Miller | MG030103U | Owner Manual | Miller S-74DX CE User manual

Miller S-74DX CE User manual
OM-1500-9
207749AC
2016−01
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
(Gas- And Self-Shielded)
Description
Wire Feeder
S-74DX
CE
File: MIG (GMAW)
Visit our website at
www.MillerWelds.com
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001 Quality System Warranty and service information for your
Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual specification sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 2009−09
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Symboles utilisés . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance . . . . . .
2-4. Proposition californienne 65 Avertissements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6. Informations relatives aux CEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Additional Safety Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Miscellaneous Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Serial Number And Rating Label Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Selecting A Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Rear Panel Connections And Rotating Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. 14-Pin Plug Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Wire Type, Size, And Feed Speed Capability Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Installing Welding Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6. Installing And Threading Welding Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Power Source Selection Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Operational Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4. Program Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-5. Upper Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-6. Lower Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-7. Setup Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-8. Adjust Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-9. Sequence Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-10. Auxiliary Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-11. Jog/Purge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-12. Gouge (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − SETTING SEQUENCE PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Sequence Parameters In A Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − SETTING DUAL SCHEDULE PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1. Optional Dual Schedule Switch Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-2. Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 11 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY
1
1
1
3
4
4
4
5
5
5
7
8
8
8
9
9
11
12
12
12
12
13
13
14
15
15
16
17
18
19
19
19
19
20
20
21
21
22
22
23
25
25
26
26
27
27
27
27
28
29
30
DECLARATION OF CONFORMITY
for European Community (CE marked) products.
MILLER Electric Mfg. Co., 1635 Spencer Street, Appleton, WI 54914 U.S.A. declares that the
product(s) identified in this declaration conform to the essential requirements and provisions of
the stated Council Directive(s) and Standard(s).
Product/Apparatus Identification:
Product
Stock Number
S­74DX FEEDER
S­74DX FEEDER W/LOW SPEED MOTOR
S­74DX FEEDER W/HIGH SPEED MOTOR
S­74 DX FEEDER W/CE,EURO
S­74DX FEEDER W/CE, EURO,HIGH SPEED MOTOR
S­74DX W/EURO & 4T TRIGGER HOLD
S­74DX FEEDER W/GOUGE
300618
300618001
300618002
300618003
300618004
300618005
300618006
Council Directives:
• 2006/95/EC Low Voltage
• 2004/108/EC Electromagnetic Compatibility
• 2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic equipment
Standards:
•
•
•
•
IEC 60974­1:2005 Arc welding equipment – Part 1: Welding power sources
IEC 60974­5:2007 Arc welding equipment – Part 5: Wire feeders
IEC 60974­10:2007 Arc Welding Equipment – Part 10: Electromagnetic compatibility (EMC) requirements
EN 50445:2008 Product family standard to demonstrate compliance of equipment for resistance welding,
arc welding and allied processes with the basic restrictions related to human exposure to electromagnetic
fields (0 Hz – 300Hz)
Signatory:
October 19, 2012
_____________________________________
___________________________________________
David A. Werba
Date of Declaration
MANAGER, PRODUCT DESIGN COMPLIANCE
241322G
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som 2015−09
7
Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.
1-1. Symbol Usage
DANGER! − Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in the text.
NOTICE − Indicates statements not related to personal injury.
. Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the
hazards.
1-2. Arc Welding Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information
found in the Safety Standards listed in Section 1-5. Read and
follow all Safety Standards.
Only qualified persons should install, operate, maintain, and
repair this unit.
During operation, keep everybody, especially children, away.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic
wire welding, the wire, wire reel, drive roll housing,
and all metal parts touching the welding wire are
electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
D Do not touch live electrical parts.
D Wear dry, hole-free insulating gloves and body protection.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
D Use AC output ONLY if required for the welding process.
D If AC output is required, use remote output control if present on
unit.
D Additional safety precautions are required when any of the following electrically hazardous conditions are present: in damp
locations or while wearing wet clothing; on metal structures such
as floors, gratings, or scaffolds; when in cramped positions such
as sitting, kneeling, or lying; or when there is a high risk of unavoidable or accidental contact with the workpiece or ground. For these
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone!
D Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
D Properly install, ground, and operate this equipment according to
its Owner’s Manual and national, state, and local codes.
D Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
D When making input connections, attach proper grounding conductor first − double-check connections.
D Keep cords dry, free of oil and grease, and protected from hot metal
and sparks.
D Frequently inspect input power cord and ground conductor for
damage or bare wiring – replace immediately if damaged – bare
wiring can kill.
D Turn off all equipment when not in use.
D Do not use worn, damaged, undersized, or repaired cables.
D Do not drape cables over your body.
D If earth grounding of the workpiece is required, ground it directly
with a separate cable.
D Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
D Do not touch electrode holders connected to two welding machines at the same time since double open-circuit voltage will be
present.
D Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
D Wear a safety harness if working above floor level.
D Keep all panels and covers securely in place.
D Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
D Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
D Do not connect more than one electrode or work cable to any
single weld output terminal. Disconnect cable for process not in
use.
D Use GFCI protection when operating auxiliary equipment in damp
or wet locations.
SIGNIFICANT DC VOLTAGE exists in inverter welding power sources AFTER removal of input power.
D Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
HOT PARTS can burn.
D Do not touch hot parts bare handed.
D Allow cooling period before working on
equipment.
D To handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.
OM-1500-9 Page 1
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D Keep your head out of the fumes. Do not breathe the fumes.
D If inside, ventilate the area and/or use local forced ventilation at the
arc to remove welding fumes and gases. The recommended way
to determine adequate ventilation is to sample for the composition
and quantity of fumes and gases to which personnel are exposed.
D If ventilation is poor, wear an approved air-supplied respirator.
D Read and understand the Safety Data Sheets (SDSs) and the
manufacturer’s instructions for adhesives, coatings, cleaners,
consumables, coolants, degreasers, fluxes, and metals.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
D Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements
can give off toxic fumes if welded.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear an approved welding helmet fitted with a proper shade of
filter lenses to protect your face and eyes from arc rays and
sparks when welding or watching (see ANSI Z49.1 and Z87.1
listed in Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash,
glare and sparks; warn others not to watch the arc.
D Wear body protection made from durable, flame−resistant material (leather, heavy cotton, wool). Body protection includes
oil-free clothing such as leather gloves, heavy shirt, cuffless
trousers, high shoes, and a cap.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D Do not weld where flying sparks can strike flammable material.
D Protect yourself and others from flying sparks and hot metal.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D Do not weld on containers that have held combustibles, or on
closed containers such as tanks, drums, or pipes unless they are
properly prepared according to AWS F4.1 and AWS A6.0 (see
Safety Standards).
D Do not weld where the atmosphere can contain flammable dust,
gas, or liquid vapors (such as gasoline).
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock, sparks, and fire
hazards.
D Do not use welder to thaw frozen pipes.
OM-1500-9 Page 2
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
D Wear body protection made from durable, flame−resistant material
(leather, heavy cotton, wool). Body protection includes oil-free
clothing such as leather gloves, heavy shirt, cuffless trousers, high
shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
D After completion of work, inspect area to ensure it is free of sparks,
glowing embers, and flames.
D Use only correct fuses or circuit breakers. Do not oversize or bypass them.
D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
for hot work and have a fire watcher and extinguisher nearby.
D Read and understand the Safety Data Sheets (SDSs) and the
manufacturer’s instructions for adhesives, coatings, cleaners,
consumables, coolants, degreasers, fluxes, and metals.
FLYING METAL or DIRT can injure eyes.
D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
D Wear approved safety glasses with side
shields even under your welding helmet.
BUILDUP OF GAS can injure or kill.
D Shut off compressed gas supply when not in use.
D Always ventilate confined spaces or use
approved air-supplied respirator.
ELECTRIC AND MAGNETIC FIELDS (EMF)
can affect Implanted Medical Devices.
D Wearers of Pacemakers and other Implanted
Medical Devices should keep away.
D Implanted Medical Device wearers should consult their doctor
and the device manufacturer before going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating
operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Wear approved ear protection if noise level is high.
CYLINDERS can explode if damaged.
Compressed gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D Protect compressed gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open flames, sparks, and arcs.
D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Keep cylinders away from any welding or other electrical circuits.
D Never drape a welding torch over a gas cylinder.
D Never allow a welding electrode to touch any cylinder.
D Never weld on a pressurized cylinder − explosion will result.
D Use only correct compressed gas cylinders, regulators, hoses,
and fittings designed for the specific application; maintain them
and associated parts in good condition.
D Turn face away from valve outlet when opening cylinder valve. Do
not stand in front of or behind the regulator when opening the valve.
D Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D Use the right equipment, correct procedures, and sufficient number of persons to lift and move cylinders.
D Read and follow instructions on compressed gas cylinders,
associated equipment, and Compressed Gas Association (CGA)
publication P-1 listed in Safety Standards.
1-3. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
D Do not install or place unit on, over, or near
combustible surfaces.
D Do not install unit near flammables.
D Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
FALLING EQUIPMENT can injure.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are long enough to
extend beyond opposite side of unit.
D Keep equipment (cables and cords) away from moving vehicles
when working from an aerial location.
D Follow the guidelines in the Applications Manual for the Revised
NIOSH Lifting Equation (Publication No. 94−110) when manually lifting heavy parts or equipment.
OVERUSE can cause OVERHEATING
MOVING PARTS can injure.
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
D Have only qualified persons remove doors, panels, covers, or
guards for maintenance and troubleshooting as necessary.
D Reinstall doors, panels, covers, or guards when maintenance is
finished and before reconnecting input power.
READ INSTRUCTIONS.
D Read and follow all labels and the Owner’s
Manual carefully before installing, operating, or
servicing unit. Read the safety information at
the beginning of the manual and in each
section.
D Use only genuine replacement parts from the manufacturer.
D Perform installation, maintenance, and service according to the
Owner’s Manuals, industry standards, and national, state, and
local codes.
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
H.F. RADIATION can cause interference.
FLYING SPARKS can injure.
D Wear a face shield to protect eyes and face.
D Shape tungsten electrode only on grinder with
proper guards in a safe location wearing proper
face, hand, and body protection.
D
D Sparks can cause fires — keep flammables away.
D
STATIC (ESD) can damage PC boards.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
D
D
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
MOVING PARTS can injure.
ARC WELDING can cause interference.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
WELDING WIRE can injure.
D Do not press gun trigger until instructed to do
so.
D Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
BATTERY EXPLOSION can injure.
D Do not use welder to charge batteries or jump
start vehicles unless it has a battery charging
feature designed for this purpose.
D
D
D
D
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
OM-1500-9 Page 3
1-4. California Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to
the state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after use.
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Combustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5NS
(phone: 800-463-6727, website: www.csagroup.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org).
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30329-4027 (phone: 1-800-232-4636, website:
www.cdc.gov/NIOSH).
1-6. EMF Information
Electric current flowing through any conductor causes localized electric
and magnetic fields (EMF). The current from arc welding (and allied processes including spot welding, gouging, plasma arc cutting, and
induction heating operations) creates an EMF field around the welding
circuit. EMF fields can interfere with some medical implants, e.g. pacemakers. Protective measures for persons wearing medical implants
have to be taken. For example, restrict access for passers−by or conduct individual risk assessment for welders. All welders should use the
following procedures in order to minimize exposure to EMF fields from
the welding circuit:
1. Keep cables close together by twisting or taping them, or using a
cable cover.
2. Do not place your body between welding cables. Arrange cables
to one side and away from the operator.
3. Do not coil or drape cables around your body.
OM-1500-9 Page 4
4. Keep head and trunk as far away from the equipment in the
welding circuit as possible.
5. Connect work clamp to workpiece as close to the weld as
possible.
6. Do not work next to, sit or lean on the welding power source.
7. Do not weld whilst carrying the welding power source or wire
feeder.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION
fre_som_2015−09
7
Pour écarter les risques de blessure pour vous−même et pour autrui — lire, appliquer et ranger en lieu sûr ces consignes relatives
aux précautions de sécurité et au mode opératoire.
2-1. Symboles utilisés
DANGER! − Indique une situation dangereuse qui si on
l’évite pas peut donner la mort ou des blessures graves.
Les dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
Indique une situation dangereuse qui si on l’évite pas
peut donner la mort ou des blessures graves. Les dangers possibles sont montrés par les symboles joints ou
sont expliqués dans le texte.
AVIS − Indique des déclarations pas en relation avec des blessures
personnelles.
. Indique des instructions spécifiques.
Ce groupe de symboles veut dire Avertissement! Attention! DANGER
DE CHOC ELECTRIQUE, PIECES EN MOUVEMENT, et PIECES
CHAUDES. Consulter les symboles et les instructions ci-dessous y
afférant pour les actions nécessaires afin d’éviter le danger.
2-2. Dangers relatifs au soudage à l’arc
Les symboles représentés ci-dessous sont utilisés dans ce manuel pour attirer l’attention et identifier les dangers possibles. En
présence de l’un de ces symboles, prendre garde et suivre les
instructions afférentes pour éviter tout risque. Les instructions
en matière de sécurité indiquées ci-dessous ne constituent
qu’un sommaire des instructions de sécurité plus complètes
fournies dans les normes de sécurité énumérées dans la Section 2-5. Lire et observer toutes les normes de sécurité.
Seul un personnel qualifié est autorisé à installer, faire fonctionner, entretenir et réparer cet appareil.
Pendant le fonctionnement, maintenir à distance toutes les
personnes, notamment les enfants de l’appareil.
UNE DÉCHARGE ÉLECTRIQUE peut
entraîner la mort.
Le contact d’organes électriques sous tension peut
provoquer des accidents mortels ou des brûlures
graves. Le circuit de l’électrode et de la pièce est sous
tension lorsque le courant est délivré à la sortie. Le
circuit d’alimentation et les circuits internes de la
machine sont également sous tension lorsque l’alimentation est sur Marche. Dans le mode de soudage avec
du fil, le fil, le dérouleur, le bloc de commande du
rouleau et toutes les parties métalliques en contact
avec le fil sont sous tension électrique. Un équipement
installé ou mis à la terre de manière incorrecte ou
impropre constitue un danger.
D Ne pas toucher aux pièces électriques sous tension.
D Porter des gants isolants et des vêtements de protection secs et
sans trous.
D S’isoler de la pièce à couper et du sol en utilisant des housses ou
des tapis assez grands afin d’éviter tout contact physique avec la
pièce à couper ou le sol.
D Ne pas se servir de source électrique à courant électrique dans les
zones humides, dans les endroits confinés ou là où on risque de
tomber.
D Se servir d’une source électrique à courant électrique UNIQUEMENT si le procédé de soudage le demande.
D Si l’utilisation d’une source électrique à courant électrique s’avère
nécessaire, se servir de la fonction de télécommande si l’appareil
en est équipé.
D D’autres consignes de sécurité sont nécessaires dans les conditions suivantes : risques électriques dans un environnement
humide ou si l’on porte des vêtements mouillés ; sur des structures
métalliques telles que sols, grilles ou échafaudages ; en position
coincée comme assise, à genoux ou couchée ; ou s’il y a un risque
élevé de contact inévitable ou accidentel avec la pièce à souder ou
le sol. Dans ces conditions, utiliser les équipements suivants,
dans l’ordre indiqué : 1) un poste à souder DC à tension constante
(à fil), 2) un poste à souder DC manuel (électrode) ou 3) un poste à
souder AC à tension à vide réduite. Dans la plupart des situations,
l’utilisation d’un poste à souder DC à fil à tension constante est recommandée. En outre, ne pas travailler seul !
D Couper l’alimentation ou arrêter le moteur avant de procéder à l’installation, à la réparation ou à l’entretien de l’appareil. Déverrouiller
l’alimentation selon la norme OSHA 29 CFR 1910.147 (voir normes de sécurité).
D Installez, mettez à la terre et utilisez correctement cet équipement
conformément à son Manuel d’Utilisation et aux réglementations
nationales, gouvernementales et locales.
D Toujours vérifier la terre du cordon d’alimentation. Vérifier et
s’assurer que le fil de terre du cordon d’alimentation est bien
raccordé à la borne de terre du sectionneur ou que la fiche du
cordon est raccordée à une prise correctement mise à la terre.
D En effectuant les raccordements d’entrée, fixer d’abord le conducteur de mise à la terre approprié et contre-vérifier les connexions.
D Les câbles doivent être exempts d’humidité, d’huile et de graisse;
protégez−les contre les étincelles et les pièces métalliques
chaudes.
D Vérifier fréquemment le cordon d’alimentation et le conducteur de
mise à la terre afin de s’assurer qu’il n’est pas altéré ou dénudé −,
le remplacer immédiatement s’il l’est −. Un fil dénudé peut entraîner la mort.
D L’équipement doit être hors tension lorsqu’il n’est pas utilisé.
D Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante ou mal épissés.
D Ne pas enrouler les câbles autour du corps.
D Si la pièce soudée doit être mise à la terre, le faire directement
avec un câble distinct.
D Ne pas toucher l’électrode quand on est en contact avec la pièce,
la terre ou une électrode provenant d’une autre machine.
D Ne pas toucher des porte électrodes connectés à deux machines
en même temps à cause de la présence d’une tension à vide doublée.
D N’utiliser qu’un matériel en bon état. Réparer ou remplacer sur-lechamp les pièces endommagées. Entretenir l’appareil conformément à ce manuel.
D Porter un harnais de sécurité si l’on doit travailler au-dessus du sol.
D S’assurer que tous les panneaux et couvercles sont correctement
en place.
D Fixer le câble de retour de façon à obtenir un bon contact métalmétal avec la pièce à souder ou la table de travail, le plus près possible de la soudure.
D Isoler la pince de masse quand pas mis à la pièce pour éviter le
contact avec tout objet métallique.
D Ne pas raccorder plus d’une électrode ou plus d’un câble de
masse à une même borne de sortie de soudage. Débrancher le
câble pour le procédé non utilisé.
D Utiliser une protection différentielle lors de l’utilisation d’un équipement auxiliaire dans des endroits humides ou mouillés.
Il reste une TENSION DC NON NÉGLIGEABLE dans
les sources de soudage onduleur UNE FOIS
l’alimentation coupée.
D Arrêter les convertisseurs, débrancher le courant électrique et
décharger les condensateurs d’alimentation selon les instructions
indiquées dans la partie Entretien avant de toucher les pièces.
OM-1500-9 Page 5
LES PIÈCES CHAUDES peuvent
provoquer des brûlures.
D Ne pas toucher à mains nues les parties chaudes.
D Prévoir une période de refroidissement avant
de travailler à l’équipement.
D Ne pas toucher aux pièces chaudes, utiliser les outils recommandés et porter des gants de soudage et des vêtements épais pour
éviter les brûlures.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
Le soudage génère des fumées et des gaz. Leur
inhalation peut être dangereux pour votre santé.
D Eloigner votre tête des fumées. Ne pas respirer les fumées.
D À l’intérieur, ventiler la zone et/ou utiliser une ventilation forcée au
niveau de l’arc pour l’évacuation des fumées et des gaz de
soudage. Pour déterminer la bonne ventilation, il est recommandé
de procéder à un prélèvement pour la composition et la quantité
de fumées et de gaz auxquels est exposé le personnel.
D Si la ventilation est médiocre, porter un respirateur anti-vapeurs
approuvé.
D Lire et comprendre les fiches de données de sécurité et les instructions du fabricant concernant les adhésifs, les revêtements, les
nettoyants, les consommables, les produits de refroidissement, les
dégraisseurs, les flux et les métaux.
D Travailler dans un espace fermé seulement s’il est bien ventilé ou
en portant un respirateur à alimentation d’air. Demander toujours à
un surveillant dûment formé de se tenir à proximité. Des fumées et
des gaz de soudage peuvent déplacer l’air et abaisser le niveau
d’oxygène provoquant des blessures ou des accidents mortels.
S’assurer que l’air de respiration ne présente aucun danger.
D Ne pas souder dans des endroits situés à proximité d’opérations
de dégraissage, de nettoyage ou de pulvérisation. La chaleur et
les rayons de l’arc peuvent réagir en présence de vapeurs et former des gaz hautement toxiques et irritants.
D Ne pas souder des métaux munis d’un revêtement, tels que l’acier
galvanisé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait été enlevé dans la zone de soudure, que l’endroit soit
bien ventilé, et en portant un respirateur à alimentation d’air. Les
revêtements et tous les métaux renfermant ces éléments peuvent
dégager des fumées toxiques en cas de soudage.
LES RAYONS DE L’ARC peuvent
provoquer des brûlures dans les
yeux et sur la peau.
Le rayonnement de l’arc du procédé de soudage génère
des rayons visibles et invisibles intenses (ultraviolets e
infrarouges) susceptibles de provoquer des brûlures dans les yeux et sur la
peau. Des étincelles sont projetées pendant le soudage.
D Porter un casque de soudage approuvé muni de verres filtrants
approprié pour protéger visage et yeux pour protéger votre visage
et vos yeux pendant le soudage ou pour regarder (voir ANSI Z49.1
et Z87.1 énuméré dans les normes de sécurité).
D Porter des lunettes de sécurité avec écrans latéraux même sous
votre casque.
D Avoir recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements les éblouissements
et les étincelles ; prévenir toute personne sur les lieux de ne pas
regarder l’arc.
D Porter un équipement de protection pour le corps fait d’un matériau
résistant et ignifuge (cuir, coton robuste, laine). La protection du
corps comporte des vêtements sans huile comme par ex. des
gants de cuir, une chemise solide, des pantalons sans revers, des
chaussures hautes et une casquette.
LE SOUDAGE peut provoquer un
incendie ou une explosion.
Le soudage effectué sur des conteneurs fermés tels
que des réservoirs, tambours ou des conduites peut
provoquer leur éclatement. Des étincelles peuvent
être projetées de l’arc de soudure. La projection d’étincelles, des
pièces chaudes et des équipements chauds peut provoquer des incendies et des brûlures. Le contact accidentel de l’électrode avec des
objets métalliques peut provoquer des étincelles, une explosion, un surOM-1500-9 Page 6
chauffement ou un incendie. Avant de commencer le soudage, vérifier
et s’assurer que l’endroit ne présente pas de danger.
D Déplacer toutes les substances inflammables à une distance de
10,7 m de l’arc de soudage. En cas d’impossibilité les recouvrir
soigneusement avec des protections homologués.
D Ne pas souder dans un endroit là où des étincelles peuvent tomber
sur des substances inflammables.
D Se protéger et d’autres personnes de la projection d’étincelles et
de métal chaud.
D Des étincelles et des matériaux chauds du soudage peuvent
facilement passer dans d’autres zones en traversant de petites
fissures et des ouvertures.
D Surveiller tout déclenchement d’incendie et tenir un extincteur à
proximité.
D Le soudage effectué sur un plafond, plancher, paroi ou séparation
peut déclencher un incendie de l’autre côté.
D Ne pas effectuer le soudage sur des conteneurs fermés tels que
des réservoirs, tambours, ou conduites, à moins qu’ils n’aient été
préparés correctement conformément à AWS F4.1 et AWS A6.0
(voir les Normes de Sécurité).
D Ne pas souder là où l’air ambiant pourrait contenir des poussières,
gaz ou émanations inflammables (vapeur d’essence, par
exemple).
D Brancher le câble de masse sur la pièce le plus près possible de la
zone de soudage pour éviter le transport du courant sur une
longue distance par des chemins inconnus éventuels en provoquant des risques d’électrocution, d’étincelles et d’incendie.
D Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
D En cas de non utilisation, enlever la baguette d’électrode du porteélectrode ou couper le fil à la pointe de contact.
D Porter un équipement de protection pour le corps fait d’un matériau
résistant et ignifuge (cuir, coton robuste, laine). La protection du
corps comporte des vêtements sans huile comme par ex. des
gants de cuir, une chemise solide, des pantalons sans revers, des
chaussures hautes et une casquette.
D Avant de souder, retirer toute substance combustible de vos poches telles qu’un allumeur au butane ou des allumettes.
D Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
D Suivre les recommandations dans OSHA 1910.252(a)(2)(iv) et
NFPA 51B pour les travaux à chaud et avoir de la surveillance et un
extincteur à proximité.
D Lire et comprendre les fiches de données de sécurité et les instructions du fabricant concernant les adhésifs, les revêtements, les
nettoyants, les consommables, les produits de refroidissement,
les dégraisseurs, les flux et les métaux.
DES PIECES DE METAL ou DES
SALETES peuvent provoquer des
blessures dans les yeux.
D Le soudage, l’écaillement, le passage de la pièce à
la brosse en fil de fer, et le meulage génèrent des étincelles et des
particules métalliques volantes. Pendant la période de refroidissement des soudures, elles risquent de projeter du laitier.
D Porter des lunettes de sécurité avec écrans latéraux ou un écran
facial.
LES ACCUMULATIONS DE GAZ
risquent de provoquer des blessures
ou même la mort.
D Fermer l’alimentation du gaz comprimé en cas
de non utilisation.
D Veiller toujours à bien aérer les espaces confinés ou se servir d’un
respirateur d’adduction d’air homologué.
Les CHAMPS ÉLECTROMAGNÉTIQUES
(CEM) peuvent affecter les implants médicaux.
D Les porteurs de stimulateurs cardiaques et
autres implants médicaux doivent rester à
distance.
D Les porteurs d’implants médicaux doivent consulter leur médecin
et le fabricant du dispositif avant de s’approcher de la zone où se
déroule du soudage à l’arc, du soudage par points, du gougeage,
de la découpe plasma ou une opération de chauffage par
induction.
LE BRUIT peut endommager l’ouïe.
Le bruit des processus et des équipements peut
affecter l’ouïe.
D Porter des protections approuvées pour les
oreilles si le niveau sonore est trop élevé.
LES BOUTEILLES peuvent exploser
si elles sont endommagées.
Les bouteilles de gaz comprimé contiennent du
gaz sous haute pression. Si une bouteille est
endommagée, elle peut exploser. Du fait que
les bouteilles de gaz font normalement partie du procédé de
soudage, les manipuler avec précaution.
D Protéger les bouteilles de gaz comprimé d’une chaleur excessive,
des chocs mécaniques, des dommages physiques, du laitier, des
flammes ouvertes, des étincelles et des arcs.
D Placer les bouteilles debout en les fixant dans un support stationnaire ou dans un porte-bouteilles pour les empêcher de tomber ou
de se renverser.
D Tenir les bouteilles éloignées des circuits de soudage ou autres
circuits électriques.
D Ne jamais placer une torche de soudage sur une bouteille à gaz.
D Une électrode de soudage ne doit jamais entrer en contact avec
une bouteille.
D Ne jamais souder une bouteille pressurisée − risque d’explosion.
D Utiliser seulement des bouteilles de gaz comprimé, régulateurs,
tuyaux et raccords convenables pour cette application spécifique;
les maintenir ainsi que les éléments associés en bon état.
D Tourner le dos à la sortie de vanne lors de l’ouverture de la vanne
de la bouteille. Ne pas se tenir devant ou derrière le régulateur lors
de l’ouverture de la vanne.
D Le couvercle du détendeur doit toujours être en place, sauf lorsque
la bouteille est utilisée ou qu’elle est reliée pour usage ultérieur.
D Utiliser les équipements corrects, les bonnes procédures et suffisamment de personnes pour soulever et déplacer les bouteilles.
D Lire et suivre les instructions sur les bouteilles de gaz comprimé,
l’équipement connexe et le dépliant P-1 de la CGA (Compressed Gas
Association) mentionné dans les principales normes de sécurité.
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance
Risque D’INCENDIE OU D’EXPLOSION.
D Ne pas placer l’appareil sur, au-dessus ou
à proximité de surfaces inflammables.
D Ne pas installer l’appareil à proximité de produits inflammables.
D Ne pas surcharger l’installation électrique − s’assurer que
l’alimentation est correctement dimensionnée et protégée avant
de mettre l’appareil en service.
LES CHARGES ÉLECTROSTATIQUES peuvent endommager les circuits imprimés.
D Établir la connexion avec la barrette de terre
avant de manipuler des cartes ou des pièces.
D Utiliser des pochettes et des boîtes antistatiques pour stocker,
déplacer ou expédier des cartes de circuits imprimes.
Les PIÈCES MOBILES peuvent
causer des blessures.
LA CHUTE DE L’ÉQUIPEMENT peut
provoquer des blessures.
D Utiliser l’anneau de levage uniquement pour
soulever l’appareil, NON PAS les chariots, les
bouteilles de gaz ou tout autre accessoire.
D Utiliser un équipement de levage de capacité suffisante pour lever
l’appareil.
D En utilisant des fourches de levage pour déplacer l’unité, s’assurer
que les fourches sont suffisamment longues pour dépasser du
côté opposé de l’appareil.
D Tenir l’équipement (câbles et cordons) à distance des véhicules
mobiles lors de toute opération en hauteur.
D Suivre les consignes du Manuel des applications pour l’équation
de levage NIOSH révisée (Publication Nº94–110) lors du levage
manuelle de pièces ou équipements lourds.
L’EMPLOI EXCESSIF peut
SURCHAUFFER L’ÉQUIPEMENT.
D Prévoir une période de refroidissement ; respecter le cycle opératoire nominal.
D Réduire le courant ou le facteur de marche
avant de poursuivre le soudage.
D Ne pas obstruer les passages d’air du poste.
LES ÉTINCELLES PROJETÉES
peuvent provoquer des blessures.
D Porter un écran facial pour protéger le visage et
les yeux.
D Affûter l’électrode au tungstène uniquement à
la meuleuse dotée de protecteurs. Cette manœuvre est à exécuter dans un endroit sûr lorsque l’on porte l’équipement homologué de protection du visage, des mains et du corps.
D Les étincelles risquent de causer un incendie − éloigner toute
substance inflammable.
D Ne pas s’approcher des organes mobiles.
D Ne pas s’approcher des points de coincement
tels que des rouleaux de commande.
LES FILS DE SOUDAGE peuvent
provoquer des blessures.
D Ne pas appuyer sur la gâchette avant d’en
avoir reçu l’instruction.
D Ne pas diriger le pistolet vers soi, d’autres
personnes ou toute pièce mécanique en engageant le fil de
soudage.
L’EXPLOSION DE LA BATTERIE
peut provoquer des blessures.
D Ne pas utiliser l’appareil de soudage pour
charger des batteries ou faire démarrer des
véhicules à l’aide de câbles de démarrage,
sauf si l’appareil dispose d’une fonctionnalité
de charge de batterie destinée à cet usage.
Les PIÈCES MOBILES peuvent
causer des blessures.
D S’abstenir de toucher des organes mobiles tels
que des ventilateurs.
D Maintenir fermés et verrouillés les portes,
panneaux, recouvrements et dispositifs de protection.
D Lorsque cela est nécessaire pour des travaux d’entretien et de dépannage, faire retirer les portes, panneaux, recouvrements ou
dispositifs de protection uniquement par du personnel qualifié.
D Remettre les portes, panneaux, recouvrements ou dispositifs de
protection quand l’entretien est terminé et avant de rebrancher
l’alimentation électrique.
LIRE LES INSTRUCTIONS.
D Lire et appliquer les instructions sur les
étiquettes et le Mode d’emploi avant l’installation, l’utilisation ou l’entretien de l’appareil.
Lire les informations de sécurité au début du
manuel et dans chaque section.
OM-1500-9 Page 7
D N’utiliser que les pièces de rechange recommandées par le
constructeur.
D Effectuer l’installation, l’entretien et toute intervention selon les
manuels d’utilisateurs, les normes nationales, provinciales et de
l’industrie, ainsi que les codes municipaux.
LE SOUDAGE À L’ARC risque de
provoquer des interférences.
D L’énergie électromagnétique risque de
provoquer des interférences pour l’équipement
électronique sensible tel que les ordinateurs et
l’équipement commandé par ordinateur tel que
les robots.
LE
RAYONNEMENT
HAUTE
FRÉQUENCE
(H.F.)
risque
de
provoquer des interférences.
D Le rayonnement haute fréquence (H.F.) peut
provoquer des interférences avec les équipements de radio−navigation et de communication, les services
de sécurité et les ordinateurs.
D Demander seulement à des personnes qualifiées familiarisées avec
des équipements électroniques de faire fonctionner l’installation.
D L’utilisateur est tenu de faire corriger rapidement par un électricien
qualifié les interférences résultant de l’installation.
D Si le FCC signale des interférences, arrêter immédiatement l’appareil.
D Effectuer régulièrement le contrôle et l’entretien de l’installation.
D Maintenir soigneusement fermés les portes et les panneaux des
sources de haute fréquence, maintenir les éclateurs à une distance correcte et utiliser une terre et un blindage pour réduire les
interférences éventuelles.
D Veiller à ce que tout l’équipement de la zone de soudage soit compatible électromagnétiquement.
D Pour réduire la possibilité d’interférence, maintenir les câbles de
soudage aussi courts que possible, les grouper, et les poser aussi
bas que possible (ex. par terre).
D Veiller à souder à une distance de 100 mètres de tout équipement
électronique sensible.
D Veiller à ce que ce poste de soudage soit posé et mis à la terre
conformément à ce mode d’emploi.
D En cas d’interférences après avoir pris les mesures précédentes,
il incombe à l’utilisateur de prendre des mesures supplémentaires
telles que le déplacement du poste, l’utilisation de câbles blindés,
l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone
de travail.
2-4. Proposition californienne 65 Avertissements
Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des malformations congénitales et, dans certains cas, des cancers.
(Code de santé et de sécurité de Californie, chapitre 25249.5
et suivants)
Ce produit contient des produits chimiques, notamment du
plomb, dont l’État de Californie reconnaît qu’ils provoquent
des cancers, des malformations congénitales ou d’autres
problèmes de procréation. Se laver les mains après
utilisation.
2-5. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Combustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5NS
(phone: 800-463-6727, website: www.csagroup.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org).
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30329-4027 (phone: 1-800-232-4636, website:
www.cdc.gov/NIOSH).
2-6. Informations relatives aux CEM
Le courant électrique qui traverse tout conducteur génère des champs
électromagnétiques (CEM) à certains endroits. Le courant issu d’un
soudage à l’arc (et de procédés connexes, y compris le soudage par
points, le gougeage, le découpage plasma et les opérations de
chauffage par induction) crée un champ électromagnétique (CEM)
autour du circuit de soudage. Les champs électromagnétiques produits
peuvent causer interférence à certains implants médicaux, p. ex. les
stimulateurs cardiaques. Des mesures de protection pour les porteurs
d’implants médicaux doivent être prises: Limiter par exemple tout accès
aux passants ou procéder à une évaluation des risques individuels pour
les soudeurs. Tous les soudeurs doivent appliquer les procédures
suivantes pour minimiser l’exposition aux CEM provenant du circuit de
soudage:
1. Rassembler les câbles en les torsadant ou en les attachant avec
du ruban adhésif ou avec une housse.
2. Ne pas se tenir au milieu des câbles de soudage. Disposer les
OM-1500-9 Page 8
câbles d’un côté et à distance de l’opérateur.
3. Ne pas courber et ne pas entourer les câbles autour de votre
corps.
4. Maintenir la tête et le torse aussi loin que possible du matériel du
circuit de soudage.
5. Connecter la pince sur la pièce aussi près que possible de la
soudure.
6. Ne pas travailler à proximité d’une source de soudage, ni
s’asseoir ou se pencher dessus.
7. Ne pas souder tout en portant la source de soudage ou le
dévidoir.
En ce qui concerne les implants médicaux :
Les porteurs d’implants doivent d’abord consulter leur médecin avant
de s’approcher des opérations de soudage à l’arc, de soudage par
points, de gougeage, du coupage plasma ou de chauffage par induction. Si le médecin approuve, il est recommandé de suivre les
procédures précédentes.
SECTION 3 − DEFINITIONS
3-1. Additional Safety Symbols And Definitions
. Some symbols are found only on CE products.
Warning! Watch Out! There are possible hazards as shown by the symbols.
Safe1 2012−05
Do not discard product (where applicable) with general waste.
Reuse or recycle Waste Electrical and Electronic Equipment (WEEE) by disposing at a designated collection
facility.
Contact your local recycling office or your local distributor for further information.
Safe37 2012−05
Wear dry insulating gloves. Do not touch electrode (wire) with bare hand. Do not wear wet or damaged gloves.
Safe57 2012−05
Protect yourself from electric shock by insulating yourself from work and ground.
Safe58 2012−06
Disconnect input plug or power before working on machine.
Safe5 2012−05
Keep your head out of the fumes.
Safe59 2012−05
Use forced ventilation or local exhaust to remove the fumes.
Safe60 2012−06
Use ventilating fan to remove fumes.
Safe61 2012−06
Keep flammables away from welding. Do not weld near flammables.
Safe62 2012−06
Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Safe63 2012−06
OM-1500-9 Page 9
Do not weld on drums or any closed containers.
?
Safe64 2012−06
Do not remove or paint over (cover) the label.
Safe20 2012−05
Drive rolls can injure fingers.
Safe32 2012−05
Welding wire and drive parts are at welding voltage during operation − keep hands and metal objects away.
Safe33 2012−05
Wear hat and safety glasses. Use ear protection and button shirt
collar. Use welding helmet with correct shade of filter. Wear complete
body protection.
Safe66 2012−06
Become trained and read the instructions before working on the
machine or welding.
Safe65 2012−06
Notes
OM-1500-9 Page 10
3-2. Miscellaneous Symbols And Definitions
. Some symbols are found only on CE products.
A
Amperes
Direct Current
(DC)
IP
Hz
I2
Rated Welding
Current
Program
Degree Of
Protection
Preflow Time
Set Up
Process
U1
Variable
Inductance
Hertz
Increase
Three Phase
U2
Output
X
Input
Conventional
Load Voltage
Constant Current
Time
Trigger Hold Off
Cold Jog (Inch)
Towards
Workpiece
I1
Percent
Primary Current
Wire Type
Circuit Breaker
Gas Input
Duty Cycle
Line Connection
Wire Feed
Postflow Time
Primary Voltage
Trigger Hold On
Arc Control
Sequence
Single Phase
Gas Type
Read Instructions
Purge By Gas
Trigger Control
Constant Voltage
V
Volts
OM-1500-9 Page 11
SECTION 4 − SPECIFICATIONS
4-1. Serial Number And Rating Label Location
The serial number and rating information for this product is located on the rear panel. Use rating label to determine input power requirements and/or
rated output. For future reference, write serial number in space provided on back cover of this manual.
4-2. Unit Specifications
Type of
Input Power
Welding Power
Source Type
24 Volts AC
Single-Phase
10 Amperes
50/60 Hertz
Constant Voltage
(CV)
DC With 14-Pin
And Contactor
Control
Wire Feed Speed
Standard: 50 To 780 ipm
(1.2 To 19.8 mpm)
Optional High Speed:
92 To 1435 ipm
(2.3 To 36.4 mpm)
Wire Diameter
Range
Welding Circuit Rating
Max Spool Weight:
60 lb (27 kg)
(See Section 5-4)
100 Volts,
750 Amperes, 100%
Duty Cycle
Max Spool Capacity:
18 in. (457 mm)
Overall
Dimensions
Weight
Length: 27 in.
(686 mm)
45 lb
(20.4 kg)
Width: 12-1/2 in.
(318 mm)
Height: 14 in.
(356 mm)
Optional Low Speed:
19 to 300 ipm
(0.4 to 7.6 mpm)
4-3. Environmental Specifications
A. IP Rating
IP Rating
This equipment is designed for indoor use and is not intended to be used or stored outside.
IP2X 2014−06
B. Information On Electromagnetic Fields (EMF)
!
This equipment shall not be used by the general public as the EMF limits for the general public might be exceeded during welding.
This equipment is built in accordance with EN 60974−1 and is intended to be used only in an occupational environment (where the general public
access is prohibited or regulated in such a way as to be similar to occupational use) by an expert or an instructed person.
Wire feeders and ancillary equipment (such as torches, liquid cooling systems and arc striking and stabilizing devices) as part of the welding
circuit may not be a major contributor to the EMF. See the Owner’s Manuals for all components of the welding circuit for additional EMF exposure
information.
S
S
The EMF assessment on this equipment was conducted at 0.5 meter.
At a distance of 1 meter the EMF exposure values were less than 20% of the permissible values.
ce-emf 1 2010-10
C. Information On Electromagnetic Compatibility (EMC)
!
This Class A equipment is not intended for use in residential locations where the electrical power is provided by the public low−
voltage supply system. There can be potential difficulties in ensuring electromagnetic compatibility in those locations, due to conducted as well as radiated disturbances.
ce-emc 3 2014-07
OM-1500-9 Page 12
SECTION 5 − INSTALLATION
5-1. Selecting A Location
!
Do not put feeder where
welding wire hits cylinder.
. Wire feeder shown is representative only and may not
reflect actual unit.
3
4
1
Wire Feeder
2
Rubber Feet
Choose slot that allows all rubber
feet to sit securely on top of welding
power source.
1
3
Wire Spool/Reel
4
Gas Cylinder w/Hose And
Regulator (Customer
Supplied)
5
. Shielding gas pressure not to
exceed 100 psi (689 kPa).
2
5
Welding Power Source
6
Running Gear
6
!
Do not move or operate unit where it could tip.
loc_feeder/cart 2015-05
OM-1500-9 Page 13
5-2. Rear Panel Connections And Rotating Drive Assembly
1
2
14-Pin Control Cable − 10 ft
(3.0 m)
Shielding Gas Valve Fitting
Requires fitting with 5/8-18 righthand threads. Connect customersupplied gas hose.
. Shielding gas pressure not to
exceed 100 PSI (689 kPa).
3
4
5
6
2
Weld Cable Terminal
Weld Cable
Drive Assembly
Drive Assembly Rotation
Knob
To rotate the drive assembly, loosen drive assembly rotation knob,
rotate drive assembly, and tighten
knob.
1
3
4
5
6
Tools Needed:
9/16, 5/8 in.
3/16 in.
Ref. 805 079-B / 246 041-A
OM-1500-9 Page 14
5-3. 14-Pin Plug Information
Pin*
A
24 volts AC with respect to socket G.
A
B
Contact closure to A completes 24 volts AC contactor control circuit.
B
L C
M D
E
G
Circuit common for 24 volts AC circuit.
C
+10 volts DC input from power source to wire feeder with respect to socket D.
D
Remote control circuit common.
E
0 to +10 volts DC output signal from wire feeder to power source with respect to socket D.
H
Voltage feedback; 0 to +10 volts DC, 1 volt per 10 arc volts.
F
Current feedback; 0 to +10 volts DC, 1 volt per 100 amperes.
J
K
I
H
N
G
F
Pin Information
*The remaining pins are not used.
5-4. Wire Type, Size, And Feed Speed Capability Table
Motor Speed
Wire Type
Wire Size
Rated Speed Range (per IEC 60974-5)
Standard
Standard
All
.023 To 5/64 in. (0.6 To 2 mm)
55 To 770 ipm (1.4 To 19.5 mpm)
All
3/32 To 7/64 in. (2.4 To 2.8 mm)
55 To 700 ipm (1.4 To 17.8 mpm)
Standard
All
1/8 in. (3.2 mm)
55 To 300 ipm (1.4 To 7.6 mpm)
Optional High
Speed
All
.023 To 5/64 in. (0.6 To 2 mm)
92 To 1435 ipm (2.3 To 36.4 mpm)
Optional Low
Speed
All
.0233 To 1/8 in. (0.6 To 3.2 mm)
19 To 300 ipm (0.4 To 7.6 mpm)
Notes
OM-1500-9 Page 15
5-5. Installing Welding Gun
1
2
3
4
6
Gun Locking Tab
Power Clamp Knob
Gun Connection End
Power Pin Groove
Installing gun with Accu-Mate
connection
5
Loosen power clamp knob to allow
power pin of gun to clear the gun
locking tab.
Push power pin into power clamp
as far as possible to align the
groove in the power pin of the gun
with the gun locking tab.
Secure gun by tightening power
clamp knob.
Installing gun without AccuMate connection
4
3
When using a gun without the
groove in the power pin, loosen
power clamp knob and rotate gun
locking tab 180 degrees. This prevents the locking tab from extending into the power pin gun connection.
Push power pin into power clamp
as far as possible.
Installing gun with
Accu-Mate connection
1
Installing gun without
Accu-Mate connection
2
1
Secure gun by tightening power
clamp knob.
2
5
6
Empty Pressure Slots
Pressure Blocking Clip
Ref. 249 398-A
OM-1500-9 Page 16
5-6. Installing And Threading Welding Wire
Install wire guides and
anti-wear guide.
Install wire spool. Adjust tension nut so
wire is taut when wire feed stops.
Install drive rolls.
Pressure
Adjust
Rear
Rolls
Pressure
Indicator
Scale
Pressure
Adjust
Front
Rolls
No Wire Slip
Wire Slips
NONCONDUCTIVE
SURFACE
NONCONDUCTIVE
SURFACE
Drive Rolls
Tools Needed:
3/16, 5/64 in.
Gun Cable
15/16, 3/8 in.
End Of Liner
. Be sure that outlet cable has proper size . For soft wire or small diameter stainless . To adjust drive roll pressure, hold nozzle
liner for the welding wire size. When
installing
gun,
position
liner
extending from outlet wire guide as
close as possible to drive rolls without
touching.
Install gun. Lay gun cable out straight. Cut off
end of wire. Push wire through guides up to
drive rolls; continue to hold wire. Press Jog
button to feed wire out gun.
steel wire, reduce drive roll pressure on
the rear roll to half that of the front rolls.
about 2 in. (51 mm) from nonconductive
surface and press gun trigger to feed wire
against surface. Tighten knob so wire
does not slip. Do not overtighten. If contact tip is completely blocked, wire should
slip at the feeder (see pressure adjustment above).Cut wire off. Close cover.
Ref. 805 079-A /156 929-A / Ref. 150 922 / Ref. 156 930 / 802 954 / S-0627-A
OM-1500-9 Page 17
5-7. Power Source Selection Menu
1
2
1
Upper Display
Lower Display
. When the feeder is turned on,
the Power Source Selection
Menu allows the operator to select a default power source.
Selecting a default power
source, automatically sets the
correct Vmin and Vmax settings for adjusting the output
voltage of the power source.
First Time Feeder Is Turned On
2
Upper Display
Lower Display
Deltaweld 452
dELT
452
Vmin =10
Vmax =38
Deltaweld 302
dELT
302
Vmin =10
Vmax =32
Deltaweld 652
dELT
652
Vmin =10
Vmax =44
* * Power Source
Voltage Range
Dimension 302
dIM
302
Vmin =10
Vmax =32
Dimension NT 450
dIM
450
Vmin =10
Vmax =38
Dimension 452
dIM
452
Vmin =10
Vmax =38
Dimension 652
dIM
652
Vmin =10
Vmax =65
Dimension 1000
dIM
1000
Vmin =10
Vmax =60
XMT 304
XMT
304
Vmin =10
Vmax =35
XMT 350
XMT
350
Vmin =10
Vmax =38
XMT 456
XMT
456
Vmin =10
Vmax =38
Invision 350 MPa
I350
MPa
Vmin =10
Vmax =38
Invision 354MP
I354
MP
Vmin =10
Vmax =35
Invision 456MP
I456
MP
Vmin =10
Vmax =38
Invision 456P
I456
P
Vmin =10
Vmax =38
PHOENIX 456
PHX
456
Vmin =10
Vmax =38
SUMMIT ARC 1000
SUM
1000
Vmin =25
Vmax =44
** For any power sources not listed, pick a matching voltage range, or see Sec 5-10 to
set Vmin and Vmax.
OM-1500-9 Page 18
The feeder automatically goes into
the Power Source Selection Menu.
The feeder displays “dELT” on the
Upper Display and “452” on the
Lower Display, meaning that a Deltaweld 452 is the default power
source, and has a voltage range of
10V as Vmin and 38V as Vmax.
At power up, the operator has three
seconds to select a default power
source from the list shown on the
display. Operator may scroll
through the list of power sources by
using the Adjust control. After selecting a power source the operator
has three seconds to change to a
different power source or begin
welding. After making a power
source selection, the operator may
press the Program Button to avoid
having to wait the three seconds.
When turning off the feeder, the default power source will be retained.
If voltage settings have already
been set with the Vmin and Vmax in
the Auxiliary Menu, selecting a default power source with the Power
Source Selection Menu overrides
the Vmin and Vmax voltage settings.
Next Time Feeder Is Turned On
The feeder will display the last selected default power source. The
operator has three seconds to select another power source, or press
the Program Button to exit the Power Source Selection Menu.
Disabling The Power Source
Selection Menu
Once the default power source has
been selected the Power Source
Selection Menu may be disabled
using the Auxiliary Menus. See
Section 6-10.
SECTION 6 − OPERATION
6-1. Operational Terms
The following is a list of terms and their definitions as they apply to this wire feeder:
General Terms:
Cold Wire Jog
Feeding wire without contactor or gas valve being energized.
Sequence
A portion of the weld program, such as preflow, run-in, start, weld, crater, burnback, and postflow.
Weld Program
A group of sequences that make up a weld cycle.
6-2. Power Switch
1
Power Switch
1
805 081-A
6-3. Front Panel Controls
Nameplate
See
Section
6-5
See
Section
6-4
See
Section
6-6
See
Section
6-9
See
Section
6-8
See
Section
6-7
OM-1500-9 Page 19
6-4. Program Push Button
1
Program Display
The number of the active program
is displayed.
2
Program Push Button
Press button to activate program
select feature. To change the program number, press the Program
push button and rotate the Adjust
control.
3
1
Program Push Button LED
The LED lights to indicate the Program push button is active.
3
2
6-5. Upper Display
3
1
2
4
5
. To set the correct voltage range for a par-
ticular power source, see Section 5-7 for
power source selection menu, or Section
6-10 for V-Min And V-Max adjustments.
1 Upper Display
The upper display shows voltage or time. The
unit displays both preset and actual arc voltage. When the unit is in a welding state, actual
arc voltage is displayed. The upper display
shows welding sequence time when the Time
LED is illuminated.
2 Upper Display Push Button
Press and hold button to adjust or display weld
time. Release button to display voltage.
OM-1500-9 Page 20
3 Upper Display Push Button LED
The upper display push button LED illuminates to indicate that information displayed
can be changed by the Adjust control.
4 Volts LED
5 Time LED
The LEDs below the display illuminate to indicate which value is being shown.
At any time while welding, the unit permits the
adjustment of the weld sequence voltage and
overrides the display of actual arc voltage.
• If the unit is displaying a welding sequence
that can be timed, the welding time display
mode is entered by pressing the upper dis-
play push button repeatedly until welding
time is the active parameter in the upper display. At idle, the upper display toggles between showing weld voltage or weld time,
with subsequent presses of the upper display push button.
• The unit defaults to displaying welding voltage when a welding sequence display
mode is first entered.
• If the weld sequence has a time set (as in
spot time), after the weld program is completed, ERR TRG 1 will be displayed to indicate the weld program is complete. Release
trigger to clear error.
6-6. Lower Display
3
1
2
4
5
1
Lower Display
to indicate that information displayed can be
changed by the Adjust control.
The lower display shows wire speed or
amperage. The unit displays and adjusts only
preset wire speed at idle. When the unit is in
a welding state, actual wire speed is displayed
for the active welding sequence.
2
4
5
The LEDs below the display illuminate to indicate which value is being shown.
Lower Display Push Button
• If the unit is in a welding state that does not
involve feeding wire, the unit displays the
weld sequence wire speed. At any time during welding, the weld sequence wire speed
can be adjusted and overrides the preset
wire speed display. In other words, if the Ad-
Press button to choose between wire speed or
amperage functions.
3
Wire Speed LED
Amps LED
Lower Display Push Button LED
The lower display push button LED illuminates
just control is activated while welding, the
unit displays and permits adjustment of the
weld sequence wire feed speed regardless
of the active welding sequence.
• When the unit is displaying amperage, the
Amps LED illuminates. Amperage is only
displayed if the unit is in a welding state and
the amperage is above a minimum value of
25 Amps.
• The display will read dashes for amperage
readings below the amperage threshold,
prior to arc initiation.
6-7. Setup Push Button
3
4
2
1
1 Setup Push Button
Press button to choose between trigger hold
or dual schedule functions.
2 Setup Push Button LED
3 Trigger Hold LED
4 Dual Schedule LED
• When the Setup button is pressed, the Setup push button LED flashes and the Trigger
Hold LED flashes.
• The flashing LED indicates that the unit is in
the trigger hold display mode. In this mode
the upper display indicates HOLD and the
lower display indicates the trigger hold status On/Off. Use the Adjust control to change
the trigger hold status or press the lower display push button. If trigger hold is turned On,
the trigger hold LED illuminates and stays
On.
• When trigger hold is On, the user must
press and hold the trigger for a predefined
amount of time (the trigger hold delay time−
see Section 6-10), then release it for the trigger hold function to be active. To shut off the
weld when trigger hold is On, the user must
press and release the trigger.
• If a weld time is programmed, trigger hold is
disabled.
• Trigger hold and dual schedule cannot be
used concurrently.
• When the Setup button is pressed a second
time, the dual schedule LED flashes. In this
mode the upper display indicates DUAL and
the lower display indicates dual schedule
status On/Off. Use the Adjust control to
change the dual schedule status if desired.
• Pressing the Setup button again exits the
Setup mode. The dual schedule LED stops
flashing to indicate the dual schedule status
is Off.
• While in the Setup mode, the active program
can be adjusted without deactivating the
trigger hold Setup mode operation. If the
trigger is activated, Setup mode(s) is terminated.
OM-1500-9 Page 21
6-8. Adjust Control
1
Adjust Control
The Adjust control is used to
change various sequence parameters, and to select various sequences. Refer to the section for
the function in question for information related to using the Adjust control.
1
6-9. Sequence Push Button
3
Start
Time
2
Preflow
Time
Weld
Time
Crater
Time
Postflow
Time
1
Welding Sequence Diagram
1
2
3
Sequence Push Button
Sequence Push Button LED
Welding Sequence LEDs
When the unit enters a welding state, all sequence display modes are terminated and
the weld display mode is activated.
. For more information on Setting
If zero time is programmed for a timed sequence except for Weld, that sequence will
be skipped.
Sequence Parameters see Section 7-1.
• The Sequence push button allows the
selection of welding sequences. Five welding sequences are available. The default
sequence is the Weld sequence. The Weld
sequence is active on power up. Three
welding sequence LEDs are located above
the Sequence push button: Start, Crater,
and Preflow/Postflow. The applicable LED
illuminates to indicate which welding sequence is active.
• The LED illuminates to indicate that a welding sequence display mode other than Weld
is activate. Welding sequences other than
Weld must be set prior to initiating the arc.
OM-1500-9 Page 22
• In the weld sequence display mode the Sequence push button LED is Off. When the
Sequence push button is pressed, the Sequence push button flashes and the Start
LEDs flash. In this condition, the unit is in the
Start sequence display mode, and Start sequence parameters are shown in the displays.
• When the Sequence push button is pressed
a second time, the Crater sequence LED
flashes. The Sequence push button LED remains flashing. In this condition, the unit is
in the Crater sequence display mode, and
Crater sequence parameters are shown in
the displays.
• When the Sequence push button is pressed
a third time, the Preflow/Postflow sequence
LED flashes. The Sequence push button
LED remains flashing. In the Preflow display
mode the upper display shows the preflow
time and the lower display indicates the abbreviation PRE, to inform the operator that
preflow time is displayed. If the upper display push button is pressed, the Adjust control can be used to adjust preflow.
If the lower display push button is pressed, the
Adjust control can be used to select between
preflow PRE and postflow POST. When
POST is selected, the upper display can be
used to specify postflow time.
• When the Sequence push button is pressed
a fourth time, the unit returns to the welding
sequence display mode.
6-10. Auxiliary Menus
1
2
3
4
5
6
7
8
9
4
5
1
7
2
Program Display
Program Push Button
Sequence Push Button
Upper Display
Upper Display Push Button
Lower Display
Lower Display Push Button
Adjust Control
Setup Push Button
6
9
3
8
6-10 Auxiliary Menus (Continued)
Reset To Factory Settings
A reset menu is displayed if the following four
push buttons are pressed simultaneously:
Program, Sequence, upper display, and Setup. The upper display indicates “WIPE” . The
lower display indicates “OFF”. The lower push
button is active indicating that the Adjust control can be used to change the unit to “WIPE
ON”. When “WIPE ON” is set, if the original
four push buttons are simultaneously pressed
a second time, the unit will reset all settings to
factory default except the arc time and arc
cycle counts. If a reset is not desired, set the
display to “WIPE OFF” and simultaneously
press the Program, Sequence, upper display,
and Setup push buttons to exit the reset menu.
Auxiliary Menu
• An auxiliary menu is provided if both the Sequence and Setup push buttons are pressed
simultaneously. The Setup push button and
sequence push button LEDS flash when the
auxiliary menu is displayed.
Pushing the Setup push button will step
through the menu. Pushing the sequence
push button will step through the menu in reverse.
. The auxiliary menu may be exited at any
time by pressing both the Sequence push
button and the Setup push buttons simultaneously.
V-Min And V-Max
• If the Setup push button is pressed, the unit
allows the setting of the manual override
power source min and max voltage preset
range. The minimum voltage is displayed in
the upper display and the lower display indi-
cates “VMIN”. When the Setup push button
is pressed the unit displays the maximum
voltage setting of the welding power source.
The maximum voltage is displayed in the upper display and the lower display indicates
“VMAX”.
In both cases, the Adjust control is used to
specify the minimum and maximum voltage
settings of the welding power source. The settings correspond to arc voltage obtained at
minimum command and arc voltage obtained
at maximum command.
This method of setting “VMIN” and “VMAX”
may be used if the power source being used
is not listed in the Power Source Selection
Menu.
. If a default power source has already been
selected with the Power Source Selection
menu, setting “VMIN” and “VMAX” will
override the default power source settings.
. The power source selection menu must
be set to “OFF” when overriding the default “VMIN” or “VMAX” settings.
Arc time is indicated by the Program display
showing “HR”. Arc time is shown in the lower
display.
Cycles
• If the Setup push button is pressed, the unit
displays the number of cycles.
Arc cycles are indicated by the Program display showing “CL”. The arc cycle count is
shown in the lower display.
Run-In
• If the Setup button is pressed, the unit allows
setting the run-in modes. The run-in modes
are program specific. Each program may be
set to its own run-in mode.
The upper display indicates “RUNI”. The
lower display indicates “AUTO”, meaning the
factory set automatic run-in speed is selected.
Pressing the lower display button allows a
manual setting the run-in wire speed. Speed
may be adjusted from 10% to 100% of weld
wire speed.
Pressing the lower display button allows disabling of the run-in feature. When the lower
display indicates “OFF” run-in is disabled.
Power Source Selection Menu
Burnback
• If the Setup push button is pressed, the unit
allows the Power Source Selection menu to
be disabled or enabled.
• If the Setup push button is pressed, the unit
allows burnback time to be set.
The upper display shows “PSS”. Lower display shows “On” or “Off”. The Adjust Control is
used to select either “On” or “Off”.
Arc Time
• If the Setup push button is pressed, the unit
displays arc time in hours.
Burnback time and voltage can be specified
when the lower display indicates “BURN” and
the upper display indicates the burnback time
or voltage. The Adjust control is used to set the
desired burnback time or voltage. Burnback
settings, like run-in settings, are program specific. The active program is displayed in the
Program display and can be adjusted (see
Section 6-4).
OM-1500-9 Page 23
6-10 Auxiliary Menus (Continued)
Trigger Hold Setup
• If the Setup push button is pressed, the unit
allows trigger hold delay time to be set.
Trigger hold delay time is indicated by ”HOLD”
in the lower display and the hold delay time in
the upper display. The adjust control can be
used to specify a new delay time for trigger
hold. Trigger hold delay time is the minimum
amount of time the trigger must be held for trigger hold to work when the trigger is released
(the trigger hold function must be on). For example, if a trigger hold delay time of 2.0 seconds is defined, the operator must hold the
trigger for at least 2 seconds before releasing
it in order for the trigger hold function to work.
Once the trigger hold function is in effect, the
wire feeder will stay On until the trigger is
pressed and released again.
• There is an additional function built in called
”maximum trigger hold time” which is the
maximum length of time the trigger can be
held and the trigger hold function still work
when the trigger is released (the trigger hold
function must be on). The maximum trigger
hold time is set at 4.0 seconds after the trigger hold delay time. For example, if a trigger
hold delay time of 2.0 seconds is defined,
and the operator held the trigger in for more
than 6.0 seconds, the trigger hold function
would not be in effect and the wire feeder
would stop when the trigger is released.
operator to select programs during preflow by
clicking the trigger (pulling and releasing the
trigger in a maximum of 0.2 seconds). The
feeder will switch between any programs that
have a minimum of 0.2 seconds of preflow
time set in the weld sequence. Any combination of programs may be used. Trigger Program Select cannot be used while welding or
with Dual Schedule.
(Example: If programs 1 and 3 have a minimum of 0.2 seconds of preflow time, clicking
the trigger will toggle between programs 1 and
3).
Trigger Dual Schedule Select (DUAL) allows
the operator to switch between paired schedules (programs 1−2, 3−4, 5−6, or 7−8) with the
gun trigger, but only while welding. This feature cannot be used with Trigger Hold or Dual
Schedule. To end the weld, the trigger must be
released for 0.4 seconds.
(Example: when welding with this feature enabled in program 1, if you release, re-trigger,
and hold again within <0.4 seconds, the active
program will switch to program 2. If the previous sequence is repeated the active program will switch back to program 1. This cycle
can be repeated for the entire weld).
Process Select
• When the Setup push button is pressed
again, the menu repeats to the first menu
selection of run-in wire speed selection.
Process selection indicated by ”PROS” in the
upper display is set to either ”VOLT” or ”TRIM”
in the lower display. Each program can be selected be be a MIG program indicated by
”VOLT” or a pulsing program indicated by
”TRIM”.
Range Locks
Wire Feed Speed Units
Range locks are indicated by “LOCK” in the
upper display for wire speed or “LOCK” in the
lower display for voltage range. In a MIG program, the voltage range lock ranges from 0 to
10 volts. In a pulse program, the trim range
lock ranges from 0 to 100. The wire feed
speed range lock ranges from 0 to 250 ipm.
Locks are program dependent and wire speed
is independent from voltage or trim.
Wire feed speed setting indicated by “WFS” in
the upper display is set to “IPM” inches−per−
minute or ”MPM” meters−per−minute. This
setting is independent of the program selected.
Trigger Program Select
The upper display shows “OPT1”. Lower display shows “On” or “Off”. The Adjust Control
is used to select either “On” or “Off”.
• If the Setup push button is pressed, the unit
allows Trigger Program Select or Trigger
Dual Schedule to be enabled or disabled.
The upper display shows “TSEL”. Lower display shows “OFF” or “PROG” or “DUAL”. The
Adjust Control is used to select “OFF” or
“PROG” or “DUAL”.
Trigger Program Select (PROG) allows the
OM-1500-9 Page 24
OPT1
• If the Setup push button is pressed, the unit
allows OPT1 to be disabled or enabled.
“OPT1” is used by the Water Flow Shutdown
Option to stop the weld sequence if water flow
to a water cooled gun is interrupted. A closed
set of contacts between pins 1 and 2 of RC26
on Interface Board (PC20) will allow feeder to
operate normally. Opening the contacts will
stop the weld sequence and display “ERR” in
the upper display and “OPT1” in the lower display.
OPT2
• If the Setup push button is pressed, the unit
allows OPT2 to be disabled or enabled.
The upper display shows “OPT2”. Lower display shows “On” or “Off”. The Adjust Control
is used to select either “On” or “Off”.
“OPT2” is a second input that may be used
with an external device, such as a gas flow
switch, to end the weld sequence. The gas
flow switch may be used to stop the weld sequence if shielding gas flow to the gun is interrupted. A closed set of contacts between pins
1 and 2 of RC24 on Interface Board (PC20)
will allow feeder to operate normally. Opening
the contacts will stop the weld sequence and
display “ERR” in the upper display and
“OPT2” in the lower display.
Display Hold
Display hold indicated by ”DISP” in the upper
display is set to “OFF” or “HOLD” in the lower
display. When ”HOLD” is selected, the unit will
hold the last weld information for 5 seconds
following weld termination. If any front panel
push button is pressed, or if the Adjust control
is activated, the display hold feature is terminated.
Software Revision Level
• If the Setup push button is pressed, the unit
displays the software version being used by
the interface PCB (PC20).
• When the Setup button is pressed again, the
menu repeats.
Code
Upon leaving the auxiliary menu, the user is
asked if a password code indicated by
“CODE” in the top display should be activated.
By default the code is off, indicated by “OFF”
in the lower display. The user may enter a numerical password between 0 and 999 by turning the Adjust control. When the user re−enters the auxiliary menu, the password code
must be selected to gain access to the auxiliary menu. A failed attempt return the user to the
weld screen and a counter is incremented. A
counter in the program display shows the
number of incorrect attempts. The user has
five attempts to enter the correct password
code before being locked out of the auxiliary
menu, indicated by “LOCK” in the lower display . The power may be cycled to continue
welding but the user will remained locked out
of the auxiliary menu.
6-11. Jog/Purge
1
2
3
Adjust Control
Gun Trigger Receptacle
Jog/Purge Push Button
1
2
805 082-A
3
Pressing the Jog/Purge switch allows the operator to jog wire without energizing the weld
power or gas valve circuit.
• The unit provides the ability to jog the wire
feeder by means of the gun trigger or the
Jog/Purge switch. If the welding arc does
not initiate in 3 seconds after the gun trigger
is activated, the unit will perform a jog operation for a maximum of two minutes. If the gun
trigger is still activated after two minutes, the
jog operation is terminated to prevent complete despooling of the wire, in the case of
a damaged gun.
• The unit displays the “ERR TRIG“ message
to inform the operator that the trigger is activated.
• Jog speed can be adjusted by the Adjust
control when the unit is jogging wire. The
unit displays jog speed when the unit is being jogged.
• Jogging can also be accomplished by
pressing the Jog/Purge button.
• Pressing the Jog/Purge button also allows
the operator to purge gas lines before welding and to preset gas pressure at the
regulator.
6-12. Gouge (Optional)
1
2
Gun Trigger Receptacle
Gouge/Weld Switch
Push up to set control to Gouge.
Welding power source contactor
energizes, and gouge gas valve
GS2 is energized.
3
Gouge Control
Controls voltage while in the Gouge
mode.
4
Jog/Purge Button
1
2
3
4
257 339-B
OM-1500-9 Page 25
SECTION 7 − SETTING SEQUENCE PARAMETERS
7-1. Sequence Parameters In A Program
. For more information on
Sequence Push Button see
Section 6-9.
Sequence
If time is set to zero in Weld
sequence, welding continues until
gun trigger is released.
Parameters
Volts
IPM
1. Preflow
If time is set to zero in any timed
sequence except Weld, the
sequence is skipped.
Seconds
0-9.9
2. Run-In
X
3. Start
X
X
0.00-5.00
4. Weld
X
X
0-100.0
5. Crater
X
X
0-5.00
6. Burnback
X
0-0.25
7. Postflow
0-9.9
X = Setting available.
Weld Time
Crater
Time
Preflow
Time
Burnback
Time
Start
Time
Postflow
Time
Time
Burnback
Preflow
Trigger
Pressed
OM-1500-9 Page 26
Run-In Start
Weld
Crater
Trigger
Released
Postflow Sequence
End
SECTION 8 − SETTING DUAL SCHEDULE PARAMETERS
8-1. Optional Dual Schedule Switch Diagrams
1
1
1
DSS-9
2
2
1
DSS-8
2
Maint 2P (Maintained-Contact
2-Pole Switch)
Maint 1P (Maintained-Contact
1-Pole Switch)
2
1
2
TR
3
B
A
3
A
4
B
4
SECTION 9 − MAINTENANCE
9-1. Routine Maintenance
!
Disconnect power
before maintaining.
. Maintain more often
during severe conditions.
3 Months
Clean and
tighten
weld
terminals.
Replace
unreadable
labels.
Replace
cracked
parts.
Check
14-pin cord.
Repair or
replace
cracked
weld
cable.
Check gas
hose and
fittings.
Check gun
cable.
6 Months
Blow out or vacuum
inside. During heavy
service, clean
monthly.
Or
Clean
drive rolls.
OM-1500-9 Page 27
9-2. Diagnostics
1
2
3
4
3
Wrapper
Motor Control Board PC1
LED3
DIP Switch S1
. There
2
4
is a two-position DIP
switch S1 located on motor
control board PC1. These
switches are factory-set in the
off position and must remain in
that position for the unit to operate correctly.
1
. Front panel is shown removed for purpose of
illustration only. In actual use, front panel
would be in place.
The following error messages are shown on the
upper and lower displays to indicate specific errors.
Explanations are in the text below:
ERR
ERR
ERR
ERR
ERR
ERR
COM1
TRG1
TCH1
MTR1
OPT1
OPT2
Indicates a
communication
error.
Indicates a trigger
error.
Indicates a
tachometer error.
Indicates a motor
error.
No gas flow
detected.
Optional error
condition.
Ref. 805 084-B
LED3-Related Error Indications
Error conditions are indicated by LED3 on
PC1. To view LED3, turn Off unit, remove
wrapper, and turn unit On. LED3 is most easily
observed from the left side of the unit.
The LED blinks in a 2.5 second cycle. The
number of blinks in this period indicates the
type of error.
The priority of the errors is related to the number of blinks indicating the error. The more
blinks, the more severe the error (motor error
is top priority). A higher priority error overrides
a lower one (if a motor error and a communication error existed, the light would blink four
times for the motor error).
Since blink On time and blink Off time are
equal in a four-blink cycle, the four−blink sequence appears as a constant blink.
1 blink = Communication Error
2 blinks = Trigger Error
3 blinks = Tach Error
OM-1500-9 Page 28
4 blinks = Motor Error
ERR COM1
speed is regulated through the monitoring of
voltage and current.
• The communication error occurs 2.5 seconds after a loss of communication between
the motor and front panel boards. The user
may continue to weld with this error. The error may be cleared by resetting the unit (see
Section 6-10).
ERR MTR1
ERR TRG1
ERR OPT1
• The trigger error occurs if the user has the
trigger held for more than two minutes without striking an arc, or if the user holds the
trigger past the postflow phase in a timed
weld. This error also occurs if the trigger is
held when the feeder is powered up. The error may be cleared by releasing the trigger.
• The optional 1 error indicates no coolant
flow in water flow switch option. The error
may be reset by reestablishing coolant flow
to the gun, and then pressing any button on
front panel.
ERR TCH1
• The tach error occurs 2 seconds after the
loss of tachometer feedback. The user may
continue to weld with this error. The motor
• The motor error indicates that the motor
has been drawing too much current for too
long. To remedy this, reduce the wire feed
speed or the wire feeder torque load/duty
cycle.
ERR OPT2
• The optional 2 error indicates a problem
with optional device connected to RC24 on
Interface Board (PC20). The error may be
reset by correcting the problem, and then
pressing any button on front panel.
SECTION 10 − ELECTRICAL DIAGRAM
Figure 10-1. Circuit Diagram
235 601-C
OM-1500-9 Page 29
SECTION 11 − PARTS LIST
. Hardware is common and
not available unless listed.
6
7
5
8
9
10
11
12
11
10
9
14
13
16
17
18
4 Fig. 11-3
15
3
19
2
1
20
21
22 Fig. 11-2
805 083-B
Figure 11-1. Main Assembly
OM-1500-9 Page 30
Item
No.
Part
No.
Description
Quantity
Figure 11-1. Main Assembly
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
. . . . . . . . . . . . . . . 159647
. . . . . . . . . . . . . . . 159646
. . . . . . . . . . . . . . . 159360
. . . . . . . . . . . . Figure 11-4
. . . . . . . . . . . . . . . 141753
. . . . . . . . . . . . . . . 058427
. . . . . . . . . . . . . . . 180571
. . . . . . . . . . . . . . . 010233
. . . . . . . . . . . . . . . 057971
. . . . . . . . . . . . . . . 010191
. . . . . . . . . . . . . . . 058628
. . . . . . . . . . . . . . . 058428
. . . . . . . . . . . . . . . 248974
. . . . . . . . . . . . . . . 135205
. . . . . . . . . . . . . . . 200556
. . . . . . . . . . . . . . . 201781
. . . . . . . . . . . . . . . 156243
. . . . . . . . . . . . . . . 145639
. . . . . . . . . . . . . . . 200552
. . . . . . . . . . . . . . . 134306
. . . . . . . . . . . . . . . 200557
. . . . . . . . . . . . Figure 11-2
. . Insulator, Motor Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Clamp, Motor Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Insulator, Screw Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Drive Assembly, Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Hub & Spindle Assembly, (Consisting Of) . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Ring, Retaining Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Shaft, Support Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Spring, Cprsn .970 Od X .120 Wire X 1.250Pld . . . . . . . . . . . . . . . . . . .
. . . . Washer, Flat Stl Keyed 1.500Dia X .125Thk . . . . . . . . . . . . . . . . . . . . .
. . . . Washer, Fbr .656 Id X 1.500 Od X .125Thk . . . . . . . . . . . . . . . . . . . . . .
. . . . Washer, Brake Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Hub, Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Tubing, Stl .875 Od X12Ga Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Nut, Stl Slflkg Hex Reg .625-11 W/Nylon Insert . . . . . . . . . . . . . . . . . . .
. . Support, Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Knob, W/Extension Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Clamp, Motor Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Strip, Buna N Compressed Sheet .062 X 4.000 X 4.000 . . . . . . . . . . . . .
. . Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Foot, Rubber 1.250 Dia X 1.375 High No 10 Screw . . . . . . . . . . . . . . . . .
. . Stiffener, Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
4
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
4
1
1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500-9 Page 31
. Hardware is common and
not available unless listed.
8
10
9
1
4
12
11
13
10
9
3
7
6
2
14
15
23
16
5
22
17
21
18
19
20
805 084-B
Figure 11-2. Control Box
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Figure 11-2. Control Box (Figure 11-1 Item 21)
. . . 1 . . . . . . . . . . . . . . . 238514
. . . 2 . . . . . . . . . . . . . . . 200153
. . . 3 . . . . PC21 . . . . . 227879
. . . 4 . . . . PC20 . . . . . 235331
. . . 5 . . . . . S1 . . . . . . . 111997
. . . 6 . . . . . . . . . . . . . . . 010494
. . . 7 . . . . . . . . . . . . . . . 235206
. . . 8 . . . . . . . . . . . . . . . 232880
. . . . . . . . . . . . . . . . . . . . . 204910
. . . 9 . . . . . . . . . . . . . . . 139041
. . . 10 . . . . . . . . . . . . . . . 163519
. . . 11 . . . . . . . . . . . . . . . 079739
. . . 12 . . . PLG12 . . . . . 141162
. . . . . . . . . PLG30 . . . . . 115091
. . . . . . . . . PLG32 . . . . 202592
. . . 13 . . . . . . . . . . . . . . . 241416
. . . 14 . . . . . . . . . . . . . . . 134201
. . . 15 . . . . . . . . . . . . . . . 000527
. . . 16 . . . . . . . . . . . . . . . . 211989
. . . 17 . . . . . . . . . . . . . . . 605227
. . . 18 . . . . GS1 . . . . . 228035
. . . 19 . . . . PC1 . . . . . 238469
OM-1500-9 Page 32
. . Wrapper, Feeder W/Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Overlay, Upper Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Circuit Card Assy, Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Circuit Card Assy, Display/Micro W/Program . . . . . . . . . . . . . . . . . . . . . . . 1
. . Switch, Rocker Spst 10A 250 VAC On-Off . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bushing, Snap-In Nyl 1.375 Id X 1.750 Mtg Hole . . . . . . . . . . . . . . . . . . . 2
. . Enclosure, Control/Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Circuit Card Assy, 14 Pin Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Cable, Power (Consisting Of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Strain Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Cable, Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5 Ft
. . . . Conn, Circ Cpc Clamp Str Rlf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Housing Plug+Pins, (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Housing Plug+Skts, (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Housing Plug+Skts, (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Blank, Snap-In Nyl 1.187 Mtg Hole Black . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Stand-Off Support, PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . Blank, Snap-In Nyl .875 Mtg Hole Black . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Fitting, W/Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Nut, 750-14 Knurled1.68Dia .41H Nyl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Valve, 34VDC 1Way .750−14 Thd 2mm Orf 100PSI . . . . . . . . . . . . . . . . 1
. . Circuit Card Assy, Motor Control W/Program . . . . . . . . . . . . . . . . . . . . . . 1
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Figure 11-2. Control Box (Figure 11-1 Item 21) (Continued)
. . . 20 . . . . . S2 . . . . . . 200295 . .
. . . 21 . . . . . . . . . . . . . . . 213134 . .
. . . 22 . . . . RC13 . . . . . 237667 . .
. . . 23 . . . . . . . . . . . . . . . 235209 . .
................................
. . . . . . . . . . PLG6 . . . . . . 115094 . .
. . . . . . . . PLG11,61 . . . 131055 . .
. . . . . . . . . . PLG1 . . . . . 202592 . .
. . . . . . . . . . PLG4 . . . . . 136810 . .
. . . . . . . . PLG7,27 . . . . 115091 . .
. . . . . . . . . PLG10 . . . . 130203 . .
. . . . . . . . . . . . . . . . . . . . . 238487 . .
Switch, Rocker Spdt 15A 12V (On)-Off-(On) . . . . . . . . . . . . . . . . . . . . . . .
Knob, Encoder 1.670 Dia X .250 Id Push On W/Spring . . . . . . . . . . . . . .
Circuit Card Assy, Trigger Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Panel, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nameplate (Order By Model And Serial Number) . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (Service Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Label, Warning General Precautionary CE/Domestic . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
1
1
1
1
Notes
OM-1500-9 Page 33
. Hardware is common and
not available unless listed.
6
7
8
9
10
5
11
12
4
2
4
3
16
3
11
1
13
2
1
15
14
View is backside
of front panel
256 396-C
Figure 11-3. Front Panel Assembly With Gouge Option
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Figure 11-3. Front Panel Assembly With Gouge Option
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
. . . . . S2 . . . . . . 200295 . .
. . . . R90 . . . . . 073562 . .
. . . . . S90 . . . . . . 011622 . .
. . . . PC51 . . . . . 237667 . .
. . . . . . . . . . . . . . . 072785 . .
. . . . PC20 . . . . . 235331 . .
. . . . PC21 . . . . . 238273 . .
. . . . . . . . . . . . . . . 204762 . .
. . . . . . . . . . . . . . . 256397 . .
. . . . . . . . . . . . . . . . 114045 . .
. . . . . . . . . . . . . . . 604645 . .
. . . . . . . . . . . . . . . 193920 . .
. . . . . . . . . . . . . . . 189404 . .
..........................
. . . . . . . . . . . . . . . 605321 . .
. . . . . . . . . . . . . . . 193920 . .
OM-1500-9 Page 34
Switch, Rocker Spdt 15A 12V (On)−Off−(On) . . . . . . . . . . . . . . . . . . . . . .
Pot, Cp Std Slot 1T 2. W 10K Linear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch, Tgl 3Pdt 15A 125VAC On−None−On Spd Term . . . . . . . . . . . . .
Circuit Card Assy, Trigger Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screw, 006−32X .37 Hexwhd−Pln Stl Pld Slffmg Tap−Rw . . . . . . . . . . . .
Circuit Card Assy, Display/Micro W/Program . . . . . . . . . . . . . . . . . . . . . . .
Circuit Card Assy, Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overlay, Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Panel, Front W/Gouge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screw, 006−32X .50 Hexwhd−Pln Stl Pld Slffmg Tap−Rw . . . . . . . . . . . .
Nut, 375−32 .56Hex .09H Stl Pld Use W/Pots . . . . . . . . . . . . . . . . . . . . . .
Knob, Pointer .840 Dia X .250 Id W/One Set Screw . . . . . . . . . . . . . . . . .
Spacer, Nylon .718 Od X .526 Id X .281 Lg . . . . . . . . . . . . . . . . . . . . . . . .
Nameplate, Lower W/Gouge (Order by Model and Serial Number) . . . .
Nut, 468−32 .56Hex .09H Brs Blk Use W/Switches . . . . . . . . . . . . . . . . .
Knob, Pointer .840 Dia X .250 Id W/One Set Screw . . . . . . . . . . . . . . . . .
1
1
1
1
4
1
1
1
1
4
2
1
1
1
1
1
Notes
OM-1500-9 Page 35
. Hardware is common and
13
19
not available unless listed.
11
14
15
See Table 11-1 For
Drive Roll & Wire Guide Kits
16
17
18
9
1
2
3
4
5
8
7
6
19
20
12
10
11
21
22
27
24
25
28
29
23
26
36
30
31 32
6
37
34
5
33
4
3
35
2
1
803 790-C
Figure 11-4. Drive Assembly, Wire
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Figure 11-4. Drive Assembly, Wire (Figure 11-1 Item 4)
... 1 ...............
... 2 ...............
... 3 ...............
... 4 ...............
... 5 ...............
... 6 ...............
... 7 ...............
... 8 ...............
. . . 9 . . . . M1 . . . . . .
. . . 9 . . . . M1 . . . . . .
. . . 9 . . . . M1 . . . . . .
.....................
.....................
.....................
.....................
. . . 10 . . . . . . . . . . . . . . .
.....................
.....................
.....................
.....................
.....................
.....................
. . . 11 . . . . . . . . . . . . . . .
. . . 12 . . . . . . . . . . . . . . .
. . . 13 . . . . . . . . . . . . . . .
. . . 14 . . . . . . . . . . . . . . .
OM-1500-9 Page 36
010668
172075
149962
149486
132750
150520
133493
133350
201230
201231
209131
153491
153492
*153493
184136
155098
153550
155099
155100
154031
133493
203631
203641
182415
203640
182156
. . Screw, Cap Stl Sch .250-20 X 1.500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Carrier, Drive Roll W/Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spacer, Carrier Drive Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pin, Rotation Arm Rocker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Arm, Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Spacer, Flat Stl .257 Id X .619 Od X .105 . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Ring, Retaining Ext .250 Shaft X .025Thk . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pin, Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Motor, Gear 1/8HP 24VDC Standard Speed . . . . . . . . . . . . . . . . . . . . . . . .
. . Motor, Gear 1/8HP 24VDC High Speed (Optional) . . . . . . . . . . . . . . . . . . .
. . Motor, Gear 1/8HP 24VDC Low Speed (Optional) . . . . . . . . . . . . . . . . . . .
. . . . Kit, Brush Replacement (Consisting Of) . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . Cap, Brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . Brush, Carbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Kit, Brush Holder Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Kit, Cover Motor Gearbox (Consisting Of) . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Cover, Motor Gearbox (Consisting Of) . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . Gasket, Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . Screw, Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Spacer, Locating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Ring, Rtng Ext .250 Shaft Grv X .025Thk . . . . . . . . . . . . . . . . . . . . . . . . .
. . Pressure Arm, S/L & Vert S/R 4 Roll (Consisting Of) . . . . . . . . . . . . . . . . .
. . . . Washer, Flat Indicator Spring Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Pin, Cotter Hair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Knob, W/Extension Short Pressure Arm . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . Spring, Cprsn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
4
2
2
2
2
1
1
1
1
1
2
2
1
1
1
1
5
2
1
1
2
1
1
2
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Figure 11-4. Drive Assembly, Wire (Figure 11-1 Item 4) (continued)
. . . 15 . . . . . . . . . . . . . . . 182155
. . . 16 . . . . . . . . . . . . . . . 132746
. . . 17 . . . . . . . . . . . . . . . 203633
. . . 18 . . . . . . . . . . . . . . . 203632
. . . 19 . . . . . . . . . . . . . . . 133739
. . . 20 . . . . . . . . . . . . . . . 203637
. . . 21 . . . PC51 . . . . . 237048
. . . . . . . . . PLG5 . . . . . 131204
. . . . . . . . . . . . . . . . . . . . . . 604311
. . . 22 . . . . . . . . . . . . . . . . 132611
. . . . . . . . . . . . . . . . . . . . . . 603115
. . . 23 . . . . . . . . . . . . . . . 167387
. . . 24 . . . . . . . . . . . . . . . 168825
. . . 25 . . . . . . . . . . . . . . . 133308
. . . 26 . . . . . . . . . . . . . . . 134834
. . . 27 . . . . . . . . . . . . . . . 244579
. . . 28 . . . . . . . . . . . . . . . 601966
. . . 29 . . . . . . . . . . . . . . . 149959
. . . 30 . . . . . . . . . . . . . . . 167788
. . . 31 . . . . . . . . . . . . . . . 185624
. . . 32 . . . . . . . . . . . . . . . 242259
. . . 33 . . . . . . . . . . . . . . . 242261
. . . 34 . . . . . . . . . . . . . . . 231232
. . . 35 . . . . . . . . . . . . . . . 151437
. . . 36 . . . . . . . . . . . . . . . 179277
. . . . . . . . . . . . . . . . . . . . . 196956
. . . 37 . . . . . . . . . . . . . . . 108940
. . . . Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . Bushing, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . Shaft, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Carrier, Shaft Dual Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Washer, Flat Buna .375 Id X .625 Od X .062Thk . . . . . . . . . . . . . . . . . . . 2
. . . . Knob, W/Extension Long Pressure Arm . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Circuit Card, Digital Tach (Consisting Of) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Grommet, Rbr .250 Id X .375Mtg Hole .062 Groove . . . . . . . . . . . . . . . . 1
. . Optical Encoder Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Weather Stripping, Adh .125 X .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Spacer, Locating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . Drive, Pinion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Ring, Retaining Ext .375 Shaft X .025Thk . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Hose, Sae .187 Id X .410 Od (Order By Ft) . . . . . . . . . . . . . . . . . . . . . . . . 2Ft
. . Adapter Assy, Gun/Feeder Lh Accu−Mate (Consisting Of) . . . . . . . . . . . . 1
. . . . Screw, Cap Stl Hexhd .375-16 X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Fitting, Brs Barbed M 3/16Tbg X .312-24 . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Nut, 375−16 .56Hex .34H Stl Pld Sem Cone Wshr.88D . . . . . . . . . . . . . 1
. . . . Screw, 010−32X .50 Hexwhd.40D Stl Pld Slffmg Trilob . . . . . . . . . . . . . 2
. . . . Clamp, Power Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Lock, Power Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Washer, Flat .344idx0.688odx.065t Stl Pld Ansi.312 . . . . . . . . . . . . . . . . 1
. . . . Knob, Plstc T 1.125 Lg X .312-18 X 1.500 . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Cover, Drive Roll (Consisting Of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Label, Warning Electric Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Screw, Cap Stl Hexhd .250-20 X .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
*Recommended Spare Parts.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500-9 Page 37
Table 11-1. Drive Roll And Wire Guide Kits
OM-1500-9 Page 38
Inlet Guide
221030
221030
221030
229919
229919
Wire Sizes
.023 to .040 in. (0.6 to 1.0mm)
.045 to .052 in. (1.1 to 1.4mm)
1/16 to 5/64 in. (1.6 to 2mm)
3/32 to 7/64 in. (2.4 to 2.8mm)
1/8 in. (3.2mm)
Wire Guides
*Accommodates .045 and .047 (3/64 in) wire
**Requires a low *speed wire feeder
149522
149521
149520
149519
149518
Intermediate Guide
151042
151043**
151076**
151075
151074
151073
151072
151071
151070
”U” COGGED FOR
EXTREMELY SOFT
WIRE OR SOFT*
SHELLED CORED
WIRES
1/16 in. (1.6mm)
.047 in. (1.2mm)
.035 in. (0.9mm)
Wire Size
221912
221912
221912
Inlet Guide
Nylon Wire Guides for Feeding Aluminum Wire
151060**
151059
151058
1/8 in. (3.2 mm)
151055
7/64 in. (2.8 mm)
151039
151054
151053
151041
151029
1/16 in. (1.6 mm)
151038
151037*
3/32 in. (2.4 mm)
151028
.052 in. (1.3/1.4 mm)
151057
151027
.045 in. (1.1/1.2 mm)
151056
161190
.040 in. (1.0 mm)
151052
151040
151026
.035 in. (0.9 mm)
”V” KNURLED FOR
HARD*SHELLED
CORED WIRES
5/64 in. (2.0 mm)
151025
.030 in. (0.8 mm)
”U” GROOVE FOR
SOFT*SHELLED
CORED WIRES
.068/.072 in. (1.8 mm)
151024
.023/.025 in. (0.6 mm)
WIRE SIZE
”V” GROOVE FOR
HARD WIRE
205937
205936
242417
Intermediate Guide
265257
265256*
265255
POLISHED
”U” GROOVE FOR
ALUMINUM WIRES
CONTAINS NYLON
WIRE GUIDES
Effective January 1, 2016
(Equipment with a serial number preface of MG or newer)
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions below, 5. 6 Months — Parts
Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to its original
* Batteries
retail purchaser that new Miller equipment sold after the effective
* Bernard Guns (No Labor)
date of this limited warranty is free of defects in material and
* Tregaskiss Guns (No Labor)
workmanship at the time it is shipped by Miller. THIS WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS 6. 90 Days — Parts
* Accessory (Kits)
OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
* Canvas Covers
* Induction Heating Coils and Blankets, Cables, and
Within the warranty periods listed below, Miller will repair or replace
Non-Electronic Controls
any warranted parts or components that fail due to such defects in
* M-Guns
material or workmanship. Miller must be notified in writing within
thirty (30) days of such defect or failure, at which time Miller will
* MIG Guns and Subarc (SAW) Torches
provide instructions on the warranty claim procedures to be
* Remote Controls and RFCS-RJ45
followed. If notification is submitted as an online warranty claim, the
* Replacement Parts (No labor)
claim must include a detailed description of the fault and the
* Roughneck Guns
troubleshooting steps taken to identify failed components and the
* Spoolmate Spoolguns
cause of their failure.
Miller shall honor warranty claims on warranted equipment listed
below in the event of such a failure within the warranty time periods.
All warranty time periods start on the delivery date of the equipment
to the original end-user purchaser, and not to exceed twelve months
after the equipment is shipped to a North American distributor or
eighteen months after the equipment is shipped to an International
distributor.
1.
2.
3.
4.
5 Years Parts — 3 Years Labor
* Original Main Power Rectifiers Only to Include SCRs,
Diodes, and Discrete Rectifier Modules
3 Years — Parts and Labor
* Auto-Darkening Helmet Lenses (Except Classic
Series) (No Labor)
* Engine Driven Welder/Generators
(NOTE: Engines are Warranted Separately by the
Engine Manufacturer.)
* Inverter Power Sources (Unless Otherwise Stated)
* Plasma Arc Cutting Power Sources
* Process Controllers
* Semi-Automatic and Automatic Wire Feeders
* Transformer/Rectifier Power Sources
2 Years — Parts and Labor
* Auto-Darkening Helmet Lenses − Classic Series Only
(No Labor)
* Fume Extractors − Capture 5, Filtair 400 and Industrial
Collector Series
1 Year — Parts and Labor Unless Specified
* Automatic Motion Devices
* CoolBelt and CoolBand Blower Unit (No Labor)
* Desiccant Air Dryer System
* External Monitoring Equipment and Sensors
* Field Options
(NOTE: Field options are covered for the remaining
warranty period of the product they are installed in,
or for a minimum of one year — whichever is
greater.)
* RFCS Foot Controls (Except RFCS-RJ45)
* Fume Extractors − Filtair 130, MWX and SWX Series
* HF Units
* ICE/XT Plasma Cutting Torches (No Labor)
* Induction Heating Power Sources, Coolers
(NOTE: Digital Recorders are Warranted Separately
by the Manufacturer.)
* LiveArc Welding Performance Management System
* Load Banks
* Motor-Driven Guns (except Spoolmate Spoolguns)
* PAPR Blower Unit (No Labor)
* Positioners and Controllers
* Racks
* Running Gear/Trailers
* Spot Welders
* Subarc Wire Drive Assemblies
* Water Coolant Systems
* TIG Torches (No Labor)
* Wireless Remote Foot/Hand Controls and Receivers
* Work Stations/Weld Tables (No Labor)
Miller’s True Blue® Limited Warranty shall not apply to:
1.
2.
3.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, relays, work
station table tops and welding curtains, or parts that
fail due to normal wear. (Exception: brushes and
relays are covered on all engine-driven products.)
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable
and necessary maintenance, or equipment which has
been used for operation outside of the specifications for
the equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in appropriate
cases, (3) the reasonable cost of repair or replacement at an
authorized Miller service station; or (4) payment of or credit for the
purchase price (less reasonable depreciation based upon actual
use) upon return of the goods at customer’s risk and expense.
Miller’s option of repair or replacement will be F.O.B., Factory at
Appleton, Wisconsin, or F.O.B. at a Miller authorized service facility
as determined by Miller. Therefore no compensation or
reimbursement for transportation costs of any kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT),
WHETHER BASED ON CONTRACT, TORT OR ANY OTHER
LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY
IMPLIED WARRANTY, GUARANTY OR REPRESENTATION AS
TO PERFORMANCE, AND ANY REMEDY FOR BREACH OF
CONTRACT TORT OR ANY OTHER LEGAL THEORY WHICH,
BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION,
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF
DEALING, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT
FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED BY
MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein, and to
the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available, but
may vary from province to province.
miller_warr 2016-01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
For International Locations Visit
www.MillerWelds.com
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
ORIGINAL INSTRUCTIONS − PRINTED IN USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
© 2016 Miller Electric Mfg. Co.
2016−01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising