Miller | MB000000 | Owner Manual | Miller RUNNING GEAR, MULTI-TERRAIN - 300914 User manual

Miller RUNNING GEAR, MULTI-TERRAIN - 300914 User manual
OWNER’S MANUAL
FORM: OM-252983E
2018−02
Running Gear, Off-Road (300909)
Running Gear, Off-Road With Never Flatt Tires (300910, 300912)
Running Gear, Multi-Terrain (300913)
Running Gear, Multi-Terrain With Never Flatt Tires (300914)
Running Gear, Multi-Terrain With Protective Cage (300921)
1.
Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
DANGER ! - Indique une situation dangereuse qui, si elle
n’est pas évitée, entraînera la mort ou des blessures
graves. Les éventuels risques sont représentés par les
symboles joints ou expliqués dans le texte.
Beware of electric shock from wiring. Stop engine and
disconnect negative (−) cable from battery before installing this kit. Reinstall all panels and covers.
Attention aux chocs électriques des câbles. Arrêter le
moteur et débrancher le câble négatif de la batterie avant
d’installer cet ensemble. Réinstaller tous les panneaux et
couvercles.
Engsafe1 2013-10
Fsafe1 2013-10
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible hazards are shown in the adjoining symbols or explained in
the text.
Indique une situation dangereuse qui, si elle n’est pas
évitée, entraînera la mort ou des blessures graves. Les
éventuels risques sont représentés par les symboles
joints ou expliqués dans le texte.
Fsafe2 2013-10
Falling equipment can injure, and damage equipment.
Never put any body part under unit while lifting. Lifting
forks must extend out opposite side of base. Lift and support unit only with proper equipment and correct procedures. Follow the guidelines in the Applications Manual for
the Revised NIOSH Lifting Equation (Publication No.
94−110) when manually lifting heavy parts or equipment.
La chute de l’équipement peut provoquer des blessures
ou des dommages matériels. Ne jamais mettre une partie
du corps sous l’appareil pendant le levage. Les fourches
de levage doivent ressortir du côté opposé de la base. Ne
soulever l’appareil qu’avec un équipement en bon état
selon les procédures correctes. Suivre les consignes du
Manuel des applications pour l’équation de levage NIOSH
révisée (publication Nº 94–110) lors du levage manuel de
pièces ou équipements lourds.
Fsafe19 2013-10
NOTICE
AVIS
Indicates statements not related to personal injury.
Wear safety glasses with side shields.
Signale des consignes non associées aux dommages
corporels.
Indicates special instructions.
Porter des lunettes de sécurité avec écrans latéraux.
Fournit des instructions spéciales.
Fsafe8 2013-10
Fsafe3 2013-10
CALIFORNIA PROPOSITION 65 WARNINGS
WARNING: Cancer and Reproductive Harm − www.P65Warnings.ca.gov
PROPOSITION CALIFORIENNE 65 AVERTISSEMENTS
AVERTISSEMENT : cancer et troubles de la reproduction − www.P65Warnings.ca.gov.
Fsafe26 2018-01
© 2018 Miller Electric Mfg. LLC
2.
Assembling Off-Road Running Gear 300909 Or 300910
Tools Needed:
3/8, 9/16 in.
1
7/16, 9/16 in.
6
5
2
4
Handle attachment points
5
8
3
10
7
12
11
13
15
14
9
Item Part
No. No.
Description (Qty)
1
252635
Assy, Handle Running Gear (1)
2
3
252980
252634
Bolt, Crg Stl .250-20 X 1.750 Gr5 Pld Black (4)
Bracket, Handle (2)
. Remove paint from axle grooves be-
4
5
152461
604224
Nut, 250−20 .44hex .23h Stl Pld Sem Cone Wshr .65d (4)
Screw, 250−20 x .75 Hexwhd .50d Stl Pld Slffmg Tap−rw (6)
Assembly
6
7
601965
252631
Screw, 375−16 x 1.00 Hex Hd−pln Gr5 Pld (4)
Rail, Base Support Rh (1)
8
9
252630
602159
Rail, Base Support Lh (1)
Screw, 312−18x .75 Hexwhd.66d Stl Pld Slffmg Tap−Rw (4)
253 382
fore installing retaining rings.
Remove and discard existing hardware
from handle attachment points.
Assemble base rails, axles, and wheels
(valve stems out).
Install running gear on unit.
10 167788
Nut, 375−16 .56hex .34h Stl Pld Sem Cone Wshr .88d (4)
Install step bar on rails.
11 252981
12 235794
Attach brackets to handle. Leave loose.
Install handle assembly onto welder/generator. Tighten hardware.
13 602251
Axle, Wheel (Large) (2)
Wheel, Rbr Tire 14.500 Od X 4.750 Wide X 1.000 Bore (4)
(For 300909)
Wheel, Rbr Never Flat 14.500 Od X 4.750 Wide X 1.00 Bore (4)
(For 300910)
Washer, Flat1.062idx2.000odx.134t Stl Pld Ansi 1.00 (4)
14 145665
15 278065
Ring, Rtng Ext 1.000 Shaft X .052 Thk E Style Pld (4)
Rail, Step Bar (Running Gear) (1)
237725
Be sure to provide model when ordering replacement parts.
OM-252983 Page 2
Grease wheels through fittings.
NOTICE − Never Flat tires have a reduced
load rating. The tire set is sized to support
the unit, fuel, and weld cables only. Additional weight will damage the tires.
3.
Assembling Off-Road Running Gear With Protective Cage 300912
11
13
12
15
17
10
16
18
2
14
3
Handle attachment points
1
7
5
8
6
9
4
253 382
. Remove paint from axle grooves before installing retaining rings.
Assembly
Item Part
No. No.
Description (Qty)
1
252631
Base, Support Rh (1)
2
3
252630
167788
Base, Support Lh (1)
Nut, 375−16 .56hex .34h Stl Pld Sem Cone Wshr .88d (4)
4
5
602159
252981
Screw, 312−18x .75 Hexwhd.66d Stl Pld Slffmg Tap−Rw (4)
Axle, Wheel (Large) (2)
Install running gear on unit.
6
7
278065
237725
Rail, Step Bar (Running Gear) (1)
Wheel, Rbr Never Flat 14.500 Od X 4.750 Wide X 1.00 Bore (4)
Install handles and leave loose. Install side
rails and tighten all hardware.
8
9
602251
145665
Washer, Flat1.062idx2.000odx.134t Stl Pld Ansi 1.00 (4)
Ring, Rtng Ext 1.000 Shaft X .052 Thk E Style Pld (4)
Install cable holders with cotter pins. Apply
labels to side rails.
10 601965
Screw, 375−16 x 1.00 Hex Hd−Pln Gr5 Pld (4)
Grease wheels through fittings.
11 252635
12 152461
Assy, Handle Running Gear (2)
Nut, 250−20 .44hex .23h Stl Pld Sem Cone Wshr .65d (8)
13 604224
14 252633
Screw, 250−20 x .75 Hexwhd .50d Stl Pld Slffmg Tap−Rw (8)
Rail, Side (2)
NOTICE − Never Flat tires have a reduced
load rating. The tire set is sized to support
the unit, fuel, and weld cables only. Additional weight will damage the tires.
Tools Needed:
15 252814
16 111998
Assy, Cable Holder (4)
Pin, Cotter Hair .120 Dia X 2.375lg X .500 Shaft (4)
17 252980
18 228644
Bolt, Crg Stl .250-20 x 1.750 Gr Pld Black (8)
Label, Warning Do Not Lift (Bilingual) (2)
Be sure to provide model when ordering replacement parts.
Remove and discard existing hardware
from handle attachment points on front
and rear of unit.
Assemble base rails, axles, and wheels
(valve stems out).
Install step bar.
3/8, 9/16 in.
7/16, 9/16 in.
OM−252983 Page 3
4.
Assembling Multi-Terrain Running Gear 300913 Or 300914
12
16
14
3
13
14
15
Handle attachment points
6
4
5
7
8
4
2
10
11
9
1
3
. Remove paint from axle grooves before installing retaining rings.
Assembly
Remove and discard existing hardware
from handle attachment points.
Item Part
No. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
235793
235791
601965
167788
252631
252630
252981
235794
237725
602159
602251
145665
252635
252634
604224
152461
252980
Description (Qty)
Caster, Swvl 8.00 In Rubber X 2.000 In Wide (2)
Bracket, Mtg Caster (1)
Screw, 375−16x1.00 Hex Hd−pln Gr5 Pld (12)
Nut, 375−16 .56hex .34h Stl Pld Sem Cone Wshr.88d (12)
Rail, Base Support Rh (1)
Rail, Base Support Lh (1)
Axle, Wheel 1in Dia X 30.612 Lg (1)
Wheel, Rbr Tire 14.500 Od X 4.750 Wide X 1.000 Bore (2) (For 300913)
Wheel, Rbr Never Flat 14.5 Od X 4.75 Wide X 1” Bore (2) (For 300914)
Screw, 312−18x .75 Hex.66d Stl Pld Slffmg Tap (4)
Washer, Flat 1.062 Id X 2.0 Od X .134T Stl Pld ANSI 1.00 (2)
Ring, Rtng Ext 1.000 Shaft X .085 Thk E Style Pld (2)
Assy, Handle Running Gear (1)
Bracket, Handle (2)
Screw, 250−20x .75 Hexwhd.50d Stl Pld Slffmg Tap (6)
Nut, 250−20 .44hex .23h Stl Pld Sem Cone Wshr.65d (4)
Bolt, Crg Stl .250-20 x 1.750 Gr Pld Black (4)
Be sure to provide model when ordering replacement parts.
OM-252983 Page 4
Assemble casters to caster mounting
bracket.
Assemble base rails, axle, and wheels
(valve stems out).
Install running gear on unit.
Install caster assembly.
Install handle brackets to handle. Leave
loose.
Install handle on unit and tighten hardware.
Grease wheels through fittings.
NOTICE − Never Flat tires have a reduced
load rating. The tire set is sized to support
the unit, fuel, and weld cables only. Additional weight will damage the tires.
Tools Needed:
7/16, 9/16 in.
3/8, 9/16 in.
5.
Assembling Protective Cage With Cable Holders 300921
1
3
2
5
4
6
7
8
Handle attachment points
Tools Needed:
7/16, 9/16 in.
Item Part
No. No.
1
2
3
4
5
6
7
8
252635
152461
604224
252633
252814
252980
111998
228644
Description (Qty)
Assy, Handle Running Gear (2)
Nut, 250−20 .44hex .23h Stl Pld Sem Cone Wshr .65d (8)
Screw, 250−20 x .75 Hexwhd .50d Stl Pld Slffmg Tap−rw (8)
Rail, Side (2)
Assy, Cable Holder (4)
Screw, 250−20 x .75 Hexwhd.61d Gr5 Pld (8)
Pin, Cotter Hair .120 Dia X 2.375lg X .500 Shaft (4)
Label, Warning Do Not Lift (Bilingual) (2)
3/8, 9/16 in.
Assembly
Remove and discard existing hardware
from handle attachment points on front
and rear of unit.
Install handles. Leave loose. Install crossmembers and tighten all hardware.
Install cable holders with cotter pins. Apply
warning labels.
Be sure to provide model when ordering replacement parts.
OM−252983 Page 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising