Miller | LG400267W | Owner Manual | Miller SS-75DX SWINGARC User manual

Miller SS-75DX SWINGARC User manual
OM-230 299A
2006−09
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
(Gas-and Self-Shielding)
Submerged (SAW) Welding
Description
Wire Feeder
(Use with CV Power Sources)
SS-75DX Swingarc
™
SS-75DX12 and SS-75DX16
File: MIG (GMAW)
Visit our website at
www.MillerWelds.com
From Miller to You
Thank you and congratulations on choosing Miller. Now you can get
the job done and get it done right. We know you don’t have time to do
it any other way.
That’s why when Niels Miller first started building arc welders in 1929,
he made sure his products offered long-lasting value and superior
quality. Like you, his customers couldn’t afford anything less. Miller
products had to be more than the best they could be. They had to be the
best you could buy.
Today, the people that build and sell Miller products continue the
tradition. They’re just as committed to providing equipment and service
that meets the high standards of quality and value established in 1929.
This Owner’s Manual is designed to help you get the most out of your
Miller products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Miller you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will
help you figure out what the problem is. The
Miller is the first welding parts list will then help you to decide the
equipment manufacturer in exact part you may need to fix the problem.
the U.S.A. to be registered to
the ISO 9001:2000 Quality Warranty and service information for your
System Standard.
particular model are also provided.
Miller Electric manufactures a full line
of welders and welding related equipment.
For information on other quality Miller
products, contact your local Miller distributor to receive the latest full
line catalog or individual specification sheets. To locate your nearest
distributor or service agency call 1-800-4-A-Miller, or visit us at
www.MillerWelds.com on the web.
Mil_Thank 4/05
Working as hard as you do
− every power source from
Miller is backed by the most
hassle-free warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Symboles utilisés . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance . . . . . .
2-4. Proposition californienne 65 Avertissements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6. Information EMF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Installing Swivel Into Pipe Post . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Adjusting Control Tilt Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Installing Boom And Reel Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Installing Wire Guide Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Equipment Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. Control Box Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. 14-Pin Plug Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
3
3
4
4
5
5
5
7
7
8
8
9
9
9
9
10
10
11
11
12
12
4-8. Removing Safety Collar And Adjusting Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9. Gun Recommendation Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10. Wire Type, Size, And Feed Speed Capability Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-11. Installing Drive Rolls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-12. Installing PD Continuous Wire Guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-13. Installing Non-PD (Old Style) Wire Guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-14. Installing Welding Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-15. Installing Welding Wire And Adjusting Pressure Drive Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-16. Setting Internal DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-17. Power Source Selection Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Operational Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Program Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Upper Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6. Lower Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Setup Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-8. Adjust Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-9. Sequence Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-10. Auxiliary Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-11. Jog/Purge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − SETTING SEQUENCE PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Sequence Parameters In A Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − SETTING DUAL SCHEDULE PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Optional Dual Schedule Switch Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
14
15
16
17
18
19
20
21
21
21
21
22
23
24
24
25
25
26
28
29
29
30
30
TABLE OF CONTENTS
SECTION 8 − MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2. Brush Inspection And Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-3. Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-4. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 9 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONS AND ACCESSORIES
WARRANTY
31
31
31
32
33
34
36
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som _3/05
Y Warning: Protect yourself and others from injury — read and follow these precautions.
1-1. Symbol Usage
Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.
Y Marks a special safety message.
. Means “Note”; not safety related.
This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.
1-2. Arc Welding Hazards
Y The symbols shown below are used throughout this manual to
call attention to and identify possible hazards. When you see
the symbol, watch out, and follow the related instructions to
avoid the hazard. The safety information given below is only
a summary of the more complete safety information found in
the Safety Standards listed in Section 1-5. Read and follow all
Safety Standards.
Y Only qualified persons should install, operate, maintain, and
repair this unit.
D
D
D
D
D
D
Y During operation, keep everybody, especially children, away.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic wire welding, the
wire, wire reel, drive roll housing, and all metal parts touching the
welding wire are electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
D Do not touch live electrical parts.
D Wear dry, hole-free insulating gloves and body protection.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
D Use AC output ONLY if required for the welding process.
D If AC output is required, use remote output control if present on
unit.
D Additional safety precautions are required when any of the following electrically hazardous conditions are present: in damp
locations or while wearing wet clothing; on metal structures such
as floors, gratings, or scaffolds; when in cramped positions such
as sitting, kneeling, or lying; or when there is a high risk of unavoidable or accidental contact with the workpiece or ground. For these
conditions, use the following equipment in order presented: 1) a
semiautomatic DC constant voltage (wire) welder, 2) a DC manual
(stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most situations, use of a DC, constant voltage wire welder
is recommended. And, do not work alone!
D Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
D Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
D Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
D When making input connections, attach proper grounding conductor first − double-check connections.
D Frequently inspect input power cord for damage or bare wiring −
replace cord immediately if damaged − bare wiring can kill.
D
D
D
D
D
D
Turn off all equipment when not in use.
Do not use worn, damaged, undersized, or poorly spliced cables.
Do not drape cables over your body.
If earth grounding of the workpiece is required, ground it directly
with a separate cable.
Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
Do not touch electrode holders connected to two welding machines at the same time since double open-circuit voltage will be
present.
Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
Wear a safety harness if working above floor level.
Keep all panels and covers securely in place.
Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
Do not connect more than one electrode or work cable to any
single weld output terminal.
SIGNIFICANT DC VOLTAGE exists in inverter-type
welding power sources after removal of input
power.
D Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D Keep your head out of the fumes. Do not breathe the fumes.
D If inside, ventilate the area and/or use local forced ventilation at the
arc to remove welding fumes and gases.
D If ventilation is poor, wear an approved air-supplied respirator.
D Read and understand the Material Safety Data Sheets (MSDSs)
and the manufacturer’s instructions for metals, consumables,
coatings, cleaners, and degreasers.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
D Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and while wearing an air-supplied
respirator. The coatings and any metals containing these elements
can give off toxic fumes if welded.
OM-230 299 Page 1
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear an approved welding helmet fitted with a proper shade of filter lenses to protect your face and eyes when welding or watching
(see ANSI Z49.1 and Z87.1 listed in Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash,
glare and sparks; warn others not to watch the arc.
D Wear protective clothing made from durable, flame-resistant material (leather, heavy cotton, or wool) and foot protection.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D Do not weld where flying sparks can strike flammable material.
D Protect yourself and others from flying sparks and hot metal.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock, sparks, and fire
hazards.
D Do not use welder to thaw frozen pipes.
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
D Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B
for hot work and have a fire watcher and extinguisher nearby.
FLYING METAL can injure eyes.
D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
D Wear approved safety glasses with side
shields even under your welding helmet.
OM-230 299 Page 2
BUILDUP OF GAS can injure or kill.
D Shut off shielding gas supply when not in use.
D Always ventilate confined spaces or use
approved air-supplied respirator.
HOT PARTS can cause severe burns.
D Do not touch hot parts bare handed.
D Allow cooling period before working on gun or
torch.
D To handle hot parts, use proper tools and/or
wear heavy, insulated welding gloves and
clothing to prevent burns.
MAGNETIC FIELDS can affect pacemakers.
D Pacemaker wearers keep away.
D Wearers should consult their doctor before
going near arc welding, gouging, or spot
welding operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Wear approved ear protection if noise level is
high.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D Protect compressed gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open flames, sparks, and arcs.
D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Keep cylinders away from any welding or other electrical circuits.
D Never drape a welding torch over a gas cylinder.
D Never allow a welding electrode to touch any cylinder.
D Never weld on a pressurized cylinder − explosion will result.
D Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and
associated parts in good condition.
D Turn face away from valve outlet when opening cylinder valve.
D Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D Use the right equipment, correct procedures, and sufficient number of persons to lift and move cylinders.
D Read and follow instructions on compressed gas cylinders,
associated equipment, and Compressed Gas Association (CGA)
publication P-1 listed in Safety Standards.
1-3. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
MOVING PARTS can cause injury.
D Do not install or place unit on, over, or near
combustible surfaces.
D Do not install unit near flammables.
D Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
D Have only qualified persons remove doors,
panels, covers, or guards for maintenance as
necessary.
D Reinstall doors, panels, covers, or guards
when maintenance is finished and before reconnecting input power.
FALLING UNIT can cause injury.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are
long enough to extend beyond opposite side of
unit.
READ INSTRUCTIONS.
D Read Owner’s Manual before using or servicing unit.
D Use only genuine Miller/Hobart replacement
parts.
H.F. RADIATION can cause interference.
OVERUSE can cause OVERHEATING
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
D
D
STATIC (ESD) can damage PC boards.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
D
D
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
ARC WELDING can cause interference.
MOVING PARTS can cause injury.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
D
WELDING WIRE can cause injury.
D Do not press gun trigger until instructed to do
so.
D Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
D
D
D
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
1-4. California Proposition 65 Warnings
Y Welding or cutting equipment produces fumes or gases which
contain chemicals known to the State of California to cause
birth defects and, in some cases, cancer. (California Health &
Safety Code Section 25249.5 et seq.)
For Gasoline Engines:
Y Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive
harm.
Y Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
For Diesel Engines:
Y Diesel engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects, and
other reproductive harm.
OM-230 299 Page 3
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
from Global Engineering Documents (phone: 1-877-413-5184, website:
www.global.ihs.com).
Boulevard, Rexdale, Ontario, Canada M9W 1R3 (phone:
800−463−6727 or in Toronto 416−747−4044, website: www.csa−international.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1 from Global Engineering Documents (phone:
1-877-413-5184, website: www.global.ihs.com).
Practice For Occupational And Educational Eye And Face Protection,
ANSI Standard Z87.1, from American National Standards Institute, 11
West 42nd Street, New York, NY 10036−8002 (phone: 212−642−4900,
website: www.ansi.org).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269−9101 (phone: 617−770−3000, website: www.nfpa.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (phone:
617−770−3000,website: www.nfpa.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1735 Jefferson Davis Highway,
Suite 1004, Arlington, VA 22202−4102 (phone: 703−412−0900, website: www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there
are 10 Regional Offices−−phone for Region 5, Chicago, is
312−353−2220,website: www.osha.gov).
1-6. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
To reduce magnetic fields in the workplace, use the following
procedures:
OM-230 299 Page 4
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from operator as practical.
5. Connect work clamp to workpiece as close to the weld as possible.
About Pacemakers:
Pacemaker wearers consult your doctor before welding or going near
welding operations. If cleared by your doctor, then following the above
procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION
som _3/05
Y Avertissement : se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
2-1.
Symboles utilisés
Symbole graphique d’avertissement ! Attention ! Cette procédure comporte des risques possibles ! Les dangers éventuels sont représentés par les symboles graphiques joints.
Y Indique un message de sécurité particulier
. Signifie NOTE ; n’est pas relatif à la sécurité.
2-2.
Ce groupe de symboles signifie Avertissement ! Attention ! Risques
d’ÉLECTROCUTION, ORGANES MOBILES et PARTIES
CHAUDES. Consulter les symboles et les instructions afférentes
ci-dessous concernant les mesures à prendre pour supprimer
les dangers.
Dangers relatifs au soudage à l’arc
Y Les symboles représentés ci-dessous sont utilisés dans ce manuel
pour attirer l’attention et identifier les dangers possibles. En
présence de l’un de ces symboles, prendre garde et suivre les
instructions afférentes pour éviter tout risque. Les instructions en
matière de sécurité indiquées ci-dessous ne constituent qu’un
sommaire des instructions de sécurité plus complètes fournies
dans les normes de sécurité énumérées dans la Section 2-5. Lire et
observer toutes les normes de sécurité.
Y Seul un personnel qualifié est autorisé à installer, faire fonctionner, entretenir et réparer cet appareil.
Y Pendant le fonctionnement, maintenir à distance toutes les personnes, notamment les enfants de l’appareil.
D Vérifier fréquemment le cordon d’alimentation afin de s’assurer qu’il
D
D
D
D
D
D
UNE DÉCHARGE ÉLECTRIQUE peut
entraîner la mort.
D
Le contact d’organes électriques sous tension peut
provoquer des accidents mortels ou des brûlures
graves. Le circuit de l’électrode et de la pièce est
sous tension lorsque le courant est délivré à la
sortie. Le circuit d’alimentation et les circuits internes de la machine
sont également sous tension lorsque l’alimentation est sur Marche.
Dans le mode de soudage avec du fil, le fil, le dérouleur, le bloc de
commande du rouleau et toutes les parties métalliques en contact
avec le fil sont sous tension électrique. Un équipement installé ou mis
à la terre de manière incorrecte ou impropre constitue un danger.
D
D
D Ne pas toucher aux pièces électriques sous tension.
D Porter des gants isolants et des vêtements de protection secs et sans
D
D
D
D
D
D
D
D
D
trous.
S’isoler de la pièce à couper et du sol en utilisant des housses ou des
tapis assez grands afin d’éviter tout contact physique avec la pièce à
couper ou le sol.
Ne pas se servir de source électrique à courant électrique dans les zones humides, dans les endroits confinés ou là où on risque de tomber.
Se servir d’une source électrique à courant électrique UNIQUEMENT si
le procédé de soudage le demande.
Si l’utilisation d’une source électrique à courant électrique s’avère nécessaire, se servir de la fonction de télécommande si l’appareil en est
équipé.
D’autres consignes de sécurité sont nécessaires dans les conditions
suivantes : risques électriques dans un environnement humide ou si l’on
porte des vêtements mouillés ; sur des structures métalliques telles que
sols, grilles ou échafaudages ; en position coincée comme assise, à genoux ou couchée ; ou s’il y a un risque élevé de contact inévitable ou
accidentel avec la pièce à souder ou le sol. Dans ces conditions, utiliser
les équipements suivants, dans l’ordre indiqué : 1) un poste à souder DC
à tension constante (à fil), 2) un poste à souder DC manuel (électrode)
ou 3) un poste à souder AC à tension à vide réduite. Dans la plupart des
situations, l’utilisation d’un poste à souder DC à fil à tension constante
est recommandée. En outre, ne pas travailler seul !
Couper l’alimentation ou arrêter le moteur avant de procéder
à l’installation, à la réparation ou à l’entretien de l’appareil. Déverrouiller
l’alimentation selon la norme OSHA 29 CFR 1910.147 (voir normes de
sécurité).
Installer le poste correctement et le mettre à la terre convenablement
selon les consignes du manuel de l’opérateur et les normes nationales,
provinciales et locales.
Toujours vérifier la terre du cordon d’alimentation. Vérifier et s’assurer
que le fil de terre du cordon d’alimentation est bien raccordé à la borne
de terre du sectionneur ou que la fiche du cordon est raccordée à une
prise correctement mise à la terre.
En effectuant les raccordements d’entrée, fixer d’abord le conducteur
de mise à la terre approprié et contre-vérifier les connexions.
D
D
D
n’est pas altéré ou à nu, le remplacer immédiatement s’il l’est. Un fil à nu
peut entraîner la mort.
L’équipement doit être hors tension lorsqu’il n’est pas utilisé.
Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante
ou mal épissés.
Ne pas enrouler les câbles autour du corps.
Si la pièce soudée doit être mise à la terre, le faire directement avec un
câble distinct.
Ne pas toucher l’électrode quand on est en contact avec la pièce, la terre
ou une électrode provenant d’une autre machine.
Ne pas toucher des porte électrodes connectés à deux machines en
même temps à cause de la présence d’une tension à vide doublée.
N’utiliser qu’un matériel en bon état. Réparer ou remplacer sur-lechamp les pièces endommagées. Entretenir l’appareil conformément à
ce manuel.
Porter un harnais de sécurité si l’on doit travailler au-dessus du sol.
S’assurer que tous les panneaux et couvercles sont correctement en
place.
Fixer le câble de retour de façon à obtenir un bon contact métal-métal
avec la pièce à souder ou la table de travail, le plus près possible de la
soudure.
Isoler la pince de masse quand pas mis à la pièce pour éviter le contact
avec tout objet métallique.
Ne pas raccorder plus d’une électrode ou plus d’un câble de masse à
une même borne de sortie de soudage.
Il reste une TENSION DC NON NÉGLIGEABLE dans
les sources de soudage onduleur quand on a coupé
l’alimentation.
D Arrêter les convertisseurs, débrancher le courant électrique et
décharger les condensateurs d’alimentation selon les instructions indiquées dans la partie Entretien avant de toucher les pièces.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
Le soudage génère des fumées et des gaz. Leur
inhalation peut être dangereuse pour la santé.
D Ne pas mettre sa tête au-dessus des vapeurs. Ne pas respirer ces vapeurs.
D À l’intérieur, ventiler la zone et/ou utiliser une ventilation forcée au niveau de
l’arc pour l’évacuation des fumées et des gaz de soudage.
D Si la ventilation est médiocre, porter un respirateur anti-vapeurs approuvé.
D Lire et comprendre les spécifications de sécurité des matériaux (MSDS) et
les instructions du fabricant concernant les métaux, les consommables, les
revêtements, les nettoyants et les dégraisseurs.
D Travailler dans un espace fermé seulement s’il est bien ventilé ou en
portant un respirateur à alimentation d’air. Demander toujours à un surveillant dûment formé de se tenir à proximité. Des fumées et des gaz de
soudage peuvent déplacer l’air et abaisser le niveau d’oxygène provoquant des blessures ou des accidents mortels. S’assurer que l’air de
respiration ne présente aucun danger.
D Ne pas souder dans des endroits situés à proximité d’opérations de dégraissage, de nettoyage ou de pulvérisation. La chaleur et les rayons de
l’arc peuvent réagir en présence de vapeurs et former des gaz hautement toxiques et irritants.
D Ne pas souder des métaux munis d’un revêtement, tels que l’acier galvanisé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait
été enlevé dans la zone de soudure, que l’endroit soit bien ventilé et en
portant un respirateur à alimentation d’air. Les revêtements et tous les
métaux renfermant ces éléments peuvent dégager des fumées toxiques en cas de soudage.
OM-230 299 Page 5
LES RAYONS D’ARC peuvent entraîner des brûlures aux yeux et à la peau.
Le rayonnement de l’arc du procédé de soudage
génère des rayons visibles et invisibles intenses
(ultraviolets et infrarouges) susceptibles de provoquer des brûlures dans les yeux et sur la peau.
Des étincelles sont projetées pendant le soudage.
D Porter un casque de soudage approuvé muni de verres filtrants approprié pour protéger visage et yeux pendant le soudage (voir ANSI
Z49.1 et Z87.1 énuméré dans les normes de sécurité).
D Porter des lunettes de sécurité avec écrans latéraux même sous votre casque.
D Avoir recours à des écrans protecteurs ou à des rideaux pour
protéger les autres contre les rayonnements les éblouissements et
les étincelles ; prévenir toute personne sur les lieux de ne pas
regarder l’arc.
D Porter des vêtements confectionnés avec des matières résistantes
et ignifuges (cuir, coton lourd ou laine) et des bottes de protection.
LE SOUDAGE peut provoquer un
incendie ou une explosion.
Le soudage effectué sur des conteneurs fermés tels
que des réservoirs, tambours ou des conduites peut
provoquer leur éclatement. Des étincelles peuvent
être projetées de l’arc de soudure. La projection
d’étincelles, des pièces chaudes et des équipements chauds peuvent
provoquer des incendies et des brûlures. Le contact accidentel de
l’électrode avec des objets métalliques peut provoquer des étincelles,
une explosion, une surchauffe ou un incendie. Avant de commencer
le soudage, vérifier et s’assurer que l’endroit ne présente pas de
danger.
D Déplacer toutes les substances inflammables à une distance de
10,7 m de l’arc de soudage. En cas d’impossibilité, les recouvrir soigneusement avec des protections homologuées.
D Ne pas souder dans un endroit où des étincelles peuvent tomber sur
des substances inflammables.
D Se protéger, ainsi que toute autre personne travaillant sur les lieux,
contre les étincelles et le métal chaud.
D Des étincelles et des matériaux chauds du soudage peuvent
facilement passer dans d’autres zones en traversant de petites
fissures et des ouvertures.
D Afin d’éliminer tout risque de feu, être vigilant et garder toujours un
extincteur à la portée de main.
D Le soudage effectué sur un plafond, plancher, paroi ou séparation
peut déclencher un incendie de l’autre côté.
D Ne pas effectuer le soudage sur des conteneurs fermés tels que des
réservoirs, tambours, ou conduites, à moins qu’ils n’aient été préparés correctement conformément à AWS F4.1 (voir les normes de
sécurité).
D Brancher le câble de masse sur la pièce le plus près possible de la
zone de soudage pour éviter le transport du courant sur une longue
distance par des chemins inconnus éventuels en provoquant des
risques d’électrocution, d’étincelles et d’incendie.
D Ne pas utiliser le poste de soudage pour dégeler des conduites
gelées.
D En cas de non-utilisation, enlever la baguette d’électrode du porteélectrode ou couper le fil à la pointe de contact.
D Porter des vêtements de protection exempts d’huile tels que des
gants en cuir, une veste résistante, des pantalons sans revers, des
bottes et un casque.
D Avant de souder, retirer toute substance combustible de ses poches
telles qu’un allumeur au butane ou des allumettes.
D Suivre les consignes de OSHA 1910.252 (a) (2) (iv) et de NFPA 51B
pour travaux de soudage et prévoir un détecteur d’incendie et un extincteur à proximité.
DES
PARTICULES
VOLANTES
peuvent blesser les yeux.
D Le soudage, l’écaillement, le passage de la
pièce à la brosse en fil de fer, et le meulage
génèrent des étincelles et des particules
métalliques volantes. Pendant la période de
refroidissement des soudures, elles risquent
de projeter du laitier.
D Porter des lunettes de sécurité avec écrans latéraux ou un écran
facial.
OM-230 299 Page 6
LES ACCUMULATIONS DE GAZ
risquent de provoquer des blessures
ou même la mort.
D Fermer l’alimentation du gaz protecteur en cas
de non-utilisation.
D Veiller toujours à bien aérer les espaces confinés ou se servir d’un respirateur d’adduction
d’air homologué.
DES PIÈCES CHAUDES peuvent
provoquer des brûlures graves.
D Ne pas toucher des parties chaudes à mains
nues.
D Prévoir une période de refroidissement avant
d’utiliser le pistolet ou la torche.
D Ne pas toucher aux pièces chaudes, utiliser les outils recommandés et porter des gants de soudage et des vêtements épais
pour éviter les brûlures.
LES CHAMPS MAGNÉTIQUES peuvent
affecter les stimulateurs cardiaques.
D Porteurs de stimulateur cardiaque, rester
à distance.
D Les porteurs d’un stimulateur cardiaque doivent d’abord consulter leur médecin avant de
s’approcher des opérations de soudage à l’arc,
de gougeage ou de soudage par points.
LE BRUIT peut endommager l’ouïe.
Le bruit des processus et des équipements peut
affecter l’ouïe.
D Porter des protections approuvées pour les
oreilles si le niveau sonore est trop élevé.
LES BOUTEILLES peuvent exploser
si elles sont endommagées.
Des bouteilles de gaz protecteur contiennent du gaz
sous haute pression. Si une bouteille est endommagée, elle peut exploser. Du fait que les bouteilles de
gaz font normalement partie du procédé de soudage,
les manipuler avec précaution.
D Protéger les bouteilles de gaz comprimé d’une chaleur excessive, des chocs mécaniques, des dommages physiques, du laitier, des flammes ouvertes, des étincelles et des arcs.
D Placer les bouteilles debout en les fixant dans un support stationnaire ou dans un porte-bouteilles pour les empêcher de tomber ou de se renverser.
D Tenir les bouteilles éloignées des circuits de soudage ou autres
circuits électriques.
D Ne jamais placer une torche de soudage sur une bouteille à gaz.
D Une électrode de soudage ne doit jamais entrer en contact avec
une bouteille.
D Ne jamais souder une bouteille pressurisée − risque d’explosion.
D Utiliser seulement des bouteilles de gaz protecteur, régulateurs,
tuyaux et raccords convenables pour cette application spécifique ; les maintenir ainsi que les éléments associés en bon état.
D Détourner votre visage du détendeur-régulateur lorsque vous
ouvrez la soupape de la bouteille.
D Le couvercle du détendeur doit toujours être en place, sauf lorsque la bouteille est utilisée ou qu’elle est reliée pour usage ultérieur.
D Utiliser les équipements corrects, les bonnes procédures et suffisamment de personnes pour soulever et déplacer les bouteilles.
D Lire et suivre les instructions sur les bouteilles de gaz comprimé,
l’équipement connexe et le dépliant P-1 de la CGA (Compressed
Gas Association) mentionné dans les principales normes de sécurité.
2-3.
Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance
Risque D’INCENDIE OU D’EXPLOSION.
DES ORGANES MOBILES peuvent
provoquer des blessures.
D Ne pas placer l’appareil sur, au-dessus ou
à proximité de surfaces inflammables.
D Ne pas installer l’appareil à proximité de
produits inflammables.
D Ne pas surcharger l’installation électrique − s’assurer que
l’alimentation est correctement dimensionnée et protégée avant
de mettre l’appareil en service.
D S’abstenir de toucher des organes mobiles tels
que des ventilateurs.
D Maintenir fermés et verrouillés les portes,
panneaux, recouvrements et dispositifs de
protection.
D Seules des personnes qualifiées sont autorisées à enlever les
portes, panneaux, recouvrements ou dispositifs de protection
pour l’entretien.
D Remettre les portes, panneaux, recouvrements ou dispositifs de
protection quand l’entretien est terminé et avant de rebrancher
l’alimentation électrique.
LA CHUTE DE L’APPAREIL peut
blesser.
LIRE LES INSTRUCTIONS.
D Utiliser l’anneau de levage uniquement pour
soulever l’appareil, NON PAS les chariots, les
bouteilles de gaz ou tout autre accessoire.
D Utiliser un équipement de levage de capacité
suffisante pour lever l’appareil.
D En utilisant des fourches de levage pour déplacer l’unité, s’assurer que les fourches sont suffisamment longues pour dépasser
du côté opposé de l’appareil.
L’EMPLOI EXCESSIF peut
CHAUFFER L’ÉQUIPEMENT.
D Lire le manuel d’utilisation avant d’utiliser ou
d’intervenir sur l’appareil.
D Utiliser uniquement des pièces de rechange
Miller/Hobart.
LE
RAYONNEMENT
HAUTE
FRÉQUENCE (HF) risque de provoquer
des interférences.
SUR-
D Prévoir une période de refroidissement ;
respecter le cycle opératoire nominal.
D Réduire le courant ou le facteur de marche
avant de poursuivre le soudage.
D Ne pas obstruer les passages d’air du poste.
D
D
D
LES CHARGES ÉLECTROSTATIQUES
peuvent endommager les circuits
imprimés.
D
D
D Établir la connexion avec la barrette de terre
avant de manipuler des cartes ou des pièces.
D Utiliser des pochettes et des boîtes antistatiques pour stocker, déplacer ou expédier des
cartes PC.
LE SOUDAGE À L’ARC risque de
provoquer des interférences.
DES ORGANES MOBILES peuvent
provoquer des blessures.
D Ne pas s’approcher des organes mobiles.
D Ne pas s’approcher des points de coincement
tels que des rouleaux de commande.
D
D
LES FILS DE SOUDAGE peuvent
provoquer des blessures.
D
D Ne pas appuyer sur la gâchette avant d’en
avoir reçu l’instruction.
D Ne pas diriger le pistolet vers soi, d’autres
personnes ou toute pièce mécanique en engageant le fil de soudage.
2-4.
D Le rayonnement haute fréquence (HF) peut
provoquer des interférences avec les équipements de radio-navigation et de communication, les services de sécurité et les ordinateurs.
Demander seulement à des personnes qualifiées familiarisées
avec des équipements électroniques de faire fonctionner l’installation.
L’utilisateur est tenu de faire corriger rapidement par un électricien qualifié les interférences résultant de l’installation.
Si le FCC signale des interférences, arrêter immédiatement
l’appareil.
Effectuer régulièrement le contrôle et l’entretien de l’installation.
Maintenir soigneusement fermés les portes et les panneaux des
sources de haute fréquence, maintenir les éclateurs à une
distance correcte et utiliser une terre et un blindage pour réduire
les interférences éventuelles.
D
D L’énergie électromagnétique peut gêner le
fonctionnement d’appareils électroniques
comme des ordinateurs et des robots.
D Veiller à ce que tout l’équipement de la zone de
soudage soit compatible électromagnétiquement.
Pour réduire la possibilité d’interférence, maintenir les câbles de
soudage aussi courts que possible, les grouper, et les poser
aussi bas que possible (ex. par terre).
Veiller à souder à une distance de 100 mètres de tout équipement électronique sensible.
Veiller à ce que ce poste de soudage soit posé et mis à la terre
conformément à ce mode d’emploi.
En cas d’interférences après avoir pris les mesures précédentes, il incombe à l’utilisateur de prendre des mesures supplémentaires telles que le déplacement du poste, l’utilisation de
câbles blindés, l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone de travail.
Proposition californienne 65 Avertissements
Y Les équipements de soudage et de coupage produisent des
fumées et des gaz qui contiennent des produits chimiques dont
l’État de Californie reconnaît qu’ils provoquent des malformations
congénitales et, dans certains cas, des cancers. (Code de santé et
de sécurité de Californie, chapitre 25249.5 et suivants)
Pour les moteurs à essence :
Y Les gaz d’échappement des moteurs contiennent des produits
chimiques dont l’État de Californie reconnaît qu’ils provoquent
des cancers et des malformations congénitales ou autres problèmes de procréation.
Y Les batteries, les bornes et autres accessoires contiennent du
plomb et des composés à base de plomb, produits chimiques
dont l’État de Californie reconnaît qu’ils provoquent des cancers et des malformations congénitales ou autres problèmes de
procréation. Se laver les mains après manipulation.
Pour les moteurs diesel :
Y Les gaz d’échappement des moteurs diesel et certains de leurs
composants sont reconnus par l’État de Californie comme
provoquant des cancers et des malformations congénitales ou autres problèmes de procréation.
OM-230 299 Page 7
2-5.
Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
de Global Engineering Documents (téléphone : 1-877-413-5184, site Internet : www.global.ihs.com).
Boulevard, Rexdale, Ontario, Canada M9W 1R3 (téléphone :
800-463-6727 ou à Toronto 416-747-4044, site Internet :
www.csa-international.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard AWS
F4.1 de Global Engineering Documents (téléphone : 1-877-413-5184, site
Internet : www.global.ihs.com).
Practice For Occupational And Educational Eye And Face Protection,
ANSI Standard Z87.1, de American National Standards Institute, 11 West
42nd Street, New York, NY 10036-8002 (téléphone : 212-642-4900, site
Internet : www.ansi.org).
National Electrical Code, NFPA Standard 70, de National Fire Protection
Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269-9101 (téléphone : 617-770-3000, site Internet : www.nfpa.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, de National Fire Protection Association, P.O.
Box 9101, 1 Battery March Park, Quincy, MA 02269-9101 (téléphone :
617-770-3000, site Internet : www.nfpa.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
de Compressed Gas Association, 1735 Jefferson Davis Highway, Suite
1004, Arlington, VA 22202-4102 (téléphone : 703-412-0900, site Internet
: www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, de
Canadian Standards Association, Standards Sales, 178 Rexdale
2-6.
OSHA, Occupational Safety and Health Standards for General Industry,
Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and
Part 1926, Subpart J, de U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (il y a 10
bureaux régionaux−−le téléphone de la région 5, Chicago, est
312-353-2220, site Internet : www.osha.gov).
Information EMF
Considérations sur le soudage et les effets de basse fréquence et des
champs magnétiques et électriques.
Le courant de soudage, pendant son passage dans les câbles de soudage, causera des champs électromagnétiques. Il y a eu et il y a encore un
certain souci à propos de tels champs. Cependant, après avoir examiné
plus de 500 études qui ont été faites pendant une période de recherche
de 17 ans, un comité spécial ruban bleu du National Research Council a
conclu : « L’accumulation de preuves, suivant le jugement du comité, n’a
pas démontré que l’exposition aux champs magnétiques et champs électriques à haute fréquence représente un risque à la santé humaine ».
Toutefois, des études sont toujours en cours et les preuves continuent à
être examinées. En attendant que les conclusions finales de la recherche
soient établies, il vous serait souhaitable de réduire votre exposition aux
champs électromagnétiques pendant le soudage ou le coupage.
Pour réduire les champs magnétiques sur le poste de travail, appliquer
les procédures suivantes :
OM-230 299 Page 8
1. Maintenir les câbles ensemble en les tordant ou en les enveloppant.
2. Disposer les câbles d’un côté et à distance de l’opérateur.
3. Ne pas courber pas et ne pas entourer pas les câbles autour de
votre corps.
4. Garder le poste de soudage et les câbles le plus loin possible de
vous.
5. Connecter la pince sur la pièce aussi près que possible de la soudure.
En ce qui concerne les stimulateurs cardiaques
Les porteurs de stimulateur cardiaque doivent consulter leur médecin
avant de souder ou d’approcher des opérations de soudage. Si le médecin approuve, il est recommandé de suivre les procédures précédentes.
SECTION 3 − INTRODUCTION
3-1. Specifications
Type of Input
Power
Welding Power
Source Type
Maximum
Spool Weight
Wire Feed
Speed Range
Wire Diameter
Range
Welding Circuit
Rating
24 Volts AC
Single-Phase
10 Amperes
50/60 Hertz
Constant Voltage
(CV) DC With 14-Pin
And Contactor
Control
60 lb
(27 kg)
Standard: 50 To 1400
ipm (1.3 To 35.6 mpm)
.023 To 5/64 in
(0.6 To 2.0 mm)
100 Volts,
750 Amperes,
100% Duty Cycle
Weight
12 ft (3.7 m):
160 lb (73 kg)
16 ft (4.9 m):
210 lb (95 kg)
12 ft (3.7 m) Boom
16 ft (4.9 m) Boom
Maximum Height With 4 ft (1.2 m) Post
17 ft (5.2 m)
21 ft (6.4 m)
Vertical Lift Of Boom
Horizontal to 60° Above Horizontal
Horizontal to 60° Above Horizontal
NOTE
If feeder is used with a welding power source that does not provide voltage and
current feedback through the 14-pin control cable, run-in will be disabled. Arc
voltage and amperage will not be displayed.
SECTION 4 − INSTALLATION
4-1. Installing Swivel Into Pipe Post
5
4
1
2
3
Swingpak Base or CBC Cart
Pipe Post With Base
Steel Bolt
Secure as shown using as a minimum 1/2 in diameter SAE grade 5
steel bolts.
4
Swivel Assembly
Insert into pipe post. Lubricate
swivel.
5
2
3
Safety Collar
Y Do not remove until
instructed to.
1
Tools Needed:
3/4 in
ST-152 268-B
OM-230 299 Page 9
4-2. Adjusting Control Tilt Bracket
1
2
3
Tilt Bracket
Rear Pivot Screw
Front Screw
Loosen rear pivot screw. Remove
front screw. Pivot control downward to desired viewing angle. Replace and tighten front screw. Tighten pivot screw.
1
2
3
802 862
4-3. Installing Boom And Reel Support
1
2
Swivel Plates
Yoke
Remove hardware from swivel
plates and yoke.
3
3
7
Boom
Set boom into swivel as shown.
4
Yoke Pin
Install pin through yoke. Install cotter pin and spread ends.
5
4
5
6
2
6
Locking Knob
Install locking knob but do not
tighten.
7
1
Bolt
Install bolt, tighten hardware, and
back bolt off one half turn.
Reel Support
Install reel support.
Tools Needed:
3/8, 3/4 in
OM-230 299 Page 10
ST-142 596-C
4-4. Installing Wire Guide Extension
1
2
3
4
1
4
2
Wire Guide Fitting
Bolt
Monocoil Liner
Wire Guide Extension
Tighten bolt to secure liner in wire
guide fitting. Do not overtighten bolt
and crush liner.
3
Tools Needed:
3/8 in
ST-152 323
4-5. Equipment Connection Diagram
Y Turn Off wire feeder and
welding power source. Stop
engine on welding
generator.
1
13
2
Y Use only with CC/CV DC
Power Sources.
1
2
3
4
3
12
4
Weld cable and ground cable connections to power source (DCEN/
DCEP) are dependant on wire type.
5
6
7
8
9
10
11
12
13
5
6
7
Constant Current (CC) or
Constant Voltage (CV)
Welding Power Supply
Remote 14 Connection
Weld Cable To Feeder
Ground Cable To Workpiece
Workpiece
Weld Control
Boom
Gun
Trigger Connection
Swivel
Pipe Post And Base
Gas Hose
Gas Supply And Regulator
(Customer Supplied)
. Shielding gas pressure not to
10
11
exceed 100 PSI (689 kPa).
8
9
804 769-A
OM-230 299 Page 11
4-6. Control Box Connections
1
2
3
Interconnecting Cable
Receptacle
Interconnecting Cable
14-Pin Control Cable
2
3
1
Ref. 802 864
4-7. 14-Pin Plug Information
Pin*
I
J
K
A
B
L
H
N
C
M D
G
F E
*The remaining pins are not used.
OM-230 299 Page 12
Pin Information
A
24 volts ac with respect to socket G.
B
Contact closure to A completes 24 volts ac contactor control circuit.
G
Circuit common for 24 volts ac circuit.
C
+10 volts dc output to remote control with respect to socket D.
D
Remote control circuit common.
E
0 to +10 volts dc input command signal from remote control with respect to socket D.
H
Voltage feedback; 0 to +10 volts dc, 1 volt per 10 arc volts.
F
Current feedback; 0 to +10 volts dc, 1 volt per 100 amperes.
4-8. Removing Safety Collar And Adjusting Boom
1
Locking Knob
Tighten knob to prevent boom
movement. Loosen knob to allow
boom movement. Change knob position to limit upward movement.
4
Pull boom down slightly and remove
safety collar. Boom should balance
in any position from horizontal to 60
degrees above horizontal. If necessary, adjust boom as follows:
3
2
3
Threaded Rod
Jam Nut
Loosen jam nut and turn threaded
rod until boom balances. Tighten
jam nut. Be sure several full threads
are through yoke to prevent boom
falling.
4 Yoke
2
Rod
1
Rod
4
Retain safety collar for use in disassembling or moving boom.
3
2
Increasing Spring
Pressure For A
Heavy Gun
Tools Needed:
Decreasing Spring
Pressure For A
Light Gun
1-1/8 in
Ref. ST-152 380-A
4-9. Gun Recommendation Table
Process
Gun
GMAW − Hard or Cored Wires
Q-Series Guns: 300, 400, 500, And 600 Amp.
FCAW − Self-Shielding Wires
FC-1260 Or FC-1150
4-10. Wire Type, Size, And Feed Speed Capability Table
Motor Speed
Wire Type
Wire Size
Feed Speed Capability
Standard
All
.023 To 5/64 in (0.6 To 2 mm)
50 To 1400 ipm (1.3 To 35.6 mpm)
OM-230 299 Page 13
4-11. Installing Drive Rolls
1
2
3
4
Drive Roll Carrier
Ejector Button
Drive Roll
Pressure Door Assembly
Installation
Open pressure door assembly.
Lift drive roll swing arm.
Align drive roll slots with three lobes
on drive roll carrier.
Insert drive roll onto carrier. Drive
roll will snap into place.
When closing swing arm, push firmly into position.
Swing arm has built in resistance to
prevent swing arm from closing
abruptly.
. When using cored welding wire
use knurled drive rolls.
Removal
4
. Remove PD wire guide before
removing lower drive rolls.
Lift up drive roll swing arm and
press ejector button in middle of
drive roll carrier.
1
2
3
804 737-A
Notes
OM-230 299 Page 14
4-12. Installing PD Continuous Wire Guides
3
1
2
4
Ref. 804 731-A
. PD Continuous Wire Guides:
Should be used with .068/.072 in
(1.8 mm) and smaller diameter wire for
optimal performance.
Should be used with PD drive rolls
and cannot be used with non-PD (oldstyle) drive rolls.
. 70 series wire guides are not compat1
ible with 75 series wire feeders.
PD Wire Guide (Two Pieces
interlocked for Aluminum Wire)
2
PD Wire Guide (Hard Wire)
3
4
PD Inlet Guide
Pressure Door Assembly
Installing PD continuous wire guides
with PD drive rolls.
. Drive rolls are identified by the initials
PD and a part number on the drive roll.
Open pressure door assembly.
Lift up drive roll swing arms.
Remove PD inlet guide.
Insert wire guide gun end (indicated with arrow) into block near brass power pin gun
connector.
Install PD inlet guide.
. Do not tighten set screw to secure inlet
guide.
. Set screw may be used to secure PD
inlet guide replacements such as wire
straighteners or conduit adapters.
OM-230 299 Page 15
4-13. Installing Non-PD (Old Style) Wire Guides
6
1
2
3
Ref. 804 732-A
4
Tools Needed:
5
1/16, 1/8, 5/32 in
Installing wire guides with non- PD (oldstyle) drive rolls
Open pressure door assembly.
. Non-PD
Install PD inlet guide.
(old-style) wire guides and
drive rolls should be used with 5/64 in
(2.0 mm) and larger diameter wire.
1
2
3
4
5
6
PD Inlet Guide
Intermediate Guide
Guide Holder
Exit Guide
Set Screw
Pressure Door Assembly
OM-230 299 Page 16
Lift up drive roll swing arms.
. Do not tighten set screw to secure inlet
guide.
. Set screw may be used to secure PD
inlet guide replacements such as wire
straighteners or conduit adapters.
Remove screw securing intermediate guide
holder. (Guide holder is located between
the lower front and rear drive roll carriers.)
Rotate guide holder 180 degrees and reinstall.
Install intermediate guide into guide holder
and tighten set screw.
Loosen set screw, insert exit guide into
block near brass power pin gun connection
and secure with set screw.
. When
using smaller diameter inlet
guide (219108) with non-PD (old style)
drive rolls, a 1/4 in (6 mm) gap will be
present between the guide and drive
roll.
4-14. Installing Welding Gun
804 730-A
3
4
1
2
1
Installing gun with
Accu-Mate connection
1
Gun Locking Tab
2
Power Clamp Knob
3
Power Pin Groove
4
Gun Connection End
Installing gun with Accu-Mate connection
Loosen power clamp knob to allow power
pin of gun to clear the gun locking tab.
When installing gun, the liner should extend
2
Installing gun without
Accu-Mate connection
into the PD continuous guide (or exit guide
if used) as far as possible without interfering with the guide.
Align the groove in the power pin of the gun
with the gun locking tab.
Secure gun by tightening power clamp
knob.
Installing gun without Accu-Mate connection
When using a gun without the groove in the
power pin, loosen power clamp knob and
rotate gun locking tab 180 degrees. This
prevents the locking tab from extending into
the power pin gun connection.
When installing gun, the liner should extend
into the PD continuous guide (or exit guide
if used) as far as possible without interfering with the guide.
Secure gun by tightening power clamp
knob.
OM-230 299 Page 17
4-15. Installing Welding Wire And Adjusting Pressure Drive Setting
Thread wire.
Install wire spool. Adjust tension nut so
wire is taut when wire
feed stops.
Adjust tension.
Pressure door
assembly not
shown.
2
Drive Rolls
1
End Of Liner
Ref. 804 727-A
Back Of Gun
NONCONDUCTIVE
SURFACE
No Wire Slip
NONCONDUCTIVE
SURFACE
Wire Slips
Tools Needed:
15/16 in
1
2
Drive Roll Pressure Adjustment Lever
Notch In Lever (Indicates Pressure
Settings)
Pressure drive settings range from 1 to 8 with
8 being the maximum setting.
. When
using cored welding wire use
knurled drive rolls.
. For aluminum (soft) wire set pressure
drive setting at 4 or below.
OM-230 299 Page 18
. Be sure that gun has proper size liner for
the welding wire size.
When installing gun, the liner should extend
into the PD continuous guide (or exit guide if
used) as far as possible without interfering
with the guide.
Install gun. Lay gun cable out straight. Cut off
end of wire. Push wire through guide up to
drive rolls; continue to hold wire. Press Jog
button to feed wire out gun.
To adjust drive roll pressure, hold nozzle
about 2 in (51 mm) from nonconductive
surface and press gun trigger to feed wire
against surface. Adjust pressure drive lever
so wire does not slip. Do not overtighten. If
contact tip is completely blocked, wire should
slip at the feeder (see pressure adjustment
above.)
Cut wire off.
4-16. Setting Internal DIP Switches
Remove wrapper.
1
DIP Switch S1 And S4 on Display
Board PC20
DIP Switch S1 On Motor Board PC1
2
1
Factory Set Default Settings
For DIP Switches S1 And S4
O 1
N
2
Factory Set Default Settings For DIP Switch S1
3
4
5
6
7
8
2
Tools Needed:
1/4 in
Ref. 802 866 / 803 063
OM-230 299 Page 19
4-17. Power Source Selection Menu
1
2
Non-CE Model Shown
. When the feeder is turned on,
1
Program
Volts
Upper Display
Lower Display
the Power Source Selection
Menu allows the operator to select a default power source.
Selecting a default power
source, automatically sets the
correct Vmin and Vmax settings for adjusting the output
voltage of the power source.
Time (sec)
First Time Feeder Is Turned On
Wire Speed
Amps
Start
Trigger Hold
Crater
Pre/Postflow
Sequence
The feeder automatically goes into
the Power Source Selection Menu.
The feeder displays “dELT” on the
Upper Display and “452” on the
Lower Display, meaning that a Deltaweld 452 is the default power
source, and has a voltage range of
10V as Vmin and 38V as Vmax.
2
Dual Schedule
Adjust
Setup
Upper Display
Lower Display
Deltaweld 452
dELT
452
Vmin =10
Vmax =38
Deltaweld 302
dELT
302
Vmin =10
Vmax =32
Deltaweld 652
dELT
652
Vmin =10
Vmax =44
Dimension 302
dIM
302
Vmin =10
Vmax =32
Dimension 452
dIM
452
Vmin =10
Vmax =38
* * Power Source
Voltage Range
Dimension 652
dIM
652
Vmin =10
Vmax =65
Dimension 1000
dIM
1000
Vmin =10
Vmax =60
XMT 304
XMT
304
Vmin =10
Vmax =35
XMT 456
XMT
456
Vmin =10
Vmax =38
Invision 354MP
I354
MP
Vmin =10
Vmax =35
Invision 456MP
I456
MP
Vmin =10
Vmax =38
Invision 456P
I456
P
Vmin =10
Vmax =38
PHOENIX 456
PHX
456
Vmin =10
Vmax =38
SUMMIT ARC 1000
SUM
1000
Vmin =25
Vmax =44
** For any power sources not listed, pick a matching voltage range, or see Sec 4-10 to
set Vmin and Vmax.
OM-230 299 Page 20
At power up, the operator has three
seconds to select a default power
source from the list shown on the
display. Operator may scroll
through the list of power sources by
using the Adjust control. After selecting a power source the operator
has three seconds to change to a
different power source or begin
welding. After making a power
source selection, the operator may
press the Program Button to avoid
having to wait the three seconds.
When turning off the feeder, the default power source will be retained.
If voltage settings have already
been set with the Vmin and Vmax in
the Auxiliary Menu, selecting a default power source with the Power
Source Selection Menu overrides
the Vmin and Vmax voltage settings.
Next Time Feeder Is Turned On
The feeder will display the last selected default power source. The
operator has three seconds to select another power source, or press
the Program Button to exit the Power Source Selection Menu.
Disabling The Power Source
Selection Menu
Once the default power source has
been selected the Power Source
Selection Menu may be disabled
using the Auxiliary Menus. See
Section 5-10.
SECTION 5 − OPERATION
5-1. Operational Terms
The following is a list of terms and their definitions as they apply to this wire feeder:
General Terms:
Cold Wire Jog
Feeding wire without contactor or gas valve being energized.
Sequence
A portion of the weld program, such as preflow, run-in, start, weld, crater, burnback, and postflow.
Weld Program
A group of sequences that make up a weld cycle.
5-2. Power Switch
1
Power Switch
1
802 809-B
5-3. Program Push Button
Non-CE Models
1
CE Models
2
1
2
3
3
2
Program Push Button
Press button to activate program
select feature. To change the program number, press the Program
push button and rotate the Adjust
control.
1
Program
Program Display
The number of the active program
is displayed.
3
Program Push Button LED
The LED lights to indicate the Program push button is active.
OM-230 299 Page 21
5-4. Front Panel Controls
Nameplate For Non-CE Models
See
Section
5-5
See
Section
5-3
Program
Volts
Wire Speed
Amps
Start
Crater
Pre/Postflow
Dual Schedule
Trigger Hold
Adjust
Sequence
See
Section
5-9
See
Section
5-6
Time (sec)
See
Section
5-8
Setup
See
Section
5-7
Nameplate For CE Models
See
Section
5-5
See
Section
5-3
See
Section
5-6
See
Section
5-9
OM-230 299 Page 22
See
Section
5-8
See
Section
5-7
5-5. Upper Display
. To set the correct voltage range for a particular power
source, see Section 4-17 for power source selection menu,
or Section 5-10 for V-Min And V-Max adjustments.
Non-CE Models
3
1
2
4
Volts
Time (sec)
5
CE Models
3
1
2
4
5
1 Upper Display
The upper display shows voltage or time. The
unit displays both preset and actual arc voltage. When the unit is in a welding state, actual
arc voltage is displayed. No actual arc voltage
will be displayed if welding power source does
not provide voltage feedback through the
14-pin control cable. The upper display shows
welding sequence time when the Time LED is
illuminated.
2 Upper Display Push Button
Press and hold button to adjust or display weld
time. Release button to display voltage.
3 Upper Display Push Button LED
The upper display push button LED illumi-
nates to indicate that information displayed
can be changed by the Adjust control.
4
Volts LED
5
Time LED
The LEDs below the display illuminate to indicate which value is being shown.
At any time while welding, the unit permits the
adjustment of the weld sequence voltage and
overrides the display of actual arc voltage.
• If the unit is displaying a welding sequence
that can be timed, the welding time display
mode is entered by pressing the upper dis-
play push button repeatedly until welding
time is the active parameter in the upper display. At idle, the upper display toggles between showing weld voltage or weld time,
with subsequent presses of the upper display push button.
• The unit defaults to displaying welding voltage when a welding sequence display mode
is first entered.
• If the weld sequence has a time set (as in
spot time), after the weld program is completed, ERR TRG 1 will be displayed to indicate the weld program is complete. Release
trigger to clear error.
OM-230 299 Page 23
5-6. Lower Display
3
1
2
Non-CE Models
4
Wire Speed
Amps
5
3
1
2
CE Models
4
5
1
Lower Display
The lower display shows wire speed or
amperage. The unit displays and adjusts only
preset wire speed at idle. When the unit is in a
welding state, actual wire speed is displayed
for the active welding sequence.
2
Lower Display Push Button
Press button to choose between wire speed or
amperage functions.
3
Lower Display Push Button LED
The lower display push button LED illuminates
to indicate that information displayed can be
changed by the Adjust control.
4 Wire Speed LED
5 Amps LED
The LEDs below the display illuminate to indicate which value is being shown.
• If the unit is in a welding state that does not
involve feeding wire, the unit displays the
weld sequence wire speed. At any time during welding, the weld sequence wire speed
can be adjusted and overrides the preset
wire speed display. In other words, if the Adjust control is activated while welding, the
unit displays and permits adjustment of the
weld sequence wire feed speed regardless
of the active welding sequence.
• When the unit is displaying amperage, the
Amps LED illuminates. Amperage is only
displayed if the unit is in a welding state and
the amperage is above a minimum value of
25 Amps.
• The display will read dashes for amperage
readings below the amperage threshold,
prior to arc initiation or if welding power
source does not provide current feedback
through the 14-pin control cable.
5-7. Setup Push Button
3
4
Trigger Hold
Dual Schedule
3
2
4
2
1
1
Setup
Non-CE Models
1 Setup Push Button
Press button to choose between trigger hold
or dual schedule functions.
2 Setup Push Button LED
3 Trigger Hold LED
4 Dual Schedule LED
• When the Setup button is pressed, the Setup push button LED flashes and the Trigger
Hold LED flashes.
• The flashing LED indicates that the unit is in
the trigger hold display mode. In this mode
the upper display indicates HOLD and the
lower display indicates the trigger hold status On/Off. Use the Adjust control to change
OM-230 299 Page 24
CE Models
the trigger hold status or press the lower display push button. If trigger hold is turned On,
the trigger hold LED illuminates and stays
On.
• When trigger hold is On, the user must
press and hold the trigger for a predefined
amount of time (the trigger hold delay time−
see Section 5-10), then release it for the trigger hold function to be active. To shut off the
weld when trigger hold is On, the user must
press and release the trigger.
• If a weld time is programmed, trigger hold is
disabled.
• Trigger hold and dual schedule cannot be
used concurrently.
• When the Setup button is pressed a second
time, the dual schedule LED flashes. In this
mode the upper display indicates DUAL and
the lower display indicates dual schedule
status On/Off. Use the Adjust control to
change the dual schedule status if desired.
• Pressing the Setup button again exits the
Setup mode. The dual schedule LED stops
flashing to indicate the dual schedule status
is Off.
• While in the Setup mode, the active program
can be adjusted without deactivating the
trigger hold Setup mode operation. If the
trigger is activated, Setup mode(s) is terminated.
5-8. Adjust Control
1
Adjust Control
The Adjust control is used to
change various sequence parameters, and to select various sequences. Refer to the section for
the function in question for information related to using the Adjust control.
1
1
Adjust
Non-CE Models
CE Models
5-9. Sequence Push Button
3
Start
1
2
3
3
Crater
Pre/Postflow
2
2
1
1
Start
Time
Preflow
Time
Sequence Push Button
Sequence Push Button LED
Welding Sequence LEDs
Weld
Time
Crater
Time
Postflow
Time
Sequence
Welding Sequence Diagram
Non-CE Models
. For more information on Setting
Sequence Parameters see Section 6-1.
• The Sequence push button allows the
selection of welding sequences. Five welding sequences are available. The default
sequence is the Weld sequence. The Weld
sequence is active on power up. Three
welding sequence LEDs are located above
the Sequence push button: Start, Crater,
and Preflow/Postflow. The applicable LED
illuminates to indicate which welding sequence is active.
• The LED illuminates to indicate that a welding sequence display mode other than Weld
is activate. Welding sequences other than
Weld must be set prior to initiating the arc.
When the unit enters a welding state, all sequence display modes are terminated and
CE Models
the weld display mode is activated.
If zero time is programmed for a timed sequence except for Weld, that sequence will
be skipped.
• In the weld sequence display mode the Sequence push button LED is Off. When the
Sequence push button is pressed, the Sequence push button flashes and the Start
LEDs flash. In this condition, the unit is in the
Start sequence display mode, and Start sequence parameters are shown in the displays.
• When the Sequence push button is pressed
a second time, the Crater sequence LED
flashes. The Sequence push button LED remains flashing. In this condition, the unit is
in the Crater sequence display mode, and
Crater sequence parameters are shown in
the displays.
• When the Sequence push button is pressed
a third time, the Preflow/Postflow sequence
LED flashes. The Sequence push button
LED remains flashing. In the Preflow display
mode the upper display shows the preflow
time and the lower display indicates the abbreviation PRE, to inform the operator that
preflow time is displayed. If the upper display push button is pressed, the Adjust control can be used to adjust preflow.
If the lower display push button is pressed, the
Adjust control can be used to select between
preflow PRE and postflow POST. When
POST is selected, the upper display can be
used to specify postflow time.
• When the Sequence push button is pressed
a fourth time, the unit returns to the welding
sequence display mode.
OM-230 299 Page 25
5-10. Auxiliary Menus
Non-CE Models
4
5
1
2
7
Program
Volts
Time (sec)
Wire Speed
Amps
6
Start
Trigger Hold
Crater
Pre/Postflow
Dual Schedule
3
Sequence
Adjust
9
Setup
8
CE Models
4
5
1
7
2
6
9
3
8
OM-230 299 Page 26
1
2
3
4
5
6
7
8
9
Program Display
Program Push Button
Sequence Push Button
Upper Display
Upper Display Push Button
Lower Display
Lower Display Push Button
Adjust Control
Setup Push Button
5-10 Auxiliary Menus (Continued)
Reset To Factory Settings
A reset menu is displayed if the following four
push buttons are pressed simultaneously:
Program, Sequence, upper display, and Setup. The upper display indicates “WIPE” . The
lower display indicates “OFF”. The lower
push button is active indicating that the Adjust
control can be used to change the unit to
“WIPE ON”. When “WIPE ON” is set, if the original four push buttons are simultaneously
pressed a second time, the unit will reset all
settings to factory default except the arc time
and arc cycle counts. If a reset is not desired,
set the display to “WIPE OFF” and simultaneously press the Program, Sequence, upper
display, and Setup push buttons to exit the reset menu.
Auxiliary Menu
• An auxiliary menu is provided if both the Sequence and Setup push buttons are
pressed simultaneously. The Setup push
button and sequence push button LEDS
flash when the auxiliary menu is displayed.
Pushing the Setup push button will step
through the menu. Pushing the sequence
push button will step through the menu in reverse.
. The auxiliary menu may be exited at any
time by pressing both the Sequence push
button and the Setup push buttons simultaneously.
V-Min And V-Max
• If the Setup push button is pressed, the unit
allows the setting of the manual override
power source min and max voltage preset
range. The minimum voltage is displayed in
the upper display and the lower display indicates “VMIN”. When the Setup push button
is pressed the unit displays the maximum
voltage setting of the welding power
source. The maximum voltage is displayed
in the upper display and the lower display
indicates “VMAX”.
In both cases, the Adjust control is used to
specify the minimum and maximum voltage
settings of the welding power source. The settings correspond to arc voltage obtained at
minimum command and arc voltage obtained
at maximum command.
This method of setting “VMIN” and “VMAX”
may be used if the power source being used
is not listed in the Power Source Selection
Menu.
. If a default power source has already
been selected with the Power Source
Selection menu, setting “VMIN” and
“VMAX” will override the default power
source settings.
. The power source selection menu must
be set to “OFF” when overriding the default “VMIN” or “VMAX” settings.
Power Source Selection Menu
• If the Setup push button is pressed, the unit
allows the Power Source Selection menu to
be disabled or enabled.
The upper display shows “PSS”. Lower display shows “On” or “Off”. The Adjust Control
is used to select either “On” or “Off”.
Arc Time
• If the Setup push button is pressed, the unit
displays arc time in hours.
Arc time is indicated by the Program display
showing “HR”. Arc time is shown in the lower
display.
Cycles
• If the Setup push button is pressed, the unit
displays the number of cycles.
Arc cycles are indicated by the Program display showing “CL”. The arc cycle count is
shown in the lower display.
Run-In
• If the Setup button is pressed, the unit allows setting the run-in modes. The run-in
modes are program specific. Each program
may be set to its own run-in mode.
The upper display indicates “RUNI”. The
lower display indicates “AUTO”, meaning
the factory set automatic run-in speed is selected.
Pressing the lower display button allows a
manual setting the run-in wire speed. Speed
may be adjusted from 10% to 100% of weld
wire speed.
Pressing the lower display button allows
disabling of the run-in feature. When the
lower display indicates “OFF” run-in is disabled.
Burnback
• If the Setup push button is pressed, the unit
allows burnback time to be set.
Burnback time and voltage can be specified
when the lower display indicates “BURN” and
the upper display indicates the burnback time
or voltage. The Adjust control is used to set
the desired burnback time or voltage. Burnback settings, like run-in settings, are program specific. The active program is displayed in the Program display and can be adjusted (see Section 5-3).
Trigger Hold Setup
• If the Setup push button is pressed, the unit
allows trigger hold delay time to be set.
Trigger hold delay time is indicated by
”HOLD” in the lower display and the hold
delay time in the upper display. The adjust
control can be used to specify a new delay
time for trigger hold. Trigger hold delay time is
the minimum amount of time the trigger must
be held for trigger hold to work when the trigger is released (the trigger hold function must
be on). For example, if a trigger hold delay
time of 2.0 seconds is defined, the operator
must hold the trigger for at least 2 seconds before releasing it in order for the trigger hold
function to work. Once the trigger hold function is in effect, the wire feeder will stay On until the trigger is pressed and released again.
• There is an additional function built in called
”maximum trigger hold time” which is the
maximum length of time the trigger can be
held and the trigger hold function still work
when the trigger is released (the trigger hold
function must be on). The maximum trigger
hold time is set at 4.0 seconds after the trigger hold delay time. For example, if a trigger
hold delay time of 2.0 seconds is defined,
and the operator held the trigger in for more
than 6.0 seconds, the trigger hold function
would not be in effect and the wire feeder
would stop when the trigger is released.
• When the Setup push button is pressed
again, the menu repeats to the first menu
selection of run-in wire speed selection.
Trigger Program Select
• If the Setup push button is pressed, the unit
allows Trigger Program Select to be disabled or enabled.
The upper display shows “TSEL”. Lower display shows “On” or “Off”. The Adjust Control
is used to select either “On” or “Off”.
Trigger Program Select allows the operator to
select programs by clicking the trigger (pulling
and releasing the trigger in a maximum of 0.2
seconds). The feeder will switch between any
programs that have a minimum of 0.2 seconds of preflow time set in the weld sequence.
If programs 1 and 3 have a minimum of 0.2
seconds of preflow time, clicking the trigger
will toggle between programs 1 and 3. If programs 1, 2, and 4 have a minimum of 0.2 seconds of preflow time, clicking the trigger will
switch from 1 to 2 to 4 to 1 to 2. Any combination of programs may be used. Trigger Program Select cannot be used while welding or
with Dual Schedule.
Process Select
Process selection indicated by ”PROS” in the
upper display is set to either ”VOLT” or ”TRIM”
in the lower display. Each program can be selected be be a MIG program indicated by
”VOLT” or a pulsing program indicated by
”TRIM”.
Range Locks
Range locks are indicated by “LOCK” in the
upper display for wire speed or “LOCK” in the
lower display for voltage range. In a MIG program, the voltage range lock ranges from 0 to
10 volts. In a pulse program, the trim range
lock ranges from 0 to 100. The wire feed
speed range lock ranges for a standard speed
motor are 0 − 350 ipm (0 − 8.89 mpm) and for
a low speed motor 0 −100 ipm (0 − 2.54 mpm).
Locks are program dependent and wire
speed is independent from voltage or trim.
Wire Feed Speed Units
Wire feed speed setting indicated by “WFS” in
the upper display is set to “IPM” inches−per−
minute or ”MPM” meters−per−minute. This
setting is independent of the program selected.
OPT1
• If the Setup push button is pressed, the unit
allows OPT1 to be disabled or enabled.
The upper display shows “OPT1”. Lower display shows “On” or “Off”. The Adjust Control
is used to select either “On” or “Off”.
“OPT1” is used by the Water Flow Shutdown
Option to stop the weld sequence if water flow
to a water cooled gun is interrupted. A closed
set of contacts between pins 1 and 2 of RC26
on Interface Board (PC20) will allow feeder to
operate normally. Opening the contacts will
stop the weld sequence and display “ERR” in
the upper display and “OPT1” in the lower display.
OM-230 299 Page 27
5-10 Auxiliary Menus (Continued)
OPT2
• If the Setup push button is pressed, the unit
allows OPT2 to be disabled or enabled.
The upper display shows “OPT2”. Lower display shows “On” or “Off”. The Adjust Control
is used to select either “On” or “Off”.
“OPT2” is a second input that may be used
with an external device, such as a gas flow
switch, to end the weld sequence. The gas
flow switch may be used to stop the weld sequence if shielding gas flow to the gun is interrupted. A closed set of contacts between pins
1 and 2 of RC24 on Interface Board (PC20)
will allow feeder to operate normally. Opening
the contacts will stop the weld sequence and
display “ERR” in the upper display and
“OPT2” in the lower display.
Display Hold
Display hold indicated by ”DISP” in the upper
display is set to “OFF” or “HOLD” in the lower
display. When ”HOLD” is selected, the unit will
hold the last weld information for 5 seconds
following weld termination. If any front panel
push button is pressed, or if the Adjust control
is activated, the display hold feature is terminated.
Software Revision Level
• If the Setup push button is pressed, the unit
displays the software version being used by
the interface PCB (PC20).
• When the Setup button is pressed again, the
menu repeats.
Code
Upon leaving the auxiliary menu, the user is
asked if a password code indicated by
“CODE” in the top display should be activated.
By default the code is off, indicated by “OFF”
in the lower display. The user may enter a numerical password between 0 and 999 by turning the Adjust control. When the user re−enters the auxiliary menu, the password code
must be selected to gain access to the auxiliary menu. A failed attempt return the user to the
weld screen and a counter is incremented. A
counter in the program display shows the
number of incorrect attempts. The user has
five attempts to enter the correct password
code before being locked out of the auxiliary
menu, indicated by “LOCK” in the lower display . The power may be cycled to continue
welding but the user will remained locked out
of the auxiliary menu. Pressing the Program,
Sequence, upper display, and Set−up push
buttons simultaneously, the counter can be reset in the weld screen. Resetting the counter
is indicated by “CODE” in the upper display
and “RSET” in the lower display. Pressing the
Program, Sequence, upper display, and Set−
up push buttons simultaneously again will allow the user to reset the unit to the factory defaults, indicated by “WIPE” in the upper display. Resetting the unit will also turn off the
password code feature.
5-11. Jog/Purge
1
Jog/Purge Switch
Pressing the Jog switch allows the
operator to jog wire without energizing the weld power or gas valve circuit.
• Jog speed can be adjusted by the
Adjust control when the unit is
jogging wire. The unit displays jog
speed when the unit is being
jogged.
• Pressing the Purge switch allows
the operator to purge gas lines
before welding and to preset gas
pressure at the regulator.
2
2
Adjust Control
1
802 807-A
OM-230 299 Page 28
SECTION 6 − SETTING SEQUENCE PARAMETERS
6-1. Sequence Parameters In A Program
. For more information on
Sequence Push Button see
Section 5-9.
Sequence
If time is set to zero in Weld
sequence, welding continues until
gun trigger is released.
Parameters
Volts
IPM
1. Preflow
If time is set to zero in any timed
sequence except Weld, the
sequence is skipped.
Seconds
0-9.9
2. Run-In
X
3. Start
X
X
0.00-5.00
4. Weld
X
X
0-100.0
5. Crater
X
X
0-5.00
6. Burnback
X
0-0.25
7. Postflow
0-9.9
X = Setting available.
Weld Time
Crater
Time
Preflow
Time
Burnback
Time
Start
Time
Postflow
Time
Time
Burnback
Preflow
Trigger
Pressed
Run-In Start
Weld
Crater
Postflow Sequence
End
Trigger
Released
OM-230 299 Page 29
SECTION 7 − SETTING DUAL SCHEDULE PARAMETERS
7-1. Optional Dual Schedule Switch Diagrams
1
1
1
DSS-9
2
2
1
2
DSS-8
3
1
2
TR
B
A
2
3
A
4
B
OM-230 299 Page 30
4
Maint 2P (Maintained-Contact
2-Pole Switch)
Maint 1P (Maintained-Contact
1-Pole Switch)
SECTION 8 − MAINTENANCE AND TROUBLESHOOTING
8-1. Routine Maintenance
Y Disconnect power before maintaining.
n = Check
~ = Clean
l = Replace
Reference
Every
3
Months
Section 4-5,
4-6
l Unreadable Labels
~ Weld Terminals
nl Weld Cable
nl Motor Brush
Section 4-5,
4-6
n 14-Pin Cord
Every
6
Months
n Gas Hose and Fittings
n Gun Cable
Section
4-11
Or
~ Inside Unit
~ Drive Rolls
8-2. Brush Inspection And Replacement
Y Do not disassemble motor field magnets or injury/equipment damage may
occur.
1
Motor
2
Brush Cap
Remove brush cap.
3
Brush
Replace brush if it becomes chipped or broken, or if less than 1/4 in. (6.4 mm) of brush
material remains. Do not include spring boss
as part of the 1/4 in. measurement.
Install brush so that curved surface on end of
brush matches curve of motor, and secure
with cap.
1
3
2
Tools Needed:
137 390-B
OM-230 299 Page 31
8-3. Diagnostics
1
2
3
4
Wrapper
Motor Control Board PC1
LED3
DIP Switch S1
. There is a two-position
DIP switch S1 located
on motor control board
PC1. These switches
are factory-set in the
off position and must
remain in that position
for the unit to operate
correctly.
2
3
4
1
Front panel is shown removed for purpose of
illustration only. In actual use, front panel
would be in place.
Ref. 802 687
The following error messages are shown on the
upper and lower displays to indicate specific errors.
Explanations are in the text below:
ERR
ERR
ERR
ERR
ERR
ERR
COM1
TRG1
TCH1
MTR1
OPT1
OPT2
Indicates a
communication
error.
Indicates a trigger
error.
LED3-Related Error Indications
Error conditions are indicated by LED3 on
PC1. To view LED3, turn Off unit, remove
wrapper, and turn unit On. LED3 is most easily
observed from the left side of the unit.
The LED blinks in a 2.5 second cycle. The
number of blinks in this period indicates the
type of error.
The priority of the errors is related to the number of blinks indicating the error. The more
blinks, the more severe the error (motor error
is top priority). A higher priority error overrides
a lower one (if a motor error and a communication error existed, the light would blink four
times for the motor error).
Since blink On time and blink Off time are
equal in a four-blink cycle, the four−blink sequence appears as a constant blink.
1 blink = Communication Error
2 blinks = Trigger Error
OM-230 299 Page 32
Indicates a
tachometer error.
Indicates a motor
error.
3 blinks = Tach Error
4 blinks = Motor Error
ERR COM1
• The communication error occurs 2.5 seconds after a loss of communication between
the motor and front panel boards. The user
may continue to weld with this error. The error may be cleared by resetting the unit (see
Section 5-10).
ERR TRG1
• The trigger error occurs if the user has the
trigger held for more than two minutes without striking an arc (providing current override is not enabled), or if the user holds the
trigger past the postflow phase in a timed
weld. This error also occurs if the trigger is
held when the feeder is powered up. The error may be cleared by releasing the trigger.
ERR TCH1
• The tach error occurs 2 seconds after the
loss of tachometer feedback. The user may
No gas flow
detected.
Optional error
condition
continue to weld with this error. The motor
speed is regulated through the monitoring of
voltage and current.
ERR MTR1
• The motor error indicates that the motor
has been drawing too much current for too
long. To remedy this, reduce the wire feed
speed or the wire feeder torque load/duty
cycle.
ERR OPT1
• The optional 1 error indicates no coolant
flow in water flow switch option. The error
may be reset by reestablishing coolant flow
to the gun, and then pressing any button on
front panel.
ERR OPT2
• The optional 2 error indicates a problem
with optional device connected to RC24 on
Interface Board (PC20). The error may be
reset by correcting the problem, and then
pressing any button on front panel.
8-4. Troubleshooting
Y Disconnect power before troubleshooting
Trouble
Wire feeds, shielding gas flows, but
electrode wire is not energized.
Remedy
Check cable connections. Check cables for continuity, and repair or replace cables if necessary
(see Section 4-6).
Wire feeder is on, display does not light Check and reset circuit breaker at welding power source.
up, motor does not run, gas valve and
welding power source contactor do not
pull in.
Electrode wire feeding stops or feeds
erratically during welding.
welding
Check gun trigger connection. See gun Owner’s Manual.
Check gun trigger. See gun Owner’s Manual.
Readjust hub tension and drive roll pressure (see Section 4-15).
Change to correct size drive roll (see Section 4-11 and Table 10-1).
Clean or replace dirty or worn drive roll.
Incorrect size or worn wire guides.
Replace contact tip or liner. See gun Owner’s Manual.
Remove weld spatter or foreign matter from around nozzle opening.
Check brushes in drive motor. If brush length is less than 1/4 inch, replace brushes.
Have Factory Authorized Service Agency check drive motor or motor control board PC1.
Motor runs slowly.
Check for correct input voltage.
Wire feeder power is on, displays light
up, feeder jogs, purges, but unit is inoperative.
Check welding gun trigger leads for continuity, and repair leads or replace gun.
When triggered wire feeds but no gas,
no contactor.
If the welding arc does not establish in 3 seconds after the gun trigger is activated the unit will feed
wire, but turns off contactor and gas valve. If the gun trigger is still activated after two minutes, the
wire will stop feeding.
OM-230 299 Page 33
SECTION 9 − ELECTRICAL DIAGRAM
Figure 9-1. Circuit Diagram
OM-1500-12 Page 34
200 592-H
Notes
OM-230 299 Page 35
SECTION 10 − PARTS LIST
. Hardware is common and
7
6
11
Fig 10-6
10
9
8
14
23
18
18
Fig 10-4,5
28
29
27
30
26
25
24
22
20
19
21
31
Fig 10-2
1
2
15
16
17
Fig 10-3
13
12
2
7
3
5
4
not available unless listed.
Figure 10-1. Main Assembly
OM-230 299 Page 36
804 770-A
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Model
16
12
Figure 10-1. Main Assembly
. . . 1 . . . . . . . . . . . . See Note
. . . 2 . . . . . . . . . . . . . 201 319
. . . 2 . . . . . . . . . . . . . 201 320
. . . . . . PLG37,38 . . 047 636
. . . . . . . . . . . . . . . . . . . 079 739
. . . . . . . . . . . . . . . . . . . 163 520
. . . 3 . . . . . . . . . . . . . 139 600
. . . 3 . . . . . . . . . . . . . 139 599
. . . 4 . . . . . . . . . . . . . 600 324
. . . 5 . . . . . . . . . . . . . 149 884
. . . 5 . . . . . . . . . . . . . 080 947
. . . 6 . . . . . . . . . . . . . 132 053
. . . 7 . . . . . . . . . . . . . 602 243
. . . 8 . . . . . . . . . . . . . 602 213
. . . 9 . . . . . . . . . . . . . 601 872
. . . 10 . . . . . . . . . . Figure 10-6
. . . 11 . . . . . . . . . . . . . 149 838
. . . 11 . . . . . . . . . . . . . 149 839
. . . 11 . . . . . . . . . . . . . 078 264
. . . 11 . . . . . . . . . . . . . 079 216
. . . 12 . . . . . . . . . . . . . 075 078
. . . 12 . . . . . . . . . . . . . 079 217
. . . 13 . . . . . . . . . . Figure 10-3
. . . 14 . . RC37 . . . . 047 637
. . . 15 . . PLG46 . . . . 115 090
. . . 16 . . PLG44 . . . 167 640
. . . 17 . . PLG4 . . . . 136 810
. . . 18 . . . . . . . . . . . . . 203 314
. . . . . . . . RC13 . . . . 080 328
. . . . . . . . . . . . . . . . . . . 079 531
. . . . . . . . . . . . . . . . . . . 604 571
. . . . . . . . PLG6 . . . . . 115 094
. . . 19 . . PLG5 . . . . 131 204
. . . 20 . . PLG45 . . . 131 203
. . . 21 . . . . . . . . . . . . . 220 805
. . . 22 . . . GS1 . . . . . 228 035
. . . . . . . . . . . . . . . . . . . 134 834
. . . 23 . . . . . . . . . . . . . 229 286
. . . 24 . . . . . . . . . . . . . 156 243
. . . 25 . . . . . . . . . . . . . 159 360
. . . 26 . . . . . . . . . . . . . 219 095
. . . 27 . . . . . . . . . . . . . 229 290
. . . 27 . . . . . . . . . . . . . 229 289
. . . 28 . . . . . . . . . . . . . 145 639
. . . 29 . . . . . . . . . . . . . 159 646
. . . 30 . . . . . . . . . . . . . 159 647
. . . 31 . . . . . . . . . . . . . . 211 989
. . Control Box, (Figure 10-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Cable, Interconnecting (consisting of) . . . . . . . . . . . . . . . . . . . . . . . 1
. . Cable, Interconnecting (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Connector & Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Connector, Circ Clamp Str Rlf Sz 17.20 . . . . . . . . . . . . . . . . . . . . 2 . . . . 2
. . . . Cable, Port No. 18-14 11/C (order by ft) . . . . . . . . . . . . . . . . . . . 17Ft . . 21Ft
. . Hose, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Hose, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Cable, Weld Cop Strd No. 4/0 (order by ft) . . . . . . . . . . . . . . . . . . 30Ft . . 34Ft
. . Bracket, Spring Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Bracket, Spring Retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Screw, Cap Stl Hexhd .375-16 X 1.500 Lg . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . Washer, Flat Stl Std .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 . . . . 8
. . Washer, Lock Stl Split .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . Nut, Stl Hex Full .375-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . Support, Hub & Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Pipe Post, 4ft W/Base (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Pipe Post, 6ft W/Base (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Pipe Post, 4ft W/Base (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Pipe Post, 6ft W/Base (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . Pipe Post, 4ft W/O Base (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Pipe Post, 6ft W/O Base (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Boom Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Pins & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Cable, Trigger (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . Connector W/Sockets, Free Hanging . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . . . Connector, Circ Clamp Str Rlf Size 11 Amp 206358-2 . . . . . . . . 2 . . . . 2
. . . . Cable, 18/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Ft . . 2Ft
. . . . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Connector & Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Nut, Nyl Hex Jam .750npst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Valve, 34VDC 1Way .750−14 Thd 2mm Orf 100PSI . . . . . . . . . . . 1 . . . . 1
. . Hose, Sae .187 Id X .410 Od (order by ft) . . . . . . . . . . . . . . . . . . . 2Ft . . 2Ft
. . Cover, Motor & Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Clamp, Motor Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Insulator, Screw Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . 4
. . Spacer, Motor Clamp (Used With Standard Speed Motor) . . . . . . 1 . . . . 1
. . Drive Assembly, Wire (Standard Speed) (Figure 10-4,5) . . . . . . . 1 . . . . 1
. . Drive Assembly, Wire (Low Speed) (Figure 10-4,5) (optional) . . . 1 . . . . 1
. . Spacer, Motor Clamp (Used With Low Speed Motor) . . . . . . . . . . 1 . . . . 1
. . Clamp, Motor Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Insulator, Motor Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
. . Fitting, W/Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . 1
Note: When ordering Control Box contact factory service department for proper number.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-230 299 Page 37
. Hardware is common and
1
not available unless listed.
4
3
2
5
8
7
6
9
23
22
18
20
19
13
12
11
10
21
17
12
15
13
16
802 870−A
Figure 10-2. Control Box
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-2. Control Box (Figure 10-1 Item 1)
. . . 1 . . . . . . . . . . . . . . . 200 562 . . Wrapper, Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 2 . . . . . . . . . . . . . . . . . . . . . . . . . . Nameplate (Order by Model and Serial Number) . . . . . . . . . . . . . . . . . . . 1
. . . 3 . . . . PC21 . . . . . 200 693 . . Circuit Card Assy, Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . PC20 . . . . . 224 322 . . Circuit Card Assy, Display W/Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 5 . . . . . . . . . . . . . . . 047 637 . . Housing Rcpt+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 6 . . . . . . . . . . . . . . . 200 551 . . Enclosure, Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 7 . . . . . . . . . . . . . . . 134 201 . . Stand-Off Support, Pc Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . 8 . . . . . . . . . . . . . . . 024 376 . . Plug, 0.625 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 9 . . . . . . . . . . . . . . . 148 253 . . Bushing, Snap−In Nyl 1.375 Id X 1.750 Mtg Hole . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . 204 911 . . Cable, Power (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 10 . . . PLG12 . . . . 141 162 . . . . Housing Plug+Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . PLG3 . . . . . 115 093 . . . . Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 11 . . . . . . . . . . . . . . . 079 739 . . . . Conn, Circ Cpc Clamp Str Rlf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 12 . . . . . . . . . . . . . . . 163 519 . . . . Cable, Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5 Ft
. . . 13 . . . . . . . . . . . . . . . 139 041 . . . . Strain Relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
OM-230 299 Page 38
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-2. Control Box (Figure 10-1 Item 1) (Continued)
. . . 15 . . . . . . . . . . . . . . .
. . . 16 . . . . . . . . . . . . . . .
. . . 17 . . . . PC1 . . . . .
. . . 17 . . . . PC1 . . . . .
. . . 18 . . . . . S1 . . . . . .
. . . 19 . . . . . . . . . . . . . . .
. . . 20 . . . . . S2 . . . . . .
. . . 21 . . . . . . . . . . . . . . .
. . . 22 . . . . . . . . . . . . . . .
. . . 23 . . . . . . . . . . . . . . .
. . . . . . . . . PLG35 . . . .
. . . . . . . . . PLG44 . . . .
. . . . . . . . PLG37,38 . . .
. . . . . . . . RC37,40 . . .
. . . . . . . . PLG6,36 . . .
. . . . . . . . . PLG46 . . . .
. . . . . . . . PLG11,61 . . .
. . . . . . . . . PLG45 . . . .
. . . . . . . . . . PLG1 . . . . .
. . . . . . . . PLG4,34 . . .
. . . . . . . . PLG7,27 . . .
. . . . . . . . . PLG10 . . . .
070 371
200 553
224 307
224 337
111 997
200 559
200 295
202 587
000 527
213 134
131 204
148 389
047 636
047 637
115 094
115 090
131 005
131 203
202 592
136 810
115 091
130 203
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
..
Bushing, Snap−in Nyl .937 Id X 1.125 Mtg Hole . . . . . . . . . . . . . . . . . . . .
Bracket, Control Box Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Card Assy, Motor Control (Standard Speed Motor) . . . . . . . . . . .
Circuit Card Assy, Motor Control (Low Speed Motor) . . . . . . . . . . . . . . . .
Switch, Rocker Spst 10A 250 VAC On-Off . . . . . . . . . . . . . . . . . . . . . . . . .
Panel, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch, Rocker Spdt 15A 12V (On)-Off-(On) . . . . . . . . . . . . . . . . . . . . . . .
Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plug, 0.875 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Knob, Encoder 1.670 Dia X .250 Id Push On W/Spring . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Pins, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug Pins+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing Plug+Skts, (service kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-230 299 Page 39
16
8
15
14
13
9
12
11
9
10
8
7
6
5
2
26
27
23
22
26
25
18
24
21
20
17
19
3
4
. Hardware is common and
1
28
not available unless listed.
804 729-A
Figure 10-3. Boom Assembly
OM-230 299 Page 40
Item
No.
Part
No.
Description
Quantity
Model
12
16
Figure 10-3. Boom Assembly (Figure 10-1 Item 13)
. . . 1 . . . . 000 527 . . Plug, 0.875 Inch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 2 . . . . 229 276 . . Boom, Single 12Ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 2 . . . . 229 277 . . Boom, Single 16Ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 3 . . . . 079 665 . . Guide, Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 3 . . . . 080 811 . . Guide, Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 4 . . . . 079 664 . . Guide, Wire Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 5 . . . . 139 633 . . Liner, Monocoil 3/32-1/8 Wire X 15.687 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 6 . . . . 073 742 . . Pin, Clevis .750 Od X 2.156 Lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 7 . . . . 073 741 . . Clevis, .812 Yoke 6.062 Lg .750-16thd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 8 . . . . 079 029 . . Nut, Stl Hex Full Fnsh .750-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 9 . . . . 075 462 . . Shaft, Boom Counterbalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 10 . . . . 602 250 . . Washer, Flat Stl Sae .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 11 . . . . 079 020 . . Nut, Stl Hex Elastic Stop .750-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 12 . . . . 149 858 . . Spring, Cprsn 3.750 Od X .625 Wire X 36.000 . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 12 . . . . 080 723 . . Spring, Cprsn 3.750 Od X .687 Wire X 33.750 . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 13 . . . . 150 258 . . Retainer, Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 14 . . . . 024 605 . . Bearing, Ball Thr Sgl Row .750 X 1.625 X .625 . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 15 . . . . 075 101 . . Nut, Stl Hex Special .750-16 X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 16 . . . . 079 030 . . Washer, Lock Stl Ext Tooth .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 17 . . . . +174 754 . . Base, Swivel Boom (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 080 157 . . . . . Fitting, Grease 1/8npt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 18 . . . . 174 688 . . Bracket, Mtg Control Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 142 804 . . Label, Swingarc Caution Heavy Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 134 327 . . Label, Warning General Precautionary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 19 . . . . 073 666 . . Bolt, Mach Stl Hexhd .750-16 X 2.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 20 . . . . 047 224 . . Knob, T-bar .500-13 Thd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 21 . . . . 602 246 . . Washer, Flat Stl Std .500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 22 . . . . 079 667 . . Pipe, Plstc .500 X 133.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 22 . . . . 080 812 . . Pipe, Plstc .500 X 181.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 23 . . . . 079 632 . . Bolt, U Stl .250-20 X .875 Wide X 1.375 Deep . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 24 . . . . 602 243 . . Washer, Flat Stl Std .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 25 . . . . 079 622 . . Washer, Shldr .381 Id X .750 Od . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 26 . . . . 010 313 . . Pin, Cotter Hair .072 X 1.437 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 27 . . . . 079 621 . . Pulley, V Sgl Grv . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . 28 . . . . 229 287 . . Guard, Motor Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 149 322 . . Clamp, Hose .405 − .485clp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
0
1
0
1
1
1
1
2
1
2
1
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
0
4
3
2
2
1
1
2
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
1
0
1
1
1
1
1
1
1
2
1
2
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
5
3
2
2
1
1
2
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
229 276
OM-230 299 Page 41
. Hardware is common and
not available unless listed.
See Table 8-1 For
Drive Roll & Wire Guide Kits
21
10
20
2
14
9
8
7
13
6
11
12
5
1
4
3
20
23
2
19
18
21
24
22
15
16
17
804 733-A
Figure 10-4. Drive Assembly, Wire
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Figure 10-4. Drive Assembly, Wire (Figure 10-1 Item 27)
. . . 1 . . . . . . . . . . . . . . . 230 248 . . Kit, Swing Arm Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 2 . . . . . . . . . . . . . . . 219 126 . . Screw, Shld Stl Sch .375−16 X .500 X 1.000 Shld . . . . . . . . . . . . . . . . . . . 2
. . . 3 . . . . . . . . . . . . . . . 230 244 . . Kit, Insulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . . . . . . . . . . 601 941 . . Screw, 250−20x1.75 Hexwhd.61D Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 5 . . . . . . . . . . . . . . . 219 132 . . Screw, 375−16x2.00 Hexwhd.81D Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 6 . . . . . . . . . . . . . . . 229 412 . . Gear, Spur W/Insulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 7 . . . . . . . . . . . . . . . 079 625 . . Washer, Wave .500 Idx0.750 Odx.015t Stl Lbs . . . . . . . . . . . . . . . . . . . . . . 1
. . . 8 . . . . . . . . . . . . . . . 605 308 . . Ring, Rtng Ext .500 Shaft X .035 Thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 9 . . . . . . . . . . . . . . . 108 943 . . Screw, 250−20x1.50 Hexwhd.61D Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 10 . . . . . . . . . . . . . . . 219 133 . . Screw, 375−16x1.50 Hexwhd.81D Pld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 11 . . . . . . . . . . . . . . . 602 241 . . Washer, Flat .281 Idx0.625 Odx.065t Stl Pld Ansi.250 . . . . . . . . . . . . . . . . 1
. . . 12 . . . . . . . . . . . . . . . 227 711 . . Screw, 250−20x .50 Button Hd−Soc Stl Pld Lkg Patch . . . . . . . . . . . . . . . 1
. . . 13 . . . . . . . . . . . . . . . 092 865 . . Key, Stl .1215/.1230 X .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 14 . . . . . . . . . . . . . . . 230 238 . . Kit, Pressure Door Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 15 . . . . . . . . . . . . . . . 230 326 . . Kit, Power Pin Clamp Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 16 . . . . . . . . . . . . . . . 219 136 . . Lock, Pin Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 17 . . . . . . . . . . . . . . . 219 096 . . Knob, Tri−Lobe W/.375−16 Stud 2.500 Lg Blk . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 18 . . . . . . . . . . . . . . . 219 125 . . Screw, 010−32x .50 Soc Hd−Hex Pln . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 19 . . . . . . . . . . . . . . . 219 091 . . Holder, Guide Intermediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 20 . . . . . . . . . . . . . . . 229 563 . . Washer, Cap .500 Id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 21 . . . . . . . . . . . . . . . 198 425 . . Cap, Finishing 1.19 X .37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 22 . . . . . . . . . . . . . . . 230 245 . . Kit, Drive Roll Carrier Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 23 . . . . . . . . . . . . . . . 219 130 . . Screw, Set 250−20x .18 Conept Sch Stl Pln . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 24 . . . . . . . . . . . . . . . 601 965 . . Screw, 375−16x1.00 Hex Hd−Pln Gr5 Pld . . . . . . . . . . . . . . . . . . . . . . . . . . 1
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-230 299 Page 42
. Hardware is common and
not available unless listed.
1
3
4
5
2
6
7
804 734-A
Figure 10-5. Drive Assembly With Motor
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Figure 10-5. Drive Assembly With Motor (Figure 10-1 Item 27)
. . . 1 . . . . . . . . . . . . . . . 223 252 . .
. . . 2 . . . . . . . . . . . . . . . 190 742 . .
. . . 3 . . . . . . . . . . . . . . . 223 253 . .
. . . 4 . . . . . . . . . . . . . . . 223 254 . .
. . . 5 . . . . . M1 . . . . . . 219 088 . .
. . . . . . . . . . . . . . . . . . . . . 153 491 . .
. . . 5 . . . . . M1 . . . . . . 219 087 . .
................................
. . . . . . . . . . . . . . . . . . . . . 153 491 . .
. . . 6 . . . . . . . . . . . . Figure 10-4 . .
. . . 7 . . . . . . . . . . . . . . . 219 103 . .
. . . 7 . . . . . . . . . . . . . . . 220 012 . .
Tachometer, Optical Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screw, 006−32x .31 Pan Hd Phl Stl Pld (Low Speed Motor) . . . . . . . . . .
Adapter, Optical Encoder (Standard Speed Motor) . . . . . . . . . . . . . . . . . .
Adapter, Optical Encoder (Low Speed Motor) . . . . . . . . . . . . . . . . . . . . . .
Motor (Low Speed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kit, Brush Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor, Gear .09HP 24VDC 273RPM 29:1 Ratio
(Standard Speed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kit, Brush Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Assembly, Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screw, 010−32x .75 Flathd−Soc Stl Pln (Low Speed) . . . . . . . . . . . . . . .
Screw, 250−28x .62 Button Soc−Hd Zinc (Standard Speed) . . . . . . . . . .
1
1
1
1
1
1
1
1
1
4
4
OM-230 299 Page 43
. Hardware is common and
not available unless listed.
1
2
6
3
5
4
7*
9
3
*Includes Item 8
8
2
10
11
12
13
14
ST-146 339-B
Figure 10-6. Support, Hub & Reel
Item
No.
Part
No.
Description
Quantity
Figure 10-6. Support, Hub & Reel (Figure 10-1 Item 10)
. . . . . . 1 . . . . . . 142 399 . . Support, Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 2 . . . . . . 010 191 . . Washer, Fbr .656 Id X 1.500 Od X .125thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . 3 . . . . . . 058 628 . . Washer, Brake Stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . 4 . . . . . . 058 428 . . Hub, Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 5 . . . . . . 108 008 . . Reel, Wire 60 Lb (optional) (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 6 . . . . . . 124 900 . . . . Support, Reel Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 7 . . . . . +168 104 . . . . Retainer, Spool Support (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 8 . . . . . . 166 594 . . . . . . Label, Caution Falling Wire Reel Can Cause Damage . . . . . . . . . . . . . . . . . 1
. . . . . . 9 . . . . . . 168 103 . . . . Nut, Spanner Spool Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . 10 . . . . . . 057 971 . . Washer, Flat Stl Keyed 1.500dia X .125thk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . 11 . . . . . . 010 233 . . Spring, Cprsn .970 Od X .120 Wire X 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . 12 . . . . . . 605 941 . . Washer, Flat Stl .640 Id X 1.000 Od X 14ga Thk . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . 13 . . . . . . 136 684 . . Nut, Stl Slflkg Hex Reg .625-11 W/Nylon Insert . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . 14 . . . . . . 058 427 . . Ring, Retaining Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-230 299 Page 44
OM-230 299 Page 45
224873
224874
224875
224876
224877
224878
0.9 mm
1.0 mm
1.1−1.2 mm
1.3−1.4 mm
1.6 mm
1.8 mm
2.0 mm
2.4 mm
2.8 mm
.035 in.
.040 in.
.045−.047 in.
.052 in.
1/16 in.
(.062)
.068−.072 in.
5/64 in.
(.079)
3/32 in.
(.094)
7/64 in.
(.110)
3.2 mm
224872
0.8 mm
030 in.
1/8 in.
(.125)
224871
PD-V Kit
0.6 mm
Metric
PD-V for Hard Wire
222501
222500
222499
222498
222497
222496
222495
222494
PD-V
Drive
Roll
223098
223098
223097
223097
223097
223096
223096
223096
PD
Continous
Guide
(1 kit or 4 rolls & 1 guide required)
.023−.025 in.
Fraction
Wire Size
300041
300040
300039
PD-U Kit
227772
227770
227768
PD-U
Drive
Roll
223101
(Blue)
223100
(White)
223099
(Red)
PD
Continous
Guide
(1 kit or 4 rolls & 1 guide required)
PD-U for Aluminum
219109
219109
219109
219109
219108
219108
219108
219108
219108
219108
219108
219108
Inlet
Guide
Old Style
PD and
223516
223516
223516
223516
223515
223515
223515
223515
223515
223515
223515
223515
Intermediate
Guide
223518
223518
223518
223518
223517
223517
223517
223517
223517
223517
223517
223517
Exit
Guide
Rolls (1 each required)
Guides for Old Style Drive
053699
053698
053697
053700
053695
087130
V Groove
Table 10-1. PD (Precision Drive) and Non-PD (Old-Style) Drive Rolls and Guides
053707
053705
053703
053704
053706
053702
053701
072000
U Groove
132963
132962
132961
132960
132959
13295
132955
132956
132957
132958
VK Groove
( 4 required)
Standard Drive Rolls
053712
053711
053709
053710
053708
083490
083489
UC Groove
Notes
Effective January 1, 2006
(Equipment with a serial number preface of “LG” or newer)
Warranty Questions?
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY − Subject to the terms and conditions
* Induction Heating Coils and Blankets, Cables, and
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to
Non-Electronic Controls
its original retail purchaser that new Miller equipment sold after
* APT & SAF Model Plasma Cutting Torches
the effective date of this limited warranty is free of defects in
* Remote Controls
material and workmanship at the time it is shipped by Miller. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
* Accessory (Kits)
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
* Replacement Parts (No labor)
WARRANTIES OF MERCHANTABILITY AND FITNESS.
* Spoolmate Spoolguns
Within the warranty periods listed below, Miller will repair or
* Canvas Covers
replace any warranted parts or components that fail due to such
defects in material or workmanship. Miller must be notified in
writing within thirty (30) days of such defect or failure, at which
time Miller will provide instructions on the warranty claim
procedures to be followed.
Miller shall honor warranty claims on warranted equipment listed
below in the event of such a failure within the warranty time
periods. All warranty time periods start on the date that the
equipment was delivered to the original retail purchaser, or one
year after the equipment is sent to a North American distributor
or eighteen months after the equipment is sent to an
International distributor.
1.
5 Years Parts — 3 Years Labor
2.
3 Years — Parts and Labor
*
*
*
*
*
*
*
*
*
3.
Original main power rectifiers
Transformer/Rectifier Power Sources
Plasma Arc Cutting Power Sources
Process Controllers
Semi-Automatic and Automatic Wire Feeders
Inverter Power Sources (Unless Otherwise Stated)
Water Coolant Systems (Integrated)
Intellitig
Engine Driven Welding Generators
(NOTE: Engines are warranted separately by the
engine manufacturer.)
1 Year — Parts and Labor Unless Specified
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Motor Driven Guns (w/exception of Spoolmate
Spoolguns)
Positioners and Controllers
Automatic Motion Devices
RFCS Foot Controls
Induction Heating Power Sources, Coolers, and
Electronic
Controls/Recorders
Water Coolant Systems (Non-Integrated)
Flowgauge and Flowmeter Regulators (No Labor)
HF Units
Grids
Spot Welders
Load Banks
Arc Stud Power Sources & Arc Stud Guns
Racks
Running Gear/Trailers
Plasma Cutting Torches (except APT & SAF
Models)
Field Options
(NOTE: Field options are covered under True Blue®
for the remaining warranty period of the product they
are installed in, or for a minimum of one year —
whichever is greater.)
Bernard-Branded Mig Guns (No Labor)
Weldcraft-Branded TIG Torches (No Labor)
Subarc Wire Drive Assemblies
4.
6 Months — Batteries
5.
90 Days — Parts
*
MIG Guns/TIG Torches and Subarc (SAW) Guns
Miller’s True Blue® Limited Warranty shall not apply to:
1.
Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, slip rings, relays
or parts that fail due to normal wear. (Exception:
brushes, slip rings, and relays are covered on Bobcat,
Trailblazer, and Legend models.)
2.
Items furnished by Miller, but manufactured by others, such
as engines or trade accessories. These items are covered
by the manufacturer’s warranty, if any.
3.
Equipment that has been modified by any party other than
Miller, or equipment that has been improperly installed,
improperly operated or misused based upon industry
standards, or equipment which has not had reasonable and
necessary maintenance, or equipment which has been
used for operation outside of the specifications for the
equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the goods at
customer’s risk and expense. Miller’s option of repair or
replacement will be F.O.B., Factory at Appleton, Wisconsin, or
F.O.B. at a Miller authorized service facility as determined by
Miller. Therefore no compensation or reimbursement for
transportation costs of any kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT,
INDIRECT,
SPECIAL,
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY
OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION
OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING,
INCLUDING
ANY
IMPLIED
WARRANTY
OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL EQUIPMENT
FURNISHED BY MILLER IS EXCLUDED AND DISCLAIMED
BY MILLER.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available,
but may vary from province to province.
miller_warr 2006−01
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
PRINTED IN USA
© 2006 Miller Electric Mfg. Co. 2006−01
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
International Headquarters−USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
European Headquarters −
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
www.MillerWelds.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising