Miller | KJ211237 | Owner Manual | Miller MILLERMATIC 185 User manual

Miller MILLERMATIC 185 User manual
OM-1313
179 084G
October 1998
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
Description
Arc Welding Power Source
And Wire Feeder
Millermatic 185
And M-15 Gun
R
Visit our website at
www.MillerWelds.com
From Miller to You
Thank you and congratulations on choosing Miller. Now
you can get the job done and get it done right. We know
you don’t have time to do it any other way.
That’s why when Niels Miller first started building arc
welders in 1929, he made sure his products offered
long-lasting value and superior quality. Like you, his
customers couldn’t afford anything less. Miller products
had to be more than the best they could be. They had to
be the best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They will
help you protect yourself against potential hazards on the worksite. We’ve
made installation and operation quick and easy.
With Miller you can count on years of reliable
service with proper maintenance. And if for
some reason the unit needs repair, there’s a
Troubleshooting section that will help you
Miller is the first welding figure out what the problem is. The parts list
equipment manufacturer in will then help you to decide which exact part
the U.S.A. to be registered
you may need to fix the problem. Warranty and
to the ISO 9001 Quality
service information for your particular model
System Standard.
are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor
to receive the latest full line catalog or
individual catalog sheets. To locate your nearest
distributor call 1-800-4-A-Miller.
Working as hard as you
do − every power source
from Miller is backed by
the most hassle-free warranty in the business.
Miller offers a Technical
Manual which provides
more detailed service and
parts information for your
unit. To obtain a Technical
Manual, contact your local
distributor. Your distributor
can also supply you with
Welding Process Manuals
such as SMAW, GTAW,
GMAW, and GMAW-P.
TABLE OF CONTENTS
The following terms are
used interchangeably
throughout this manual:
MIG = GMAW
OM1313G
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols for Installation, Operation, and Maintenance . . . . . . . . . . . . . . . . . . . . . .
1-4. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4. Installing Work Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Installing Gas Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6. Installing Welding Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7. Setting Gun Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8. Installing Wire Spool And Adjusting Hub Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-9. Changing Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-10. Electrical Service Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-11. Selecting A Location And Connecting Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-12. Threading Welding Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-13. Weld Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-14. Weld Parameter For Use With Optional Spoolmate 185 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − MAINTENANCE & TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Circuit Breakers CB1 And CB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Changing Drive Roll And Inlet Wire Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Cleaning Or Replacing Gun Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Replacing Switch And/Or Head Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. Replacing Gun Contact Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. Unicable Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − MIG WELDING (GMAW) GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Typical MIG Process Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Typical MIG Process Control Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. Holding And Positioning Welding Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4. Conditions That Affect Weld Bead Shape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-5. Gun Movement During Welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-6. Poor Weld Bead Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-7. Good Weld Bead Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-8. Troubleshooting − Excessive Spatter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-9. Troubleshooting − Porosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-10. Troubleshooting − Excessive Penetration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-11. Troubleshooting − Lack Of Penetration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-12. Troubleshooting − Incomplete Fusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-13. Troubleshooting − Burn-Through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-14. Troubleshooting − Waviness Of Bead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-15. Troubleshooting − Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-16. Common MIG Shielding Gases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONS AND ACCESSORIES
WARRANTY
1
1
1
3
3
4
5
5
5
6
7
7
8
8
9
9
10
10
11
12
13
14
14
15
15
15
15
16
17
18
18
18
19
20
20
21
22
23
24
24
24
25
25
26
26
26
27
27
27
28
30
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som _nd_5/97
1-1. Symbol Usage
Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.
Y Marks a special safety message.
. Means “Note”; not safety related.
This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.
1-2. Arc Welding Hazards
Y The symbols shown below are used throughout this manual to
call attention to and identify possible hazards. When you see
the symbol, watch out, and follow the related instructions to
avoid the hazard. The safety information given below is only
a summary of the more complete safety information found in
the Safety Standards listed in Section 1-4. Read and follow all
Safety Standards.
D If earth grounding of the workpiece is required, ground it directly
with a separate cable − do not use work clamp or work cable.
Y Only qualified persons should install, operate, maintain, and
repair this unit.
D Wear a safety harness if working above floor level.
D Keep all panels and covers securely in place.
Y During operation, keep everybody, especially children, away.
D Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic wire welding, the
wire, wire reel, drive roll housing, and all metal parts touching the
welding wire are electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
D Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
D Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
D Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
D Do not connect more than one electrode or work cable to any
single weld output terminal.
SIGNIFICANT DC VOLTAGE exists after removal of
input power on inverters.
D Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
D Do not touch live electrical parts.
D Wear dry, hole-free insulating gloves and body protection.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
D Use AC output ONLY if required for the welding process.
D If AC output is required, use remote output control if present on
unit.
D Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
D Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
D Keep your head out of the fumes. Do not breathe the fumes.
D Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
D When making input connections, attach proper grounding conductor first − double-check connections.
D Frequently inspect input power cord for damage or bare wiring −
replace cord immediately if damaged − bare wiring can kill.
D Turn off all equipment when not in use.
D Do not use worn, damaged, undersized, or poorly spliced cables.
D Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
D Do not drape cables over your body.
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D If inside, ventilate the area and/or use exhaust at the arc to remove
welding fumes and gases.
D If ventilation is poor, use an approved air-supplied respirator.
D Read the Material Safety Data Sheets (MSDSs) and the
manufacturer’s instructions for metals, consumables, coatings,
cleaners, and degreasers.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and if necessary, while wearing an
air-supplied respirator. The coatings and any metals containing
these elements can give off toxic fumes if welded.
OM-1313 Page 1
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear a welding helmet fitted with a proper shade of filter to protect
your face and eyes when welding or watching (see ANSI Z49.1
and Z87.1 listed in Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash and
glare; warn others not to watch the arc.
D Wear protective clothing made from durable, flame-resistant material (leather and wool) and foot protection.
BUILDUP OF GAS can injure or kill.
D Shut off shielding gas supply when not in use.
D Always ventilate confined spaces or use
approved air-supplied respirator.
HOT PARTS can cause severe burns.
D Do not touch hot parts bare handed.
D Allow cooling period before working on gun or
torch.
MAGNETIC FIELDS can affect pacemakers.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
D Protect yourself and others from flying sparks and hot metal.
D Do not weld where flying sparks can strike flammable material.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock and fire hazards.
D Do not use welder to thaw frozen pipes.
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
D Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
FLYING METAL can injure eyes.
D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
D Wear approved safety glasses with side
shields even under your welding helmet.
OM-1313 Page 2
D Pacemaker wearers keep away.
D Wearers should consult their doctor before
going near arc welding, gouging, or spot
welding operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Wear approved ear protection if noise level is
high.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D Protect compressed gas cylinders from excessive heat, mechanical shocks, slag, open flames, sparks, and arcs.
D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Keep cylinders away from any welding or other electrical circuits.
D Never drape a welding torch over a gas cylinder.
D Never allow a welding electrode to touch any cylinder.
D Never weld on a pressurized cylinder − explosion will result.
D Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and
associated parts in good condition.
D Turn face away from valve outlet when opening cylinder valve.
D Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D Read and follow instructions on compressed gas cylinders,
associated equipment, and CGA publication P-1 listed in Safety
Standards.
1-3. Additional Symbols for Installation, Operation, and Maintenance
FIRE OR EXPLOSION hazard.
MOVING PARTS can cause injury.
D Do not install or place unit on, over, or near
combustible surfaces.
D Do not install unit near flammables.
D Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
FALLING UNIT can cause injury.
H.F. RADIATION can cause interference.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are
long enough to extend beyond opposite side of
unit.
D
OVERUSE can cause OVERHEATING
D
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
D
D
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
STATIC (ESD) can damage PC boards.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
ARC WELDING can cause interference.
MOVING PARTS can cause injury.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
D
D
WELDING WIRE can cause injury.
D Do not press gun trigger until instructed to do
so.
D Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
D
D
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
1-4. Principal Safety Standards
Safety in Welding and Cutting, ANSI Standard Z49.1, from American
Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
Safety and Health Standards, OSHA 29 CFR 1910, from Superintendent of Documents, U.S. Government Printing Office, Washington, D.C.
20402.
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers That Have Held Hazardous Substances, American
Welding Society Standard AWS F4.1, from American Welding Society,
550 N.W. LeJeune Rd, Miami, FL 33126
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1235 Jefferson Davis Highway,
Suite 501, Arlington, VA 22202.
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale
Boulevard, Rexdale, Ontario, Canada M9W 1R3.
Safe Practices For Occupation And Educational Eye And Face
Protection, ANSI Standard Z87.1, from American National Standards
Institute, 1430 Broadway, New York, NY 10018.
Cutting And Welding Processes, NFPA Standard 51B, from National
Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
OM-1313 Page 3
1-5. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
To reduce magnetic fields in the workplace, use the following
procedures:
OM-1313 Page 4
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from operator as practical.
5. Connect work clamp to workpiece as close to the weld as possible.
About Pacemakers:
Pacemaker wearers consult your doctor first. If cleared by your doctor,
then following the above procedures is recommended.
SECTION 2 − INSTALLATION
2-1. Specifications
Rated Welding
Output
Amperage
Range
Maximum
Open-Circuit
Voltage DC
Amperes Input at
Rated Load
Output, 60 Hz,
Single-Phase
200 V
230 V
Weight
KVA
Overall
Dimensions
KW
Length: 36 in
(915 mm)
150 A @ 23 Volts
DC, 60% Duty Cycle
30 − 185
33
30 (1.6)*
26 (1.4)*
6 (0.27)*
5 (0.13)*
165 lb
(75 kg)
Width: 18 in
(457 mm)
Height: 27 in
(686 mm)
Wire Type And Diameter
Solid Steel /
Stainless Steel
Flux Cored
Aluminum
.023 − .035 in
(0.6 - 0.9 mm)
.030 − .045 in
(0.8 − 1.2 mm)
.030 − .035 in
(0.8 − 0.9 mm)
Calculated Wire Speed
Range At No Load
Max Wire Feed Speed
While Welding
138 − 795 IPM (3.5 − 20.3 m/min)
650 IPM (16.5 m/min)
*While idling
2-2. Volt-Ampere Curves
Volt-ampere curves show minimum and maximum voltage and
amperage output capabilities of
unit. Curves of other settings fall between curves shown.
va_curve1 4/95 − SB-180 824
OM-1313 Page 5
2-3. Duty Cycle And Overheating
Duty Cycle is percentage of 10 minutes that unit can weld at rated load
without overheating.
If unit overheats, thermostat(s)
opens, output stops, and cooling
fan runs. Wait fifteen minutes for
unit to cool. Reduce amperage or
voltage, or duty cycle before
welding.
Y Exceeding duty cycle can
damage unit and void
warranty.
60% Duty Cycle At 150 Amperes
6 Minutes Welding
4 Minutes Resting
Overheating
A or V
0
15
OR
Reduce Duty Cycle
Minutes
duty1 4/95 − SB-181 009
OM-1313 Page 6
2-4. Installing Work Clamp
1
2
Slide boot onto work cable. Route
cable out front panel opening from
inside.
4
3
Negative (−) Output Terminal
Connect cable to terminal and
cover connection with boot.
5
2
Work Cable
Boot
4
5
Hardware
Work Clamp
Route cable through clamp handle
and secure as shown.
1
Close door.
Tools Needed:
3
1/2, 3/4 in
ST-801 566
2-5. Installing Gas Supply
Obtain gas cylinder and chain to
running gear, wall, or other stationary support so cylinder cannot fall
and break off valve.
1
Tools Needed:
2
1
Cap
2
Cylinder Valve
Remove cap, stand to side of valve,
and open valve slightly. Gas flow
blows dust and dirt from valve.
Close valve.
5/8, 1-1/8 in
3
Argon Gas
OR
1
4
Regulator/Flowmeter
5
Regulator/Flowmeter Gas
Hose Connection
6
Welding Power Source Gas
Hose Connection
Connect customer supplied gas
hose between regulator/flowmeter
gas hose connection, and fitting on
rear of welding power source.
7
7
2
3
8
6
Cylinder
Install so face is vertical.
4
5
3
9
CO2 Gas
Flow Adjust
Typical flow rate is 20 cfh (cubic feet
per hour). Check wire manufacturer’s recommended flow rate.
8
CO2 Adapter (Customer Supplied)
9
O-Ring (Customer Supplied)
Install adapter with O-ring between
regulator/flowmeter and
CO2
cylinder.
ST-801 571 / ST-802 028
OM-1313 Page 7
2-6. Installing Welding Gun
1
2
3
Drive Assembly
Gun Securing Knob
Gun End
Loosen securing knob. Insert gun
end through opening until it bottoms
against drive assembly. Tighten
nut.
1
4
Gun Trigger Plug
Insert plug into receptacle, and
tighten threaded collar.
2
3
Close door.
4
Ref. ST-801 567
2-7. Setting Gun Polarity
1
Polarity Changeover Label
(Located on inside of side
door panel)
Always read and follow manufacture’s recommended polarity.
Wire Drive Assembly Lead
To Positive (+) Output Terminal
Work Clamp Lead To
Negative (−) Output Terminal
GUN POLARITY
CHANGEOVER CONNECTIONS
Reverse Lead Connections − For Electrode
Negative (DCEN) For Flux Cored Wires
(FCAW Process). Drive Assembly
Becomes Negative
S-144 449-D
Tools Needed:
3/4, 11/16 in
OM-1313 Page 8
1
2-8. Installing Wire Spool And Adjusting Hub Tension
Use compression spring with
8 in (200 mm) spools.
Tools Needed:
15/16 in
When a slight force is needed
to turn spool, tension is set.
ST-072573-B
2-9. Changing Input Voltage
Y Turn Off unit, and disconnect
input power.
Unit was shipped from factory set
for 230 volts.
1
2
3
2
Transformer T1
Rear Of Power Switch S1
Lead Marked 230 Volt And
Fan Motor Lead
Disconnect 230 volt lead and fan
motor lead from rear of S1. Leave
fan motor lead connected to 230
volt lead.
3
4
Lead Marked 200 Volt
Remove cable tie, and slide short
piece of sleeving off 200 volt lead,
and slide sleeving over end of 230
volt and fan motor leads. Fold
sleeving over and secure in place.
1
Connect 200 volt lead to S1 where
230 volt lead was removed.
Reinstall wrapper.
4
Tools Needed:
3/8, 7/16 in
ST-801 580-A
OM-1313 Page 9
2-10. Electrical Service Guide
Input Voltage
200
230
Input Amperes At Rated Output
30
26
Max Recommended Standard Fuse Or Circuit Breaker Rating In
Amperes
45
40
Min Input Conductor Size In AWG/Kcmil
10
10
97 (29)
128 (39)
10
10
Max Recommended Input Conductor Length In Feet (Meters)
Min Grounding Conductor Size In AWG/Kcmil
Reference: 1996 National Electrical Code (NEC).
S-0092-J
2-11. Selecting A Location And Connecting Input Power
1
Rating Label
Supply correct input power.
2
3
18 in (457 mm) of
space for airflow
Y Do not move or operate unit
where it could tip.
Plug
Receptacle
Connect plug to receptacle.
4
Input And Grounding
Conductors
Connect directly to line disconnect
device if hard wiring is required.
5
Line Disconnect Device
See Section 2-10.
Y Special installation may be
required where gasoline or
volatile liquids are present −
see NEC Article 511 or CEC
Section 20.
Y Always connect grounding
conductor first.
= GND/PE
5
L1
L2
1
2
1
4
3
L1
L2
230 VAC, 1
ST-801 568
OM-1313 Page 10
2-12. Threading Welding Wire
Tools Needed:
4 in
(102 mm)
6 in
(150 mm)
Open pressure assembly.
Pull and hold wire; cut off end.
Push wire thru guides into gun;
continue to hold wire.
Tighten
Close and tighten pressure
assembly, and let go of wire.
Remove gun nozzle and contact tip.
Turn On.
WOOD
Press gun trigger until wire
comes out of gun. Reinstall
contact tip and nozzle.
Feed wire to check drive roll pressure.
Tighten knob enough to prevent slipping.
Cut off wire. Close
and latch door.
Ref. ST-801 570 / ST-801 083 / S-0627-A
OM-1313 Page 11
2-13. Weld Parameter
Material Thickness
Wire Type,
Shielding Gas,
And Flow Rate
Wire
Diameter
(inch)
Operator
Controls
3/8 in
(9.5
mm)
1/4 in
(6.4
mm)
3/16 in
(4.8
mm)
1/8 in
(3.2
mm)
12 ga
14 ga
16 ga
18 ga
20 ga
22 ga
Voltage Tap
−−
6
5
4
3
3
2
2
1
1
Wire Speed
−−
100
80
65
55
45
35
25
15
5
Voltage Tap
6
5
4
3
3
2
2
1
1
−−
Wire Speed
80
70
60
55
45
35
25
15
5
−−
Voltage Tap
6
5
4
3
3
2
2
2
−−
−−
Wire Speed
70
60
50
45
40
30
20
10
−−
−−
Voltage Tap
−−
5
4
3
3
2
2
1
1
1
Wire Speed
−−
90
80
70
60
50
40
35
25
12
Voltage Tap
6
5
4
3
3
2
2
1
1
1
Wire Speed
85
75
65
55
50
45
35
20
5
0
Voltage Tap
6
5
4
3
3
2
2
1
1
−−
Wire Speed
80
70
60
45
40
30
20
10
0
−−
Voltage Tap
6
5
5
4
4
3
2
1
−−
−−
Wire Speed
80
70
65
55
50
30
20
10
−−
−−
Voltage Tap
6
5
4
3
3
2
1
−−
−−
−−
Wire Speed
60
50
40
30
25
20
10
−−
−−
−−
Voltage Tap
5
4
4
4
3
3
3
2
2
2
Wire Speed
95
85
80
60
50
50
50
30
20
20
Voltage Tap
5
5
4
3
3
2
2
2
1
−−
Wire Speed
70
70
70
50
45
50
45
40
0
−−
Voltage Tap
6
5
5
4
3
2
2
2
−−
−−
Wire Speed
65
40
40
30
30
25
20
10
−−
−−
.023
E70S-6
CO2
20 cfh+
.030
.035
.023
E70S-6
75% Argon
25% CO2
20 cfh+
.030
.035
.030
E71T-GS
Flux Core
.035
.023
ER 308
Stainless Steel
90% HE /
7.5% Argon /
2.5% CO2
20 cfh+
.030
.035
*Do not change Voltage switch position while welding. Wire Speed is a starting value only, and can be adjusted while welding. Weld conditions also
depend on other variables such as stickout, travel speed, weld angle, cleanliness of metal, etc.
OM-1313 Page 12
2-14. Aluminum Weld Parameter For Use With Optional Spoolmate 185
Wire Type,
Shielding Gas,
And Flow Rate
Wire
Diameter
(inch)
Material Thickness
Operator
Controls
3/8 in (9.5 mm)
1/4 in (6.4 mm)
3/16 in
(4.8 m m)
1/8 in (3.2 mm)
14 ga
Voltage Tap
5
5
4
3
2
Wire Speed
88
88
73
55
45
Voltage Tap
6
6
5
4
2
Wire Speed
95
85
68
59
34
Voltage Tap
−
5
4
3
2
Wire Speed
−
100
90
80
70
Voltage Tap
6
6
5
4
2
Wire Speed
100
92
85
70
60
.030
4043 AL
100% Argon
.035
.030
5356 AL
100% Argon
.035
OM-1313 Page 13
SECTION 3 − OPERATION
3-1. Front Panel Controls
Controls For Standard Units
1
Wire Speed Control
Use control to select a wire feed
speed. Scale around control is not
actual wire feed speed, but is for
reference only.
2
Voltage Switch
The higher the selected number,
the thicker the material that can be
welded (see Section 2-13). Do not
switch under load.
3
4
Pilot Light
Power Switch
1
2
3
4
Ref. ST-180 930
OM-1313 Page 14
SECTION 4 − MAINTENANCE & TROUBLESHOOTING
4-1. Routine Maintenance
. Maintain more often
Y Disconnect power
before maintaining.
during severe conditions.
3 Months
Clean And
Tighten
Weld
Terminals
Repair Or
Replace
Cracked
Cables And
Cords
Replace
Damaged Or
Unreadable
Labels
6 Months
Remove drive roll
and apply light coat
of oil or grease to
drive motor shaft.
Blow Out Or
Vacuum Inside
4-2. Circuit Breakers CB1 And CB2
1
2
Y Turn Off unit.
1
Circuit Breaker CB1
CB1 protects the transformer from
overload. If CB1 opens, wire
feeding stops.
2
Circuit Breaker CB2
CB2 protects the trigger circuit from
overload. If CB1 opens, weld output
stops.
Press button to reset
breaker. Close door.
circuit
Ref. ST-801 567
4-3. Changing Drive Roll And Inlet Wire Guide
1
Drive Roll
Choose correct drive roll for wire
type, and install as shown.
2
Inlet Wire Guide
Remove guide by pressing on
barbed area, or cutting off one end
near housing and pulling it out of
hole. Push new guide into hole from
rear until it snaps in place.
1
Tools Needed:
2
Ref. ST-801 569
OM-1313 Page 15
4-4. Cleaning Or Replacing Gun Liner
Tools Needed:
Y Disconnect gun first.
3/8 in
Head tube
Remove nozzle, contact tip,
adapter, and wire outlet guide.
3/8 in
Wire Outlet Guide
Remove liner.
Lay gun cable out straight
before installing new liner.
To Reassemble Gun:
Insert new liner.
Install and tighten wire outlet guide.
Blow out gun casing.
Cut liner off 3/4 in (20 mm) (3/8 in
[9.5 mm] for aluminum) from head
tube.
Install adapter, contact tip, and
nozzle.
Ref. ST-800 797-A
OM-1313 Page 16
4-5. Replacing Switch And/Or Head Tube
Y Disconnect gun first.
3
1
4
2
Remove handle
locking nut.
Secure head
tube in vice.
5
Remove shock washers from front and
rear of head tube.
6
Slide handle.
Remove switch housing. Note: If installing new
switch, push switch lead connectors onto terminal of
new switch (polarity is not important). Install switch
back into handle, and secure with handle locking nut.
If replacing head tube, continue to end of figure.
Loosen jam nut. Remove
from vice and turn head
tube out by hand.
Do not disturb cable connection between
cable connector and connector nut.
7
Install both existing shock washers
to new head tube and hand-tighten
head tube into connector cable.
9
8
Place head tube in vice and tighten
to within 1/8 in (3.2 mm) spacing between connector cable and body.
Remove from vice. Reposition
handle and install switch housing.
Secure with handle locking nut.
Tools Needed:
3/4 in
Ref. ST-800 795-A
OM-1313 Page 17
4-6. Replacing Gun Contact Tip
Y Turn Off unit.
1
2
Nozzle
Contact Tip
Cut off welding wire at contact tip.
Remove nozzle.
Tools Needed:
Remove contact tip and install new
contact tip. Reinstall nozzle.
2
1
ST-149 326-B
4-7. Unicable Repair
To repair or replace unicable, order Unicable Clamp Kit, part number 172 018.
4-8. Troubleshooting
Welding Trouble
No weld output; wire does not feed.
Remedy
Secure power cord plug in receptacle (see Section 2-11).
Check and replace power switch if necessary.
Check circuit breakers CB1 and/or CB2, and reset if necessary (see Section 4-2).
Replace building line fuse or reset circuit breaker if open (see Section 2-11).
Secure gun plug in receptacle or repair leads, or replace trigger switch (see Section 2-6 and/or 4-5).
Thermostat TP1 open (overheating). Allow fan to run; the thermostat will close when the unit has cooled
(see Section 2-3).
No weld output; wire feeds.
Connect work clamp to get good metal to metal contact.
Replace contact tip (see Section 4-6).
Low weld output.
Connect unit to proper input voltage or check for low line voltage (see Section 2-11).
Low, high, or erratic wire speed.
Readjust front panel settings (see Section 3-1).
Change to correct size drive roll (see Section 4-3).
Readjust drive roll pressure (see Section 2-12).
Replace inlet guide, contact tip, and/or liner if necessary (see Sections 2-12, and 4-4).
Wire Drive/Gun Trouble
Remedy
Electrode wire feeding stops during Straighten gun cable and/or replace damaged parts (see Section 4-4).
welding.
Adjust drive roll pressure (see Section 2-12).
Readjust hub tension (see Section 2-8).
Replace contact tip if blocked (see Section 4-6).
Clean or replace wire inlet guide or liner if dirty or plugged (see Section 4-4).
Replace drive roll if worn or slipping (see Section 4-3).
Secure gun plug in receptacle or repair leads, or replace trigger switch (see Section 2-6 and/or 4-5).
Check and clear any restrictions at drive assembly and liner (see Section 4-4).
Have nearest Factory Authorized Service Agent check drive motor.
OM-1313 Page 18
SECTION 5 − ELECTRICAL DIAGRAM
SB-186 065
Figure 5-1. Circuit Diagram
OM-1314 Page 19
SECTION 6 − MIG WELDING (GMAW) GUIDELINES
6-1. Typical MIG Process Connections
Y Weld current can damage
electronic parts in vehicles.
Disconnect both battery
cables before welding on a
vehicle. Place work clamp as
close to the weld as possible.
Regulator/
Flowmeter
Wire Feeder/
Power Source
Gun
Shielding Gas
Gas
Workpiece
Work Clamp
light mig 5/967 / ST-801 909
OM-1313 Page 20
6-2.
Typical MIG Process Control Settings
NOTE
These settings are guidelines only. Material and wire type, joint design, fitup,
position, shielding gas, etc. affect settings. Test welds to be sure they comply to
specifications.
Material thickness determines weld
parameters.
1/8 or
.125 in
Convert Material
Thickness to
Amperage (A)
(.001 in = 1 ampere)
.125 in = 125 A
.035 in
Wire Size
Amperage Range
.023 in
30 − 90 A
.030 in
.035 in
40 − 145 A
50 − 180 A
Select Wire Size
Wire
Size
Recommendation
Wire Speed
(Approx.)
Select Wire Speed
(Amperage)
.023 in
.030 in
.035 in
3.5 in per ampere
2 in per ampere
1.6 in per ampere
3.5 x 125 A = 437 ipm
2 x 125 A = 250 ipm
1.6 x 125 A = 200 ipm
125 A based on 1/8 in
material thickness
ipm = inch per minute
Low voltage: wire stubs into work
High voltage: arc is unstable (spatter)
Select Voltage
Set voltage midway between high/low voltage.
Wire speed (amperage) controls weld penetration (wire speed = burn-off rate)
Voltage controls height and width of
weld bead.
Ref. ST-801 865
OM-1313 Page 21
6-3.
Holding And Positioning Welding Gun
NOTE
Welding wire is energized when gun trigger is pressed. Before lowering helmet and
pressing trigger, be sure wire is no more than 1/2 in (13 mm) past end of nozzle,
and tip of wire is positioned correctly on seam.
1
1
3
2
2
3
4
5
Hold Gun and Control Gun
Trigger
Workpiece
Work Clamp
Electrode Extension (Stickout)
1/4 to 1/2 in (6 To 13 mm)
Cradle Gun and Rest Hand on
Workpiece
5
4
0°-15°
90°
90°
End View Of Work Angle
Side View Of Gun Angle
GROOVE WELDS
0°-15°
45°
45°
End View Of Work Angle
Side View Of Gun Angle
FILLET WELDS
OM-1313 Page 22
S-0421-A
6-4.
Conditions That Affect Weld Bead Shape
NOTE
Weld bead shape depends on gun angle, direction of travel, electrode extension
(stickout), travel speed, thickness of base metal, wire feed speed (weld current),
and voltage.
10°
Push
Perpendicular
10°
Drag
GUN ANGLES AND WELD BEAD PROFILES
Short
Normal
Long
ELECTRODE EXTENSIONS (STICKOUT)
Short
Normal
Long
FILLET WELD ELECTRODE EXTENSIONS (STICKOUT)
Slow
Normal
GUN TRAVEL SPEED
Fast
S-0634
OM-1313 Page 23
6-5.
Gun Movement During Welding
NOTE
Normally, a single stringer bead is satisfactory for most narrow groove weld joints;
however, for wide groove weld joints or bridging across gaps, a weave bead or
multiple stringer beads works better.
1
1
2
2
3
Stringer Bead − Steady
Movement Along Seam
Weave Bead − Side To Side
Movement Along Seam
Weave Patterns
Use weave patterns to cover a wide
area in one pass of the electrode.
3
S-0054-A
6-6.
Poor Weld Bead Characteristics
1
2
3
1
2
3
4
5
Large Spatter Deposits
Rough, Uneven Bead
Slight Crater During Welding
Bad Overlap
Poor Penetration
4
5
S-0053-A
6-7.
Good Weld Bead Characteristics
1
2
3
1
Fine Spatter
Uniform Bead
Moderate Crater During
Welding
Weld a new bead or layer for each
1/8 in (3.2 mm) thickness in metals
being welded.
4
5
2
3
4
No Overlap
Good Penetration into Base
Metal
5
S-0052-B
OM-1313 Page 24
6-8.
Troubleshooting − Excessive Spatter
Excessive Spatter − scattering of molten metal particles that
cool to solid form near weld bead.
S-0636
Possible Causes
Corrective Actions
Wire feed speed too high.
Select lower wire feed speed.
Voltage too high.
Select lower voltage range.
Electrode extension (stickout) too long.
Use shorter electrode extension (stickout).
Workpiece dirty.
Remove all grease, oil, moisture, rust, paint, undercoating, and dirt from work surface before welding.
Insufficient shielding gas at welding arc.
Increase flow of shielding gas at regulator/flowmeter and/or prevent drafts near welding arc.
Dirty welding wire.
Use clean, dry welding wire.
Eliminate pickup of oil or lubricant on welding wire from feeder or liner.
6-9.
Troubleshooting − Porosity
Porosity − small cavities or holes resulting from gas pockets
in weld metal.
S-0635
Possible Causes
Insufficient shielding gas at welding arc.
Corrective Actions
Increase flow of shielding gas at regulator/flowmeter and/or prevent drafts near welding arc.
Remove spatter from gun nozzle.
Check gas hoses for leaks.
Place nozzle 1/4 to 1/2 in (6-13 mm) from workpiece.
Hold gun near bead at end of weld until molten metal solidifies.
Wrong gas.
Use welding grade shielding gas; change to different gas.
Dirty welding wire.
Use clean, dry welding wire.
Eliminate pick up of oil or lubricant on welding wire from feeder or liner.
Workpiece dirty.
Remove all grease, oil, moisture, rust, paint, coatings, and dirt from work surface before welding.
Use a more highly deoxidizing welding wire (contact supplier).
Welding wire extends too far out of nozzle.
Be sure welding wire extends not more than 1/2 in (13 mm) beyond nozzle.
6-10. Troubleshooting − Excessive Penetration
Excessive Penetration − weld metal melting through base metal
and hanging underneath weld.
Excessive Penetration Good Penetration
S-0639
Possible Causes
Excessive heat input.
Corrective Actions
Select lower voltage range and reduce wire feed speed.
Increase travel speed.
OM-1313 Page 25
6-11. Troubleshooting − Lack Of Penetration
Lack Of Penetration − shallow
fusion between weld metal and
base metal.
Lack of Penetration
Good Penetration
S-0638
Possible Causes
Corrective Actions
Improper joint preparation.
Material too thick. Joint preparation and design must provide access to bottom of groove while
maintaining proper welding wire extension and arc characteristics.
Improper weld technique.
Maintain normal gun angle of 0 to 15 degrees to achieve maximum penetration.
Keep arc on leading edge of weld puddle.
Be sure welding wire extends not more than 1/2 in (13 mm) beyond nozzle.
Insufficient heat input.
Select higher wire feed speed and/or select higher voltage range.
Reduce travel speed.
6-12. Troubleshooting − Incomplete Fusion
Incomplete Fusion − failure of weld metal to fuse completely with
base metal or a preceeding weld bead.
S-0637
Possible Causes
Corrective Actions
Workpiece dirty.
Remove all grease, oil, moisture, rust, paint, undercoating, and dirt from work surface before
welding.
Insufficient heat input.
Select higher voltage range and/or adjust wire feed speed.
Improper welding technique.
Place stringer bead in proper location(s) at joint during welding.
Adjust work angle or widen groove to access bottom during welding.
Momentarily hold arc on groove side walls when using weaving technique.
Keep arc on leading edge of weld puddle.
Use correct gun angle of 0 to 15 degrees.
6-13. Troubleshooting − Burn-Through
Burn-Through − weld metal melting completely through base metal
resulting in holes where no metal remains.
S-0640
Possible Causes
Excessive heat input.
Corrective Actions
Select lower voltage range and reduce wire feed speed.
Increase and/or maintain steady travel speed.
OM-1313 Page 26
6-14. Troubleshooting − Waviness Of Bead
Waviness Of Bead − weld metal that is not parallel and does not cover
joint formed by base metal.
S-0641
Possible Causes
Corrective Actions
Welding wire extends too far out of nozzle.
Be sure welding wire extends not more than 1/2 in (13 mm) beyond nozzle.
Unsteady hand.
Support hand on solid surface or use two hands.
6-15. Troubleshooting − Distortion
Distortion − contraction of weld metal during welding that forces
base metal to move.
Base metal moves
in the direction of
the weld bead.
S-0642
Possible Causes
Excessive heat input.
Corrective Actions
Use restraint (clamp) to hold base metal in position.
Make tack welds along joint before starting welding operation.
Select lower voltage range and/or reduce wire feed speed.
Increase travel speed.
Weld in small segments and allow cooling between welds.
OM-1313 Page 27
6-16. Common MIG Shielding Gases
This is a general chart for common gases and where they are used. Many different combinations (mixtures) of
shielding gases have been developed over the years. The most commonly used shielding gases are listed in the
following table.
Application
Gas
Spray Arc Steel
Short Circuiting Steel
Short Circuiting
Stainless Steel
Argon
All Positions
Argon + 25% CO2
Flat & Horizontal1 Fillet
All Positions
CO2
Flat & Horizontal1 Fillet
All Positions
Tri-Mix3
1
Globular Transfer
2
Single Pass Welding Only
3
90% HE + 7-1/2% AR + 2-1/2% CO2
OM-1313 Page 28
Short Circuiting
Aluminum
All Positions2
All Positions
Notes
OM-1313 Page 29
13
11
12
SECTION 7 − PARTS LIST
. Hardware is common and
20
19
17
16
7
8
9
15
10
18
14
not available unless listed.
5
21
6
NEG
22
27
29
33
34
9
36
Fig 7-3
1
35
2
30
32
28
31
3
26
25
24
23
4
Fig 7-2
POS
ST-801 572
Figure 7-1. Main Assembly
OM-1313 Page 30
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 7-1. Main Assembly
. . . 1 . . . . . . . . . . . . . 089 899 . . LATCH, slide flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 2 . . . . . . . . . . . . . 134 464 . . LABEL, warning general precautionary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 3 . . . . . . . . . . . . +151 565 . . WRAPPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . . . . . . . . . Fig 7-2 . . CENTER BAFFLE, w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 5 . . . . SR1 . . . 191 487 . . RECTIFIER ASSEMBLY, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . 180 920 . . . . BRACKET RECTIFIER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . 191 375 . . . . RECTIFIER SI DIODE ASSEMBLYY, POS . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . 191 376 . . . . RECTIFIER SI DIODE ASSEMBLYY, NEG . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . 152 862 . . . . GROMMET, SCR .250 panel hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
. . . . . . . . . . . . . . . . . . . 026 947 . . . . STAND-OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . TP1 . . . 604 515 . . . . THERMOSTAT, NC open 211F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 6 . . . . . FM . . . . 123 468 . . . . MOTOR, fan 230V 60/50 Hz 3000RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 7 . . . . . . . . . . . . . 005 656 . . . . BLADE, fan 6.000 4wg 30 deg .175 bore . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 8 . . . . . . . . . . . . . 180 918 . . PANEL, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 9 . . . . . . . . . . . . . 190 773 . . BEZEL, front rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 10 . . . . . . . . . . . . . 180 923 . . BRACKET, bottle retainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 11 . . . . . . . . . . . . . 602 387 . . CHAIN, weldless 2/0 x 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 12 . . . . . . . . . . . . . 605 227 . . NUT, 750-14 knurled 1.68dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 13 . . . . PLG1 . . . 181 072 . . CORD SET, 250V 6-50P 12ga 3/c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 14 . . . . . . . . . . . . . . 111 443 . . BUSHING, strain relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 15 . . . . GS1 . . . 125 785 . . VALVE, 24VAC 2 way . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 16 . . . . . . . . . . . . . 180 916 . . BASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 17 . . . . . . . . . . . . . 147 893 . . AXLE, running gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 18 . . . . . . . . . . . . . 186 758 . . WHEEL, rubolene 10in dia x 2.25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 19 . . . . . . . . . . . . . 602 250 . . WASHER, flat .812 ID x 1.469 OD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 20 . . . . . . . . . . . . . 121 614 . . RING, rtng ext .750 shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 21 . . . . . . Z . . . . . 180 989 . . STABILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . TP2 . . . 163 266 . . THERMOSTAT, NC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 22 . . . . . . . . . . . . . 008 999 . . CASTER, swvl 4.00 in plastic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 23 . . . . . T1 . . . . 180 925 . . TRANSFORMER, power main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 24 . . . . . . . . . . . . . 180 924 . . PANEL, side lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 25 . . . . . S2 . . . . 153 197 . . SWITCH, selector 6 position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 26 . . . . RC2 . . . 048 282 . . RECEPTACLE W/SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 27 . . . . . S1 . . . . . 124 511 . . SWITCH, tgl DPST 40A 600VAC scr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 28 . . . . . . . . . . . . . 180 917 . . PANEL, front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 29 . . . . . . . . . . . . . 148 956 . . HANDLE, switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 30 . . . . . . . . . . . . . 097 924 . . KNOB, pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 31 . . . . . R1 . . . . 035 897 . . POTENTIOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 32 . . . . . . . . . . . . . . . . . . . . . . . . NAMEPLATE, (order by model and serial number) . . . . . . . . . . . . . . . . . . . 1
. . . 33 . . . . . . . . . . . . . 147 571 . . HANDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 34 . . . . . . . . . . . . . 130 750 . . CLAMP, work 300A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 35 . . . . . . . . . . . . . 600 318 . . CABLE, weld copper (order by ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10ft
. . . 36 . . . . . . . . . . . . . . Fig 7-3 . . M-15 GUN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . 165 745 . . HOUSING & PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . 173 374 . . REGULATOR/FLOWMETER, dual scale . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . 183 581 . . HOSE, gas 5ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1313 Page 31
. Hardware is common and
not available unless listed.
1
2
3
4
5
6
10
7
9
8
15
11
12
14
13
Fig.7−4 − 28
16
17
18
27
20
23
26
25
24
22
21
ST-801 631-D
Figure 7-2. Center Baffle w/Components
OM-1313 Page 32
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 7-2. Baffle, Center w/Components (Fig 7-1 Item 4)
. . . 1 . . . . . . . . . . . . . 058 427
. . . 2 . . . . . . . . . . . . . 085 980
. . . 3 . . . . . . . . . . . . . 605 941
. . . 4 . . . . . . . . . . . . . 186 437
. . . 5 . . . . . . . . . . . . . 057 971
. . . 6 . . . . . . . . . . . . . 057 745
. . . 7 . . . . . . . . . . . . . 186 435
. . . 8 . . . . . . . . . . . . . 186 436
. . . 9 . . . . . . . . . . . . . 180 915
. . . 10 . . . . . C6 . . . . 191 385
. . . 11 . . . . . . . . . . . . . 191 374
. . . 12 . . . . . . . . . . . . . 190 101
. . . 13 . . . . . . . . . . . . . 190 102
. . . 14 . . . . . . . . . . . . . 188 846
. . . 15 . . . . . . . . . . . . . 083 147
. . . 16 . . . . . . . . . . . . . 180 927
. . . 17 . . . . . . . . . . . . . 057 357
. . . 18 . . . . . R2 . . . . 091 685
. . . 20 . . . . . W . . . . 189 486
. . . 21 . . . . PC1 . . . 171 986
. . . 22 . . . . . . . . . . . . . 134 201
. . . 23 . . . . CB1 . . . 183 492
. . . 24 . . . . CB2 . . . 180 912
. . . 25 . . . . . . . . . . . . . 097 421
. . . 26 . . . . . . . . . . . . . 097 416
. . . 27 . . . . CR1 . . . 072 817
. . . 28 . . . . . . . . . . . . . . Fig 7-4
. . . . . . . . . . PLG3 . . . . 115 093
. . . . . . . . . . RC3 . . . 131 059
. . RING, retaining spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT, 625-11 .94 hex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . WASHER, flat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . SPRING, cprsn .84500 x .110W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . WASHER, flat .632 ID x 1.500 OD x .12 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . SPRING, cprsn 2.430 OD x .90 wire x 2.500 . . . . . . . . . . . . . . . . . . . . . . . .
. . HUB, spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . WASHER, brake plastic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . BAFFLE, center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CAPACITOR ASSEMBLY, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CAPACITOR, elctlt 30000uf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . BUSS BAR, positive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . BUSS BAR, negative . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . SCREW, .010-32 x .50 hex hd-slt S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . GROMMET, scr No. 8/10 panel hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . REEL SUPPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . BUSHING, snap-in nyl .937 ID x 1.125mtg hole . . . . . . . . . . . . . . . . . . . . .
. . RESISTOR, WW fxd 50W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CONTACTOR, def prp 40A 3P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CIRCUIT CARD ASSEMBLY, control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . STAND-OFF SUPPORT, PC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CIRCUIT BREAKER, man reset 10A 250V . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CIRCUIT BREAKER, man reset 5A 250V . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TERMINAL, pwr output red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TERMINAL, pwr output black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . RELAY, encl 24VAC DPDT 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . DRIVE ASSEMBLY, wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CONNECTOR & SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CONNECTOR & PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
1
1
4
1
1
8
4
1
1
1
1
1
4
1
1
1
1
1
1
1
1
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1313 Page 33
Item
No.
Part
No.
Description
169 589
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
2
2
3
4
5
6
7
8
9
9
10
10
11
12
13
14
15
16
17
18
19
20
21
22
23
23
24
25
26
. . . . . 169 715
. . . ♦087 299
. . . . . 000 067
. . . ♦000 068
. . . . . 169 716
. . . . . 170 470
. . . . . 170 471
. . . . . 169 717
. . . . . 169 718
. . . . . 169 738
. . . . . 169 719
. . . . . 169 732
. . . . . 169 720
. . . . . 169 733
. . . . . 169 721
. . . . . 172 017
. . . . . 169 735
. . . . . 169 742
. . . . . 169 743
. . . . . 169 740
. . . . . 169 746
. . . . . 169 737
. . . . . 169 741
. . . . . 180 433
. . . . . 173 521
. . . . . 079 974
. . . ♦172 257
. . . . . 172 258
. . . . . 079 975
. . . . . 169 723
. . . . . 169 739
1
Quantity
Figure 7-3. M-15 Gun (Fig 7-1 Item 36)
. . NOZZLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TIP, contact scr .023 wire x 1.125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TIP, contact scr .030 wire x 1.125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TIP, contact scr .035 wire x 1.125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . ADAPTER, contact tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . RING, retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . O-RING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . WASHER, shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TUBE, head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT, locking handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT, jam (gun end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT, jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CONNECTOR, cable (gun end) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CONNECTOR, cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT, connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . M15 UNICABLE CLAMP KIT, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CLIP, compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . TUBE, support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CLAMP, inner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CLAMP, jacket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CONNECTOR, switch lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . HANDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . STRAIN RELIEF, cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CABLE, trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CONNECTOR, feeder (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . O-RING, .500 ID x .103CS rbr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . KIT, liner monocoil .023/.025 wire x 15ft (consisting of) . . . . . . . . . . . . . . . . . . . . . . . .
. . KIT, liner monocoil .030/.035 wire x 15ft (consisting of) . . . . . . . . . . . . . . . . . . . . . . . .
. . . . O-RING, .187 ID x .103CS rbr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . GUIDE, outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . SWITCH, trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
4 5 6
7
1
2
2
2
1
1
1
2
1
2
1
1
1
1
2
2
1
1
1
1
2
2
2
1
1
2
1
1
1
1
1
. Hardware is common and
not available unless listed.
6
8
9
10
11
13
14
15
23
24
12*
25
21
22
16
18
26
17
20
19
17
9
8
10
11
16
*Includes Item 17
18
19
Figure 7-3. M-15 Gun
ST-801 140
♦OPTIONAL
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1313 Page 34
Item
No.
Part
No.
Description
Quantity
Figure 7-4. Drive Assembly, Wire (Fig 7-2 Item 29)
. . . 1 . . . . . . . . . . . . . 180 926
. . . 2 . . . . . . . . . . . . . 180 929
. . . 3 . . . . . . . . . . . . . 126 838
. . . 4 . . . . . . . . . . . . . 092 237
. . . 5 . . . . . . . . . . . . . 090 415
. . . 6 . . . . . . . . . . . . . 085 244
. . . 7 . . . . . . . . . . . . . 085 242
. . . 8 . . . . . . . . . . . . . 090 416
. . . 9 . . . . . . . . . . . . . 124 817
. . . 10 . . . . . . . . . . . . . 090 443
. . . . . . . . . . . . . . . . . . . . 111 622
. . . 11 . . . . . . . . . . . . . . 112 031
. . . 12 . . . . . . . . . . . . . 151 828
. . . 13 . . . . . . . . . . . . . 124 778
. . . 14 . . . . . . . . . . . . . 174 609
. . . 15 . . . . . . . . . . . . . 090 423
. . . 16 . . . . . . . . . . . . . 058 549
. . . 17 . . . . . . . . . . . . . 010 224
. . MOTOR, gear 24VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . HOUSING, motor drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . DRIVE ASSEMBLY, wire (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . KNOB, adjustment tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . SPRING, cprsn .720 OD x .072 wire x 1.250 . . . . . . . . . . . . . . . . . . . . . .
. . . . WASHER, cupped stl .328 ID x .812 OD x .125 lip . . . . . . . . . . . . . . . . .
. . . . FASTENER, pinned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . PIN, hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . HOUSING, wire drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . BEARING, ball rdl sgl row .315 x .866 x .27 (consisting of) . . . . . . . . . .
. . . . . . SPACER, bearing .196 ID x .310 OD x .500 collar . . . . . . . . . . . . . . . .
. . . . LEVER, pressure roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . PIN, cotter hair .054 x .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . KNOB, T 2.000 bar w/.312-18 st . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . SCREW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . ROLL, drive V groove .023-.035 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . GUIDE, wire inlet 1/16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . PIN, spring CS .187 x 1.000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
. Hardware is common and
not available unless listed.
4
5
6
7
3
8
9
10
11
12
Includes
Items
13, 16, 17
17
13
16
14
15
ST-181 053
Figure 7-4. Drive Assembly, Wire
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1313 Page 35
Notes
Notes
Notes
Effective January 1, 1998
(Equipment with a serial number preface of “KJ” or newer)
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions
below, Miller Electric Mfg. Co., Appleton, Wisconsin,
warrants to its original retail purchaser that new Miller
equipment sold after the effective date of this limited warranty
is free of defects in material and workmanship at the time it is
shipped by Miller. THIS WARRANTY IS EXPRESSLY IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING
THE
WARRANTIES OF
MERCHANTABILITY AND FITNESS.
Within the warranty periods listed below, Miller will repair or
replace any warranted parts or components that fail due to
such defects in material or workmanship. Miller must be
notified in writing within thirty (30) days of such defect or
failure, at which time Miller will provide instructions on the
warranty claim procedures to be followed.
Miller shall honor warranty claims on warranted equipment
listed below in the event of such a failure within the warranty
time periods. All warranty time periods start on the date that
the equipment was delivered to the original retail purchaser,
or one year after the equipment is sent to a North American
distributor or eighteen months after the equipment is sent to
an International distributor.
1.
2.
5 Years Parts − 3 Years Labor
*
Original main power rectifiers
*
Inverters (input and output rectifiers only)
3 Years — Parts and Labor
*
3.
Transformer/Rectifier Power Sources
*
Plasma Arc Cutting Power Sources
*
Semi-Automatic and Automatic Wire Feeders
*
Inverter Power Supplies
*
Intellitig
*
Engine Driven Welding Generators
(NOTE: Engines are warranted separately by the
engine manufacturer.)
1 Year — Parts and Labor
*
Motor Driven Guns (w/exception of Spoolmate 185)
*
Process Controllers
*
Positioners and Controllers
*
Automatic Motion Devices
*
Robots
*
IHPS Power Sources
*
Water Coolant Systems
*
HF Units
*
Grids
*
Spot Welders
*
Load Banks
*
SDX Transformers
*
Miller Cyclomatic Equipment
*
Running Gear/Trailers
*
Plasma Cutting Torches (except APT, ZIPCUT &
PLAZCUT Models)
*
Deutz Engines (outside North America)
*
Field Options
(NOTE: Field options are covered under True Blue
for the remaining warranty period of the product they
are installed in, or for a minimum of one year —
whichever is greater.)
4.
6 Months — Batteries
5.
90 Days — Parts and Labor
*
MIG Guns/TIG Torches
*
APT, ZIPCUT & PLAZCUT Model Plasma Cutting
Torches
*
Remote Controls
*
Accessory Kits
*
Replacement Parts (No labor)
*
Spoolmate 185
Miller’s True Blue Limited Warranty shall not apply to:
1.
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
2.
Consumable components; such as contact tips, cutting
nozzles, contactors, brushes, slip rings, relays or parts
that fail due to normal wear.
3.
Equipment that has been modified by any party other
than Miller, or equipment that has been improperly
installed, improperly operated or misused based upon
industry standards, or equipment which has not had
reasonable and necessary maintenance, or equipment
which has been used for operation outside of the
specifications for the equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE
AND USE BY COMMERCIAL/INDUSTRIAL USERS AND
PERSONS TRAINED AND EXPERIENCED IN THE USE
AND MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or
(2) replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the
goods at customer’s risk and expense. Miller’s option of
repair or replacement will be F.O.B., Factory at Appleton,
Wisconsin, or F.O.B. at a Miller authorized service facility as
determined by Miller. Therefore no compensation or
reimbursement for transportation costs of any kind will be
allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE
FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR
ANY OTHER LEGAL THEORY.
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN
AND ANY IMPLIED WARRANTY, GUARANTY OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
PROVISION, MIGHT ARISE BY IMPLICATION,
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE
OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL
EQUIPMENT FURNISHED BY MILLER IS EXCLUDED
AND DISCLAIMED BY MILLER.
Some states in the U.S.A. do not allow limitations of how long
an implied warranty lasts, or the exclusion of incidental,
indirect, special or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty
provides specific legal rights, and other rights may be
available, but may vary from state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated
herein, and to the extent that they may not be waived, the
limitations and exclusions set out above may not apply. This
Limited Warranty provides specific legal rights, and other
rights may be available, but may vary from province to
province.
miller_warr 1/98
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
Resources Available
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
To locate distributor nearest you call
1-800-4-A-Miller.
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Replacement Parts
Training (Schools, Videos, Books)
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
European Headquarters −
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
Welding Process Handbooks
www.MillerWelds.com
Contact the Delivering Carrier for:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims,
contact your distributor and/or equipment
manufacturer’s Transportation Department.
PRINTED IN USA
 1998 Miller Electric Mfg. Co.
9/98
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising