Miller | MB520506A | Owner Manual | Miller INVISION 352 MPA AUTO-LINE CE User manual

Miller INVISION 352 MPA AUTO-LINE CE User manual
OM-245 171D
2011−12
Processes
MIG (GMAW) and Pulsed MIG
(GMAW-P) Welding
Description
Arc Welding Power Source
™
Invision 352 MPa
Auto-Line
™
CE
File: MULTIPROCESS
Visit our website at
www.MillerWelds.com
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001 Quality System Warranty and service information for your
Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual specification sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 2009−09
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Symboles utilisés . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance . . . . . .
2-4. Proposition californienne 65 Avertissements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6. Informations relatives aux CEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Warning Label Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. WEEE Label (For Products Sold Within The EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3. Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Features And Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Arc Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Important Information Regarding CE Products (Sold Within The EU) . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Serial Number And Rating Label Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Dimensions And Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Selecting a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Weld Output Receptacles And Selecting Cable Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6. Remote 14 Receptacle Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. 115 Volts AC Duplex Receptacle And Supplementary Protectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8. Electrical Service Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-9. Connecting 3-Phase Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − GENERAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Configuration Option Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − GMAW/GMAW-P/FCAW OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Typical Connection For Remote Control Feeder GMAW/GMAW-P/FCAW Process . . . . . . . . . . . . . . .
7-2. MIG Welding Mode - GMAW/FCAW Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3. MIG - Wire and Gas Selection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4. Pulsed MIG Welding Mode - GMAW-P Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5. Pulsed MIG - Wire and Gas Selection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-6. Remote Process Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − MAINTENANCE & TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2. Blowing Out Inside Of Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-3. Help Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-4. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION −10 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY
1
1
1
3
4
4
4
5
5
5
7
8
9
9
11
11
13
13
14
14
14
14
15
16
16
16
16
17
18
19
19
20
21
22
22
23
25
25
26
27
28
29
30
31
31
31
32
33
34
36
DECLARATION OF CONFORMITY
for European Community (CE marked) products.
MILLER Electric Mfg. Co., 1635 Spencer Street, Appleton, WI 54914 U.S.A. declares that the
product(s) identified in this declaration conform to the essential requirements and provisions of
the stated Council Directive(s) and Standard(s).
Product/Apparatus Identification:
Product
Invision 352 Mpa CE
Stock Number
907431002
Council Directives:
• 2006/95/EC Low Voltage
• 2004/108/EC Electromagnetic Compatibility
Standards:
• IEC 60974­1:2005 Arc welding equipment – Part 1: Welding power sources
• IEC 60974­10:2007 Arc Welding Equipment – Part 10: Electromagnetic compatibility (EMC) requirements
• EN 50445:2008 Product family standard to demonstrate compliance of equipment for resistance welding,
arc welding and allied processes with the basic restrictions related to human exposure to electromagnetic
fields (0 Hz – 300Hz)
Signatory:
January 21, 2011
_____________________________________
___________________________________________
David A. Werba
Date of Declaration
MANAGER, PRODUCT DESIGN COMPLIANCE
245174A
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som 2011−10
7
Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.
1-1. Symbol Usage
DANGER! − Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in the text.
NOTICE − Indicates statements not related to personal injury.
. Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the
hazards.
1-2. Arc Welding Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information
found in the Safety Standards listed in Section 1-5. Read and
follow all Safety Standards.
Only qualified persons should install, operate, maintain, and
repair this unit.
During operation, keep everybody, especially children, away.
D Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
D When making input connections, attach proper grounding conductor first − double-check connections.
D Keep cords dry, free of oil and grease, and protected from hot metal
and sparks.
D Frequently inspect input power cord for damage or bare wiring −
replace cord immediately if damaged − bare wiring can kill.
D Turn off all equipment when not in use.
D Do not use worn, damaged, undersized, or poorly spliced cables.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic
wire welding, the wire, wire reel, drive roll housing,
and all metal parts touching the welding wire are
electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
D Do not touch live electrical parts.
D Wear dry, hole-free insulating gloves and body protection.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
D Use AC output ONLY if required for the welding process.
D If AC output is required, use remote output control if present on
unit.
D Additional safety precautions are required when any of the following electrically hazardous conditions are present: in damp
locations or while wearing wet clothing; on metal structures such
as floors, gratings, or scaffolds; when in cramped positions such
as sitting, kneeling, or lying; or when there is a high risk of unavoidable or accidental contact with the workpiece or ground. For these
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone!
D Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
D Properly install, ground, and operate this equipment according to
its Owner’s Manual and national, state, and local codes.
D Do not drape cables over your body.
D If earth grounding of the workpiece is required, ground it directly
with a separate cable.
D Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
D Do not touch electrode holders connected to two welding machines at the same time since double open-circuit voltage will be
present.
D Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
D Wear a safety harness if working above floor level.
D Keep all panels and covers securely in place.
D Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
D Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
D Do not connect more than one electrode or work cable to any
single weld output terminal. Disconnect cable for process not in
use.
SIGNIFICANT DC VOLTAGE exists in inverter welding power sources AFTER removal of input power.
D Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
HOT PARTS can burn.
D Do not touch hot parts bare handed.
D Allow cooling period before working on equipment.
D To handle hot parts, use proper tools and/or
wear heavy, insulated welding gloves and
clothing to prevent burns.
OM-245 171 Page 1
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D Keep your head out of the fumes. Do not breathe the fumes.
D If inside, ventilate the area and/or use local forced ventilation at the
arc to remove welding fumes and gases.
D If ventilation is poor, wear an approved air-supplied respirator.
D Read and understand the Material Safety Data Sheets (MSDSs)
and the manufacturer’s instructions for metals, consumables,
coatings, cleaners, and degreasers.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
D Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements
can give off toxic fumes if welded.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear an approved welding helmet fitted with a proper shade of
filter lenses to protect your face and eyes from arc rays and
sparks when welding or watching (see ANSI Z49.1 and Z87.1
listed in Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash,
glare and sparks; warn others not to watch the arc.
D Wear protective clothing made from durable, flame-resistant
material (leather, heavy cotton, or wool) and foot protection.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D Do not weld where flying sparks can strike flammable material.
D Protect yourself and others from flying sparks and hot metal.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D Do not weld on containers that have held combustibles, or on
closed containers such as tanks, drums, or pipes unless they are
properly prepared according to AWS F4.1 and AWS A6.0 (see
Safety Standards).
D Do not weld where the atmosphere may contain flammable dust,
gas, or liquid vapors (such as gasoline).
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock, sparks, and fire
hazards.
D Do not use welder to thaw frozen pipes.
OM-245 171 Page 2
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
D Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
D After completion of work, inspect area to ensure it is free of sparks,
glowing embers, and flames.
D Use only correct fuses or circuit breakers. Do not oversize or bypass them.
D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
for hot work and have a fire watcher and extinguisher nearby.
FLYING METAL or DIRT can injure eyes.
D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
D Wear approved safety glasses with side
shields even under your welding helmet.
BUILDUP OF GAS can injure or kill.
D Shut off compressed gas supply when not in use.
D Always ventilate confined spaces or use
approved air-supplied respirator.
ELECTRIC AND MAGNETIC FIELDS (EMF)
can affect Implanted Medical Devices.
D Wearers of Pacemakers and other Implanted
Medical Devices should keep away.
D Implanted Medical Device wearers should consult their doctor
and the device manufacturer before going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating
operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Wear approved ear protection if noise level is
high.
CYLINDERS can explode if damaged.
Compressed gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D Protect compressed gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open flames, sparks, and arcs.
D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Keep cylinders away from any welding or other electrical circuits.
D Never drape a welding torch over a gas cylinder.
D Never allow a welding electrode to touch any cylinder.
D Never weld on a pressurized cylinder − explosion will result.
D Use only correct compressed gas cylinders, regulators, hoses,
and fittings designed for the specific application; maintain them
and associated parts in good condition.
D Turn face away from valve outlet when opening cylinder valve.
D Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D Use the right equipment, correct procedures, and sufficient number of persons to lift and move cylinders.
D Read and follow instructions on compressed gas cylinders,
associated equipment, and Compressed Gas Association (CGA)
publication P-1 listed in Safety Standards.
1-3. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
BATTERY EXPLOSION can injure.
D Do not install or place unit on, over, or near
combustible surfaces.
D Do not install unit near flammables.
D Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
D Do not use welder to charge batteries or jump
start vehicles unless it has a battery charging
feature designed for this purpose.
MOVING PARTS can injure.
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
FALLING EQUIPMENT can injure.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are long enough to
extend beyond opposite side of unit.
D Keep equipment (cables and cords) away from moving vehicles
when working from an aerial location.
D Follow the guidelines in the Applications Manual for the Revised
NIOSH Lifting Equation (Publication No. 94−110) when manually lifting heavy parts or equipment.
OVERUSE can cause OVERHEATING
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
D Have only qualified persons remove doors, panels, covers, or
guards for maintenance and troubleshooting as necessary.
D Reinstall doors, panels, covers, or guards when maintenance is
finished and before reconnecting input power.
READ INSTRUCTIONS.
D Read and follow all labels and the Owner’s
Manual carefully before installing, operating, or
servicing unit. Read the safety information at
the beginning of the manual and in each
section.
D Use only genuine replacement parts from the manufacturer.
D Perform maintenance and service according to the Owner’s
Manuals, industry standards, and national, state, and local
codes.
H.F. RADIATION can cause interference.
FLYING SPARKS can injure.
D Wear a face shield to protect eyes and face.
D Shape tungsten electrode only on grinder with
proper guards in a safe location wearing proper
face, hand, and body protection.
D Sparks can cause fires — keep flammables away.
STATIC (ESD) can damage PC boards.
D
D
D
D
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
ARC WELDING can cause interference.
MOVING PARTS can injure.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
D
WELDING WIRE can injure.
D Do not press gun trigger until instructed to do
so.
D Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
D
D
D
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
OM-245 171 Page 3
1-4. California Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to
the state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after use.
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Combustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:
800-463-6727, website: www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website:
www.cdc.gov/NIOSH).
1-6. EMF Information
Electric current flowing through any conductor causes localized electric
and magnetic fields (EMF). Welding current creates an EMF field
around the welding circuit and welding equipment. EMF fields may interfere with some medical implants, e.g. pacemakers. Protective
measures for persons wearing medical implants have to be taken. For
example, restrict access for passers−by or conduct individual risk assessment for welders. All welders should use the following procedures
in order to minimize exposure to EMF fields from the welding circuit:
1. Keep cables close together by twisting or taping them, or using a
cable cover.
2. Do not place your body between welding cables. Arrange cables
to one side and away from the operator.
3. Do not coil or drape cables around your body.
OM-245 171 Page 4
4. Keep head and trunk as far away from the equipment in the
welding circuit as possible.
5. Connect work clamp to workpiece as close to the weld as
possible.
6. Do not work next to, sit or lean on the welding power source.
7. Do not weld whilst carrying the welding power source or wire
feeder.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION
fre_som_2011−10
7
Pour écarter les risques de blessure pour vous−même et pour autrui — lire, appliquer et ranger en lieu sûr ces consignes relatives
aux précautions de sécurité et au mode opératoire.
2-1. Symboles utilisés
DANGER! − Indique une situation dangereuse qui si on
l’évite pas peut donner la mort ou des blessures graves.
Les dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
Indique une situation dangereuse qui si on l’évite pas
peut donner la mort ou des blessures graves. Les dangers possibles sont montrés par les symboles joints ou
sont expliqués dans le texte.
NOTE − Indique des déclarations pas en relation avec des blessures
personnelles.
. Indique des instructions spécifiques.
Ce groupe de symboles veut dire Avertissement! Attention! DANGER
DE CHOC ELECTRIQUE, PIECES EN MOUVEMENT, et PIECES
CHAUDES. Consulter les symboles et les instructions ci-dessous y
afférant pour les actions nécessaires afin d’éviter le danger.
2-2. Dangers relatifs au soudage à l’arc
Les symboles représentés ci-dessous sont utilisés dans ce manuel pour attirer l’attention et identifier les dangers possibles. En
présence de l’un de ces symboles, prendre garde et suivre les
instructions afférentes pour éviter tout risque. Les instructions
en matière de sécurité indiquées ci-dessous ne constituent
qu’un sommaire des instructions de sécurité plus complètes
fournies dans les normes de sécurité énumérées dans la Section 2-5. Lire et observer toutes les normes de sécurité.
Seul un personnel qualifié est autorisé à installer, faire fonctionner, entretenir et réparer cet appareil.
Pendant le fonctionnement, maintenir à distance toutes les
personnes, notamment les enfants de l’appareil.
UNE DÉCHARGE ÉLECTRIQUE peut
entraîner la mort.
Le contact d’organes électriques sous tension peut
provoquer des accidents mortels ou des brûlures
graves. Le circuit de l’électrode et de la pièce est
sous tension lorsque le courant est délivré à la
sortie. Le circuit d’alimentation et les circuits internes de la machine sont également sous tension
lorsque l’alimentation est sur Marche. Dans le mode
de soudage avec du fil, le fil, le dérouleur, le bloc de
commande du rouleau et toutes les parties métalliques en contact avec le fil sont sous tension
électrique. Un équipement installé ou mis à la terre
de manière incorrecte ou impropre constitue un
danger.
D Ne pas toucher aux pièces électriques sous tension.
D Porter des gants isolants et des vêtements de protection secs et
sans trous.
D S’isoler de la pièce à couper et du sol en utilisant des housses ou
des tapis assez grands afin d’éviter tout contact physique avec la
pièce à couper ou le sol.
D Ne pas se servir de source électrique à courant électrique dans les
zones humides, dans les endroits confinés ou là où on risque de
tomber.
D Se servir d’une source électrique à courant électrique UNIQUEMENT si le procédé de soudage le demande.
D Si l’utilisation d’une source électrique à courant électrique s’avère
nécessaire, se servir de la fonction de télécommande si l’appareil
en est équipé.
D D’autres consignes de sécurité sont nécessaires dans les conditions suivantes : risques électriques dans un environnement
humide ou si l’on porte des vêtements mouillés ; sur des structures
métalliques telles que sols, grilles ou échafaudages ; en position
coincée comme assise, à genoux ou couchée ; ou s’il y a un risque
élevé de contact inévitable ou accidentel avec la pièce à souder ou
le sol. Dans ces conditions, utiliser les équipements suivants,
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
dans l’ordre indiqué : 1) un poste à souder DC à tension constante
(à fil), 2) un poste à souder DC manuel (électrode) ou 3) un poste à
souder AC à tension à vide réduite. Dans la plupart des situations,
l’utilisation d’un poste à souder DC à fil à tension constante est recommandée. En outre, ne pas travailler seul !
Couper l’alimentation ou arrêter le moteur avant de procéder à l’installation, à la réparation ou à l’entretien de l’appareil. Déverrouiller
l’alimentation selon la norme OSHA 29 CFR 1910.147 (voir normes de sécurité).
Installez, mettez à la terre et utilisez correctement cet équipement
conformément à son Manuel d’Utilisation et aux réglementations
nationales, gouvernementales et locales.
Toujours vérifier la terre du cordon d’alimentation. Vérifier et
s’assurer que le fil de terre du cordon d’alimentation est bien
raccordé à la borne de terre du sectionneur ou que la fiche du
cordon est raccordée à une prise correctement mise à la terre.
En effectuant les raccordements d’entrée, fixer d’abord le conducteur de mise à la terre approprié et contre-vérifier les connexions.
Les câbles doivent être exempts d’humidité, d’huile et de graisse;
protégez−les contre les étincelles et les pièces métalliques
chaudes.
Vérifier fréquemment le cordon d’alimentation afin de s’assurer
qu’il n’est pas altéré ou à nu, le remplacer immédiatement s’il l’est.
Un fil à nu peut entraîner la mort.
L’équipement doit être hors tension lorsqu’il n’est pas utilisé.
Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante ou mal épissés.
Ne pas enrouler les câbles autour du corps.
Si la pièce soudée doit être mise à la terre, le faire directement
avec un câble distinct.
Ne pas toucher l’électrode quand on est en contact avec la pièce,
la terre ou une électrode provenant d’une autre machine.
Ne pas toucher des porte électrodes connectés à deux machines
en même temps à cause de la présence d’une tension à vide doublée.
N’utiliser qu’un matériel en bon état. Réparer ou remplacer sur-lechamp les pièces endommagées. Entretenir l’appareil conformément à ce manuel.
Porter un harnais de sécurité si l’on doit travailler au-dessus du sol.
S’assurer que tous les panneaux et couvercles sont correctement
en place.
Fixer le câble de retour de façon à obtenir un bon contact métalmétal avec la pièce à souder ou la table de travail, le plus près possible de la soudure.
Isoler la pince de masse quand pas mis à la pièce pour éviter le
contact avec tout objet métallique.
Ne pas raccorder plus d’une électrode ou plus d’un câble de
masse à une même borne de sortie de soudage. Débrancher le
câble pour le procédé non utilisé.
OM-245 171 Page 5
Il reste une TENSION DC NON NÉGLIGEABLE dans
les sources de soudage onduleur UNE FOIS
l’alimentation coupée.
D Arrêter les convertisseurs, débrancher le courant électrique et
décharger les condensateurs d’alimentation selon les instructions
indiquées dans la partie Entretien avant de toucher les pièces.
LES PIÈCES CHAUDES peuvent
provoquer des brûlures.
D Ne pas toucher à mains nues les parties
chaudes.
D Prévoir une période de refroidissement avant de
travailler à l’équipement.
D Ne pas toucher aux pièces chaudes, utiliser les outils recommandés et porter des gants de soudage et des vêtements épais pour
éviter les brûlures.
LE SOUDAGE peut provoquer un
incendie ou une explosion.
Le soudage effectué sur des conteneurs fermés tels
que des réservoirs, tambours ou des conduites peut
provoquer leur éclatement. Des étincelles peuvent
être projetées de l’arc de soudure. La projection d’étincelles, des
pièces chaudes et des équipements chauds peut provoquer des
incendies et des brûlures. Le contact accidentel de l’électrode avec
des objets métalliques peut provoquer des étincelles, une explosion,
un surchauffement ou un incendie. Avant de commencer le soudage,
vérifier et s’assurer que l’endroit ne présente pas de danger.
D Déplacer toutes les substances inflammables à une distance de
10,7 m de l’arc de soudage. En cas d’impossibilité les recouvrir
soigneusement avec des protections homologués.
D Ne pas souder dans un endroit là où des étincelles peuvent tomber
sur des substances inflammables.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
D Se protéger et d’autres personnes de la projection d’étincelles et
de métal chaud.
Le soudage génère des fumées et des gaz. Leur
inhalation peut être dangereux pour votre santé.
D Des étincelles et des matériaux chauds du soudage peuvent
facilement passer dans d’autres zones en traversant de petites
fissures et des ouvertures.
D Eloigner votre tête des fumées. Ne pas respirer les fumées.
D Surveiller tout déclenchement d’incendie et tenir un extincteur à
proximité.
D À l’intérieur, ventiler la zone et/ou utiliser une ventilation forcée au
niveau de l’arc pour l’évacuation des fumées et des gaz de
soudage.
D Le soudage effectué sur un plafond, plancher, paroi ou séparation
peut déclencher un incendie de l’autre côté.
D Si la ventilation est médiocre, porter un respirateur anti-vapeurs
approuvé.
D Lire et comprendre les spécifications de sécurité des matériaux
(MSDS) et les instructions du fabricant concernant les métaux, les
consommables, les revêtements, les nettoyants et les dégraisseurs.
D Travailler dans un espace fermé seulement s’il est bien ventilé ou
en portant un respirateur à alimentation d’air. Demander toujours à
un surveillant dûment formé de se tenir à proximité. Des fumées et
des gaz de soudage peuvent déplacer l’air et abaisser le niveau
d’oxygène provoquant des blessures ou des accidents mortels.
S’assurer que l’air de respiration ne présente aucun danger.
D Ne pas souder dans des endroits situés à proximité d’opérations
de dégraissage, de nettoyage ou de pulvérisation. La chaleur et
les rayons de l’arc peuvent réagir en présence de vapeurs et former des gaz hautement toxiques et irritants.
D Ne pas souder des métaux munis d’un revêtement, tels que l’acier
galvanisé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait été enlevé dans la zone de soudure, que l’endroit soit
bien ventilé, et en portant un respirateur à alimentation d’air. Les
revêtements et tous les métaux renfermant ces éléments peuvent
dégager des fumées toxiques en cas de soudage.
LES RAYONS DE L’ARC peuvent
provoquer des brûlures dans les
yeux et sur la peau.
Le rayonnement de l’arc du procédé de soudage
génère des rayons visibles et invisibles intenses
(ultraviolets et infrarouges) susceptibles de provoquer des brûlures
dans les yeux et sur la peau. Des étincelles sont projetées pendant le
soudage.
D Porter un casque de soudage approuvé muni de verres filtrants
approprié pour protéger visage et yeux pour protéger votre visage
et vos yeux pendant le soudage ou pour regarder (voir ANSI Z49.1
et Z87.1 énuméré dans les normes de sécurité).
D Porter des lunettes de sécurité avec écrans latéraux même sous
votre casque.
D Avoir recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements les éblouissements
et les étincelles ; prévenir toute personne sur les lieux de ne pas
regarder l’arc.
D Porter des vêtements confectionnés avec des matières résistantes et ignifuges (cuir, coton lourd ou laine) et des bottes de
protection.
OM-245 171 Page 6
D Ne pas effectuer le soudage sur des conteneurs fermés tels que
des réservoirs, tambours, ou conduites, à moins qu’ils n’aient été
préparés correctement conformément à AWS F4.1 et AWS A6.0
(voir les Normes de Sécurité).
D Ne soudez pas si l’air ambiant est chargé de particules, gaz, ou vapeurs inflammables (vapeur d’essence, par exemple).
D Brancher le câble de masse sur la pièce le plus près possible de la
zone de soudage pour éviter le transport du courant sur une
longue distance par des chemins inconnus éventuels en provoquant des risques d’électrocution, d’étincelles et d’incendie.
D Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
D En cas de non utilisation, enlever la baguette d’électrode du porteélectrode ou couper le fil à la pointe de contact.
D Porter des vêtements de protection dépourvus d’huile tels que des
gants en cuir, une chemise en matériau lourd, des pantalons sans
revers, des chaussures hautes et un couvre chef.
D Avant de souder, retirer toute substance combustible de vos poches telles qu’un allumeur au butane ou des allumettes.
D Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
D Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
D Suivre les recommandations dans OSHA 1910.252(a)(2)(iv) et
NFPA 51B pour les travaux à chaud et avoir de la surveillance et un
extincteur à proximité.
DES PIECES DE METAL ou DES
SALETES peuvent provoquer des
blessures dans les yeux.
D Le soudage, l’écaillement, le passage de la pièce à la brosse en
fil de fer, et le meulage génèrent des étincelles et des particules
métalliques volantes. Pendant la période de refroidissement des
soudures, elles risquent de projeter du laitier.
D Porter des lunettes de sécurité avec écrans latéraux ou un écran
facial.
LES ACCUMULATIONS DE GAZ
risquent de provoquer des blessures
ou même la mort.
D Fermer l’alimentation du gaz comprimé en cas
de non utilisation.
D Veiller toujours à bien aérer les espaces confinés ou se servir d’un respirateur d’adduction
d’air homologué.
Les CHAMPS ÉLECTROMAGNÉTIQUES (CEM)
peuvent affecter les implants médicaux.
D Les porteurs de stimulateurs cardiaques et
autres implants médicaux doivent rester à
distance.
D Les porteurs d’implants médicaux doivent consulter leur
médecin et le fabricant du dispositif avant de s’approcher de la
zone où se déroule du soudage à l’arc, du soudage par points, du
gougeage, de la découpe plasma ou une opération de chauffage
par induction.
LE BRUIT peut endommager l’ouïe.
Le bruit des processus et des équipements peut
affecter l’ouïe.
D Porter des protections approuvées pour les
oreilles si le niveau sonore est trop élevé.
LES BOUTEILLES peuvent exploser
si elles sont endommagées.
Les bouteilles de gaz comprimé contiennent du gaz
sous haute pression. Si une bouteille est
endommagée, elle peut exploser. Du fait que les
bouteilles de gaz font normalement partie du
procédé de soudage, les manipuler avec
précaution.
D Protéger les bouteilles de gaz comprimé d’une chaleur excessive,
des chocs mécaniques, des dommages physiques, du laitier, des
flammes ouvertes, des étincelles et des arcs.
D Placer les bouteilles debout en les fixant dans un support stationnaire ou dans un porte-bouteilles pour les empêcher de tomber ou
de se renverser.
D Tenir les bouteilles éloignées des circuits de soudage ou autres
circuits électriques.
D Ne jamais placer une torche de soudage sur une bouteille à gaz.
D Une électrode de soudage ne doit jamais entrer en contact avec
une bouteille.
D Ne jamais souder une bouteille pressurisée − risque d’explosion.
D Utiliser seulement des bouteilles de gaz comprimé, régulateurs,
tuyaux et raccords convenables pour cette application spécifique;
les maintenir ainsi que les éléments associés en bon état.
D Détourner votre visage du détendeur-régulateur lorsque vous
ouvrez la soupape de la bouteille.
D Le couvercle du détendeur doit toujours être en place, sauf lorsque
la bouteille est utilisée ou qu’elle est reliée pour usage ultérieur.
D Utiliser les équipements corrects, les bonnes procédures et suffisamment de personnes pour soulever et déplacer les bouteilles.
D Lire et suivre les instructions sur les bouteilles de gaz comprimé,
l’équipement connexe et le dépliant P-1 de la CGA (Compressed
Gas Association) mentionné dans les principales normes de sécurité.
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance
Risque D’INCENDIE OU
D’EXPLOSION.
D Ne pas placer l’appareil sur, au-dessus ou
à proximité de surfaces inflammables.
D Ne pas installer l’appareil à proximité de produits inflammables.
D Ne pas surcharger l’installation électrique − s’assurer que
l’alimentation est correctement dimensionnée et protégée avant
de mettre l’appareil en service.
LA CHUTE DE L’ÉQUIPEMENT peut
provoquer des blessures.
D Utiliser l’anneau de levage uniquement pour
soulever l’appareil, NON PAS les chariots, les
bouteilles de gaz ou tout autre accessoire.
D Utiliser un équipement de levage de capacité
suffisante pour lever l’appareil.
D En utilisant des fourches de levage pour déplacer l’unité, s’assurer que les fourches sont suffisamment longues pour dépasser
du côté opposé de l’appareil.
D Tenir l’équipement (câbles et cordons) à distance des véhicules
mobiles lors de toute opération en hauteur.
D Suivre les consignes du Manuel des applications pour l’équation
de levage NIOSH révisée (Publication Nº94–110) lors du levage
manuelle de pièces ou équipements lourds.
L’EMPLOI
EXCESSIF
peut
SURCHAUFFER L’ÉQUIPEMENT.
D Prévoir une période de refroidissement ; respecter le cycle opératoire nominal.
D Réduire le courant ou le facteur de marche
avant de poursuivre le soudage.
D Ne pas obstruer les passages d’air du poste.
LES ÉTINCELLES PROJETÉES
peuvent provoquer des blessures.
D Porter un écran facial pour protéger le visage et
les yeux.
D Affûter l’électrode au tungstène uniquement à la
meuleuse dotée de protecteurs. Cette
manœuvre est à exécuter dans un endroit sûr
lorsque l’on porte l’équipement homologué de
protection du visage, des mains et du corps.
D Les étincelles risquent de causer un incendie − éloigner toute substance inflammable.
LES CHARGES ÉLECTROSTATIQUES peuvent endommager les circuits imprimés.
D Établir la connexion avec la barrette de terre
avant de manipuler des cartes ou des pièces.
D Utiliser des pochettes et des boîtes antistatiques pour stocker, déplacer ou expédier des
cartes de circuits imprimes.
OM-245 171 Page 7
Les PIÈCES MOBILES peuvent
causer des blessures.
LE
RAYONNEMENT
HAUTE
FRÉQUENCE
(H.F.)
risque
de
provoquer des interférences.
D Ne pas s’approcher des organes mobiles.
D Ne pas s’approcher des points de coincement
tels que des rouleaux de commande.
D Le rayonnement haute fréquence (H.F.) peut
provoquer des interférences avec les équipements de radio−navigation et de communication, les services de sécurité et les ordinateurs.
LES FILS DE SOUDAGE peuvent
provoquer des blessures.
D Ne pas appuyer sur la gâchette avant d’en
avoir reçu l’instruction.
D Ne pas diriger le pistolet vers soi, d’autres
personnes ou toute pièce mécanique en
engageant le fil de soudage.
L’EXPLOSION DE LA BATTERIE
peut provoquer des blessures.
D Ne pas utiliser l’appareil de soudage pour
charger des batteries ou faire démarrer
des véhicules à l’aide de câbles de démarrage,
sauf si l’appareil dispose d’une fonctionnalité
de charge de batterie destinée à cet usage.
D Demander seulement à des personnes qualifiées familiarisées
avec des équipements électroniques de faire fonctionner l’installation.
D L’utilisateur est tenu de faire corriger rapidement par un électricien
qualifié les interférences résultant de l’installation.
D Si le FCC signale des interférences, arrêter immédiatement l’appareil.
D Effectuer régulièrement le contrôle et l’entretien de l’installation.
D Maintenir soigneusement fermés les portes et les panneaux des
sources de haute fréquence, maintenir les éclateurs à une distance correcte et utiliser une terre et un blindage pour réduire les
interférences éventuelles.
Les PIÈCES MOBILES peuvent
causer des blessures.
D S’abstenir de toucher des organes mobiles tels
que des ventilateurs.
D Maintenir fermés et verrouillés les portes,
panneaux, recouvrements et dispositifs de
protection.
D Lorsque cela est nécessaire pour des travaux d’entretien et de
dépannage, faire retirer les portes, panneaux, recouvrements
ou dispositifs de protection uniquement par du personnel qualifié.
D Remettre les portes, panneaux, recouvrements ou dispositifs de
protection quand l’entretien est terminé et avant de rebrancher
l’alimentation électrique.
LIRE LES INSTRUCTIONS.
D Lire et appliquer les instructions sur les
étiquettes et le Mode d’emploi avant l’installation, l’utilisation ou l’entretien de l’appareil.
Lire les informations de sécurité au début du
manuel et dans chaque section.
D N’utiliser que les pièces de rechange recommandées par le
constructeur.
D Effectuer l’entretien en respectant les manuels d’utilisation, les
normes industrielles et les codes nationaux, d’état et locaux.
LE SOUDAGE À L’ARC risque de
provoquer des interférences.
D
D
D
D
D
D L’énergie électromagnétique risque de
provoquer des interférences pour l’équipement
électronique sensible tel que les ordinateurs et
l’équipement commandé par ordinateur tel que
les robots.
Veiller à ce que tout l’équipement de la zone de soudage soit
compatible électromagnétiquement.
Pour réduire la possibilité d’interférence, maintenir les câbles de
soudage aussi courts que possible, les grouper, et les poser
aussi bas que possible (ex. par terre).
Veiller à souder à une distance de 100 mètres de tout équipement électronique sensible.
Veiller à ce que ce poste de soudage soit posé et mis à la terre
conformément à ce mode d’emploi.
En cas d’interférences après avoir pris les mesures précédentes, il incombe à l’utilisateur de prendre des mesures supplémentaires telles que le déplacement du poste, l’utilisation de câbles blindés, l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone de travail.
2-4. Proposition californienne 65 Avertissements
Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des malformations congénitales et, dans certains cas, des cancers.
(Code de santé et de sécurité de Californie, chapitre 25249.5
et suivants)
OM-245 171 Page 8
Ce produit contient des produits chimiques, notamment du
plomb, dont l’État de Californie reconnaît qu’ils provoquent
des cancers, des malformations congénitales ou d’autres
problèmes de procréation. Se laver les mains après
utilisation.
2-5. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Combustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:
800-463-6727, website: www.csa-international.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website:
www.cdc.gov/NIOSH).
2-6. Informations relatives aux CEM
Le courant électrique qui traverse tout conducteur génère des champs
électromagnétiques (CEM) à certains endroits. Le courant de soudage
crée un CEM autour du circuit et du matériel de soudage. Les CEM
peuvent créer des interférences avec certains implants médicaux
comme des stimulateurs cardiaques. Des mesures de protection pour
les porteurs d’implants médicaux doivent être prises: Limiter par
exemple tout accès aux passants ou procéder à une évaluation des
risques individuels pour les soudeurs. Tous les soudeurs doivent
appliquer les procédures suivantes pour minimiser l’exposition aux
CEM provenant du circuit de soudage:
4. Maintenir la tête et le torse aussi loin que possible du matériel du
circuit de soudage.
1. Rassembler les câbles en les torsadant ou en les attachant avec
du ruban adhésif ou avec une housse.
2. Ne pas se tenir au milieu des câbles de soudage. Disposer les
câbles d’un côté et à distance de l’opérateur.
3. Ne pas courber et ne pas entourer les câbles autour de votre
corps.
En ce qui concerne les implants médicaux :
5. Connecter la pince sur la pièce aussi près que possible de la
soudure.
6. Ne pas travailler à proximité d’une source de soudage, ni
s’asseoir ou se pencher dessus.
7. Ne pas souder tout en portant la source de soudage ou le
dévidoir.
Les porteurs d’implants doivent d’abord consulter leur médecin avant
de s’approcher des opérations de soudage à l’arc, de soudage par
points, de gougeage, du coupage plasma ou de chauffage par induction. Si le médecin approuve, il est recommandé de suivre les
procédures précédentes.
OM-245 171 Page 9
OM-245 171 Page 10
SECTION 3 − DEFINITIONS
3-1. Warning Label Definitions
Warning! Watch Out! There are possible
hazards as shown by the symbols.
1
Electric shock from welding electrode
or wiring can kill.
2
2.1
2.2
1.1 Wear dry insulating gloves. Do not
touch electrode with bare hand. Do
not wear wet or damaged gloves.
2.3
3
1.2 Protect yourself from electric shock by
insulating yourself from work and
ground.
3.1
3.2
1.3 Disconnect input plug or power before
working on machine.
1
1.1
2
2.1
1.2
2.2
Breathing welding fumes can be
hazardous to your health.
Keep your head out of the fumes.
Use forced ventilation or local exhaust
to remove the fumes.
Use ventilating fan to remove fumes.
Welding sparks can cause explosion
or fire.
Keep flammables away from welding.
Do not weld near flammables.
Welding sparks can cause fires. Have
a fire extinguisher nearby, and have a
watchperson ready to use it.
1.3
4
2.3
3.3 Do not weld on drums or any closed
containers.
4
Arc rays can burn eyes and injure
skin.
4.1 Wear hat and safety glasses. Use ear
protection and button shirt collar. Use
welding helmet with correct shade of
filter. Wear complete body protection.
5
Become trained and read the
instructions before working on the
machine or welding.
6
Do not remove or paint over (cover)
the label.
4.1
5
Kasjf;laksf;lkasdf'l;aksdf;lkasd;flksadflkasd;lk
Kasjf;laksf;lkasdf'l;aksdf;lkasd;flksadflkasd;lk
Kasjf;laksf;lkasdf'l;aksdf;lkasd;flksadflkasd;lk
3
3.1
3.2
3.3
6
179310-B
OM-245 171 Page 11
1
2
3
1
2
3
4
5
6
4
V
V
5
>60s
V
219335-C
6
1
2
1
2
3
4
5
3
4
212073-C
5
Warning! Watch Out! There
are possible hazards as
shown by the symbols.
Electric shock from wiring can
kill.
Disconnect input plug or
power before working on
machine.
Hazardous voltage remains
on input capacitors after
power is turned off. Do not
touch fully charged
capacitors.
Always wait 60 seconds after
power is turned off before
working on unit, OR
Check input capacitor voltage,
and be sure it is near 0 before
touching any parts.
Warning! Watch Out! There
are possible hazards as
shown by the symbols.
When power is applied failed
parts can explode or cause
other parts to explode.
Flying pieces of parts can
cause injury. Always wear a
face shield when servicing
unit.
Always wear long sleeves and
button your collar when
servicing unit.
After taking proper
precautions as shown,
connect power to unit.
4/96
1
1
2
3
= < 60°
4
5
179309-C
2
OM-245 171 Page 12
3
4
5
Warning! Watch Out! There
are possible hazards as
shown by the symbols.
Falling equipment can cause
injury and damage to unit.
Always lift and support unit
using both handles. Keep
angle of lifting device less
than 60 degrees.
Use a proper cart to move
unit.
Do not use one handle to lift
or support unit.
3-2. WEEE Label (For Products Sold Within The EU)
Do not discard product (where applicable) with general waste.
Reuse or recycle Waste Electrical
and Electronic Equipment (WEEE)
by disposing at a designated collection facility.
Contact your local recycling office
or your local distributor for further
information.
3-3. Symbols And Definitions
A
Panel
Alternating
Current (AC)
Output
Circuit Breaker
Remote
On
Off
Gas Tungsten Arc
Welding (GTAW)
Negative
Voltage Input
Direct Current
(DC)
Positive
Inductance
Protective Earth
(Ground)
Constant Current
Constant Voltage
Foot Control
Line Connection
Arc Force
Shielded Metal Arc
Welding (SMAW)
Gas Metal Arc
Welding (GMAW)
Three Phase Static
Frequency ConverterTransformerRectifier
U0
Rated No Load
Voltage (Average)
Hz
Hertz
U1
IP
Pulsed
I1max
V
Amperage
Primary Voltage
Degree Of
Protection
U2
I2
Conventional
Load Voltage
Rated Welding
Current
X
%
Voltage
Duty Cycle
Percent
Setup
Single Phase
Three Phase
Maximum Effective
Supply Current
Increase
Lift-Arc Operation
(GTAW)
Scratch Start TIG
Voltage Sensing
Feeder
Arc Control
Gas Type
Wire Type
Welding Arc
Rated Maximum
Supply Current
I1eff
OM-245 171 Page 13
SECTION 4 − INTRODUCTION
4-1. Specifications
Input
Power
3-Phase
Rated Output
350 A at 34
VDC, 60%
Duty Cycle
RMS Amps Input at Rated Load
Output, 50/60 Hz 3-Phase at
NEMA Load Voltages and Class I
Rating
Voltage Range in
CV Mode
Max. Open-Circuit
Voltage
IP Rating
230 V
400 V
460 V
KVA
KW
10−38 V
75 VDC
23
36.1
20.6
17.8
14.2
13.6
*See Section 4-4 for Duty Cycle Rating.
4-2. Features And Benefits
Auto-Linet Power Management Technology is circuitry that automatically adapts the power source to the primary
voltage being applied (see Section 5-9).
LVCt Line Voltage Compensation is circuitry that keeps the power source output constant regardless of input power fluctuation.
Wind Tunnel Technologyt circulates air over components that require cooling, not over electronic circuitry, which
reduces contaminants and improves reliability in harsh welding environments.
Fan-On-Demandt cooling system operates only when needed, reducing noise, energy use and the amount of contaminants pulled through the machine.
Thermal Overload Protection automatically shuts down the unit, only when necessary to prevent damage to internal
components if the duty cycle is exceeded or air flow and cooling are restricted (see Section 4-4).
Auto Remote Sense enables the unit to automatically sense the connection of a remote control.
Synergic Pulsed MIG Operation allows single knob control of the arc. As wirefeed speed is increased or decreased,
the pulse parameters increase or decrease matching the power output to the wire speed (see Section 6-2).
4-3. Arc Controls
Inductance influences the arc stiffness, bead width and appearance, and puddle fluidity in MIG Welding Mode (see
Section 7-2).
SharpArct optimizes the size and shape of the arc cone, bead width and appearance, and puddle fluidity in Pulsed
MIG Welding Mode (see Section 7-4).
OM-245 171 Page 14
4-4. Duty Cycle And Overheating
Duty Cycle is percentage of 10 minutes that unit can weld at rated load
without overheating.
If unit overheats, output stops, a
Help message is displayed and
cooling fan runs. Wait fifteen minutes for unit to cool. Reduce amperage or voltage, or duty cycle before
welding.
NOTICE − Exceeding duty cycle
can damage unit and void warranty.
60% Duty Cycle
6 Minutes Welding
Overheating
4 Minutes Resting
A or V
0
15
Minutes
OR
Reduce Duty Cycle
Ref. 219 523-A
Notes
OM-245 171 Page 15
SECTION 5 − INSTALLATION
5-1. Important Information Regarding CE Products (Sold Within The EU)
A. Information On Electromagnetic Fields (EMF)
!
This equipment shall not be used by the general public as the EMF limits for the general public might be exceeded during welding.
This equipment is built in accordance with EN 60974−1 and is intended to be used only in an occupational environment (where the general public
access is prohibited or regulated in such a way as to be similar to occupational use) by an expert or an instructed person.
Wire feeders and ancillary equipment (such as torches, liquid cooling systems and arc striking and stabilizing devices) as part of the welding
circuit may not be a major contributor to the EMF. See the Owner’s Manuals for all components of the welding circuit for additional EMF exposure
information.
S
S
The EMF assessment on this equipment was conducted at 0.5 meter.
At a distance of 1 meter the EMF exposure values were less than 20% of the permissible values.
ce-emf 1 2010-10
B. Information On Electromagnetic Compatibility (EMC)
!
This Class A equipment is not intended for use in residential locations where the electrical power is provided by the public low−
voltage supply system. There can be potential difficulties in ensuring electromagnetic compatibility in those locations, due to conducted as well as radiated disturbances.
This equipment complies with IEC 61000−3−12 provided that the short−circuit power Ssc is greater than or equal to 4,798,364 at the interface
point between the user’s supply and the public system. It is the responsibility of the installer or user of the equipment to ensure, by consultation
with the distribution network operator if necessary, that the equipment is connected only to a supply with a short−circuit power Ssc greater than
or equal to 4,798,364.
ce-emc 1 2011-09
5-2. Serial Number And Rating Label Location
The serial number and rating information for this product is located on the rear panel. Use rating label to determine input power requirements and/or
rated output. For future reference, write serial number in space provided on back cover of this manual.
5-3. Dimensions And Weight
A
Hole Layout Dimensions
E
F
A
11-3/4 in. (298 mm)
B
1-11/16 in. (42 mm)
C
15-3/4 in. (400 mm)
G
24 in.
(610 mm)
17 in.
(432 mm)
D
C
D
19-3/32 in. (485 mm)
E
8-11/16 in. (221 mm)
F
1-17/32 in. (39 mm)
G
1/4-20 UNC -2B thread
12-1/2 in.
(318 mm)
B
804 801-A
Weight
94.8 lb (43 kg)
OM-245 171 Page 16
5-4. Selecting a Location
1
Lifting Handles
Use handles to lift unit.
2
Movement
3
1
!
1
Hand Cart
Use cart or similar device to move
unit.
Do not move or operate unit
where it could tip.
Line Disconnect Device
Locate unit near correct input
power supply.
!
Special installation may be
required where gasoline or
volatile liquids are present −
see NEC Article 511 or CEC
Section 20.
2
Location
3
18 in.
(460 mm)
18 in.
(460 mm)
XMT Location 1
Notes
OM-245 171 Page 17
5-5. Weld Output Receptacles And Selecting Cable Sizes
NOTICE − The Total Cable Length in Weld Circuit (see table below) is the combined length of both weld cables. For example, if the power source is
100 ft (30 m) from the workpiece, the total cable length in the weld circuit is 200 ft (2 cables x 100 ft). Use the 200 ft (60 m) column to determine cable
size.
Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit
Not Exceeding***
Weld Output
Terminals
!
Turn off power before connecting to
weld output terminals.
!
Do not use worn,
damaged,
undersized, or poorly
spliced cables.
100 ft (30 m) or Less
Welding
Amperes
+
10 − 60%
Duty
Cycle
150 ft
(45 m)
60 − 100%
Duty
Cycle
200 ft
(60 m)
* This
300 ft
(90 m)
350 ft
400 ft
(105 m) (120 m)
10 − 100% Duty Cycle
AWG (mm2)
AWG
(mm2)
AWG (mm2)
100
4 (20)
4 (20)
4 (20)
3 (30)
2 (35)
1 (50)
1/0 (60)
1/0 (60)
150
3 (30)
3 (30)
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
3/0 (95)
200
3 (30)
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
4/0 (120)
250
2 (35)
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0
(2x70)
2x2/0
(2x70)
300
1 (50)
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0
(2x70)
2x3/0
(2x95)
2x3/0
(2x95)
350
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0
(2x70)
2x3/0
(2x95)
2x3/0
(2x95)
2x4/0
(2x120)
400
1/0 (60)
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0
(2x70)
2x3/0
(2x95)
2x4/0
(2x120)
2x4/0
(2x120)
500
2/0 (70)
3/0 (95)
4/0 (120)
2x2/0
(2x70)
2x3/0
(2x95)
2x4/0
(2x120)
3x3/0
(3x95)
3x3/0
(3x95)
600
3/0 (95)
4/0 (120)
2x2/0
(2x70)
2x3/0
(2x95)
2x4/0
(2x120)
3x3/0
(3x95)
3x4/0
(3x120)
3x4/0
(3x120)
−
Output Receptacles
250 ft
(70 m)
chart is a general guideline and may not suit all applications. If cable overheats, use next size larger cable.
**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.
( ) = mm2 for metric use
***For distances longer than those shown in this guide, call a factory applications rep. at 920-735-4505 (Miller) or 1-800-332-3281 (Hobart).
Ref. S-0007-J 2011−07
OM-245 171 Page 18
5-6. Remote 14 Receptacle Information
Socket*
Socket Information
A
24 volts AC. Protected by supplementary protector CB2.
B
Contact closure to A completes 24 volts AC
contactor control circuit.
I
115 volts AC. Protected by supplementary protector CB1.
J
Contact closure to I completes 115 volts AC
contactor control circuit.
C
Output to remote control; 0 to +10 volts DC, +10
volts DC in MIG mode.
D
Remote control circuit common.
E
0 to +10 volts DC input command signal from
remote control.
L
Wirefeed speed command, 0 to +10 volts DC output signal from wirefeeder.
M
CC/CV Select 0 to +10 volts DC
N
Wirefeed speed common.
A/V
F
Current feedback; +1 volt DC per 100 amperes.
AMPERAGE
VOLTAGE
H
Voltage feedback; +1 volt DC per 10 output receptacle volts.
G
Circuit common for 24 and 115 volts AC circuits.
K
Chassis common.
24 VOLTS AC
A
B
K
J
115 VOLTS AC
I
H
C L N
D M
G
E F
REMOTE
OUTPUT
CONTROL
GND
*The remaining sockets are not used.
5-7. 115 Volts AC Duplex Receptacle And Supplementary Protectors
1
115 V 60 Hz 10 Amp AC
Receptacle
Power is shared between duplex
receptacle and Remote 14 receptacle (see Section 5-6).
1
2
3
Supplementary Protector CB1
Supplementary Protector CB2
CB1 protects duplex receptacle
and 115 volts AC portion of Remote
14 receptacle from overload.
CB2 protects 24 volts AC portion
of Remote 14 receptacle from
overload.
Press button to reset supplementary protector.
2
3
803 691-C
OM-245 171 Page 19
5-8. Electrical Service Guide
NOTICE − INCORRECT INPUT POWER can damage this welding power source. Phase to ground voltage shall not exceed +10% of rated input
voltage.
NOTICE − Actual input voltage should not be 10% less than minimum and/or 10% more than maximum input voltages listed in table. If actual input
voltage is outside this range, output may not be be available.
Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommendations are for a dedicated circuit sized for the rated output and duty cycle of the welding power source.
In dedicated circuit installations, the National Electrical Code (NEC) allows the receptacle or conductor rating to be less than the rating
of the circuit protection device. All components of the circuit must be physically compatible. See NEC articles 210.21, 630.11, and
630.12.
50/60 Hz Three Phase
Input Voltage (V)
230
380
400
460
Input Amperes (A) At Rated Output
36.1
22.3
20.6
17.8
40
25
25
20
50
30
30
25
10
12
12
14
96
(29)
158
(48)
175
(53)
150
(46)
10
12
12
14
Max Recommended Standard Fuse Rating In
Amperes 1
Time-Delay Fuses 2
Normal Operating Fuses 3
Min Input Conductor Size In AWG
4
Max Recommended Input Conductor Length In
Feet (Meters)
Min Grounding Conductor Size In AWG 4
Reference: 2011 National Electrical Code (NEC) (including article 630)
1 If a circuit breaker is used in place of a fuse, choose a circuit breaker with time-current curves comparable to the recommended fuse.
2 “Time-Delay” fuses are UL class “RK5”. See UL 248.
3 “Normal Operating” (general purpose - no intentional delay) fuses are UL class “K5” (up to and including 60 amps), and UL class “H” ( 65 amps and
above).
4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table
310.15(B)(16). If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable
requirements.
Notes
OM-245 171 Page 20
5-9. Connecting 3-Phase Input Power
!
Installation must meet all National
and Local Codes − have only qualified persons make this installation.
!
Disconnect and lockout/tagout input power before connecting input
conductors from unit.
!
Always connect green or green/
yellow conductor to supply
grounding terminal first, and never to a line terminal.
3
= GND/PE Earth Ground
4
. The Auto-Line circuitry in this unit au-
tomatically adapts the power source
to the primary voltage being applied.
Check input voltage available at site.
This unit can be connected to any input power between 208 and 575 VAC
without removing cover to relink the
power source.
7
2
See rating label on unit and check input
voltage available at site.
For Three-Phase Operation
1
2
L1
3
L2
L3
6
5
3
4
5
6
1
Input Power Cord.
Disconnect Device (switch shown in
the OFF position)
Green Or Green/Yellow Grounding
Conductor
Disconnect Device Grounding
Terminal
Input Conductors (L1, L2 And L3)
Disconnect Device Line Terminals
Connect green or green/yellow grounding
conductor to disconnect device grounding
terminal first.
Connect input conductors L1, L2, and L3
to disconnect device line terminals.
7
Overcurrent Protection
Select type and size of overcurrent protection using Section 5-8 (fused disconnect
switch shown).
Close and secure door on disconnect
device. Remove lockout/tagout device,
and place switch in the On position.
Tools Needed:
804 531-A
OM-245 171 Page 21
SECTION 6 − GENERAL OPERATION
6-1. Front Panel
6
4
9
2
3
5
7
8
10
11
12
13
1
16
14
15
. Weld
process operation sections describe functionality of the identified items.
1
Remote 14 Receptacle
2
Output ON Indicator Light
3
Volts Indicator
4
Left Display
5
Arc Length Indicator
OM-245 171 Page 22
Ref. 804 772-A / 245 172-A
6
Right Display
. The meters display the actual weld output
7
8
9
10 Process Indicator
11 Arc Control Indicator
values after arc initiation and remains displayed for approximately three seconds
after the arc is broken.
12 Setup Button
Amps Indicator
Setup Indicator
Adjust Control
14 Power Switch
13 Wire/Gas Type Indicator
15 Weld Output Terminal (−)
16 Weld Output Terminal (+)
6-2. Configuration Option Menu
2
1
SET
3
-UP
4
245 172-A
1 Left Display
2 Right Display
3 Adjustment Control
4 Setup Button
Setup
The Configuration Option Menu provides a
means to customize some machine features
for desired operation.
To enter the Configuration Option Menu, hold
the Setup Button down during power up while
the unit is displaying 8888 on the Left and
Right Displays. SET−UP will be displayed
momentarily.
Configuration options are displayed in the Left
Display. Settings are displayed in the Right
Display. Settings can be changed by turning
the Adjust Control. If a setting does not
change when the Adjust Control is turned, the
option is not configurable. Pressing the Setup
Button moves to the next configuration option.
Notes
OM-245 171 Page 23
6-2
Configuration Option Menu (Continued)
PULS
AUTO
Pulsed MIG Manual/Auto Control
This option sets the Pulsed MIG control as
manual (PULS MAN) or Auto (PULS AUTO)
operation. When set to manual operation, the
arc length setting on power source and wire
speed setting on wire feeder need to be adjusted independently to achieve the desired
arc length. When set to Auto operation, once
arc length is determined it is not necessary to
change the arc length value with changes in
wirefeed speed.
The invision 352 MPa and S-74 MPa are synergic allowing single knob control of the arc.
As wirefeed speed is increased or decreased,
the pulse parameters increase or decrease
matching the power output to the wire speed.
. Auto Operation will only work with the
S-74 MPa wirefeeder. All other wirefeeders will only operate as manual control.
Even when Auto is displayed, operation
will be manual when any other feeder is
connected.
PULS
WFS
ARC.L
MPM
Pulsed MIG Adjustment
This option allows adjusting the Pulsed MIG
process in units of Arc Length (PULS ARC.L)
or preset voltage (PULS VOLT).
Wire Feed Speed And Wire Diameter Units
WFS IPM:
WFS is displayed in inches per minute
Diameter is displayed in inches
WFS MPM:
WFS is displayed in meters per minute
Diameter is displayed in millimeters
INFO
NO
Revision Information
This option identifies the unit’s weld library
(INFO LIB) and firmware revision (INFO
REV).
Press the Setup Button while the unit is displaying INFO LIB to identify the unit’s weld library.
Press the Setup Button while the unit is displaying INFO REV to identify the unit’s firmware revision.
Pressing the Setup Button while the unit is displaying INFO NO will move to the next configuration option.
EXIT
NO
Exit Configuration Option Menu
Press the Setup Button while the unit is displaying EXIT NO to return to the first configuration option. Press the Setup Button while the
unit is displaying EXIT YES to exit the Configuration Option Menu.
. The Configuration Option Menu can be
exited at any time by turning the unit off.
Only if the unit is turned off after EXIT NO
is displayed will configuration option
changes be saved.
OM-245 171 Page 24
SECTION 7 − GMAW/GMAW-P/FCAW OPERATION
7-1. Typical Connection For Remote Control Feeder GMAW/GMAW-P/FCAW Process
9
1
2
3
4
8
7
5
6
804 938-A
5
Workpiece
6
Gun
7
Wire Feeder
Negative (−) Weld Output Terminal
8
Gas Hose
Ground Cable to Workpiece
9
Gas Cylinder
!
Turn off power before making
connections.
1
Remote 14-Receptacle
2
Positive (+) Weld Output Terminal
3
4
Use of shielding gas is dependant on Wire
Type.
. The
connection diagram illustrates
DCEP (reverse polarity) suitable for all
wires except self-shielded FCAW. The
majority of self-shielded FCAW wires
require DCEN (straight polarity).
Notes
OM-245 171 Page 25
7-2. MIG Welding Mode - GMAW/FCAW Process
2
3
4
2 5.0
1
5
6
7
8
Ref. 245 712-A
!
Weld terminals are energized
through the remote control in MIG
welding mode.
1
2
3
4
5
6
7
8
Volts Indicator
Left Display
Right Display
Adjust Control
Process Indicator
Arc Control Indicator
Setup Button
Wire/Gas Indicator
Setup
For typical system connections refer to
Section 7-1.
Press Setup Button twice. The Process Indicator will be lit. Rotate Adjust Control to
select MIG.
Press the Setup Button again. The Wire/
Gas Indicator will be lit. The active wire type
will appear in the Left and Right Display.
Rotate Adjust Control to select desired
wire.
OM-245 171 Page 26
Press the Setup Button again. Wire/Gas Indicator is lit. The active gas type will appear
in the Left and Right Display.
Rotate Adjust Control to select desired gas.
Press the Setup Button to confirm the
selection. The unit will acknowledge a
change of wire and gas information by displaying PROG LOAD momentarily.
. For best results, select the appropriate
Wire and Gas Type to match the actual
wire and gas being used. Refer to the
MIG − Wire and Gas Selection Table
for available wires and gases (see
Section 7-3).
Operation
While the Volts Indicator is lit under the Left
Display, the Adjust Control is used to set
desired preset voltage.
. The preset voltage can be adjusted re-
motely at the wire feeder if the feeder
has a voltage control. This voltage control will override the Adjust Control of
preset voltage on the welding power
source.
Pressing the Setup Button allows adjustment of Arc Control, Wire Type, Gas Type
and preset voltage.
Arc Control (Inductance)
Press the Setup Button until the Arc Control
Indicator is lit. INDU appears on the Left
Display, and the corresponding inductance
setting appears on the Right Display.
Rotate Adjust Control to select desired inductance setting from 0 to 100. Use lower
inductance settings to stiffen the arc and reduce puddle fluidity. Use higher inductance
settings to soften the arc and increase
puddle fluidity.
Refer to the MIG − Wire and Gas Selection
Table (see Section 7-3) for suggested inductance setting for the specific wire and
gas being used.
Press the Setup Button to return to adjustment of preset voltage.
. Each Wire and Gas Type combination
has independent preset voltage and inductance settings. These settings are
preserved when the unit is turned off.
7-3. MIG - Wire and Gas Selection Table
WIRE TYPES**
GAS TYPES
DEFAULT INDUCTANCE
.035 (0.9) STL
.045 (1.2) STL
.052 (1.4) STL
ARGN CO2 (ARGON / CARBON DIOXIDE)
ARGN OXY (ARGON / OXYGEN)
30
.035 (0.9) STL
.045 (1.2) STL
CO2 (CARBON DIOXIDE)
10
Flux Core
.035 (0.9) FCAW
.045 (1.2) FCAW
.052 (1.4) FCAW
1/16 (1.6) FCAW
ARGN CO2 (ARGON / CARBON DIOXIDE) *
CO2 (CARBON DIOXIDE)
30 *
Metal Core
.045 (1.2) MCOR
.052 (1.4) MCOR
1/16 (1.6) MCOR
ARGN CO2 (ARGON / CARBON DIOXIDE)
30
Stainless Steel
.035 (0.9) SSTL
.045 (1.2) SSTL
Steel
TRI MIX (TRI-GAS MIXTURE)
ARGN OXY (ARGON / OXYGEN)
70
.035 (0.9) AL4X (4000 Series)
.040 (1.0) AL4X (4000 Series)
3/64 (1.2) AL4X (4000 Series)
1/16 (1.6) AL4X (4000 Series)
Aluminum
ARGN (ARGON)
10
.035 (0.9) AL5X (5000 Series)
.040 (1.0) AL5X (5000 Series)
3/64 (1.2) AL5X (5000 Series)
1/16 (1.6) AL5X (5000 Series)
*For self-shielded FCAW wires use the ARGN CO2 gas selection and set inductance to less than 10.
**Wire diameter in inches (mm). Refer to section 6-2 to change displayed units.
Notes
OM-245 171 Page 27
7-4. Pulsed MIG Welding Mode - GMAW-P Process
4
3
5
2 5.0
1
2
6
7
8
9
Ref. 245 712-A
!
Weld terminals are energized
through the remote control in
Pulsed MIG welding mode.
1 Volts Indicator
2 Arc Length Indicator
3 Left Display
4 Right Display
5 Adjust Control
6 Process Indicator
7 Arc Control Indicator
8 Setup Button
9 Wire/Gas Indicator
Setup
For typical system connections refer to
Section 7-1.
Press Setup Button twice. The Process Indicator will be lit. Rotate Adjust Control to
select PULS.
Press the Setup Button until the Wire/Gas
Indicator is lit. The active wire type will appear in the Left and Right Display.
Rotate Adjust Control to select desired
wire.
Press the Setup Button again. Wire/Gas Indicator is lit. The active gas type will appear
in the Left and Right Display.
Rotate Adjust Control to select desired gas.
Press the Setup Button again to confirm the
selection. The unit will acknowledge a
change of wire and gas information by displaying PROG LOAD momentarily.
. For best results, select the appropriate
Wire and Gas Type to match the actual
wire and gas being used. Refer to
OM-245 171 Page 28
Pulsed MIG − Wire and Gas Selection
Table for available wires and gases
(see Section 7-5).
Operation
While the Arc Length Indicator is lit under
the Left Display, the Adjust Control is used
to set desired arc length setting.
. The arc length will be adjusted remote-
ly at the wire feeder if the feeder has a
voltage control. This voltage control
will override the Adjust Control on the
welding power source.
Arc Control (SharpArc)
Press the Setup Button until the Arc Control
Indicator is lit. SHRP appears on the Left
Display, and the corresponding SharpArc
setting appears on the Right Display.
Rotate Adjust Control to select desired
SharpArc setting from 0 to 50, default is 25.
Adjusting the SharpArc setting changes the
welding arc cone. Lower settings widen the
arc cone, increases puddle fluidity and flattens the weld bead appearance.
Higher settings narrow the arc cone, reduces puddle fluidity and crowns the weld
bead appearance.
. Each Wire and Gas Type combination
has independent Arc Length and SharpArc settings. These settings are preserved when the unit is turned off.
Arc Length - Pulse MIG Manual Control
(see Section 6-2)
Arc length corresponds to the level of energy needed to burn off the welding electrode.
As wire feed speed increases, a higher arc
length setting is required to burn off the
additional wire. The arc length setting appears in the Left Display when the Arc
Length Indicator is lit. Arc length can be adjusted from 0 to 100.
After the welding output terminals are energized, but prior to arc initiation, the unit displays the letter “R” and a reference wire
speed (IPM) on the Right Display. The reference wire speed can be used as a starting point for the wire speed setting at the
feeder. The wire speed and arc length setting can then be further adjusted to achieve
the desired arc length.
The Configuration Option Menu (see Section 6-2) can be used to change the arc
length setting (0 to 100) to average arc voltage. Average arc voltage can be used as an
alternative method to set the Pulsed MIG
welding arc with the same parameters
(voltage and wire speed) as a conventional
MIG arc. Lower voltage settings correspond to tighter arc lengths while higher
voltage settings correspond to longer arc
lengths. If the voltage mode is selected, the
average voltage preset will be displayed on
the Left Display with the Volts Indicator lit.
Arc Length - Pulse MIG Auto Control
(see Section 6-2)
In Auto operation the arc length setting is
0-100. The programs have been developed
at 50 arc length setting. Increasing or decreasing the arc length setting from 50 will
change the arc length. It is not necessary to
change the arc length value when changing
wire feed speed settings.
. Auto Operation will only work with the
S-74 MPa wirefeeder. All other wirefeeders will only operate as manual control.
7-5. Pulsed MIG - Wire and Gas Selection Table
WIRE TYPES**
GAS TYPES
Steel
.035 (0.9) STL
.045 (1.2) STL
ARGN CO2 (ARGON / CARBON DIOXIDE)
ARGN OXY (ARGON / OXYGEN)
Metal Core
.045 (1.2) MCOR
.052 (1.4) MCOR
ARGN CO2 (ARGON / CARBON DIOXIDE)
Stainless Steel
.035 (0.9) SSTL
.045 (1.2) SSTL
TRI MIX (TRI-GAS MIXTURE)
ARGN OXY (ARGON / OXYGEN)
ARGN CO2 (ARGON / CARBON DIOXIDE)
.035 (0.9) AL4X (4000 Series)
.040 (1.0) AL4X (4000 Series)
3/64 (1.2) AL4X (4000 Series)
1/16 (1.6) AL4X (4000 Series)
Aluminum
ARGN (ARGON)
.035 (0.9) AL5X (5000 Series)
.040 (1.0) AL5X (5000 Series)
3/64 (1.2) AL5X (5000 Series)
1/16 (1.6) AL5X (5000 Series)
ARGN (ARGON)
HE AR25 (HELIUM/ARGON)
Nickel
.035 (0.9) NI
.045 (1.2) NI
ARGN HE (ARGON / HELIUM)
ARGN (ARGON)
Copper Nickel
.035 (0.9) CUNI
.045 (1.2) CUNI
HE ARGN (HELIUM / ARGON)
Silicon Bronze
.035 (0.9) SIBR
.045 (1.2) SIBR
ARGN (ARGON)
**Wire diameter in inches (mm). Refer to section 6-2 to change displayed units.
. Other normal gas mixtures can be used by adjusting arc length and sharp arc. Use the program closest to your gas mixture and wire type and
size.
Notes
OM-245 171 Page 29
7-6. Remote Process Select
This power source can be used with wire
feeders that support Remote Process Select. This feature allows the operator to
switch the active welding process between
MIG and Pulsed MIG at the wire feeder. To
determine if the welding system is Remote
Process Select capable, connect the wire
feeder to the power source and review the
power source display variations shown below.
. When used with an XMT power source,
the Process Select knob must be set to
Pulsed MIG for Remote Process Select
to be active.
Power Source Display − Wire Feeder with
Remote Process Select Not Detected
50
25.0
50
When the power source Right Display is
blank, a wire feeder with Remote Process
Select is not detected. Set the active weld
process at the power source.
MIG
PULS
Power Source Display − Wire Feeder with
Remote Process Select Detected
When the power source Right Display is
MIG, a wire feeder with Remote Process Select is detected and set for MIG operation.
The active weld process can only be
changed at the wire feeder.
Power Source Display − Wire Feeder with
Remote Process Select Detected and Set
for Pulsed MIG
When the power source Right Display is
PULS, a Remote Process Select wire feeder
is detected and is set for Pulsed MIG operation. The active weld process can only be
changed at the wire feeder.
Using a Dual Wire Feeder with Remote
Process Select
When using a dual wire feeder with Remote
Process Select, different weld programs for
the left and right side can be selected. The
power source MIG and Pulsed MIG programs for the left side of wire feeder are selected with the left side of the wire feeder active. The power source MIG and Pulsed MIG
programs for the right side are selected with
the right side of the wire feeder active. When
the right side of the wire feeder is active, the
power source Right Display will show a
decimal point in the lower right hand corner
as shown.
25.0
MIG.
Power Source Display − Dual Wire Feeder with Right Side Active and Set for MIG
Decimal point indicates wire
feeder right side is active.
50
PULS.
Decimal point indicates wire
feeder right side is active.
OM-245 171 Page 30
Power Source Display − Dual Wire Feeder with Right Side Active and Set for
Pulsed MIG
SECTION 8 − MAINTENANCE & TROUBLESHOOTING
8-1. Routine Maintenance
!
Disconnect power
before maintaining.
. Maintain more often
during severe conditions.
3 Months
Repair Or
Replace
Cracked
Cables
Replace
Damaged Or
Unreadable
Labels
Replace Cracked
Torch Body
Repair Or Replace
Cracked Cables
And Cords
Clean
And
Tighten Weld
Connections
6 Months
Blow Out Inside
8-2. Blowing Out Inside Of Unit
!
Do not remove case when
blowing out inside of unit.
To blow out unit, direct airflow
through front and back louvers as
shown.
Blowing Out Unit 2010−01
OM-245 171 Page 31
8-3. Help Displays
. All directions are in reference to the front
of the unit. All circuitry referred to is located inside the unit.
1
HELP
HELP
2
HELP
HELP
HELP
HELP
HELP
OM-245 171 Page 32
25
Help 1 Display
Indicates a malfunction in the primary power
circuit. If this display is shown, contact a Factory Authorized Service Agent.
Help 2 Display
Indicates a malfunction in the thermal protection circuitry. If this display is shown, contact
a Factory Authorized Service Agent.
3
Help 3 Display
5
Help 5 Display
6
Help 6 Display
8
Help 8 Display
Indicates the left side of the unit has overheated. The unit has shut down to allow the
fan to cool it (see Section 4-4). Operation will
continue when the unit has cooled.
Indicates the right side of the unit has overheated. The unit has shut down to allow the
fan to cool it (see Section 4-4). Operation will
continue when the unit has cooled.
Indicates operation at maximum input current. The unit has a maximum allowable input
current limit. As the line voltage decreases,
the required input current increases. If the line
voltage is too low, the output power is limited
by the input current. When this limit is
reached, the unit automatically reduces output power to continue operation. If this display
is shown, have a qualified electrician check
the input voltage.
Indicates a malfunction in the secondary
power circuit of the unit. If this display is
shown, contact a Factory Authorized Service
Agent.
Help 25 Display
Indicates machine has reached duty cycle
limits (see Section 4-4). Unit must be left on
to power the fan for cooling. Operation will
continue when unit has cooled.
8-4. Troubleshooting
Trouble
No weld output; unit completely inoperative.
Remedy
Place line disconnect switch in On position (see Section 5-9).
Check and replace line fuse(s), if necessary, or reset circuit breaker (see Section 5-9).
Check for proper input power connections (see Section 5-9).
No weld output; meter display On.
Input voltage outside acceptable range of variation (see Section 5-8).
Check, repair, or replace remote control.
Unit overheated. Allow unit to cool with fan On (see Section 4-4).
Erratic or improper weld output.
Use proper size and type of weld cable (see Section 5-5).
Clean and tighten all weld connections.
Check for correct polarity.
No 115 volts AC output at duplex receptacle or Remote 14 receptacle.
Reset supplementary protector CB1 (see Section 5-7).
No 24 volts AC output at Remote 14
receptacle.
Reset supplementary protector CB2 (see Section 5-7).
Notes
OM-245 171 Page 33
SECTION 9 − ELECTRICAL DIAGRAM
Figure 9-1. Circuit Diagram
OM-245 171 Page 34
256 237-A
OM-245 171 Page 35
OM-245 171 Page 36
Figure 10-1. Parts Assembly
74
1
3
4
75
2
76
77
78
73
5
72
12
10
79
80
11
81
9
13
71
70
8
82
14
15
70
7
16
6
69
17
68
19
67
63
64
65
66
18
62
20
21
36
23
60
59
61
22
24
58
57
56
55
53
25
54
40
38
39
26
27
28
45
41
37
29
44
43
31
47
49
48 36
46
42
36
30
53
50 51
18
52
35
34
32
33
SECTION −10 − PARTS LIST
Ref. 245 184-B
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-1. Parts Assembly
. . . 1 . . . . . . . . . . . . . . . 221 786 . .
. . . . . . . . . . . . . . . . . . . . . 175 256 . .
. . . . . . . . . . . . . . . . . . . . . 178 551 . .
. . . 2 . . . . . . . . . . . . . . . 179 310 . .
. . . 3 . . . . . . . . . . . . . . . 179 309 . .
. . . 4 . . . . . . . . . . . . . . . 195 585 . .
. . . 5 . . . . . . . . . . . . . . . 135 483 . .
. . . 6 . . . . . . . . . . . . . . . 225 097 . .
. . . 7 . . . . . . . . . . . . . . . 211 503 . .
. . . 8 . . . . . . . . . . . . . . +212 207 . .
. . . 9 . . . . . . . . . . . . . . . 196 355 . .
. . . 10 . . . . D1,D2 . . . . 201 531 . .
. . . 11 . . . . . . . . . . . . . . . 199 840 . .
. . . 12 . . . . R3/C4 . . . . 233 052 . .
. . . 13 . . . . . C8 . . . . . 219 191 . .
. . . 14 . . . . . RT1 . . . . . 199 798 . .
. . . 15 . . . . . . . . . . . . . . . 227 927 . .
. . . 16 . . . . . . L6 . . . . . . 131 447 . .
. . . 17 . . . . . . . . . . . . . . . 107 983 . .
. . . 18 . . . . . . . . . . . . . . . 179 276 . .
. . . 19 . . . . . . . . . . . . . . . 170 647 . .
. . . 20 . . . . . . L3 . . . . . . 212 150 . .
. . . 21 . . . . . . T1 . . . . . . 228 382 . .
. . . 22 . . . . . . L1 . . . . . . 212 091 . .
. . . 23 . . . . . . . . . . . . . . . 083 147 . .
. . . 24 . . . . . PC1 . . . . . 242 341 . .
. . . . . . . . . . . . . . . . . . . . . 216 113 . .
. . . . . . . . . . PLG1 . . . . 115 091 . .
. . . . . . . . . . PLG2 . . . . 201 665 . .
. . . . . . . . . . PLG3 . . . . 131 056 . .
. . . . . . . . . . PLG5 . . . . 131 204 . .
. . . . . . . . . . PLG7 . . . . 131 054 . .
. . . . . . . . . . PLG8 . . . . 131 054 . .
. . . . . . . . . . PLG9 . . . . 115 093 . .
. . . . . . . . . . PLG10 . . . . 115 094 . .
. . . . . . . . . . PLG12 . . . . 115 092 . .
. . . 25 . . . . . . . . . . . . . . . 212 072 . .
. . . 26 . . . . C12,13 . . . . 219 930 . .
. . . 27 . . . . . CB2 . . . . . 083 432 . .
. . . 28 . . . . . CB1 . . . . . 083 432 . .
. . . 29 . . . . . . . . . . . . . . +219 470 . .
. . . 30 . . . . . . . . . . . . . . . 219 335 . .
. . . 31 . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 32 . . . . . . . . . . . . . . . 217 297 . .
. . . 33 . . . . . . . . . . . . . . . 215 980 . .
. . . 34 . . . . . . . . . . . . . . . 244 628 . .
. . . 35 . . . . . . . . . . . . . . . 212 945 . .
. . . 36 . . . . L5,7,8 . . . . 241 027 . .
. . . 37 . . . . . . . . . . . . . . . 234 126 . .
Wrapper W/Insulators and Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insulator, Side Rh (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insulator, Side (Not Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Label, General Precautionary Wordless, Intl, Small . . . . . . . . . . . . . . . . .
Label, Caution Falling Equipment Can Injure−Wordles . . . . . . . . . . . . . .
Handle, Rubberized Carrying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Label, Important Remove These Two Handle Screws . . . . . . . . . . . . . . .
Heat Sink, Lh Rect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insulator, Heat Sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windtunnel, Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insulator, Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kit, Diode Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus Bar, Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resistor/Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacitor, Polyp Film .001 UF 2000V W/Terms . . . . . . . . . . . . . . . . . . . .
Thermistor, NTC 30K Ohm @ 25 Deg C 18In Lead . . . . . . . . . . . . . . . . .
Label, Warning Electric Shock/Exploding Parts−Wdles . . . . . . . . . . . . . .
Core, Toroidal 1.332 id X 1.932 od X .625 Thk . . . . . . . . . . . . . . . . . . . . .
Blank, Snap-In Nyl .500 Mtg Hole Black . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bushing, Snap-In Nyl 1.000 Id X 1.375 Mtg Hole Cent . . . . . . . . . . . . . .
Bushing, Snap-In Nyl 1.312 Id X 1.500 Mtg Hole . . . . . . . . . . . . . . . . . . .
Inductor, Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XFMR, HF Litz/Litz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inductor, Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grommet, Scr No 8/10 Panel Hole .312 Sq .500 High . . . . . . . . . . . . . . .
Circuit Card Assy, Control W/Program . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stand-Off Support, PC Card .187 Dia W/P&l .375 . . . . . . . . . . . . . . . . . .
Housing Plug+Pins (Service Kit) RC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins (Service Kit) RC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins (Service Kit) RC3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins (Service Kit) RC5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins (Service Kit) RC7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins (Service Kit) RC8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins (Service Kit) RC9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins (Service Kit) RC10 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins (Service Kit) RC12 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bracket, Mtg Capacitor/PC Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kit, Capacitor Elctlt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplementary Protector, Man Reset 1P 10A 250VAC Frict . . . . . . . . . .
Supplementary Protector, Man Reset 1P 10A 250VAC Frict . . . . . . . . . .
Panel, Rear W/Aux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Label, Warning Electric Shock Can Kill Wordless . . . . . . . . . . . . . . . . . . .
Nameplate, Rear Aux (Order by Model and Serial Number) . . . . . . . . . .
Cover, Receptacle Weatherproof Duplex Rcpt . . . . . . . . . . . . . . . . . . . . .
Bushing, Strain Relief .709/.984 Id X1.375 Mtg Hole . . . . . . . . . . . . . . . .
Cable, Power 12 Ft 8Ga 4C (Non-Stripped End) . . . . . . . . . . . . . . . . . . .
Label, Warning Incorrect Connections Wordless . . . . . . . . . . . . . . . . . . . .
Core, Toroidal .748 Id X 1.142 Od X .600 Thk . . . . . . . . . . . . . . . . . . . . . .
Nut, Conduit 1.000 Npt Knurled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
2
2
2
2
1
1
1
4
2
2
1
1
1
1
1
1
3
1
1
1
1
4
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
OM-245 171 Page 37
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-1. Parts Assembly (Continued)
. . . 38 . . . . . RC2 . . . . . 604 176 . . Rcpt, Str Dx Grd 2P3W 15A 125V *5−15R . . . . . . . . . . . . . . . . . . . . . . . .
. . . 39 . . . . . . T2 . . . . . . 251 003 . . XFMR, Control Toroidal 665 VAC Pri 1536 VA 60 Hz . . . . . . . . . . . . . . . .
. . . 40 . . . . . . . . . . . . . . . 212 947 . . Plate, Mtg Toroid XFMR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 41 . . . . . . L2 . . . . . . 218 018 . . Inductor, Pre-Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 42 . . . . . . . . . . . . . . . 218 566 . . Gasket, Inductor Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 43 . . . . . . . . . . . . . . . 219 471 . . Bracket, Mtg Filter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 44 . . . . . . . . . . . . . . . 083 147 . . Grommet, Scr No 8/10 Panel Hole .312 Sq .500 High . . . . . . . . . . . . . . .
. . . 45 . . . . . CT1 . . . . . 196 231 . . XMFR, Current Sensing 200/1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 46 . . . . . C15 . . . . . 196 143 . . Capacitor, Polyp Met Film 16. Uf 400 VAC 10% . . . . . . . . . . . . . . . . . . . .
. . . 47 . . . . . . . . . . . . . . . 219 472 . . Bracket, Mtg Capacitor Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 48 . . . . . RT2 . . . . . 199 798 . . Thermistor, NTC 30K Ohm @ 25 Deg C 18in Lead . . . . . . . . . . . . . . . . .
. . . 49 . . . . . . . . . . . . . . . 219 473 . . Bracket, Mtg CE Filter Ground Plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 50 . . . . . PC2 . . . . . 225 442 . . Circuit Card Assy, Interconnect W/Label & Clips . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 223 343 . . Clip, Wire Stdf .40−.50 Bndl .156Hole .031−.078Thk . . . . . . . . . . . . . . . .
. . . . . . . . . . PLG13 . . . . 130 203 . . Housing Plug+Pins (Service Kit) RC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . PLG14 . . . . 201 665 . . Housing Plug+Pins (Service Kit) RC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . PLG15 . . . . 115 092 . . Housing Plug+Pins (Service Kit) RC3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . PLG20 . . . . 115 093 . . Housing Plug+Pins (Service Kit) RC6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 51 . . . . . PC4 . . . . . 229 989 . . Circuit Card Assy, Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 52 . . . . . . . . . . . . . . . 153 403 . . Bushing, Snap-In Nyl .750 Id X 1.000 Mtg Hole Cent . . . . . . . . . . . . . . . .
. . . 53 . . . . . . . . . . . . . . . 217 625 . . Kit, Input/Pre-Regulator And Inverter Module (Includes) . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MOD 1, SKiip 83 HEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MOD 2, SKiip 83 EC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 54 . . . . . . . . . . . . . . . 219 335 . . Label, Warning Electric Shock Can Kill Wordless . . . . . . . . . . . . . . . . . . .
. . . 55 . . . . . RM1 . . . . . 205 751 . . Module, Power Resistor W/Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 56 . . . . . . . . . . . . . . . 229 325 . . Foot, Mtg Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 57 . . . . . . . . . . . . . . . 176 736 . . Screw, Mtg Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 58 . . . . . . . . . . . . . . . 212 073 . . Label, Warning Exploding Parts Can Wordless . . . . . . . . . . . . . . . . . . . . .
. . . 59 . . . . . . . . . . . . . . +175 132 . . Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 60 . . . . . . . . . . . . . . . 212 206 . . Windtunnel, Rh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 61 . . . . . . . . . . . . . . . 196 330 . . Heat Sink, Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 62 . . . . . . . . . . . . . . . 212 074 . . Bus Bar, Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 63 . . . . . HD1 . . . . . 182 918 . . Transducer, Current 400A Module Supply V +/− 15V . . . . . . . . . . . . . . . .
. . . 64 . . . . . PC3 . . . . . 248 799 . . Circuit Card Assy, Front Panel & Display W/Program . . . . . . . . . . . . . . .
. . . . . . . . . . PLG18 . . . . 131 204 . . Housing Plug+Pins (Service Kit) RC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . RC50 . . . . 210 233 . . Rcpt, W/Pins (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . PLG21 . . . . 212 088 . . Plug, W/Leads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . RC21 . . . . 167 640 . . Housing Plug+Pins (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 65 . . . . . . . . . . . . . . . 230 943 . . Enclosure, Connector DB−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 66 . . . . . . . . . . . . . . . 230 944 . . Cover, Enclosure Connector DB−9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 67 . . . . . . S1 . . . . . 244 920 . . Switch, Tgl 3Pst 40A 600VAC Scr Term Wide Tgl . . . . . . . . . . . . . . . . . .
. . . 68 . . . . . . . . . . . . . . . 176 226 . . Insulator, Switch Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 69 . . . . . FM1 . . . . . 196 313 . . Fan, Muffin 115V 50/60Hz 3000 RPM 6.378 Mtg Holes . . . . . . . . . . . . . .
. . . . . . . . . . PLG16 . . . . 131 054 . . Housing Plug+Pins (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . RC16 . . . . 135 635 . . Housing Plug+Pins (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 70 . . . . . . . . . . . . . . . 208 967 . . Rcpt Assy, Tw Lk Insul Fem (Dinse Type) 50/70 Series (Includes) . . . .
. . . . . . . . . . . . . . . . . . . . . 208 968 . . . . Rcpt, Tw Lk Insul W/O-Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 185 712 . . . . Insulator, Bulkhead Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 185 713 . . . . Insulator, Bulkhead Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 185 714 . . . . Washer, Tooth 22Mmid X 31.5Mmod 1.310-1Mmt Intern . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 185 717 . . . . Nut, M20-1.5 1.00Hex .19H Brs Locking . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 185 718 . . . . O-Ring, 0.989 Id X 0.070 H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 186 228 . . . . O-Ring, 0.739 Id X 0.070 H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 178 548 . . . . Terminal, Connector Friction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 71 . . . . . . . . . . . . . . . . . . . . . . . . . . Nameplate, Power (Order by Model and Serial Number) . . . . . . . . . . . . .
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
OM-245 171 Page 38
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-1. Parts Assembly (Continued)
...
...
...
...
...
...
...
...
...
...
...
72
73
74
75
76
77
78
79
80
81
82
. . . . . . . . . . . . . . . 218 041 . .
. . . . . . . . . . . . . . . 175 138 . .
..........................
. . . . . . . . . . . . . . . 174 991 . .
. . . . . . . . . . . . . . . 231 469 . .
..........................
..........................
. . . . . . . . . . . . . . . 216 112 . .
. . . . C5,6,7 . . . . 233 668 . .
. . . . . . . . . . . . . . . 235 549 . .
. . . . . . . . . . . . . . . 231 470 . .
Door, W/Quick Access Ball Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Box, Louver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Label, (Order by Model and Serial Number) . . . . . . . . . . . . . . . . . . . . . . .
Knob, Pointer 1.250 Dia X .250 Id W/Spring Clip−.21 . . . . . . . . . . . . . . .
Nut, 500−28 .69Hex .28H Brs Conical Knurl . . . . . . . . . . . . . . . . . . . . . . .
Nameplate, Connection (Order by Model and Serial Number) . . . . . . . .
Nameplate (Order by Model and Serial Number) . . . . . . . . . . . . . . . . . . .
Fastener, Panel Receptacle Quick Access . . . . . . . . . . . . . . . . . . . . . . . .
Capacitor Assy, W/Plug And Leads (Voltage Feedback) . . . . . . . . . . . . .
Panel, Front W/Knockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nut, Adapter Encoder Shaft Mtg 375−32 To 500−28 . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
2
1
1
1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
OM-245 171 Page 39
Notes
Notes
SOCKET/WRENCH SELECTION TABLE
(U.S. STANDARD)
Specifications
Socket or Wrench Size
SOCKET/WRENCH SELECTION TABLE
(METRIC)
Specifications
Socket or Wrench Size
Bolt
Diameter
Decimal
Equivalent
Bolt
Nut
Bolt
Diameter
U.S.
Decimal
Equivalent
Bolt
Nut
1/4 in.
.250 in.
3/8 in.
7/16 in.
6 mm
.2362 in.
10 mm
10 mm
5/16 in.
.3125 in.
1/2 in.
9/16 in.
8 mm
.3150 in.
14 mm
14 mm
3/8 in.
.375 in.
9/16 in.
5/8 in.
10 mm
.3937 in.
17 mm
17 mm
7/16 in.
.4375 in.
5/8 in.
3/4 in.
12 mm
.4724 in.
19 mm
19 mm
1/2 in.
.500 in.
3/4 in.
13/16 in.
14 mm
.5512 in.
22 mm
22 mm
9/16 in.
.5625 in.
7/8 in.
7/8 in.
16 mm
.6299 in.
24 mm
24 mm
5/8 in.
.625 in.
15/16 in.
1 in.
18 mm
.7087 in.
27 mm
27 mm
3/4 in.
.750 in.
1-1/8 in.
1-1/8 in.
22 mm
.8661 in.
32 mm
32 mm
7/8 in.
.875 in.
1-5/16 in.
1-5/16 in.
24 mm
.9449 in.
36 mm
36 mm
1 in.
1.000 in.
1-1/2 in.
1-1/2 in.
Notes
MATERIAL THICKNESS REFERENCE CHART
24 Gauge (.025 in.)
22 Gauge (.031 in.)
20 Gauge (.037 in.)
18 Gauge (.050 in.)
16 Gauge (.063 in.)
14 Gauge (.078 in.)
1/8 in. (.125 in.)
3/16 in. (.188 in.)
1/4 in. (.25 in.)
5/16 in. (.313 in.)
3/8 in. (.375 in.)
1/2 in. (.5 in.)
Effective January 1, 2011
(Equipment with a serial number preface of MB or newer)
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions 6. 90 Days — Parts
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to its
* Accessory (Kits)
original retail purchaser that new Miller equipment sold after the
* Canvas Covers
effective date of this limited warranty is free of defects in material
* Induction Heating Coils and Blankets, Cables, and
and workmanship at the time it is shipped by Miller. THIS
Non-Electronic Controls
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
* M-Guns
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
* MIG Guns and Subarc (SAW) Guns
WARRANTIES OF MERCHANTABILITY AND FITNESS.
* Remote Controls and RFCS-RJ45
Within the warranty periods listed below, Miller will repair or replace
* Replacement Parts (No labor)
any warranted parts or components that fail due to such defects in
* Roughneck Guns
material or workmanship. Miller must be notified in writing within
* Spoolmate Spoolguns
thirty (30) days of such defect or failure, at which time Miller will
provide instructions on the warranty claim procedures to be
followed.
Miller shall honor warranty claims on warranted equipment listed
below in the event of such a failure within the warranty time
periods. All warranty time periods start on the delivery date of the
equipment to the original end-user purchaser, and not to exceed
one year after the equipment is shipped to a North American
distributor or eighteen months after the equipment is shipped to an
International distributor.
1.
2.
3.
4.
5.
5 Years Parts — 3 Years Labor
* Original main power rectifiers only to include SCRs,
diodes, and discrete rectifier modules
3 Years — Parts and Labor
* Engine Driven Welding Generators
(NOTE: Engines are warranted separately by the
engine manufacturer.)
* Inverter Power Sources (Unless Otherwise Stated)
* Plasma Arc Cutting Power Sources
* Process Controllers
* Semi-Automatic and Automatic Wire Feeders
* Smith 30 Series Flowgauge and Flowmeter
Regulators (No Labor)
* Transformer/Rectifier Power Sources
* Water Coolant Systems (Integrated)
2 Years — Parts
* Auto-Darkening Helmet Lenses (No Labor)
1 Year — Parts and Labor Unless Specified
* Automatic Motion Devices
* CoolBelt and CoolBand Blower Unit (No Labor)
* External Monitoring Equipment and Sensors
* Field Options
(NOTE: Field options are covered for the remaining
warranty period of the product they are installed in, or
for a minimum of one year — whichever is greater.)
* Flowgauge and Flowmeter Regulators (No Labor)
* RFCS Foot Controls (Except RFCS-RJ45)
* Fume Extractors
* HF Units
* ICE Plasma Cutting Torches (No Labor)
* Induction Heating Power Sources, Coolers, and
Electronic Controls/Recorders
* Load Banks
* Motor Driven Guns (w/exception of Spoolmate
Spoolguns)
* PAPR Blower Unit (No Labor)
* Positioners and Controllers
* Racks
* Running Gear/Trailers
* Spot Welders
* Subarc Wire Drive Assemblies
* Water Coolant Systems (Non-Integrated)
* Weldcraft-Branded TIG Torches (No Labor)
* Wireless Remote Foot/Hand Controls and Receivers
* Work Stations/Weld Tables (No Labor)
6 Months — Parts
* Batteries
* Bernard Guns (No Labor)
* Tregaskiss Guns (No Labor)
Miller’s True Blue® Limited Warranty shall not apply to:
1.
2.
3.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, relays, work
station table tops and welding curtains, or parts that
fail due to normal wear. (Exception: brushes and
relays are covered on all engine-driven products.)
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable
and necessary maintenance, or equipment which has
been used for operation outside of the specifications for
the equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4) payment
of or credit for the purchase price (less reasonable depreciation
based upon actual use) upon return of the goods at customer’s risk
and expense. Miller’s option of repair or replacement will be F.O.B.,
Factory at Appleton, Wisconsin, or F.O.B. at a Miller authorized
service facility as determined by Miller. Therefore no
compensation or reimbursement for transportation costs of any
kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY
OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION, OPERATION OF LAW,
CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO
ANY AND ALL EQUIPMENT FURNISHED BY MILLER IS
EXCLUDED AND DISCLAIMED BY MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein, and
to the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available,
but may vary from province to province.
miller_warr 2011−01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
For International Locations Visit
www.MillerWelds.com
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
ORIGINAL INSTRUCTIONS − PRINTED IN USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
© 2011 Miller Electric Mfg. Co.
2011−01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising