Miller | KB000000 | Owner Manual | Miller RUNNING GEAR NO. 4MB 040021 User manual

Miller RUNNING GEAR NO. 4MB 040021 User manual
August 1991
FORM:
FOR OM-644E
Use above FORM number when ordering extra manuals.
OWNER’S MANUAL
No. 4 Running Gear 040 019
No. 4A Running Gear 040 020
11
1
10
Install handles onto
front panel and base.
IMPORTANT: Be sure
that mounting hardware maintains 1/2”
(12.7 mm) clearance
with all electrical parts.
9
8
2
7
Loosen u-bolts and install
axle/base mounting angles
on generator base. Center
axle and tighten u-bolts.
Remove paint from end of
axle and coat with grease.
Install wheels. Secure
wheels in place with retaining rings.
6
3
5
4
6
2
5
1
Install axle shaft
through
holes in cart handle assembly. Install wheels
and outside flat washers. Secure wheels in
place with retaining
rings. Install front pin
support onto generator
base. Coat bottom of
pin support with grease
and install cart handle
assembly onto pin sup- 26
port. Secure cart handle
***25
assembly onto pin support by installing flat
washer and retaining
rings.
13
8
23
24
19
16
27
29
13
18
18
**17
26
28
15
21
20
6
5
26
22
14
**Included with Item No. 19
***Included with Item No. 24
Ref. SD-047 610-F
CAUTION: UNCONTROLLED TILTING OR TIPPING of unit can result in personal injury or equipment damage.
• Use equipment of adequate capacity to lift the unit.
• If using lift forks to handle this unit, be sure the lift forks are long enough to extend out of the opposite
side of the base.
• Do not place any part of the body under the unit while it is suspended.
IMPORTANT: The running gear wheels and pin support (if applicable) require periodic greasing.
Quantity
Item
No.
Part
No.
. . . 1 . . 098 733
. . . 1 . . 022 857
. . . 2 . . 604 423
. . . 3 . . 601 949
. . . 4 . . 094 451
. . . 5 . . 601 871
. . . 6 . . 602 213
. . . 7 . *009 542
. . . 8 . . 052 305
. . . 9 . . 604 538
. . . 10 . . 602 211
. . . 11 . . 601 869
. . . 12 . . 022 825
. . . 13 . . 022 866
. . . 14 . . 022 619
. . . 15 . . 022 886
. . . . . . . . 022 622
. . . 16 . . 022 861
. . . 17 . **145 665
. . . 18 . . 133 812
. . . 19 . . 022 855
. . . 20 . . 022 609
. . . 21 . . 602 213
. . . 22 . . 601 873
. . . 23 . . 022 608
. . . 24 . . 080 512
. . . 25 ***121 614
. . . 26 . . 602 250
. . . 27 . . 097 455
. . . 28 . . 137 295
. . . 29 . . 121 614
Model
Description
No. 4 No. 4A
. . HANDLE, cart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . HANDLE, LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . GRIP, handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
. . SCREW, cap stl hexhd .312-18 x 1.000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . HANDLE, RH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . NUT, stl hex jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 . . . .
. . WASHER, lock stl split .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 . . . .
. . TUBING, stl .625 OD x 12ga wall x .187 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . SCREW, SWL head .375-16 x 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 . . . .
. . WASHER, flat stl SAE .312 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . WASHER, lock stl split .312 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . NUT, stl hex jam .312-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . WHEEL w/TIRE & BEARINGS, 8 in tire w/1 in brg .750 hub (consisting of) . . . . 2 . . . .
. . . . BEARING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
. . . . TIRE, 400/8 4 ply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . . . RIM, 8 in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . . . TUBE, 400/8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . AXLE ASSEMBLY, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . . . RING, retaining ext 1.000 shaft (included with axle) . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
. . . . WASHER, flat stl 1.062 ID x 1.500 OD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . .
. . . . AXLE, running gear (includes 2 retaining rings) . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . . . BOLT, U .375-24 x 1.000 wide x 2.000 deep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
. . . . WASHER, lock stl split .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . .
. . . . NUT, stl hex full fnsh .375-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . .
. . . . ANGLE, mtg bracket/base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
. . SUPPORT, pivot front (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . RING, retaining ext .750 shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . WASHER, flat stl SAE .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . WHEEL, rbr tire 8.000 OD x 2.031 wide x .750 bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . AXLE, running gear (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . RING, retaining ext .750 shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
*This item used only when mounting Blue Star Welding Generator to running gear.
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
OM-644 Page 2
1
2
6
6
6
2
2
1
1
1
1
2
4
1
2
4
4
2
1
1
3
2
1
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising