Miller | MG460083T | Owner Manual | Miller SPOOLMATIC 30A User manual

Miller SPOOLMATIC 30A User manual
OM-1213
137531AP
2016−10
Processes
MIG (GMAW) Welding
Description
Feeder Gun
R
Spoolmatic 15A
And 30A
For product information,
Owner’s Manual translations,
and more, visit
www.MillerWelds.com
File: MIG (GMAW)
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001 Quality System Warranty and service information for your
Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual specification sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 2009−09
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 −SAFETY PRECAUTIONS FOR GMAW WELDING GUNS − READ BEFORE USING . . . . . .
1
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1-3. Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1-4. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1-5. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
SECTION 2 − MESURES DE SÉCURITÉ VISANT LES PISTOLETS DE SOUDAGE GMAW − À LIRE AVANT
UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
2-1. Signification des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
2-3. Proposition californienne 65 Avertissements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
2-4. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
2-5. Informations relatives aux CEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
SECTION 3 − DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
3-1. Additional Safety Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
3-2. Miscellaneous Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
SECTION 4 − SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
4-1. Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
4-2. Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
SECTION 5 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
5-1. Removing Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
5-2. Installing Wire Spool And Threading Welding Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
5-3. Rotating Canister . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
5-4. Connecting To 24 Volt Weld Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
5-5. Connecting To 115 Volt Weld Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
5-6. Installing Gas Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
5-7. Adjusting Drive Roll And Spool Brake Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
SECTION 6 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
6-1. Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
6-2. Shielding Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
SECTION 7 − MAINTENANCE & TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
7-1. Changing Gun Contact Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
7-2. Replacing Head Tube Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
7-3. Gun Drive Assembly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
7-4. Replacing Canister Inlet Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
7-5. Replacing Spool Canister . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
7-6. Replacing Diffuser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
7-7. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
SECTION 8 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
SECTION 9 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
SECTION 10 − PARTS LIST INCLUDING CONSUMABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
WARRANTY
SECTION 1 −SAFETY PRECAUTIONS FOR GMAW
WELDING GUNS − READ BEFORE USING
SR7 (MIG) 2015-09
Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.
1-1. Symbol Usage
DANGER! − Indicates a hazardous situation which, if
not avoided, will result in death or serious injury. The
possible hazards are shown in the adjoining symbols
or explained in the text.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in the text.
NOTICE − Indicates statements not related to personal injury.
. Indicates special instructions.
This group of symbols means Warning! Watch Out! ELECTRIC
SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the
hazards.
1-2. Arc Welding Hazards
The symbols shown below are used throughout this manual
to call attention to and identify possible hazards. When you
see the symbol, watch out, and follow the related instructions
to avoid the hazard. The safety information given below is
only a summary of the more complete safety information
found in the welding power source Owner’s Manual. Read
and follow all Safety Standards.
BUILDUP OF GAS can injure or kill.
D Shut off compressed gas supply when not in
use.
D Always ventilate confined spaces or use approved air-supplied respirator.
Only qualified persons should install, operate, maintain, and
repair this unit.
During operation, keep everybody, especially children, away.
ELECTRIC SHOCK can kill.
D Always wear dry insulating gloves.
D Insulate yourself from work and ground.
D Do not touch live electrode or electrical parts.
D Replace worn, damaged, or cracked guns or cables.
D Turn off welding power source before changing contact tip or gun
parts.
D Keep all covers and handle securely in place.
FUMES AND GASES can be hazardous.
D Keep your head out of the fumes.
D Ventilate area, or use breathing device. The
recommended way to determine adequate
ventilation is to sample for the composition and quantity of fumes
and gases to which personnel are exposed.
D Read and understand the Safety Data Sheets (SDSs) and the
manufacturer’s instructions for adhesives, coatings, cleaners,
consumables, coolants, degreasers, fluxes, and metals.
WELDING can cause fire or explosion.
D Do not weld near flammable material.
D Do not weld on containers that have held combustibles, or on closed containers such as
tanks, drums, or pipes unless they are properly prepared according to AWS F4.1 and AWS A6.0 (see Safety Standards).
D Watch for fire; keep extinguisher nearby.
D Read and understand the Safety Data Sheets (SDSs) and the
manufacturer’s instructions for adhesives, coatings, cleaners,
consumables, coolants, degreasers, fluxes, and metals.
MOVING PARTS can injure.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear an approved welding helmet fitted with a proper shade of filter
lenses to protect your face and eyes from arc rays and sparks
when welding or watching (see ANSI Z49.1 and Z87.1 listed in
Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash,
glare and sparks; warn others not to watch the arc.
D Wear body protection made from durable, flame-resistant material
(leather, heavy cotton, wool). Body protection includes oil-free
clothing such as leather gloves, heavy shirt, cuffless trousers, high
shoes, and a cap.
HOT PARTS can burn.
D Allow gun to cool before touching.
D Do not touch hot metal.
D Protect hot metal from contact by others.
OM-1213 Page 1
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Check for noise level limits exceeding those
specified by OSHA.
D Use approved ear plugs or ear muffs if noise level is high.
D Warn others nearby about noise hazard.
WELDING WIRE can injure.
READ INSTRUCTIONS.
D Read and follow all labels and the Owner’s
Manual carefully before installing, operating, or
servicing unit. Read the safety information at
the beginning of the manual and in each
section.
D Use only genuine replacement parts from the manufacturer.
D Perform installation, maintenance, and service according to the
Owner’s Manuals, industry standards, and national, state, and
local codes.
D Keep hands and body away from gun tip when
trigger is pressed.
1-3. Proposition 65 Warnings
Welding or cutting equipment produces fumes or gases
which contain chemicals known to the State of California to
cause birth defects and, in some cases, cancer. (California
Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to
the state of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after use.
1-4. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Combustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:
www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5NS
(phone: 800-463-6727, website: www.csagroup.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org).
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
1-5. EMF Information
Electric current flowing through any conductor causes localized electric
and magnetic fields (EMF). The current from arc welding (and allied processes including spot welding, gouging, plasma arc cutting, and induction heating operations) creates an EMF field around the welding circuit.
EMF fields can interfere with some medical implants, e.g. pacemakers.
Protective measures for persons wearing medical implants have to be
taken. For example, restrict access for passers−by or conduct individual risk assessment for welders. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding
circuit:
1. Keep cables close together by twisting or taping them, or using a
cable cover.
2. Do not place your body between welding cables. Arrange cables
to one side and away from the operator.
OM-1213 Page 2
3. Do not coil or drape cables around your body.
4. Keep head and trunk as far away from the equipment in the
welding circuit as possible.
5. Connect work clamp to workpiece as close to the weld as
possible.
6. Do not work next to, sit or lean on the welding power source.
7. Do not weld whilst carrying the welding power source or wire
feeder.
About Implanted Medical Devices:
Implanted Medical Device wearers should consult their doctor and the
device manufacturer before performing or going near arc welding, spot
welding, gouging, plasma arc cutting, or induction heating operations.
If cleared by your doctor, then following the above procedures is recommended.
SECTION 2 − MESURES DE SÉCURITÉ VISANT LES
PISTOLETS DE SOUDAGE GMAW − À LIRE AVANT
UTILISATION
SR7(MIG)_2015−09 fre
Pour écarter les risques de blessure pour vous−même et pour autrui — lire, appliquer et ranger en lieu sûr ces consignes relatives
aux précautions de sécurité et au mode opératoire.
2-1. Signification des symboles
DANGER! − Indique une situation dangereuse qui si on
l’évite pas peut donner la mort ou des blessures graves.
Les dangers possibles sont montrés par les symboles
joints ou sont expliqués dans le texte.
Indique une situation dangereuse qui si on l’évite pas
peut donner la mort ou des blessures graves. Les dangers possibles sont montrés par les symboles joints ou
sont expliqués dans le texte.
AVIS − Indique des déclarations pas en relation avec des blessures
personnelles.
. Indique des instructions spécifiques.
Ce groupe de symboles veut dire Avertissement! Attention! DANGER
DE CHOC ELECTRIQUE, PIECES EN MOUVEMENT, et PIECES
CHAUDES. Consulter les symboles et les instructions ci-dessous y
afférant pour les actions nécessaires afin d’éviter le danger.
2-2. Dangers relatifs au soudage à l’arc
Les symboles présentés ci-après sont utilisés tout au long du
présent manuel pour attirer votre attention et identifier les risques de danger. Lorsque vous voyez un symbole, soyez vigilant et suivez les directives mentionnées afin d’éviter tout
danger. Les consignes de sécurité présentées ci-après ne
font que résumer l’information contenue dans les normes de
sécurité énumérées dans le manuel d’utilisation du poste de
soudage. Veuillez lire et respecter toutes ces normes de sécurité.
L’installation, l’utilisation, l’entretien et les réparations ne
doivent être confiés qu’à des personnes qualifiées.
Au cours de l’utilisation, tenir toute personne à l’écart et plus
particulièrement les enfants.
UN CHOC ÉLECTRIQUE peut tuer.
D Porter toujours des gants secs et isolants.
D S’isoler de la pièce et de la terre.
D Ne jamais toucher une électrode ou des pièces
électriques sous tension.
D Remplacer les pistolets ou câbles de soudage qui sont endommagés, usés ou craquelés.
D Mettre la soudeuse hors tension avant de remplacer un bec
contact ou des pièces de pistolet.
D S’assurer que tous les couvercles et poignées sont fermement
assujettis.
LES VAPEURS ET LES FUMÉES
peuvent être nocives.
D Éloigner sa tête des endroits renfermant des
vapeurs.
D Aérer la zone de travail ou porter un appareil respiratoire. Pour déterminer la bonne ventilation, il est recommandé de procéder à un
prélèvement pour la composition et la quantité de fumées et de gaz
auxquels est exposé le personnel.
D Lire et comprendre les fiches de données de sécurité et les instructions du fabricant concernant les adhésifs, les revêtements, les nettoyants, les consommables, les produits de refroidissement, les
dégraisseurs, les flux et les métaux.
LE SOUDAGE peut causer un incendie ou une explosion.
D Ne pas souder à proximité de matériaux inflammables.
D Ne pas effectuer le soudage sur des conteneurs fermés tels que
des réservoirs, tambours, ou conduites, à moins qu’ils n’aient été
préparés correctement conformément à AWS F4.1 et AWS A6.0
(voir les Normes de Sécurité).
D Prendre garde aux incendies et toujours avoir un extincteur à
proximité.
D Lire et comprendre les fiches de données de sécurité et les
instructions du fabricant concernant les adhésifs, les revêtements,
les nettoyants, les consommables, les produits de refroidissement,
les dégraisseurs, les flux et les métaux.
L’ACCUMULATION DE VAPEURS
peut causer des lésions ou la mort.
D Quand on n’utilise pas le gaz comprimé de protection, fermer le robinet de la bouteille.
D Assurer toujours la ventilation des zones fermées ou utiliser un
appareil respiratoire avec alimentation en air.
Les PIÈCES MOBILES peuvent
causer des blessures.
D Ne pas s’approcher des organes mobiles.
D Ne pas s’approcher des points de coincement
tels que des rouleaux de commande.
LE RAYONNEMENT DE L’ARC peut
brûler les yeux et la peau.
Le rayonnement de l’arc du procédé de soudage
génère des rayons visibles et invisibles intenses
(ultraviolets et infrarouges) susceptibles de provoquer des brûlures
dans les yeux et sur la peau. Des étincelles sont projetées pendant le
soudage.
D Porter un casque de soudage approuvé muni de verres filtrants
approprié pour protéger visage et yeux pendant le soudage
(voir ANSI Z49.1 et Z87.1 énuméré dans les normes de sécurité).
D Porter des lunettes de sécurité avec écrans latéraux même sous
votre casque.
D Avoir recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements les éblouissements
et les étincelles ; prévenir toute personne sur les lieux de ne pas
regarder l’arc.
D Porter un équipement de protection pour le corps fait d’un matériau
résistant et ignifuge (cuir, coton robuste, laine). La protection du
corps comporte des vêtements sans huile comme par ex. des
gants de cuir, une chemise solide, des pantalons sans revers, des
chaussures hautes et une casquette.
OM-1213 Page 3
LES PIÈCES CHAUDES peuvent
provoquer des brûlures.
LES FILS DE SOUDAGE peuvent
provoquer des blessures.
D Laisser refroidir le pistolet avant de le toucher.
D Ne pas toucher d’objets métalliques chauds.
D Abriter les objets métalliques contre tout
contact par les personnes à proximité.
D Éloigner les mains et le corps de la buse du
pistolet après avoir appuyé sur la gâchette.
LIRE LES INSTRUCTIONS.
Le BRUIT peut endommager l’ouie.
D Lire et appliquer les instructions sur les
étiquettes et le Mode d’emploi avant
l’installation, l’utilisation ou l’entretien de
l’appareil. Lire les informations de sécurité au
début du manuel et dans chaque section.
Le bruit des processus et des équipements peut
affecter l’ouïe.
D Vérifier si les niveaux de bruit excèdent les limites spécifiées par l’OSHA.
D Utiliser des bouche-oreilles ou des serre-tête antibruit approuvés si
le niveau de bruit est élevé.
D Avertir les personnes à proximité au sujet du danger inhérent au
bruit.
D N’utiliser que les pièces de rechange recommandées par le constructeur.
D Effectuer l’installation, l’entretien et toute intervention selon les
manuels d’utilisateurs, les normes nationales, provinciales et de
l’industrie, ainsi que les codes municipaux.
2-3. Proposition californienne 65 Avertissements
Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des
malformations congénitales et, dans certains cas, des
cancers. (Code de santé et de sécurité de Californie, chapitre
25249.5 et suivants)
Ce produit contient des éléments chimiques, dont le plomb,
reconnus par l’État de Californie pour leur caractère
cancérogène ainsi que provoquant des malformations
congénitales ou autres problèmes de procréation. Se laver
les mains après toute manipulation.
2-4. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
is available as a free download from the American Welding Society at
http://www.aws.org or purchased from Global Engineering Documents
(phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Safe Practices for the Preparation of Containers and Piping for Welding
and Cutting, American Welding Society Standard AWS F4.1, from Global Engineering Documents (phone: 1-877-413-5184, website: www.global.ihs.com).
Safe Practices for Welding and Cutting Containers that have Held Combustibles, American Welding Society Standard AWS A6.0, from Global
Engineering Documents (phone: 1-877-413-5184,
website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:
www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 14501 George Carter Way, Suite
103, Chantilly, VA 20151 (phone: 703-788-2700, website:
www.cganet.com).
Safety in Welding, Cutting, and Allied Processes, CSA Standard
W117.2, from Canadian Standards Association, Standards Sales, 5060
Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5NS
(phone: 800-463-6727, website: www.csagroup.org).
Safe Practice For Occupational And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute,
25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, website: www.ansi.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org).
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954
(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—
phone for Region 5, Chicago, is 312-353-2220, website:
www.osha.gov).
2-5. Informations relatives aux CEM
Le courant électrique qui traverse tout conducteur génère des champs
électromagnétiques (CEM) à certains endroits. Le courant de soudage
crée un CEM autour du circuit et du matériel de soudage. Le courant
issu d’un soudage à l’arc (et de procédés connexes, y compris le
soudage par points, le gougeage, le découpage plasma et les
opérations de chauffage par induction) crée un champ
électromagnétique (CEM) autour du circuit de soudage. Les champs
électromagnétiques produits peuvent causer interférence à certains
implants médicaux, p. ex. les stimulateurs cardiaques. Des mesures de
protection pour les porteurs d’implants médicaux doivent être prises:
Limiter par exemple tout accès aux passants ou procéder à une
évaluation des risques individuels pour les soudeurs. Tous les
soudeurs doivent appliquer les procédures suivantes pour minimiser
l’exposition aux CEM provenant du circuit de soudage:
1
2
Rassembler les câbles en les torsadant ou en les attachant avec
du ruban adhésif ou avec une housse.
Ne pas se tenir au milieu des câbles de soudage. Disposer les
câbles d’un côté et à distance de l’opérateur.
OM-1213 Page 4
3
Ne pas courber et ne pas entourer les câbles autour de votre
corps.
4
Maintenir la tête et le torse aussi loin que possible du matériel du
circuit de soudage.
5
Connecter la pince sur la pièce aussi près que possible de la
soudure.
6
Ne pas travailler à proximité d’une source de soudage, ni
s’asseoir ou se pencher dessus.
7
Ne pas souder tout en portant la source de soudage ou le
dévidoir.
En ce qui concerne les implants médicaux :
Les porteurs d’implants doivent d’abord consulter leur médecin avant
de s’approcher des opérations de soudage à l’arc, de soudage par
points, de gougeage, du coupage plasma ou de chauffage par
induction. Si le médecin approuve, il est recommandé de suivre les procédures précédentes.
SECTION 3 − DEFINITIONS
3-1. Additional Safety Symbols And Definitions
. Some symbols are found only on CE products.
Warning! Watch Out! There are possible hazards as shown by the symbols.
Safe1 2012−05
3-2. Miscellaneous Symbols And Definitions
. Some symbols are found only on CE products.
A
X
U1
Amperes
Duty Cycle
Primary Voltage
V
I2
U2
Volts
IP
Rated Welding
Current
Conventional
Load Voltage
Degree Of
Protection
Percent
I1
Primary Current
Notes
OM-1213 Page 5
SECTION 4 − SPECIFICATIONS
4-1. Unit Specifications
Wire Diameter
Range
.025 Thru 1/16 in.
(0.6 Thru 1.6 mm)
Aluminum Wire
.025 Thru .045 in.
(0.6 Thru 1.1 mm)
Hard Or Cored Wire
Approximate
Wire Feed
Range
70 To 875 ipm
(1.7 To 22.2
mpm)
Cooling
Method
Air Cooled
Maximum
Spool Size
4 in. (102 mm)
Diameter
Overall
Dimensions
Weld Circuit Rating
100 Volts, 200 Amperes,
100% Duty Cycle
Using Argon Shielding Gas
Length: 15-3/8 in.
(390 mm)
Width: 2-1/2 in.
(64 mm)
Height: 10-3/4 in.
(273 mm)
Weight
2.9 lb
(1.3 kg) Gun
Only
15A Model:
9 lb (4.1 kg)
Gun With Cable
30A Model:
14 lb (6.4 kg)
Gun With Cable
4-2. Environmental Specifications
A. IP Rating
IP Rating
IP23
This equipment is designed for outdoor use. It may be stored,
but is not intended to be used for welding outside during precipitation unless sheltered.
IP23 2014−06
SECTION 5 − INSTALLATION
. Use weld control or welding power source Owner’s Manual during gun installation. If contact tip, liner, and drive roll groove are not correct for wire
size and type, see Section 7 to change parts as needed. See Parts List for other available contact tips.
5-1. Removing Top Cover
1
Top Cover Triangular Boss
Push up on triangular boss to open
door. Door hinges on handle.
1
To open door fully, push up on door
until it clicks into position.
. If door is pushed too far it will
separate from handle. If this
happens the door can be reinstalled.
Push door back into original position to close.
150 882-G
OM-1213 Page 6
5-2. Installing Wire Spool And Threading Welding Wire
1
2
3
4
8
Top Cover
Canister
Canister Cover
Thumbscrew (Canister Cover)
Loosen thumbscrew and remove
cover.
7
5
Wire Spool
Loosen wire from spool, cut off bent
wire, and pull 6 in. (150 mm) of wire
off spool.
6
Pressure Roll Assembly
Lift arm and open pressure roll
assembly.
7
8
6
Canister Inlet Guide
Drive Roll Groove
. For wire sizes .035 in. (0.9 mm)
and smaller use small groove,
and .047 in. (1.2 mm) and 1/16
in (1.6 mm) use large groove.
2
1
9
10
Contact Tip
Thread wire through canister inlet
guide, along drive roll groove, and
out contact tip.
11
3
Install spool so wire feeds off
bottom.
10 Spool Brake Thumbnut
If necessary, turn thumbnut counterclockwise slightly to install spool.
11 Thumbscrew (Canister
Rotation)
Loosen thumbscrew to rotate canister (see Section 5-3).
5
4
Close and secure pressure roll
assembly.
Reinstall top cover and canister
cover.
9
Tools Needed:
150 436-F
5-3. Rotating Canister
1
1
Canister
Loosen canister rotation thumbscrew (see Section 5-2). Move canister to desired position. Tighten
thumbscrew.
Rear View
150 433-A
OM-1213 Page 7
5-4. Connecting To 24 Volt Weld Control
1
Gas Hose
Connect fitting to regulator/flowmeter (see Section 5-6).
1
4
3
2
2
3
24 Volt Weld Control
Trigger Control Cord
Insert plug into receptacle, and
tighten threaded collar.
4
Weld Cable
Connect to positive (+) weld output
terminal on welding power source
according to its Owner’s Manual.
Tools Needed:
1-1/8, 5/8 in.
150 917-G
5-5. Connecting To 115 Volt Weld Control
1
2
115 Volt Weld Control
Gas Hose
Connect to regulator/flowmeter.
3
Trigger Control Cord
Insert plug into receptacle, and
tighten threaded collar.
6
5
1
4
5
Weld Cable
Positive (+) Weld Output
Terminal In Control
Connect weld cable to positive (+)
weld output terminal in weld control.
Reinstall weld control wrapper.
3
Left Side
Wrapper Off
2
4
3
Tools Needed:
1-1/8, 5/8 in.
Ref. 149 549-A / 149 966-J
OM-1213 Page 8
5-6. Installing Gas Supply
Obtain gas cylinder and chain to
running gear, wall, or other stationary support so cylinder cannot fall
and break off valve.
1
2
Cap
Cylinder Valve
Remove cap, stand to side of valve,
and open valve slightly. Gas flow
blows dust and dirt from valve.
Close valve.
3
4
Cylinder
Regulator/Flowmeter
Install so face is vertical.
1
. Delivery pressure range must
not exceed 60 psi.
5
Gas Hose Connection
Fitting has
threads.
2
6
5/8-18
right-hand
Flow Adjust
Typical flow rate is 20 cfh (cubic feet
per hour). Check wire manufacturer’s recommended flow rate.
Make sure flow adjust is closed
when opening cylinder to avoid
damage to the flowmeter.
3
7
8
CO2 Adapter
O-Ring
Install adapter with O-ring between
regulator/flowmeter and
CO2
cylinder.
Argon Gas
6
OR
5
1
4
2
3
7
8
CO2 Gas
Tools Needed:
1-1/8, 5/8 in.
ssb3.1* 5/94 − 158 697-A
OM-1213 Page 9
5-7. Adjusting Drive Roll And Spool Brake Pressure
1
2
3
Top Cover
Canister Cover
Thumbscrew
Loosen thumbscrew and remove
cover.
4
Spool
Cut welding wire off at contact tip.
Retract wire onto spool and secure.
5
5
1
Spool Brake Thumbnut
Grasp spool in one hand and turn
while adjusting spool brake thumbnut. When a slight force is needed
to turn spool, tension is set. Do not
overtighten.
2
3
Reinstall canister cover. Thread
welding wire (see Section 5-2).
6
Drive Roll Tension Thumbnut
Turn On unit and check drive roll
pressure by feeding wire against a
wood board or concrete surface;
wire should feed steadily without
slipping.
Adjust drive roll tension thumbnut if
necessary. Do not overtighten.
4
Turn Off unit. Reinstall top cover.
6
Adjusting Pressure
WOOD
Tools Needed:
Ref. 151 112-F / 147 741-F
OM-1213 Page 10
SECTION 6 − OPERATION
6-1. Controls
1
Trigger
Press trigger to energize welding
power source contactor (if applicable), start shielding gas flow, and
begin wire feed.
For shielding gas preflow and postflow, lightly press trigger before and
after welding.
2
Wire Speed Control
Use control to adjust wire feed
speed. The numbers in the opening
are not a wire feed speed and are
for reference only.
1
2
Ref. 147 741-F
6-2. Shielding Gas
1
2
3
Shielding Gas Cylinder
Valve
Gun Trigger
Open valve on cylinder just before
welding.
Gun trigger turns weld output and
gas flow on and off. For shielding
gas preflow and postflow, lightly
press trigger before and after
welding.
2
1
Close valve on cylinder when finished welding.
3
sb5.1* 6/92 − S-0621-C / Ref. 147 741-F
OM-1213 Page 11
SECTION 7 − MAINTENANCE & TROUBLESHOOTING
!
n = Check
Z = Change
~ = Clean
* To be done by Factory Authorized Service Agent
Disconnect power
before maintaining.
. Maintain more often
during severe conditions.
l = Replace
Daily
n Check barrel clamp
screws for tightness.
l Repair Or Replace
Cracked Weld Cable
nl Gun Cables
~ Drive Rolls
~ Clean and Tighten
Weld Terminals
l Damaged Or Unreadable Labels
l Damaged Gas Hose
nl Cords
Every
Month
Every
3
Months
Every
6
Months
~ Blow out or Vacuum
Inside Unit
7-1. Changing Gun Contact Tip
Remove nozzle
1
Nozzle
2
FasTip
Unscrew FasTip.
Install new FasTip.
2
1
Ref. 150 437-A
OM-1213 Page 12
7-2. Replacing Head Tube Liner
The standard head tube liner will
accommodate wire diameters from
.030-1/16 wire size.
1
2
3
5
Cover
Screw
Clamp
Loosen clamp screws and remove
clamp.
4
Head Tube
Remove head tube from gun.
4
2
5
Liner
Pull liner out of head tube.
3
1
Insert liner into head tube and
reinstall head tube onto gun.
. A twisting motion may be need-
ed to feed liner thru head tube.
4
Tool Needed:
5/32 in.
Ref. 803 551-C
Notes
OM-1213 Page 13
7-3. Gun Drive Assembly Maintenance
Retract wire onto spool.
1
2
Setscrew
Current Pick-Up Tab
This tab helps prevent burnback
caused by welding arcs inside the
contact tip. This tab may be removed to provide an insulated drive
roll. (If tab is removed, a smaller diameter contact tip is recommended. See options in Parts List.)
Lightly grease top of tab before reinstalling.
3
3
Drive Roll
Use wire brush to clean drive roll.
Install drive roll with desired groove
down, and turn drive roll so one setscrew faces flat side of shaft.
1
2
4
Bearing
Use wire brush to clean bearing.
Line up drive roll groove with bearing groove and liner opening. Tighten setscrews.
Thread welding wire through gun
(see Section 5-2). Close and secure pressure roll assembly. Adjust
drive roll pressure, if necessary
(see Section 5-7). Reinstall top cover.
4
Tools Needed:
5/16 in.
Ref. 149 967-H / Ref. 800 945-A
OM-1213 Page 14
7-4. Replacing Canister Inlet Guide
1
2
Top Cover
Pressure Roll Assembly
Cut off welding wire where it enters
pressure roll assembly area.
3
1
Nozzle
Pull wire out nozzle.
7
6
4
5
5
2
4
Thumbscrew
Canister Cover
Loosen thumbscrew and remove
cover.
6
7
Wire Spool
Spool Brake Thumbnut
Loosen thumbnut, retract wire onto
spool, secure, and remove spool.
8
3
Canister Inlet Guide
Turn counterclockwise to remove.
Install new guide.
Reinstall spool and thread welding
wire (see Section 5-2).
Close pressure roll assembly. Adjust spool brake pressure and drive
roll pressure if necessary (see Section 5-7).
8
Reinstall covers.
Tools Needed:
Ref. 150 436-D / Ref. 149 967-H
7-5. Replacing Spool Canister
1
2
5
Top Cover
Pressure Roll Assembly
Cut off welding wire where it enters
pressure roll assembly area.
3
Nozzle
Pull wire out nozzle.
4
1
Thumbscrew (Canister
Rotation)
Turn thumbscrew counterclockwise three full turns.
5
4
3
Spool Canister
Remove as shown. Push new canister into wire drive housing until fully seated. Tighten thumbscrew.
2
Install spool and thread welding
wire (see Section 5-2).
Close pressure roll assembly. Adjust spool brake pressure and drive
roll pressure as necessary (see
Section 5-7).
Reinstall covers.
Tools Needed:
Ref. 149 967-H
OM-1213 Page 15
7-6. Replacing Diffuser
Turn Off welding power source.
1
Nozzle
2
FasTip
To remove, see Section 7-1.
3
Diffuser
Remove diffuser and replace.
3
2
1
Tools Needed:
3/8 in.
Ref. 803 348-G
7-7. Troubleshooting
Trouble
Remedy
No weld output; gun/feeder does not Secure weld control plug in 115 volts AC receptacle (see weld control Owner’s Manual).
work.
Place Power switch on welding power source in the On position (see welding power source Owner’s
Manual).
Erratic weld output.
Tighten and clean all connections.
Pressing gun/feeder trigger does not en- Secure plug from gun/feeder trigger cord into 10-socket receptacle on weld control (see Sections 5-4 and
ergize weld control; welding wire is not 5-5).
energized; shielding gas does not flow.
Wire feeds, shielding gas flows, but Secure control cable leads in weld control (see weld control Owner’s Manual).
welding wire is not energized.
See Troubleshooting section in welding power source Owner’s Manual.
Wire feeds erratically.
Check and correct drive roll pressure (see Section 5-7).
Clean drive roll or replace drive roll (see Section 7-3).
Decrease spool brake pressure (see Section 5-7).
OM-1213 Page 16
SECTION 8 − ELECTRICAL DIAGRAM
195 712-B
Figure 8-1. Circuit Diagram For Gun/Feeder
OM-1213 Page 17
OM-1213 Page 18
Figure 9-1. Complete Assembly
18
13
19
20
21
12
11
10
71
9
6
22
23
17
24
70
25
29
8
26
31
28
64**
27
30
32
63
65
33
34
33
66
36
35
37
62
61
60
43
42
41
38
44
69
58
57
56
40
39
68
59
46
45
55
47
48
13
49
50
51
52
54
53
not available unless listed.
7
3
5
. Hardware is common and
14
15
67
1
4
SECTION 9 − PARTS LIST
Ref. T0072-A
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Model
15A
30A
Figure 9-1. Complete Assembly
. . . 1 . . . . . . . . . . . . . . 214745 . . Cover (Included With Item 13) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 2 . . . . . . . . . . . . . . Deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 3 . . . . . . . . . . . . . . . M1570 . . Strain Relief, Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 4 . . . . . . . . . . . . . . 210417 . . Hose, Gas In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . . . . . . . . . 182824 . . Hose, Gas In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 5 . . . . . . . . . . . . . . . M1587 . . Cable, Control 15 Ft (Includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 5 . . . . . . . . . . . . . . . M1588 . . Cable, Control 30 Ft (Includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 6 . . . . R4 . . . . . . 200096 . . . . Potentiometer, C Sltd Sft 1/T .5W 10K Ohm . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 7 . . . PB1 . . . . . . 000369 . . . . Switch, Lim 10A 125/250VAC Dpst Plgr . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . 190294 . . . . Conn, Circ Ms/Cpc 10 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . 143922 . . . . Conn, Circ Cpc Clamp Str Rlf . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 8 . . . . . . . . . . . . . . 235689 . . Cable, Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 8 . . . . . . . . . . . . . . 235690 . . Cable, Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 9 . . . . . . . . . . . . . . 144861 . . Washer, Anti-turn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 10 . . . . . . . . . . . . . . 135127 . . Lock, Shaft Pot .250-32 X .125Dia Shaft . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 11 . . . . . . . . . . . . . . 134856 . . Knob, Speed Control 1-10 .140 Shaft X 1.125 Od . . . . . . . . . . . . . 1 . . . . 1
. . . 12 . . . . . . . . . . . . . . 602169 . . Screw, Set Stl Sch 8-32 X .187 Cup Pt . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 13 . . . . . . . . . . . . . . 220658 . . Case, Gun Lh/Rh (Molded Halves) . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 14 . . . . . . . . . . . . . . 183884 . . Spring, Cprsn .240 Od X .026 Wire X 1.000 . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 15 . . . . . . . . . . . . . . 184101 . . Washer, Shldr .140 Id X .250 Od . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 16 . . . . . . . . . . . . . . Deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 17 . . . . . . . . . . . . . . 231531 . . Head Tube Assy, Air Cooled Pistol (Includes) . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 18 . . . . . . . . . . . . . . 199613 . . . . Nozzle, Brass 5/8 In Orifice Tapered . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 19 . . . . . . . . . . . . . . . . . . . . . . . . . . Tip, Fastip (See Section 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 20 . . . . . . . . . . . . . . 227749 . . . . Diffuser, .281/.312 Od Collar Fastip 1/8 Rec . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 21 . . . . . . . . . . . . . . 232284 . . . . Insulator, Nozzle Collared Diffuser . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 22 . . . . . . . . . . . . . . 219794 . . . . Jacket, Outer Insulating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 23 . . . . . . . . . . . . . . 219795 . . . . Insulator, Barrel Pistol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 24 . . . . . . . . . . . . . . 219796 . . . . Head Tube, Air Pistol (Brazed) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 25 . . . . . . . . . . . . . . 134800 . . . . O-ring, .614 Id X .070Cs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 26 . . . . . . . . . . . . . . 212156 . . . . Liner, Phos Bronze .030-1/16 Wire X 7.313 . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 27 . . . . . . . . . . . . . . 133365 . . Clamp, Head Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 28 . . . . . . . . . . . . . . 000417 . . Screw, 10-24 X1.000Sochd Hex . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 29 . . . . . . . . . . . . . . 235225 . . Strip, Cop .010 X 1.500 X .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . 604638 . . Screw, 6-32 X .375Sochd Hex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 . . . . 3
. . . 30 . . . . . . . . . . . . . . 209342 . . Kit, Current Pick−up (Units W/Bearing Block) . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 31 . . . . . . . . . . . . . . 136135 . . Roll, Drive Vk Groove .023-1/16 Wire (Includes) . . . . . . . . . . . . . . 1 . . . . 1
. . . 31 . . . . . . . . . . . . . . 183357 . . Roll, Drive Vk Groove .030/.035 Wire (Includes) . . . . . . . . . . . . . . 1 . . . . 1
. . . 31 . . . . . . . . . . . . . . 183358 . . Roll, Drive Vk Groove .047/.062 Wire (Includes) . . . . . . . . . . . . . . 1 . . . . 1
. . . 32 . . . . . . . . . . . . . . 604612 . . . . Screw, Set Stl Sch 8-32 X .125 Cup Point . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 33 . . . . . . . . . . . . . . 206576 . . Screw, 006-32x .50 Btn Hd−Soc Stl Pld . . . . . . . . . . . . . . . . . . . . . 3 . . . . 3
. . . 34 . . . . . . . . . . . . . . 602198 . . Washer, Lock .141 Id Stl Split . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 35 . . . . . . . . . . . . . . 134624 . . Washer, Shldr.140Id 0.187odx.094T .375odx.031T Nyl . . . . . . . . 2 . . . . 2
. . . 36 . . . . . . . . . . . . . . 134623 . . Bearing, Idler Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 37 . . . . . . . . . . . . . . 132852 . . Arm, Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 38 . . . . . . . . . . . . . . 605798 . . Washer, Shldr Nyl .375 Od X .168 Id X .080 . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . 39 . . . . . . . . . . . . . . 133083 . . Spring, Tension Adj Drive Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 40 . . . . . . . . . . . . . . 144860 . . Screw, 8-32 X .437Flathd Slt Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 41 . . . . . . . . . . . . . . 058968 . . Ring, Retainer E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 42 . . . . . . . . . . . . . . 135474 . . Pin, Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 43 . . . . . . . . . . . . . . 155565 . . Screw, Thumb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . 134799 . . O-ring, .176 Id X .070Cs (Used W/Thumbscrew) . . . . . . . . . . . . . . 1 . . . . 1
. . . 44 . . . . . . . . . . . . . . 135126 . . Screw, Set 6-32 X .125 Cup Point Sch Stl . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 45 . . . . . . . . . . . . . . 602209 . . Washer, Tooth .256 Id Stl Intl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
OM-1213 Page 19
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 9-1. Complete Assembly (Continued)
. . . 46 . . . . . . . . . . . . . . 602154 . . Screw, .250-20 X .500Hexhd Stl Slffmg . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 47 . . . . . . . . . . . . . . 132527 . . Canister, Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 48 . . . . . . . . . . . . . . 148488 . . Post, Support Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 49 . . . . . . . . . . . . . . 132529 . . Pad, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 50 . . . . . . . . . . . . . . 148489 . . Washer, Anti-turn .380 Id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 51 . . . . . . . . . . . . . . 132524 . . Nut, .375-24 .56Knrl Alum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 52 . . . . . . . . . . . . . . 000364 . . Ring, Retainer Ext .145 Shaft Grv X .025Thk . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 53 . . . . . . . . . . . . . . 132526 . . Cover, Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 54 . . . . . . . . . . . . . . 132528 . . Screw, Thumb Canister . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 55 . . . . . . . . . . . . . . 269554 . . Guide, Inlet Canister . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 56 . . . . . . . . . . . . . . 112896 . . Spring, Cprsn .240 Od X .020 Wire X .437 . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 57 . . . . . . . . . . . . . . 135580 . . Fitting, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . . . . . . . . . . . . . . . . . 146555 . . Screw, Set 8-32 X .125 Cup Sch . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 58 . . . . . . . . . . . . . . 135773 . . Nut, 8-32 .56Knrl Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 59 . . . . . . . . . . . . . . 143360 . . Screw, 8-32 X .500Panhd Phl Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 60 . . . . . . . . . . . . . . 136679 . . Clamp, Strain Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 61 . . . . . . . . . . . . . . 129351 . . Screw, 8-32 X .500Hexwhd Slt Stl Slffmg . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 62 . . . . B2 . . . . . . 230947 . . Motor, Gear Pm 24 VDC 420 RPM 10.2:1 Ratio W/Conn . . . . . . 1 . . . . 1
. . . 63 . . . . . . . . . . . . . . 164592 . . Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 64 . . . . . . . . . . . . . . 236149 . . Kit, Replacement Drive Housing/Spool (Includes) . . . . . . . . . . . . . 1 . . . . 1
. . . 64 . . . . . . . . . . . . . . 239754 . . Kit, Housing W/Handles (Includes) . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 65 . . . . . . . . . . . . . . 058262 . . . . Cap, Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . 162038 . . . . Bearing, Ball Rdl Sgl Row 8mm X 16mm X 5mm Wide Sh . . . . 1 . . . . 1
. . . . . . . . . . . . . . . . . . . . 162039 . . . . Bushing, Nylatron .252id X .315 Od X .250 Lg .500 X . . . . . . . . 1 . . . . 1
. . . 66 . . . . . . . . . . . . . . . M1602 . . Ring, Valve Boot Retainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 67 . . . . . . . . . . . . . . 217934 . . Screw, K40x 20 Pan Hd−trx Stl Pld Pt Thread Forming . . . . . . . . 4 . . . . 4
. . . 68 . . . . . . . . . . . . . . 005464 . . Screw, Set 250−20x .37 Ovl Pt Sch Stl Pln Nylok . . . . . . . . . . . . . 1 . . . . 1
. . . 69 . . . . . . . . . . . . . . 235753 . . Ftg, Connection Power Weld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 70 . . . . . . . . . . . . . . 235751 . . Tubing, Silicone Rbr .500 Id X Spool Black . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . 71 . . . . . . . . . . . . . . . M1460 . . O-Ring, .143 Id X .349 Od X .103 Cs, Buna-N . . . . . . . . . . . . . . . . 1 . . . . 1
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1213 Page 20
SECTION 10 − PARTS LIST INCLUDING CONSUMABLES
Item
Number
1
2
3
4
5
.030−1/16” WIRE
STANDARD
INSULATOR
.030−1/16” WIRE
.035−1/16” WIRE
.030−1/16” WIRE
(231 512)
COLLARED
INSULATOR
(227 749)
(#232 284)
XR-A Spoolmatic
Barrel Assy
6.0” STRAIGHT
(#221 087)
(231 511)
TAPERED
INSULATOR
Ref. 803 909-A / 803 932 / 803 933 / 803 934
Figure 10-1. Consumables Flowchart
OM-1213 Page 21
Item
No.
Part
No.
Description
Quantity
Figure 10-1. Consumables Flowchart
Table 10-1. Nozzles
. . . 1 . . . . . . . . . ♦176238 . . Nozzle, Spot Flat (Requires Diffuser 209099, Used With Any
Heavy Duty FasTipt Contact Tip) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦176240 . . Nozzle, Spot Inside Corner (Requires Diffuser 209099, Used With Any
Heavy Duty FasTipt Contact Tip) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦176242 . . Nozzle, Spot Outside Corner (Requires Diffuser 209099, Used With Any
Heavy Duty FasTipt Contact Tip) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦199610 . . Nozzle, Screw On Brass 1/2 in Orifice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦199611 . . Nozzle, Screw On Brass 3/4 in Orifice Straight . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦199612 . . Nozzle, Screw On Brass 3/4 in Orifice Straight Heavy Duty . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦199613 . . Nozzle, Screw On Brass 5/8 in Orifice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦199614 . . Nozzle, Screw On Brass 5/8 in Orifice Heavy Duty . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦199615 . . Nozzle, Screw On Copper 1/2 in Orifice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦199616 . . Nozzle, Screw On Copper 3/4 in Orifice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦199617 . . Nozzle, Screw On Copper 3/4 in Orifice Heavy Duty . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . . 198855 . . Nozzle, Screw On Copper 5/8 in Orifice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . . 199618 . . Nozzle, Screw On Copper 5/8 in Orifice Heavy Duty . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦207313 . . Nozzle, Screw On Copper 5/8 in Orifice 15/16 OD . . . . . . . . . . . . . . . . . . . . . . .
. . . 1 . . . . . . . . . ♦209033 . . Nozzle, Slip On Copper 1/2 in Orifice Tapered (Requires Diffuser 209031 Or
209032 And Insulator 209047, Used With Any Tapered FasTipt Contact Tip)
. . . 1 . . . . . . . . . ♦209034 . . Nozzle, Slip On Copper 3/8 in Orifice Tapered (Requires Diffuser 209031 Or
209032 And Insulator 209047, Used With Any Tapered FasTipt Contact Tip)
. . . 1 . . . . . . . . . ♦209035 . . Nozzle, Screw On Copper 3/8 in Orifice Tapered (Requires Diffuser 227 747,
231 511 Or 231 512, Used With Any Tapered FasTipt Contact Tip) . . . . . . .
. . . 1 . . . . . . . . . ♦209036 . . Nozzle, Screw On Copper 1/2 in Orifice Tapered (Requires Diffuser 227 747,
231 511 Or 231 512, Used With Any Tapered FasTipt Contact Tip) . . . . . . .
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Table 10-2. Heavy Duty FasTiptContact Tips*
...
...
...
...
...
...
...
2
2
2
2
2
2
2
. . . . . . . . . ♦206185
. . . . . . . . . ♦206186
. . . . . . . . . ♦206187
. . . . . . . . . . 206188
. . . . . . . . . ♦206189
. . . . . . . . . . 206190
. . . . . . . . . ♦206191
..
..
..
..
..
..
..
.030 in (0.8 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.035 in (0.9 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.040 in (1.0 mm) or .035 in (0.9 mm) Aluminum Wire . . . . . . . . . . . . . . . . . . . . .
.045 in (1.2 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.052 in (1.3 mm) or 3/64 in (1.2 mm) Aluminum Wire . . . . . . . . . . . . . . . . . . . . .
1/16 in (1.6 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.068 in (1.7 mm) or 1/16 in (1.6 mm) Aluminum Wire . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
Table 10-3. Extra Heavy Duty FasTiptContact Tips*
...
...
...
...
...
...
2
2
2
2
2
2
.........
.........
.........
.........
.........
.........
♦199605
♦199606
♦198851
♦198852
♦198853
♦198854
..
..
..
..
..
..
.035 in (0.9 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.040 in (1.0 mm) or .035 in (0.9 mm) Aluminum . . . . . . . . . . . . . . . . . . . . . . . . .
.045 in (1.2 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.052 in (1.3 mm) or 3/64 in (1.2 mm) Aluminum Wire . . . . . . . . . . . . . . . . . . . . .
1/16 in (1.6 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.068 in (1.7 mm) or 1/16 in (1.6 mm) Aluminum Wire . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
Table 10-4. Tapered FasTipt Contact Tips*
...
...
...
...
...
...
2
2
2
2
2
2
.........
.........
.........
.........
.........
.........
OM-1213 Page 22
♦209025
♦209026
♦209027
♦209028
♦209029
♦209030
..
..
..
..
..
..
.030 in (0.8 mm)
.035 in (0.9 mm)
.045 in (1.2 mm)
3/64 in (1.2 mm)
.052 in (1.3 mm)
1/16 in (1.6 mm)
....................................................
....................................................
....................................................
....................................................
....................................................
....................................................
1
1
1
1
1
1
Item
No.
Part
No.
Description
Quantity
Figure 10-1. Consumables Flowchart (Continued)
Table 10-5. Value Multi−Turn Contact Tips*
...
...
...
...
...
...
...
2
2
2
2
2
2
2
.........
.........
.........
.........
.........
.........
.........
♦071825
♦054202
♦054201
♦199593
♦044006
♦047566
♦202933
..
..
..
..
..
..
..
.030 in (0.9 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.035 in (0.9 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.045 in (1.2 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.3/64 in (1.2 mm) Aluminum Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.052 in (1.3 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1/16 in (1.6 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1/16 in (1.6 mm) Aluminum Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
Table 10-6. Gas Diffusers
...
...
...
...
...
3
3
3
3
3
. . . . . . . . . ♦198857
. . . . . . . . . ♦199623
. . . . . . . . . ♦199621
. . . . . . . . . ♦199622
. . . . . . . . . . 227749
..
..
..
..
..
. . . 3 . . . . . . . . . ♦231511 . .
. . . 3 . . . . . . . . . ♦231512 . .
. . . 3 . . . . . . . . . ♦209031 . .
. . . 3 . . . . . . . . . ♦209032 . .
. . . 3 . . . . . . . . . ♦209099 . .
1/8 in Tip Recess − For Extra Heavy Duty FasTip Contact Tips . . . . . . . . . . . .
Flush Tip − For Extra Heavy Duty FasTip Contact Tips . . . . . . . . . . . . . . . . . . .
1/8 in Tip Recess − For Value Multi−Turn Contact Tips . . . . . . . . . . . . . . . . . . .
Flush Tip − For Value Multi−Turn Contact Tips . . . . . . . . . . . . . . . . . . . . . . . . . .
1/8 in Tip Recess − For Heavy Duty FasTip Contact Tips
(Standard On All Guns) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1/4 in Tip Recess − For Heavy Duty FasTip Contact Tips . . . . . . . . . . . . . . . . .
Flush Tip − For Heavy Duty FasTip Contact Tips . . . . . . . . . . . . . . . . . . . . . . . .
Slip On Recessed Diffuser (Requires Nozzle 209033 Or 209034
And Insulator 209047, Used With Any Tapered FasTip Contact Tip) . . . . . . . .
Slip On Flush Diffuser (Requires Nozzle 209033 Or 209034
And Insulator 209047, Used With Any Tapered FasTip Contact Tip) . . . . . . . .
Spot Diffuser (Requires Spot Nozzle 176238 Or 176240 Or 176242) . . . . . . .
1
1
1
1
1
1
1
1
1
1
Table 10-7. Insulators
. . . 4 . . . . . . . . . . 232284 . . Insulator, Nozzle Collared Diffuser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . . . . . 198856 . . Insulator, Rubber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . . . . . 209047 . . Insulator, Teflon (Required When Using Diffuser 209031 Or 209032
With Nozzle 209033 Or 209034) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 10-8. Barrel Assemblies
. . . 5 . . . . . . . . . . 221087 . . Barrel Assy, Air Cooled Pistol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 10-9. Head Tube Assemblies
. . . . . . . . . . . . . . . . 231523 . . Kit, Head Tube Assy Air Cooled Pistol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
♦OPTIONAL
*All contact tips are packaged in bags of 25.
BE SURE TO PROVIDE MODEL WHEN ORDERING REPLACEMENT PARTS.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model is required when ordering parts from your local distributor.
OM-1213 Page 23
Notes
SOCKET/WRENCH SELECTION TABLE
(U.S. STANDARD)
Specifications
Socket or Wrench Size
SOCKET/WRENCH SELECTION TABLE
(METRIC)
Specifications
Socket or Wrench Size
Bolt
Diameter
Decimal
Equivalent
Bolt
Nut
Bolt
Diameter
U.S.
Decimal
Equivalent
Bolt
Nut
1/4 in.
.250 in.
3/8 in.
7/16 in.
6 mm
.2362 in.
10 mm
10 mm
5/16 in.
.3125 in.
1/2 in.
9/16 in.
8 mm
.3150 in.
14 mm
14 mm
3/8 in.
.375 in.
9/16 in.
5/8 in.
10 mm
.3937 in.
17 mm
17 mm
7/16 in.
.4375 in.
5/8 in.
3/4 in.
12 mm
.4724 in.
19 mm
19 mm
1/2 in.
.500 in.
3/4 in.
13/16 in.
14 mm
.5512 in.
22 mm
22 mm
9/16 in.
.5625 in.
7/8 in.
7/8 in.
16 mm
.6299 in.
24 mm
24 mm
5/8 in.
.625 in.
15/16 in.
1 in.
18 mm
.7087 in.
27 mm
27 mm
3/4 in.
.750 in.
1-1/8 in.
1-1/8 in.
22 mm
.8661 in.
32 mm
32 mm
7/8 in.
.875 in.
1-5/16 in.
1-5/16 in.
24 mm
.9449 in.
36 mm
36 mm
1 in.
1.000 in.
1-1/2 in.
1-1/2 in.
Notes
Notes
MATERIAL THICKNESS REFERENCE CHART
24 Gauge (.025 in.)
22 Gauge (.031 in.)
20 Gauge (.037 in.)
18 Gauge (.050 in.)
16 Gauge (.063 in.)
14 Gauge (.078 in.)
1/8 in. (.125 in.)
3/16 in. (.188 in.)
1/4 in. (.25 in.)
5/16 in. (.313 in.)
3/8 in. (.375 in.)
1/2 in. (.5 in.)
Effective January 1, 2016
(Equipment with a serial number preface of MG or newer)
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions below, 5. 6 Months — Parts
Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to its original
* Batteries
retail purchaser that new Miller equipment sold after the effective
* Bernard Guns (No Labor)
date of this limited warranty is free of defects in material and
* Tregaskiss Guns (No Labor)
workmanship at the time it is shipped by Miller. THIS WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS 6. 90 Days — Parts
* Accessory (Kits)
OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
* Canvas Covers
* Induction Heating Coils and Blankets, Cables, and
Within the warranty periods listed below, Miller will repair or replace
Non-Electronic Controls
any warranted parts or components that fail due to such defects in
* M-Guns
material or workmanship. Miller must be notified in writing within
thirty (30) days of such defect or failure, at which time Miller will
* MIG Guns and Subarc (SAW) Torches
provide instructions on the warranty claim procedures to be
* Remote Controls and RFCS-RJ45
followed. If notification is submitted as an online warranty claim, the
* Replacement Parts (No labor)
claim must include a detailed description of the fault and the
* Roughneck Guns
troubleshooting steps taken to identify failed components and the
* Spoolmate Spoolguns
cause of their failure.
Miller shall honor warranty claims on warranted equipment listed
below in the event of such a failure within the warranty time periods.
All warranty time periods start on the delivery date of the equipment
to the original end-user purchaser, and not to exceed twelve months
after the equipment is shipped to a North American distributor or
eighteen months after the equipment is shipped to an International
distributor.
1.
2.
3.
4.
5 Years Parts — 3 Years Labor
* Original Main Power Rectifiers Only to Include SCRs,
Diodes, and Discrete Rectifier Modules
3 Years — Parts and Labor
* Auto-Darkening Helmet Lenses (Except Classic
Series) (No Labor)
* Engine Driven Welder/Generators
(NOTE: Engines are Warranted Separately by the
Engine Manufacturer.)
* Inverter Power Sources (Unless Otherwise Stated)
* Plasma Arc Cutting Power Sources
* Process Controllers
* Semi-Automatic and Automatic Wire Feeders
* Transformer/Rectifier Power Sources
2 Years — Parts and Labor
* Auto-Darkening Helmet Lenses − Classic Series Only
(No Labor)
* Fume Extractors − Capture 5, Filtair 400 and Industrial
Collector Series
1 Year — Parts and Labor Unless Specified
* Automatic Motion Devices
* CoolBelt and CoolBand Blower Unit (No Labor)
* Desiccant Air Dryer System
* External Monitoring Equipment and Sensors
* Field Options
(NOTE: Field options are covered for the remaining
warranty period of the product they are installed in,
or for a minimum of one year — whichever is
greater.)
* RFCS Foot Controls (Except RFCS-RJ45)
* Fume Extractors − Filtair 130, MWX and SWX Series
* HF Units
* ICE/XT Plasma Cutting Torches (No Labor)
* Induction Heating Power Sources, Coolers
(NOTE: Digital Recorders are Warranted Separately
by the Manufacturer.)
* LiveArc Welding Performance Management System
* Load Banks
* Motor-Driven Guns (except Spoolmate Spoolguns)
* PAPR Blower Unit (No Labor)
* Positioners and Controllers
* Racks
* Running Gear/Trailers
* Spot Welders
* Subarc Wire Drive Assemblies
* Water Coolant Systems
* TIG Torches (No Labor)
* Wireless Remote Foot/Hand Controls and Receivers
* Work Stations/Weld Tables (No Labor)
Miller’s True Blue® Limited Warranty shall not apply to:
1.
2.
3.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, relays, work
station table tops and welding curtains, or parts that
fail due to normal wear. (Exception: brushes and
relays are covered on all engine-driven products.)
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable
and necessary maintenance, or equipment which has
been used for operation outside of the specifications for
the equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in appropriate
cases, (3) the reasonable cost of repair or replacement at an
authorized Miller service station; or (4) payment of or credit for the
purchase price (less reasonable depreciation based upon actual
use) upon return of the goods at customer’s risk and expense.
Miller’s option of repair or replacement will be F.O.B., Factory at
Appleton, Wisconsin, or F.O.B. at a Miller authorized service facility
as determined by Miller. Therefore no compensation or
reimbursement for transportation costs of any kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT),
WHETHER BASED ON CONTRACT, TORT OR ANY OTHER
LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY
IMPLIED WARRANTY, GUARANTY OR REPRESENTATION AS
TO PERFORMANCE, AND ANY REMEDY FOR BREACH OF
CONTRACT TORT OR ANY OTHER LEGAL THEORY WHICH,
BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION,
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF
DEALING, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT
FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED BY
MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein, and to
the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available, but
may vary from province to province.
miller_warr 2016-01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
For International Locations Visit
www.MillerWelds.com
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
ORIGINAL INSTRUCTIONS − PRINTED IN USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
© 2016 Miller Electric Mfg. Co.
2016−01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising