Miller | LE205948 | Owner Manual | Miller SS-74DX SWINGARC User manual

Miller SS-74DX SWINGARC User manual
OM-1500-12
207 751E
May 2004
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
(Gas-and Self-Shielding)
Submerged (SAW) Welding
Description
Wire Feeder
(Use with CV Power Sources)
SS-74DX Swingarc

SS-74DX12 and SS-74DX16
Visit our website at
www.MillerWelds.com
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001:2000 Quality Warranty and service information for your
System Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual catalog sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 7/03
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − À LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Signification des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien de l’appareil. . . . . . . . . . . .
2-4. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Information sur les champs électromagnétiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Installing Swivel Into Pipe Post . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Adjusting Control Tilt Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Installing Boom And Reel Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Installing Wire Guide Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Equipment Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. Control Box Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. 14-Pin Plug Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8. Removing Safety Collar And Adjusting Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9. Gun Recommendation Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10. Wire Type, Size, And Feed Speed Capability Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-11. Installing And Threading Welding Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-12. Setting Internal DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-13. Power Source Selection Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Operational Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Program Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Upper Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6. Lower Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Setup Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8. Adjust Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-9. Sequence Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-10. Auxiliary Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-11. Jog/Purge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − SETTING SEQUENCE PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Sequence Parameters In A Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − SETTING DUAL SCHEDULE PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Optional Dual Schedule Switch Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2. Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-3. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONS AND ACCESSORIES
WARRANTY
1
1
1
3
3
4
4
5
5
5
7
8
8
9
9
9
9
10
10
11
11
12
12
13
13
13
14
15
16
17
17
17
17
18
19
20
20
21
21
22
24
25
25
26
26
26
26
27
28
29
30
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som _8/03
1-1. Symbol Usage
Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.
Y Marks a special safety message.
. Means “Note”; not safety related.
This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.
1-2. Arc Welding Hazards
Y The symbols shown below are used throughout this manual to
call attention to and identify possible hazards. When you see
the symbol, watch out, and follow the related instructions to
avoid the hazard. The safety information given below is only
a summary of the more complete safety information found in
the Safety Standards listed in Section 1-5. Read and follow all
Safety Standards.
D If earth grounding of the workpiece is required, ground it directly
with a separate cable.
Y Only qualified persons should install, operate, maintain, and
repair this unit.
D Wear a safety harness if working above floor level.
D Keep all panels and covers securely in place.
Y During operation, keep everybody, especially children, away.
D Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic wire welding, the
wire, wire reel, drive roll housing, and all metal parts touching the
welding wire are electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
D Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
D Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
D Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
D Do not connect more than one electrode or work cable to any
single weld output terminal.
SIGNIFICANT DC VOLTAGE exists after removal of
input power on inverters.
D Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
D Do not touch live electrical parts.
D Wear dry, hole-free insulating gloves and body protection.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
D Use AC output ONLY if required for the welding process.
D If AC output is required, use remote output control if present on
unit.
D Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
D Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
D Keep your head out of the fumes. Do not breathe the fumes.
D Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
D When making input connections, attach proper grounding conductor first − double-check connections.
D Frequently inspect input power cord for damage or bare wiring −
replace cord immediately if damaged − bare wiring can kill.
D Turn off all equipment when not in use.
D Do not use worn, damaged, undersized, or poorly spliced cables.
D Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
D Do not drape cables over your body.
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D If inside, ventilate the area and/or use exhaust at the arc to remove
welding fumes and gases.
D If ventilation is poor, use an approved air-supplied respirator.
D Read the Material Safety Data Sheets (MSDSs) and the
manufacturer’s instructions for metals, consumables, coatings,
cleaners, and degreasers.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and if necessary, while wearing an
air-supplied respirator. The coatings and any metals containing
these elements can give off toxic fumes if welded.
OM-1500-12 Page 1
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear a welding helmet fitted with a proper shade of filter to protect
your face and eyes when welding or watching (see ANSI Z49.1
and Z87.1 listed in Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash and
glare; warn others not to watch the arc.
D Wear protective clothing made from durable, flame-resistant material (leather and wool) and foot protection.
BUILDUP OF GAS can injure or kill.
D Shut off shielding gas supply when not in use.
D Always ventilate confined spaces or use
approved air-supplied respirator.
HOT PARTS can cause severe burns.
D Do not touch hot parts bare handed.
D Allow cooling period before working on gun or
torch.
MAGNETIC FIELDS can affect pacemakers.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
D Protect yourself and others from flying sparks and hot metal.
D Do not weld where flying sparks can strike flammable material.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock and fire hazards.
D Do not use welder to thaw frozen pipes.
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
D Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
FLYING METAL can injure eyes.
D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
D Wear approved safety glasses with side
shields even under your welding helmet.
OM-1500-12 Page 2
D Pacemaker wearers keep away.
D Wearers should consult their doctor before
going near arc welding, gouging, or spot
welding operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Wear approved ear protection if noise level is
high.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D Protect compressed gas cylinders from excessive heat, mechanical shocks, slag, open flames, sparks, and arcs.
D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Keep cylinders away from any welding or other electrical circuits.
D Never drape a welding torch over a gas cylinder.
D Never allow a welding electrode to touch any cylinder.
D Never weld on a pressurized cylinder − explosion will result.
D Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and
associated parts in good condition.
D Turn face away from valve outlet when opening cylinder valve.
D Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D Read and follow instructions on compressed gas cylinders,
associated equipment, and CGA publication P-1 listed in Safety
Standards.
1-3. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
MOVING PARTS can cause injury.
D Do not install or place unit on, over, or near
combustible surfaces.
D Do not install unit near flammables.
D Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
FALLING UNIT can cause injury.
H.F. RADIATION can cause interference.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are
long enough to extend beyond opposite side of
unit.
D
OVERUSE can cause OVERHEATING
D
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
D
D
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
STATIC (ESD) can damage PC boards.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
ARC WELDING can cause interference.
MOVING PARTS can cause injury.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
D
D
WELDING WIRE can cause injury.
D Do not press gun trigger until instructed to do
so.
D Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
D
D
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
1-4. California Proposition 65 Warnings
Y Welding or cutting equipment produces fumes or gases which
contain chemicals known to the State of California to cause
birth defects and, in some cases, cancer. (California Health &
Safety Code Section 25249.5 et seq.)
For Gasoline Engines:
Y Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive
harm.
Y Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
For Diesel Engines:
Y Diesel engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects, and
other reproductive harm.
OM-1500-12 Page 3
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
(phone: 305-443-9353, website: www.aws.org).
Boulevard, Rexdale, Ontario, Canada M9W 1R3 (phone:
800−463−6727 or in Toronto 416−747−4044, website: www.csa−international.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126 (phone: 305-443-9353, website: www.aws.org).
Practice For Occupational And Educational Eye And Face Protection,
ANSI Standard Z87.1, from American National Standards Institute, 11
West 42nd Street, New York, NY 10036−8002 (phone: 212−642−4900,
website: www.ansi.org).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269−9101 (phone: 617−770−3000, website: www.nfpa.org and www.
sparky.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (phone:
617−770−3000,website: www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1735 Jefferson Davis Highway,
Suite 1004, Arlington, VA 22202−4102 (phone: 703−412−0900, website: www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there
are 10 Regional Offices−−phone for Region 5, Chicago, is
312−353−2220,website: www.osha.gov).
1-6. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
To reduce magnetic fields in the workplace, use the following
procedures:
OM-1500-12 Page 4
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from operator as practical.
5. Connect work clamp to workpiece as close to the weld as possible.
About Pacemakers:
Pacemaker wearers consult your doctor first. If cleared by your doctor,
then following the above procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − À LIRE AVANT
UTILISATION
som_fre 8/03
2-1. Signification des symboles
Signifie « Mise en garde. Faire preuve de vigilance. »
Cette procédure présente des risques identifiés par les
symboles adjacents aux directives.
Y Identifie un message de sécurité particulier.
. Signifie « NOTA » ; n’est pas relatif à la sécurité.
Ce groupe de symboles signifie « Mise en garde. Faire preuve de vigilance. » Il y a des dangers liés aux CHOCS ÉLECTRIQUES, aux
PIÈCES EN MOUVEMENT et aux PIÈCES CHAUDES. Se reporter
aux symboles et aux directives ci-dessous afin de connaître les mesures à prendre pour éviter tout danger.
2-2. Dangers relatifs au soudage à l’arc
Y Les symboles ci-après sont utilisés tout au long du présent
manuel pour attirer l’attention sur les dangers potentiels et les
identifier. Lorsqu’on voit un symbole, faire preuve de vigilance et
suivre les directives mentionnées afin d’éviter tout danger. Les
consignes de sécurité énoncées ci-après ne font que résumer le
contenu des normes de sécurité mentionnées à la section 2-4.
Lire et respecter toutes ces normes.
D N’utiliser que du matériel en bon état. Réparer ou remplacer sur−le−
champ les pièces endommagées. Entretenir l’appareil conformément
au présent manuel.
Y L’installation, l’utilisation, l’entretien et les réparations ne doivent être confiés qu’à des personnes qualifiées.
D Fixer le câble de retour de façon à obtenir un bon contact métal sur
métal avec la pièce à souder ou la table de travail, le plus près possible
de la soudure.
Y Pendant l’utilisation de l’appareil, tenir à l’écart toute personne,
en particulier les enfants.
D Porter un harnais de sécurité quand on travaille en hauteur.
D Maintenir solidement en place tous les panneaux et capots.
D
Ne pas connecter plus d’une électrode ou plus d’un câble de masse à un
même terminal de sortie.
LES DÉCHARGES ÉLECTRIQUES
peuvent être mortelles.
Un simple contact avec des pièces sous tension peut
causer une électrocution ou des blessures graves.
L’électrode et le circuit de soudage sont sous tension
dès que l’appareil est en fonctionnement. Le circuit
d’entrée et les circuits internes de l’appareil sont également sous tension.
En soudage semi−automatique ou automatique, le fil, le dévidoir, le
logement des galets d’entraînement et les pièces métalliques en contact
avec le fil de soudage sont sous tension. Tout matériel mal installé ou mal
mis à la terre présente un danger.
D Ne jamais toucher aux pièces électriques sous tension.
D Porter des gants et des vêtements de protection secs et exempts de
trous.
D S’isoler de la pièce et de la terre au moyen de tapis ou autres dispositifs isolants suffisamment grands pour empêcher tout contact
physique avec la pièce ou la terre.
D
D
D
Ne pas se servir d’une source de courant alternatif dans les zones humides, les endroits confinés ou là où on risque de tomber.
Ne se servir d’une source de courant alternatif QUE si le procédé de soudage l’exige.
Si l’utilisation d’une source de courant alternatif s’avère nécessaire, se servir de la fonction de télécommande si l’appareil en est équipé.
D Couper l’alimentation ou arrêter le moteur avant de procéder à l’installation, à la réparation ou à l’entretien de l’appareil. Couper/étiqueter
l’alimentation selon la norme OSHA 29 CFR 1910.147 (voir les normes de sécurité).
D Installer et mettre à la terre correctement l’appareil conformément à
son manuel d’utilisation et aux codes nationaux, provinciaux et
municipaux.
D Toujours vérifier la terre du cordon d’alimentation − Vérifier et s’assurer que le fil de terre du cordon d’alimentation est bien raccordé à la
borne de terre du sectionneur ou que la fiche du cordon est raccordée
à une prise correctement mise à la terre.
D Pour exécuter les branchements d’entrée, fixer d’abord le conducteur
de mise à la terre adéquat et contre−vérifier les connexions.
D Vérifier fréquemment le cordon d’alimentation et s’assurer qu’il n’est
ni endommagé ni dénudé ; le remplacer immédiatement s’il est endommagé − tout câble dénudé peut causer une électrocution.
D Mettre l’appareil hors tension quand on ne l’utilise pas.
D Ne pas utiliser de câbles usés, endommagés, de calibre insuffisant ou
mal épissés.
D Ne pas s’enrouler les câbles autour du corps.
D Si la pièce soudée doit être mise à la terre, le faire directement avec un
câble distinct.
D Ne pas toucher l’électrode quand on est en contact avec la pièce, la
terre ou une électrode d’une autre machine.
Il subsiste un COURANT CONTINU IMPORTANT
dans les convertisseurs après la suppression de
l’alimentation électrique.
D Arrêter les convertisseurs, débrancher le courant électrique et décharger les condensateurs d’alimentation selon les instructions
énoncées à la section Entretien avant de toucher les pièces.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
Le soudage génère des fumées et des gaz dont
l’inhalation peut être dangereuse pour la santé.
D Se tenir à distance des fumées et ne pas les inhaler.
D À l’intérieur, ventiler la zone et/ou utiliser un dispositif d’aspiration au
niveau de l’arc pour l’évacuation des fumées et des gaz de soudage.
D Si la ventilation est insuffisante, utiliser un respirateur à adduction
d’air agréé.
D Lire les fiches techniques de santé−sécurité (FTSS) et les instructions du fabricant concernant les métaux, les consommables, les
revêtements, les nettoyants et les dégraisseurs.
D Ne travailler dans un espace clos que s’il est bien ventilé ou porter un
respirateur à adduction d’air. Demander toujours à un surveillant dûment formé de se tenir à proximité. Des fumées et des gaz de soudage
peuvent se substituer à l’air, abaisser la teneur en oxygène et causer
des lésions ou des accidents mortels. S’assurer que l’air est respirable.
D Ne pas souder à proximité d’opérations de dégraissage, de nettoyage
ou de pulvérisation. La chaleur et les rayons de l’arc peuvent réagir en
présence de vapeurs et former des gaz hautement toxiques et irritants.
D Ne pas souder de métaux munis d’un revêtement, tels que la tôle
d’acier galvanisée, plombée ou cadmiée, à moins que le revêtement
n’ait été enlevé dans la zone de soudage, que l’endroit soit bien ventilé, et si nécessaire, porter un respirateur à adduction d’air. Les
revêtements et tous les métaux renfermant ces éléments peuvent dégager des fumées toxiques lorsqu’on les soude.
OM-1500-12 Page 5
LES RAYONS DE L’ARC peuvent causer des brûlures oculaires et cutanées.
Le rayonnement de l’arc génère des rayons visibles et
invisibles intenses (ultraviolets et infrarouges) susceptibles de causer des brûlures oculaires et cutanées.
Des étincelles sont projetées pendant le soudage.
D Porter un masque de soudage muni d’un filtre de la nuance adéquate
pour se protéger le visage et les yeux pendant le soudage ou pour regarder (voir les normes de sécurité ANSI Z49.1 et Z87.1).
D Porter des lunettes de sécurité à écrans latéraux sous le masque.
D Utiliser des écrans ou des barrières pour protéger les tiers de l’éclat
éblouissant ou aveuglant de l’arc ; leur demander de ne pas regarder
l’arc.
D Porter des vêtements de protection en matière durable et ignifuge
(cuir ou laine) et des chaussures de sécurité.
LE SOUDAGE peut causer un incendie ou une explosion.
Le soudage effectué sur des récipients fermés tels que
des réservoirs, des fûts ou des conduites peut causer
leur éclatement. Des étincelles peuvent être projetées
de l’arc de soudure. La projection d’étincelles, les
pièces chaudes et les équipements chauds peuvent causer des
incendies et des brûlures. Le contact accidentel de l’électrode avec tout
objet métallique peut causer des étincelles, une explosion, un surchauffement ou un incendie. Avant de commencer le soudage, vérifier et
s’assurer que l’endroit ne présente pas de danger.
D Se protéger et protéger les tiers de la projection d’étincelles et de métal chaud.
D Ne pas souder à un endroit où des étincelles peuvent tomber sur des
substances inflammables.
D Placer toutes les substances inflammables à une distance de 10,7 m
de l’arc de soudage. En cas d’impossibilité, les recouvrir soigneusement avec des protections agréées.
D Des étincelles et des matières en fusion peuvent facilement passer
même par des fissures et des ouvertures de petites dimensions.
D Surveiller tout déclenchement d’incendie et tenir un extincteur à proximité.
D Le soudage effectué sur un plafond, un plancher, une paroi ou une
cloison peut déclencher un incendie de l’autre côté.
D Ne pas souder des récipients fermés tels que des réservoirs, des fûts
ou des conduites, à moins qu’ils n’aient été préparés conformément à
l’AWS F4.1 (voir les normes de sécurité).
D Brancher le câble sur la pièce le plus près possible de la zone de soudage pour éviter que le courant ne circule sur une longue distance, par
des chemins inconnus, et ne cause des risques d’électrocution et d’incendie.
D Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
D En cas de non utilisation, enlever la baguette d’électrode du porte−
électrode ou couper le fil au raz du tube−contact.
D Porter des vêtements de protection exempts d’huile tels que des
gants en cuir, une chemise en tissu épais, des pantalons sans revers,
des chaussures montantes et un masque.
D Avant de souder, retirer tout produit combustible de ses poches, tel
qu’un briquet au butane ou des allumettes.
LES PARTICULES PROJETÉES peuvent blesser les yeux.
D Le soudage, le burinage, le passage de la pièce à
la brosse métallique et le meulage provoquent
l’émission d’étincelles et de particules métalliques. Pendant leur refroidissement, les soudures risquent de projeter du
laitier.
D
Porter des lunettes de sécurité à écrans latéraux agréés, même sous le
masque de soudage.
OM-1500-12 Page 6
LES ACCUMULATIONS DE GAZ peuvent causer des blessures ou même
la mort.
D
D
Couper l’alimentation en gaz protecteur en cas de
non utilisation.
Veiller toujours à bien ventiler les espaces confinés ou porter un respirateur à adduction d’air agréé.
LES PIÈCES CHAUDES peuvent causer des brûlures graves.
D Ne pas toucher les pièces chaudes à main nue.
D Prévoir une période de refroidissement avant
d’utiliser le pistolet ou la torche.
LES CHAMPS MAGNÉTIQUES peuvent
perturber le fonctionnement des stimulateurs cardiaques.
D
D
Les personnes qui portent un stimulateur cardiaque
doivent se tenir à distance.
Ils doivent consulter leur médecin avant de s’approcher d’un lieu où on exécute des opérations de soudage à l’arc, de gougeage ou de soudage par points.
LE BRUIT peut affecter l’ouïe.
Le bruit de certains processus et équipements peut
affecter l’ouïe.
D
Porter des protecteurs d’oreille agréés si le niveau
sonore est trop élevé.
Les BOUTEILLES
peuvent exploser.
endommagées
Les bouteilles de gaz protecteur contiennent du gaz
sous haute pression. Toute bouteille endommagée
peut exploser. Comme les bouteilles de gaz font
normalement partie du procédé de soudage, les
manipuler avec précaution.
D Protéger les bouteilles de gaz comprimé de la chaleur excessive, des
chocs mécaniques, du laitier, des flammes nues, des étincelles et des
arcs.
D Placer les bouteilles debout en les fixant dans un support stationnaire
ou dans un porte−bouteilles pour les empêcher de tomber ou de se
renverser.
D Tenir les bouteilles éloignées des circuits de soudage ou autres circuits électriques.
D Ne jamais poser une torche de soudage sur une bouteille de gaz.
D Ne jamais mettre une électrode de soudage en contact avec une bouteille de gaz.
D Ne jamais souder une bouteille contenant du gaz sous pression − elle
risquerait d’exploser.
D N’utiliser que les bouteilles de gaz protecteur, régulateurs, tuyaux et
raccords adéquats pour l’application envisagée ; les maintenir en bon
état, ainsi que les pièces connexes.
D Détourner la tête lorsqu’on ouvre la soupape d’une bouteille.
D Laisser le capuchon protecteur sur la soupape, sauf en cas d’utilisation ou de branchement de la bouteille
D Lire et suivre les instructions concernant les bouteilles de gaz comprimé, les équipements associés et les publications P−1 de la CGA,
mentionnées dans les normes de sécurité.
2-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien de
l’appareil.
Risque D’INCENDIE OU D’EXPLOSION
LES ORGANES MOBILES peuvent
causer des blessures.
D Ne pas placer l’appareil sur une surface inflammable, ni au−dessus ou à proximité d’elle.
D Se tenir à l’écart des organes mobiles comme les
ventilateurs.
D Maintenir fermés et bien fixés les portes,
panneaux, recouvrements et dispositifs de
protection.
D Ne pas installer l’appareil à proximité de produits inflammables.
D Ne pas surcharger l’installation électrique − s’assurer que l’alimentation est correctement dimensionnée et protégée avant de mettre
l’appareil en service.
LA CHUTE DE L’APPAREIL peut
blesser.
D N’utiliser que l’anneau de levage pour lever l’appareil. NE PAS utiliser le chariot, les bouteilles de
gaz ou tout autre accessoire.
D Utiliser un engin de capacité adéquate pour lever
l’appareil.
D Si on utilise un chariot élévateur pour déplacer l’unité, s’assurer que
les fourches sont suffisamment longues pour dépasser du côté opposé de l’appareil.
L’EMPLOI EXCESSIF peut FAIRE
SURCHAUFFER L’ÉQUIPEMENT.
D Prévoir une période de refroidissement ; respecter le cycle opératoire nominal.
D Réduire le courant ou le cycle opératoire avant de
reprendre le soudage.
D Ne pas obstruer les orifices ou filtrer l’alimentation en air du poste.
LES CHARGES ÉLECTROSTATIQUES peuvent endommager les circuits imprimés.
D Mettre un bracelet antistatique AVANT de manipuler des cartes ou des pièces.
D Utiliser des pochettes et des boîtes antistatiques
pour stocker, déplacer ou expédier des cartes de
circuits imprimés.
LES PIÈCES MOBILES peuvent causer des blessures.
D Se tenir à l’écart des pièces mobiles.
D Se tenir à l’écart des points de coincement tels
que les dévidoirs.
LES FILS DE SOUDAGE peuvent causer des blessures.
D Ne pas appuyer sur la gâchette avant d’en avoir
reçu l’instruction.
D Ne pas diriger le pistolet vers soi, vers d’autres
personnes ou vers toute pièce mécanique en engageant le fil de soudage.
LE RAYONNEMENT HAUTE FRÉQUENCE (H. F.) risque de causer des
interférences.
D Le rayonnement haute fréquence peut causer
des interférences avec les équipements de radionavigation et de communication, les services de
sécurité et les ordinateurs.
D Ne demander qu’à des personnes qualifiées familiarisées avec les
équipements électroniques de faire fonctionner l’installation.
D L’utilisateur est tenu de faire corriger rapidement par un électricien
qualifié les interférences causées par l’installation.
D Si la Federal Communications Commission signale des interférences, arrêter immédiatement l’appareil.
D Faire régulièrement contrôler et entretenir l’installation.
D Maintenir soigneusement fermés les panneaux et les portes des sources de haute fréquence, maintenir le jeu d’éclatement au réglage
adéquat et utiliser une terre et un blindage pour réduire les interférences éventuelles.
LE SOUDAGE À L’ARC peut causer
des interférences.
D L’énergie électromagnétique peut causer des
interférences avec l’équipement électronique
sensible tel que les ordinateurs et l’équipement
commandé par ordinateur tel que les robots.
D Veiller à ce que tout l’équipement de la zone de soudage soit compatible au point de vue électromagnétique.
D Pour réduire la possibilité d’interférence, maintenir les câbles de soudage aussi courts que possible, les grouper, et les poser aussi bas
que possible (par ex. : à terre).
D Veiller à souder à une distance de 100 mètres de tout équipement
électronique sensible.
D Veiller à ce que le poste de soudage soit posé et mis à la terre conformément au présent manuel.
D En cas d’interférences après exécution des directives précédentes, il
incombe à l’utilisateur de prendre des mesures supplémentaires telles que le déplacement du poste, l’utilisation de câbles blindés,
l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone de
travail.
LES CHAMPS MAGNÉTIQUES peuvent
affecter les stimulateurs cardiaques.
D Porteurs de stimulateur cardiaque, restez à distance.
D Les porteurs d’un stimulateur cardiaque doivent
d’abord consulter leur médecin avant de s’approcher des opérations de soudage à l’arc, de gougeage ou de soudage par points.
OM-1500-12 Page 7
2-4. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, norme ANSI Z49.1,
de l’American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
(téléphone : (305) 443−9353, site Web : www.aws.org).
Rexdale, Rexdale (Ontario) Canada M9W 1R3 (téléphone : (800)
463−6727 ou à Toronto : (416) 747−4044, site Web : www.csa−international.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, norme American Welding Society AWS
F4.1, de l’American Welding Society, 550 N.W. LeJeune Rd, Miami, FL
33126 (téléphone : (305) 443−9353, site Web : www.aws.org).
Practice For Occupational And Educational Eye And Face Protection,
norme ANSI Z87.1, de l’American National Standards Institute, 11 West
42nd Street, New York, NY 10036−8002 (téléphone : (212) 642−4900,
site Web : www.ansi.org).
National Electrical Code, norme NFPA 70, de la National Fire Protection
Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269−9101 (téléphone : (617) 770−3000, sites Web : www.nfpa.org et
www.sparky.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, norme NFPA 51B, de la National Fire Protection Association,
P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (téléphone : (617) 770−3000, site Web : www.nfpa.org et www.sparky.org).
Safe Handling of Compressed Gases in Cylinders, brochure CGA P−1,
de la Compressed Gas Association, 1735 Jefferson Davis Highway,
Suite 1004, Arlington, VA 22202−4102 (téléphone : (703) 412−0900,
site Web : www.cganet.com).
Code for Safety in Welding and Cutting, norme CSA W117.2, de la Canadian Standards Association, Standards Sales, 178 boulevard
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, de l’U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (il y a
10 bureaux régionaux − Téléphone pour la Région 5, Chicago : (312)
353−2220, site Web : www.osha.gov).
2-5. Information sur les champs électromagnétiques
Données sur le soudage électrique et les effets des champs magnétiques basse fréquence sur l’organisme
En parcourant les câbles de soudage, le courant crée des champs électromagnétiques. Les effets potentiels de tels champs restent
préoccupants. Cependant, après avoir examiné plus de 500 études qui
ont été faites pendant une période de recherche de 17 ans, un comité
de spécialistes du National Research Council a conclu : « L’accumulation de preuves n’a pas démontré que l’exposition aux champs
magnétiques et aux champs électriques à haute fréquence constitue un
risque pour la santé humaine ». Toutefois, les études et l’examen des
preuves se poursuivent. En attendant les conclusions finales de la recherche, il serait souhaitable de réduire l’exposition aux champs
électromagnétiques pendant le soudage ou le coupage.
OM-1500-12 Page 8
Afin de réduire les champs électromagnétiques en milieu de travail, respecter les consignes suivantes :
1. Garder les câbles ensemble en les torsadant ou en les fixant avec du
ruban adhésif.
2. Mettre tous les câbles du côté opposé à l’opérateur.
3. Ne pas s’enrouler les câbles autour du corps.
4. Garder le poste de soudage et les câbles le plus loin possible de soi.
5. Placer la pince de masse le plus près possible de la zone de soudage.
Consignes relatives aux stimulateurs cardiaques :
Les personnes qui portent un stimulateur cardiaque doivent avant tout
consulter leur médecin. Si ce dernier les déclare aptes, il leur est recommandé de respecter les consignes ci-dessus.
SECTION 3 − INTRODUCTION
3-1. Specifications
Type of Input
Power
Welding Power
Source Type
24 Volts AC
Single-Phase
10 Amperes
50/60 Hertz
Constant Voltage (CV)
DC With 14-Pin And
Contactor Control
Wire Feed Speed Range
Wire Diameter
Range
Welding Circuit
Rating
Standard: 50 To 780 ipm
(1.3 To 19.8 mpm)
.023 To 5/64 in (0.6
To 2 mm)
Optional High Speed: 92 To
1435 ipm (2.3 To 36.4 mpm)
Max Spool Weight:
60 lb (27 kg)
100 Volts,
750 Amperes, 100%
Duty Cycle
Weight
12 ft (3.7 m):
160 lb (73 kg)
16 ft (4.9 m):
210 lb (95 kg)
12 ft (3.7 m) Boom
16 ft (4.9 m) Boom
Maximum Height With 4 ft (1.2 m) Post
17 ft (5.2 m)
21 ft (6.4 m)
Vertical Lift Of Boom
Horizontal to 60° Above Horizontal
Horizontal to 60° Above Horizontal
SECTION 4 − INSTALLATION
4-1. Installing Swivel Into Pipe Post
5
4
1
2
3
Swingpak Base or CBC Cart
Pipe Post With Base
Steel Bolt
Secure as shown using as a minimum 1/2 in diameter SAE grade 5
steel bolts.
4
Swivel Assembly
Insert into pipe post. Lubricate
swivel.
5
2
3
Safety Collar
Y Do not remove until
instructed to.
1
Tools Needed:
3/4 in
ST-152 268-B
OM-1500−12 Page 9
4-2. Adjusting Control Tilt Bracket
1
2
3
Tilt Bracket
Rear Pivot Screw
Front Screw
Loosen rear pivot screw. Remove
front screw. Pivot control downward to desired viewing angle. Replace and tighten front screw. Tighten pivot screw.
1
2
3
802 862
4-3. Installing Boom And Reel Support
1
2
Swivel Plates
Yoke
Remove hardware from swivel
plates and yoke.
3
3
Boom
Set boom into swivel as shown.
7
4
Yoke Pin
Install pin through yoke. Install cotter pin and spread ends.
4
5
5
Install bolt, tighten hardware, and
back bolt off one half turn.
2
6
6
Bolt
Locking Knob
Install locking knob but do not
tighten.
7
Reel Support
Install reel support.
1
Tools Needed:
3/8, 3/4 in
ST-142 596-C
OM-1500−12 Page 10
4-4. Installing Wire Guide Extension
1
2
3
4
1
4
2
Wire Guide Fitting
Bolt
Monocoil Liner
Wire Guide Extension
Tighten bolt to secure liner in wire
guide fitting. Do not overtighten bolt
and crush liner.
3
Tools Needed:
3/8 in
ST-152 323
4-5. Equipment Connection Diagram
1
2
3
1
13
2
3
12
4
4
5
6
7
8
9
10
11
12
13
Welding Power Source
Remote 14 Connection
Positive (+) Weld Output
Cable
Negative (−) Weld Output
Cable
Workpiece
Weld Control
Boom
Gun
Trigger Connection
Swivel
Pipe Post And Base
Gas Hose
Gas Supply And Regulator
(Customer Supplied)
. Factory
voltage settings are
V-min 10 and V-max 38. If you
are using a power source with
a different voltage range, see
Section 5-10 for V-min and Vmax adjustments.
5
6
7
10
11
8
9
802 863
OM-1500−12 Page 11
4-6. Control Box Connections
1
2
3
Interconnecting Cable
Receptacle
Interconnecting Cable
14-Pin Control Cable
2
3
1
Ref. 802 864
4-7. 14-Pin Plug Information
Pin*
J
I
K
A
B
L
H
N
C
M D
G
F E
*The remaining pins are not used.
OM-1500−12 Page 12
Pin Information
A
24 volts ac with respect to socket G.
B
Contact closure to A completes 24 volts ac contactor control circuit.
G
Circuit common for 24 volts ac circuit.
C
+10 volts dc output to remote control with respect to socket D.
D
Remote control circuit common.
E
0 to +10 volts dc input command signal from remote control with respect to socket D.
H
Voltage feedback; 0 to +10 volts dc, 1 volt per 10 arc volts.
F
Current feedback; 0 to +10 volts dc, 1 volt per 100 amperes.
4-8. Removing Safety Collar And Adjusting Boom
1
Locking Knob
Tighten knob to prevent boom
movement. Loosen knob to allow
boom movement. Change knob position to limit upward movement.
4
Pull boom down slightly and remove
safety collar. Boom should balance
in any position from horizontal to 60
degrees above horizontal. If necessary, adjust boom as follows:
3
2
3
Threaded Rod
Jam Nut
Loosen jam nut and turn threaded
rod until boom balances. Tighten
jam nut. Be sure several full threads
are through yoke to prevent boom
falling.
4 Yoke
2
Rod
1
Rod
4
Retain safety collar for use in disassembling or moving boom.
3
2
Increasing Spring
Pressure For A
Heavy Gun
Decreasing Spring
Pressure For A
Light Gun
Tools Needed:
1-1/8 in
Ref. ST-152 380-A
4-9. Gun Recommendation Table
Process
Gun
GMAW − Hard or Cored Wires
Roughneck C-Series Guns: 300, 400, 500, And
600 Amp.
FCAW − Self-Shielding Wires
FC-1260 Or FC-1150
4-10. Wire Type, Size, And Feed Speed Capability Table
Motor Speed
Wire Type
Wire Size
Feed Speed Capability
Standard
All
.023 To 5/64 in (0.6 To 2 mm)
50 To 780 ipm (1.3 To 19.8 mpm)
Standard
All
3/32 To 7/64 in (2.4 To 2.8 mm)
50 To 700 ipm (1.3 To 17.8 mpm)
Standard
All
1/8 in (3.2 mm)
50 To 300 ipm (1.3 To 7.6 mpm)
Optional High
Speed
All
.023 To 5/64 in (0.6 To 2 mm)
92 To 1435 ipm (2.3 To 36.4 mpm)
OM-1500−12 Page 13
4-11. Installing And Threading Welding Wire
Tools Needed:
3/16, 5/64 in
15/16, 3/8 in
Install wire spool. Adjust tension nut so
wire is taut when wire
feed stops.
Pressure
Adjust
Pressure
Indicator
Scale
Install wire guide.
Pressure
Adjust
Install drive rolls.
Drive Rolls
Gun Cable
End Of Liner
NONCONDUCTIVE
SURFACE
No Wire Slip
NONCONDUCTIVE
SURFACE
Wire Slips
. Be sure that outlet cable has proper size . For soft wire or small diameter stainless . To adjust drive roll pressure, hold nozzle
liner for the welding wire size. When
installing
gun,
position
liner
extending from outlet wire guide as
close as possible to drive rolls without
touching.
Install gun. Lay gun cable out straight. Cut off
end of wire. Push wire through guides up to
drive rolls; continue to hold wire. Press Jog
button to feed wire out gun.
OM-1500−12 Page 14
steel wire, reduce drive roll pressure on
the rear roll to half that of the front rolls.
about 2 in (51 mm) from nonconductive
surface and press gun trigger to feed wire
against surface. Tighten knob so wire
does not slip. Do not overtighten. If contact tip is completely blocked, wire should
slip at the feeder (see pressure adjustment above).Cut wire off. Close cover.
152 648-A / 802 865 / 802 966 / Ref. 137 391-A / 802 954 / Ref. S-0627-A
4-12. Setting Internal DIP Switches
1
2
DIP Switch S1
DIP Switch S4 (Not For Customer Use)
DIP switch S1 allows the user to make a number of choices affecting unit operation.
w Defining Motor Speed (S1-7 & 8)
Switches 7 and 8 allow the user to define
whether the motor in use is standard speed
(50-780 inches per minute), or high speed
(92-1435 inches per minute).
. When DIP switch positions are changed, the
unit must be turned Off and then On again in
order for the new settings to be active. DIP
switches are only read on power up.
1
O 1
N
2
3
4
5
6
7
8
. In the DIP switch S1 illustrations,
the elevated slider on each switch
is shown in white. For example,
the switches above are all in the
Off position.
2
Ref. 802 866
Position Settings And Results For DIP Switch S1
7
8
7 Off, 8 Off = Standard
speed motor (50-780 inches per minute, or 1.2-19.8
meters per minute)
7
8
7 Off, 8 On = High speed
motor (92-1435 inches per
minute, or 2.3-36.4 meters
per minute)
OM-1500−12 Page 15
4-13. Power Source Selection Menu
1
2
Non-CE Model Shown
. When the feeder is turned on,
1
Program
Volts
Upper Display
Lower Display
the Power Source Selection
Menu allows the operator to select a default power source.
Selecting a default power
source, automatically sets the
correct Vmin and Vmax settings for adjusting the output
voltage of the power source.
Time (sec)
First Time Feeder Is Turned On
Wire Speed
2
Start
Trigger Hold
Crater
Pre/Postflow
Sequence
The feeder automatically goes into
the Power Source Selection Menu.
The feeder displays “dELT” on the
Upper Display and “452” on the
Lower Display, meaning that a Deltaweld 452 is the default power
source, and has a voltage range of
10V as Vmin and 38V as Vmax.
Amps
Dual Schedule
Adjust
Setup
Upper Display
Lower Display
Deltaweld 452
dELT
452
Vmin =10
Vmax =38
Deltaweld 302
dELT
302
Vmin =10
Vmax =32
Deltaweld 652
dELT
652
Vmin =10
Vmax =44
Dimension 302
dIM
302
Vmin =10
Vmax =32
Dimension 452
dIM
452
Vmin =10
Vmax =38
* * Power Source
Voltage Range
Dimension 652
dIM
652
Vmin =10
Vmax =65
Dimension 1000
dIM
1000
Vmin =10
Vmax =60
XMT 304
XMT
304
Vmin =10
Vmax =35
XMT 456
XMT
456
Vmin =10
Vmax =38
Invision 354MP
I354
MP
Vmin =10
Vmax =35
Invision 456MP
I456
MP
Vmin =10
Vmax =38
Invision 456P
I456
P
Vmin =10
Vmax =38
PHOENIX 456
PHX
456
Vmin =10
Vmax =38
SUMMIT ARC 1000
SUM
1000
Vmin =25
Vmax =44
At power up, the operator has three
seconds to select a default power
source from the list shown on the
display. Operator may scroll
through the list of power sources by
using the Adjust control. After selecting a power source the operator
has three seconds to change to a
different power source or begin
welding. After making a power
source selection, the operator may
press the Program Button to avoid
having to wait the three seconds.
When turning off the feeder, the default power source will be retained.
If voltage settings have already
been set with the Vmin and Vmax in
the Auxiliary Menu, selecting a default power source with the Power
Source Selection Menu overrides
the Vmin and Vmax voltage settings.
Next Time Feeder Is Turned On
The feeder will display the last selected default power source. The
operator has three seconds to select another power source, or press
the Program Button to exit the Power Source Selection Menu.
Disabling The Power Source
Selection Menu
** For any power sources not listed, pick a matching voltage range, or see Sec 4-10 to
set Vmin and Vmax.
OM-1500−12 Page 16
Once the default power source has
been selected the Power Source
Selection Menu may be disabled
using the Auxiliary Menus. See
Section 5-10.
SECTION 5 − OPERATION
5-1. Operational Terms
The following is a list of terms and their definitions as they apply to this wire feeder:
General Terms:
Cold Wire Jog
Feeding wire without contactor or gas valve being energized.
Sequence
A portion of the weld program, such as preflow, run-in, start, weld, crater, burnback, and postflow.
Weld Program
A group of sequences that make up a weld cycle.
5-2. Power Switch
1
1
Power Switch
802 809-B
5-3. Program Push Button
Non-CE Models
1
CE Models
2
1
1
3
3
3
2
Program Push Button
Press button to activate program
select feature. To change the program number, press the Program
push button and rotate the Adjust
control.
Program
2
Program Display
The number of the active program
is displayed.
Program Push Button LED
The LED lights to indicate the Program push button is active.
OM-1500−12 Page 17
5-4. Front Panel Controls
Nameplate For Non-CE Models
See
Section
5-5
See
Section
5-3
Program
Volts
Wire Speed
Amps
Start
Crater
Pre/Postflow
Dual Schedule
Trigger Hold
Adjust
Sequence
See
Section
5-9
See
Section
5-6
Time (sec)
See
Section
5-8
Setup
See
Section
5-7
Nameplate For CE Models
See
Section
5-5
See
Section
5-3
See
Section
5-6
See
Section
5-9
OM-1500−12 Page 18
See
Section
5-8
See
Section
5-7
5-5. Upper Display
. To set the correct voltage range for a particular power
source, see Section 4-13 for power source selection menu,
or Section 5-10 for V-Min And V-Max adjustments.
Non-CE Models
3
1
2
4
Volts
Time (sec)
5
CE Models
3
1
2
4
5
1
Upper Display
The upper display shows voltage or time.
The unit displays both preset and actual arc
voltage. When the unit is in a welding state,
actual arc voltage is displayed. The upper
display shows welding sequence time when
the Time LED is illuminated.
2
Upper Display Push Button
Press and hold button to adjust or display
weld time. Release button to display voltage.
3
Upper Display Push Button LED
The upper display push button LED illumi-
nates to indicate that information displayed
can be changed by the Adjust control.
4
5
Volts LED
Time LED
The LEDs below the display illuminate to indicate which value is being shown.
At any time while welding, the unit permits
the adjustment of the weld sequence voltage
and overrides the display of actual arc voltage.
• If the unit is displaying a welding sequence
that can be timed, the welding time display
mode is entered by pressing the upper dis-
play push button repeatedly until welding
time is the active parameter in the upper
display. At idle, the upper display toggles
between showing weld voltage or weld
time, with subsequent presses of the upper display push button.
• The unit defaults to displaying welding
voltage when a welding sequence display
mode is first entered.
• If the weld sequence has a time set (as in
spot time), after the weld program is completed, ERR TRG 1 will be displayed to indicate the weld program is complete. Release trigger to clear error.
OM-1500−12 Page 19
5-6. Lower Display
3
1
2
Non-CE Models
4
Wire Speed
Amps
5
3
1
2
CE Models
4
5
1
Lower Display
The lower display shows wire speed or
amperage. The unit displays and adjusts only
preset wire speed at idle. When the unit is in a
welding state, actual wire speed is displayed
for the active welding sequence.
2
Lower Display Push Button
Press button to choose between wire speed or
amperage functions.
3
Lower Display Push Button LED
The lower display push button LED illuminates
to indicate that information displayed can be
changed by the Adjust control.
4
5
Wire Speed LED
Amps LED
The LEDs below the display illuminate to indicate which value is being shown.
• If the unit is in a welding state that does not
involve feeding wire, the unit displays the
weld sequence wire speed. At any time during welding, the weld sequence wire speed
can be adjusted and overrides the preset
wire speed display. In other words, if the Ad-
just control is activated while welding, the
unit displays and permits adjustment of the
weld sequence wire feed speed regardless
of the active welding sequence.
• When the unit is displaying amperage, the
Amps LED illuminates. Amperage is only
displayed if the unit is in a welding state and
the amperage is above a minimum value of
25 Amps.
• The display will read dashes for amperage
readings below the amperage threshold,
prior to arc initiation.
5-7. Setup Push Button
3
4
Trigger Hold
Dual Schedule
3
2
4
2
1
1
Setup
Non-CE Models
1 Setup Push Button
Press button to choose between trigger hold
or dual schedule functions.
2 Setup Push Button LED
3 Trigger Hold LED
4 Dual Schedule LED
• When the Setup button is pressed, the Setup push button LED flashes and the Trigger
Hold LED flashes.
• The flashing LED indicates that the unit is in
the trigger hold display mode. In this mode
the upper display indicates HOLD and the
lower display indicates the trigger hold status On/Off. Use the Adjust control to change
OM-1500−12 Page 20
CE Models
the trigger hold status or press the lower display push button. If trigger hold is turned On,
the trigger hold LED illuminates and stays
On.
• When trigger hold is On, the user must
press and hold the trigger for a predefined
amount of time (the trigger hold delay time−
see Section 5-10), then release it for the trigger hold function to be active. To shut off the
weld when trigger hold is On, the user must
press and release the trigger.
• If a weld time is programmed, trigger hold is
disabled.
• Trigger hold and dual schedule cannot be
used concurrently.
• When the Setup button is pressed a second
time, the dual schedule LED flashes. In this
mode the upper display indicates DUAL and
the lower display indicates dual schedule
status On/Off. Use the Adjust control to
change the dual schedule status if desired.
• Pressing the Setup button again exits the
Setup mode. The dual schedule LED stops
flashing to indicate the dual schedule status
is Off.
• While in the Setup mode, the active program
can be adjusted without deactivating the
trigger hold Setup mode operation. If the
trigger is activated, Setup mode(s) is terminated.
5-8. Adjust Control
1
Adjust Control
The Adjust control is used to
change various sequence parameters, and to select various sequences. Refer to the section for
the function in question for information related to using the Adjust control.
1
1
Adjust
Non-CE Models
CE Models
5-9. Sequence Push Button
3
1
2
3
Start
Sequence Push Button
Sequence Push Button LED
Welding Sequence LEDs
3
Crater
Pre/Postflow
2
2
1
1
Start
Time
Preflow
Time
Weld
Time
Crater
Time
Postflow
Time
Sequence
Welding Sequence Diagram
Non-CE Models
. For more information on Setting
Sequence Parameters see Section 6-1.
• The Sequence push button allows the
selection of welding sequences. Five welding sequences are available. The default
sequence is the Weld sequence. The Weld
sequence is active on power up. Three
welding sequence LEDs are located above
the Sequence push button: Start, Crater,
and Preflow/Postflow. The applicable LED
illuminates to indicate which welding sequence is active.
• The LED illuminates to indicate that a welding sequence display mode other than Weld
is activate. Welding sequences other than
Weld must be set prior to initiating the arc.
When the unit enters a welding state, all sequence display modes are terminated and
CE Models
the weld display mode is activated.
If zero time is programmed for a timed sequence except for Weld, that sequence will
be skipped.
• In the weld sequence display mode the Sequence push button LED is Off. When the
Sequence push button is pressed, the Sequence push button flashes and the Start
LEDs flash. In this condition, the unit is in the
Start sequence display mode, and Start sequence parameters are shown in the displays.
• When the Sequence push button is pressed
a second time, the Crater sequence LED
flashes. The Sequence push button LED remains flashing. In this condition, the unit is
in the Crater sequence display mode, and
Crater sequence parameters are shown in
the displays.
• When the Sequence push button is pressed
a third time, the Preflow/Postflow sequence
LED flashes. The Sequence push button
LED remains flashing. In the Preflow display
mode the upper display shows the preflow
time and the lower display indicates the abbreviation PRE, to inform the operator that
preflow time is displayed. If the upper display push button is pressed, the Adjust control can be used to adjust preflow.
If the lower display push button is pressed, the
Adjust control can be used to select between
preflow PRE and postflow POST. When
POST is selected, the upper display can be
used to specify postflow time.
• When the Sequence push button is pressed
a fourth time, the unit returns to the welding
sequence display mode.
OM-1500−12 Page 21
5-10. Auxiliary Menus
Non-CE Models
4
5
1
2
7
Program
Volts
Time (sec)
Wire Speed
Amps
6
Start
Trigger Hold
Crater
Pre/Postflow
Dual Schedule
9
3
Sequence
Adjust
Setup
8
CE Models
4
5
1
7
2
6
9
3
8
OM-1500−12 Page 22
1
2
3
4
5
6
7
8
9
Program Display
Program Push Button
Sequence Push Button
Upper Display
Upper Display Push Button
Lower Display
Lower Display Push Button
Adjust Control
Setup Push Button
5-10 Auxiliary Menus (Continued)
Reset To Factory Settings
Arc Time
A reset menu is displayed if the following four
push buttons are pressed simultaneously:
Program, Sequence, upper display, and Setup. The upper display indicates “WIPE” . The
lower display indicates “OFF”. The lower push
button is active indicating that the Adjust control can be used to change the unit to “WIPE
ON”. When “WIPE ON” is set, if the original
four push buttons are simultaneously pressed
a second time, the unit will reset all settings to
factory default except the arc time and arc
cycle counts. If a reset is not desired, set the
display to “WIPE OFF” and simultaneously
press the Program, Sequence, upper display,
and Setup push buttons to exit the reset menu.
• If the Setup push button is pressed, the unit
displays arc time in hours.
Auxiliary Menu
• An auxiliary menu is provided if both the Sequence and Setup push buttons are pressed
simultaneously. The Setup push button and
sequence push button LEDS flash when the
auxiliary menu is displayed.
Pushing the Setup push button will step
through the menu. Pushing the sequence
push button will step through the menu in reverse.
. The auxiliary menu may be exited at any
time by pressing both the Sequence push
button and the Setup push buttons simultaneously.
V-Min And V-Max
• If the Setup push button is pressed, the unit
allows the setting of the manual override
power source min and max voltage preset
range. The minimum voltage is displayed in
the upper display and the lower display indicates “VMIN”. When the Setup push button
is pressed the unit displays the maximum
voltage setting of the welding power source.
The maximum voltage is displayed in the upper display and the lower display indicates
“VMAX”.
In both cases, the Adjust control is used to
specify the minimum and maximum voltage
settings of the welding power source. The settings correspond to arc voltage obtained at
minimum command and arc voltage obtained
at maximum command.
This method of setting “VMIN” and “VMAX”
may be used if the power source being used
is not listed in the Power Source Selection
Menu.
. If a default power source has already been
selected with the Power Source Selection
menu, setting “VMIN” and “VMAX” will
override the default power source settings.
. The power source selection menu must
be set to “OFF” when overriding the default “VMIN” or “VMAX” settings.
Power Source Selection Menu
• If the Setup push button is pressed, the unit
allows the Power Source Selection menu to
be disabled or enabled.
The upper display shows “PSS”. Lower display shows “On” or “Off”. The Adjust Control is
used to select either “On” or “Off”.
Arc time is indicated by the Program display
showing “HR”. Arc time is shown in the lower
display.
Cycles
• If the Setup push button is pressed, the unit
displays the number of cycles.
Arc cycles are indicated by the Program display showing “CL”. The arc cycle count is
shown in the lower display.
Run-In
• If the Setup button is pressed, the unit allows
setting the run-in modes. The run-in modes
are program specific. Each program may be
set to its own run-in mode.
Pressing the upper display indicates
“RUN1”. The lower display indicates
“AUTO”, meaning the factory set automatic
run-in speed is selected.
Pressing the lower display button allows a
manual setting the run-in wire speed. Speed
may be adjusted from 10% to 100% of weld
wire speed.
Pressing the lower display button allows disabling of the run-in feature. When the lower
display indicates “OFF” run-in is disabled.
Burnback
• If the Setup push button is pressed, the unit
allows burnback time to be set.
Burnback time and voltage can be specified
when the lower display indicates “BURN” and
the upper display indicates the burnback time
or voltage. The Adjust control is used to set the
desired burnback time or voltage. Burnback
settings, like run-in settings, are program specific. The active program is displayed in the
Program display and can be adjusted (see
Section 5-3).
Trigger Hold Setup
• If the Setup push button is pressed, the unit
allows trigger hold delay time to be set.
Trigger hold delay time is indicated by ”HOLD”
in the lower display and the hold delay time in
the upper display. The adjust control can be
used to specify a new delay time for trigger
hold. Trigger hold delay time is the minimum
amount of time the trigger must be held for trigger hold to work when the trigger is released
(the trigger hold function must be on). For example, if a trigger hold delay time of 2.0 seconds is defined, the operator must hold the
trigger for at least 2 seconds before releasing
it in order for the trigger hold function to work.
Once the trigger hold function is in effect, the
wire feeder will stay On until the trigger is
pressed and released again.
• There is an additional function built in called
”maximum trigger hold time” which is the
maximum length of time the trigger can be
held and the trigger hold function still work
when the trigger is released (the trigger hold
function must be on). The maximum trigger
hold time is set at 4.0 seconds after the trigger hold delay time. For example, if a trigger
hold delay time of 2.0 seconds is defined,
and the operator held the trigger in for more
than 6.0 seconds, the trigger hold function
would not be in effect and the wire feeder
would stop when the trigger is released.
• When the Setup push button is pressed
again, the menu repeats to the first menu
selection of run-in wire speed selection.
Trigger Program Select
• If the Setup push button is pressed, the unit
allows Trigger Program Select to be disabled or enabled.
The upper display shows “TSEL”. Lower display shows “On” or “Off”. The Adjust Control is
used to select either “On” or “Off”.
Trigger Program Select allows the operator to
select programs by clicking the trigger (pulling
and releasing the trigger in a maximum of 0.2
seconds). The feeder will switch between any
programs that have a minimum of 0.2 seconds
of preflow time set in the weld sequence. If programs 1 and 3 have a minimum of 0.2 seconds
of preflow time, clicking the trigger will toggle
between programs 1 and 3. If programs 1, 2,
and 4 have a minimum of 0.2 seconds of preflow time, clicking the trigger will switch from 1
to 2 to 4 to 1 to 2. Any combination of programs
may be used. Trigger Program Select cannot
be used while welding or with Dual Schedule.
Process Select
Process selection indicated by ”PROS” in the
upper display is set to either ”VOLT” or ”TRIM”
in the lower display. Each program can be selected be be a MIG program indicated by
”VOLT” or a pulsing program indicated by
”TRIM”.
Range Locks
Range locks are indicated by “LOCK” in the
upper display for wire speed or “LOCK” in the
lower display for voltage range. In a MIG program, the voltage range lock ranges from 0 to
10 volts. In a pulse program, the trim range
lock ranges from 0 to 100. The wire feed speed
range lock ranges from 0 to 250 ipm. Locks are
program dependent and wire speed is independent from voltage or trim.
Wire Feed Speed Setting
Wire feed speed setting indicated by “WFS” in
the upper display is set to “IPM” inches−per−
minute or ”MPM” meters−per−minute. This
setting is independent of the program selected.
OPT1
• If the Setup push button is pressed, the unit
allows OPT1 to be disabled or enabled.
The upper display shows “OPT1”. Lower display shows “On” or “Off”. The Adjust Control is
used to select either “On” or “Off”.
“OPT1” is used by the Water Flow Shutdown
Option to stop the weld sequence if water flow
to a water cooled gun is interrupted. A closed
set of contacts between pins 1 and 2 of RC26
on Interface Board (PC20) will allow feeder to
operate normally. Opening the contacts will
stop the weld sequence and display “ERR” in
the upper display and “OPT1” in the lower display.
OM-1500−12 Page 23
5-10 Auxiliary Menus (Continued)
OPT2
• If the Setup push button is pressed, the unit
allows OPT2 to be disabled or enabled.
The upper display shows “OPT2”. Lower display shows “On” or “Off”. The Adjust Control
is used to select either “On” or “Off”.
“OPT2” is a second input that may be used
with an external device, such as a gas flow
switch, to end the weld sequence. The gas
flow switch may be used to stop the weld sequence if shielding gas flow to the gun is interrupted. A closed set of contacts between pins
1 and 2 of RC24 on Interface Board (PC20)
will allow feeder to operate normally. Opening
the contacts will stop the weld sequence and
display “ERR” in the upper display and
“OPT2” in the lower display.
Display Hold
Display hold indicated by ”DISP” in the upper
display is set to “OFF” or “HOLD” in the lower
display. When ”HOLD” is selected, the unit will
hold the last weld information for 5 seconds
following weld termination. If any front panel
push button is pressed, or if the Adjust control
is activated, the display hold feature is terminated.
Software Revision Level
• If the Setup push button is pressed, the unit
displays the software version being used by
the interface PCB (PC20).
• When the Setup button is pressed again, the
menu repeats.
Code
Upon leaving the auxiliary menu, the user is
asked if a password code indicated by
“CODE” in the top display should be activated.
By default the code is off, indicated by “OFF”
in the lower display. The user may enter a numerical password between 0 and 999 by turning the Adjust control. When the user re−enters the auxiliary menu, the password code
must be selected to gain access to the auxiliary menu. A failed attempt return the user to the
weld screen and a counter is incremented. A
counter in the program display shows the
number of incorrect attempts. The user has
five attempts to enter the correct password
code before being locked out of the auxiliary
menu, indicated by “LOCK” in the lower display . The power may be cycled to continue
welding but the user will remained locked out
of the auxiliary menu. Pressing the Program,
Sequence, upper display, and Set−up push
buttons simultaneously, the counter can be reset in the weld screen. Resetting the counter
is indicated by “CODE” in the upper display
and “RSET” in the lower display. Pressing the
Program, Sequence, upper display, and Set−
up push buttons simultaneously again will allow the user to reset the unit to the factory defaults, indicated by “WIPE” in the upper display. Resetting the unit will also turn off the
password code feature.
5-11. Jog/Purge
1
2
Jog/Purge Push Button
Adjust Control
2
802 807-A
1
Pressing the Jog/Purge switch allows the operator to jog wire without energizing the weld
power or gas valve circuit.
• The unit provides the ability to jog the wire
feeder by means of the gun trigger or the
Jog/Purge switch. If the welding arc does
not initiate in 3 seconds after the gun trigger
is activated, the unit will perform a jog operation for a maximum of two minutes. If the gun
OM-1500−12 Page 24
trigger is still activated after two minutes, the
jog operation is terminated to prevent complete despooling of the wire, in the case of
a damaged gun.
• The unit displays the “ERR TRIG“ message
to inform the operator that the trigger is activated.
• Jog speed can be adjusted by the Adjust
control when the unit is jogging wire. The
unit displays jog speed when the unit is being jogged.
• Jogging can also be accomplished by
pressing the Jog/Purge button.
• Pressing the Jog/Purge button also allows
the operator to purge gas lines before welding and to preset gas pressure at the
regulator.
SECTION 6 − SETTING SEQUENCE PARAMETERS
6-1. Sequence Parameters In A Program
If time is set to zero in Weld
sequence, welding continues until
gun trigger is released.
Sequence
If time is set to zero in any timed
sequence except Weld, the
sequence is skipped.
Parameters
Volts
IPM
1. Preflow
Seconds
0-9.9
2. Run-In
X
3. Start
X
X
0.00-5.00
4. Weld
X
X
0-100.0
5. Crater
X
X
0-5.00
6. Burnback
X
0-0.25
7. Postflow
0-9.9
X = Setting available.
Weld Time
Crater
Time
Preflow
Time
Burnback
Time
Start
Time
Postflow
Time
Time
Burnback
Preflow
Trigger
Pressed
Run-In Start
Weld
Crater
Postflow Sequence
End
Trigger
Released
OM-1500−12 Page 25
SECTION 7 − SETTING DUAL SCHEDULE PARAMETERS
7-1. Optional Dual Schedule Switch Diagrams
1
1
1
DSS-9
2
2
1
DSS-8
2
2
Maint 2P (Maintained-Contact
2-Pole Switch)
Maint 1P (Maintained-Contact
1-Pole Switch)
1
2
TR
3
B
A
3
A
4
B
4
SECTION 8 − MAINTENANCE
8-1. Routine Maintenance
Y Disconnect power before maintaining.
3 Months
Clean and
tighten
weld
terminals.
Replace
unreadable
labels.
Replace
cracked
parts.
Check
14-pin cord.
Repair or
replace
cracked
weld
cable.
Check gas
hose and
fittings.
Check gun
cable.
6 Months
Blow out or vacuum
inside. During heavy
service, clean
monthly.
OM-1500−12 Page 26
Or
Clean
drive rolls.
8-2. Diagnostics
1
2
3
4
. There is a two-position
2
3
Wrapper
Motor Control Board PC1
LED3
DIP Switch S1
DIP switch S1 located
on motor control board
PC1. These switches
are factory-set in the
off position and must
remain in that position
for the unit to operate
correctly.
4
1
Front panel is shown removed for purpose of
illustration only. In actual use, front panel
would be in place.
Ref. 802 687
The following error messages are shown on the
upper and lower displays to indicate specific errors.
Explanations are in the text below:
ERR
ERR
ERR
ERR
ERR
ERR
COM1
TRG1
TCH1
MTR1
OPT1
OPT2
Indicates a
communication
error.
Indicates a trigger
error.
LED3-Related Error Indications
Error conditions are indicated by LED3 on
PC1. To view LED3, turn Off unit, remove
wrapper, and turn unit On. LED3 is most easily
observed from the left side of the unit.
The LED blinks in a 2.5 second cycle. The
number of blinks in this period indicates the
type of error.
The priority of the errors is related to the number of blinks indicating the error. The more
blinks, the more severe the error (motor error
is top priority). A higher priority error overrides
a lower one (if a motor error and a communication error existed, the light would blink four
times for the motor error).
Since blink On time and blink Off time are
equal in a four-blink cycle, the four−blink sequence appears as a constant blink.
1 blink = Communication Error
2 blinks = Trigger Error
Indicates a
tachometer error.
Indicates a motor
error.
3 blinks = Tach Error
4 blinks = Motor Error
ERR COM1
• The communication error occurs 2.5 seconds after a loss of communication between
the motor and front panel boards. The user
may continue to weld with this error. The error may be cleared by resetting the unit (see
Section 5-10).
ERR TRG1
• The trigger error occurs if the user has the
trigger held for more than two minutes without striking an arc (providing current override is not enabled), or if the user holds the
trigger past the postflow phase in a timed
weld. This error also occurs if the trigger is
held when the feeder is powered up. The error may be cleared by releasing the trigger.
ERR TCH1
• The tach error occurs 2 seconds after the
loss of tachometer feedback. The user may
No gas flow
detected.
Optional error
condition
continue to weld with this error. The motor
speed is regulated through the monitoring of
voltage and current.
ERR MTR1
• The motor error indicates that the motor
has been drawing too much current for too
long. To remedy this, reduce the wire feed
speed or the wire feeder torque load/duty
cycle.
ERR OPT1
• The optional 1 error indicates no coolant
flow in water flow switch option. The error
may be reset by reestablishing coolant flow
to the gun, and then pressing any button on
front panel.
ERR OPT2
• The optional 2 error indicates a problem
with optional device connected to RC24 on
Interface Board (PC20). The error may be
reset by correcting the problem, and then
pressing any button on front panel.
OM-1500−12 Page 27
8-3. Troubleshooting
Y Disconnect power before troubleshooting
Trouble
Wire feeds, shielding gas flows, but
electrode wire is not energized.
Remedy
Check interconnecting cord connections. If secure, check cord for continuity and repair or replace
(see Sections 4-5 and 4-6).
Wire feeder is on, display does not light Check and reset circuit breaker at welding power source.
up, motor does not run, gas valve and
welding power source contactor do not
pull in.
Electrode wire feeding stops or feeds
erratically during welding.
Check gun trigger connection. See gun Owner’s Manual.
Check gun trigger. See gun Owner’s Manual.
Readjust hub tension and drive roll pressure (see Section 4-11).
Change to correct size drive roll (see Table 10-1).
Clean or replace dirty or worn drive roll.
Incorrect size or worn wire guides.
Replace contact tip or liner. See gun Owner’s Manual.
Remove weld spatter or foreign matter from around nozzle opening.
Have Factory Authorized Service Agency check drive motor or motor control board PC1.
Motor runs slowly.
Check for correct input voltage.
Wire feeder power is on, displays light
up, but unit is inoperative.
Check welding gun trigger leads for continuity, and repair leads or replace gun.
OM-1500−12 Page 28
SECTION 9 − ELECTRICAL DIAGRAM
Figure 9-1. Circuit Diagram
200 592-F
OM-1500-12 Page 29
SECTION 10 − PARTS LIST
. Hardware is common and
11
10
9
Fig 10-5
7
6
8
27
31
Figure 10-1. Main Assembly
OM-1500−12 Page 30
28
29
30
18
32
Fig 10-4
26
25
24
33
20
19
23
22
21
Fig 10-2 1
18
14
2
15
16
17
Fig 10-3
13
12
2
7
3
5
4
not available unless listed.
802 866-C
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Model
16
12
Figure 10-1. Main Assembly
. . . 1 . . . . . . . . . . . . See Note
. . . 2 . . . . . . . . . . . . . 201 319
. . . 2 . . . . . . . . . . . . . 201 320
. . . . . . PLG37,38 . . 047 636
. . . . . . . . . . . . . . . . . . . 079 739
. . . . . . . . . . . . . . . . . . . 163 520
. . . 3 . . . . . . . . . . . . . 139 600
. . . 3 . . . . . . . . . . . . . 139 599
. . . 4 . . . . . . . . . . . . . 600 324
. . . 5 . . . . . . . . . . . . . 149 884
. . . 5 . . . . . . . . . . . . . 080 947
. . . 6 . . . . . . . . . . . . . 132 053
. . . 7 . . . . . . . . . . . . . 602 243
. . . 8 . . . . . . . . . . . . . 602 213
. . . 9 . . . . . . . . . . . . . 601 872
. . . 10 . . . . . . . . . . Figure 10-5
. . . 11 . . . . . . . . . . . . . 149 838
. . . 11 . . . . . . . . . . . . . 149 839
. . . 11 . . . . . . . . . . . . . 078 264
. . . 11 . . . . . . . . . . . . . 079 216
. . . 12 . . . . . . . . . . . . . 075 078
. . . 12 . . . . . . . . . . . . . 079 217
. . . 13 . . . . . . . . . . Figure 10-3
. . . 14 . . RC37 . . . . 047 637
. . . 15 . . PLG46 . . . . 115 090
. . . 16 . . PLG44 . . . 167 640
. . . 17 . . PLG4 . . . . 136 810
. . . 18 . . . . . . . . . . . . . 203 314
. . . . . . . . RC13 . . . . 080 328
. . . . . . . . . . . . . . . . . . . 079 531
. . . . . . . . . . . . . . . . . . . 604 571
. . . . . . . . PLG6 . . . . . 115 094
. . . 19 . . PLG5 . . . . 131 204
. . . 20 . . PLG45 . . . 131 203
. . . 21 . . . . . . . . . . . . . 605 227
. . . 22 . . . GS1 . . . . . 219 062
. . . . . . . . . . . . . . . . . . . 134 834
. . . 23 . . . . . . . . . . . . . 139 265
. . . 24 . . . . . . . . . . . . . 156 243
. . . 25 . . . . . . . . . . . . . 159 360
. . . 26 . . . . . . . . . . . . . 145 639
. . . 27 . . . . . . . . . . . . . 201 773
. . . 27 . . . . . . . . . . . . . 201 774
. . . 28 . . . . . . . . . . . . . 157 295
. . . 29 . . . . . . . . . . . . . 604 612
. . . 30 . . . . . . . . . . . . . 082 050
. . . 31 . . . . . . . . . . . . . 159 646
. . . 32 . . . . . . . . . . . . . 159 647
. . . 33 . . . . . . . . . . . . . . 211 989
. . Control Box, (Fig 10-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Cable, Interconnecting (consisting of) . . . . . . . . . . . . . . . . . . . . . . . 1
. . Cable, Interconnecting (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Connector & Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Connector, Circ Clamp Str Rlf Sz 17.20 . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Cable, Port No. 18-14 11/C (order by ft) . . . . . . . . . . . . . . . . . . . 17Ft . . 21Ft
. . Hose, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Hose, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Cable, Weld Cop Strd No. 4/0 (order by ft) . . . . . . . . . . . . . . . . . . 26Ft . . 30Ft
. . Bracket, Spring Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bracket, Spring Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Screw, Cap Stl Hexhd .375-16 X 1.500 Lg . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . Washer, Flat Stl Std .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 . . . . 8
. . Washer, Lock Stl Split .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . Nut, Stl Hex Full .375-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . Support, Hub & Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Pipe Post, 4ft W/Base or (optional) . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Pipe Post, 6ft W/Base (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Pipe Post, 4ft W/Base or (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Pipe Post, 6ft W/Base (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Pipe Post, 4ft W/O Base or (optional) . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Pipe Post, 6ft W/O Base (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Boom Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Pins & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Cable, Trigger (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Connector W/Sockets, Free Hanging . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . Connector, Circ Clamp Str Rlf Size 11 Amp 206358-2 . . . . . . . . 2 . . . . 2
. . . . Cable, 18/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Ft . . 2Ft
. . . . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Nut, Nyl Hex Jam .750npst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Valve, Gas W/Fittings 34VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Hose, Sae .187 Id X .410 Od (order by ft) . . . . . . . . . . . . . . . . . . . 2Ft . . 2Ft
. . Cover, Motor & Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Clamp, Motor Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Insulator, Screw Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . Strip, Buna N Compressed Sheet .062 X 4.000sq . . . . . . . . . . . . . 1 . . . . 1
. . Drive Assy., Wire (w/tach) Figure 10-4 (optional) . . . . . . . . . . . . . . 1 . . . . 1
. . Drive Assy., Wire (high speed w/tach) Figure 10-4 (optional) . . . 1 . . . . 1
. . Guide, Monocoil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Screw, Set Stl Sch 8-32 X .125 Cup Point . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . Liner, Monocoil Inlet Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Clamp, Motor Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Insulator, Motor Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Fitting, W/Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
Note: When ordering Control Box contact factory service department for proper number.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500−12 Page 31
. Hardware is common and
1
not available unless listed.
4
3
2
5
8
7
6
9
23
22
18
19
13
12
11
10
20
21
12
15
13
17
16
802 870−A
Figure 10-2. Control Box
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-2. Control Box (Figure 10-1 Item 1)
... 1 ...............
... 2 ...............
. . . 3 . . . . PC21 . . . . .
. . . 4 . . . . PC20 . . . . .
... 5 ...............
... 6 ...............
... 7 ...............
... 8 ...............
... 9 ...............
.....................
. . . 10 . . . PLG12 . . . .
. . . . . . . . . . PLG3 . . . . .
. . . 11 . . . . . . . . . . . . . . .
. . . 12 . . . . . . . . . . . . . . .
. . . 13 . . . . . . . . . . . . . . .
OM-1500−12 Page 32
200 562
200 153
200 693
210 559
047 637
200 551
134 201
024 376
148 253
204 911
141 162
115 093
079 739
163 519
139 041
. . Wrapper, Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Overlay, Upper Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Circuit Card Assy, Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Panel, Pc Card Display/Micro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Housing Rcpt+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Enclosure, Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Stand-Off Support, Pc Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . Plug, 0.625 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . Bushing, Snap−in Nyl 1.375 Id X 1.750 Mtg Hole . . . . . . . . . . . . . . . . . . 2
. . Cable, Power (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Housing Plug+Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Conn, Circ Cpc Clamp Str Rlf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Cable, Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5 Ft
. . . . Strain Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-2. Control Box (Figure 10-1 Item 1) (Continued)
. . . 15 . . . . . . . . . . . . . . .
. . . 16 . . . . . . . . . . . . . . .
. . . 17 . . . . PC1 . . . . .
. . . 17 . . . . PC1 . . . . .
. . . 18 . . . . . S1 . . . . . .
. . . 19 . . . . . . . . . . . . . . .
. . . 20 . . . . . S2 . . . . . .
. . . 21 . . . . . . . . . . . . . . .
. . . 22 . . . . . . . . . . . . . . .
. . . 23 . . . . . . . . . . . . . . .
. . . . . . . . . PLG35 . . . .
. . . . . . . . . PLG44 . . . .
. . . . . . . . PLG37,38 . . .
. . . . . . . . RC37,40 . . .
. . . . . . . . PLG6,36 . . .
. . . . . . . . . PLG46 . . . .
. . . . . . . . PLG11,61 . . .
. . . . . . . . . PLG45 . . . .
. . . . . . . . . . PLG1 . . . . .
. . . . . . . . PLG4,34 . . .
. . . . . . . . PLG7,27 . . .
. . . . . . . . . PLG10 . . . .
070 371
200 553
217 872
217 922
111 997
200 559
200 295
202 587
000 527
179 851
131 204
148 389
047 636
047 637
115 094
115 090
131 005
131 203
202 592
136 810
115 091
130 203
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
Bushing, Snap−in Nyl .937 Id X 1.125 Mtg Hole . . . . . . . . . . . . . . . . . . . .
Bracket, Control Box Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Card Assy, Motor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Card Assy, Motor Control (low speed motor) . . . . . . . . . . . . . . . . .
Switch, Rocker Spst 10a 250 Vac On-Off . . . . . . . . . . . . . . . . . . . . . . . . . .
Panel, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch, Rocker Spdt 15a 12v (On)-Off-(On) . . . . . . . . . . . . . . . . . . . . . . .
Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plug, 0.875 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Knob, Pointer 1.670 Dia X .250 Id Push On W/Spring . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500−12 Page 33
16
8
15
14
13
9
12
11
9
10
8
7
6
5
2
26
27
23
22
26
25
18
24
21
20
17
19
3
4
. Hardware is common and
28
1
not available unless listed.
ST-142 601-F
Figure 10-3. Boom Assembly
OM-1500−12 Page 34
Item
No.
Part
No.
Description
Quantity
Model
12
16
Figure 10-3. Boom Assembly (Figure 10-1 Item 13)
. . . 1 . . . . . 000 527
. . . 2 . . . . . 159 991
. . . 2 . . . . . 159 989
. . . 3 . . . . . 079 665
. . . 3 . . . . . 080 811
. . . 4 . . . . . 079 664
. . . 5 . . . . . 139 633
. . . 6 . . . . . 073 742
. . . 7 . . . . . 073 741
. . . 8 . . . . . 079 029
. . . 9 . . . . . 075 462
. . . 10 . . . . . 602 250
. . . 11 . . . . . 079 020
. . . 12 . . . . . 149 858
. . . 12 . . . . . 080 723
. . . 13 . . . . . 150 258
. . . 14 . . . . . 024 605
. . . 15 . . . . . 075 101
. . . 16 . . . . . 079 030
. . . 17 . . . . +174 754
. . . . . . . . . . . 080 157
. . . 18 . . . . . 174 688
. . . . . . . . . . . 142 804
. . . . . . . . . . . 134 327
. . . 19 . . . . . 073 666
. . . 20 . . . . . 047 224
. . . 21 . . . . . 602 246
. . . 22 . . . . . 079 667
. . . 22 . . . . . 080 812
. . . 23 . . . . . 079 632
. . . 24 . . . . . 602 243
. . . 25 . . . . . 079 622
. . . 26 . . . . . 010 313
. . . 27 . . . . . 079 621
. . . 28 . . . . . 139 336
. . . . . . . . . . . 149 322
. . Plug, 0.875 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Boom, Single . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Boom, Single . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Guide, Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Guide, Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Guide, Wire Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Liner, Monocoil 3/32-1/8 Wire X 15.687 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Pin, Clevis .750 Od X 2.156 Lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Clevis, .812 Yoke 6.062 Lg .750-16thd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Nut, Stl Hex Full Fnsh .750-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
. . Shaft, Boom Counterbalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Washer, Flat Stl Sae .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
. . Nut, Stl Hex Elastic Stop .750-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Spring, Cprsn 3.750 Od X .625 Wire X 36.000 . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Spring, Cprsn 3.750 Od X .687 Wire X 33.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Retainer, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Bearing, Ball Thr Sgl Row .750 X 1.625 X .625 . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Nut, Stl Hex Special .750-16 X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Washer, Lock Stl Ext Tooth .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Base, Swivel Boom (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . . . Fitting, Grease 1/8npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . . . Bracket, Mtg Control Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Label, Swingarc Caution Heavy Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Label, Warning General Precautionary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Bolt, Mach Stl Hexhd .750-16 X 2.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Knob, T-bar .500-13 Thd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Washer, Flat Stl Std .500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Pipe, Plstc .500 X 133.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Pipe, Plstc .500 X 181.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Bolt, U Stl .250-20 X .875 Wide X 1.375 Deep . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . .
. . Washer, Flat Stl Std .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 . . . .
. . Washer, Shldr .381 Id X .750 Od . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
. . Pin, Cotter Hair .072 X 1.437 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
. . Pulley, V Sgl Grv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Guard, Motor Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . .
. . Clamp, Hose .405 − .485clp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . .
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
5
3
2
2
1
1
2
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500−12 Page 35
. Hardware is common and
16
not available unless listed.
22
14
17
18
See Table 10-1 For
Drive Roll & Wire Guide Kits
19
20
21
22
15
5
6
7
8
23
14
9
12
10
4
11
3
13
2
1
24
25
37
38
39
40
35
36
34
26
27
33
28
32
31
29
30
802 977-B
Figure 10-4. Drive Assembly, Wire
OM-1500−12 Page 36
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-4. Drive Assembly, Wire (Figure 10-1 Item 27)
. . . 1 . . . . . . . . . . . . . . . . 010 668 . . Screw, Cap Stl Sch .250-20 X 1.500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 2 . . . . . . . . . . . . . . . . 172 075 . . Carrier, Drive Roll W/Components 24 Pitch . . . . . . . . . . . . . . . . . . . . . . 4
. . . 3 . . . . . . . . . . . . . . . . 149 962 . . Spacer, Carrier Drive Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 4 . . . . . . . . . . . . . . . . 149 486 . . Pin, Rotation Arm Rocker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 5 . . . . . . . . . . . . . . . . 163 282 . . Nut, .250-28 Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 6 . . . . . . . . . . . . . . . . 165 798 . . Spring, Pressure Arm Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 7 . . . . . . . . . . . . . . . . 165 799 . . Washer, Flat .257 Id Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 8 . . . . . . . . . . . . . . . . 132 750 . . Arm, Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 9 . . . . . . . . . . . . . . . . 150 520 . . Spacer, Rotation Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 10 . . . . . . . . . . . . . . . . 133 493 . . Ring, Retaining Ext .250 Shaft X .025thk . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 11 . . . . . . . . . . . . . . . . 133 350 . . Pin, Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 12 . . . . . . M1 . . . . . 201 230 . . Motor, Gear 1/8hp 24vdc Standard Speed . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 12 . . . . . . M1 . . . . . 201 231 . . Motor, Gear 1/8hp 24vdc High Speed (optional) . . . . . . . . . . . . . . . . . . 1
. . . 12 . . . . . . M1 . . . . . 209 131 . . Motor, Gear 1/8hp 24vdc Low Speed (optional) . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 153 491 . . . . Kit, Brush Replacement (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 153 492 . . . . . . Cap, Brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . *153 493 . . . . . . Brush, Carbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 13 . . . . . . . . . . . . . . . . 155 098 . . . . Kit, Cover Motor Gearbox (consisting of) . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 153 550 . . . . . . Cover, Motor Gearbox (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 155 099 . . . . . . . Gasket, Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 155 100 . . . . . . . Screw, Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . 154 031 . . . . . . Spacer, Locating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . 133 493 . . . . Ring, Rtng Ext .250 Shaft Grv X .025thk . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 184 136 . . Kit, Brush Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 203 631 . . Pressure Arm, S/L & Vert S/R 4 Roll (consisting of) . . . . . . . . . . . . . . . 1
. . . 14 . . . . . . . . . . . . . . . . 203 641 . . . . Washer, Flat Indicator Spring Tension . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 15 . . . . . . . . . . . . . . . . 182 415 . . . . Pin, Cotter Hair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 16 . . . . . . . . . . . . . . . . 203 640 . . . . Knob, W/Extension Short Pressure Arm . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 17 . . . . . . . . . . . . . . . . 182 156 . . . . Spring, Cprsn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 18 . . . . . . . . . . . . . . . . 182 155 . . . . Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 19 . . . . . . . . . . . . . . . . 132 746 . . . . Bushing, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 20 . . . . . . . . . . . . . . . . 203 633 . . . . Shaft, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 21 . . . . . . . . . . . . . . . . 132 747 . . . . Carrier, Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 22 . . . . . . . . . . . . . . . . 133 739 . . . . Washer, Flat Buna .375 Id X .625 Od X .062thk . . . . . . . . . . . . . . . . . 2
. . . 23 . . . . . . . . . . . . . . . . 203 637 . . . . Knob, W/Extension Long Pressure Arm . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 24 . . . . . PC51 . . . . 201 225 . . Circuit Card, Digital Tach (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . PLG5 . . . . 131 204 . . . . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 604 311 . . . . Grommet, Rbr .250 Id X .375mtg Hole . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 25 . . . . . . . . . . . . . . . . 132 611 . . Optical Encoder Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 26 . . . . . . . . . . . . . . . . 134 834 . . Hose, Sae .187 Id X .410 Od Xcoil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ft
. . . 27 . . . . . . . . . . . . . . . . 149 959 . . Fitting, Brs Barbed M 3/16tbg X .312-24 . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 28 . . . . . . . . . . . . . . . . 179 265 . . Adapter, Gun/Feeder Lh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 29 . . . . . . . . . . . . . . . . 108 940 . . Screw, Cap Stl Hexwhd .250-20 X .750 . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 30 . . . . . . . . . . . . . . . . 604 538 . . Washer, Flat Stl Sae .312 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 31 . . . . . . . . . . . . . . . . 151 437 . . Knob, Plstc T 1.125 Lg X .312-18 X 1.500 Bar . . . . . . . . . . . . . . . . . . . . 1
. . . 32 . . . . . . . . . . . . . . . . 128 237 . . Screw, Hexwhd-slt Stl Slffmg 10-32 X .500 . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 33 . . . . . . . . . . . . . . . +179 263 . . Cover, Drive Roll (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . 196 956 . . . . Label, Warning Electric Shock And Pinch . . . . . . . . . . . . . . . . . . . . . . 1
. . . 34 . . . . . . . . . . . . . . . . 601 872 . . Nut, Stl Hex Full .375-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 35 . . . . . . . . . . . . . . . . 602 213 . . Washer, Lock Stl Split .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 36 . . . . . . . . . . . . . . . . 602 243 . . Washer, Flat Stl .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 37 . . . . . . . . . . . . . . . . 601 966 . . Screw, Cap Stl Hexhd .375-16 X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 38 . . . . . . . . . . . . . . . . 167 387 . . Spacer, Locating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 39 . . . . . . . . . . . . . . . . 168 825 . . Drive, Pinion 40t 24p .376 Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 40 . . . . . . . . . . . . . . . . 133 308 . . Ring, Retaining Ext .375 Shaft X .025thk . . . . . . . . . . . . . . . . . . . . . . . . 1
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500−12 Page 37
. Hardware is common and
1
not available unless listed.
2
6
3
5
4
7*
9
3
2
10
11
12
13
14
*Includes Item 8
8
ST-146 339-B
Figure 10-5. Support, Hub & Reel
Item
No.
Part
No.
Description
Quantity
Figure 10-5. Support, Hub & Reel (Figure 10-1 Item 10)
. . . . . . 1 . . . . . . 142 399 . . Support, Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 2 . . . . . . 010 191 . . Washer, Fbr .656 Id X 1.500 Od X .125thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . 3 . . . . . . 058 628 . . Washer, Brake Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . 4 . . . . . . 058 428 . . Hub, Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 5 . . . . . . 108 008 . . Reel, Wire 60 Lb (optional) (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 6 . . . . . . 124 900 . . . . Support, Reel Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 7 . . . . . +168 104 . . . . Retainer, Spool Support (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 8 . . . . . . 166 594 . . . . . . Label, Caution Falling Wire Reel Can Cause Damage . . . . . . . . . . . . . . . . . 1
. . . . . . 9 . . . . . . 168 103 . . . . Nut, Spanner Spool Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . 10 . . . . . . 057 971 . . Washer, Flat Stl Keyed 1.500dia X .125thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 11 . . . . . . 010 233 . . Spring, Cprsn .970 Od X .120 Wire X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . 12 . . . . . . 605 941 . . Washer, Flat Stl .640 Id X 1.000 Od X 14ga Thk . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . 13 . . . . . . 136 684 . . Nut, Stl Slflkg Hex Reg .625-11 W/Nylon Insert . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . 14 . . . . . . 058 427 . . Ring, Retaining Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1500−12 Page 38
Fraction
Intermediate
Guide
Wire Size
Inlet
Guide
Table 10-1. Drive Roll and Wire Guide Kits
150 993
149 518
151 024
087 130
Metric
.023-.025 in. 0.6 mm
V-GROOVE
4 Roll
Kit
Drive
Roll
U-GROOVE
VK-GROOVE
4 Roll
Kit
Drive
Roll
4 Roll
Kit
Drive
Roll
151 036
072 000
151 052
132 958
UC-GROOVE
4 Roll
Kit
Drive
Roll
.030 in.
0.8 mm
150 993
149 518
151 025
053 695
.035 in.
0.9 mm
150 993
149 518
151 026
053 700
.040 in.
1.0 mm
150 993
149 518
161 189
053 696
.045 in.
1.1/1.2 mm 150 994
149 519
151 027
053 697
151 037
053 701
151 053
132 957
151 070
083 489
.052 in.
1.3/1.4 mm 150 994
149 519
151 028
053 698
151 038
053 702
151 054
132 956
151 071
083 490
151 029
053 699
151 039
053 706
151 055
132 955
151 072
053 708
151 056
132 959
1/16 in.
(.062 in.)
1.6 mm
150 995
149 520
.068-.072 in. 1.8 mm
150 995
149 520
5/64 in.
(.079 in.)
2.0 mm
150 995
149 520
151 040
053 704
151 057
132 960
151 073
053 710
3/32 in.
(.094 in.)
2.4 mm
150 996
149 521
151 041
053 703
151 058
132 961
151 074
053 709
7/64 in.
(.110 in.)
2.8 mm
150 996
149 521
151 042
053 705
151 059
132 962
151 075
053 711
1/8 in.
(.125 in.)
3.2 mm
150 997
149 522
151 043
053 707
151 060
132 963
151 076
053 712
Each Kit Contains An Inlet Guide, Intermediate Guide, And 045 233 Antiwear Guide With 604 612 Setscrew 8-32 x .125, Along
With 4 Drive Rolls.
2 Kits Required For Dual Models.
S-0549-D
OM-1500−12 Page 39
Notes
OM-1500−12 Page 40
Effective January 1, 2004
(Equipment with a serial number preface of “LE” or newer)
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
LIMITED WARRANTY − Subject to the terms and conditions
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to
its original retail purchaser that new Miller equipment sold after
the effective date of this limited warranty is free of defects in
material and workmanship at the time it is shipped by Miller.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
Within the warranty periods listed below, Miller will repair or
replace any warranted parts or components that fail due to such
defects in material or workmanship. Miller must be notified in
writing within thirty (30) days of such defect or failure, at which
time Miller will provide instructions on the warranty claim
procedures to be followed.
Miller shall honor warranty claims on warranted equipment
listed below in the event of such a failure within the warranty
time periods. All warranty time periods start on the date that the
equipment was delivered to the original retail purchaser, or one
year after the equipment is sent to a North American distributor
or eighteen months after the equipment is sent to an
International distributor.
1.
5 Years Parts — 3 Years Labor
*
*
2.
3 Years — Parts and Labor
*
*
*
*
*
*
*
3.
Original main power rectifiers
Inverters (input and output rectifiers only)
Transformer/Rectifier Power Sources
Plasma Arc Cutting Power Sources
Semi-Automatic and Automatic Wire Feeders
Inverter Power Supplies (Unless Otherwise Stated)
Intellitig
Maxstar 150
Engine Driven Welding Generators
(NOTE: Engines are warranted separately by
the engine manufacturer.)
1 Year — Parts and Labor Unless Specified
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
DS-2 Wire Feeder
Motor Driven Guns (w/exception of Spoolmate
Spoolguns)
Process Controllers
Positioners and Controllers
Automatic Motion Devices
RFCS Foot Controls
Induction Heating Power Sources
Water Coolant Systems
Flowgauge and Flowmeter Regulators (No Labor)
HF Units
Grids
Maxstar 85, 140
Spot Welders
Load Banks
Arc Stud Power Sources & Arc Stud Guns
Racks
Running Gear/Trailers
Plasma Cutting Torches (except APT & SAF
Models)
Field Options
(NOTE: Field options are covered under True
Blue for the remaining warranty period of the
product they are installed in, or for a minimum of
one year — whichever is greater.)
4.
6 Months — Batteries
5.
90 Days — Parts
*
MIG Guns/TIG Torches
*
*
Induction Heating Coils and Blankets
APT & SAF Model Plasma Cutting Torches
*
*
*
Remote Controls
Accessory Kits
Replacement Parts (No labor)
*
*
Spoolmate Spoolguns
Canvas Covers
Miller’s True Blue Limited Warranty shall not apply to:
1.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, slip rings,
relays or parts that fail due to normal wear. (Exception:
brushes, slip rings, and relays are covered on Bobcat,
Trailblazer, and Legend models.)
2.
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
3.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable
and necessary maintenance, or equipment which has
been used for operation outside of the specifications for the
equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND
PERSONS TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the goods at
customer’s risk and expense. Miller’s option of repair or
replacement will be F.O.B., Factory at Appleton, Wisconsin, or
F.O.B. at a Miller authorized service facility as determined by
Miller. Therefore no compensation or reimbursement for
transportation costs of any kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR
ANY OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION
OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING,
INCLUDING
ANY
IMPLIED
WARRANTY
OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT
FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED
BY MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary
from state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations
and exclusions set out above may not apply. This Limited
Warranty provides specific legal rights, and other rights may be
available, but may vary from province to province.
miller_warr 3/04
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Call 1-800-4-A-Miller or see our website at www.MillerWelds.com
to locate a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Replacement Parts
Training (Schools, Videos, Books)
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
European Headquarters −
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
Welding Process Handbooks
www.MillerWelds.com
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
PRINTED IN USA
 2004 Miller Electric Mfg. Co.
1/04
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising