Miller EXTREME 360 MAP AUTO-LINE User manual

OM-237 881W
2015−07
Processes
Multiprocess Welding
Description
Arc Welding Power Source
EXTREME 360 MAP
Auto-Line
™
File: MULTIPROCESS
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Symboles utilisés . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance . . . . .
2-4. Proposition californienne 65 Avertissements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6. Informations relatives aux CEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Manufacturer Safety Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Miscellaneous Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Features And Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Arc Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Serial Number And Rating Label Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Dimensions And Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. Static Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Selecting a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Selecting Cable Sizes* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Weld Output Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Remote 14 Receptacle Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Optional 115 Volts AC Duplex Receptacle And Supplementary Protectors . . . . . . . . . . . . . . . . . . . . .
5-6. Optional Gas Valve Operation And Shielding Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Electrical Service Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8. Connecting 1-Phase Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-9. Connecting 3-Phase Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − GENERAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Mode Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. Configuration Option Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − GTAW OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Typical Connection For GTAW Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Scratch Start TIG Welding Mode - GTAW Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3. Lift-Arc TIG Welding Mode - GTAW Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4. TIG Welding Mode - GTAW Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
3
4
4
4
5
5
5
7
9
9
9
11
11
11
12
12
12
12
12
13
14
14
15
15
16
16
17
17
18
19
20
22
24
24
25
26
28
28
29
30
31
TABLE OF CONTENTS
SECTION 8 − GMAW/GMAW-P/FCAW OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1. Typical Connection For Remote Control Feeder GMAW/GMAW-P/FCAW Process . . . . . . . . . . . . . .
8-2. MIG Welding Mode - GMAW/FCAW Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-3. MIG - Wire and Gas Selection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-4. Pulsed MIG Welding Mode - GMAW-P Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-5. Pulsed MIG - Wire and Gas Selection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-6. Remote Process Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-7. Typical Connection For Voltage-Sensing Feeder GMAW/GMAW-P/FCAW Process . . . . . . . . . . . . . .
8-8. V-Sense Feeder Welding Mode - GMAW/FCAW Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-9. V-Sense Feeder Welding Mode - GMAW-P Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − SMAW/CAC-A OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-1. Typical Connection For SMAW And CAC-A Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-2. CC Welding Mode - SMAW/CAC-A Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-3. Stick Welding Mode - SMAW/CAC-A Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-4. Optional Low Open Circuit Voltage (OCV) Welding Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10 − MAINTENANCE & TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-2. Blowing Out Inside Of Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-3. Help Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-4. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 11 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY
COMPLETE PARTS LIST − Available at www.MillerWelds.com
32
32
34
35
36
37
38
39
40
41
42
42
43
44
45
46
46
46
47
48
50
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som 2013−09
7
Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.
1-1. Symbol Usage
DANGER! − Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in the text.
NOTICE − Indicates statements not related to personal injury.
Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the
hazards.
1-2. Arc Welding Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information
found in the Safety Standards listed in Section 1-5. Read and
follow all Safety Standards.
Only qualified persons should install, operate, maintain, and
repair this unit.
During operation, keep everybody, especially children, away.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic
wire welding, the wire, wire reel, drive roll housing,
and all metal parts touching the welding wire are
electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
Do not touch live electrical parts.
Wear dry, hole-free insulating gloves and body protection.
Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
Use AC output ONLY if required for the welding process.
If AC output is required, use remote output control if present on
unit.
Additional safety precautions are required when any of the following electrically hazardous conditions are present: in damp
locations or while wearing wet clothing; on metal structures such
as floors, gratings, or scaffolds; when in cramped positions such
as sitting, kneeling, or lying; or when there is a high risk of unavoidable or accidental contact with the workpiece or ground. For these
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone!
Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
Properly install, ground, and operate this equipment according to
its Owner’s Manual and national, state, and local codes.
Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
When making input connections, attach proper grounding conductor first − double-check connections.
Keep cords dry, free of oil and grease, and protected from hot metal
and sparks.
Frequently inspect input power cord and ground conductor for
damage or bare wiring – replace immediately if damaged – bare
wiring can kill.
Turn off all equipment when not in use.
Do not use worn, damaged, undersized, or repaired cables.
Do not drape cables over your body.
If earth grounding of the workpiece is required, ground it directly
with a separate cable.
Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
Do not touch electrode holders connected to two welding machines at the same time since double open-circuit voltage will be
present.
Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
Wear a safety harness if working above floor level.
Keep all panels and covers securely in place.
Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
Do not connect more than one electrode or work cable to any
single weld output terminal. Disconnect cable for process not in
use.
Use GFCI protection when operating auxiliary equipment in damp
or wet locations.
SIGNIFICANT DC VOLTAGE exists in inverter welding power sources AFTER removal of input power.
Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
HOT PARTS can burn.
Do not touch hot parts bare handed.
Allow cooling period before working on equipment.
To handle hot parts, use proper tools and/or
wear heavy, insulated welding gloves and
clothing to prevent burns.
OM-237 881 Page 1
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
Keep your head out of the fumes. Do not breathe the fumes.
If inside, ventilate the area and/or use local forced ventilation at the
arc to remove welding fumes and gases. The recommended way
to determine adequate ventilation is to sample for the composition
and quantity of fumes and gases to which personnel are exposed.
If ventilation is poor, wear an approved air-supplied respirator.
Read and understand the Safety Data Sheets (SDSs) and the
manufacturer’s instructions for adhesives, coatings, cleaners,
consumables, coolants, degreasers, fluxes, and metals.
Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements
can give off toxic fumes if welded.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
Wear an approved welding helmet fitted with a proper shade of
filter lenses to protect your face and eyes from arc rays and
sparks when welding or watching (see ANSI Z49.1 and Z87.1
listed in Safety Standards).
Wear approved safety glasses with side shields under your
helmet.
Use protective screens or barriers to protect others from flash,
glare and sparks; warn others not to watch the arc.
Wear body protection made from durable, flame−resistant material (leather, heavy cotton, wool). Body protection includes
oil-free clothing such as leather gloves, heavy shirt, cuffless
trousers, high shoes, and a cap.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
Do not weld where flying sparks can strike flammable material.
Protect yourself and others from flying sparks and hot metal.
Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
Watch for fire, and keep a fire extinguisher nearby.
Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
Do not weld on containers that have held combustibles, or on
closed containers such as tanks, drums, or pipes unless they are
properly prepared according to AWS F4.1 and AWS A6.0 (see
Safety Standards).
Do not weld where the atmosphere may contain flammable dust,
gas, or liquid vapors (such as gasoline).
Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock, sparks, and fire
hazards.
Do not use welder to thaw frozen pipes.
OM-237 881 Page 2
Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
Wear body protection made from durable, flame−resistant material
(leather, heavy cotton, wool). Body protection includes oil-free
clothing such as leather gloves, heavy shirt, cuffless trousers, high
shoes, and a cap.
Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
After completion of work, inspect area to ensure it is free of sparks,
glowing embers, and flames.
Use only correct fuses or circuit breakers. Do not oversize or bypass them.
Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
for hot work and have a fire watcher and extinguisher nearby.
Read and understand the Safety Data Sheets (SDSs) and the
manufacturer s instructions for adhesives, coatings, cleaners,
consumables, coolants, degreasers, fluxes, and metals.
FLYING METAL or DIRT can injure eyes.
Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
Wear approved safety glasses with side
shields even under your welding helmet.
BUILDUP OF GAS can injure or kill.
Shut off compressed gas supply when not in use.
Always ventilate confined spaces or use
approved air-supplied respirator.
ELECTRIC AND MAGNETIC FIELDS (EMF)
can affect Implanted Medical Devices.
Wearers of Pacemakers and other Implanted
Medical Devices should keep away.
Implanted Medical Device wearers should consult their doctor
and the device manufacturer before going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating
operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
Wear approved ear protection if noise level is high.
CYLINDERS can explode if damaged.
Compressed gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
Protect compressed gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open flames, sparks, and arcs.
Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
Keep cylinders away from any welding or other electrical circuits.
Never drape a welding torch over a gas cylinder.
Never allow a welding electrode to touch any cylinder.
Never weld on a pressurized cylinder − explosion will result.
Use only correct compressed gas cylinders, regulators, hoses,
and fittings designed for the specific application; maintain them
and associated parts in good condition.
Turn face away from valve outlet when opening cylinder valve. Do
not stand in front of or behind the regulator when opening the valve.
Keep protective cap in place over valve except when cylinder is in
use or connected for use.
Use the right equipment, correct procedures, and sufficient number of persons to lift and move cylinders.
Read and follow instructions on compressed gas cylinders,
associated equipment, and Compressed Gas Association (CGA)
publication P-1 listed in Safety Standards.
1-3. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
Do not install or place unit on, over, or near
combustible surfaces.
Do not install unit near flammables.
Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
FALLING EQUIPMENT can injure.
Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
Use equipment of adequate capacity to lift and
support unit.
If using lift forks to move unit, be sure forks are long enough to
extend beyond opposite side of unit.
Keep equipment (cables and cords) away from moving vehicles
when working from an aerial location.
Follow the guidelines in the Applications Manual for the Revised
NIOSH Lifting Equation (Publication No. 94−110) when manually lifting heavy parts or equipment.
OVERUSE can cause OVERHEATING
MOVING PARTS can injure.
Keep away from moving parts such as fans.
Keep all doors, panels, covers, and guards
closed and securely in place.
Have only qualified persons remove doors, panels, covers, or
guards for maintenance and troubleshooting as necessary.
Reinstall doors, panels, covers, or guards when maintenance is
finished and before reconnecting input power.
READ INSTRUCTIONS.
Read and follow all labels and the Owner’s
Manual carefully before installing, operating, or
servicing unit. Read the safety information at
the beginning of the manual and in each
section.
Use only genuine replacement parts from the manufacturer.
Perform maintenance and service according to the Owner’s
Manuals, industry standards, and national, state, and local
codes.
Allow cooling period; follow rated duty cycle.
Reduce current or reduce duty cycle before
starting to weld again.
Do not block or filter airflow to unit.
H.F. RADIATION can cause interference.
FLYING SPARKS can injure.
Wear a face shield to protect eyes and face.
Shape tungsten electrode only on grinder with
proper guards in a safe location wearing proper
face, hand, and body protection.
Sparks can cause fires — keep flammables away.
STATIC (ESD) can damage PC boards.
Put on grounded wrist strap BEFORE handling
boards or parts.
Use proper static-proof bags and boxes to
store, move, or ship PC boards.
High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
MOVING PARTS can injure.
ARC WELDING can cause interference.
Keep away from moving parts.
Keep away from pinch points such as drive
rolls.
WELDING WIRE can injure.
Do not press gun trigger until instructed to do
so.
Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
BATTERY EXPLOSION can injure.
Do not use welder to charge batteries or jump
start vehicles unless it has a battery charging
feature designed for this purpose.
Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
OM-237 881 Page 3
1-4. California Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to
the state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after use.
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Combustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:
800-463-6727, website: www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website:
www.cdc.gov/NIOSH).
1-6. EMF Information
Electric current flowing through any conductor causes localized electric
and magnetic fields (EMF). The current from arc welding (and allied processes including spot welding, gouging, plasma arc cutting, and
induction heating operations) creates an EMF field around the welding
circuit. EMF fields may interfere with some medical implants, e.g. pacemakers. Protective measures for persons wearing medical implants
have to be taken. For example, restrict access for passers−by or conduct individual risk assessment for welders. All welders should use the
following procedures in order to minimize exposure to EMF fields from
the welding circuit:
1. Keep cables close together by twisting or taping them, or using a
cable cover.
2. Do not place your body between welding cables. Arrange cables
to one side and away from the operator.
3. Do not coil or drape cables around your body.
OM-237 881 Page 4
4. Keep head and trunk as far away from the equipment in the
welding circuit as possible.
5. Connect work clamp to workpiece as close to the weld as
possible.
6. Do not work next to, sit or lean on the welding power source.
7. Do not weld whilst carrying the welding power source or wire
feeder.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION
fre_som_2013−09
7
Pour écarter les risques de blessure pour vous−même et pour autrui — lire, appliquer et ranger en lieu sûr ces consignes relatives
aux précautions de sécurité et au mode opératoire.
2-1. Symboles utilisés
DANGER! − Indique une situation dangereuse qui si on
l’évite pas peut donner la mort ou des blessures graves.
Les dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
Indique une situation dangereuse qui si on l’évite pas
peut donner la mort ou des blessures graves. Les dangers possibles sont montrés par les symboles joints ou
sont expliqués dans le texte.
NOTE − Indique des déclarations pas en relation avec des blessures
personnelles.
Indique des instructions spécifiques.
Ce groupe de symboles veut dire Avertissement! Attention! DANGER
DE CHOC ELECTRIQUE, PIECES EN MOUVEMENT, et PIECES
CHAUDES. Consulter les symboles et les instructions ci-dessous y
afférant pour les actions nécessaires afin d’éviter le danger.
2-2. Dangers relatifs au soudage à l’arc
Les symboles représentés ci-dessous sont utilisés dans ce manuel pour attirer l’attention et identifier les dangers possibles. En
présence de l’un de ces symboles, prendre garde et suivre les
instructions afférentes pour éviter tout risque. Les instructions
en matière de sécurité indiquées ci-dessous ne constituent
qu’un sommaire des instructions de sécurité plus complètes
fournies dans les normes de sécurité énumérées dans la Section 2-5. Lire et observer toutes les normes de sécurité.
Seul un personnel qualifié est autorisé à installer, faire fonctionner, entretenir et réparer cet appareil.
Pendant le fonctionnement, maintenir à distance toutes les
personnes, notamment les enfants de l’appareil.
UNE DÉCHARGE ÉLECTRIQUE peut
entraîner la mort.
Le contact d’organes électriques sous tension peut
provoquer des accidents mortels ou des brûlures
graves. Le circuit de l’électrode et de la pièce est
sous tension lorsque le courant est délivré à la
sortie. Le circuit d’alimentation et les circuits internes de la machine sont également sous tension
lorsque l’alimentation est sur Marche. Dans le mode
de soudage avec du fil, le fil, le dérouleur, le bloc de
commande du rouleau et toutes les parties métalliques en contact avec le fil sont sous tension
électrique. Un équipement installé ou mis à la terre
de manière incorrecte ou impropre constitue un
danger.
Ne pas toucher aux pièces électriques sous tension.
Porter des gants isolants et des vêtements de protection secs et
sans trous.
S’isoler de la pièce à couper et du sol en utilisant des housses ou
des tapis assez grands afin d’éviter tout contact physique avec la
pièce à couper ou le sol.
Ne pas se servir de source électrique à courant électrique dans les
zones humides, dans les endroits confinés ou là où on risque de
tomber.
Se servir d’une source électrique à courant électrique UNIQUEMENT si le procédé de soudage le demande.
Si l’utilisation d’une source électrique à courant électrique s’avère
nécessaire, se servir de la fonction de télécommande si l’appareil
en est équipé.
D’autres consignes de sécurité sont nécessaires dans les conditions suivantes : risques électriques dans un environnement
humide ou si l’on porte des vêtements mouillés ; sur des structures
métalliques telles que sols, grilles ou échafaudages ; en position
coincée comme assise, à genoux ou couchée ; ou s’il y a un risque
élevé de contact inévitable ou accidentel avec la pièce à souder ou
le sol. Dans ces conditions, utiliser les équipements suivants,
dans l’ordre indiqué : 1) un poste à souder DC à tension constante
(à fil), 2) un poste à souder DC manuel (électrode) ou 3) un poste à
souder AC à tension à vide réduite. Dans la plupart des situations,
l’utilisation d’un poste à souder DC à fil à tension constante est recommandée. En outre, ne pas travailler seul !
Couper l’alimentation ou arrêter le moteur avant de procéder à l’installation, à la réparation ou à l’entretien de l’appareil. Déverrouiller
l’alimentation selon la norme OSHA 29 CFR 1910.147 (voir normes de sécurité).
Installez, mettez à la terre et utilisez correctement cet équipement
conformément à son Manuel d’Utilisation et aux réglementations
nationales, gouvernementales et locales.
Toujours vérifier la terre du cordon d’alimentation. Vérifier et
s’assurer que le fil de terre du cordon d’alimentation est bien
raccordé à la borne de terre du sectionneur ou que la fiche du
cordon est raccordée à une prise correctement mise à la terre.
En effectuant les raccordements d’entrée, fixer d’abord le conducteur de mise à la terre approprié et contre-vérifier les connexions.
Les câbles doivent être exempts d’humidité, d’huile et de graisse;
protégez−les contre les étincelles et les pièces métalliques
chaudes.
Vérifier fréquemment le cordon d’alimentation et le conducteur de
mise à la terre afin de s’assurer qu’il n’est pas altéré ou dénudé −,
le remplacer immédiatement s’il l’est −. Un fil dénudé peut entraîner la mort.
L’équipement doit être hors tension lorsqu’il n’est pas utilisé.
Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante ou mal épissés.
Ne pas enrouler les câbles autour du corps.
Si la pièce soudée doit être mise à la terre, le faire directement
avec un câble distinct.
Ne pas toucher l’électrode quand on est en contact avec la pièce,
la terre ou une électrode provenant d’une autre machine.
Ne pas toucher des porte électrodes connectés à deux machines
en même temps à cause de la présence d’une tension à vide doublée.
N’utiliser qu’un matériel en bon état. Réparer ou remplacer sur-lechamp les pièces endommagées. Entretenir l’appareil conformément à ce manuel.
Porter un harnais de sécurité si l’on doit travailler au-dessus du sol.
S’assurer que tous les panneaux et couvercles sont correctement
en place.
Fixer le câble de retour de façon à obtenir un bon contact métalmétal avec la pièce à souder ou la table de travail, le plus près possible de la soudure.
Isoler la pince de masse quand pas mis à la pièce pour éviter le
contact avec tout objet métallique.
OM-237 881 Page 5
Ne pas raccorder plus d’une électrode ou plus d’un câble de
masse à une même borne de sortie de soudage. Débrancher le
câble pour le procédé non utilisé.
Utiliser une protection différentielle lors de l’utilisation d’un équipement auxiliaire dans des endroits humides ou mouillés.
Il reste une TENSION DC NON NÉGLIGEABLE dans
les sources de soudage onduleur UNE FOIS
l’alimentation coupée.
Arrêter les convertisseurs, débrancher le courant électrique et
décharger les condensateurs d’alimentation selon les instructions
indiquées dans la partie Entretien avant de toucher les pièces.
LES PIÈCES CHAUDES peuvent
provoquer des brûlures.
Ne pas toucher à mains nues les parties
chaudes.
Prévoir une période de refroidissement avant de
travailler à l’équipement.
Ne pas toucher aux pièces chaudes, utiliser les
outils recommandés et porter des gants de soudage et des vêtements épais pour éviter les brûlures.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
Le soudage génère des fumées et des gaz. Leur
inhalation peut être dangereux pour votre santé.
Eloigner votre tête des fumées. Ne pas respirer les fumées.
À l’intérieur, ventiler la zone et/ou utiliser une ventilation forcée au
niveau de l’arc pour l’évacuation des fumées et des gaz de
soudage. Pour déterminer la bonne ventilation, il est recommandé
de procéder à un prélèvement pour la composition et la quantité
de fumées et de gaz auxquels est exposé le personnel.
Si la ventilation est médiocre, porter un respirateur anti-vapeurs
approuvé.
Lire et comprendre les fiches de données de sécurité et les instructions du fabricant concernant les adhésifs, les revêtements, les
nettoyants, les consommables, les produits de refroidissement, les
dégraisseurs, les flux et les métaux.
Travailler dans un espace fermé seulement s’il est bien ventilé ou
en portant un respirateur à alimentation d’air. Demander toujours à
un surveillant dûment formé de se tenir à proximité. Des fumées et
des gaz de soudage peuvent déplacer l’air et abaisser le niveau
d’oxygène provoquant des blessures ou des accidents mortels.
S’assurer que l’air de respiration ne présente aucun danger.
Ne pas souder dans des endroits situés à proximité d’opérations
de dégraissage, de nettoyage ou de pulvérisation. La chaleur et
les rayons de l’arc peuvent réagir en présence de vapeurs et former des gaz hautement toxiques et irritants.
Ne pas souder des métaux munis d’un revêtement, tels que l’acier
galvanisé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait été enlevé dans la zone de soudure, que l’endroit soit
bien ventilé, et en portant un respirateur à alimentation d’air. Les
revêtements et tous les métaux renfermant ces éléments peuvent
dégager des fumées toxiques en cas de soudage.
LES RAYONS DE L’ARC peuvent
provoquer des brûlures dans les
yeux et sur la peau.
Le rayonnement de l’arc du procédé de soudage
génère des rayons visibles et invisibles intenses
(ultraviolets et infrarouges) susceptibles de provoquer des brûlures
dans les yeux et sur la peau. Des étincelles sont projetées pendant le
soudage.
Porter un casque de soudage approuvé muni de verres filtrants
approprié pour protéger visage et yeux pour protéger votre visage
et vos yeux pendant le soudage ou pour regarder (voir ANSI Z49.1
et Z87.1 énuméré dans les normes de sécurité).
Porter des lunettes de sécurité avec écrans latéraux même sous
votre casque.
OM-237 881 Page 6
Avoir recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements les éblouissements
et les étincelles ; prévenir toute personne sur les lieux de ne pas
regarder l’arc.
Porter un équipement de protection pour le corps fait d’un matériau
résistant et ignifuge (cuir, coton robuste, laine). La protection du
corps comporte des vêtements sans huile comme par ex. des
gants de cuir, une chemise solide, des pantalons sans revers, des
chaussures hautes et une casquette.
LE SOUDAGE peut provoquer un
incendie ou une explosion.
Le soudage effectué sur des conteneurs fermés tels
que des réservoirs, tambours ou des conduites peut
provoquer leur éclatement. Des étincelles peuvent
être projetées de l’arc de soudure. La projection d’étincelles, des
pièces chaudes et des équipements chauds peut provoquer des
incendies et des brûlures. Le contact accidentel de l’électrode avec
des objets métalliques peut provoquer des étincelles, une explosion,
un surchauffement ou un incendie. Avant de commencer le soudage,
vérifier et s’assurer que l’endroit ne présente pas de danger.
Déplacer toutes les substances inflammables à une distance de
10,7 m de l’arc de soudage. En cas d’impossibilité les recouvrir
soigneusement avec des protections homologués.
Ne pas souder dans un endroit là où des étincelles peuvent tomber
sur des substances inflammables.
Se protéger et d’autres personnes de la projection d’étincelles et
de métal chaud.
Des étincelles et des matériaux chauds du soudage peuvent
facilement passer dans d’autres zones en traversant de petites
fissures et des ouvertures.
Surveiller tout déclenchement d’incendie et tenir un extincteur à
proximité.
Le soudage effectué sur un plafond, plancher, paroi ou séparation
peut déclencher un incendie de l’autre côté.
Ne pas effectuer le soudage sur des conteneurs fermés tels que
des réservoirs, tambours, ou conduites, à moins qu’ils n’aient été
préparés correctement conformément à AWS F4.1 et AWS A6.0
(voir les Normes de Sécurité).
Ne soudez pas si l’air ambiant est chargé de particules, gaz, ou vapeurs inflammables (vapeur d’essence, par exemple).
Brancher le câble de masse sur la pièce le plus près possible de la
zone de soudage pour éviter le transport du courant sur une
longue distance par des chemins inconnus éventuels en provoquant des risques d’électrocution, d’étincelles et d’incendie.
Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
En cas de non utilisation, enlever la baguette d’électrode du porteélectrode ou couper le fil à la pointe de contact.
Porter un équipement de protection pour le corps fait d’un matériau
résistant et ignifuge (cuir, coton robuste, laine). La protection du
corps comporte des vêtements sans huile comme par ex. des
gants de cuir, une chemise solide, des pantalons sans revers, des
chaussures hautes et une casquette.
Avant de souder, retirer toute substance combustible de vos poches telles qu’un allumeur au butane ou des allumettes.
Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
Suivre les recommandations dans OSHA 1910.252(a)(2)(iv) et
NFPA 51B pour les travaux à chaud et avoir de la surveillance et un
extincteur à proximité.
Lire et comprendre les fiches de données de sécurité et les instructions du fabricant concernant les adhésifs, les revêtements, les
nettoyants, les consommables, les produits de refroidissement,
les dégraisseurs, les flux et les métaux.
DES PIECES DE METAL ou DES
SALETES peuvent provoquer des
blessures dans les yeux.
Le soudage, l’écaillement, le passage de la
pièce à la brosse en fil de fer, et le meulage génèrent des étincelles et des particules
métalliques volantes. Pendant la période de
refroidissement des soudures, elles risquent
de projeter du laitier.
Porter des lunettes de sécurité avec écrans latéraux ou un écran
facial.
LES ACCUMULATIONS DE GAZ
risquent de provoquer des blessures
ou même la mort.
Fermer l’alimentation du gaz comprimé en cas
de non utilisation.
Veiller toujours à bien aérer les espaces confinés ou se servir d’un respirateur d’adduction
d’air homologué.
Les CHAMPS ÉLECTROMAGNÉTIQUES
(CEM) peuvent affecter les implants médicaux.
Les porteurs de stimulateurs cardiaques et
autres implants médicaux doivent rester à
distance.
Les porteurs d’implants médicaux doivent consulter leur
médecin et le fabricant du dispositif avant de s’approcher de la
zone où se déroule du soudage à l’arc, du soudage par points, du
gougeage, de la découpe plasma ou une opération de chauffage
par induction.
LE BRUIT peut endommager l’ouïe.
LES BOUTEILLES peuvent exploser
si elles sont endommagées.
Les bouteilles de gaz comprimé contiennent du gaz
sous haute pression. Si une bouteille est
endommagée, elle peut exploser. Du fait que les
bouteilles de gaz font normalement partie du
procédé de soudage, les manipuler avec
précaution.
Protéger les bouteilles de gaz comprimé d’une chaleur excessive, des chocs mécaniques, des dommages physiques, du laitier, des flammes ouvertes, des étincelles et des arcs.
Placer les bouteilles debout en les fixant dans un support stationnaire ou dans un porte-bouteilles pour les empêcher de tomber ou de se renverser.
Tenir les bouteilles éloignées des circuits de soudage ou autres
circuits électriques.
Ne jamais placer une torche de soudage sur une bouteille à gaz.
Une électrode de soudage ne doit jamais entrer en contact avec
une bouteille.
Ne jamais souder une bouteille pressurisée − risque d’explosion.
Utiliser seulement des bouteilles de gaz comprimé, régulateurs,
tuyaux et raccords convenables pour cette application
spécifique; les maintenir ainsi que les éléments associés en bon
état.
Tourner le dos à la sortie de vanne lors de l’ouverture de la vanne
de la bouteille. Ne pas se tenir devant ou derrière le régulateur
lors de l’ouverture de la vanne.
Le couvercle du détendeur doit toujours être en place, sauf lorsque la bouteille est utilisée ou qu’elle est reliée pour usage ultérieur.
Utiliser les équipements corrects, les bonnes procédures et suffisamment de personnes pour soulever et déplacer les bouteilles.
Lire et suivre les instructions sur les bouteilles de gaz comprimé,
l’équipement connexe et le dépliant P-1 de la CGA (Compressed
Gas Association) mentionné dans les principales normes de sécurité.
Le bruit des processus et des équipements peut
affecter l’ouïe.
Porter des protections approuvées pour les
oreilles si le niveau sonore est trop élevé.
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance
Risque D’INCENDIE OU
D’EXPLOSION.
Ne pas placer l’appareil sur, au-dessus ou
à proximité de surfaces inflammables.
Ne pas installer l’appareil à proximité de produits inflammables.
Ne pas surcharger l’installation électrique − s’assurer que
l’alimentation est correctement dimensionnée et protégée avant
de mettre l’appareil en service.
LA CHUTE DE L’ÉQUIPEMENT peut
provoquer des blessures.
Utiliser l’anneau de levage uniquement pour
soulever l’appareil, NON PAS les chariots, les
bouteilles de gaz ou tout autre accessoire.
Utiliser un équipement de levage de capacité suffisante pour lever
l’appareil.
En utilisant des fourches de levage pour déplacer l’unité, s’assurer
que les fourches sont suffisamment longues pour dépasser du
côté opposé de l’appareil.
Tenir l’équipement (câbles et cordons) à distance des véhicules
mobiles lors de toute opération en hauteur.
Suivre les consignes du Manuel des applications pour l’équation
de levage NIOSH révisée (Publication Nº94–110) lors du levage
manuelle de pièces ou équipements lourds.
L’EMPLOI EXCESSIF peut
SURCHAUFFER L’ÉQUIPEMENT.
Prévoir une période de refroidissement ; respecter le cycle opératoire nominal.
Réduire le courant ou le facteur de marche
avant de poursuivre le soudage.
Ne pas obstruer les passages d’air du poste.
LES ÉTINCELLES PROJETÉES
peuvent provoquer des blessures.
Porter un écran facial pour protéger le visage et
les yeux.
Affûter l’électrode au tungstène uniquement à la
meuleuse dotée de protecteurs. Cette
manœuvre est à exécuter dans un endroit sûr
lorsque l’on porte l’équipement homologué de
protection du visage, des mains et du corps.
Les étincelles risquent de causer un incendie − éloigner toute substance inflammable.
OM-237 881 Page 7
LES CHARGES ÉLECTROSTATIQUES peuvent endommager les circuits imprimés.
LE
RAYONNEMENT
HAUTE
FRÉQUENCE
(H.F.)
risque
de
provoquer des interférences.
Établir la connexion avec la barrette de terre
avant de manipuler des cartes ou des pièces.
Utiliser des pochettes et des boîtes antistatiques pour stocker, déplacer ou expédier des
cartes de circuits imprimes.
Les PIÈCES MOBILES peuvent
causer des blessures.
Ne pas s’approcher des organes mobiles.
Ne pas s’approcher des points de coincement
tels que des rouleaux de commande.
LES FILS DE SOUDAGE peuvent
provoquer des blessures.
Ne pas appuyer sur la gâchette avant d’en
avoir reçu l’instruction.
Ne pas diriger le pistolet vers soi, d’autres
personnes ou toute pièce mécanique en
engageant le fil de soudage.
LE SOUDAGE À L’ARC risque de
provoquer des interférences.
L’EXPLOSION DE LA BATTERIE
peut provoquer des blessures.
Ne pas utiliser l’appareil de soudage pour
charger des batteries ou faire démarrer
des véhicules à l’aide de câbles de démarrage,
sauf si l’appareil dispose d’une fonctionnalité
de charge de batterie destinée à cet usage.
Les PIÈCES MOBILES peuvent
causer des blessures.
S’abstenir de toucher des organes mobiles tels
que des ventilateurs.
Maintenir fermés et verrouillés les portes,
panneaux, recouvrements et dispositifs de
protection.
Lorsque cela est nécessaire pour des travaux d’entretien et de
dépannage, faire retirer les portes, panneaux, recouvrements
ou dispositifs de protection uniquement par du personnel qualifié.
Remettre les portes, panneaux, recouvrements ou dispositifs de
protection quand l’entretien est terminé et avant de rebrancher
l’alimentation électrique.
LIRE LES INSTRUCTIONS.
Lire et appliquer les instructions sur les
étiquettes et le Mode d’emploi avant l’installation, l’utilisation ou l’entretien de l’appareil.
Lire les informations de sécurité au début du
manuel et dans chaque section.
N’utiliser que les pièces de rechange recommandées par le
constructeur.
Effectuer l’entretien en respectant les manuels d’utilisation, les
normes industrielles et les codes nationaux, d’état et locaux.
OM-237 881 Page 8
Le rayonnement haute fréquence (H.F.) peut
provoquer des interférences avec les équipements de radio−navigation et de communication, les services de sécurité et les ordinateurs.
Demander seulement à des personnes qualifiées familiarisées
avec des équipements électroniques de faire fonctionner l’installation.
L’utilisateur est tenu de faire corriger rapidement par un électricien qualifié les interférences résultant de l’installation.
Si le FCC signale des interférences, arrêter immédiatement l’appareil.
Effectuer régulièrement le contrôle et l’entretien de l’installation.
Maintenir soigneusement fermés les portes et les panneaux des
sources de haute fréquence, maintenir les éclateurs à une distance correcte et utiliser une terre et un blindage pour réduire les
interférences éventuelles.
L’énergie électromagnétique risque de
provoquer des interférences pour l’équipement
électronique sensible tel que les ordinateurs et
l’équipement commandé par ordinateur tel que
les robots.
Veiller à ce que tout l’équipement de la zone de soudage soit
compatible électromagnétiquement.
Pour réduire la possibilité d’interférence, maintenir les câbles de
soudage aussi courts que possible, les grouper, et les poser
aussi bas que possible (ex. par terre).
Veiller à souder à une distance de 100 mètres de tout équipement électronique sensible.
Veiller à ce que ce poste de soudage soit posé et mis à la terre
conformément à ce mode d’emploi.
En cas d’interférences après avoir pris les mesures précédentes, il incombe à l’utilisateur de prendre des mesures supplémentaires telles que le déplacement du poste, l’utilisation de câbles blindés, l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone de travail.
2-4. Proposition californienne 65 Avertissements
Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des malformations congénitales et, dans certains cas, des cancers.
(Code de santé et de sécurité de Californie, chapitre 25249.5
et suivants)
Ce produit contient des produits chimiques, notamment du
plomb, dont l’État de Californie reconnaît qu’ils provoquent
des cancers, des malformations congénitales ou d’autres
problèmes de procréation. Se laver les mains après
utilisation.
2-5. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Combustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:
800-463-6727, website: www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website:
www.cdc.gov/NIOSH).
2-6. Informations relatives aux CEM
Le courant électrique qui traverse tout conducteur génère des champs
électromagnétiques (CEM) à certains endroits. Le courant issu d’un
soudage à l’arc (et de procédés connexes, y compris le soudage par
points, le gougeage, le découpage plasma et les opérations de
chauffage par induction) crée un champ électromagnétique (CEM)
autour du circuit de soudage. Les CEM peuvent créer des interférences
avec certains implants médicaux comme des stimulateurs cardiaques.
Des mesures de protection pour les porteurs d’implants médicaux
doivent être prises: Limiter par exemple tout accès aux passants ou
procéder à une évaluation des risques individuels pour les soudeurs.
Tous les soudeurs doivent appliquer les procédures suivantes pour
minimiser l’exposition aux CEM provenant du circuit de soudage:
1. Rassembler les câbles en les torsadant ou en les attachant avec
du ruban adhésif ou avec une housse.
2. Ne pas se tenir au milieu des câbles de soudage. Disposer les
câbles d’un côté et à distance de l’opérateur.
3. Ne pas courber et ne pas entourer les câbles autour de votre
corps.
4. Maintenir la tête et le torse aussi loin que possible du matériel du
circuit de soudage.
5. Connecter la pince sur la pièce aussi près que possible de la
soudure.
6. Ne pas travailler à proximité d’une source de soudage, ni
s’asseoir ou se pencher dessus.
7. Ne pas souder tout en portant la source de soudage ou le
dévidoir.
En ce qui concerne les implants médicaux :
Les porteurs d’implants doivent d’abord consulter leur médecin avant
de s’approcher des opérations de soudage à l’arc, de soudage par
points, de gougeage, du coupage plasma ou de chauffage par induction. Si le médecin approuve, il est recommandé de suivre les
procédures précédentes.
OM-237 881 Page 9
OM-237 881 Page 10
A complete Parts List is available at www.MillerWelds.com
SECTION 3 − DEFINITIONS
3-1. Manufacturer Safety Symbols And Definitions
Some symbols are found only on CE products.
Warning! Watch Out! There are possible hazards as shown by the symbols.
Safe1 2012−05
When power is applied failed parts can explode or cause other parts to explode.
Safe26 2012−05
3-2. Miscellaneous Symbols And Definitions
Shielded Metal
Arc (SMAW) Electrode Holder
Remote
Gas Metal Arc
Welding (GMAW)
Gun
Percent
Scratch Start TIG
Increase
Gas Metal Arc
Welding (GMAW)
I2
I1
V
Input Current
Volts
Gas Output
Positive
Rated Welding
Current
Pulse
Off
Touch Start
(GTAW)
Press
Single Phase
Input
Read Instructions
Arc Control
On
Gas Tungsten Arc
Welding (GTAW)
Torch
Three Phase
Foot Control
U1
A
Input Voltage
Amperes
Output
Negative
OM-237 881 Page 11
A complete Parts List is available at www.MillerWelds.com
SECTION 4 − SPECIFICATIONS
4-1. Features And Benefits
Auto-Linet Power Management Technology is circuitry that automatically adapts the power source to the primary voltage being applied
(see Sections 5-8 and 5-9).
LVCt Line Voltage Compensation is circuitry that keeps the power source output constant regardless of input power fluctuation.
Wind Tunnel Technologyt circulates air over components that require cooling, not over electronic circuitry, which reduces contaminants and improves reliability in harsh welding environments.
Fan-On-Demandt cooling system operates only when needed, reducing noise, energy use and the amount of contaminants pulled through the
machine.
Thermal Overload Protection automatically shuts down the unit, only when necessary to prevent damage to internal components if the duty cycle
is exceeded or air flow and cooling are restricted (see Section 4-6).
Auto Remote Sense enables the unit to automatically sense the connection of a remote control. Operation of the remote control is dependent on the
Mode Switch Setting (see Section 6-2).
Lift-Arct TIG starts provide a contamination free weld without the use of high frequency in the Lift-Arc TIG Welding Mode (see Section 7-3).
Synergic Pulsed MIG Operation allows single knob control of the arc. As wirefeed speed is increased or decreased, the pulse parameters increase
or decrease matching the power output to the wire speed (see Section 6-3).
4-2. Arc Controls
DIG control allows the arc characteristics, soft versus stiff, to be changed for specific applications and electrodes in CC and Stick Welding Modes
(see Sections 9-2 and 9-3).
Programmable Hot Start allows the start amperage and time to be changed for CC and Stick Welding Modes (see Sections 9-2 and 9-3).
Inductance influences the arc stiffness, bead width and appearance, and puddle fluidity in MIG and V-Sense Feeder Welding Modes
(see Sections 8-2 and 8-8).
SharpArct optimizes the size and shape of the arc cone, bead width and appearance, and puddle fluidity in Pulsed MIG Welding Mode
(see Section 8-4).
4-3. Serial Number And Rating Label Location
The serial number and rating information for this product is located on the rear panel. Use rating label to determine input power requirements and/or
rated output. For future reference, write serial number in space provided on back cover of this manual.
4-4. Unit Specifications
Do not use information in unit specifications table to determine electrical service requirements. See Sections 5-7 thru 5-9 for information on connecting input power.
Input
Power
Rated Output
3-Phase
350 A at 34
VDC, 60%
Duty Cycle
1-Phase
300 A at 32
VDC, 60%
Duty Cycle*
Voltage
Range in CV Mode
Amperage
Range in
CC Mode
Max.
OpenCircuit
Voltage
10−38 V
5−425 A
75 VDC
*See Section 4-6 for Duty Cycle Rating.
OM-237 881 Page 12
RMS Amps Input at Rated Load Output,
60 Hz 3-Phase at NEMA Load Voltages
and Class I Rating
208 V
230 V
400 V
460 V
575 V
KVA
KW
40.4
36.1
20.6
17.8
14.1
14.2
13.6
60.8
54.6
29.7
25.4
19.9
11.7
11.2
A complete Parts List is available at www.MillerWelds.com
4-5. Dimensions And Weight
A
Hole Layout Dimensions
E
F
A
11-3/4 in. (298 mm)
B
1-11/16 in. (42 mm)
C
15-3/4 in. (400 mm)
G
24 in.
(610 mm)
17 in.
(432 mm)
D
C
D
19-3/32 in. (485 mm)
E
8-11/16 in. (221 mm)
F
1-17/32 in. (39 mm)
G
1/4-20 UNC -2B thread
12-1/2 in.
(318 mm)
B
804 801-A
Weight
80 lb (36.3 kg)
93.5 lb (42.4 kg)
w/optional 115 VAC
Notes
OM-237 881 Page 13
A complete Parts List is available at www.MillerWelds.com
4-6. Duty Cycle And Overheating
Duty Cycle is percentage of 10 minutes that unit can weld at rated load
without overheating.
If unit overheats, output stops, a Help
message is displayed and cooling fan
runs. Wait fifteen minutes for unit to
cool. Reduce amperage or voltage, or
duty cycle before welding.
Single Phase Operation: The
unit is supplied with a 8 AWG
power cord. The rated output
with 8 AWG is 300 amps, 32
volts at 40% duty cycle. To
achieve 60% duty cycle change
cord to 6 AWG.
NOTICE − Exceeding duty cycle can
damage unit and void warranty.
500
425
400
WELDING AMPERES
350
300
THREE PHASE
OPERATION
250
6 AWG POWER CORD
200
8 AWG POWER CORD
SINGLE PHASE
OPERATION
150
100
10
15
20
25 30
40
% DUTY CYCLE
50
60 70 80 90 100
60% Duty Cycle
6 Minutes Welding
4 Minutes Resting
Overheating
A or V
0
15
Minutes
OR
Reduce Duty Cycle
Ref. 216 568-A
4-7. Static Output Characteristics
The static (output) characteristics of the welding power source can be described as flat during the GMAW process and drooping during the SMAW
and GTAW processes. Static characteristics are also affected by control settings (including software), electrode, shielding gas, weldment material,
and other factors. Contact the factory for specific information on the static characteristics of the welding power source.
OM-237 881 Page 14
A complete Parts List is available at www.MillerWelds.com
SECTION 5 − INSTALLATION
5-1. Selecting A Location
Movement
!
2
Do not move or operate unit
where it could tip.
2
OR
3
1
Location And Airflow
4
18 in.
(460 mm)
!
Special installation may be
required where gasoline or
volatile liquids are present −
see NEC Article 511 or CEC
Section 20.
1
Lifting Forks
Extend forks beyond opposite side
of unit.
2
Lifting Handles
Use handles to lift unit.
3
Hand Cart
Use cart or similar device to move
unit.
4
18 in.
(460 mm)
Line Disconnect Device
Locate unit near correct input
power supply.
loc_med 2015-04
Notes
OM-237 881 Page 15
A complete Parts List is available at www.MillerWelds.com
5-2. Selecting Cable Sizes*
NOTICE − The Total Cable Length in Weld Circuit (see table below) is the combined length of both weld cables. For example, if the power source
is 100 ft (30 m) from the workpiece, the total cable length in the weld circuit is 200 ft (2 cables x 100 ft). Use the 200 ft (60 m) column to determine
cable size.
Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit
Not Exceeding***
100 ft (30 m) or Less
Welding
Amperes
10 − 60%
Duty
Cycle
AWG (mm2)
150 ft
(45 m)
200 ft
(60 m)
60 − 100%
Duty Cycle
250 ft
(70 m)
300 ft
(90 m)
350 ft
(105 m)
400 ft
(120 m)
1/0 (60)
1/0 (60)
10 − 100% Duty Cycle
AWG (mm2)
AWG (mm2)
100
4 (20)
4 (20)
4 (20)
3 (30)
2 (35)
1 (50)
150
3 (30)
3 (30)
200
3 (30)
2 (35)
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
3/0 (95)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
4/0 (120)
250
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0 (2x70)
2x2/0 (2x70)
300
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0 (2x70)
2x3/0 (2x95)
2x3/0 (2x95)
350
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0 (2x70)
2x3/0 (2x95)
2x3/0 (2x95)
2x4/0 (2x120)
400
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0 (2x70)
2x3/0 (2x95)
2x4/0 (2x120)
2x4/0 (2x120)
500
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0 (2x70)
2x3/0 (2x95)
2x4/0 (2x120)
3x3/0 (3x95)
3x3/0 (3x95)
600
3/0 (95)
4/0 (120)
2x2/0 (2x70)
2x3/0 (2x95)
2x4/0 (2x120)
3x3/0 (3x95)
3x4/0 (3x120)
3x4/0 (3x120)
* This
chart is a general guideline and may not suit all applications. If cable overheats, use next size larger cable.
**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.
( ) = mm2 for metric use
***For distances longer than those shown in this guide, call a factory applications rep. at 920-735-4505 (Miller) or 1-800-332-3281 (Hobart).
Ref. S-0007-L 2015−02
5-3. Weld Output Terminals
!
Turn off power before connecting
to weld output terminals.
!
Do not use worn, damaged, undersized, or repaired cables.
1
Positive (+) Weld Output Terminal
2
Negative (−) Weld Output Terminal
See Sections 7-1 thru 9-1 for standard connection diagrams.
1
2
Ref. 804 772-A / output term1 2015−02
OM-237 881 Page 16
A complete Parts List is available at www.MillerWelds.com
5-4. Remote 14 Receptacle Information
Socket*
Socket Information
A
24 volts AC. Protected by supplementary protector CB2.
B
Contact closure to A completes 24 volts AC
contactor control circuit.
C
Output to remote control; 0 to +10 volts DC, +10
volts DC in MIG mode.
D
Remote control circuit common.
E
0 to +10 volts DC input command signal from
remote control.
L
Wirefeed speed command, 0 to +10 volts DC output signal from wire feeder.
M
CC/CV Select; 0 to +10 volts DC.
N
Wirefeed speed common.
A/V
F
Current feedback; +1 volt DC per 100 amperes.
AMPERAGE
VOLTAGE
H
Voltage feedback; +1 volt DC per 10 output receptacle volts.
G
Circuit common for 24 volts AC circuits.
K
Chassis common.
24 VOLTS AC
A
B
K
J
I
H
C L N
D M
G
E F
REMOTE
OUTPUT
CONTROL
GND
*The remaining sockets are not used.
5-5. Optional 115 Volts AC Duplex Receptacle And Supplementary Protectors
1
2
3
115 V 10 Amp AC Receptacle
Supplementary Protector CB1
Supplementary Protector CB2
CB1 protects duplex receptacle
from overload.
1
CB2 protects 24 volts AC portion of
Remote 14 receptacle from
overload.
Press button to supplementary protector.
2
3
803 691-C
OM-237 881 Page 17
A complete Parts List is available at www.MillerWelds.com
5-6. Optional Gas Valve Operation And Shielding Gas Connection
Obtain gas cylinder and chain to
running gear, wall, or other stationary support so cylinder cannot fall
and break off valve.
4
1
Cylinder
2
Regulator/Flowmeter
Install so face is vertical.
3
GAS IN
Gas Hose Connection
Fitting has 5/8-18 right-hand
threads. Obtain and install gas
hose.
2
4
Gas In Fitting
5
Gas Out Fitting
The Gas In and Gas Out fittings
have 5/8-18 right-hand threads.
Obtain proper size, type, and length
hose and make connections as follows:
Connect hose from shielding gas
supply regulator/flowmeter to Gas
In fitting.
Connect hose coupler to torch.
Connect one end of gas hose to
hose coupler. Connect remaining
end of gas hose to Gas Out fitting.
Operation
3
1
The gas solenoid controls gas flow
during the TIG process as follows:
Remote TIG
Gas flow starts with remote contactor on.
Gas flow stops at end of post−flow
if current was detected, or with remote contactor off if no current was
detected.
Lift−Arc TIG
Gas flow starts when tungsten
touches work (touch sensed).
Gas flow stops at end of post−flow.
Scratch Start TIG
5
GAS OUT
Gas flow starts when current is detected.
Gas flow stops at end of post−flow.
Post−flow time is factory set to 5
seconds per 100 amps of weld current. The minimum post−flow time
is 5 seconds. The maximum post−
flow is 20 seconds (post flow settings are not adjustable by the end
user).
Ref. 803 705-A / Ref. 803 691-C
OM-237 881 Page 18
A complete Parts List is available at www.MillerWelds.com
5-7. Electrical Service Guide
Elec Serv 2014−01
NOTICE − INCORRECT INPUT POWER can damage this welding power source. Phase to ground voltage shall not exceed +10% of rated input
voltage.
NOTICE − Actual input voltage should not be 10% less than minimum and/or 10% more than maximum input voltages listed in table. If actual input
voltage is outside this range, output may not be be available.
Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommendations are for a dedicated circuit sized for the rated output and duty cycle of the welding power source.
In dedicated circuit installations, the National Electrical Code (NEC) allows the receptacle or conductor rating to be less than the rating
of the circuit protection device. All components of the circuit must be physically compatible. See NEC articles 210.21, 630.11, and
630.12.
Single-Phase
Input Voltage (V)
208
230
400
460
575
Input Amperes (A) At Rated Output
60.8
54.6
29.7
25.4
19.9
Time-Delay Fuses 2
70
60
35
30
25
Normal Operating Fuses 3
80
80
45
40
30
Min Input Conductor Size In AWG/Kcmil 4
8
8
10
12
12
72
(22)
89
(27)
176
(54)
140
(43)
219
(67)
8
8
10
12
12
Input Voltage (V)
208
230
400
460
575
Input Amperes (A) At Rated Output
40.4
36.1
20.6
17.8
14.1
Time-Delay Fuses 2
45
40
25
20
15
Normal Operating Fuses 3
60
50
30
25
20
Max Recommended Standard Fuse Rating In Amperes 1
Max Recommended Input Conductor Length In Feet (Meters)
Min Grounding Conductor Size In AWG/Kcmil 4
Three-Phase
Max Recommended Standard Fuse Rating In Amperes 1
Min Input Conductor Size In AWG/Kcmil 4
Max Recommended Input Conductor Length In Feet (Meters)
Min Grounding Conductor Size In AWG/Kcmil 4
8
10
12
14
14
119
(36)
96
(29)
175
(53)
150
(46)
234
(71)
10
10
12
14
14
Reference: 2014 National Electrical Code (NEC) (including article 630)
1 If a circuit breaker is used in place of a fuse, choose a circuit breaker with time-current curves comparable to the recommended fuse.
2 “Time-Delay” fuses are UL class “RK5”. See UL 248.
3 “Normal Operating” (general purpose - no intentional delay) fuses are UL class “K5” (up to and including 60 amps), and UL class “H” ( 65 amps and
above).
4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table
310.15(B)(16). If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable
requirements.
OM-237 881 Page 19
A complete Parts List is available at www.MillerWelds.com
5-8. Connecting 1-Phase Input Power
1
8
=GND/PE Earth Ground
10
7
9
L1
L2
1
3
1
6
2
3
6
5
4
Tools Needed:
input1 2012−05 − Ref. 803 766-C
OM-237 881 Page 20
A complete Parts List is available at www.MillerWelds.com
5-8. Connecting 1-Phase Input Power (Continued)
!
Installation must meet all National and
Local Codes − have only qualified persons make this installation.
!
Disconnect and lockout/tagout input
power before connecting input conductors from unit. Follow established
procedures regarding the installation
and removal of lockout/tagout devices.
nected to any input power between 208 and
575 VAC without removing cover to relink the
power source.
See rating label on unit and check input voltage available at site.
1
Black And White Input Conductor (L1
And L2)
2
Red Input Conductor
Always connect green or green/yellow
conductor to supply grounding terminal first, and never to a line terminal.
3
Green Or Green/Yellow Grounding
Conductor
4
Insulation Sleeving
NOTICE − The Auto-Line circuitry in this unit
automatically adapts the power source to the
primary voltage being applied. Check input
voltage available at site. This unit can be con-
5
Electrical Tape
!
Insulate and isolate red conductor as shown.
6
Input Power Cord.
7
Disconnect Device (switch shown in the
OFF position)
8 Disconnect Device Grounding Terminal
9 Disconnect Device Line Terminals
Connect green or green/yellow grounding
conductor to disconnect device grounding terminal first.
Connect input conductors L1 and L2 to disconnect device line terminals.
10 Over-Current Protection
Select type and size of over-current protection
using Section 5-7 (fused disconnect switch
shown).
Close and secure door on disconnect device.
Follow established lockout/tagout procedures
to put unit in service.
input1 2012−05
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-237 881 Page 21
A complete Parts List is available at www.MillerWelds.com
5-9. Connecting 3-Phase Input Power
3
= GND/PE Earth Ground
4
7
2
L1
3
L2
5
L3
6
1
Tools Needed:
input2 2012−05 − Ref. 803 766-C
OM-237 881 Page 22
A complete Parts List is available at www.MillerWelds.com
5-9. Connecting 3-Phase Input Power (Continued)
!
!
!
Installation must meet all National and
Local Codes − have only qualified persons make this installation.
Disconnect and lockout/tagout input
power before connecting input conductors from unit. Follow established
procedures regarding the installation
and removal of lockout/tagout
devices.
Always connect green or green/yellow
conductor to supply grounding terminal first, and never to a line terminal.
NOTICE − The Auto-Line circuitry in this unit
automatically adapts the power source to the
primary voltage being applied. Check input
voltage available at site. This unit can be connected to any input power between 208 and
575 VAC without removing cover to relink the
power source.
See rating label on unit and check input voltage available at site.
5
Input Conductors (L1, L2 And L3)
6
Disconnect Device Line Terminals
Connect green or green/yellow grounding
conductor to disconnect device grounding terminal first.
For Three-Phase Operation
Connect input conductors L1, L2, and L3 to
disconnect device line terminals.
1
Input Power Cord.
7
2
Disconnect Device (switch shown in the
OFF position)
Select type and size of over-current protection using Section 5-7 (fused disconnect
switch shown).
3
Green Or Green/Yellow Grounding
Conductor
4
Disconnect Device Grounding Terminal
Over-Current Protection
Close and secure door on disconnect device.
Follow established lockout/tagout procedures
to put unit in service.
input2 2012−05
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-237 881 Page 23
A complete Parts List is available at www.MillerWelds.com
SECTION 6 − GENERAL OPERATION
6-1. Front Panel
6
4
9
2
3
5
7
8
10
11
12
13
14
1
15
19
18
16
17
804 772-A / 226 611-A
Weld
process operation sections describe functionality of the identified items.
1
2
3
4
5
6
Remote 14 Receptacle
Output ON Indicator Light
Volts Indicator
Left Display
Arc Length Indicator
Right Display
OM-237 881 Page 24
The meters display the actual weld output
values after arc initiation and remains displayed for approximately three seconds
after the arc is broken.
7 Amps Indicator
8 Setup Indicator
9 Adjust Control
10 Wire Type Indicator
11 Arc Control Indicator
12 Remote PC Interface
13
14
15
16
17
18
19
Setup Button
Gas Type Indicator
Mode Switch
Power Switch
Weld Output Terminal (−)
Optional Gas Valve Knockout
Weld Output Terminal (+)
A complete Parts List is available at www.MillerWelds.com
6-2. Mode Switch Settings
Switch Position
Process
Output Control
Panel Adjust
Remote Adjust
Scratch Start TIG
GTAW
Electrode Hot
Amps
% Panel Amps*
Lift-Arc TIG
GTAW
Electrode Hot
Amps
% Panel Amps*
TIG
GTAW
Remote 14
Amps
% Panel Amps
MIG
GMAW
Remote 14
Volts
Volts
Pulsed MIG
GMAW-P
Remote 14
Arc Length (0−100)*
Arc Length (0−100)*
Remote 14
Amps
% Panel Amps
Electrode Hot
Amps
% Panel Amps*
Electrode Hot
Volts
Volts
CC
Stick
V-Sense Feeder
SMAW
CAC-A
SMAW
CAC-A
GMAW*
*See Configuration Option Menu (see Section 6-3) For adjustment alternatives.
Notes
OM-237 881 Page 25
A complete Parts List is available at www.MillerWelds.com
6-3. Configuration Option Menu
4
3
5
SET
-UP
6
7
2
1
226 611-A
1
Mode Switch
2
3
Remote 14 Receptacle
Left Display
4
Right Display
5
6
Adjustment Control
Remote PC Interface
7
Setup Button
6-3
Setup
The Configuration Option Menu provides a
means to customize some machine features
for desired operation.
To enter the Configuration Option Menu, hold
the Setup Button down during power up while
the unit is displaying 8888 on the Left and
Right Displays. SET−UP will be displayed
momentarily.
Configuration options are displayed in the Left
Display. Settings are displayed in the Right
Display. Settings can be changed by turning
the Adjust Control. If a setting does not
change when the Adjust Control is turned, the
option is not configurable. Pressing the Setup
Button moves to the next configuration option.
Configuration Option Menu (Continued)
V.SEN
MIG
V-Sense Feeder Weld Process
This option enables MIG (V.SEN MIG) or Pulsed MIG
(V.SEN PULS) when the Mode Switch is in the VSENSE
FEEDER position. See Section 8-2 for MIG operation or Section 8-4 for Pulsed MIG operation.
Pulsed MIG Manual/Auto Control
PULS
AUTO
This option sets the PULSED MIG control as manual (PULS
MAN) or Auto (PULS AUTO) operation. When set to manual
operation, the arc length setting on power source and wire
speed setting on wirefeeder need to be adjusted independently to achieve the desired arc length. When set to Auto operation, once arc length is determined it is not necessary to
change the arc length value with changes in wirefeed speed.
The EXTREME 360 MAP and synergic feeders allow single
knob control of the arc. As wirefeed speed is increased or decreased, the pulse parameters increase or decrease matching the power output to the wire speed.
Auto Operation will only work with synergic wirefeeders.
All other wirefeeders will only operate as manual control.
Even when Auto is displayed, operation will be manual
when any other feeder is connected. See product literature for a list of compatible synergic feeders.
OM-237 881 Page 26
A complete Parts List is available at www.MillerWelds.com
6-3
Configuration Option Menu (Continued)
PULS
WFS
ARC.L
IPM
Pulsed MIG Adjustment
This option allows adjusting the Pulsed MIG process in units
of Arc Length (PULS ARC.L) or preset voltage (PULS
VOLT).
Wire Feed Speed And Wire Diameter Units
WFS IPM:
WFS is displayed in inches per minute
Diameter is displayed in inches
WFS MPM:
WFS is displayed in meters per minute
Diameter is displayed in millimeters
VRD
OFF
Voltage Reducing Device (VRD) Mode
This option enables (ON) or disables (OFF) low open circuit
voltage (OCV) operation in Stick and Scratch Start TIG
modes. See Section 9-4 for Low OCV Operation. When enabled, VRD ON is momentarily displayed after the power-on
front panel LED test.
If VRD -ON is displayed with a dash preceding ON, Low
OCV Operation is enabled by hardware configuration
and cannot be disabled in this menu.
PANL
RMT
Panel and Remote Adjustment
When the Mode Switch is set to SCRATCH START TIG,
LIFT−ARC TIG, or STICK, the remote command behavior is
configurable. SCRATCH START TIG and LIFT−ARC TIG
default to panel and remote (PANL RMT) amperage adjustment but can be configured for panel only (PANL ONLY) adjustment. The default amperage adjustment for STICK is
panel only (PANL ONLY) but can also be configured for panel
and remote (PANL RMT) adjustment. All other Mode Switch
positions are non−configurable and allow both panel and remote (PANL −RMT) adjustment.
Panel adjustment is made using the Adjust Control on
the front panel. Remote adjustment is made using a remote control device connected to the Remote 14 Receptacle.
INFO
NO
Revision Information
This option identifies the unit’s weld library (INFO LIB) and
firmware revision (INFO REV).
Press the Setup Button while the unit is displaying INFO LIB
to identify the unit’s weld library.
Press the Setup Button while the unit is displaying INFO REV
to identify the unit’s firmware revision.
Pressing the Setup Button while the unit is displaying INFO
NO will move to the next configuration option.
EXIT
NO
Exit Configuration Option Menu
Press the Setup Button while the unit is displaying EXIT NO
to return to the first configuration option. Press the Setup Button while the unit is displaying EXIT YES to exit the Configuration Option Menu.
The Configuration Option Menu can be exited at any time
by turning the unit off. Only if the unit is turned off after
EXIT NO is displayed will configuration option changes
be saved.
OM-237 881 Page 27
A complete Parts List is available at www.MillerWelds.com
SECTION 7 − GTAW OPERATION
7-1. Typical Connection For GTAW Process
!
Turn off power before making connections.
1
2
Foot Control
Gas Out Connection
(Optional)
Positive (+) Weld Output
Terminal
Remote 14 Receptacle
3
4
Connect desired remote control to
Remote 14 receptacle if required.
5
6
7
8
9
Gas In Connection (Optional)
Gas Cylinder
Negative (−) Weld Output
Terminal
TIG Torch
Workpiece
6
5
4
3
1
2
7
9
8
804 841-B
OM-237 881 Page 28
A complete Parts List is available at www.MillerWelds.com
7-2. Scratch Start TIG Welding Mode - GTAW Process
2
3
7 2. 0
4
5
6
8 5
1
226 611-A
!
Weld terminals are energized at all
times in Scratch Start TIG welding
mode.
1
Mode Switch
2
Volts Indicator
3
Left Display
4
Right Display
5
Amps Indicator
6
Adjust Control
Setup
For typical system connections refer to
Section 7-1.
Rotate Mode Switch to SCRATCH START
TIG position as shown.
The open circuit voltage is shown in the Left
Display with the Volts Indicator lit. Preset
amperage is shown in the Right Display
with the Amps Indicator lit.
Operation
The Adjust Control is used to set desired
preset amperage.
If a remote control is used for amper-
age adjustment, the adjustment will
function as a percentage of the preset
amperage.
For
best results, gently scratch the
tungsten electrode to the work to initiate an arc. To minimize arc flare at the
end of the weld, pull back the electrode
quickly to extinguish the arc.
OM-237 881 Page 29
A complete Parts List is available at www.MillerWelds.com
7-3. Lift-Arc TIG Welding Mode - GTAW Process
2
3
4
1 3. 5
6
5
85
1
226 611-A
8
“Touch”
1−2
Seconds
7
Do NOT Strike Like A Match!
!
Weld terminals are energized at all
times in Lift Arc TIG welding mode.
1
Mode Switch
2
Volts Indicator
3
Left Display
4
Right Display
5
Amps Indicator
6
Adjust Control
7
Workpiece
8
Tungsten Electrode
OM-237 881 Page 30
Setup
Operation
For typical system connections refer to
Section 7-1.
The Adjust Control is used to set desired
preset amperage.
Rotate Mode Switch to LIFT-ARC TIG position as shown.
If a remote control is used for amper-
The open-circuit voltage is shown in the
Left Display with the Volts Indicator lit. Preset amperage is shown in the Right Display
with the Amps Indicator lit.
Normal open-circuit voltage is not present
before the electrode touches the workpiece, instead a low sensing voltage is
present. The sensing voltage allows the
electrode to touch the workpiece without
overheating, sticking, or getting contaminated.
age adjustment, the adjustment will
function as a percentage of the preset
amperage.
For best results, firmly touch the tung-
sten electrode to the workpiece at the
weld start point. Hold electrode to
workpiece for 1-2 seconds, and lift
electrode. An arc will form when the
electrode is lifted. To minimize arc flare
at the end of the weld, pull back the
electrode quickly to extinguish the arc.
A complete Parts List is available at www.MillerWelds.com
7-4. TIG Welding Mode - GTAW Process
2
3
4
5
85
1
226 611-A
!
Weld terminals are energized
through the remote control in TIG
welding mode.
1
2
3
4
5
Mode Switch
Left Display
Right Display
Amps Indicator
Adjust Control
Setup
For typical system connections refer to
Section 7-1.
Rotate Mode Switch to TIG position as
shown.
The preset amperage is shown in the Right
Display with the Amps Indicator lit.
Operation
The Adjust Control is used to set desired
preset amperage.
A remote control is required to turn on the
weld output.
If the remote control has an amperage
adjustment, the adjustment will function as a percentage of the preset amperage.
For
best results, gently scratch the
tungsten electrode to the work to initiate an arc. To minimize arc flare at the
end of the weld, pull back the electrode
quickly to extinguish the arc.
OM-237 881 Page 31
A complete Parts List is available at www.MillerWelds.com
SECTION 8 − GMAW/GMAW-P/FCAW OPERATION
8-1. Typical Connection For Remote Control Feeder GMAW/GMAW-P/FCAW Process
9
1
2
3
4
8
7
5
6
804 938-A
5
Workpiece
6
Gun
7
Wire Feeder
Negative (−) Weld Output Terminal
8
Gas Hose
Ground Cable to Workpiece
9
Gas Cylinder
!
Turn off power before making
connections.
1
Remote 14-Receptacle
2
Positive (+) Weld Output Terminal
3
4
OM-237 881 Page 32
Use of shielding gas is dependant on Wire
Type.
The
connection diagram illustrates
DCEP (reverse polarity) suitable for all
wires except self-shielded FCAW. The
majority of self-shielded FCAW wires
require DCEN (straight polarity).
A complete Parts List is available at www.MillerWelds.com
Notes
OM-237 881 Page 33
A complete Parts List is available at www.MillerWelds.com
8-2. MIG Welding Mode - GMAW/FCAW Process
2
3
4
5
2 5.0
6
7
8
9
1
226 611-A
!
Weld terminals are energized
through the remote control in MIG
welding mode.
1
Mode Switch
2
Volts Indicator
3
Left Display
4
Right Display
5
Adjust Control
6
Wire Type Indicator
7
Arc Control Indicator
8
Setup Button
9
Gas Type Indicator
The preset voltage can be adjusted re-
motely at the wire feeder if the feeder
has a voltage control. This voltage control will override the Adjust Control of
preset voltage on the welding power
source.
Pressing the Setup Button allows adjustment of Arc Control, Wire Type, Gas Type
and preset voltage.
For best results, select the appropriate
Wire and Gas Type to match the actual
wire and gas being used. Refer to the
MIG − Wire and Gas Selection Table
for available wires and gases (see
Section 8-3).
Press the Setup Button to confirm the
selection. The unit will acknowledge a
change of wire and gas information by displaying PROG LOAD momentarily.
Arc Control (Inductance)
Press the Setup Button repeatedly until the
Arc Control indicator is lit. INDU appears on
the Left Display, and the corresponding inductance setting appears on the Right Display.
Selecting a Wire and Gas
Rotate Adjust Control to select desired inductance setting from 0 to 100. Use lower
inductance settings to stiffen the arc and reduce puddle fluidity. Use higher inductance
settings to soften the arc and increase
puddle fluidity.
Rotate Mode Switch to MIG position as
shown.
Press the Setup Button repeatedly until the
Wire Type indicator is lit. The active Wire
Type will appear in the Left and Right Display.
Refer to the MIG − Wire and Gas Selection
Table (see Section 8-3) for suggested inductance setting for the specific wire and
gas being used.
The preset voltage is shown in the Left Display with the Volts Indicator lit.
Rotate Adjust Control to select desired
wire.
Press the Setup Button to return to adjustment of preset voltage.
Operation
Press the Setup Button again so the Gas
Type indicator is lit. The active Gas Type
will appear in the Left and Right Display.
Each Wire and Gas Type combination
Setup
For typical system connections refer to
Section 8-1.
While the Volts Indicator is lit under the Left
Display, the Adjust Control is used to set
desired preset voltage.
OM-237 881 Page 34
Rotate Adjust Control to select desired gas.
has independent preset voltage and inductance settings. These settings are
preserved when the unit is turned off.
A complete Parts List is available at www.MillerWelds.com
8-3. MIG - Wire and Gas Selection Table
WIRE TYPES**
GAS TYPES
DEFAULT INDUCTANCE
.035 (0.9) STL
.045 (1.2) STL
.052 (1.4) STL
ARGN CO2 (ARGON / CARBON DIOXIDE)
ARGN OXY (ARGON / OXYGEN)
30
.035 (0.9) STL
.045 (1.2) STL
CO2 (CARBON DIOXIDE)
10
Flux Core
.035 (0.9) FCAW
.045 (1.2) FCAW
.052 (1.4) FCAW
1/16 (1.6) FCAW
ARGN CO2 (ARGON / CARBON DIOXIDE) *
CO2 (CARBON DIOXIDE)
30 *
Metal Core
.045 (1.2) MCOR
.052 (1.4) MCOR
1/16 (1.6) MCOR
ARGN CO2 (ARGON / CARBON DIOXIDE)
30
Stainless Steel
.035 (0.9) SSTL
.045 (1.2) SSTL
Steel
TRI MIX (TRI-GAS MIXTURE)
ARGN OXY (ARGON / OXYGEN)
70
.035 (0.9) AL4X (4000 Series)
.040 (1.0) AL4X (4000 Series)
3/64 (1.2) AL4X (4000 Series)
1/16 (1.6) AL4X (4000 Series)
Aluminum
ARGN (ARGON)
10
.035 (0.9) AL5X (5000 Series)
.040 (1.0) AL5X (5000 Series)
3/64 (1.2) AL5X (5000 Series)
1/16 (1.6) AL5X (5000 Series)
*For self-shielded FCAW wires use the ARGN CO2 gas selection and set inductance to less than 10.
**Wire diameter in inches (mm). Refer to section 6-3 to change displayed units.
Notes
OM-237 881 Page 35
A complete Parts List is available at www.MillerWelds.com
8-4. Pulsed MIG Welding Mode - GMAW-P Process
2
3
4
5
6
25.0
7
8
9
10
1
!
Weld terminals are energized
through the remote control in
Pulsed MIG welding mode.
1
2
3
4
5
6
7
8
9
10
Mode Switch
Volts Indicator
Left Display
Right Display
Arc Length Indicator
Adjust Control
Wire Type Indicator
Arc Control Indicator
Setup Button
Gas Type Indicator
Setup
For typical system connections refer to
Section 8-1.
Rotate Mode Switch to PULSED MIG position as shown.
The trim setting is shown in the Left Display
with the Arc Length Indicator lit.
Operation
While the Arc Length Indicator is lit under
the Left Display, the Adjust Control is used
to set desired trim setting.
The trim can be adjusted remotely at
the wire feeder if the feeder has a voltage control. This voltage control will
override the Adjust Control of trim on
the welding power source.
Pressing the Setup Button allows adjustment of Arc Control, Wire Type, Gas Type
and Arc Length.
For best results, select the appropriate
Wire and Gas Type to match the actual
wire and gas being used. Refer to
OM-237 881 Page 36
Pulsed MIG − Wire and Gas Selection
Table for available wires and gases
(see Section 8-5).
Selecting a Wire and Gas
Press the Setup Button repeatedly until the
Wire Type indicator is lit. The active Wire
Type will appear in the Left and Right Display.
Rotate Adjust Control to select desired
wire.
Press the Setup Button again so the Gas
Type indicator is lit. The active Gas Type
will appear in the Left and Right Display.
Rotate Adjust Control to select desired gas.
Press the Setup Button again to confirm the
selection. The unit will acknowledge a
change of wire and gas information by displaying PROG LOAD momentarily.
Arc Control (SharpArc)
Press the Setup Button repeatedly until the
Arc Control indicator is lit. SHRP appears
on the Left Display, and the corresponding
SharpArc setting appears on the Right Display.
Rotate Adjust Control to select desired
SharpArc setting from 0 to 50, default is 25.
Adjusting the SharpArc setting changes the
welding arc cone. Lower settings widen the
arc cone, increases puddle fluidity and flattens the weld bead appearance.
Higher settings narrow the arc cone, reduces puddle fluidity and crowns the weld
bead appearance.
Each Wire and Gas Type combination
has independent Arc Length and SharpArc settings. These settings are preserved when the unit is turned off.
226 611-A
Arc Length - Pulsed MIG Manual Control
(see Section 6-3)
Arc length corresponds to the level of energy needed to burn off the welding electrode.
As wire feed speed increases, a higher arc
length setting is required to burn off the
additional wire. The arc length setting appears in the Left Display when the Arc
Length Indicator is lit. Arc length can be adjusted from 0 to 100.
After the welding output terminals are energized, but prior to arc initiation, the unit displays the letter “R” and a reference wire
speed (IPM) on the Right Display. The reference wire speed can be used as a starting point for the wire speed setting at the
feeder. The wire speed and arc length setting can then be further adjusted to achieve
the desired arc length.
The Configuration Option Menu (see Section 6-1) can be used to change the arc
length setting (0 to 100) to average arc voltage. Average arc voltage can be used as an
alternative method to set the Pulsed MIG
welding arc with the same parameters
(voltage and wire speed) as a conventional
MIG arc. Lower voltage settings correspond to tighter arc lengths while higher
voltage settings correspond to longer arc
lengths. If the voltage mode is selected, the
average voltage preset will be displayed on
the Left Display with the Volts Indicator lit.
Arc Length - Pulsed MIG Auto Control
(see Section 6-3)
In Auto operation the arc length setting is
0-100. The programs have been developed
at 50 arc length setting. Increasing or decreasing the arc length setting from 50 will
change the arc length. It is not necessary to
change the arc length value when changing
wire feed speed settings.
A complete Parts List is available at www.MillerWelds.com
8-5. Pulsed MIG - Wire and Gas Selection Table
WIRE TYPES*
GAS TYPES
Steel
.035 (0.9) STL
.045 (1.2) STL
ARGN CO2 (ARGON / CARBON DIOXIDE)
80 ARGN CO2 (ARGON / CARBON DIOXIDE)
ARGN OXY (ARGON / OXYGEN)
Steel 100S
.035 (0.9) STL
.045 (1.2) STL
100S C5 (95 ARGON / 5 CARBON DIOXIDE)
Metal Core
.045 (1.2) MCOR
.052 (1.4) MCOR
ARGN CO2 (ARGON / CARBON DIOXIDE)
Stainless Steel
.035 (0.9) SSTL
.045 (1.2) SSTL
TRI MIX (TRI-GAS MIXTURE)
ARGN OXY (ARGON / OXYGEN)
ARGN CO2 (ARGON / CARBON DIOXIDE)
.035 (0.9) AL4X (4000 Series)
.040 (1.0) AL4X (4000 Series)
3/64 (1.2) AL4X (4000 Series)
1/16 (1.6) AL4X (4000 Series)
Aluminum
.035 (0.9) AL49 (4943)
.040 (1.0) AL49 (4943)
3/64 (1.2) AL49 (4943)
1/16 (1.6) AL49 (4943)
ARGN (ARGON)
.035 (0.9) AL5X (5000 Series)
.040 (1.0) AL5X (5000 Series)
3/64 (1.2) AL5X (5000 Series)
1/16 (1.6) AL5X (5000 Series)
ARGN (ARGON)
HE AR25 (HELIUM/ARGON)
Nickel
.035 (0.9) NI
.045 (1.2) NI
ARGN HE (ARGON / HELIUM)
ARGN (ARGON)
Copper Nickel
.035 (0.9) CUNI
.045 (1.2) CUNI
HE ARGN (HELIUM / ARGON)
Silicon Bronze
.035 (0.9) SIBR
.045 (1.2) SIBR
ARGN (ARGON)
.035 (0.9) TI-5
.045 (1.2) TI-5
ARGN HE25 (75 ARGON / 25 HELIUM)
.035 (0.9) TI-5
.045 (1.2) TI-5
ARGN HE50 (50 ARGON / 50 HELIUM)
Titanium
*Wire diameter in inches (mm). Refer to section 6-3 to change displayed units.
Other normal gas mixtures can be used by adjusting arc length and sharp arc. Use the program closest to your gas mixture and wire type and
size.
Notes
OM-237 881 Page 37
A complete Parts List is available at www.MillerWelds.com
8-6. Remote Process Select
This power source can be used with wire
feeders that support Remote Process Select. This feature allows the operator to
switch the active welding process between
MIG and Pulsed MIG at the wire feeder. To
determine if the welding system is Remote
Process Select capable, connect the wire
feeder to the power source and review the
power source display variations shown below.
When used with an XMT power source,
the Process Select knob must be set to
Pulsed MIG for Remote Process Select
to be active.
Power Source Display − Wire Feeder with
Remote Process Select Not Detected
50
25.0
50
When the power source Right Display is
blank, a wire feeder with Remote Process
Select is not detected. Set the active weld
process at the power source.
MIG
PULS
Power Source Display − Wire Feeder with
Remote Process Select Detected
When the power source Right Display is
MIG, a wire feeder with Remote Process Select is detected and set for MIG operation.
The active weld process can only be
changed at the wire feeder.
Power Source Display − Wire Feeder with
Remote Process Select Detected and Set
for Pulsed MIG
When the power source Right Display is
PULS, a Remote Process Select wire feeder
is detected and is set for Pulsed MIG operation. The active weld process can only be
changed at the wire feeder.
Using a Dual Wire Feeder with Remote
Process Select
When using a dual wire feeder with Remote
Process Select, different weld programs for
the left and right side can be selected. The
power source MIG and Pulsed MIG programs for the left side of wire feeder are selected with the left side of the wire feeder active. The power source MIG and Pulsed MIG
programs for the right side are selected with
the right side of the wire feeder active. When
the right side of the wire feeder is active, the
power source Right Display will show a
decimal point in the lower right hand corner
as shown.
25.0
MIG.
Power Source Display − Dual Wire Feeder with Right Side Active and Set for MIG
Decimal point indicates wire
feeder right side is active.
50
PULS.
Decimal point indicates wire
feeder right side is active.
OM-237 881 Page 38
Power Source Display − Dual Wire Feeder with Right Side Active and Set for
Pulsed MIG
A complete Parts List is available at www.MillerWelds.com
8-7. Typical Connection For Voltage-Sensing Feeder GMAW/GMAW-P/FCAW Process
!
Turn off power before making connections.
1
Positive (+) Weld Output
Terminal
2 Negative (−) Weld Output
Terminal
3 Ground Cable to Workpiece
4 Workpiece
5 Voltage Sensing Clamp
6 Gun
7 Gun Trigger Receptacle
8 Wire Feeder
9 Gas Hose
10 Gas Cylinder
Use of shielding gas is dependant
on Wire Type.
The connection diagram illus-
trates DCEP (reverse polarity)
suitable for all wires except
self-shielded FCAW. The majority of self-shielded FCAW
wires require DCEN (straight
polarity).
10
1
9
3
2
8
4
7
5
6
804 843-B
OM-237 881 Page 39
A complete Parts List is available at www.MillerWelds.com
8-8. V-Sense Feeder Welding Mode - GMAW/FCAW Process
2
3
4
5
2 5.0
6
7
8
9
1
226 611-A
!
Weld terminals are energized at all
times in V-Sense Feeder welding
mode.
Operation
1
Mode Switch
While the Volts Indicator is lit under the Left
Display, the Adjust Control is used to set
desired preset voltage.
2
Volts Indicator
The Left Display toggling momentarily
3
Left Display
4
Right Display
5
Adjust Control
6
Wire Type Indicator
7
Arc Control Indicator
8
Setup Button
9
Gas Type Indicator
Setup
For typical system setup connections refer
to Section 8-7.
Rotate Mode Switch to V-SENSE FEEDER
position as shown.
The Left Display toggles between open circuit voltage and preset voltage with the
Volts Indicator lit.
pauses while the preset voltage is adjusted.
Pressing the Setup Button allows adjustment of Arc Control, Wire Type, Gas Type
and preset voltage.
For best results, select the appropriate
Wire and Gas Type to match the actual
wire and gas being used.
Refer to MIG − Wire and Gas Selection
Table for available wires and gases (see
Section 8-3).
Selecting a Wire and Gas
Press the Setup Button repeatedly until the
Wire Type indicator is lit. The active Wire
Type will appear in the Left and Right Display.
Rotate Adjust Control to select desired
wire.
Press the Setup Button again so the Gas
Type indicator is lit. The active Gas Type
will appear in the Left and Right Display.
OM-237 881 Page 40
Rotate Adjust Control to select desired gas.
Press the Setup Button again to confirm the
selection. The unit will acknowledge a
change of wire and gas information by displaying PROG LOAD momentarily.
Arc Control (Inductance)
Press the Setup Button repeatedly until the
Arc Control indicator is lit. INDU appears on
the Left Display, and the corresponding inductance setting appears on the Right Display.
Rotate Adjust Control to select desired inductance setting from 0 to 100. Use lower
inductance settings to stiffen the arc and reduce puddle fluidity. Use higher inductance
settings to soften the arc and increase
puddle fluidity.
Refer to the MIG − Wire and Gas Selection
Table (see Section 8-3) for suggested inductance setting for the specific wire and
gas being used.
Each Wire and Gas Type combination
has independent preset voltage and inductance settings. These settings are
preserved when the unit is turned off.
A complete Parts List is available at www.MillerWelds.com
8-9. V-Sense Feeder Welding Mode - GMAW-P Process
2
3
2 5.0
4
5
6
R200
7
8
9
10
1
226 611-A
!
Weld terminals are energized at all
times in V-Sense Feeder welding
mode.
1
Mode Switch
2
Volts Indicator
3
4
Left Display
Right Display
5
Arc Length Indicator
6
7
Adjust Control
Wire Type Indicator
8
Arc Control Indicator
9
Setup Button
10 Gas Type Indicator
Setup
For typical system setup connections refer
to Section 8-7.
Rotate Mode Switch to V-SENSE FEEDER
position as shown.
The Left Display toggles between open circuit voltage and the trim setting. The open
circuit voltage is shown while the Volts Indicator is lit, and the trim setting is shown
while the Arc Length Indicator is lit.
Operation
While the Arc Length Indicator is lit under
the Left Display, the Adjust Control is used
to set desired trim setting.
The Left Display toggling momentarily
pauses while the trim setting is adjusted.
Pressing the Setup Button allows adjust-
ment of Arc Control, Wire Type, Gas Type
and Arc Length.
For best results, select the appropriate
Wire and Gas Type to match the actual
wire and gas being used.
Refer to Pulsed MIG − Wire and Gas Selection Table for available wires and gases
(see Section 8-5).
Higher settings narrow the arc cone, reduces puddle fluidity and crowns the weld
bead appearance.
Each Wire and Gas Type combination
has independent Arc Length and SharpArc settings. These settings are preserved when the unit is turned off.
Arc Length (Trim)
Selecting a Wire and Gas
Press the Setup Button repeatedly until the
Wire Type indicator is lit. The active Wire
Type will appear in the Left and Right Display.
Rotate Adjust Control to select desired
wire.
Press the Setup Button again so the Gas
Type indicator is lit. The active Gas Type
will appear in the Left and Right Display.
Rotate Adjust Control to select desired gas.
Press the Setup Button again to confirm the
selection. The unit will acknowledge a
change of wire and gas information by displaying PROG LOAD momentarily.
Arc Control (SharpArc)
Press the Setup Button repeatedly until the
Arc Control indicator is lit. SHRP appears
on the Left Display, and the corresponding
SharpArc setting appears on the Right Display.
Rotate Adjust Control to select desired
SharpArc setting from 0 to 50, default is 25.
Adjusting the SharpArc setting changes the
welding arc cone. Lower settings widen the
arc cone, increases puddle fluidity and flattens the weld bead appearance.
Trim corresponds to the level of energy
needed to burn off the welding electrode.
As wire feed speed increases, a higher trim
setting is required to burn off the additional
wire. The trim setting appears in the Left
Display when the Arc Length Indicator is lit.
Trim can be adjusted from 0 to 100.
Prior to arc initiation, the unit displays the
letter “R” and a reference wire speed (IPM)
on the Right Display. The reference wire
speed can be used as a starting point for
the wire speed setting at the feeder. The
wire speed and trim can then be further adjusted to achieve the desired arc length.
The Configuration Option Menu (see Section 6-3) can be used to change the Arc
Length setting from trim (0 to 100) to average arc voltage. Average arc voltage can
be used as an alternative method to set the
Pulsed MIG welding arc with the same parameters (voltage and wire speed) as a
conventional MIG arc. Lower voltage settings correspond to tighter arc lengths while
higher voltage settings correspond to longer arc lengths. If the voltage mode is selected, the average preset voltage will be
displayed on the Left Display with the Volts
Indicator lit.
OM-237 881 Page 41
A complete Parts List is available at www.MillerWelds.com
SECTION 9 − SMAW/CAC-A OPERATION
9-1. Typical Connection For SMAW And CAC-A Process
!
Turn off power before making connections.
1
Electrode Holder
(Carbon Arc)
For CAC-A process connect carbon arc cutting torch to to positive
weld output terminal.
2
3
4
Electrode Holder
Positive (+) Weld Output
Terminal
Remote 14 Receptacle
Connect desired remote control to
remote 14 receptacle as required.
5
6
7
Compressed Air LIne
Negative (−) Weld Output
Terminal
Workpiece
5
4
3
2
1
6
7
Ref. 804 842-B
OM-237 881 Page 42
A complete Parts List is available at www.MillerWelds.com
9-2. CC Welding Mode - SMAW/CAC-A Process
2
5
4
3
8 5
6
7
1
226 611-A
!
1
2
3
4
5
6
7
Weld terminals are energized
through the remote control in CC
welding mode.
Mode Switch
Left Display
Right Display
Amps Indicator
Adjust Control
Arc Control Indicator
Setup Button
Setup
For typical system connections refer to
Section 9-1.
Rotate Mode Switch to CC position as
shown.
The preset amperage is shown in the Right
Display with the Amps Indicator lit.
If the remote control has an amperage
adjustment, the adjustment will function as a percentage of the preset amperage.
Pressing the Setup Button allows adjustment of Arc Control, Hot Start Current and
Hot Start Time.
For best results at the end of the weld,
pull back the electrode quickly to extinguish the arc.
Arc Control (Dig)
Press the Setup Button so the Arc Control
indicator is lit. DIG appears on the Left Display, and the corresponding dig setting appears on the Right Display.
Rotate Adjust Control to select desired dig
setting from 0 to 100.
Operation
While the Amps Indicator is lit under the
Right Display, the Adjust Control is used to
set desired preset amperage.
A remote control is required to turn on the
weld output.
Dig control allows the arc characteristics,
soft versus stiff, to be changed for specific
applications and electrodes. Lower the dig
setting for smooth running electrodes like
E7018 and increase the dig setting for stiffer, more penetrating electrodes like E6010.
Press the Setup Button repeatedly until the
Arc Control light goes out to return to adjustment of preset amperage.
Programmable Hot Start
Press the Setup button repeatedly until
HOT.S appears on the Left Display. HOT.S
adjusts the Hot Start Amperage to Adaptive
Hot Start (AUTO) or from Min (1) to Max
(50). Adaptive Hot Start (AUTO) automatically chooses a default amperage. The Min
(1) setting results in no hot start amperage.
Higher numbers result in higher start amperage.
Press the Setup button again so HOT.T appears on the Left Display. HOT.T adjusts
the Hot Start Time to Adaptive Hot Start
(AUTO) or from Min (1) to Max (50). Adaptive Hot Start (AUTO) automatically
chooses a default Time. The Min (1) setting
results in no hot start time. Higher numbers
result in longer start time.
Press the Setup Button to return to adjustment of preset amperage.
Use
this mode for Air Carbon Arc
(CAC−A) cutting and gouging. For best
results, adjust dig setting to maximum.
OM-237 881 Page 43
A complete Parts List is available at www.MillerWelds.com
9-3. Stick Welding Mode - SMAW/CAC-A Process
2
4
3
7 2. 0
5
6
85
7
8
1
226 611-A
!
Weld terminals are energized at all
times in Stick welding mode.
Right Display, the Adjust Control is used to
set desired preset amperage.
1
2
3
4
5
6
7
8
Mode Switch
Volts Indicator
Left Display
Right Display
Amps Indicator
Adjust Control
Arc Control Indicator
Setup Button
Pressing the Setup Button allows adjustment of Arc Control, Hot Start Current and
Hot Start Time.
Setup
For typical system connections refer to
Section 9-1.
Rotate Mode Switch to STICK position as
shown.
The open circuit voltage is shown in the Left
Display with the Volts Indicator lit, and the
preset amperage is shown in the Right Display with the Amps Indicator lit.
Operation
While the Amps Indicator is lit under the
OM-237 881 Page 44
For best results at the end of the weld,
pull back the electrode quickly to extinguish the arc.
Arc Control (Dig)
Press the Setup Button so the Arc Control
indicator is lit. DIG appears on the Left Display, and the corresponding dig setting appears on the Right Display.
Rotate Adjust Control to select desired dig
setting from 0 to 100.
Dig control allows the arc characteristics,
soft versus stiff, to be changed for specific
applications and electrodes. Lower the dig
setting for smooth running electrodes like
E7018 and increase the dig setting for stiffer, more penetrating electrodes like E6010.
Press the Setup Button repeatedly until the
Arc Control light goes out to return to adjustment of preset amperage.
Programmable Hot Start
Press the Setup button repeatedly until
HOT.S appears on the Left Display. HOT.S
adjusts the Hot Start Amperage to Adaptive
Hot Start (AUTO) or from Min (1) to Max
(50). Adaptive Hot Start (AUTO) automatically chooses a default amperage. The Min
(1) setting results in no hot start amperage.
Higher numbers result in higher start amperage.
Press the Setup button again so HOT.T appears on the Left Display. HOT.T adjusts
the Hot Start Time to Adaptive Hot Start
(AUTO) or from Min (1) to Max (50). Adaptive Hot Start (AUTO) automatically
chooses a default Time. The Min (1) setting
results in no hot start time. Higher numbers
result in longer start time.
Use
this mode for Air Carbon Arc
(CAC−A) cutting and gouging. For best
results, adjust dig setting to maximum.
A complete Parts List is available at www.MillerWelds.com
9-4.
Optional Low Open Circuit Voltage (OCV) Welding Modes
Low OCV Operation
The unit can be optionally configured for low open circuit voltage (OCV) operation in Stick and Scratch Start TIG modes. When the unit is configured for low OCV operation only a low sensing voltage (approximately 15 VDC) is present between the electrode and the workpiece prior to the
electrode touching the workpiece. Consult a Factory Authorized Service Agent for information regarding how to configure the unit for low OCV
welding operation.
Notes
OM-237 881 Page 45
A complete Parts List is available at www.MillerWelds.com
SECTION 10 − MAINTENANCE & TROUBLESHOOTING
10-1. Routine Maintenance
!
= Check
= Change
= Clean
Maintain more
Disconnect power
before maintaining.
often during
severe conditions.
= Replace
Replace
Damaged
Or
Unreadable
Labels
Replace Cracked
Torch Body
Repair Or
Replace
Cracked
Cables
Every
3
Months
Repair Or Replace
Cracked Cables And
Cords
Clean
And
Tighten Weld
Connections
Every
6
Months
Blow Out Inside
10-2. Blowing Out Inside Of Unit
!
Do not remove case when
blowing out inside of unit.
To blow out unit, direct airflow
through front and back louvers as
shown.
Blowing Out Unit 2010−01
OM-237 881 Page 46
A complete Parts List is available at www.MillerWelds.com
10-3. Help Displays
All directions are in reference to the front
of the unit. All circuitry referred to is located inside the unit.
1
HELP
HELP
2
3
HELP
Help 2 Display
Indicates a malfunction in the thermal protection circuitry. If this display is shown, contact
a Factory Authorized Service Agent.
Help 3 Display
Indicates the left side of the unit has overheated. The unit has shut down to allow the
fan to cool it (see Section 4-6). Operation will
continue when the unit has cooled.
5
6
Help 6 Display
8
Help 8 Display
HELP
HELP
Indicates a malfunction in the primary power
circuit. If this display is shown, contact a Factory Authorized Service Agent.
Help 5 Display
HELP
HELP
Help 1 Display
25
Indicates the right side of the unit has overheated. The unit has shut down to allow the
fan to cool it (see Section 4-6). Operation will
continue when the unit has cooled.
Indicates operation at maximum input current. The unit has a maximum allowable input
current limit. As the line voltage decreases,
the required input current increases. If the line
voltage is too low, the output power is limited
by the input current. When this limit is
reached, the unit automatically reduces output power to continue operation. If this display
is shown, have a qualified electrician check
the input voltage.
Indicates a malfunction in the secondary
power circuit of the unit. If this display is
shown, contact a Factory Authorized Service
Agent.
Help 25 Display
Indicates machine has reached duty cycle
limits (see Section 4-6). Unit must be left on
to power the fan for cooling. Operation will
continue when unit has cooled.
OM-237 881 Page 47
A complete Parts List is available at www.MillerWelds.com
10-4. Troubleshooting
Trouble
No weld output; unit completely inoperative.
Remedy
Place line disconnect switch in On position (see Sections 5-8 and 5-9).
Check and replace line fuse(s), if necessary, or reset circuit breaker (see Sections 5-8 and 5-9).
Check for proper input power connections (see Sections 5-8 and 5-9).
No weld output; meter display On.
Input voltage outside acceptable range of variation (see Section 5-7).
Check, repair, or replace remote control.
Unit overheated. Allow unit to cool with fan On (see Section 4-6).
Erratic or improper weld output.
Use proper size and type of weld cable (see Section 5-2).
Clean and tighten all weld connections.
Check for correct polarity.
No 115 volts AC output at optional
duplex receptacle.
Reset supplementary protector CB1 (see Section 5-5).
No 24 volts AC output at Remote 14
receptacle.
Reset supplementary protector CB2 (see Section 5-5).
Notes
OM-237 881 Page 48
A complete Parts List is available at www.MillerWelds.com
Notes
OM-237 881 Page 49
SECTION 11 − ELECTRICAL DIAGRAM
Figure 11-1. Circuit Diagram
OM-237 881 Page 50
271 735-B
OM-237 881 Page 51
Notes
SOCKET/WRENCH SELECTION TABLE
(U.S. STANDARD)
Specifications
Socket or Wrench Size
SOCKET/WRENCH SELECTION TABLE
(METRIC)
Specifications
Socket or Wrench Size
Bolt
Diameter
Decimal
Equivalent
Bolt
Nut
Bolt
Diameter
U.S.
Decimal
Equivalent
Bolt
Nut
1/4 in
.250 in
3/8 in
7/16 in
6 mm
.2362 in
10 mm
10 mm
5/16 in
.3125 in
1/2 in
9/16 in
8 mm
.3150 in
14 mm
14 mm
3/8 in
.375 in
9/16 in
5/8 in
10 mm
.3937 in
17 mm
17 mm
7/16 in
.4375 in
5/8 in
3/4 in
12 mm
.4724 in
19 mm
19 mm
1/2 in
.500 in
3/4 in
13/16 in
14 mm
.5512 in
22 mm
22 mm
9/16 in
.5625 in
7/8 in
7/8 in
16 mm
.6299 in
24 mm
24 mm
5/8 in
.625 in
15/16 in
1 in
18 mm
.7087 in
27 mm
27 mm
3/4 in
.750 in
1-1/8 in
1-1/8 in
22 mm
.8661 in
32 mm
32 mm
7/8 in
.875 in
1-5/16 in
1-5/16 in
24 mm
.9449 in
36 mm
36 mm
1 in
1.000 in
1-1/2 in
1-1/2 in
Notes
Notes
Warranty
Effective January 1, 2015
(Equipment with a serial number preface of MF or newer)
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions 5. 6 Months — Parts
below, warrants to its original retail purchaser that new equipment
* Batteries
sold after the effective date of this limited warranty is free of defects
* Bernard Guns (No Labor)
in material and workmanship at the time it is shipped from factory.
* Tregaskiss Guns (No Labor)
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE 6. 90 Days — Parts
* Accessory (Kits)
WARRANTIES OF MERCHANTABILITY AND FITNESS.
* Canvas Covers
Within the warranty periods listed below, manufacturer will repair or
* Induction Heating Coils and Blankets, Cables, and
replace any warranted parts or components that fail due to such
Non-Electronic Controls
defects in material or workmanship. Manufacturer must be notified
* M-Guns
in writing within thirty (30) days of such defect or failure, at which
* MIG Guns and Subarc (SAW) Torches
time manufacturer will provide instructions on the warranty claim
* Remote Controls and RFCS-RJ45
procedures to be followed. If notification is submitted as an online
* Replacement Parts (No labor)
warranty claim, the claim must include a detailed description of the
* Roughneck Guns
fault and the troubleshooting steps taken to identify failed
components and the cause of their failure.
* Spoolmate Spoolguns
Manufacturer shall honor warranty claims on warranted equipment
listed below in the event of such a failure within the warranty time
periods. All warranty time periods start on the delivery date of the
equipment to the original end-user purchaser, and not to exceed
twelve months after the equipment is shipped to the distributor.
1.
2.
3.
4.
5 Years Parts — 3 Years Labor
* Original Main Power Rectifiers Only to Include SCRs,
Diodes, and Discrete Rectifier Modules
3 Years — Parts and Labor
* Auto-Darkening Helmet Lenses (Except Classic
Series) (No Labor)
* Engine Driven Welder/Generators
(NOTE: Engines are Warranted Separately by the
Engine Manufacturer.)
* Inverter Power Sources (Unless Otherwise Stated)
* Plasma Arc Cutting Power Sources
* Process Controllers
* Semi-Automatic and Automatic Wire Feeders
* Transformer/Rectifier Power Sources
2 Years — Parts and Labor
* Auto-Darkening Helmet Lenses − Classic Series Only
(No Labor)
* Fume Extractors − Capture 5, Filtair 400 and Industrial
Collector Series
1 Year — Parts and Labor Unless Specified
* Automatic Motion Devices
* CoolBelt and CoolBand Blower Unit (No Labor)
* Desiccant Air Dryer System
* External Monitoring Equipment and Sensors
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Field Options
(NOTE: Field options are covered for the
remaining warranty period of the product they are
installed in, or for a minimum of one year —
whichever is greater.)
RFCS Foot Controls (Except RFCS-RJ45)
Fume Extractors − Filtair 130, MWX and SWX Series
HF Units
ICE/XT Plasma Cutting Torches (No Labor)
Induction Heating Power Sources, Coolers
(NOTE: Digital Recorders are Warranted
Separately by the Manufacturer.)
LiveArc Welding Performance Management System
Load Banks
Motor-Driven Guns (except Spoolmate Spoolguns)
PAPR Blower Unit (No Labor)
Positioners and Controllers
Racks
Running Gear/Trailers
Spot Welders
Subarc Wire Drive Assemblies
Water Coolant Systems
TIG Torches (No Labor)
Wireless Remote Foot/Hand Controls and Receivers
Work Stations/Weld Tables (No Labor)
Limited Warranty shall not apply to:
1.
2.
3.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, relays, work
station table tops and welding curtains, or parts that
fail due to normal wear. (Exception: brushes and
relays are covered on all engine-driven products.)
Items furnished by manufacturer, but manufactured by
others, such as engines or trade accessories. These
items are covered by the manufacturer’s warranty, if any.
Equipment that has been modified by any party other than
manufacturer, or equipment that has been improperly
installed, improperly operated or misused based upon
industry standards, or equipment which has not had
reasonable and necessary maintenance, or equipment
which has been used for operation outside of the
specifications for the equipment.
MANUFACTURER’S PRODUCTS ARE INTENDED FOR
PURCHASE AND USE BY COMMERCIAL/INDUSTRIAL USERS
AND PERSONS TRAINED AND EXPERIENCED IN THE USE
AND MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at manufacturer’s option: (1) repair; or
(2) replacement; or, where authorized in writing by manufacturer in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized service station; or (4) payment of or
credit for the purchase price (less reasonable depreciation based
upon actual use) upon return of the goods at customer’s risk and
expense. Manufacturer’s option of repair or replacement will be
F.O.B., Factory at Appleton, Wisconsin, or F.O.B. at an authorized
service facility as determined by manufacturer. Therefore no
compensation or reimbursement for transportation costs of any
kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MANUFACTURER BE
LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY
OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION, OPERATION OF LAW,
CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO
ANY AND ALL EQUIPMENT FURNISHED BY MANUFACTURER
IS EXCLUDED AND DISCLAIMED BY MANUFACTURER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein, and
to the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available, but
may vary from province to province.
brand_warr 2015-01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Purchase Date
Serial/Style Number
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Contact the Delivering Carrier for:
Zip
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims,
contact your distributor and/or equipment
manufacturer’s Transportation Department.
ORIGINAL INSTRUCTIONS − PRINTED IN USA
2015-01