Miller SPECTRUM 375 X-TREME AND XT30 TORCH Owner's Manual

OM-253555D
2016−12
Processes
Air Plasma Cutting
Description
Air Plasma Cutter
R
Spectrum 375 X-TREME
And XT30 Torch
For product information,
Owner’s Manual translations,
and more, visit
www.MillerWelds.com
File: Plasma Cutters
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001 Quality System Warranty and service information for your
Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual specification sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 2009−09
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Plasma Arc Cutting Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Signification des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers liés au coupage à l’arc au plasma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance . . . . .
2-4. Proposition californienne 65 Avertissements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6. Informations relatives aux CEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Additional Safety Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Miscellaneous Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Serial Number And Rating Label Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Torch Dimensions And Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Power Source Dimensions And Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Selecting A Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Connecting Gas/Air Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Connecting And Disconnecting Work Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Connecting Work Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Electrical Service Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6. Extension Cord Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Multi−Voltage Plug (MVP) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8. Connecting 120 Volt Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-9. Connecting 1-Phase Input Power For 240 VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Cutting Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. Trigger Safety Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4. Plasma Cutting System Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-5. Sequence Of Cutting Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-6. Sequence Of Piercing Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − MAINTENANCE & TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3. Wrapper Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4. Checking Shield Cup Shutdown System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5. Checking Or Replacing Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-6. Checking/Replacing Retaining Cup, Tip, And Electrode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-7. Status/Trouble Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-8. Troubleshooting Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-9. Troubleshooting Torch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY
1
1
1
3
4
4
4
5
5
5
7
9
9
9
11
11
11
12
12
12
13
14
14
14
15
15
15
16
16
17
17
18
19
20
22
22
23
24
24
25
26
27
27
27
28
28
28
29
30
31
31
32
34
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
pom_2015−09
Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.
1-1. Symbol Usage
DANGER! − Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in the text.
NOTICE − Indicates statements not related to personal injury.
. Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the
hazards.
1-2. Plasma Arc Cutting Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information
found in the Safety Standards listed in Section 1-5. Read and
follow all Safety Standards.
Only qualified persons should install, operate, maintain, and
repair this unit.
During operation, keep everybody, especially children, away.
CUTTING can cause fire or explosion.
Hot metal and sparks blow out from the cutting arc.
The flying sparks and hot metal, hot workpiece, and
hot equipment can cause fires and burns. Check
and be sure the area is safe before doing any cutting.
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
Remove all flammables within 35 ft (10.7 m) of the cutting arc. If this
is not possible, tightly cover them with approved covers.
Do not cut where flying sparks can strike flammable material.
Protect yourself and others from flying sparks and hot metal.
Be alert that sparks and hot materials from cutting can easily go
through small cracks and openings to adjacent areas.
Watch for fire, and keep a fire extinguisher nearby.
Be aware that cutting on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
Do not cut on containers that have held combustibles, or on closed
containers such as tanks, drums, or pipes unless they are properly
prepared according to AWS F4.1 and AWS A6.0 (see Safety Standards).
Connect work cable to the work as close to the cutting area as practical to prevent cutting current from traveling long, possibly unknown
paths and causing electric shock, sparks, and fire hazards.
Do not use plasma cutter to thaw frozen pipes.
Never cut containers with potentially flammable materials inside −
they must be emptied and properly cleaned first.
Do not cut where the atmosphere can contain flammable dust, gas,
or liquid vapors (such as gasoline).
Do not cut pressurized cylinders, pipes, or vessels.
Wear body protection made from durable, flame−resistant material
(leather, heavy cotton, wool). Body protection includes oil-free
clothing such as leather gloves, heavy shirt, cuffless trousers, high
shoes, and a cap.
Do not locate unit on or over combustible surfaces.
Remove any combustibles, such as a butane lighter or matches,
from your person before doing any cutting.
After completion of work, inspect area to ensure it is free of sparks,
glowing embers, and flames.
Use only correct fuses or circuit breakers. Do not oversize or bypass them.
Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
for hot work and have a fire watcher and extinguisher nearby.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The torch and work circuit are
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. Plasma arc cutting requires
higher voltages than welding to start and maintain the arc (200 to 400
volts dc are common), but can also use torches designed with safety
interlock systems which turn off the machine when the shield cup is
loosened or if tip touches electrode inside the nozzle. Incorrectly
installed or improperly grounded equipment is a hazard.
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
Do not touch live electrical parts.
Wear dry, hole-free insulating gloves and body protection.
Insulate yourself from work and ground using dry insulating mats or
covers big enough to prevent any physical contact with the work or
ground.
Do not touch torch parts if in contact with the work or ground.
Turn off power before checking, cleaning, or changing torch parts.
Disconnect input power before installing or servicing this equipment. Lockout/tagout input power according to OSHA CFR
1910.147 (see Safety Standards).
Properly install, ground, and operate this equipment according to its
Owner’s Manual and national, state, and local codes.
Check and be sure that input power cord ground wire is properly
connected to ground terminal in disconnect box or that cord plug is
connected to a properly grounded receptacle outlet − always verify
the supply ground.
When making input connections, attach proper grounding conductor first.
Keep cords dry, free of oil and grease, and protected from hot metal
and sparks.
Frequently inspect input power cord and ground conductor for damage or bare wiring – replace immediately if damaged – bare wiring
can kill.
Turn off all equipment when not in use.
Do not use worn, damaged, undersized, or repaired cables.
Do not wrap torch cable around your body.
Ground the workpiece to a good electrical (earth) ground if required
by codes.
Use only well-maintained equipment. Repair or replace damaged
parts at once.
Wear a safety harness if working above floor level.
Keep all panels and covers securely in place.
Do not bypass or try to defeat the safety interlock systems.
Use only torch(es) specified in Owner’s Manual.
Keep away from torch tip and pilot arc when trigger is pressed.
Clamp work cable with good metal-to-metal contact to workpiece
(not piece that will fall away) or worktable as near the cut as
practical.
Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
OM-253555 Page 1
ELECTRIC SHOCK can kill.
FUMES AND GASES can be hazardous.
SIGNIFICANT DC VOLTAGE exists in
inverter power sources AFTER the removal of input power.
Cutting produces fumes and gases. Breathing
these fumes and gases can be hazardous to
your health.
D Turn Off unit, disconnect input power, check voltage on input capacitors, and be sure it is near zero (0) volts before touching any
parts. Check capacitors according to instructions in Maintenance
Section of Owner’s Manual or Technical Manual before touching
any parts.
D
D
D
D
EXPLODING PARTS can injure.
D On inverter power sources, failed parts can explode or cause other parts to explode when
power is applied. Always wear a face shield
and long sleeves when servicing inverters.
FLYING SPARKS can injure.
D
D
D
Sparks and hot metal blow out from the cutting arc.
Chipping and grinding cause flying metal.
D
D
D
Wear approved face shield or safety goggles with side shields.
Wear proper body protection to protect skin.
Wear flame-resistant ear plugs or ear muffs to prevent sparks from
entering ears.
D
PLASMA ARC can injure.
ARC RAYS can burn eyes and skin.
Arc rays from the cutting process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin.
D
D
D
D
Wear face protection (helmet or shield) with a proper shade of filter
lenses to protect your face and eyes from arc rays and sparks when
cutting or watching. ANSI Z49.1 (see Safety Standards) suggests a
No. 9 shade (with No. 8 as minimum) for all cutting currents less
than 300 amperes. Z49.1 adds that lighter filter shades can be used
when the arc is hidden by the workpiece. As this is normally the case
with low current cutting, the shades suggested in Table 1 are provided for the operator’s convenience.
Wear approved safety glasses with side shields under your helmet
or shield.
Use protective screens or barriers to protect others from flash, glare
and sparks; warn others not to watch the arc.
Wear body protection made from durable, flame−resistant material
(leather, heavy cotton, wool). Body protection includes oil-free
clothing such as leather gloves, heavy shirt, cuffless trousers, high
shoes, and a cap.
Table 1. Eye Protection For Plasma Arc Cutting
Current Level In Amperes
Below 20
20 − 40
40 − 60
60 − 100
D
D
Minimum Shade Number
#4
#5
#6
#8
D
D
D
D
D
D
D
D
D
D
D
D
D
D
Prolonged noise from some cutting applications can
damage hearing if levels exceed limits specified by
OSHA (see Safety Standards).
D
OM-253555 Page 2
The heat from the plasma arc can cause serious
burns. The force of the arc adds greatly to the burn
hazard. The intensely hot and powerful arc can
quickly cut through gloves and tissue.
Keep away from the torch tip.
Do not grip material near the cutting path.
The pilot arc can cause burns − keep away from torch tip when trigger is pressed.
Wear body protection made from durable, flame−resistant material
(leather, heavy cotton, wool). Body protection includes oil-free
clothing such as leather gloves, heavy shirt, cuffless trousers, high
shoes, and a cap.
Point torch away from your body and toward work when pressing
the torch trigger − pilot arc comes on immediately.
Turn off power source and disconnect input power before disassembling torch or changing torch parts.
Use only torch(es) specified in the Owner’s Manual.
CYLINDERS can explode if damaged.
NOISE can damage hearing.
Use approved ear plugs or ear muffs if noise level is high.
Warn others nearby about noise hazard.
Keep your head out of the fumes. Do not breathe the fumes.
If inside, ventilate the area and/or use local forced ventilation at the
arc to remove cutting fumes and gases. The recommended way to
determine adequate ventilation is to sample for the composition and
quantity of fumes and gases to which personnel are exposed.
If ventilation is poor, wear an approved air-supplied respirator.
Read and understand the Safety Data Sheets (SDSs) and the manufacturer’s instructions for adhesives, coatings, cleaners,
consumables, coolants, degreasers, fluxes, and metals.
Work in a confined space only if it is well ventilated, or while wearing
an air-supplied respirator. Fumes from cutting and oxygen depletion
can alter air quality causing injury or death. Be sure the breathing air
is safe.
Do not cut in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
Do not cut on coated metals, such as galvanized, lead, or cadmium
plated steel, unless the coating is removed from the cutting area, the
area is well ventilated, and while wearing an air-supplied respirator.
The coatings and any metals containing these elements can give off
toxic fumes when cut.
Do not cut containers with toxic or reactive materials inside or
containers that have held toxic or reactive materials − they must be
emptied and properly cleaned first.
D
D
Compressed gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of metalworking processes, be sure to treat them carefully.
Protect compressed gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open flame, sparks, and arcs.
Install and secure cylinders in an upright position by chaining them
to a stationary support or equipment cylinder rack to prevent falling
or tipping.
Keep cylinders away from any cutting or other electrical circuits.
Never allow electrical contact between a plasma arc torch and a
cylinder.
Never cut on a pressurized cylinder − explosion will result.
Use only correct compressed gas cylinders, regulators, hoses, and
fittings designed for the specific application; maintain them and associated parts in good condition.
Turn face away from valve outlet when opening cylinder valve. Do
not stand in front of or behind the regulator when opening the valve.
Keep protective cap in place over valve except when cylinder is in
use or connected for use.
Use the right equipment, correct procedures, and sufficient number
of persons to lift and move cylinders.
Read and follow instructions on compressed gas cylinders, associated equipment, and Compressed Gas Association (CGA)
publication P-1 listed in Safety Standards.
1-3. Additional Symbols For Installation, Operation, And Maintenance
FALLING EQUIPMENT can injure.
HOT PARTS can burn.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift unit.
D Do not touch hot parts bare handed.
D Allow cooling period before working on
equipment.
D
To handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.
D
D
MOVING PARTS can injure.
D
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
D
D
D
D
FIRE OR EXPLOSION hazard.
Have only qualified persons remove doors, panels, covers, or
guards for maintenance and troubleshooting as necessary.
Reinstall doors, panels, covers, or guards when maintenance is
finished and before reconnecting input power.
READ INSTRUCTIONS.
D Do not locate unit on, over, or near combustible
surfaces.
D Do not install unit near flammables.
D
D Read and follow all labels and the Owner’s
Manual carefully before installing, operating, or
servicing unit. Read the safety information at
the beginning of the manual and in each
section.
Use only genuine replacement parts from the manufacturer.
Perform installation, maintenance, and service according to the
Owner’s Manuals, industry standards, and national, state, and
local codes.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
H.F. RADIATION can cause interference.
D High frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with electronic equipment perform this installation.
D Wear safety glasses with side shields or wear
face shield.
D
ELECTRIC AND MAGNETIC FIELDS (EMF)
can affect Implanted Medical Devices.
D
D Wearers of Pacemakers and other Implanted
Medical Devices should keep away.
D
D
Implanted Medical Device wearers should consult their doctor
and the device manufacturer before going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating
operations.
EXPLODING HYDROGEN hazard.
D When cutting aluminum underwater or with the
water touching the underside of the aluminum,
free hydrogen gas can collect under the workpiece.
D
See your cutting engineer and water table instructions for help.
The user is responsible for having a qualified electrician promptly
correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the equipment
at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
ARC CUTTING can cause interference.
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
OVERUSE can cause OVERHEATING.
D Allow cooling period; follow rated duty cycle.
D Reduce amperage (thickness) or reduce duty
cycle before starting to cut again.
Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
STATIC (ESD) can damage PC boards.
FLYING METAL or DIRT can injure eyes.
D
If using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.
Keep equipment (cables and cords) away from moving vehicles
when working from an aerial location.
Follow the guidelines in the Applications Manual for the Revised
NIOSH Lifting Equation (Publication No. 94−110) when manually
lifting heavy parts or equipment.
D
D
D
D
To reduce possible interference, keep cables as short as possible,
close together, and down low, such as on the floor.
Locate cutting operation 100 meters from any sensitive electronic
equipment.
Be sure this cutting power source is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures such
as moving the machine, using shielded cables, using line filters, or
shielding the work area.
BATTERY EXPLOSION can injure.
D Do not use plasma cutter to charge batteries or
jump start vehicles unless it has a battery charging feature designed for this purpose.
OM-253555 Page 3
1-4. California Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to
the state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after use.
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Recommended Practices for Plasma Arc Cutting and Gouging, American Welding Society Standard AWS C5.2, from Global Engineering
Documents (phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Combustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:
www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5NS
(phone: 800-463-6727, website: www.csagroup.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org).
OSHA, Occupational Safety and Health Standards for General Industry,
Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and
Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—phone
for Region 5, Chicago, is 312-353-2220, website: www.osha.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30329-4027 (phone: 1-800-232-4636, website:
www.cdc.gov/NIOSH).
1-6. EMF Information
Electric current flowing through any conductor causes localized electric
and magnetic fields (EMF). The current from arc welding (and allied processes including spot welding, gouging, plasma arc cutting, and
induction heating operations) creates an EMF field around the welding
circuit. EMF fields can interfere with some medical implants, e.g. pacemakers. Protective measures for persons wearing medical implants
have to be taken. For example, restrict access for passers−by or conduct individual risk assessment for welders. All welders should use the
following procedures in order to minimize exposure to EMF fields from
the welding circuit:
1. Keep cables close together by twisting or taping them, or using a
cable cover.
2. Do not place your body between welding cables. Arrange cables
to one side and away from the operator.
3. Do not coil or drape cables around your body.
OM-253555 Page 4
4. Keep head and trunk as far away from the equipment in the welding circuit as possible.
5. Connect work clamp to workpiece as close to the weld as
possible.
6. Do not work next to, sit or lean on the welding power source.
7. Do not weld whilst carrying the welding power source or wire
feeder.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT
UTILISATION
pom_2015−09fre
Pour écarter les risques de blessure pour vous−même et pour autrui — lire, appliquer et ranger en lieu sûr ces consignes relatives
aux précautions de sécurité et au mode opératoire.
2-1. Signification des symboles
DANGER! − Indique une situation dangereuse qui si on
l’évite pas peut donner la mort ou des blessures graves.
Les dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
Indique une situation dangereuse qui si on l’évite pas
peut donner la mort ou des blessures graves. Les
dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
AVIS − Indique des déclarations pas en relation avec des blessures personnelles.
. Indique des instructions spécifiques.
Ce groupe de symboles veut dire Avertissement! Attention! DANGER
DE CHOC ELECTRIQUE, PIECES EN MOUVEMENT, et PIECES
CHAUDES. Consulter les symboles et les instructions ci-dessous y
afférant pour les actions nécessaires afin d’éviter le danger.
2-2. Dangers liés au coupage à l’arc au plasma
Les symboles présentés ci-après sont utilisés tout au long du
présent manuel pour attirer votre attention et identifier les
risques de danger. Lorsque vous voyez un symbole, soyez
vigilant et suivez les directives mentionnées afin d’éviter tout
danger. Les consignes de sécurité présentées ci-après ne
font que résumer l’information contenue dans les normes de
sécurité énumérées à la section 1-5. Veuillez lire et respecter
toutes ces normes de sécurité.
L’installation, l’utilisation, l’entretien et les réparations ne
doivent être confiés qu’à des personnes qualifiées.
Au cours de l’utilisation, tenir toute personne à l’écart et plus
particulièrement les enfants.
LE COUPAGE présente un risque de
feu ou d’explosion.
Des particules de métal chaud et des étincelles
peuvent jaillir de la pièce au moment du coupage.
Les étincelles et le métal chaud, la pièce à couper
chauffée et l’équipement chaud peuvent causer un
feu ou des brûlures. Avant de commencer à travailler, assurez-vous
que l’endroit est sécuritaire.
D Déplacez toute matière inflammable se trouvant à l’intérieur d’un
périmètre de 10,7 m (35 pi) de la pièce à couper. Si cela est
impossible, vous devez les couvrir avec des housses approuvées
et bien ajustées.
D Ne coupez pas dans un endroit où des étincelles pourraient
atteindre des matières inflammables.
D Protégez−vous, ainsi que toute autre personne travaillant sur les
lieux, contre les étincelles et le métal chaud.
D Assurez−vous qu’aucune étincelle ni particule de métal ne peut se
glisser dans de petites fissures ou tomber dans d’autres pièces.
D Afin d’éliminer tout risque de feu, soyez vigilant et gardez toujours
un extincteur à la portée de la main.
D Si vous coupez sur un plafond, un plancher ou une cloison, soyez
conscient que cela peut entraîner un feu de l’autre côté.
D Ne pas effectuer le soudage sur des conteneurs fermés tels que
des réservoirs, tambours, ou conduites, à moins qu’ils n’aient été
préparés correctement conformément à AWS F4.1 et AWS A6.0
(voir les Normes de Sécurité).
D Fixez le câble de masse sur la pièce à couper, le plus près possible
de la zone à couper afin de prévenir que le courant de coupage ne
prenne une trajectoire inconnue ou longue et ne cause ainsi une
décharge électrique, d’étincelles ou un feu.
D Ne pas utiliser le coupeur plasma pour dégeler des conduites
gelées.
D Ne coupez jamais des contenants qui peuvent contenir des
matières inflammables. Vous devez en premier lieu les vider et les
nettoyer convenablement.
D Ne pas couper là où l’air ambiant pourrait contenir des poussières,
gaz ou émanations inflammables (vapeur d’essence, par
exemple).
D Ne coupez pas de bouteilles, de tuyaux ou de contenants
pressurisés.
D Porter un équipement de protection pour le corps fait d’un matériau
résistant et ignifuge (cuir, coton robuste, laine). La protection du
corps comporte des vêtements sans huile comme par ex. des
gants de cuir, une chemise solide, des pantalons sans revers, des
chaussures hautes et une casquette.
D Ne placez pas le poste sur une surface combustible ou au−dessus
de celle−ci.
D Avant le coupage, retirez tout combustible de vos poches, par
exemple un briquet au butane ou des allumettes.
D Une fois le travail achevé, assurez−vous qu’il ne reste aucune
trace d’étincelles incandescentes ni de flammes.
D Utiliser exclusivement des fusibles ou coupe−circuits appropriés.
Ne pas augmenter leur puissance; ne pas les ponter.
D Suivre les consignes de OSHA 1910.252 (a) (2) (iv) et de NFPA
51B pour travaux de soudage et prévoir un détecteur d incendie et
un extincteur à proximité.
UN CHOC ÉLECTRIQUE peut tuer.
Le contact avec des pièces électriques sous tension
peut causer un choc fatal ou des brûlures graves.
Dès que la sortie de soudage est activée, la torche et
le circuit de travail sont sous tension. Le découpage
à l’arc sous plasma demande une tension départ et
de travail plus élevée que le soudage (typiquement, 200 et 400 V c.c.),
mais permet l’utilisation d’une torche à inter−verrouillage de sécurité
qui coupe l’alimentation de la machine lorsque la coupelle d’écran est
déposée ou si le bec de contact touche l’électrode à l’intérieur de la
buse. Des équipements mal installés ou dont la mise à la masse est
fautive constituent des dangers.
D Ne touchez pas aux pièces électriques sous tension.
D Portez des gants isolants et des vêtements de protection secs et
sans trous.
D Isolez−vous de la pièce à couper et du sol en utilisant des housses
ou des tapis assez grands afin d’éviter tout contact physique avec
la pièce à couper ou le sol.
D Ne touchez pas aux pièces du chalumeau si vous êtes en contact
avec la pièce à couper ou le sol.
D Mettez l’appareil hors tension avant d’effectuer la vérification, le
nettoyage ou le changement d’une pièce du chalumeau.
OM-253555 Page 5
D Coupez l’alimentation d’entrée avant d’installer l’appareil ou
d’effectuer l’entretien. Verrouillez ou étiquetez la sortie
d’alimentation selon la norme OSHA 29 CFR 1910.147
(reportez−vous aux Principales normes de sécurité).
D Installer le poste correctement et le mettre à la terre
convenablement selon les consignes du manuel de l’opérateur et
les normes nationales, départementales et locales.
D Assurez−vous que le fil de terre du cordon d’alimentation est
correctement relié à la borne de terre dans la boîte de coupure ou
que la fiche du cordon est branchée à une prise correctement mise
à la terre − vous devez toujours vérifier la mise à la terre.
D Avant d’effectuer les connexions d’alimentation, vous devez relier
le bon fil de terre.
D Les câbles doivent être exempts d’humidité, d’huile et de graisse;
protégez−les contre les étincelles et les pièces métalliques
chaudes.
D Vérifier fréquemment le cordon d’alimentation et le conducteur de
mise à la terre afin de s’assurer qu’il n’est pas altéré ou dénudé. Le
remplacer immédiatement s’il l’est . Un fil dénudé peut entraîner la
mort.
D L’équipement doit être hors tension lorsqu’il n’est pas utilisé.
D Ne pas utiliser des câbles usés, endommagés, sous dimensionnés
ou réparés.
D Le câble du chalumeau ne doit pas s’enrouler autour de votre
corps.
D Si les normes le stipulent, la pièce à couper doit être mise à la terre.
D Utilisez uniquement de l’équipement en bonne condition. Réparez
ou remplacez immédiatement toute pièce altérée.
D Portez un harnais de sécurité si vous devez travailler au−dessus
du sol.
D Assurez−vous que tous les panneaux et couvercles sont
correctement en place.
D N’essayez pas d’aller à l’encontre des systèmes de verrouillage de
sécurité ou de les contourner.
D Utilisez uniquement le ou les chalumeaux recommandés dans le
manuel de l’opérateur.
D N’approchez pas le tube du chalumeau et l’arc pilote lorsque la
gâchette est enfoncée.
D Le câble de masse doit être pincé correctement sur la pièce à
couper, métal contre métal (et non de telle sorte qu’il puisse se
détacher), ou sur la table de travail le plus près possible de la ligne
de coupage.
D Isoler la pince de masse quand pas mis à la pièce pour éviter le
contact avec tout objet métallique.
DÉCHARGES ÉLECTRIQUES potentiellement mortelles.
Il reste une TENSION DC NON
NÉGLIGEABLE dans les sources de
soudage onduleur UNE FOIS
l’alimentation coupée.
D Mettre l’unité hors tension, mesurer la tension des
condensateurs d’entrée et s’assurer qu’elle est pratiquement
nulle avant de toucher à l’une quelconque des pièces. Mesurer
cette tension conformément aux directives énoncées à la
section Entretien du manuel de l’utilisateur ou du manuel
technique avant de toucher à l’une quelconque des pièces.
Risque de blessure en cas
D’EXPLOSION DES PIÈCES.
D Mise sous tension, toute pièce défectueuse
des sources d’alimentation de l’inverseur peut
exploser ou faire exploser d’autres pièces.
Pour entretenir les inverseurs, toujours porter
un masque protecteur et un vêtement à
manches longues.
OM-253555 Page 6
LES
ÉTINCELLES
PROJETÉES
peuvent provoquer des blessures.
Le coupage plasma produit des étincelles et
projections de métal à très haute température.
Lorsque la pièce refroidit, du laitier peut se former.
D Portez une visière ou des lunettes de sécurité avec des écrans
latéraux approuvées.
D Portez des vêtements de protection adéquats afin de protéger
votre peau.
D Ayez recours à des protège−tympans ou à un serre−tête ignifuges
afin d’éviter que les étincelles n’entrent dans vos oreilles.
LES RAYONS D’ARC peuvent
entraîner des brûlures aux yeux et à la
peau.
Les rayons d’arc provenant du procédé de coupage
produisent des rayons visibles et invisibles intenses
(ultraviolets et infrarouges) qui peuvent entraîner
des brûlures aux yeux et à la peau.
Porter un protecteur facial (casque ou écran) muni d’un filtre de
teinte appropriée pour protéger le visage et les yeux des rayons et
des étincelles quand on coupe ou observe le travail de coupe. Pour
tous les courants de coupe inférieurs à 300 ampères, la norme ANSI Z49.1 (voir section Normes de sécurité) recommande une
opacité de grade 9 (grade minimum de 8). Cette norme ajoute qu’un
filtre plus pâle peut être utilisé si l’arc est caché par la pièce. Comme
c’est normalement le cas pour le coupage à faible courant, les opacités de filtres suggérées au Tableau 1 sont à la disposition de
l’opérateur au besoin.
D Porter des lunettes de sécurité à coques latérales sous votre
casque ou écran facial.
D Ayez recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements, les étincelles et les
éblouissements; prévenez toute personne sur les lieux de ne pas
regarder l’arc.
D Porter un équipement de protection pour le corps fait d’un matériau
résistant et ignifuge (cuir, coton robuste, laine). La protection du
corps comporte des vêtements sans huile comme par ex. des
gants de cuir, une chemise solide, des pantalons sans revers, des
chaussures hautes et une casquette.
D
Tableau 1. Protection des yeux pour le coupage au plasma d’arc
Intensité de courant en ampères
Filtre de teinte (minimum)
Moins de 20
20 − 40
40 − 60
60 − 100
no. 4
no. 5
no. 6
no. 8
LE BRUIT peut endommager l’ouïe.
Certaines applications de coupage produisent un
bruit constant, ce qui peut endommager l’ouïe si le
niveau sonore dépasse les limites permises par
l’OSHA (reportez−vous aux Principales normes de
sécurité).
D Utilisez des protège−tympans ou un serre−tête antibruit si le
niveau sonore est élevé.
D Prévenez toute personne sur les lieux du danger relié au bruit.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
Le coupage produit des vapeurs et des gaz.
Respirer ces vapeurs et ces gaz peut être
dangereux pour la santé.
D Ne mettez pas votre tête au−dessus des vapeurs. Ne respirez pas
ces vapeurs.
D Si vous êtes à l’intérieur au moment du coupage, ventilez la pièce
ou ayez recours à une ventilation aspirante installée près de l’arc
pour évacuer les vapeurs et les gaz. Pour déterminer la bonne
ventilation, il est recommandé de procéder à un prélèvement pour
la composition et la quantité de fumées et de gaz auxquels est
exposé le personnel.
D Si la ventilation est médiocre, utilisez un respirateur anti−vapeurs
approuvé.
D Lire et comprendre les fiches de données de sécurité et les
instructions du fabricant concernant les adhésifs, les revêtements,
les nettoyants, les consommables, les produits de
refroidissement, les dégraisseurs, les flux et les métaux.
D Travaillez dans un espace restreint uniquement s’il est bien ventilé
ou si vous portez un respirateur anti−vapeurs. Les vapeurs
causées par le coupage et l’épuisement de l’oxygène peuvent
altérer la qualité de l’air et entraîner des blessures ou la mort.
Assurez−vous que l’air ambiant est sain pour la santé.
D Ne coupez pas dans un endroit près d’opérations de décapage, de
nettoyage ou de vaporisation. La chaleur et les rayons d’arc
peuvent réagir avec les vapeurs et former des gaz hautement
toxiques et irritants.
D Ne coupez pas des métaux enrobés tels que des métaux
galvanisés, contenant du plomb ou de l’acier plaqué au cadmium, à
moins que l’enrobage ne soit ôté de la surface du métal à couper,
que l’endroit où vous travaillez ne soit bien ventilé, ou que vous ne
portiez un respirateur anti−vapeurs. Les enrobages ou tous
métaux qui contiennent ces éléments peuvent créer des vapeurs
toxiques s’ils sont coupés.
D Ne coupez pas de contenants qui renferment ou ont renfermés des
matières toxiques ou réactives − vous devez en premier lieu les
vider et les nettoyer convenablement.
L’ARC PLASMA peut provoquer des
blessures.
La chaleur dégagée par le plasma d’arc peut
entraîner de sérieuses brûlures. La force de l’arc est
un facteur qui s’ajoute au danger de brûlures. La
chaleur intense et la puissance de l’arc peuvent
rapidement passer au travers de gants et de tissus.
D N’approchez pas le tube du chalumeau.
D Ne saisissez pas la pièce à couper près de la ligne de coupage.
D L’arc pilote peut causer des brûlures − n’approchez pas le tube du
chalumeau lorsque vous avez appuyé sur le gâchette.
D Porter un équipement de protection pour le corps fait d’un matériau
résistant et ignifuge (cuir, coton robuste, laine). La protection du
corps comporte des vêtements sans huile comme par ex. des
gants de cuir, une chemise solide, des pantalons sans revers, des
chaussures hautes et une casquette.
D Ne pointez pas le chalumeau en direction de votre corps ni de la
pièce à couper lorsque vous appuyez sur la gâchette − l’arc pilote
s’allume automatiquement.
D Mettez l’alimentation hors tension et débranchez le cordon
d’alimentation avant de démonter le chalumeau ou de changer une
pièce du chalumeau.
D Utilisez uniquement le ou les chalumeaux recommandés dans le
manuel de l’opérateur.
LES BOUTEILLES peuvent exploser
si elles sont endommagées.
Les bouteilles de gaz comprimé contiennent du gaz
sous haute pression. Si une bouteille est
endommagée, elle peut exploser. Puisque les
bouteilles de gaz font habituellement partie d’un
processus de travail des métaux, assurez−vous de les manipuler
correctement.
D Protégez les bouteilles de gaz comprimé contre la chaleur
excessive, les chocs mécaniques, des dommages physiques, le
laitier, la flamme, les étincelles et l’arc.
D Installez et attachez les bouteilles dans la position verticale à l’aide
d’une chaîne, sur un support stationnaire ou un châssis
porte−bouteille afin de prévenir qu’elles ne tombent ou ne
basculent.
D Les bouteilles ne doivent pas être près de la zone de coupage ni de
tout autre circuit électrique.
D Un contact électrique ne doit jamais se produire entre un
chalumeau de plasma d’arc et une bouteille.
D Ne coupez jamais sur une bouteille pressurisée − une explosion en
résulterait.
D Utilisez uniquement des bouteilles de gaz comprimé , des
détendeurs, des boyaux et des raccords conçus pour l’application
déterminée. Gardez−les, ainsi que toute autre pièce associée, en
bonne condition.
D Tourner le dos à la sortie de vanne lors de l’ouverture de la vanne
de la bouteille. Ne pas se tenir devant ou derrière le régulateur lors
de l’ouverture de la vanne.
D Le couvercle du détendeur doit toujours être en place, sauf lorsque
vous utilisez la bouteille ou qu’elle est reliée pour usage ultérieur.
D Utiliser les équipements corrects, les bonnes procédures et
suffisamment de personnes pour soulever et déplacer les
bouteilles.
D Lire et suivre les instructions sur les bouteilles de gaz comprimé,
l’équipement connexe et le dépliant P-1 de la CGA (Compressed
Gas Association) mentionné dans les principales normes de
sécurité.
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la
maintenance
LES PIÈCES CHAUDES
provoquer des brûlures.
peuvent
D Ne pas toucher des parties chaudes à mains
nues.
D Prévoir une période de refroidissement avant
d’utiliser l’équipement.
D Ne pas toucher aux pièces chaudes, utiliser les outils recommandés et porter des gants de soudage et des vêtements épais
pour éviter les brûlures.
Les PIÈCES MOBILES
provoquer des blessures.
peuvent
D S’abstenir de toucher des organes mobiles tels
que des ventilateurs.
D Maintenir fermés et verrouillés les portes,
panneaux, recouvrements et dispositifs de
protection.
D Lorsque cela est nécessaire pour des travaux d’entretien et de
dépannage, faire retirer les portes, panneaux, recouvrements
ou dispositifs de protection uniquement par du personnel
qualifié.
D Remettre les portes, panneaux, recouvrements ou dispositifs de
protection quand l’entretien est terminé et avant de rebrancher
l’alimentation électrique.
OM-253555 Page 7
LIRE LES INSTRUCTIONS.
D Lire et appliquer les instructions sur les
étiquettes et le Mode d’emploi avant
l’installation, l’utilisation ou l’entretien de
l’appareil. Lire les informations de sécurité au
début du manuel et dans chaque section.
D N’utiliser que les pièces de rechange recommandées par le
constructeur.
D Effectuer l’installation, l’entretien et toute intervention selon les manuels d’utilisateurs, les normes nationales, provinciales et de
l’industrie, ainsi que les codes municipaux.
DES PIECES DE METAL ou DES
SALETES peuvent provoquer des
blessures dans les yeux.
D Porter des lunettes de sécurité avec écrans
latéraux ou un écran facial.
Les CHAMPS ÉLECTROMAGNÉTIQUES
(CEM) peuvent affecter les implants
médicaux.
D Les porteurs de stimulateurs cardiaques et
autres implants médicaux doivent rester à
distance.
D Les porteurs d’implants médicaux doivent consulter leur
médecin et le fabricant du dispositif avant de s’approcher de la
zone où se déroule du soudage à l’arc, du soudage par points, du
gougeage, de la découpe plasma ou une opération de chauffage
par induction.
L’EMPLOI EXCESSIF peut
SURCHAUFFER L’ÉQUIPEMENT.
D Prévoir une période de refroidissement;
respecter le cycle opératoire nominal.
D Réduire l’ampérage (épaisseur) avant de
continuer à couper ou réduire le facteur de
marche.
Danger D’EXPLOSION
D’HYDROGÈNE.
D Lors du coupage d’aluminium sous l’eau ou
avec de l’eau touchant le dessous de l’aluminium, une libération d’hydrogène peut s’accumuler sous la pièce.
D Consultez votre ingénieur de coupage et les instructions de la
table de coupage.
D En utilisant des fourches de levage pour déplacer l’unité, s’assurer
que les fourches sont suffisamment longues pour dépasser du
côté opposé de l’appareil.
D Tenir l’équipement (câbles et cordons) à distance des véhicules
mobiles lors de toute opération en hauteur.
D Suivre les consignes du Manuel des applications pour l’équation
de levage NIOSH révisée (Publication Nº94–110) lors du levage
manuelle de pièces ou équipements lourds.
Risque D’INCENDIE OU
D’EXPLOSION.
D Ne pas installer l’appareil à proximité de
produits inflammables
D Ne pas placer l’appareil sur, au-dessus ou à proximité de surfaces
inflammables.
D Ne pas surcharger l’installation électrique − s’assurer que
l’alimentation est correctement dimensionné et protégé avant de
mettre l’appareil en service.
LES CHARGES ÉLECTROSTATIQUES
peuvent endommager les circuits imprimés.
D Établir la connexion avec la barrette de terre
avant de manipuler des cartes ou des pièces.
D Utiliser des pochettes et des boîtes antistatiques pour stocker,
déplacer ou expédier des cartes PC.
LE
RAYONNEMENT
HAUTE
FRÉQUENCE
(H.F.)
risque
de
provoquer des interférences.
D Le Rayonnement haute fréquence (H.F.) peut
provoquer des interférences avec les
équipements de radio−navigation et de
communication, les services de sécurité et les
ordinateurs.
D Demander seulement à des personnes qualifiées familiarisées
avec des équipements électroniques de faire fonctionner
l’installation.
D L’utilisateur est tenu de faire corriger rapidement par un électricien
qualifié les interférences résultant de l’installation.
D Si le FCC signale des interférences, arrêter immédiatement
l’appareil.
D Effectuer régulièrement le contrôle et l’entretien de l’installation.
D Maintenir soigneusement fermés les portes et les panneaux des
sources de haute fréquence, maintenir les éclateurs à une
distance correcte et utiliser une terre et et un blindage pour réduire
les interférences éventuelles.
L’EXPLOSION DE LA BATTERIE peut
provoquer des blessures.
LE COUPAGE Ã L’ARC peut causer
des interférence.
D Ne pas utiliser le découpeur plasma pour charger
des batteries ou faire démarrer des véhicules à
l’aide de câbles de démarrage, sauf si l’appareil
dispose d’une fonctionnalité de charge de
batterie destinée à cet usage.
D L’énergie électromagnétique peut gêner le
fonctionnement d’appareils électroniques
comme des ordinateurs et des robots.
LA CHUTE DE L’ÉQUIPEMENT peut
provoquer des blessures.
D Utiliser l’anneau de levage uniquement pour
soulever l’appareil, NON PAS les chariot, les
bouteilles de gaz ou tout autre accessoire.
D Utiliser un engin d’une capacité appropriée pour soulever
l’appareil.
OM-253555 Page 8
D Pour réduire la possibilité d’interférence, maintenir les câbles aussi
courts que possible, les grouper, et les poser aussi bas que
possible (ex. par terre).
D Veiller à couper à une distance de 100 mètres de tout équipement
électronique sensible.
D S’assurer que la source de coupage est correctement branchée et
mise à la terre.
D Si l’interférence persiste, l’utilisateur doit prendre des mesures
supplémentaires comme écarter la machine, utiliser des câbles
blindés de des filtres, ou boucler la zone de travail.
2-4. Proposition californienne 65 Avertissements
Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des
malformations congénitales et, dans certains cas, des
cancers. (Code de santé et de sécurité de Californie, chapitre
25249.5 et suivants)
Ce produit contient des éléments chimiques, dont le plomb,
reconnus par l’État de Californie pour leur caractère
cancérogène ainsi que provoquant des malformations
congénitales ou autres problèmes de procréation. Se laver les
mains après toute manipulation.
2-5. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Recommended Practices for Plasma Arc Cutting and Gouging,
American Welding Society Standard AWS C5.2, from Global
Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from
Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held
Combustibles, American Welding Society Standard AWS A6.0, from
Global Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire
Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555,
website: www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:
www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5NS
(phone: 800-463-6727, website: www.csagroup.org).
Safe Practice For Occupational And Educational Eye And Face
Protection, ANSI Standard Z87.1, from American National Standards
Institute, 25 West 43rd Street, New York, NY 10036 (phone:
212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org).
OSHA, Occupational Safety and Health Standards for General Industry,
Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and
Part 1926, Subpart J, from U.S. Government Printing Office,
Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA
15250-7954 (phone: 1-866-512-1800) (there are 10 OSHA Regional
Offices—phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
Applications Manual for the Revised NIOSH Lifting Equation, The
National Institute for Occupational Safety and Health (NIOSH), 1600
Clifton Rd, Atlanta, GA 30329-4027 (phone: 1-800-232-4636, website:
www.cdc.gov/NIOSH).
2-6. Informations relatives aux CEM
Le courant électrique qui traverse tout conducteur génère des champs
électromagnétiques (CEM) à certains endroits. Le courant issu d’un
soudage à l’arc (et de procédés connexes, y compris le soudage par
points, le gougeage, le découpage plasma et les opérations de
chauffage par induction) crée un champ électromagnétique (CEM)
autour du circuit de soudage. Les champs électromagnétiques produits
peuvent causer interférence à certains implants médicaux, p. ex. les
stimulateurs cardiaques. Des mesures de protection pour les porteurs
d’implants médicaux doivent être prises: Limiter par exemple tout accès
aux passants ou procéder à une évaluation des risques individuels pour
les soudeurs. Tous les soudeurs doivent appliquer les procédures
suivantes pour minimiser l’exposition aux CEM provenant du circuit de
soudage:
1. Rassembler les câbles en les torsadant ou en les attachant avec
du ruban adhésif ou avec une housse.
2. Ne pas se tenir au milieu des câbles de soudage. Disposer les
câbles d’un côté et à distance de l’opérateur.
3. Ne pas courber et ne pas entourer les câbles autour de votre
corps.
4. Maintenir la tête et le torse aussi loin que possible du matériel du
circuit de soudage.
5. Connecter la pince sur la pièce aussi près que possible de la
soudure.
6. Ne pas travailler à proximité d’une source de soudage, ni
s’asseoir ou se pencher dessus.
7. Ne pas souder tout en portant la source de soudage ou le
dévidoir.
En ce qui concerne les implants médicaux :
Les porteurs d’implants doivent d’abord consulter leur médecin avant de
s’approcher des opérations de soudage à l’arc, de soudage par points,
de gougeage, du coupage plasma ou de chauffage par induction. Si le
médecin approuve, il est recommandé de suivre les procédures
précédentes.
OM-253555 Page 9
OM-253555 Page 10
SECTION 3 − DEFINITIONS
3-1. Additional Safety Symbols And Definitions
. Some symbols are found only on CE products.
Warning! Watch Out! There are possible hazards as shown by the symbols.
Safe1 2012−05
When power is applied failed parts can explode or cause other parts to explode.
Safe26 2012−05
3-2. Miscellaneous Symbols And Definitions
. Some symbols are found only on CE products.
A
V
Amperes
I2
Volts
Protective Earth
(Ground)
pf
On
U0
I1max
IP
I1eff
Rated No Load
Voltage (OCV)
Increase
Loose Shield Cup
Temperature
Power Factor
Voltage Input
Adjust Air/Gas
Pressure
Direct Current
Line Connection
Single Phase
Static Frequency
ConverterTransformerRectifier
Constant Current
Degree Of
Protection
Plasma Arc
Cutting (PAC)
Low Air Pressure
Light
No − Do Not Do
This
Rated Maximum
Supply Current
Maximum Effective Supply Current
Rated Welding Or
Cutting Current
Percent
U2
X
Conventional
Load Voltage
Hz
Hertz
S1
Power Rating,
Product Of
Voltage And
Current (kVA)
Duty Cycle
Look Under Unit
for Label
Input
Single Phase
Off
U1
S
Suitable for Some
Hazardous
Locations
P
Power
Primary Voltage
OM-253555 Page 11
. A complete Parts List is available at www.MillerWelds.com
SECTION 4 − SPECIFICATIONS
4-1. Serial Number And Rating Label Location
The serial number and rating information for this product is located on the bottom. Use rating label to determine input power requirements and/or rated
output. For future reference, write serial number in space provided on back cover of this manual.
4-2. Unit Specifications
. Do not use information in unit specifications table to determine electrical service requirements. See Sections 5-5, 5-8, and 5-9 for information on
connecting input power.
. This equipment will deliver rated output at an ambient air temperature up to 1045F (405C).
A. Power Supply
Input
1 − Phase, 50 / 60 Hz
Rated AC Phase and line frequency (Hz)
Rated Input Voltage (U1) and rated Input Current (I1) and I1 eff at rated output. I1 eff used
to determine power cord rating
Power Factor/kVA/kW at Rated Output
Volts AC RMS − (U1)
Amps RMS − (I1)
I1 eff
120 VAC, 1−Phase (20 A)
25.6
11.4
120 VAC, 1−Phase (15 A)
18.1
10.7
240 VAC, 1−Phase
13.6
8.1
Volts AC RMS − (U1)
Power Factor
kVA/kW
120 VAC, 1−Phase (20 A)
0.982
3.08/3.03
120 VAC, 1−Phase (15 A)
0.983
2.19/2.15
240 VAC, 1−Phase
0.995
3.31/3.29
7.0 kW
Peak kW at Arc Stretch
Output
400 Volts DC/Electrode Negative
Rated Open Circuit Voltage (U0) Type
Constant Current
Output Characteristic
Rated Output Current and Voltage (I2, U2) at
rated Input Voltage (U1)
Volts AC RMS - (U1)
Amps DC - (I2)
Volts DC - (U2)
120 VAC, 1−Phase (20A)
27 A
91 V
120 VAC, 1−Phase (15 A)
20 A
88 V
30 A
92 V
240 VAC, 1−Phase
15 − 30 A
Output Current Range
Duty Cycle at 104°F (405C) and Rated
Conditions (U1, I1, U2, I2) based on a 10
minute period
Volts AC RMS - (U1)
Amps DC − (I2)
Duty Cycle %
120 VAC, 1−Phase (20A)
27 A
20%
120 VAC, 1−Phase (15 A)
20 A
35%
240 VAC, 1−Phase
30 A
35%
240 VAC, 1−Phase
22 A
100%
General
Toppling or tilting
Weight
OM-253555 Page 12
Up to 15° incline
18 lb (8.2 kg) including torch
. A complete Parts List is available at www.MillerWelds.com
B. Torch
The XT30 torch is intended for handheld use only. The torch conforms to IEC 60974-7 when used with the Spectrum 375 X-TREME.
Do not use this torch in combination with any other machines.
Air
Gas Type
Clean, moisture−free, oil−free
Gas Quality
5.0 SCFM (142 L/min)
90 psi (621 kPa) Min
Gas Inlet Flow and Pressure
120 psi (827 kPa) Max
Particulates to 5 microns
Gas Filtering
Mild Steel capacities (see Section 6-2 for cutting speeds vs material type and thickness)
Cooling Method
Air
Duty Cycle of Torch
100% at 30 Amps
Rating of Electrical Controls (Trigger)
30 VDC at 0.1 Amps
Rating of Electrical Controls (Cup)
30 VDC at 1 Amp
Approved Systems
Spectrum 375 X-TREME w/XT30 torch
Trigger Protection
Safety trigger guard
Safety Devices
Safety interlock devices shut down power source
Rated Capacity (edge start)
3/8 in. at 18 ipm (457 mm/min)*
Sever Cut Capacity (edge start)
5/8 in.
Pierce Capacity
3/16 in.
*Travel speeds are approximately 80% of maximum.
Requirements for the torch connection
S Use only compressed air which is free from dirt, oil, and water.
S Ensure that the connections are properly assigned and tightened.
S For torch replacement, see Miller torch manual Part No. OM-254449
S Ensure correct air pressure (flow pressure) and airflow (volume) are set. Insufficient airflow can lead to the torch overheating.
4-3. Torch Dimensions And Weight
8-3/4 in.
(222 mm)
1-3/16 in.
(30 mm)
2.2 lb (1.0 kg)
1-1/2 in.
(38 mm)
Ref. 253 554-A
OM-253555 Page 13
. A complete Parts List is available at www.MillerWelds.com
4-4. Power Source Dimensions And Weight
5-1/2 in.
(140 mm)
Dimensions And Weight
18 lb (8.2 kg)
including torch
9 in.
(229 mm)
13-1/8 in.
(333 mm)
4-5. Duty Cycle And Overheating
Duty Cycle is percentage of 10
minutes that unit can cut at rated
load without overheating.
20% duty cycle
2 Minutes Cutting
8 Minutes Resting
35% duty cycle
3-1/2 Minutes Cutting
If unit overheats, thermostat(s)
opens, output stops, Temperature
trouble light goes On, and cooling
fan runs. Wait fifteen minutes for
unit to cool or temperature light to
go off. Reduce amperage or duty
cycle before cutting.
NOTICE − Exceeding duty cycle
can damage unit and void warranty.
6-1/2 Minutes Resting
sduty1 5/95 / Ref. 804 503-A
Overheating
A
0
15
OR
Reduce Duty Cycle
Minutes
4-6. Environmental Specifications
A. IP Rating
IP Rating
IP23CS
This equipment is designed for outdoor use. It may be stored, but is not intended to be used for cutting outside during precipitation unless
sheltered.
B. Temperature Specifications
Operating Temperature Range*
Storage/Transportation Temperature Range
5 to 104°F (−15 to 40°C)
−4 to 131°F (−20 to 55°C)
*Output is derated at temperatures above 104°F (40°C).
OM-253555 Page 14
Temp_2016- 07
. A complete Parts List is available at www.MillerWelds.com
SECTION 5 − INSTALLATION
5-1. Selecting A Location
!
Do not move or operate
unit where it could tip.
1
Location
!
Special installation may be
required where gasoline or
volatile liquids are present −
see NEC Article 511 or CEC
Section 20.
1
Shoulder Strap
2
Use strap to lift unit.
2
18 in.
(460 mm)
Line Disconnect Device
Locate unit near correct input
power supply.
Locate unit at least 18 in. (460 mm)
away from a wall or other
obstruction to allow adequate
clearance for cooling air flow.
18 in.
(460 mm)
loc_small 2015-04 - Ref. ST-151 556 / Ref. 804 503-A
5-2. Connecting Gas/Air Supply
. Use only clean, dry air with 90
to 120 psi (621 to 827 kPa)
pressure.
1
2
3
Tools Needed:
1
Gas/Air Inlet Opening
2
Hose
3
Teflon Tape
Obtain hose with 1/4 NPT righthand thread fitting. Wrap threads
with teflon tape (optional) or apply
pipe sealant, and install fitting in
opening. Route hose to gas/air
supply.
From Gas/Air
Supply
9/16 in.
Ref. 251 808-A
OM-253555 Page 15
. A complete Parts List is available at www.MillerWelds.com
5-3. Connecting And Disconnecting Work Cable
!
Turn off power source and
disconnect input power.
1
2
Work Cable Plug
Work Cable Receptacle
To connect plug, align key with
receptacle keyway and insert into
receptacle. Rotate plug clockwise
(hand tight only) 1/4 turn to secure in
receptacle.
2
To disconnect plug, rotate counterclockwise until key aligns with keyway and pull plug from receptacle.
1
ZZ
5-4. Connecting Work Clamp
1
2
Work Clamp
Workpiece
Connect work clamp to a clean,
paint-free location on workpiece, as
close to cutting area as possible.
1
2
Ref. 803 640-A
OM-253555 Page 16
. A complete Parts List is available at www.MillerWelds.com
5-5. Electrical Service Guide
Elec Serv 2015−05
Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommendations are for a dedicated circuit sized for the rated output and duty cycle of the welding power source.
In dedicated circuit installations, the National Electrical Code (NEC) allows the receptacle or conductor rating to be less than the rating
of the circuit protection device. All components of the circuit must be physically compatible. See NEC articles 210.21, 630.11, and
630.12.
50/60 Hz Single Phase
120
Input Voltage (V)
240
14
Input Amperes (A) At Rated Output
Max Recommended Standard Fuse Rating In Amperes 1
A 15 or 20
ampere individual
branch circuit
protected by
time-delay fuses
or circuit breaker
is required.
See Section 4-2
Time-Delay Fuses 2
Normal Operating Fuses 3
Min Input Conductor Size In AWG
4
Max Recommended Input Conductor Length In Feet (Meters)
15
25
14
96
(29)
Min Grounding Conductor Size In AWG 4
14
Reference: 2014 National Electrical Code (NEC) (including article 630)
1 If a circuit breaker is used in place of a fuse, choose a circuit breaker with time-current curves comparable to the recommended fuse.
2 “Time-Delay” fuses are UL class “RK5” . See UL 248.
3 “Normal Operating” (general purpose - no intentional delay) fuses are UL class “K5” (up to and including 60 amps), and UL class “H” ( 65 amps and
above).
4 Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table
310.15(B)(16). If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable
requirements.
5-6. Extension Cord Data
. When calculating max. cord length, remember to include conductor length from line disconnect device to input power receptacle.
Conductor Size − AWG (mm2)*
Single Phase AC
Input Voltage
6 (13.3)
8 (8.4)
10 (5.3)
12 (3.3)
14 (2.1)
Maximum Allowable Cord Length in ft (m)
120
175 (53)
110 (33)
70 (21)
44 (13)
28 (9)
240
700 (213)
440 (134)
277 (84)
175 (53)
110 (33)
*Conductor size is based on maximum 3% voltage drop
OM-253555 Page 17
. A complete Parts List is available at www.MillerWelds.com
5-7. Multi−Voltage Plug (MVP) Connection
Selecting Plug
2
1
3
4
5
!
Do not cut off power cord connector and rewire. The power
cord connector and plugs will
work with standard NEMA receptacles. Modifying power
cord, connector, and plugs
will void product warranty.
6
7
Connecting Plug To Power Cord
Selecting Plug
1
Power Cord Connector From
Welding Power Source
Select plug for power supply receptacle
available at site. Not all plugs shown are
provided as standard with unit.
2
Plug − NEMA Type 5−15P
3
Receptacle − NEMA Type 5−15R
(Customer Supplied)
4
5
6
7
!
Plug − NEMA Type 5−20P (Optional)
Receptacle − NEMA Type 5−20R
(Customer Supplied)
Plug − NEMA Type 6−50P
Receptacle − NEMA Type 6−50R
(Customer Supplied)
Follow electrical service guide for
240 VAC in Section 5-5. Do not use
plug rating to size branch circuit
protection.
Connecting Plug To Power Cord
Align arrow on plug with arrow on power
cord connector. Push together.
Tighten threaded collar. As threaded collar
is tightened, push plug onto adapter until
collar is completely tight.
Connect plug to receptacle.
MVP Plug1 2010−10 / Ref. 803 812-C
OM-253555 Page 18
. A complete Parts List is available at www.MillerWelds.com
5-8. Connecting 120 Volt Input Power
!
Installation must meet all National and
Local Codes − have only qualified
persons make this installation.
!
Special installation may be required
where gasoline or volatile liquids are
present − see NEC Article 511 or CEC Section 20.
See rating label on unit and check input voltage
available at site.
. The Auto-Line circuitry in this unit automati-
cally links the power source to the primary
voltage being applied, either 120 or 240 VAC.
For 120 volts AC input power, a 15 or 20 ampere
individual branch circuit protected by time-delay
fuses or circuit breaker is required.
1
Multi-Voltage Plug And Power Cord
Connector (NEMA Type 5−15P Plug
Shown)
For multi−voltage plug connections, see Section
5-7.
2
Receptacle − NEMA Type 5−15R
(Customer Supplied)
1
2
Input6 2011−03 Ref. 253 558-A
OM-253555 Page 19
. A complete Parts List is available at www.MillerWelds.com
5-9. Connecting 1-Phase Input Power For 240 VAC
1
3
=GND/PE Earth Ground
7
2
4
L1
L2
5
6
1
9
8
L1
L2
240 VAC, 1
Tools Needed:
Input4 2012−05 − 803 766-B / Ref. 802 443-A /Ref. 251 808-A
OM-253555 Page 20
. A complete Parts List is available at www.MillerWelds.com
5-9. Connecting 1-Phase Input Power For 240 VAC (Continued)
!
Installation must meet all National and
Local Codes − have only qualified persons make this installation.
!
Disconnect and lockout/tagout input
power before connecting input conductors from unit. Follow established
procedures regarding the installation
and removal of lockout/tagout
devices.
!
Always connect green or green/yellow
conductor to supply grounding terminal first, and never to a line terminal.
NOTICE − The Auto-Line circuitry in this unit
automatically adapts the power source to the
primary voltage being applied, either 120 or
240 VAC.
See rating label on unit and check input voltage available at site.
3
Disconnect Device Grounding Terminal
4
Disconnect Device Line Terminals
5
Black And White Input Conductor (L1
And L2)
6
Green Or Green/Yellow Grounding
Conductor
Connect input conductors L1 and L2 to disconnect device line terminals.
7 Over-Current Protection
Select type and size of over-current protection using Section 5-5 (fused disconnect
switch shown).
8 Receptacle (NEMA 6-50R)
Customer Supplied
9 Multi-Voltage Plug And Power Cord
Connector (NEMA Type 6−50P Plug
Shown)
For multi−voltage plug connections, see Section 5-7.
Connect green or green/yellow grounding
conductor to disconnect device grounding
terminal first.
Close and secure door on disconnect device.
Follow established lockout/tagout procedures to put unit in service.
1
Input Power Cord
2
Disconnect Device (switch shown in the
OFF position)
input4 2012−05
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
OM-253555 Page 21
. A complete Parts List is available at www.MillerWelds.com
SECTION 6 − OPERATION
6-1. Controls
2
1
3
253 014-A / Ref. 251 808-A
4
1
Output Control
Use control to set cutting output.
If 22-27 amperes of cutting output is used
with 120 VAC input power, and the overload
OM-253555 Page 22
protection on the input power circuit frequently opens, either reduce the cutting output and/or the cut time or find more adequate
power (see Section 4-2).
2 Power Light
3
Trouble Lights (See Section 7-7)
4
Power Switch
Use switch to turn unit On or Off.
. A complete Parts List is available at www.MillerWelds.com
6-2. Cutting Speed
Recommended Cut Speeds At 30 Amperes Output
Material Thickness
Mild Steel
Recommended Cut Speeds*
Inches
mm
IPM
mm/min
12ga (0.11)
2.8
105
2662
1/8 (0.13)
3.2
98
2499
3/16 (0.19)
4.8
63
1605
1/4 (0.25)
6.4
36
914
3/8 (0.38)
9.5
18
467
1/2 (0.50)
12.7
10
264
5/8 (0.63)
15.9
6
163
*Recommended Cut Speed is approximately 80% of maximum.
. Aluminum and Stainless Steel cut speeds at these thicknesses may be reduced as much as 20%.
Recommended Cut Speeds At 27 Amperes Output
Material Thickness
Mild Steel
Recommended Cut Speeds*
Inches
mm
IPM
mm/min
12ga (0.11)
2.8
115
2921
1/8 (0.13)
3.2
88
2235
3/16 (0.19)
4.8
50
1280
1/4 (0.25)
6.4
28
711
3/8 (0.38)
9.5
15
386
1/2 (0.50)
12.7
8
203
5/8 (0.63)
15.9
5
123
*Recommended Cut Speed is approximately 80% of maximum.
. Aluminum and Stainless Steel cut speeds at these thicknesses may be reduced as much as 20%.
Recommended Cut Speeds At 20 Amperes Output
Material Thickness
Mild Steel
Recommended Cut Speeds*
Inches
mm
IPM
mm/min
16ga (0.06)
1.6
158
4014
1/8 (0.13)
3.2
50
1260
3/16 (0.19)
4.8
33
833
1/4 (0.25)
6.4
17
427
5/16 (0.31)
7.9
8
203
3/8 (0.38)
9.5
6
163
*Recommended Cut Speed is approximately 80% of maximum.
. Aluminum and Stainless Steel cut speeds at these thicknesses may be reduced as much as 20%.
OM-253555 Page 23
. A complete Parts List is available at www.MillerWelds.com
6-3. Trigger Safety Lock
1
Trigger
1
Trigger Unlocked
Trigger Locked
Ref. 253554-A
6-4. Plasma Cutting System Practices
!
Always connect work clamp to a clean,
paint-free location on workpiece, as close to
cutting area as possible.
The pilot arc starts immediately
when trigger is pressed.
DO NOT start pilot arc without cutting
as this shortens the service life of the
nozzle and electrode.
90°
Maintain approximately a 90° angle to the
workpiece surface for proper cutting results.
Sparks should pass through the workpiece
and out the bottom when cutting.
If sparks flare back from surface, this
usually is an indication that either travel
speed is too fast or amperage is set too low.
Wt
1/16 in.
(1.6 mm)
When doing extended (non-shielded)
cutting, maintain approximately 1/16 in.
standoff between electrode and surface.
DO NOT put pressure on shield when
drag cutting; instead, slide shield along
the surface for proper cutting results.
Pulling rather than pushing the torch
makes cutting easier. Use a proper guide
or template for accurate cutting operations.
Ref. 254 087-A
OM-253555 Page 24
. A complete Parts List is available at www.MillerWelds.com
6-5. Sequence Of Cutting Operation
90°
Connect work clamp to a clean, paint-free
location on workpiece, as close to cutting
area as possible.
!
For standard (shielded) cutting, place drag shield on edge
of metal. For extended (non-shielded) cutting, use 1/8 in.
(3.2 mm) standoff distance (dragging tip will reduce tip life).
The pilot arc starts immediately
when trigger is pressed.
Raise trigger lock and press
trigger. Pilot arc starts.
Adjust torch speed so
sparks go thru metal and
out bottom of cut.
After cutting arc starts, slowly
start moving torch across metal.
Pause briefly at end of
cut before releasing trigger.
Postflow continues for approx. 20 seconds
after releasing trigger; cutting arc can be
instantly restarted during postflow by raising
trigger lock and pressing trigger.
Ref. 254 087-A
OM-253555 Page 25
. A complete Parts List is available at www.MillerWelds.com
6-6. Sequence Of Piercing Operation
!
The pilot arc starts immediately
when trigger is pressed.
45°
Connect work clamp to a clean, paint-free
location on workpiece, as close to cutting
area as possible.
90°
Rotate torch to upright position
approximately 90° to surface.
When arc has pierced through
workpiece, start cutting.
Hold torch at approximately 45°
to the workpiece. Raise trigger
lock and press trigger. Pilot arc
starts.
90°
Maintain approximately 90° torch
position to surface, and continue
cutting.
Release trigger. Postflow continues for
approx. 20 seconds after releasing trigger;
arc can be instantly restarted during postflow
by raising trigger lock and pressing trigger.
Ref. 254 087-A
OM-253555 Page 26
. A complete Parts List is available at www.MillerWelds.com
SECTION 7 − MAINTENANCE & TROUBLESHOOTING
7-1. Routine Maintenance
!
n = Check
Z = Change
~ = Clean
* To be done by Factory Authorized Service Agent
Disconnect power
before maintaining.
. Maintain more often
during severe conditions.
l = Replace
Reference
Each
Use
Section 5-2,
7-6
n Gas/Air Pressure
n Torch Tip, Electrode,
And Shield Cup
Every
Week
Section 7-4
n Shield Cup Shutdown
System
Every
3
Months
l Damaged Or Unreadable
Labels
~ Air Filter/Regulator
l Cracked Parts
n l Gas/Air Hose
Section 7-5,
9
n l Torch Body, Cable
Every
6
Months
OR
~ Inside Unit
7-2. Overload Protection
1
Supplementary Protector CB1
CB1 protects unit from overload. If
CB1 opens, unit shuts down.
Reset supplementary protector.
1
Ref. 251 808-A
OM-253555 Page 27
. A complete Parts List is available at www.MillerWelds.com
7-3. Wrapper Removal
2
!
Turn
off
power,
and
disconnect input power plug
from receptacle or turn off and
lockout/tagout line disconnect device before working on
unit.
!
Significant DC voltage can
remain on capacitors after unit
is Off. Check to see that front
panel lights (LEDs) have
stopped flashing and are off
before removing wrapper.
1
2
Wrapper
Torx Screws (Fine Thread)
1
Tools Needed:
Torx 25
Remove Torx screws and slide
wrapper off.
Ref. 251 808-A
7-4. Checking Shield Cup Shutdown System
. Power must be reset whenever the
cup shutdown system is activated.
Always turn Off power when
changing or checking consumables. Do NOT over tighten torch
shield cup. Gently finger tighten
cup onto torch.
1
Torch Shield Cup
Turn Power On and loosen shield cup. If
shutdown system works properly, Cup
light comes on. If not, immediately turn
Off power and have Factory Authorized
Service Agent check unit.
1
If system works properly, retighten cup
and reset power.
Ref. 253 554-A
7-5. Checking Or Replacing Filter Element
1
2
3
Tools Needed:
Torx 25
Ref. 251 808-A / Ref. 804 506-B
!
Significant DC voltage can remain
on capacitors after unit is Off.
Check to see that front panel lights
(LEDs) have stopped flashing and
are off before removing wrapper.
Turn power Off, and disconnect input
power plug from receptacle. Remove
wrapper from unit (see Section 7-3).
OM-253555 Page 28
1
Filter Base
2
Filter
3
Filter Cup
Unscrew filter cup from base.
Check filter element for dirt and moisture,
and replace if necessary.
Be sure that all parts are clean and dry.
Remove cup.
Reinstall filter element, and secure filter
cup.
Unscrew filter element from base.
Reinstall wrapper.
. A complete Parts List is available at www.MillerWelds.com
7-6. Checking/Replacing Retaining Cup, Tip, And Electrode
Make sure this area is
clean of any debris.
4
6
5
3
New
2
1
New
Worn
Worn
Ref. 253554-A
!
!
!
Turn Off power source before checking torch parts.
Overtightening will strip threads. Do
not overtighten retaining cup during
assembly. Do not cross-thread parts
causing stripping. Use care during
torch
assembly
and
parts
replacement.
Inspect shield cup, tip, and electrode
for wear before cutting or whenever
cutting speed has been significantly
reduced. Do not operate torch without a tip or electrode in place. Be sure
to use genuine replacement parts.
. A good practice is to replace both the tip
and electrode at the same time.
1
Shield Cup
Remove shield cup. Check cup for cracks,
and replace if necessary.
1/32 in. (1 mm) to 1/16 in. (2 mm) maximum
pit depth depending on acceptable cut
quality
2
Tip
5
3
Opening
Remove swirl ring. Check ring, and replace
if side holes are plugged.
Remove tip. Check tip, and replace if opening is deformed or 50% oversize. If inside of
tip is not clean and bright, clean with steel
wool. Be sure to remove any pieces of steel
wool afterwards.
4
Electrode
Check electrode. If center has a pit more
than a 1/16 in. (2 mm) deep, remove and replace electrode.
Swirl Ring
. Make sure swirl ring is clean of any debris and no holes are obstructed.
6
O-Ring
Check O-ring for cracks or worn spots, and
replace if necessary.
Carefully reassemble parts in reverse order.
OM-253555 Page 29
. A complete Parts List is available at www.MillerWelds.com
7-7. Status/Trouble Lights
. Difficulty establishing a pilot arc may indicate consumables need to be cleaned or replaced.
Light
Power
Condition
Status/Possible Cause
On
Input power is okay.
Off
When Power light is on, system is normal if these lights
are off.
Power
Flashing rate is steady for 15 seconds or until torch trigger
is pressed again, whichever comes first.
Input power below 88 volts AC, but has returned to
normal.
Power
Repetitive flashing rate of two quick cycles, then a one
second pause.
Input power is below 88 volts AC.
Pressure
On
No or low [below 40 psi (276 kPa)] input pressure.
Pressure
Flashing rate is steady for 15 seconds or until torch trigger
is pressed again, whichever comes first.
Regulated pressure in the unit is low. Check torch for
leaks. Check input pressure to unit is between 90 to 120
psi (621 to 827 kPa).
Repetitive flashing rate of two quick cycles, then a one
second pause for a 15 second period.
Regulated pressure in the unit is high. Check input pressure
to unit is between 90 to 120 psi (621 to 827 kPa).
On
Torch cup is loose or off. Once cup is tightened, unit
power must be cycled off and back on again.
Cup
Flashing rate is steady for 15 seconds or until torch trigger
is pressed again, whichever comes first.
No arc was established. Check consumables or torch.
Cup
Repetitive flashing rate of two quick cycles, then a one
second pause for a 15 second period or until torch trigger
is pressed again, whichever comes first.
No pilot arc established possibly due to a loss of current.
Check consumables.
Cup
Repetitive flashing rate of three quick cycles, then a one
second pause for a 15 second period or until torch trigger
is pressed again, whichever comes first.
Consumables in torch failed to separate during pilot arc
possibly due to being stuck. Check consumables.
On
Power source overheated (see Section 4-5). Stop cutting
and allow unit to cool down.
On (indefinitely)
Power source temperature sensors may have failed or
ambient temperature is below -22°F (-30°C).
Flashing rate is steady (indefinitely).
Power source temperature sensor provided inaccurate
readings, but returned to normal. Unit power must be
cycled off and back on again.
Pressure/Cup/Temp
Pressure
Cup
Temperature
Temperature
Temperature
Stalled or locked fan. Clean or replace as needed.
For system troubleshooting see Section 7-8 and Section 7-9.
OM-253555 Page 30
. A complete Parts List is available at www.MillerWelds.com
7-8. Troubleshooting Power Source
Trouble
Remedy
No pilot arc; difficulty in establishing an Clean or replace worn consumables as necessary (see Section 7-6).
arc.
Check for damaged torch or torch cable.
No cutting output; Power light off; status Place Power switch in On position.
lights off; fan motor FM does not run.
Place line disconnect device in On position (see Section 5-9).
Check line fuse(s) and replace if needed or reset circuit breakers (see Section 5-9).
Pilot arc working; no cutting output; Be sure work clamp is connected.
Power light on; status lights off; fan
motor running.
Clean or replace worn consumables as necessary (see Section 7-6).
No gas/air flow; Power light on; status Have Factory Authorized Service Agent check for proper torch connections. Check operation of gas
lights off; fan motor running.
valve AS1, and check gas/air system for leaks. Check filter element (see Section 7-5).
Pressure status light On.
Check for sufficient gas/air supply pressure (see Section 5-2).
Check for dirty air filter and replace, if necessary (see Section 7-5).
Check air lines for leaks.
Have Factory Authorized Service Agent check pressure switch and control board.
Cup status light On.
Check torch shield cup (see Section 7-4). Reset power switch.
Have Factory Authorized Service Agent check torch.
Temperature status light On.
Unit overheating. Allow fan to run; the Trouble light goes out when the unit has cooled.
Have Factory Authorized Service Agent check control board.
Status lights not working.
Have Factory Authorized Service Agent check unit.
Power light flashing, status lights off.
Reset power switch. If problem continues, have qualified technician check input line power.
Pressure status light flashes.
Unit lost pressure (momentarily) while cutting. Check air line for leaks.
Cup status light flashes.
Unit lost output while attempting to cut or pilot. Check consumables and torch for wear.
Short tip life.
Check and clean drag shield of any slag, particles, and debris.
Check input air pressure.
7-9. Troubleshooting Torch
Trouble
Remedy
Arc goes on and off while cutting.
Torch travel speed too slow; increase travel speed (see Sections 6-4 and 6-5). Clean or replace torch
consumables as necessary (see Section 7-6). Be sure work clamp is securely attached to workpiece.
Arc goes out while cutting.
Be sure work clamp is securely attached to workpiece. Make sure tip is on or near [1/16 in. (1.6 mm) to
1/8 in. (3.2 mm)] workpiece (see Sections 6-4 and 6-5). Clean or replace torch consumables as necessary (see Section 7-6).
Sparks come out top of cut or cut is not Torch travel speed too fast; reduce travel speed (see Sections 6-4 and 6-5). Clean or replace torch conclean.
sumables as necessary (see Section 7-6). Be sure work clamp is securely attached to workpiece. Unit
not capable of cutting metals thicker than rating (see Section 6-2).
Trouble lights are on; unit has no cutting Check torch consumables. Check for gas/air flow at torch. Check air supply connection and pressure to
output.
unit and torch. Reset unit Power switch. Have Factory Authorized Service Agent check torch and
connections inside unit.
OM-253555 Page 31
SECTION 8 − ELECTRICAL DIAGRAM
Figure 8-1. Circuit Diagram
OM-253555 Page 32
265 469-A
OM-253555 Page 33
SECTION 9 − PARTS LIST
9-1. Recommended Spare Parts
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Recommended Spare Parts
................
................
................
................
................
................
................
................
225970
219261
219258
238486
249949
263799
253524
219259
. . Plug Kit, Adapter (115V/15A) (230V/50A) (Including) . . . . . . . . . . . . . . . . . . . . .
. . . Adapter, Power Cable 5−15P (115V/15A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . Adapter, Power Cable6−50P (230V/50A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Element, Filter Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . XT30, 12FT Hand Held (Replacement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cable, Work 12 ft 12 ga w/200A Clamp & Plug . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Label, XT30 Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Adapter, Power Cable 5-20P (115v/20A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
. A complete Parts List is available on-line at www.MillerWelds.com
2
1
3
4
5
6
7
Item
No.
Dia.
Mkgs.
Ref. 253 524-A
Figure 8-1. Consumable Parts For XT30 Torches
Part
No.
Description
Quantity
Figure 8-1. Consumable Parts For XT30 Torches
...
...
...
...
...
...
...
1
2
3
4
5
6
7
..........
..........
..........
..........
..........
..........
..........
249930
249932
249927
249931
249926
249969
249933
..
..
..
..
..
..
..
Drag Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Retaining Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Swirl Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O−Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Extended Consumable Shield Deflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. A complete Parts List is available on-line at www.MillerWelds.com
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-253555 Page 34
1
2
5
6
4
1
3
See Figure Figure 8-1 for
additional consumable parts.
Figure 8-2. Torch, XT30
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 8-2. Torch, XT30
... 1 ..........
... 2 ..........
... 3 ..........
... 4 ..........
... 5 ..........
... 6 ..........
................
................
259870
249971
249957
252938
249972
249973
252951
249949
..
..
..
..
..
..
..
..
Torch Handle Kit, XT30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Torch Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Leads, 12 ft XT30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Torch Body Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Torch Trigger Assembly w/Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cup Detect Switch w/Screws 30-60Amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grease, Silicone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Torch, Replacement 12 ft XT30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
. A complete Parts List is available on-line at www.MillerWelds.com
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-253555 Page 35
Notes
Work like a Pro!
Pros weld and cut
safely. Read the
safety rules at
the beginning
of this manual.
Notes
Notes
Effective January 1, 2016
(Equipment with a serial number preface of MG or newer)
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions below, 5. 6 Months — Parts
Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to its original
* Batteries
retail purchaser that new Miller equipment sold after the effective
* Bernard Guns (No Labor)
date of this limited warranty is free of defects in material and
* Tregaskiss Guns (No Labor)
workmanship at the time it is shipped by Miller. THIS WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS 6. 90 Days — Parts
* Accessory (Kits)
OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
* Canvas Covers
* Induction Heating Coils and Blankets, Cables, and
Within the warranty periods listed below, Miller will repair or replace
Non-Electronic Controls
any warranted parts or components that fail due to such defects in
* M-Guns
material or workmanship. Miller must be notified in writing within
thirty (30) days of such defect or failure, at which time Miller will
* MIG Guns and Subarc (SAW) Torches
provide instructions on the warranty claim procedures to be
* Remote Controls and RFCS-RJ45
followed. If notification is submitted as an online warranty claim, the
* Replacement Parts (No labor)
claim must include a detailed description of the fault and the
* Roughneck Guns
troubleshooting steps taken to identify failed components and the
* Spoolmate Spoolguns
cause of their failure.
Miller shall honor warranty claims on warranted equipment listed
below in the event of such a failure within the warranty time periods.
All warranty time periods start on the delivery date of the equipment
to the original end-user purchaser, and not to exceed twelve months
after the equipment is shipped to a North American distributor or
eighteen months after the equipment is shipped to an International
distributor.
1.
2.
3.
4.
5 Years Parts — 3 Years Labor
* Original Main Power Rectifiers Only to Include SCRs,
Diodes, and Discrete Rectifier Modules
3 Years — Parts and Labor
* Auto-Darkening Helmet Lenses (Except Classic
Series) (No Labor)
* Engine Driven Welder/Generators
(NOTE: Engines are Warranted Separately by the
Engine Manufacturer.)
* Inverter Power Sources (Unless Otherwise Stated)
* Plasma Arc Cutting Power Sources
* Process Controllers
* Semi-Automatic and Automatic Wire Feeders
* Transformer/Rectifier Power Sources
2 Years — Parts and Labor
* Auto-Darkening Helmet Lenses − Classic Series Only
(No Labor)
* Fume Extractors − Capture 5, Filtair 400 and Industrial
Collector Series
1 Year — Parts and Labor Unless Specified
* Automatic Motion Devices
* CoolBelt and CoolBand Blower Unit (No Labor)
* Desiccant Air Dryer System
* External Monitoring Equipment and Sensors
* Field Options
(NOTE: Field options are covered for the remaining
warranty period of the product they are installed in,
or for a minimum of one year — whichever is
greater.)
* RFCS Foot Controls (Except RFCS-RJ45)
* Fume Extractors − Filtair 130, MWX and SWX Series
* HF Units
* ICE/XT Plasma Cutting Torches (No Labor)
* Induction Heating Power Sources, Coolers
(NOTE: Digital Recorders are Warranted Separately
by the Manufacturer.)
* LiveArc Welding Performance Management System
* Load Banks
* Motor-Driven Guns (except Spoolmate Spoolguns)
* PAPR Blower Unit (No Labor)
* Positioners and Controllers
* Racks
* Running Gear/Trailers
* Spot Welders
* Subarc Wire Drive Assemblies
* Water Coolant Systems
* TIG Torches (No Labor)
* Wireless Remote Foot/Hand Controls and Receivers
* Work Stations/Weld Tables (No Labor)
Miller’s True Blue® Limited Warranty shall not apply to:
1.
2.
3.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, relays, work
station table tops and welding curtains, or parts that
fail due to normal wear. (Exception: brushes and
relays are covered on all engine-driven products.)
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable
and necessary maintenance, or equipment which has
been used for operation outside of the specifications for
the equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in appropriate
cases, (3) the reasonable cost of repair or replacement at an
authorized Miller service station; or (4) payment of or credit for the
purchase price (less reasonable depreciation based upon actual
use) upon return of the goods at customer’s risk and expense.
Miller’s option of repair or replacement will be F.O.B., Factory at
Appleton, Wisconsin, or F.O.B. at a Miller authorized service facility
as determined by Miller. Therefore no compensation or
reimbursement for transportation costs of any kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT),
WHETHER BASED ON CONTRACT, TORT OR ANY OTHER
LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY
IMPLIED WARRANTY, GUARANTY OR REPRESENTATION AS
TO PERFORMANCE, AND ANY REMEDY FOR BREACH OF
CONTRACT TORT OR ANY OTHER LEGAL THEORY WHICH,
BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION,
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF
DEALING, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT
FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED BY
MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein, and to
the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available, but
may vary from province to province.
miller_warr 2016-01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
For International Locations Visit
www.MillerWelds.com
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
ORIGINAL INSTRUCTIONS − PRINTED IN USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
© 2016 Miller Electric Mfg. Co.
2016−01