . . 63 . . . . . . . . . . . . . . 206558
. . . 64 . . . . . . . . . . . . . . 209623
. . . 65 . . . . . . . . . . . . . . 201749
. . . 66 . . . . . . . . . . . . . . 201006
. . . 67 . . . . BATT . . . . 190897
. . . 68 . . . . . . . . . . . . . . 108081
. . . 69 . . . . . . . . . . . . . . 190206
. . . 70 . . . . . . . . . . . . . . 190207
. . . 71 . . . . . . . . . . . . . . 203430
. . . 72 . . . . . . . . . . . . . +201183
. . . 73 . . . . . . . . . . . . . . 168385
. . . 74 . . . . . . . . . . . . . . 225120
. . . 75 . . . . . . . . . . . . . +206602
. . . 76 . . . . . . . . . . . . . . 207270
. . . 77 . . . . . . . . . . . . . . 210229
. . . 78 . . . . . . . . . . Figure 19-7
. . . 79 . . . . . . . . . . . . . . 208024
. . . 80 . . . . . . . . . . . . . . 206613
. . . 81 . . . . . . . . . . . . . . 199849
. . . 82 . . . . . . . . . . . . . . 071731
. . . 83 . . . . . . . . . . . . . . 191812
. . . 84 . . . . . . . . . . . . . . 071890
. . . 85 . . . . . . . . . . . . . . 071730
. . . 86 . . . . . . . . . . . . . . 083476
. . . 87 . . . . . . . . . . . . . . 135205
. . Label, Warning Hot Exhaust Parts Do Not Touch . . . . . . . . . . . . . . . . . . . .
. . Manifold, Exhaust Muffler Bf4m2011 Deutz . . . . . . . . . . . . . . . . . . . . . . . . .
. . Support, Cover E−coat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Air Compressor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Guard, Starter Deutz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Engine LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Hose, Tubing Oil Assyw/Fittings 22.380lg . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Engine, Deutz Dsl Elec Bf4m2011 (includes) . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Adapter, Engine Deutz 1011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Flywheel, Deutz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Sender, Coolant Temp & 130c Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Switch, Pressure Oil 1.5 Bar Nc Cont . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Secondary Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spacer, Stl .323 Id X .625 Od X .141 Thk (Alternator) . . . . . . . . . . . . . . . .
. . Sender, Pressure Oil 0− 100 Psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Adaptor, Oil Pressure Sender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Glow Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Fan, Engine Cooling 18.000 Suction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spacer, Stl .800id X 1.188od X .090 Thk (Fan Hub Bolt) . . . . . . . . . . . . . .
. . Belt, V .375 X 45.125 Lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Extension, Hydraulic 37 Deg Flare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Hose, Tubing Oil Assyw/Fittings 27.040lg . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Stl Adapter 3/4 Sae−3/4 Jic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Guard, Fan LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Shroud, Fan Air Pak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cooler, Oil Engine/Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Brs Adapter Long 3/4 Sae−3/4 Jic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Upright, Rear Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bolt, J Stl .312−18 X 7.750 Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Battery, Stor 12v 650 Crk 110 Rsv Gp 24 Maint Free . . . . . . . . . . . . . . . .
. . Terminal Protector, Battery Post Mtg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cable, Bat Neg 42 In Lg 2 Awg W/Clamp & .375 Rng . . . . . . . . . . . . . . . .
. . Cable, Bat Pos 45 In Lg No 1 Awg W/Clamp & .406 Rng . . . . . . . . . . . . .
. . Bracket, Battery Holddown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cover, Battery Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Warning Battery Explosion Can Blind . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Warning Moving Parts Can Cause Injury . . . . . . . . . . . . . . . . . . . . . .
. . Panel, Engine Extension R.H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Guard, Fan RH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Compressor Oil Fill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Air Compressor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pulley, Fan Assy W/Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Fan/Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Screw, 625−11x4.00 Hex Hd−pln Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Flat .656idx2.250odx.187t Stl Pld . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Engine R.h. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Retainer, Mount Eng/Gen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Tubing, Stl .875 Od X12ga Wall X 2.500 . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Mount, Eng/Gen Nprn .875id X 2.500od X 2.000 60 Dur . . . . . . . . . . . . . .
. . Nut, 625−11 .94hex .77h Stl Pld Elastic Stop Nut . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
7
1
1
1
1
1
1
4
4
1
4
4
4
4
OM-4409 Page 85
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-1. Main Assembly (Continued)
. . . . . . . . . . . . . . . . . . . . 199505
. . . 88 . . . . . . . . . . . . . . 165271
. . . 89 . . . . . . . . . . . . . . 176529
. . . 90 . . . . . . . . . . . . . . 113854
. . . 91 . . . . . . . . . . . . . . 176528
. . . 92 . . . . . . . . . . . . . . 173336
. . . 93 . . . . . . . . . . . . . . 066298
. . . 94 . . . . . . . . . . . . . . 218003
. . . 95 . . . . . . . . . . . . . . 232968
. . . 96 . . . . . . . . . . . . . *192744
. . . . . . . . . . . . . . . . . . . . 199383
. . . . . . . . . . . . . . . . . . . . 191819
. . . 97 . . . . . . . . . . . . . . 190992
. . . 98 . . . . . . . . . . . . . . 206604
. . . 99 . . . . . . . . . . . . . . 209093
. . 100 . . . . . . . . . . . . . 209092
. . 101 . . . . . . . . . . . . . 174064
. . . . . . . . . . . . . . . . . . . . 196036
. . . . . . . . . . . . . . . . . . . . 125663
. . . . . . . . . . . . . . . . . . . . 175936
. . . . . . . . . . . . . . . . . . . . 127994
. . . . . . . . . . . . . . . . . . . . 127648
. . . . . . . . . . . . . . . . . . . . 124974
. . . . . . . . . . . . . . . . . . . . 601868
. . . . . . . . . . . . . . . . . . . . 126388
. . . . . . . . . . . . . . . . . . . . 089800
. . . . . . . . . . . . . . . . . . . . 108941
. . . . . . . . . . . . . . . . . . . . 156733
. . 102 . . . . . . . . . . . . . 209090
. . 103 . . . . . . . . . . . . +209089
. . 104 . . . . . . . . . . . . . 206464
. . 105 . . . . . . . . . . . . . 199592
. . 106 . . . . . . . . . . . . . 210681
. . 107 . . . . . . . . . . . . . 209091
. . 108 . . . . . . . . . . . . . 191626
. . 109 . . . . . . . . . . . . +189827
. . 110 . . . . . . . . . . . . . 207448
. . 111 . . . . . . . . . . . . . 209059
. . 112 . . . . . . . . . Figure 19-5
. . 113 . . . . . . . . . . . . . 218087
. . 114 . . . . . . . . . . . . . 124253
. . 115 . . . . . . . . . . . . . 189912
. . 116 . . . . . . . . . . . . . 189909
. . 117 . . . . . . . . . . . . . 189913
. . 118 . . . . . . . . . . . . . 190142
. . 119 . . . . . . . . . . . . . 189910
. . 120 . . . . . . . . . . . . . 189908
. . 121 . . . . . . . . . . . . . 181572
. . . . . . . . . . . . . . . . . . . . 196219
. . 122 . . . . . . . . . . . . . 191446
. . 123 . . . . . . . . . . . . . 209094
. . 124 . . . . . . . . . . . . +212224
. . 125 . . . . . . . . . . . . . 191897
. . 126 . . . . . . . . . . . . . 224266
. . 127 . . . . . . . . . . . . . 206463
. . 128 . . . . . . . . . . . . . 233953
OM-4409 Page 86
. . Hose Assy, Oil Drain 32.000 Lg (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Valve, Oil Drain 3/8−18 Nptf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Ftg, Hose Brs Barbed Fem 1/2 Tbg X 3/8 Npt . . . . . . . . . . . . . . . . . . . . . 1
. . . . Hose, Sae .500 Id X .780 Od Xcoil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.666
. . Ftg, Hose Brs Barbed Elbow M 1/2 Tbg X 1/2 Npt . . . . . . . . . . . . . . . . . . . 1
. . Ftg, Adapter Oil Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Ring (Oil Drain) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bracket, Mtg Fuel Filter/Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Base, Fuel Filter Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Filter, Fuel Spin−on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Hose, Sae .312 Id X .560 Od X 8.000 (Fuel Filter To Fuel Pump) . . . . . . 1
. . Hose, Sae .312 Id X .560 Od X 14.000 (Fuel Tank To Fuel Filter) . . . . . . 1
. . Keeper, Latch Engine Access Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Channel, Stiffener Engine Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bracket, Safety Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bracket, Mtg Saftey Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Idle, Solenoid Assy (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Bracket, Arm Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Ball Joint, .250−28 Type Sp Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Rod, Throttle 5.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Ball Joint, .250−28 Type Spf Female Rod End . . . . . . . . . . . . . . . . . . . . 1
. . . . Clevis, Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Solenoid, 12vdc Pull/Hold Type 1” Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Nut, 250−28 .44hex .26h Stl Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . Nut, 250−28 .44hex .27h Stl Pld Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Nut, 250−20 .44hex .22h Stl Pld .58d Flange Defor . . . . . . . . . . . . . . . . 1
. . . . Screw, 250−20x1.00 Hexwhd.61d Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Nut, 250−28 .44hex .13h Stl Pld Sem Cone Wshr.51d . . . . . . . . . . . . . . 1
. . Bracket, Stiffener Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . Panel, Engine Access Lift Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Label, Maintenance Big Blue Air Pak Deutz Ce . . . . . . . . . . . . . . . . . . . . . 1
. . Latch, Paddle Series 20 (Black) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Handle, Pocket Pull Door Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Panel, Rocker Short . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bumper, Door Engine Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . Panel, Gen Rh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Label, Maintenance I R Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Label, Schematic Air System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Generator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Tank, Fuel (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Bushing, Tank Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . Ftg, Stl Barbed Elbow W/.047in Orifice Zinc Pld . . . . . . . . . . . . . . . . . . . 1
. . . . Ftg, Stand Pipe Hose .250 X 9.265lg 90 Deg Zinc . . . . . . . . . . . . . . . . . 1
. . . . Ftg, Stl Barbed Elbow Zinc Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Sender, Fuel Gauge 9.750 Deep Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Ftg, Stand Pipe Hose .3125 X 9.260lg 90 Deg Zinc . . . . . . . . . . . . . . . . 1
. . . . Valve, Drain Fuel 180 Deg Zinc Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Bushing, Tank Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Hose, Sae .250 Id X .500 Od X 26.000 (Fuel Return Line) . . . . . . . . . . . . 1
. . Extrusion, Rubber w/Adhesive 1.000 x 1.000 (order by ft.) . . . . . . . . . . . . 6ft
. . Bracket, Mtg Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bracket, Mtg Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . Label, Do Not Weld On Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . Label, Manufacturing Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Label, Warning General Precautionary CSA . . . . . . . . . . . . . . . . . . . . . . . . . 2
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-1. Main Assembly
. . 129 . . . . R3 . . . . . 189699
. . 130 . . . . . . . . . . . . . 218086
. . 131 . . . . . . . . . Figure 19-2
. . 132 . . . . . . . . . . . . . 189731
. . 133 . . . . . . . . . . . . . 203260
. . 134 . . . . . . . . . . . . . 191448
. . 135 . . . . . . . . . . . . . 206609
. . 136 . . . . . . . . . . . . +206606
. . 137 . . . . . . . . . . . . . 209682
. . 138 . . . . . . . . . . . ♦039047
. . 139 . . . . . . . . . . +♦207095
. . 140 . . . . . . . . . . . ♦039046
. . 141 . . . . . . . . . . . ♦210156
. . 142 . . . . . . . . . . . . . 207096
. . 143 . . . . . . . . . . . . . 209683
. . 144 . . . . . . . . . Figure 19-3
. . 145 . . . CT1 . . . . 202130
. . 146 . . . . . . . . . Figure 19-6
. . 147 . . . . . . . . . . . . . 193453
. . 148 . . . PC1 . . . . 207397
. . 149 . . . . . . . . . . . . . 085963
. . 150 . . . . . . . . . . . . . 105734
. . 151 . . . . . . . . . . . . . 233088
. . . . . . . . . . . . . . . . . . . . 049525
. . . . . . . . . . . . . . . . . . . . 049525
. . . . . . . . . . . . . . . . . . . . 237013
. . . . . . . . . . . . . . . . . . . . 206468
. . . . . . . . . . . . . . . . . . . ♦195118
. . . . . . . . . . . . . . . . . . ♦209238
. . . . . . . . . . . . . . . . . . ♦209240
. . . . . . . . . . . . . . . . . . ♦209236
. . . . . . . . . . . . . . . . . . ♦209241
. . . . . . . . . . . . . . . . . . ♦209242
. . . . . . . . . . . . . . . . . . ♦189975
. . . . . . . . . . . . . . . . . . ♦155146
+
*
. . Resistor, WW Tap 375 W 10 Ohm W/Mtg Bkt . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Holddown Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Firewall, Bottom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Caution Do Not Use Ether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cover, Top Front Upright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Upright, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Box, Valve Ball . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Air Power Ingersoll−Rand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Terminal, Pwr Output Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Box, Battery Charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Terminal, Pwr Output Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Battery Charge (Battery Charge +/−) . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cover, Box Front Upright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Warning Safety Air System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Panel, Front w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Xfmr, Current Sensing (Auto Idle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Main Rectifier Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Box Fcr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Module, Field Current Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spring, Ext .375 Od X .041 Wire X 2.000 (ForSafety Latch) . . . . . . . . . . .
. . Pipe, Muffler Extension Elbow 1.750 OD . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Danger Using A Generator Indoors Can Kill You In Minutes . . . . .
. . Nut, 312−18 U−nut Multi−thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Nut, 312−18 U−nut Multi−thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, Hour/Fuel Meter Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Kit, Label (Includes Safety And Informational Labels) . . . . . . . . . . . . . . . . .
. . Kit, Lock-Out Vandalism (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Door, Access Rh W/Om Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Door, Access Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Tab, Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Mount, Access Rh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Mount, Access Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Hinge, Door Access 180 Deg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Sponge, Nprn .060 X 1.000 Wide X 4.000 Sce 41 Close . . . . . . . . . . . .
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
1
1
1
1
1
1
1
1
4
3
When ordering a component originally displaying a precautionary label, the label should also be ordered.
Recommended Spare Parts.
♦Optional
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4409 Page 87
Hardware is common and
7
not available unless listed.
6
5
9
8
10
4
11
12
13
3
1
2
16
14
19
18
15
17
26
20
21
22
23
24
25
803 325-E
Figure 19-2. Control Box Assembly
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-2. Control Box Assembly − (Figure 19-1 Item 131)
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1 . . . F1, F2 . . . 085874
2 . . . . . . . . . . . . . . 046432
3 . . . . . . . . . . . . . . 134201
4 . . . . PC9 . . . . 192224
5 . . . . . . . . . . . . . . 201077
6 . . . . . . . . . . . . . . 201078
7 . . . . HM2 . . ♦145247
8 . . CR3,CR6 . . 090104
9 . . . . CR8 . . . . 197325
10 . . . . CB15 . . . . 083432
11 . . . . CB8 . . ♦139266
12 C8/D8,C10/D10,D12 189701
13 . . . . CR1 . . . . 214876
14 . . . . CB14 . . . . 205927
15 . CB10,CB16 . 190374
16 . . . . CR5 . . . . 223710
17 . . . . CR14 . . ♦090104
18 . . . . SR1 . . . . 035704
19 . . . . PC7 . . . . 195706
20 . . . . C1/D1 . . . . 189701
21 . . . . . C9 . . . . . 087110
22 . . . . . . . . . . . . . . 177136
OM-4409 Page 88
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
Fuse, Mintr Cer Slo−blo 10. Amp 250 Volt . . . . . . . . . . . . . . . . . . . . . . . . . .
Holder, Fuse Mintr .250 X 1.250 Panel Mtg . . . . . . . . . . . . . . . . . . . . . . . . .
Stand−off Support, Pc Card .312/.375w/Post&lock .43 . . . . . . . . . . . . . . .
Circuit Card Assy, Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Box, LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Box, Rh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Meter, Hour Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Relay, Encl 12vdc Spst 30a/15vdc 5pin Flange Mtg . . . . . . . . . . . . . . . . . .
Relay, Encl 12vdc Spst 70a 4pin Flange Mtg . . . . . . . . . . . . . . . . . . . . . . . .
Supplementary Protector, Man Reset 1p 10a 250vac Frict . . . . . . . . . . . .
Supplementary Protector, Man Reset 1p 15a 250vac Frict (Air Dryer) . . .
Diode/Capacitor Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Relay, Encl 6vdc Spst 35a/14vdc 5 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Breaker, Auto Reset 12vdc 12 Amp . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Breaker, Auto Reset 12vdc 40 Amp . . . . . . . . . . . . . . . . . . . . . . . . .
Relay, Encl12vdc Dpst−no 25a 6pin Flange . . . . . . . . . . . . . . . . . . . . . . . . .
Relay, Encl 12vdc Spst 30a/15vdc 5pin Flange Mtg (Air Dryer) . . . . . . . .
Rectifier, Integ Bridge 40. Amp 800v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module, Pull To Idle, Two Output, 7 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diode/Capacitor Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacitor, Elctlt 240 Uf 200 Vdc Can 1.39 Di . . . . . . . . . . . . . . . . . . . . . . .
Clamp, Capacitor 1.375 Dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
3
1
1
1
1
2
1
1
1
3
1
1
2
1
1
1
1
1
1
1
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-2. Control Box Assembly (Continued)
. . . 23 . . . . . . . . . . . . . . 238691 . . Label, Layout Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 24 . . . . . . . . . . . . . . 201079 . . Cover, Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 25 . CR4, CR10 . 113247 . . Relay, Encl 12vdc Dpdt 20a/120vac 8pin Flange Mtg . . . . . . . . . . . . . . . .
. . . 26 CB11,CB12,CB13 139266 . . Supplementary Protector, Man Reset 1p 15a 250vac Frict . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 237754 . . Harness, Engine Deutz Bf4m2011 (includes) . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 156734 . . . . Nut, 010−32 .31hex .13h Stl Pld Sem Cone Wshr.38d . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 148850 . . . . Socket, Relay 5 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . S2 . . . . . 021467 . . . . Switch,Tgl Spst 3a 250v Off−none−(On) Spd Term
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Located On Front Panel, See Figure 19-3) . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 211292 . . . . Conn, Body 5 Terminal (For Ignition Switch S1) . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 211293 . . . . Conn, Pack Terminal Position Assurance(Lock) . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 214932 . . . . Conn, Rect Univ 039 8p/S 2row Plug Cable Lkg Seal . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 150316 . . . . Conn, Rect Univ 039 6p/S 3row Plug Cable Lkg . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . S10 . . . . 206624 . . . . Switch, Tgl Sptt 6a 125vac (On)−on−(On) Spd Term
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Located On Front Panel, See Figure 19-3) . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 164617 . . . . Clip,Wiring Straight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 219873 . . Harness, Control Box, Weld Control LH (includes) . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . RC3 . . . . 158466 . . . . Conn, Rect Univ 084 12p/S 3row Rcpt Cable/Panel Lkg . . . . . . . . . . . .
. . . . . . . . . . RC1 . . . . 135133 . . . . Conn, Rect Univ 084 9p/S 3row Rcpt Cable/Panel Lkg . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 204737 . . . . Cable Tie Mount, Winged Push . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . CR15 . . ♦172015 . . Time Delay Relay (Air Dryer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
3
1
4
5
1
1
1
1
4
1
2
1
1
1
3
1
♦Optional
*Recommended Spare Parts.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4409 Page 89
Hardware is common and
not available unless listed.
53
3
2
4
5
8
6
1
9
7
10
11
12
13
58
57
56
14
15
55
16
17
18
19
54
52
51
50
47
48 46
49
30
45
21
28
22
23
44
31
43
20
25
29
27
32
24
26
33
34
36
42
35
41
40
39
38
37
803 326-C
Figure 19-3. Panel, Front w/Components
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-3. Panel, Front w/Components (Figure 19-1 Item 144)
... 1 ..............
... 2 ..............
. . . 3 . . . . . S3 . . . . .
....................
. . . . . . . . . . RC6 . . . .
. . . 4 . . . . . R1 . . . . .
OM-4409 Page 90
236974
236608
208278
192558
148389
193118
. . Plate, Screened Ident Control Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Panel, Engine/Weld Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Switch, Range/Changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Harness, Range Switch (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Conn, Rect Univ 084 4p/S 1row Rcpt Cable/Panel Lkg . . . . . . . . . . . . .
. . Pot, Cp Flat 1t 2. W 1k Ohm Linear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-3. Panel, Front w/Components (Continued)
. . . . . . . . . . . . . . . . . . . . 206809 . . Harness, Weld Control (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 5 . . . . . S6 . . . . . 193234 . . . . Switch, Rotary 6 Position Gold Contacts . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 197257 . . . . Guard, Circuit Breaker (For S6 − Not Included w/Harness) . . . . . . . . . .
. . . 6 . . . . . S5 . . . . . 011609 . . . . Switch, Tgl Spdt 15a 125vac On−none−on Spd Term Chr . . . . . . . . . . .
. . . . . . . . . . PLG9 . . . . 193183 . . . . Conn, Rect Cinch 18 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 196603 . . . . Seal, Switch 6 Position Rotary .250 Shaft . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . PLG14 . . . 141450 . . . . Conn, Rect Metrmate 10skt 1row Plug Cable Lkg . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 164617 . . . . Clip,Wiring Straight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . PLG10 . . . 150316 . . . . Conn, Rect Univ 039 6p/S 3row Plug Cable Lkg . . . . . . . . . . . . . . . . . . .
. . . 7 . . . . CB5 . . . . 139266 . . . . Supplementary Protector, Man Reset 1p 15a 250vac Frict . . . . . . . . . .
. . . . . . . . . . CB6 . . . . 139266 . . . . Supplementary Protector, Man Reset 1p 15a 250vac Frict . . . . . . . . . .
. . . 8 . . . . . . . . . . . . . . 202209 . . Spacer, Nylon .221 Thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 9 . . . . PC6 . . . . 192995 . . Circuit Card Assy, Connector/Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 10 . . . . . S1 . . . . . 212436 . . Switch, Ignition 4 Position W/Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 11 . . . . . S10 . . . . 206624 . . Switch, Tgl Sptt 6a 125vac (On)−on−(On) Spd Term (Included In Engine
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring Harness, See Figure Figure 19-2) . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 12 . . . . . S2 . . . . . 021467 . . Switch,Tgl Spst 3a 250v Off−none−(On) Spd Term (Included In Engine
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring Harness, See Figure Figure 19-2) . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . Figure 19-4 . . Auxiliary Power Group , Export
. . . . . . . . . . . . . . . . . . . 215 437 . . Auxiliary Power Group, Domestic (Includes)
. . . 13 . . . . CB1 . . . . 201083 . . . . Supplementary Protector, Man Reset 2p 20a 250vac . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 201553 . . . . Clip, Retaining Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 201109 . . . . Harness, Receptacle Auxillary Power (includes) . . . . . . . . . . . . . . . . . . .
. . . 14 . . . . CB2 . . . . 093996 . . . . . . Supplementary Protector, Man Reset 1p 20a 250vac Frict . . . . . . . .
. . . 15 . . . GFCI1 . . . 151981 . . . . . . Rcpt, Str Dx Grd 2p3w 15/20a 125v *5−20r Gfi . . . . . . . . . . . . . . . . . .
. . . 16 . . . . RC1 . . . . 147632 . . . . . . Rcpt,Tw Lk Grd 2p3w 30a 250v *L6−30r . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 010146 . . . . . . Clamp, Nyl .625 Clamp Dia X.500 Wide .203 Mtg Hole . . . . . . . . . . .
. . . 17 . . . . RC5 . . ♦182954 . . . . Rcpt, Str 3p4w 50a 125/250v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 18 . . . . . . . . . . . . ♦025248 . . . . Stand-off, Insul .250-20 X 1.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 19 . . . . . . . . . . . . ♦604102 . . . . Connector, Clamp Cable 1.000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 20 . . . . . . . . . . . . ♦197527 . . . . Guard, Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 21 . . . . . . . . . . . . ♦197363 . . . . Terminal, Ring Tng Screw Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 22 . . . . CB7 . . ♦214926 . .
Supplementary Protector, Man Reset 3p 50a 250vac . . . . . . . . . . . . . . .
. . . 23 . . . . . . . . . . . . . +215347 . . . . Panel, Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . +♦215363 . . . . Panel, Generator Power (Full KVA Option) . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . CT2 . . ♦197433 . . . . Transformer, Current Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 24 . . . . . . . . . . . . ♦214927 . . . . Boot, Circuit Breaker 1 Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 25 . . . . . . . . . . . . ♦197508 . . . . Plug, Protective . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 26 . . . . . . . . . . . . ♦077440 . . . . Bushing, Conduit 1 In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 27 . . . . . . . . . . . . . . 601836 . . . . Nut, 250−20 .50hex .19h Brs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 010915 . . . . Washer, Flat .257idx0.640odx.031t Brs . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 163167 . . . . Washer, Lock .254idx0.489odx.062t Sst Split.250 . . . . . . . . . . . . . . . . .
. . . 28 . . . . GRD . . . . 083030 . . . . Stud, Brs .250−20 X 1.750 W/Hex Collar . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 29 . . . . . . . . . . . . ♦209056 . . . . Cover, Receptacle W/Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 30 . . . . . . . . . . . . . . 190861 . . . . Label, Warning Electric Shock And Moving Parts Etc . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . ♦197399 . . . . Label, Warning 3 Ph Generator Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 31 . . . . . . . . . . . . . . 209056 . . . . Cover, Receptacle 2.250 Dia. Lexan . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 32 . . . . . . . . . . . . ♦210149 . . Label, Battery Charge (Switch Position) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . ♦ . . Label, Polarity/AC Switch Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 33 . . . . . S12 . . ♦220491 . . Switch, Polarity/AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . S13 . . ♦210217 . . Switch, Battery Charge Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 34 . . . . . . . . . . . . . . 201125 . . Panel, Mtg Terminal Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 35 . . PC4, PC5 . . 189744 . . Circuit Card Assembly, HF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 36 . . . . . . . . . . . . ♦210206 . . Bracket, Support Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 37 . . . . . . . . . . . . . . 039046 . . Terminal, Pwr Output Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 180735 . . Washer, Output Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 38 . . . . . . . . . . . . . . 134201 . . Stand−off Support, Pc Card .312/.375w/Post&lock .43 . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
3
1
1
1
1
1
1
1
3
4
2
1
1
1
1
2
1
1
1
1
1
2
1
1
2
8
OM-4409 Page 91
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-3. Panel, Front w/Components (Continued)
. . . 39 . . . . . . . . . . . . . . 181169
. . . 40 . . . . . . . . . . . . . . 186621
. . . 41 . . . . . . . . . . . . ♦059773
. . . 42 . . . . . . . . . . . . ♦010647
. . . . . . . . . . . . . . . . . . ♦059773
. . . . . . . . . . . . . . . . . . ♦010647
. . . . . . . . . . . . . . . . . . ♦081499
. . . 43 . . . . . . . . . . . . . . 039047
. . . 44 . . . . . . . . . . . . . . 021385
. . . 45 . . . . . . . . . . . . . . 190323
. . . 46 . . . . . . . . . . . . . . 170391
. . . 47 . . FUEL/HM . . 232112
. . . 48 . . . . BAT . . . . 193228
. . . 49 . . . . . AIR . . . . 206599
. . . 50 . . . . TEMP . . . 217084
. . . 51 . . . . . OIL . . . . . 217083
. . . 52 . . . . . A1 . . . ♦164873
. . . 53 . . . . CT3 . . ♦209274
. . . 54 . . . . . V1 . . . ♦164874
. . . 55 . . . . . . . . . . . . . . 097922
. . . 56 . . . . . . . . . . . . . . 189161
. . . 57 . . . . . . . . . . . . . . 010647
. . . 58 . . . . . . . . . . . . . . 097924
. . . . . . . . . . . . . . . . . . . . 072590
. . . . . . . . . . . . . . . . . . . . 215207
. . . . . . . . . . PLG6 . . . . 114063
. . . . . . . . . . PLG8 . . . . 193184
. . . . . . . . . . . . . . . . . . . . 147992
. . . . . . . . . PLG13 . . . 158465
. . . . . . . . . . . . . . . . . . . . 088731
. . . . . . . . . . . . . . . . . . . . 135873
. . . . . . . . . . . . . . . . . . . . 187654
. . . . . . . . . . . . . . . . . . . . 196602
. . . . . . . . . . . . . . . . . . . . 059712
. . . . . . . . . . . . . . . . . . . . 024103
. . . . . . . . . . . . . . . . . . . . 120304
. . . . . . . . . . . . . . . . . . . . 025234
. . Spacer, Output Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Boot, Generic Output Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Switch, Handle (Polarity/AC Switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pin (Polarity/AC Switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Handle, Switch (Battery Charging) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pin,Spring Cs .156 X 1.250 (Battery Charging) . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Strip Terminal (Battery Charging) . . . . . . . . . . . . . . . . . . . . . .
. . Terminal, Pwr Output Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Boot, Toggle Switch Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Boot, Circuit Breaker Clear Hex Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Conn, Circ Ms Protective Cap Size 20 Nylon . . . . . . . . . . . . . . . . . . . . . . .
. . Gauge, Fuel Elec/Hour Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Meter, Volt DC 8 − 18 Scale 2.250 In Black Face . . . . . . . . . . . . . . . . . . . .
. . Gauge, Pressure 0−200 Psi Electric Switch . . . . . . . . . . . . . . . . . . . . . . . .
. . Gauge, Engine Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Gauge, Engine Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Meter, Amp AC/DC 0− 500 0−600 Dc Scale 2.5 In . . . . . . . . . . . . . . . . . . .
. . Xfmr, Current (Meters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Meter, Volt AC/DC 0− 100 Scale 2.5 In . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Knob, Pointer .875 Dia X .250 Id W/Set Screwsplstc . . . . . . . . . . . . . . . . .
. . Handle, Switch Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pin, Spring Cs .156 X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Knob, Pointer 1.625 Dia X .250 Id W/Set Screwsplstc . . . . . . . . . . . . . . . .
. . Lock, Shaft Pot .375−32 X .250 Dia Shaft Tall . . . . . . . . . . . . . . . . . . . . . . .
. . Harness, Unit Weld Control − CV (includes) . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Conn, Rect Univ 084 4p/S 1row Plug Cable Lkg . . . . . . . . . . . . . . . . . . .
. . . . Conn, Rect Cinch 30 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Conn, Rect Univ 039 10p/S 2row Plug Cable Lkg . . . . . . . . . . . . . . . . . .
. . . . Conn, Rect Univ 084 12p/S 3row Plug Cable Lkg . . . . . . . . . . . . . . . . . .
. . . . Bushing, Snap−in Nyl .375 Id X .500 Mtg Hole . . . . . . . . . . . . . . . . . . . .
. . . . Clip, Conduit Convoluted 1/2 In 6.35mm Mtg Hole . . . . . . . . . . . . . . . . .
. . . . Seal, Wire Univ 12p/S 3row . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Plug, Cavity 18,30 Position Cinch Connector . . . . . . . . . . . . . . . . . . . . . .
. . Clip, Component .437 Dia Mtg Adh Back . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Blank, Snap−in Nyl .750 Mtg Hole Black . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Blank, Snap−in Nyl .250 Mtg Hole Black . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Plug, Str Grd 2p3w 15a 250v *6−15p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
7
1
1
2
1
♦Optional
+
When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4409 Page 92
3
1
2
4
5
6
10
9
8
7
805 259-A
Figure 19-4. Auxiliary Power Group, Export
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-4. Auxiliary Power Group, Export
. . . 1 . . . . . . . . . . . . +223121 . . Panel, Aux Power (Export) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 2 . . . . . . . . . . . . . 144844 . . Stand−off, No 6−32 X .875 Lg .250 Hex Al Fem . . . . . . . . . . . . . . . . . . . . . 2
. . . 3 . . . ELCB1 . . 222991 . . Circuit Breaker, Elcb 20a 220v 0.030a Trip . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . . . . . . . . 200910 . . Label, Warning Electric Shock And Moving Parts Ce . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . 223132 . . Harness, Receptacle Auxillary Power W/Elcb (includes) . . . . . . . . . . . . . . .
. . . 5 . . . GFCI1 . . 151981 . . . . Rcpt, Str Dx Grd 2p3w 15/20a 125v *5−20r Gfi . . . . . . . . . . . . . . . . . . . . 1
. . . 6 . . . . CB2 . . . 093996 . . . . Circuit Breaker, Man Reset 1p 20a 250vac Frict . . . . . . . . . . . . . . . . . . . 1
. . . 7 . . . . . . . . . . . . . 083030 . . Stud, Brs .250−20 X 1.750 W/Hex Collar . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . 601836 . . Nut, 250−20 .50hex .19h Brs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . 8 . . . . . . . . . . . . . 190323 . . Boot, Circuit Breaker Clear Hex Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 9 . . . . . . . . . . . . . 209056 . . Cover, Receptacle W/Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 10 . . . . RC1 . . . 176355 . . Rcpt, Str 2p3w 16a 220v Flange Mtg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4409 Page 93
11
14
15
10
12
13
17
16
9
18
8
19
20
7
6
5
3
21
4
1
2
27
26
25
24
23
22
28
30
33
32
29
31
803 327
Figure 19-5. Generator
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-5. Generator (Figure 19-1 Item 112)
. . . 1 . . . . . . . . . . . . . . 132053 . . Screw, 375−16x1.50 Hex Hd−pln Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 2 . . . . . . . . . . . . . . 183387 . . Washer, Cone .380idx .860odx.109t Stl Pld 4000lbs . . . . . . . . . . . . . . . . .
. . . 3 . . . . . . . . . . . . . . 195911 . . Endbell, Gen (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 4 . . . . . . . . . . . . . . 143220 . . . . O-Ring 2.859 ID X .139 Cs 70 Duro Viton . . . . . . . . . . . . . . . . . . . . . . . .
. . . 5 . AUX STATOR . 201099 . . Stator, Exciter/Aux Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 6 . . . STATOR . . +208287 . . Stator, Weld Assy Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . STATOR +♦209220 . . Stator, Weld Assy Complete (3-Phase Generator Option) . . . . . . . . . . . . .
. . . 7 . . . . . . . . . . . . . . 225120 . . Label, Warning Moving Parts Can Cause Serious . . . . . . . . . . . . . . . . . . .
. . . 8 . . . . . . . . . . . . . . 190197 . . Guard, Generator Wire Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 9 . . . . . . . . . . . . . . 172674 . . Spring, Ext .240 Od X .041 Wire X 3.500 Pld . . . . . . . . . . . . . . . . . . . . . . .
. . . 10 . . . . . . . . . . . . . . 039207 . . Baffle, Air Gen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 11 . . . ROTOR . . . 212997 . . Rotor, Generator (Includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 12 . . . . . . . . . . . . . . 024617 . . . . Ring, Rtng Ext 1.375 Shaft X .050 Thk . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 13 . . . . . . . . . . . . . . 053390 . . . . Bearing, Ball Rdl Sgl Row 1.370 X 2.830 X .6 . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 210447 . . . . Fan, Rotor Assy Generator (Segmented) (includes) . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hub, Drive (Not Sold Separately) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 14 . . . . . . . . . . . . . . 210332 . . . . . . Plate, Flex Hubmount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 15 . . . . . . . . . . . . . . 206242 . . . . . . Fan, Rotor Segmented Assy Gen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 16 . . . . . . . . . . . . . . 049026 . . . . . . Screw, M10−1.5x 25 Hex Hd−pln 8.8 Pln . . . . . . . . . . . . . . . . . . . . . . . .
. . . 17 . . . . . . . . . . . . . . 083883 . . . . . . Washer, Lock .402idx0.709odx.087t Stl Split10mm . . . . . . . . . . . . . . .
. . . 18 . . . . . . . . . . . . . . 080389 . . . . . . Screw, 312−18x1.00 Hexwhd.66d Stl Pld Slffmg Tap−rw . . . . . . . . . .
. . . 19 . . . . . . . . . . . . . . 083883 . . Washer, Lock .402idx0.709odx.087t Stl Split10mm . . . . . . . . . . . . . . . . . .
. . . 20 . . . . . . . . . . . . . . 049026 . . Screw, M10−1.5x 25 Hex Hd−pln 8.8 Pln . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 21 . . . . . . . . . . . . . . 191579 . . Cover, Starter Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 22 . . . . . . . . . . . . . . 083883 . . Washer, Lock .402idx0.709odx.087t Stl Split10mm . . . . . . . . . . . . . . . . . .
OM-4409 Page 94
6
6
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
4
10
10
8
4
4
1
6
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-5. Generator (Continued)
...
...
...
...
...
...
...
...
...
...
...
23
24
25
26
27
28
29
30
31
32
33
. . . . . . . . . . . . . . 172555
. . . . . . . . . . . . . . 602159
. . . . . . . . . . . . . . 604950
. . . . . . . . . . . . . . 602211
. . . . . . . . . . . . . . 139341
. . . . . . . . . . . . . *190823
. . . . . . . . . . . . . . 188560
. . . . . . . . . . . . . . 189142
. . . . . . . . . . . . . . 602242
. . . . . . . . . . . . . . 602211
. . . . . . . . . . . . . . 604534
..
..
..
..
..
..
..
..
..
..
..
Screw, M10−1.5x 50 Hex Hd−pln 8.8 Pld . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screw, 312−18x .75 Hexwhd.66d Stl Pld Slffmg Tap−rw . . . . . . . . . . . . . .
Screw, 312−18x2.00 Hex Hd−pln Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . .
Washer, Lock .318idx0.586odx.078t Stl Pld Split.312 . . . . . . . . . . . . . . . .
Washer, Exciter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brush, Contact Elect .250 X.500 X 1.250 Grd Ay . . . . . . . . . . . . . . . . . . . .
Clip, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brushholder Assy, Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Washer, Flat .375idx0.875odx.083t Stl Pld . . . . . . . . . . . . . . . . . . . . . . . . .
Washer, Lock .318idx0.586odx.078t Stl Pld Split.312 . . . . . . . . . . . . . . . .
Screw, 312−18x1.25 Hex Hd−pln Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
4
4
4
3
3
1
2
2
2
+ When ordering a component originally displaying a precautionary label, the label should also be ordered.
*Recommended Spare Parts.
♦Optional
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4409 Page 95
Hardware is common and
not available unless listed.
4
3
2
1
5
6
7
8
9
802 279-A
Figure 19-6. Main Rectifier Assembly
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-6. Main Rectifier Assembly (Figure 19-1 Item 146)
. . . . . . . . . . SR3 . . . .
... 1 ..............
... 2 ..............
... 3 ..............
... 4 ..............
. . . 5 . . . . PC3 . . . .
... 6 ..............
... 7 ..............
. . . 8 . D3, D5, D7 .
. . . 9 . D2, D4, D6 .
239784
188137
188517
188135
134201
215755
188136
188493
238647
238649
. . Rectifier, environmental high power (includes) . . . . . . . . . . . . . . . . . . . . . .
. . . . Connection Board, Rectifier Ac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Bus Bar, Conn Bd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Enclosure, Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Stand−off Support, Pc Card .312/.375w/Post&lock .43 . . . . . . . . . . . . .
. . . . Circuit Card Assy, Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Insulator, Heatsink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Heat Sink, Rectifier Al . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Diode, Rect 400. A 800v Sp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Diode, Rect 400. A 800v Rp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
3
2
3
1
8
2
3
3
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4409 Page 96
Hardware is common and
not available unless listed.
53
79
80
10 9
54
51
56
57
13
19
17
13
10
9
2
20
22
23
16
15
11
14
11
58
45
46
59
47
44
28
43
8
7 6
4
82
41
3
4
39
42
86
40
85
84
62
63
29
26
75
45
81
83
27
5
76
64
38
32
78
4
26
31
9
60
89
25
6
12
61
48
24
1
77
55
50
49
21
9
9
18
34
33
87
88
65
66
67
37
35
36
68
72
70
69
74
73
71
4
803 328−G
Figure 19-7. Air Compressor Assembly
OM-4409 Page 97
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-7. Air Compressor Assembly (Figure 19-1 Items 51 & 78)
. . . 1 . . . . . . . . . . . . . . 206607 . . Valve, Ball . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 2 . . . . . . . . . . . . . . 210523 . . Ftg, Flrd Stl Tube End/Female Pipe End 3/4 . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 3 . . . . . . . . . . . . . . 206939 . . Tank, Oil Separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . . . . . . . . . 210248 . . Hose Assy, Air W/Fittings 3/4 X 35.250 Lg . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 5 . . . . . . . . . . . . . . 084999 . . Ftg, Pipe Brs Elbow St 45 1/4 Npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 6 . . . . . . . . . . . . . . 117826 . . Ftg, Pipe Brs Nipple Close 1/4 Npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 7 . . . . . . . . . . . . . . 210053 . . Valve, Pressure Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 8 . . . . . . . . . . . . . . 071270 . . Ftg, Pipe Brs Tee St 1/4 Npt 071 269 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 9 . . . . . . . . . . . . . . 209854 . . Ftg, Pipe Adapter M 1/4 Npt X 1/4 Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 10 . . . . . . . . . . . . . . 218602 . . Hose, Nylon Blue 44.000lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 11 . . . . . . . . . . . . . . 210040 . . Orifice/Muffler,120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 12 . . . . . . . . . . . . . . 151662 . . Ftg, Pipe Brs Plug Hex .125 Npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 13 . . . . . . . . . . . . . . 218601 . . Hose, Nylon Red 36.000lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 14 . . . . . . . . . . . . . . 210054 . . Valve, Automatic Blowdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 15 . . . . . . . . . . . . . . 206746 . . Switch, Pressure 20psi Nc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 16 . . . . . . . . . . . . . . 602965 . . Ftg, Pipe Brs Tee 1/8 Npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 17 . . . . . . . . . . . . . . 209635 . . Hose, Assy w/Fittings 42.360lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 18 . . . . . . . . . . . . . . 209621 . . Ftg, Stl Adapter 3/4 Sae−3/4 Jic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 19 . . . . . . . . . . . . . . 210051 . . Valve, Check Minimum Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 20 . . . . . . . . . . . . . . 209767 . . Ftg, Pipe Stl Connector M 3/4 Sae−npt Adapter . . . . . . . . . . . . . . . . . . . . . 1
. . . 21 . . . . . . . . . . . . . . 206615 . . Sender, Pressure Oil 0− 200 Psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 22 . . . . . . . . . . . . . . 073655 . . Ftg, Pipe Brs Nipple Hex 1/8 Npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 23 . . . . . . . . . . . . . . 206937 . . Manifold, Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 24 . . . . . . . . . . . . . . 206743 . . Valve, Safety Relief 150psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 25 . . . . . . . . . . . . . . 209754 . . Ftg, Pipe Stl Elbow M 45dg 3/4 X (Npt−jic 45dg) . . . . . . . . . . . . . . . . . . . . 1
. . . 26 . . . . . . . . . . . . . . 214685 . . Hose Assy, Air W/Fittings 3/4 X 21.750 Lg . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 27 . . . . . . . . . . . . . . 209787 . . Ftg, Pipe Stl Nipple Close 3/4 Npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 28 . . . . . . . . . . . . . . 209621 . . Fitting, Stl Adapter 3/4 SAE − 3/4 JIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 29 . . . . . . . . . . . . . . 210058 . . Gauge, Oil Level Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 30 . . . . . . . . . . . . . . Deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 31 . . . . . . . . . . . . . . 209766 . . Ftg, Pipe Stl Tee Street 3/4 Npt M−f−f . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 32 . . . . . . . . . . . . . . 209457 . . Ftg, Pipe Stl Elbow St 3/4 Npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 33 . . . . . . . . . . . . . . 209638 . . Hose, Oil W/Fittings 25.670 Lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 34 . . . . . . . . . . . . . . 209639 . . Hose, Oil W/Fittings 26.320 Lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 35 . . . . . . . . . . . . . . 210254 . . Bracket, Mtg Tbg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 36 . . . . . . . . . . . . . . 210251 . . Ftg, Stl Swivel Straight Thread Conn 3/4 O−ring . . . . . . . . . . . . . . . . . . . . . 1
. . . 37 . . . . . . . . . . . . . . 210252 . . Ftg, Stl Bulkhead Branch Tee 3/4 Flare Tube End . . . . . . . . . . . . . . . . . . . . 1
. . . 38 . . . . . . . . . . . . . . 210250 . . Hose Assy, Oil W/Fittings 3/4 X 15.500 Lg . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 39 . . . . . . . . . . . . . . 209765 . . Ftg, Pipe Stl Elbow Adapter 90dg 3/4 Sae−jic− . . . . . . . . . . . . . . . . . . . . . . 1
. . . 40 . . . . . . . . . . . . . . 208040 . . Tensioner,Belt w/Pully . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 41 . . . . . . . . . . . . . . 208428 . . Idler Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 42 . . . . . . . . . . . . . . 225038 . . Bracket, Mtg Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 43 . . . . . . . . . . . . . . 206742 . . Switch, High Air Temperature 248f Nc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . 210022 . . O−ring, High Air Temp Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 44 . . . . . . . . . . . . . . 211904 . . Manifold, Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . 218558 . . Screw, M 8−1.2x 50 Hex Hd−pln 8.8 Pld (Manifold Mtg.Screws) . . . . . . . 4
. . . 45 . . . . . . . . . . . . . . 209641 . . Hose, Nylon White 32.000lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 46 . . . . . . . . . . . . . . 209855 . . Ftg, Pipe Stl Adapter M 1/8 Npt X 1/4 Line . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 47 . . . . . . . . . . . . . . 015732 . . Ftg, Pipe Brs Elbow St 45 1/8 Npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 48 . . . . . . . . . . . . . . 209852 . . Ftg, Pipe Stl Adapter M M10 X 1/8 Npt F . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 49 . . . . . . . . . . . . . . 225005 . . Brace, Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 50 . . . . . . . . . . . . . . 084999 . . Ftg, Pipe Brs Elbow St 45 1/4 NPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 51 . . . . . . . . . . . . . . 176518 . . Ftg, Pipe Brs Elbow St 1/4 Npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 52 . . . . . . . . . . . . . . . . . . . . . . . . Deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-4409 Page 98
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 19-7. Air Compressor Assembly (Continued)
. . . 53 . . . . . . . . . . . . . . 206698
. . . 54 . . . . . . . . . . . . . . 218305
. . . . . . . . . . . . . . . . . . . . 210016
. . . 55 . . CLUTCH . . 210055
. . . 56 . . . . . . . . . . . . . . 218609
. . . 57 . . . . . . . . . . . . . . 206800
. . . 58 . . . . . . . . . . . . . . 210001
. . . 59 . . . . . . . . . . . . . . 209853
. . . 60 . . . . . . . . . . . . . . 209634
. . . 61 . . . . . . . . . . . . . . 206558
. . . 62 . . . . . . . . . . . . . . 209851
. . . 63 . . . . . . . . . . . . . . 209825
. . . 64 . . . . . . . . . . . . . . 209764
. . . 65 . . . . . . . . . . . . . . 209828
. . . 66 . . . . . . . . . . . . . . 209621
. . . 67 . . . . . . . . . . . . . . 210052
. . . 68 . . . . . . . . . . . . . . 206744
. . . 69 . . . . . . . . . . . . . . 206745
. . . 70 . . . . . . . . . . . . . . 209756
. . . 71 . . . . . . . . . . . . . . 214686
. . . 72 . . . . . . . . . . . . . . 210023
. . . 73 . . . . . . . . . . . . . . 206747
. . . 74 . . . . . . . . . . . . . . 208029
. . . 75 . . . . . . . . . . . . . . 209646
. . . 76 . . . . . . . . . . . . . . 209856
. . . 77 . . . . . . . . . . . . . . 210027
. . . 78 . . . . . . . . . . . . . . 209755
. . . . . . . . . . . . . . . . . . . *210056
. . . 79 . . . . . . . . . . . . . . 044772
. . . 80 . . . . . . . . . . . . . . 602216
. . . 81 . . . . . . . . . . . . . . 198447
. . . 82 . . . . . . . . . . . . . . 602243
. . . 83 . . . . . . . . . . . . . . 208425
. . . 84 . . . . . . . . . . . . . . 198631
. . . 85 . . . . . . . . . . . . . . 208426
. . . 86 . . . . . . . . . . . . . . 602216
. . . 87 . . . . . . . . . . . . . . 214687
. . . 88 . . . . . . . . . . . . . . 214920
. . . 89 . . . . . . . . . . . . . . 218423
. . Plate, Mtg Compressor To Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Valve, Inlet Unloader 90dg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Gasket, Unloader Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Clutch, Electro Magnetic 12vdc W/5.75 Dia Pulley . . . . . . . . . . . . . . . . . . .
. . Belt, Micro V 21mm X 1485mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pulley, Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Airend, Gear−driven W/Tapered Input Shaft . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Pipe Stl Adapter M M16 1.5 X 1/2 Jic . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Hose, Tubing Oil Assyw/Fittings 15.860lg . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cooler, Oil Engine/Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Pipe Stl Tube End Cap 3/4 0rfs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Stl Adapter Swivel 12m X Jic−12 F . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Pipe Stl Tee Branch Sae−12 X Jic−12 . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Stl Swivel Union Jic−12 F−f . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Stl Adapter 3/4 Sae−3/4 Jic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Valve,Oil Temperature Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Thermostat, 170f (w/gasket) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Filter, Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Pipe Stl Elbow M 90dg 1/2 Jic X 3/4 Sae . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Pipe Stl Elbow 90dg 3/4bspt M X 3/4 Jic M . . . . . . . . . . . . . . . . . . . . .
. . Filter, Separator Assembly (includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Separator, Oil/Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bracket, Mtg Filter Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Tubing, Ssstl .312 Od X.028 W/Ftgs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Stl Adapter Tube End Reducer 04f X 05m . . . . . . . . . . . . . . . . . . . . . .
. . Valve, Check/Scavenge Orifice/Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ftg, Pipe Stl Swivel F 1/4 Npt X 1/4 F Jic . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Oil, Compressor 1gal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Screw, M12−1.7x 30 Hex Hd−pln 8.8 Pln . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Lock .502idx0.879odx.151t Stl Pld Split.500 . . . . . . . . . . . . . . . . .
. . Screw, M10−1.5x 20 Hex Hd−pln 8.8 Pln . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Washer, Flat .438idx1.000odx.083t Stl Pld . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Screw, M10−1.5x 60 Hex Hd−pln 8.8 Pld Din 931 . . . . . . . . . . . . . . . . . . . .
. . Nut, M10 Hex Lock Nut Stl Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Screw, M12−1.75x 40 Hex Hd 12pt Flange Screw 12.9 . . . . . . . . . . . . . . .
. . Washer, Lock .502idx0.879odx.151t Stl Pld Split.500 . . . . . . . . . . . . . . . . .
. . Ftg, Pipe Stl 3/4bspp X 3/4 Jic M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Seal, Ring Bonded Rbr/Stl .950 Id X 1.380 Od X .100 . . . . . . . . . . . . . . . .
. . O-Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
6
1
1
1
1
2
2
1
1
1
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-4409 Page 99
Notes
WELD POSITION: FLAT
WELD JOINT
TYPES
HORIZONTAL
BUTT
1G
VERTICAL
BUTT
2G
FILLET
Ref. AWS/ANSI D1.1
OM-4409 Page 100
T−JOINT
1F
BUTT
4G
BUTT
3G
T−JOINT
2F
GROOVE
OVERHEAD
T−JOINT
4F
T−JOINT
3F
Ref. 804 248-A
Effective January 1, 2008
(Equipment with a serial number preface of LJ or newer)
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions
* Induction Heating Coils and Blankets, Cables, and
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to
Non-Electronic Controls
its original retail purchaser that new Miller equipment sold after
* APT & SAF Model Plasma Cutting Torches
the effective date of this limited warranty is free of defects in
* Remote Controls
material and workmanship at the time it is shipped by Miller. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
* Accessory (Kits)
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
* Replacement Parts (No labor)
WARRANTIES OF MERCHANTABILITY AND FITNESS.
* Spoolmate Spoolguns
Within the warranty periods listed below, Miller will repair or
* Canvas Covers
replace any warranted parts or components that fail due to such
defects in material or workmanship. Miller must be notified in
writing within thirty (30) days of such defect or failure, at which
time Miller will provide instructions on the warranty claim
procedures to be followed.
Miller shall honor warranty claims on warranted equipment listed
below in the event of such a failure within the warranty time
periods. All warranty time periods start on the delivery date of the
equipment to the original end-user purchaser, and not to exceed
one year after the equipment is shipped to a North American
distributor or eighteen months after the equipment is shipped to
an International distributor.
1.
2.
3.
4.
5.
5 Years Parts — 3 Years Labor
* Original main power rectifiers only to include SCRs,
diodes, and discrete rectifier modules
3 Years — Parts and Labor
* Transformer/Rectifier Power Sources
* Plasma Arc Cutting Power Sources
* Process Controllers
* Semi-Automatic and Automatic Wire Feeders
* Inverter Power Sources (Unless Otherwise Stated)
* Water Coolant Systems (Integrated)
* Intellitig
* Engine Driven Welding Generators
(NOTE: Engines are warranted separately by the
engine manufacturer.)
1 Year — Parts and Labor Unless Specified
* Motor Driven Guns (w/exception of Spoolmate
Spoolguns)
* Positioners and Controllers
* Automatic Motion Devices
* RFCS Foot Controls
* Induction Heating Power Sources, Coolers, and
Electronic
Controls/Recorders
* Water Coolant Systems (Non-Integrated)
* Flowgauge and Flowmeter Regulators (No Labor)
* HF Units
* Grids
* Spot Welders
* Load Banks
* Arc Stud Power Sources & Arc Stud Guns
* Racks
* Running Gear/Trailers
* Plasma Cutting Torches (except APT & SAF
Models)
* Field Options
(NOTE: Field options are covered under True Blue®
for the remaining warranty period of the product they
are installed in, or for a minimum of one year —
whichever is greater.)
* Bernard-Branded Mig Guns (No Labor)
* Weldcraft-Branded TIG Torches (No Labor)
* Subarc Wire Drive Assemblies
6 Months — Batteries
90 Days — Parts
* MIG Guns and Subarc (SAW) Guns
Miller’s True Blue® Limited Warranty shall not apply to:
1.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, slip rings,
relays or parts that fail due to normal wear.
(Exception: brushes, slip rings, and relays are
covered on Bobcat, Trailblazer, and Legend
models.)
2.
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
Equipment that has been modified by any party other
than Miller, or equipment that has been improperly
installed, improperly operated or misused based upon
industry standards, or equipment which has not had
reasonable and necessary maintenance, or equipment
which has been used for operation outside of the
specifications for the equipment.
3.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the goods at
customer’s risk and expense. Miller’s option of repair or
replacement will be F.O.B., Factory at Appleton, Wisconsin, or
F.O.B. at a Miller authorized service facility as determined by
Miller. Therefore no compensation or reimbursement for
transportation costs of any kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY
OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION
OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING,
INCLUDING
ANY
IMPLIED
WARRANTY
OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT
FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED
BY MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available,
but may vary from province to province.
miller_warr 2008-01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
PRINTED IN USA
© 2008 Miller Electric Mfg. Co. 2008−01
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
European Headquarters −
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
www.MillerWelds.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement