Miller | LG000000 | Owner Manual | Miller PROHEAT 35 RUNNING GEAR (195 436) User manual

Miller PROHEAT 35 RUNNING GEAR (195 436) User manual
OWNER’S MANUAL
OM-226 231B
Use above FORM number when ordering extra manuals.
2006−12
ProHeat 35 Running Gear
CST 8-Pack Running Gear (195 436)
1.
Safety Symbol Definitions
Warning! Watch Out! There are possible hazards as
shown in the adjoining symbols.
Falling equipment can cause serious personal injury and
equipment damage. Use lifting eye to lift unit only, not any
other accessories. Use equipment of adequate capacity
to lift unit.
Beware of electric shock from wiring. Keep all panels and
covers closed.
Have only trained and qualified persons install, operate,
or service this unit. Call your distributor if you do not
understand the directions. For INDUCTION HEATING
SAFETY and EMF information, read power source
Manual.
Wear safety glasses with side shields.
2.
Tools Needed
9/16 in
© 2005 MILLER Electric Mfg. Co.
3.
Installing Running Gear On Power Source
Y Turn off power source and
disconnect input power conductors from deenergized
supply BEFORE moving
power source.
Install casters according to the
illustration. Discard unused hardware.
Item Part
No. No.
1
2
3
4
209 479
601 965
010 910
5
602 213
Description (Qty)
Power Source
Caster (4)
Screw 375-16 x 1.00 Hex (16)
Flat Washer .406 ID x .812
OD x .65 T (16)
Lock Washer .375 Dia (16)
Be sure to provide Model and Serial Number
when ordering replacement parts.
1
2
4
5
3
Hardware Torque Chart
Hardware
Torque
ft-lbs (NVm)
3/8-16x1
20 (27)
804 325-A
OM-226 231 Page 2
4.
Installing Running Gear On Cooler
Y Turn off power source and
disconnect input power conductors from deenergized
supply BEFORE moving
power source and cooler.
Install casters according to the
illustration. Discard unused hardware.
Item Part
No. No.
1
2
3
209 479
010 910
4
5
602 213
601 965
Description (Qty)
Cooler
Caster (4)
Flat Washer .406 ID x 0.812
OD x .65 T (16)
Lock Washer .375 Dia (16)
Screw 375-16 x 1.00 Hex (16)
Be sure to provide Model and Serial Number
when ordering replacement parts.
1
3
4
2
5
Hardware Torque Chart
Hardware
Torque
ft-lbs (NVm)
3/8-16x1
20 (27)
804 326-A
OM-226 231 Page 3
5.
Installing Running Gear On CST 8-Pack Rack
Item Part
No. No.
Description (Qty)
1
2
3
209 479
601 965
010 910
4
5
602 213
601 872
Caster (4)
Screw 375-16 x 1.00 Hex (16)
Washer, Flat .406id x 0.812od
x .065t (16)
Lock Washer .375 Dia (16)
Nut, 375−16 .56 Hex (16)
Be sure to provide Model and Serial Number
when ordering replacement parts.
Hardware Torque Chart
Hardware
Torque
ft-lbs (NVm)
3/8-16x1
20 (27)
1
5
4
3
2
804 831-A
OM-226 231 Page 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising