Miller | MG000000G | Owner Manual | Miller SUBARC HINGE MOUNTING BRACKET (301136) User manual

Miller SUBARC HINGE MOUNTING BRACKET (301136) User manual
OWNER’S MANUAL
OM-274912A
2016−04
For SubArc Hinge Mounting Bracket (301136)
1.
Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained in
the text.
DANGER ! - Indique une situation dangereuse qui, si elle
n’est pas évitée, entraînera la mort ou des blessures graves.
Les éventuels risques sont représentés par les symboles
joints ou expliqués dans le texte.
Beware of electric shock from wiring. Disconnect input power before installing this kit. Reinstall all panels and covers.
Attention aux décharges électriques au contact des câbles.
Couper l’alimentation électrique avant d’installer ce kit. Réinstaller tous les panneaux et couvercles.
Fsafe7 2013-10
Fsafe1 2013-10
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury. The possible hazards are
shown in the adjoining symbols or explained in the text.
Indique une situation dangereuse qui, si elle n’est pas évitée,
entraînera la mort ou des blessures graves. Les éventuels
risques sont représentés par les symboles joints ou expliqués dans le texte.
Wear safety glasses with side shields.
Porter des lunettes de sécurité avec écrans latéraux.
Fsafe8 2013-10
Fsafe2 2013-10
NOTICE
Indicates statements not related to personal injury.
Signale des consignes non associées aux dommages corporels.
Indicates special instructions.
Fournit des instructions spéciales.
Fsafe3 2013-10
Have only trained and qualified persons install, operate, or
service this unit. Read the safety information at the beginning of these instructions and in each section. Call your distributor if you do not understand the directions. For WELDING SAFETY and EMF information, read owner’s manual(s).
Ne confiez l’installation, l’exploitation ou l’entretien de cet
appareil qu’à des personnes compétentes et qualifiées. Lire
les directives de sécurité au début de ces instructions et
dans chaque section. Appeler votre distributeur si vous
ne comprenez pas les directives. Lire le(s) manuel(s)
d’utilisateur pour des renseignements sur la SÉCURITÉ
DE SOUDAGE et les champs électromagnétiques.
Fsafe15 2013-10
CALIFORNIA PROPOSITION 65 WARNINGS
Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some
cases, cancer. (California Health & Safety Code Section 25249.5 et seq.) This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, or other reproductive harm. Wash hands after use.
Les équipements de soudage et de coupage produisent des fumées et des gaz qui contiennent des produits chimiques dont l’État de Californie reconnaît qu’ils provoquent des malformations congénitales et, dans certains cas, des cancers. (Code de santé et de sécurité de Californie, chapitre
25249.5 et suivants) Ce produit contient des produits chimiques, notamment du plomb, dont l’État de Californie reconnaît qu’ils provoquent des
cancers, des malformations congénitales ou d’autres problèmes de procréation. Se laver les mains après utilisation.
Fsafe4 2013-10
2.
Description
The mounting hinge bracket is designed to provide support for Miller® SubArc welding equipment or other welding equipment. This unit is intended to be
mounted on a fixed arm.
Contact the manufacturer of the fixed arm to ensure it is capable of supporting the weight of the mounting hinged bracket and attached
equipment.
3.
Specifications
Product Type
Mounting Hinge Bracket
4.
Overall Dimensions
Weight
16 in. in. X 10.125 in. X 10 in.
66 lbs
(406 mm x 257 mm x 254 mm)
(30 kg)
Tools Needed
3/8 in.
7/16, 9/16 in.
5.
Dimensions
16.000 in.
(406 mm)
Top View
90° Position
10.125 in.
(257 mm)
10.000 in.
(254 mm)
Back View
90° Position
Front View
90° Position
15.000 in.
(381 mm)
7.125 in.
(181 mm)
Top View
180° Position
275 557-A
OM-274912 Page 2
6.
Mounting Hole Dimensions
!
10.750 in.
(273 mm)
10.000 in.
(254 mm)
6 x ∅ .313 in.
(8 mm )
Turn Off power for boom and
column and all other electrical
equipment before working on
unit.
. The
5.000 in.
(127 mm)
mounting hinge bracket is
provided with 1/2-13 x 2 in. socket
head cap screws for attaching the
bracket to a fixed arm or movable
slide. If desired, M12 x 51 hardware may be used. In this case the
holes should be threaded
accordingly.
4.331 in.
(110 mm)
1.969 in.
(50 mm)
8 x ∅ .313 in.
(8 mm )
1.969 in.
(50 mm)
4 x ∅ .531 in.
(13 mm )
6.000 in.
(152 mm)
2.500 in.
(64 mm)
4 x ∅ .531 in.
(13 mm )
4.331 in.
(110 mm)
2.500 in.
(64 mm)
8.500 in.
(216 mm)
275 558-A
OM-274912 Page 3
7.
Installation
5
7
!
Turn Off power for boom and
column and all other electrical
equipment before working on
unit.
1
Mounting Hinge Bracket
90° Position recommended.
1
2
1/2 - 13 x 2.00 in. Soc HD Cap
Screws
3
1/2 in. Lock Washers
4
1/2 in. Flat Washers
5
1/2 in. Hex Nuts
6
Locking Pin
Can be placed on top or bottom.
7
Knurled Set Screw
Can be placed on top or bottom.
8
Fixed Arm
. It
is recommended that before
mounting the hinge bracket, be
sure the locking pin is in place, and
the knurled set screw is tightened.
6
The hinge bracket can be mounted to
a fixed arm using a 3/8 in. Allen wrench
to tighten the four 1/2 - 13 x 2.00 in.
screws and hardware. Torque hardware to 75±2 ft. lbs. (102±3 N⋅M).
4
3
2
8
7
1
4
3
2
275 595-A
OM-274912 Page 4
8.
Locking Pin And Knurled Set Screw Hole Locations
1
!
Turn Off power for boom and column and all other electrical
equipment before working on
unit.
1
Mounting Hinge Bracket
2
Locking Pin Hole
2
Used to mount bracket at 90°.
6
3
Welding Equipment Mounting
Plate
4
Locking Pin
5
Locking Pin Hole
Used to mount bracket at 180°.
6
Knurled Set Screw
The hinge bracket can be mounted in
two different orientations. The hinge
bracket can be mounted so that the
mounting plate swings left hand from
180° to 90°, or flipped upside down to
swing right hand from 180° to 90°.
5
3
4
The locking pin and knurled set screw
can be placed on the top or bottom of
the hinge regardless of the orientation
of the hinge.
180° Position View
1
2
3
6
4
5
90° Position View
275 596-A
OM-274912 Page 5
9.
Changing Orientation Of Hinge From 1805 to 905
!
Turn Off power for boom and
column and all other electrical
equipment before working on
unit.
1
Mounting Hinge Bracket
2
Locking Pin
Step One
1
3
Hole − Locking Pin
4
Welding Equipment Mounting
Plate
5
Knurled Set Screw
Step One − Unlock the hinge bracket
by pressing the button on the locking
pin, and pulling pin out of the hole.
Step two − Turn knurled set screw
counterclockwise to loosen.
Step Three − Position equipment
mounting plate 90° to the mounting
hinge bracket. Turn knurled set screw
clockwise until tight.
5
2
Step Four − Lock hinge bracket in position by inserting locking pin into the
same hole from which it was removed.
3
Step Two
1
4
1
5
Step Three
4
Step Four
1
3
2
275 628-A
OM-274912 Page 6
10. Changing Orientation Of Hinge From 905 to 1805
Step One
!
Turn Off power for boom and
column and all other electrical
equipment before working on
unit.
1
Mounting Hinge Bracket
2
Locking Pin
1
3
Hole − Locking Pin
4
Welding Equipment Mounting
Plate
5
Knurled Set Screw
Step One − Unlock the hinge bracket
by pressing the button on the locking
pin, and pulling pin out of the hole.
Step two − Turn knurled set screw
counterclockwise to loosen.
3
Step Three − Position equipment
mounting plate parallel to the mounting
hinge bracket. Turn knurled set screw
clockwise until tight.
2
Step Four − Lock hinge bracket in position by inserting locking pin into the
same hole from which it was removed.
Step Two
5
1
4
Step Three
Step Four
3
1
1
4
5
2
275 597-A
OM-274912 Page 7
11. Replacement Parts List
Part No.
Description
Quantity
Item
No.
1 . . . . . . . . . . . . . . . . . . 275435 . . . . . . Pin, Quick Release T-Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 . . . . . . . . . . . . . . . . . . 275438 . . . . . . Knob, Cast Iron Knurled Rim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Use only Manufacturer’s Suggested Replacement Parts. Model number required when ordering parts.
Notes
OM-274912 Page 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising