Uniden | EXI4046 | Owner Manual | Uniden EXI4046 Owner Manual

Uniden EXI4046 Owner Manual
EXI 4046
EXI4046
Step 3 Set up the Base
Step 1 Check the Package Contents
Plug the AC adapter cord to
the DC IN 9V jack (yellow).
Make sure your cordless phone's
packaging includes the following items.
Step 5 Connect to the Phone Line
Plug one end of the
telephone cord into
the base TEL LINE
jack.
Route the cord.
Handset
AC adapter
Plug the other end into the
telephone wall jack.
Belt Clip
Rechargeable
Telephone
battery
cord
Also included: • Owner's manual
Step 6 Make & Receive Calls
Step 2 Install Handset Battery Pack and Charge
Note
Use ONLY the Uniden rechargeable battery pack supplied with
your new phone!
Remove the
cover.
Connect the
battery pack
with the correct polarity.
Replace the
cover.
Plug the AC adapter to a
120V AC power outlet.
Note
Use ONLY the Uniden AC adapter
supplied with your new phone!
Step 4 Charge the Handset
Place the handset in
the base.
Make sure that
charge LED
illuminates.
6QVCN
Charge the handset 15-20 hours.
Fully charge the battery pack by placing the
handset in the base before using phone.
www.uniden.com
To Make a Call
Press
talk/flash .
Listen for dial
tone.
Dial the desired
number.
To Receive a Call
Pick up the handset
and press talk/flash .
Handset/Base Set up:
- Adjust the Earpiece
Volume → P.19
- Set the Ringer Volume → P.17
- Set Tone/Pulse Dialing → P.16
Caller ID:
Set Caller ID on Call Waiting
(CIDCW) → P.14
Note: You must subscribe to Caller
ID services through your local
telephone provider to use Caller
ID and CIDCW.
Refer to your Owner's Manual
for detailed operations.
To Hang Up a Call
Press end or return
the handset to the
base.
For answers to questions and to
order genuine Uniden parts and
accessories 24 hours a day visit our
website at www.uniden.com. If you
have any problems, you can also call
our Customer Hotline at 1-800-2971023, Mon-Fri 7 a.m. to 7 p.m., Sat/
Sun 9 a.m. to 5 p.m. CST. (Phone
support is closed on holidays.)
QUICK REFERENCE GUIDE [1]
QUICK REFERENCE GUIDE
Base
Additional Features
For more information on these and
other features, please refer to your
Owner's Manual. For your
convenience, listed below are
important features that will help
you set up your new cordless phone.
EXI4046
3° Paso Preparación de la base
5° Paso Conexión de la línea telefónica
1° Paso Inspección del contenido del embalaje
Asegúrese de que haya recibido los siguientes
artículos en el paquete
Conecte el adaptador CA en el
enchufe (amarillo) DC IN 9V.
Pase el cable
Base
Receptor
Adaptador
CA
Pinza para
Pila
Cable
la correa
recargable
telefónico
Además va incluido: • Manual del usuario
Al enchufe telefónico
Al enchufe TEL LINE
Cable de la línea telefónica
(suministrado)
A la toma CA
Al enchufe DC IN 9V
Adaptador CA
(suministrado)
2° Paso Instalación y carga de la pila para el receptor
Nota ¡Use SOLAMENTE el paquete de
pilas recargable de Uniden suministrado con su nuevo teléfono!
Quite la tapa.
Conecte el
paquete de
pilas con la
polaridad
correcta.
Reponga la
tapa
Conecte un
extremo de la
línea telefónica
en el enchufe
TEL LINE en la
base.
Conecte el adaptador CA en
una toma de 120V CA.
Nota ¡Use SOLAMENTE el adaptador CA de
Uniden suministrado con su teléfono!
4° Paso Carga del receptor
Coloque el receptor
en la base.
Asegúrese de que el
LED de carga se
ilumine.
6QVCN
Cargue el receptor de 15 á 20 horas.
Cargue el paquete de pilas totalmente colocando
el receptor en la base antes de usar el teléfono.
[2] QUICK REFERENCE GUIDE
Conecte el otro extremo en el
enchufe telefónico de la pared.
6° Paso Realización y recepción de llamadas
Para hacer una llamada
Oprima
talk/flash .
Espere por el tono
de marcación.
Marque el
número deseado.
Para recibir una llamada
Levante el receptor y
oprima talk/flash .
Características adicionales
Para más información sobre estas y otras
características, le rogamos que consulte
su Manual del usuario. Para su
conveniencia, hemos listado abajo unas
características importantes, las cuales le
ayudarán a programar su nuevo teléfono
inalámbrico de Uniden.
Programación del receptor/base:
- Ajuste del volumen del auricular
y del altavoz → P.19
- Programación del volumen del
timbre → P.17
- Programación de la marcación
por tono/pulso → P.16
Identificación de llamadas (Caller ID):
Programe la Identificación de llamadas
en Llamadas en espera (CIDCW) → P.14
Nota: Usted debe estar suscrito al
servicio de Identificación de llamadas con su proveedor de telefonía
local para poder usar las características de Caller ID y de CIDCW
Consulte su manual del usuario para
operaciones más detalladas.
Para colgar una llamada
Oprima end o
devuelva el receptor
a la base.
Para hacer preguntas u ordenar partes genuinas y accesorios de Uniden, llame a nuestra
línea para atención al cliente en el 1-800297-1023.
Horario:
Lunes - viernes: 7 de la mañana- 7 de la
tarde. Sábado/domingo: 9 de la mañana - 5
de la tarde. No habrá ayuda telefónica los
días festivos. O, visite nuestra página Web:
http://www.uniden.com
www.uniden.com
Contents
QUICK REFERENCE GUIDE
Welcome/Features
Controls and Functions
Terms Used in this Manual
Accessibility
Installing the Phone
A. Choose the Best Location
B. Install the Rechargeable Battery Pack into the Handset
C. Connect the Base Unit and Charge the Handset
D. Mount the Base Unit on a Wall
Installing the Beltclip
Headset Installation
Basic Setup
Activating AutoTalk
Activating Caller ID on Call Waiting
Entering Your Area Code
Choosing the Dialing Mode
Setting the Language
Selecting the Ring Tone and Volume
Using Your Phone
Making and Receiving Calls
Redialing the Last Dialed Number
Adjusting the Earpiece Volume
Tone Dialing Switch-over
Traveling Out-of-Range
Selecting a Different Channel
Find Handset
www.uniden.com
1
4
5
6
7
8
8
9
10
11
12
13
14
14
14
15
16
16
17
18
18
19
19
20
20
20
21
Using Call Waiting
Voice Mail Waiting Indicator
Using the Speed Dial Memory
Storing Names and Numbers in Speed Dial Memory
Storing Caller ID Messages in Speed Dial Memory
Making Calls from Speed Dial Memory
Caller ID and CIDCW (Caller ID on Call
Waiting)
Viewing the Caller ID Message List
Deleting Information from the Caller ID List
Making a Call from the Caller ID List
Caller ID on Call Waiting (CIDCW)
Changing the Digital Security Code
Note on Power Sources
General Information
Troubleshooting
Liquid Damage
Precautions & Warranty
I.C. Notice
Index
Memory List
21
22
23
23
26
27
28
29
30
31
31
32
33
35
36
38
39
41
42
43
[3]
Welcome
Congratulations on your purchase of the Uniden cordless telephone. This phone is designed and
engineered to exacting standards for reliability, long life, and outstanding performance.
Note: Illustrations in this manual are used for explanation purposes. Some
illustrations in this manual may differ from the actual unit. The color of your
cordless phone may vary.
As an Energy Star Partner, Uniden has determined that this product or product
models meets the Energy Star guidelines for energy efficiency.
Energy Star is a U.S. registered mark.
Features
•
•
•
•
•
•
•
2.4GHz Extended Range Technology
Caller ID/Caller ID on Call Waiting
3-Line Backlit LCD
Trilingual Menu Displays
30 Caller ID Memory
10 Number Memory Dialing
Last Number Redial
•
•
•
•
•
•
•
Tone/Pulse Dialing
Find Handset Key
Earpiece/Ringer Volume Controls
Mute or Turn Ringer Off
Hearing Aid Compatible
20 Channel Auto Scan
Desk or Wall Mountable
If you have any trouble with your phone, call our Customer Hotline at 1-800-297-1023,
Mon-Fri 7 am to 7 pm, Sat/Sun 9 am to 5 pm, CST. (Phone support is closed on holidays.)
For more information on Uniden products and accessories, be sure to visit our web site:
www.uniden.com
Uniden® is a registered trademark of Uniden America Corporation.
AutoTalk, AutoStandby, UltraClear Plus, Random Code, and AutoSecure are trademarks of
Uniden America Corporation.
[4]
www.uniden.com
Controls and Functions
1
2
6
3
4
7
8
9
5
13
14
15
10
11
16
17
12
18
19
www.uniden.com
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Handset antenna
Jack for optional headset
Beltclip hole
Ringer speaker
Handset battery compartment
Handset earpiece
LCD display
/ /vol/
(earpiece volume, ringer
volume and scroll) key (pages 14, 17 and
19)
Call id/menu key (pages 14 and 28)
/tone/
key (left cursor) key
(pages 20 and 23)
Redial/pause key (pages 19 and 25)
Select key (page 14)
Talk/flash key (pages 18 and 21)
End key (pages 18 and 19)
Memory key (page 23)
#/
(right cursor) key (page 23)
Delete/chan key (pages 20, 23 and 30)
Handset microphone
Handset charging contacts
*
CONTROLS & FUNCTIONS [ 5 ]
CONTROLS & FUNCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
20. Base charging contacts
21. Find hs key (pages 21 and 32)
22. Charge/in use and VMWI
(Voice Mail Waiting Indicator) LED
23. DC IN 9V jack
24. Telephone line jack
20
21
22
23
24
Terms Used in this Manual
[6] TERMS USED IN THIS MANUAL
www.uniden.com
TERMS USED IN THIS
MANUAL
• Standby Mode - The handset may be sitting in or off the base, but is NOT in use. The talk/flash key has not
been pressed and there is no dial tone.
• Talk Mode - The handset is off the base and the talk/flash key has been pressed, enabling a dial tone.
• CID - Caller ID
• CIDCW - Caller ID on Call Waiting
Accessibility
Uniden provides a customer service hotline for accessibility questions. If you have a disability and need customer
service assistance or if you have any questions about how Uniden's products accommodate persons with disabilities,
please call the accessibility voice/TTY line:
1-800-874-9314
A representative is available to talk to you M-F, 8:00 am to 5:00 pm, CST. After hours, you can leave a message, and
we will call you back. Information is also available on our web site, www.uniden.com, under the "Accessibility" link.
ACCESSIBILITY [ 7]
ACCESSIBILITY
www.uniden.com
INS TA LLI NG TH E
PHONE
Installing the Phone
note
If your home has
specially wired alarm
equipment connected to
the telephone line, be
sure that installing the
system does not disable
your alarm equipment.
If you have questions
about what will disable
your alarm equipment,
contact your telephone
company or a qualified
installer.
Do the following steps:
A.
B.
C.
D.
Choose the Best Location
Install the Rechargeable Battery Pack into the Handset
Connect the Base Unit and Charge the Handset
Mount the Base Unit on a Wall
A. Choose the Best Location
When choosing a location for your new phone, here are some important guidelines you should consider:
Avoid heat sources, such as radiators,
air ducts, and sunlight
Avoid television sets and other
electronic equipment
Avoid noise sources such as a window by
a street with heavy traffic
Avoid microwave ovens
Avoid excessive moisture,
extremely low temperatures, dust,
mechanical vibration, or shock
Choose a central location
Avoid personal computers
Avoid other cordless telephones
• The location should be close to both a phone jack and a continuous power outlet (one
which is not connected to a switch).
• The base and handset should be kept away from sources of electrical noise such as motors,
microwave ovens, and fluorescent lighting.
• The base can be placed on a desk, tabletop, or mounted on a standard wall plate. For
better reception, place the base as high as possible.
• The base should be placed in an open area for optimum range and reception.
[8] INSTALLING THE PHONE
www.uniden.com
The handset is powered by a rechargeable battery pack.
The battery recharges automatically when the handset is placed
in the base unit.
1) Press down on the handset battery case cover (use the
finger indention for a better grip) and slide the cover
downward to remove.
2) Plug the battery pack connector (red & black wires) into the
jack inside the battery compartment.
(The connector notches fit into the grooves of the jack only
one way.) Match the wire colors to the polarity label in the
battery compartment, connect the battery and listen for a
click to insure connection.
!
Use only the Uniden
(BT-905) rechargeable
battery pack supplied
with your cordless
telephone.
3) Make sure you have a good connection by slightly pulling on
the battery wires. If the connection is secure, the battery
jack will remain in place.
4) Place the battery case cover back in the handset by sliding
it upwards until it clicks into place.
www.uniden.com
INSTALLING THE PHONE [9]
INS TA LLI NG TH E
PHONE
B. Install the Rechargeable Battery Pack into the Handset
!
•Use only the supplied
AD-0001 AC adapter.
Do not use any other
AC adapter.
•Do not place the power
cord where it creates a
trip hazard or where it
could become chafed
and create a fire or
electrical hazard.
1) Connect the AC adapter to the DC IN 9V jack and to
a standard 120V AC wall outlet.
Route the cord.
2) Place the handset in the base unit with the keypad
facing forward.
3) Make sure the charge/in use LED illuminates.
If the LED does not illuminate, check to see that the AC
adapter is plugged in and the handset makes good
contact with the base charging contacts.
• Connect the AC adapter to a continuous power
supply.
• Place the base unit close to the AC outlet to
avoid long extension cords.
4) Charge your handset at least 15-20 hours before
plugging the phone line.
5) Once the handset battery pack is fully charged,
connect the telephone line cord to the TEL
LINE jack and a telephone outlet.
If your telephone outlet isn't modular, contact
Modular
your telephone company for assistance.
[10] INSTALLING THE PHONE
www.uniden.com
INS TA LLI NG TH E
PHONE
C. Connect the Base Unit and Charge the Handset
INS TA LLI NG TH E
PHONE
D. Mount the Base Unit on a Wall
Standard wall plate mounting
This phone can be mounted on any
standard wall plate.
1) Plug the AC adapter to the DC IN 9V
jack.
2) Plug the AC adapter into a standard
120V AC wall outlet.
3) Plug the telephone line cord into the
TEL LINE jack.
4) Plug the telephone line cord into the
telephone outlet.
5) Align the mounting slots on the base
with the mounting posts on the wall.
Then push in and down until the
phone is firmly seated.
1
3
5
4
5
2
www.uniden.com
INSTALLING THE PHONE [11]
If you don't have a standard wall plate, you can mount your phone
directly to the wall. Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting
location that could cause a hazard when inserting screws into the
wall.
• Try to mount your phone within 5 feet of a working phone jack to
avoid excessive cord lengths.
• Make sure the wall material is capable of supporting the weight of
the base and handset.
• Use #10 screws (minimum length of 1-3/8 inches) with anchoring
devices suitable for the wall material where the base unit will be
placed.
1) Insert two mounting screws into the wall, (with their appropriate anchoring device), 315/16 inches apart. Allow about 1/8 of an inch between the wall and screw heads for
mounting the phone.
2) Refer to steps 1 through 5 on page 11 to mount the telephone.
Installing the Beltclip
To attach the beltclip
Insert the beltclip into the holes on each side of the handset. Press down until it clicks.
To remove the beltclip
Pull both sides of the beltclip to release the tabs from the holes.
[12] INSTALLING THE PHONE
www.uniden.com
INS TA LLI NG TH E
PHONE
Direct wall mounting
INS TA LLI NG TH E
PHONE
Headset Installation
Your phone may be used with an optional headset. To use this feature,
insert the headset plug into the headset jack.
Your phone is ready for hands-free conversations.
(Headsets may be purchased by visiting our website at www.uniden.com or
by calling our Parts Department. See back cover page.)
www.uniden.com
INSTALLING THE PHONE [13]
Basic Setup
There are five basic options that you will need to set up: AutoTalk, CIDCW (Caller ID on Call
Waiting), Area Code, Dial Mode and Language.
Activating AutoTalk
AutoTalk allows you to answer the phone simply by removing the handset from the base. You
do not have to press any keys.
Activating Caller ID on Call Waiting
Caller ID allows you to see the name and number of the calling party before you answer the
phone. Caller ID on Call Waiting (CIDCW) lets you see the name and number of a call that
comes in when you are on the line.
You must subscribe to Caller ID service through your local telephone provider to use this
feature.
1) When the phone is in standby mode, press and hold the call id/
menu key. The following screen appears.
[14] BASIC SETUP
www.uniden.com
BASIC SETUP
1) When the phone is in standby mode, press and hold the call id/
menu key. The following screen appears.
2) Press the select key to turn AutoTalk on.
3) Press the end key to complete the setting. The handset returns to standby mode.
2) Press the
/vol/
key to select
C IDC W.
3) Press the select key to toggle and turn on Caller ID on Call Waiting.
4) Press the end key and return the handset to the base unit to complete the setting. The
handset returns to standby mode.
Entering Your Area Code
1) When the phone is in standby mode, press and hold the call id/
menu key. The following screen appears.
2) Press the
/vol/
key twice to select
Ar ea Cod e .
3) Press the select key. If an area code was already stored, the
phone will display it.
4) Use the number keys (0 - 9) to enter the 3-digit area code. If you
make an error, use the delete/chan key to backspace.
5) Press the select key. A confirmation tone sounds.
6) Press the end key to complete the setting. The handset returns to standby mode.
www.uniden.com
BASIC SETUP [15]
BASIC SETUP
If you can make a call by dialing only 7 digits (instead of 10), you can program your local area
code in your phone. If you get a call from within your area code, you'll only see the 7-digit
phone number. If you get a call from outside your area code, you'll see all 10 digits.
Choosing the Dialing Mode
note
1) When the phone is in standby mode, press and hold the call id/
menu key. The following screen appears.
2) Press the
/vol/
key three times to select
BASIC SETUP
If your phone system
requires pulse dialing
and you need to send
DTMF tones during a
call, you can
temporarily switch over
to tone dialing. (Refer
to “Tone Dialing Switchover” on page 20.)
Your phone can communicate with the telephone network in two different ways: tone dialing
and pulse dialing. These days, most phone networks use a method called tone dialing, so
your phone comes programmed for tone dialing.
If your phone company uses pulse dialing, you'll need to change your phone's dial mode.
There's an easy way to tell: try making a call. If your call connects, your phone's setting is
fine. If not, follow the steps below:
D ial .
3) Press the select key to set the phone to pulse dialing.
4) Press the end key to complete the setting. The handset returns to
standby mode.
Setting the Language
You can change the language the menu display uses. Choose from English, French, or
Spanish.
1) When the phone is in standby mode, press and hold the call id/
menu key. The following screen appears.
2) Press the
[16] BASIC SETUP
/vol/
key four times to select
Lan gua ge .
www.uniden.com
3) Press the select key to select
En g , F r.
or
Esp .
4) Press the end key to complete the setting. The handset returns to
standby mode.
Selecting the Ring Tone and Volume
Your phone has five different ringer tone/volume combinations you can choose from.
1) With the phone in standby mode, press the
/vol/
or
/vol/
key.
3) When the phone sounds the ring tone and volume you wish to use, press the end key.
www.uniden.com
BASIC SETUP [17]
BASIC SETUP
2) The phone will sound the different ring tones at different volumes. To turn the ringer off,
select R ing er Off .
Using Your Phone
note
Making and Receiving Calls
Making a call
1) Remove the handset from the base.
2) Press the talk/flash key.
3) Listen for the dial tone.
4) Dial the number.
OR
1) Remove the handset from the base.
2) Dial the number.
3) Press the talk/flash key.
Receiving a call
To turn on the AutoTalk
feature, see “Activating
AutoTalk” on page 14.
*
key
Hanging up
Press the end key or return the handset to the base.
[18] USING YOUR PHONE
www.uniden.com
USING YOUR
PHONE
1) Remove the handset from the base. (If AutoTalk is on, the phone will automatically
answer the call when you pick it up.)
2) Press the talk/flash key.
OR
key, the #/
1) If the handset is off the base, press the talk/flash key, the /tone/
or any number key. (AutoTalk is on.)
Redialing the Last Dialed Number
1) Remove the handset from the base.
2) Press the talk/flash key.
3) Listen for the dial tone.
4) Press the redial/pause key.
OR
1) Remove the handset from the base.
2) Press the redial/pause key.
3) Press the talk/flash key.
note
Adjusting the Earpiece Volume
To change the earpiece volume, press the
/vol/
key during a call.
/vol/
or
Temporarily Mute Ringer
If the handset is off the base while an incoming call is
ringing, simply press the end key to mute the incoming
ring. The ringer will sound with the next incoming call.
You can only mute the
handset ringer if the
handset is off the base
when the phone starts
ringing
USING YOUR
PHONE
www.uniden.com
USING YOUR PHONE [19]
Tone Dialing Switch-over
note
If your telephone company requires pulse dialing, you can
switch over to tone dialing after the call connects. This
feature is useful when you need tone dialing to use any
automated menu systems, such as telephone bank tellers,
telephone prescription refills, customer support menus, etc.
If your phone is set to pulse dialing mode, make your call
normally. Once your call connects, press the /tone/
key. Any digits you enter from then on will be sent as tone
digits. When this particular call ends, the phone
automatically returns to pulse dialing mode.
*
Traveling Out-of-Range
During a call, as you begin to move your handset too far from your base unit, noise
increases. If you pass the range limits of the base, your call will terminate within one
minute.
Selecting a Different Channel
If you encounter interference while using your phone, you can manually change the phone´s
channel for clear operation. While using your phone, press the delete/chan key. Scanning
appears on the display, indicating the phone is changing to another channel. For more
information on interference, refer to "Radio Interference" on page 40.
[20] USING YOUR PHONE
www.uniden.com
USING YOUR
PHONE
The UltraClear PlusTM
true compander circuitry
virtually eliminates
background noise. This
innovative technology,
together with 20
different channels,
provides you with the
best possible reception
during all your
conversations.
Find Handset
To locate the handset, press the find hs key on the base. The
handset beeps for 60 seconds.
To cancel paging, press any key on the handset or the find hs
key on the base, or return the handset to the base.
Paging is also canceled when the phone receives an incoming
call.
Using Call Waiting
If you have Call Waiting, you can receive calls while on the
line.
You must subscribe to Call Waiting through your local telephone company.
www.uniden.com
USING YOUR PHONE [21]
USING YOUR
PHONE
1) If a call comes in while you are on the phone, you will
hear a call waiting tone. If you have CIDCW activated,
you will see the name and number of the incoming caller.
2) Press the talk/flash key to accept the waiting call. After
a short pause, you will hear the new caller.
3) To return to the original caller, press the talk/flash key
again.
Voice Mail Waiting Indicator
note
If you subscribe to voice mail service, you can use your cordless telephone to access your
voice mailbox. The charge/in use LED on the base of your phone flashes whenever you have
messages waiting in your voice mailbox.
You must subscribe to
voice mail service from
your telephone company
in order to use this feature. The voice mail
company will provide
you with the access
number.
Just dial the access number supplied by your voice mail provider to enter your mailbox.
You can program your voice mail access number to a speed dial number.
If the voice mail waiting indicator remains on after you have retrieved your messages, press
and hold the find hs key for 5 seconds. This will reset the indicator.
USING YOUR
PHONE
[22] USING YOUR PHONE
www.uniden.com
The speed dial memory allows you to store up to 10 names and numbers in the handset. You
can dial these numbers with just a few key presses.
The speed dial memory is not limited to phone numbers. You can store any number (up to 20
digits) that you need to enter once your call connects. This is referred to as Chain Dialing.
For example, you can save your bank account number to speed dial memory. When you call
your bank's telephone teller service and are prompted to enter your account number, simply
press the memory key and the speed dial number where you stored your account number.
Then press the select key.
Storing Names and Numbers in Speed Dial Memory
note
When editing the speed
dial memory, you must
press a key within 30
seconds or the phone
will return to standby
mode. If you return the
handset to the base, the
phone will return to
standby mode also.
1) With the phone in standby mode, press the memory key.
2) Enter 0-9 to select the speed dial number where you would like to
store this entry. You can also scroll through the list with the
/
vol/ and
/vol/
keys. Press the select key twice.
3) Store Name appears and a cursor flashes indicating that the
phone is ready for the name to be entered.
If the selected speed dial number is already assigned, the Edit
screen appears. You can select Edit to edit this entry, select
Delete to erase this entry, delete this entry, or select Go Back to
choose another speed dial number.
www.uniden.com
USING THE SPEED DIAL MEMORY [23]
USING THE SPEED
DIAL MEMORY
Using the Speed Dial Memory
If the next character
uses the same number
key, you must press the
#/
key to move the
cursor over. Otherwise
the next time you press
the number key, it
changes the character
that was previously set.
*
Refer to the letters on the number keys to select the desired characters.
With each press of a numeric key, the displayed character appears in the following order:
upper case letters first, lower case letters next and finally the number corresponding to
the key.
If you make a mistake while entering a name
Use the /tone/
or #/
key to move the cursor to the incorrect character.
Press the delete/chan key to erase the wrong character. Then enter the correct character.
To delete all characters, press and hold the delete/chan key.
*
For example, to enter Movies.
1) Press 6. Then press the #/
key to
move the cursor to the right.
2) Press 6 six times.
3) Press 8 six times.
4) Press 4 six times.
5) Press 3 five times.
6) Press 7 eight times.
Number of times key is pressed
keys
1
2
3
4
5
6
7
8
9
1
2abc
3def
4ghi
5jkl
6mno
7pqrs
8tuv
9wxyz
0 oper
[24] USING THE SPEED DIAL MEMORY
www.uniden.com
USING THE SPEED
DIAL MEMORY
note
4) Enter a name according to the instructions below, then press the select key. If no name is
required, go to step 5.
• The name can be up to 13 characters.
• Use the #/
and /tone/
keys to move the cursor to the desired location.
• Use the delete/chan key to delete characters as needed.
• Press and hold the delete/chan key to delete all the characters.
6) Use the keypad to enter the phone number; each number can be
up to 20 digits.
If you need the phone to pause during the dialing sequence, press
the redial/pause key to insert a two-second delay between the
numbers. You can enter multiple pauses to increase the delay.
Each pause counts as a digit. The display shows a P for every
pause.
When storing numbers into memory, if the handset is idle (i.e., no key is pressed) for more
than 30 seconds, it will beep rapidly, and the phone will return to standby mode.
7) Press the memory key. You will hear a confirmation tone, and the
following screen appears.
Memory storage is complete.
After about 2 seconds, the following screen displays all the speed
dial memory entries.
8) Press the end key to exit memory setup mode. The phone returns
to standby.
www.uniden.com
USING THE SPEED DIAL MEMORY [25]
USING THE SPEED
DIAL MEMORY
5) Store Number is displayed. The cursor flashes indicating that the
phone is ready for the number to be entered.
note
You cannot store a
Caller ID message if no
phone number appears
in the message.
Messages (Caller ID names/numbers) shown in the Caller ID list can be stored in memory
dialing. For instructions on viewing the Caller ID Message list, see page 29.
1) Press the call id/menu key. Select the phone number to be stored
from the Caller ID list by pressing the
/vol/ or /vol/
key.
2) Press the memory key.
3) Enter a number (0 - 9) or press the
location to be stored.
/vol/
or
/vol/
key to select the memory
4) Press the select key. You hear a confirmation tone, and the
number is stored in memory. The display returns to the Caller ID
list.
If a number has already been stored in the selected memory
number location, a confirmation screen is displayed.
Press the
/vol/
key to select Yes. Press the select key to
overwrite. The display returns to the Caller ID list.
[26] USING THE SPEED DIAL MEMORY
www.uniden.com
USING THE SPEED
DIAL MEMORY
Storing Caller ID Messages in Speed Dial Memory
1) Press the memory key. The handset displays your programmed
speed dial number.
2) Enter the number (0 - 9), or press the /vol/ or
/vol/
key to select the speed dial number you would like to dial.
3) Press the talk/flash key. Talk and the number selected appear on
the display. Then the displayed number is dialed.
To cancel speed dialing
Press the end key to cancel speed dialing. The handset returns to standby mode.
Also, if the handset is idle (e.g., no key is pressed) for 30 seconds, the phone returns to
standby mode.
www.uniden.com
USING THE SPEED DIAL MEMORY [27]
USING THE SPEED
DIAL MEMORY
Making Calls from Speed Dial Memory
Caller ID and CIDCW (Caller ID on Call Waiting)
note
•When the call is
received via a
telephone company
that does not offer
Caller ID service, the
caller´s phone number
and name do not
appear. (This includes
international calls.)
The date and
time received
Caller's name
Caller's phone number
CALLER ID AND CIDCW
(CALLER ID ON CALL WAITING)
•If you answer a call
before the Caller ID
message is received
(for example, before
the second ring), the
Caller ID message will
not appear.
You must subscribe to Caller ID service through your local telephone provider to use
this feature. When the telephone rings, the Caller ID feature allows you to view the caller’s
name, phone number, date and time of call. The incoming call information is stored in the
Caller ID record. If the Caller ID service includes the caller´s name, the caller´s name appears
on the display (up to 15 letters).
You may receive any one of the following messages:
When invalid data is received
Incomplete Data
When a private name is received
Private Name
When a private number is received Private Number
When a unknown name is received
Unknown Name
When a unknown number is received Unknown Number
Data errors appear as ¨ ¨.
•When the call is
received via a private
branch exchange
(PBX), the caller´s
phone number and
name may not appear.
[28] CALLER ID AND CIDCW (CALLER ID ON CALL WAITING)
www.uniden.com
Viewing the Caller ID Message List
The Caller ID list stores information for up to 30 incoming calls - even unanswered calls. You
can also view the Caller ID list during a call.
1) Press the call id/menu key. The summary screen displays the
number of new messages and total messages.
3) Press the call id/menu key to return to talk mode, or press the end key to return to
standby mode.
•In Caller ID operation,
if no key is pressed for
more than 30 seconds,
an error tone sounds
and the telephone
returns to standby
mode.
•Each message can be
up to 15 characters for
the name and 15 digits
for the phone number.
•The number of calls
from the same Caller ID
appears next to the
received time. Once
you view the new
message, the number
will be cleared and
disappear.
•During a call, don't
press the end key, or
the call will be
disconnected.
www.uniden.com
CALLER ID AND CIDCW (CALLER ID ON CALL WAITING) [29]
CALLER ID AND CIDCW
(CALLER ID ON CALL WAITING)
2) Use the /vol/
key to scroll through the messages from the
latest to the earliest, or use the /vol/ key to scroll through
the messages from the earliest to the latest.
note
Deleting Information from the Caller ID List
note
If the phone receives more Caller ID messages than it can store, the oldest one in the list is
automatically deleted. Caller ID data can also be deleted manually.
Deleting a Caller ID message
•If you get an incoming
call or page, the
deleting operation is
canceled, and you can
answer the call or
page.
1) Press the call id/menu key in standby mode. Find the message to
be deleted from the Caller ID list by pressing the
/vol/
or
/vol/ key.
CALLER ID AND CIDCW
(CALLER ID ON CALL WAITING)
•While using the Delete
All? or Delete
Message? screen, if no
key is pressed for more
than 30 seconds, an
error tone sounds, and
the handset returns to
standby mode.
2) Press the delete/chan key.
3) Press the
/vol/
or
press the select key.
/vol/
key to select
Yes,
and then
Deleting all Caller ID names/numbers
1) With the phone in standby mode, press the call id/menu key.
2) Press the delete/chan key.
3) Press the
/vol/
or /vol/ key to select Yes, and then
press the select key.
You hear a confirmation tone and all stored Caller ID messages are
deleted.
[30] CALLER ID AND CIDCW (CALLER ID ON CALL WAITING)
www.uniden.com
Making a Call from the Caller ID List
You can place a call from the Caller ID list.
1) Press the call id/menu key in standby mode. Select the phone
number that you want to dial by pressing the /vol/
or
/
vol/ key.
2) To have the phone dial a 1 before the displayed Caller ID number, press 1. To have the
phone dial the stored area code before the displayed Caller ID number, press 3.
note
3) Press the talk/flash key. The displayed phone number dials automatically.
Caller ID on Call Waiting (CIDCW)
With CIDCW, you will hear a Call Waiting tone while you are on a call, and the Caller ID data
is displayed. To accept the waiting call, press the talk/flash key (see page 21).
www.uniden.com
CALLER ID AND CIDCW (CALLER ID ON CALL WAITING) [31]
CALLER ID AND CIDCW
(CALLER ID ON CALL WAITING)
You cannot make a call
from the Caller ID list if
your cordless phone is
connected to a private
branch exchange (PBX).
Changing the Digital Security Code
To protect you against misbilled calls which might result from your phone being activated by
other equipment, the cordless phone provides AutoSecureTM (which electrically locks your phone
when the handset is in the base) and Random CodeTM digital security which automatically selects
one of over 262,000 digital security codes for the handset and base.
If the handset battery pack is completely discharged or the battery pack is removed, the digital
security code will be lost. If this happens, a new security code is set automatically the next time
the battery pack is charged. In the rare situation that you suspect another cordless telephone
is using the same security code, you can change the code.
1) Remove the handset from the base unit. Press and hold the find hs key on the base.
2) While holding the find hs key, place the handset in the base unit, and leave the handset
in the base for more than 3 seconds. A new random security code is set.
www.uniden.com
CH AN G I N G T H E D I GI TAL
SECURITY CODE
[32] CHANGING THE DIGITAL SECURITY CODE
Note on Power Sources
Low battery alert
When the battery pack is very low and needs to be charged, the phone is
programmed to eliminate functions in order to save power. If the phone is not in
use, L ow Bat ter y appears on the LCD and none of the keys will operate.
If the phone is in use, Lo w Bat ter y flashes and the handset beeps. Complete your
conversation as quickly as possible and return the handset to the base unit for
charging.
Information stored in the phone's memory will be retained for 30 minutes after
the battery pack is removed. This includes all setup information, last number dialed, speed dial memory, and the CID
list.
Even when the battery pack is not being used, it will gradually discharge over a long period of time. For optimum
performance, be sure to return the handset to the base unit after a telephone call.
Battery replacement and handling
Power Failure
During the period that the power is off, you will not
be able to make or receive calls with the telephone.
www.uniden.com
•
•
•
•
Caution
Use only the specified Uniden battery pack (BT-905).
Do not remove the battery from the handset to charge it.
Never throw the battery into a fire, disassemble it, or heat it.
Do not remove or damage the battery casing.
NOTE ON POWER SOURCES [33]
NOTE ON POWER
SOURCES
When the operating time becomes short even after a battery is recharged, please replace the battery.
With normal usage, your battery should last about one year. A replacement battery may be purchased by calling
Uniden’s Parts Department (see back cover page).
Warning: To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden
battery model and Uniden adapter model specifically designated for this product.
Cleaning the battery charging contacts
To maintain a good charge, clean the charging contacts on
the handset once a month.
Dampen a cloth with plain water. Gently rub the damp
cloth over the charging contacts until all visible dirt is
removed. Dry the contacts thoroughly before returning the
handset to the base.
Caution
Do not use paint thinner, benzene,
alcohol, or other chemical products.
Doing so may discolor the surface of
the telephone and damage the finish.
www.uniden.com
NOTE ON POWER
SOURCES
[34] NOTE ON POWER SOURCES
GENERAL
INFORMATION
General Information
The phone complies with FCC Parts 15 and 68.
Operating temperature: -10°C to +50°C (+14°F to +122°F)
AC Adapter Information
AC Adapter part number:
AD-0001
Input Voltage:
120V AC 60Hz
Output Voltage:
9V DC 210 mA
Battery Information
Battery part number:
BT-905
Capacity:
600 mAh, 3.6V
Frequency
924.516925 - 926.704425 MHz
2,405.155942 - 2,411.718441 MHz
• To avoid damage to the phone use only Uniden AD-0001 and BT905 with your phone.
• If the handset is left off the base, the actual talk mode duration will be reduced respective to the amount of time
the handset is off the base.
Recharge your phone on a regular basis by returning the handset to the base after each phone call.
When the operating time becomes short, even after the battery is recharged, please replace the battery.
With normal usage, the battery should last about one year.
A replacement Uniden adapter or battery may be purchased by calling Uniden’s Parts Department (see back cover
page).
Specifications, features, and availability of optional accessories are all subject to change without prior notice.
www.uniden.com
GENERAL INFORMATION [35]
Troubleshooting
If your phone is not performing to your expectations, please try these simple steps first. If these steps do not solve
your problem, please call our Customer Hotline at 1-800-297-1023. (Mon - Fri 7 am to 7 pm, Sat/Sun 9 am to 5 pm,
CST. Phone support is closed on holidays.)
Symptom
Suggestion
• Make sure the AC adapter is plugged into the base and wall outlet.
• Make sure the handset is properly seated in the base.
• Make sure the charging contacts on the handset are clean.
The audio sounds weak and/or
scratchy.
• Move the handset and/or base away from metal objects or appliances and try again.
• Press the delete/chan key in the talk mode to help eliminate background noise.
• Make sure that the handset is not too far from the base.
Can't make or receive calls.
• Check both ends of the telephone line cord.
• Make sure the AC adapter is plugged into the base and wall outlet.
• Disconnect the AC adapter for a few minutes. Then reconnect it.
• Change the digital security code (see page 32).
• Make sure that the handset is not too far from the base.
• Check the dialing mode used by your telephone company.
[36] TROUBLESHOOTING
www.uniden.com
TROUBLESHOOTING
The charge/in use LED won't
illuminate when the handset is
placed in the base.
Symptom
Suggestion
• The battery pack may be weak. Charge the battery for 15-20 hours.
• The handset may be too far from the base unit.
• Place the base unit away from appliances or metal objects.
• Change the digital security code (see page 32).
• Check the battery pack to ensure there is a secure connection.
• Make sure ringer volume isn't set to "off."
Severe noise interference.
• Keep the handset away from microwave ovens, computers, remote control toys, wireless
microphones, alarm systems, intercoms, room monitors, fluorescent lights, and electrical
appliances.
• Move to another location or turn off the source of interference.
The Caller ID does not display.
• The call was answered before the second ring.
• The call was placed through a switchboard.
• Charge the handset.
• Your Caller ID service may not be active; contact your local telephone service provider.
Voice Message Indication does
not work.
• Contact your local telephone company to make sure that your telephone receives FSK message
signaling.
• Reset the indicator by pressing and holding the find hs key for 5 seconds.
www.uniden.com
TROUBLESHOOTING [37]
TROUBLESHOOTING
The handset doesn't ring or
receive a page.
Liquid Damage
Moisture and liquid can damage your cordless phone. In case of accidental submersion, please follow these steps.
Case
Action
If the handset or base is exposed to
Wipe off the liquid, and use as normal.
moisture or liquid, but it only affects the
exterior plastic housing.
[38] TROUBLESHOOTING
Handset:
1.Remove the battery cover and leave it off for ventilation
2.Remove the battery pack by disconnecting
3.Leave the battery cover off and the battery pack disconnected for at least 3 days
4.Once the handset is completely dry, reconnect the battery pack and the battery cover.
5.Recharge the handset’s battery pack for 20 hours before using again.
Base:
1.Disconnect the AC adapter from the base unit, cutting off electrical power.
2.Disconnect the telephone cord from the base unit.
3.Let dry for at least 3 days.
IMPORTANT: You must unplug the telephone line while recharging the battery pack to
avoid charge interruption.
CAUTION:
DO NOT use a microwave oven to speed up the drying process. This will cause permanent
damage to the handset, base and the microwave oven.
After following these steps, if your cordless telephone does not work, please call our
Customer Service Hotline at 1-800-297-1023.
www.uniden.com
TROUBLESHOOTING
If moisture or liquid has entered the
plastic housing (i.e., liquid can be heard
in the phone or liquid has entered the
handset battery compartment or vent
openings on the base).
Precautions!
Before you read anything else, please observe the following:
Warning!
Uniden America Corporation DOES NOT represent this unit to be
waterproof. To reduce the risk of fire, electrical shock, or damage
to the unit, DO NOT expose this unit to rain or moisture.
Uniden works to reduce lead content in our PVC coated cords in
our product and accessories.
Warning!
The cords on this products and/or accessories contain lead, a
chemical known to the State of California to cause birth defects or
other reproductive harm. Wash hands after handling.
Rechargeable Nickel-Cadmium Battery Warning
Important Safety Instructions
•This equipment contains a rechargeable nickel-cadmium battery.
•Cadmium is a chemical known to the State of California to cause
cancer.
•The rechargeable nickel-cadmium battery contained in this
equipment may explode if disposed of in a fire.
•Do not short-circuit the battery.
•Do not charge the rechargeable nickel-cadmium battery used in
this equipment in any charger other than the one designed to
charge this battery as specified in the owner’s manual.
Using another charger may damage the battery or cause the
battery to explode.
When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:
Rechargeable Nickel-Cadmium
Batteries Must Be Recycled or
Disposed of Properly
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
www.uniden.com
SAVE THESE INSTRUCTIONS
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions. Do not
open or mutilate the battery, and disconnect the battery before
shipping this product.
The FCC Wants You To Know
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the bottom of this
equipment is a label that contains, among other information, a
product identifier in the format US:AAAEQ##TXXXX. If requested,
this number must be provided to the telephone company.
An applicable Universal Service Order Codes (USOC) certification
for the jacks used in this equipment is provided (i.e., RJ11C) in
the packaging with each piece of approved terminal equipment.
A plug and jack used to connect this equipment to the premises
wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this
NOTICE: According to telephone company reports, AC electrical
surges, typically resulting from lightning strikes, are very
destructive to telephone equipment connected to AC power
sources. To minimize damage from these types of surges, a surge
arrestor is recommended.
Changes or modifications to this product not expressly approved
by Uniden, or operation of this product in any way other than as
detailed by the owner's manual, could void your authority to
operate this product.
PRECAUTIONS & WARRANTY [39]
PRECAUTIONS &
WA R R A N T Y
•Uniden voluntarily participates in an RBRC® industry program to
collect and recycle nickel-cadmium batteries at the end of their
useful life, when taken out of service within the United States.
The RBRC® program provides a convenient alternative to placing
used nickel-cadmium batteries into the trash or municipal waste
stream, which is illegal in some areas.
•Through the RBRC® program, Uniden makes it easy for you to
drop off the used battery at local retailers of replacement nickelcadmium batteries. You may also contact your local recycling
center for information on where to return the used battery.
Please call 1-800-8-BATTERY for information on Ni-Cd battery
recycling in your area. Uniden's involvement in this program is
part of its commitment to protecting our environment and
conserving natural resources.
•RBRC® is a registered trademark of the Rechargeable Battery
Recycling Corporation.
1. Do not use this product near water, for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement
or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock
from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of
the leak.
4. Use only the power cord and batteries indicated in this manual.
Do not dispose of batteries in a fire. They may explode. Check
with local codes for possible battery disposal instructions.
5. Do not disassemble any component of this product.
product. It is designed to be connected to a compatible modular
jack that is also compliant. See installation instructions for
details.
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line
may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed
five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the
local telephone company. For products approved after July 23,
2001, the REN for this product is part of the product identifier
that has the format US:AAAEQ##TXXXX. The digits represented by
## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice
isn’t practical, the telephone company will notify the customer as
soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities,
equipment, operations or procedures that could affect the
operation of the equipment. If this happens the telephone
company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
Please follow instructions for repairing, if any (e.g. battery
replacement section); otherwise do not substitute or repair any
parts of the device except as specified in this manual.
Connection to party line service is subject to state tariffs. Contact
the state public utility commission, public service commission or
corporation commission for information. This equipment is
hearing aid compatible.
Should you experience trouble with this equipment, please
contact Uniden customer service at 800-297-1023. If the
equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the
equipment until the problem is resolved.
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation. Privacy of communications, may not be
ensured when using this phone.
To insure the safety of users, the FCC has established criteria for
the amount of radio frequency energy various products may
produce depending on their intended usage. This product has been
tested and found to comply with the FCCís exposure criteria. For
body worn operation, the FCC RF exposure guidelines were also
met when used with the Uniden accessories supplied or designed
for this product. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines and should be
avoided.
Radio Interference
Cordless telephones are radio devices. Communications between
the handset and base of your cordless telephone are accomplished
by means of radio waves which are broadcast over the open
airways.
Because of the inherent physical properties of radio waves, your
communications can be received by radio receiving devices other
than your own cordless telephone unit. Consequently, any
communications using your cordless telephone may not be private.
One Year Limited Warranty
Important: Evidence of original purchase is required for warranty
service.
WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden")
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the
original retail owner, this Uniden Product to be free from defects
in materials and craftsmanship with only the limitations or
exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall
terminate and be of no further effect 12 months after the date of
original retail sale. The warranty is invalid if the Product is (A)
damaged or not maintained as reasonable or necessary, (B)
modified, altered, or used as part of any conversion kits,
subassemblies, or any configurations not sold by Uniden, (C)
improperly installed, (D) serviced or repaired by someone other
than an authorized Uniden service center for a defect or
malfunction covered by this warranty, (E) used in any conjunction
with equipment or parts or as part of any system not
manufactured by Uniden, or (F) installed or programmed by
anyone other than as detailed by the owner's manual for this
product.
OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some
states do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may
not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state. This
warranty is void outside the United States of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after
following the instructions in the owner's manual you are certain
that the Product is defective, pack the Product carefully
(preferably in its original packaging). Disconnect the battery from
the Product and separately secure the battery in its own separate
packaging within the shipping carton. The Product should include
all parts and accessories originally packaged with the Product.
Include evidence of original purchase and a note describing the
defect that has caused you to return it. The Product should be
shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
STATEMENT OF REMEDY: In the event that the product does not
conform to this warranty at any time while this warranty is in
effect, warrantor will either, at its option, repair or replace the
defective unit and return it to you without charge for parts,
service, or any other cost (except shipping and handling) incurred
by warrantor or its representatives in connection with the
performance of this warranty. Warrantor, at its option, may replace
the unit with a new or refurbished unit. THE LIMITED WARRANTY
SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY
PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES
ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER
EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT
[40] PRECAUTIONS & WARRANTY
www.uniden.com
PRECAUTIONS &
WA R R A N T Y
Radio interference may occasionally cause buzzing and humming
in your cordless handset, or clicking noises in the base. This
interference is caused by external sources such as TV, refrigerator,
vacuum cleaner, fluorescent lighting, or electrical storm. Your unit
is NOT DEFECTIVE. If these noises continue and are too
distracting, please check around your home to see what
appliances may be causing the problem. In addition, we
recommend that the base not be plugged into a circuit that also
powers a major appliance because of the potential for
interference. Be certain that the antenna on the unit is fully
extended when needed.
In the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving
radio signals from another cordless telephone or other source of
interference. If you cannot eliminate this type of interference, you
need to change to a different channel.
Finally, it should be noted that some cordless telephones operate
at frequencies that may cause interference to nearby TVs and
VCRs. To minimize or prevent such interference, the base of the
cordless telephone should not be placed near or on top of a TV or
VCR. If interference is experienced, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the
interference.
Cordless Telephone Privacy
TERMINAL EQUIPMENT
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity indicating that Industry Canada technical
specifications were met. It does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The
REN assigned to each terminal equipment provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of
all the devices does not exceed five.
RADIO EQUIPMENT
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were
met.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device. “Privacy of communications may not be ensured when using this telephone”.
www.uniden.com
I.C. NOTICE [41]
I.C. NOTICE
I.C. Notice
Index
[42] INDEX
. . . 35
. . . 14
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
35
.9
.9
33
12
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 21
. 28
. 21
. 30
. 31
. 29
. 20
. 10
. 34
. 10
5, 6
. . . 16
. . . 32
. 19
. 21
. 35
. 13
. 41
. .8
. 40
. 38
Troubleshooting . . . . . . . .
V, W, X, Y, Z
Voice mail waiting indicator
Wall mounting . . . . . . . . . .
Warranty . . . . . . . . . . . . .
. . . 36
. . . 22
. . . 11
. . . 40
. 18
. .1
. 39
. .1
INDEX
A
AC adapter information . . . .
B
Basic setup . . . . . . . . . . .
Battery pack
Information . . . . . . . . . .
Installing . . . . . . . . . . .
Preparing and charging . .
Replacement and handling
Beltclip installation . . . . . .
C
Call waiting . . . . . . . . . . .
Caller ID service . . . . . . . .
Call waiting . . . . . . . . . .
Deleting . . . . . . . . . . . .
Making a call . . . . . . . . .
Viewing . . . . . . . . . . . .
Channel . . . . . . . . . . . . . .
Charging the battery pack . .
Cleaning contacts . . . . . . .
Connect the base unit . . . .
Controls and functions . . . .
D
Dial mode . . . . . . . . . . . .
Digital security code . . . . .
E, F, G, H, I, J, K, L
Earpiece volume . . . . . . . . . . .
Find handset . . . . . . . . . . . . .
General information . . . . . . . .
Headset installation . . . . . . . .
I.C. Notice . . . . . . . . . . . . . .
Installing the phone . . . . . . . .
Interference . . . . . . . . . . . . .
Liquid damage . . . . . . . . . . . .
M, N, O, P, Q
Making a call . . . . . . . . . . . . .
Package contents . . . . . . . . . .
Precautions . . . . . . . . . . . . . .
Quick reference guide . . . . . . .
R
Receiving a call . . . . . . . . . . .
Redial . . . . . . . . . . . . . . . . .
Ringer tone . . . . . . . . . . . . . .
S
Speed dial memory
Making calls from speed dial
memory . . . . . . . . . . . . .
Storing names and numbers in
speed dial memory . . . . . .
T, U
Technical information . . . . . . .
Tone dialing switch-over . . . . .
Traveling out-of-range . . . . . . .
. 18
. 19
. 17
. 27
. 23
. 35
. 20
. 20
www.uniden.com
Memory List
C U T
C U T
MEMORY LOCATION MEMO
MEMORY LOCATION MEMO
Memory
Location
Name
Phone Number
Memory
Location
1*
6
2
7
3
8
4
9
5
10
Name
C U T
C U T
MEMORY LOCATION MEMO
MEMORY LOCATION MEMO
Memory
Location
Name
Phone Number
Memory
Location
1*
6
2
7
3
8
4
9
5
10
www.uniden.com
Phone Number
Name
Phone Number
[43]
Memo
[44]
www.uniden.com
At Uniden, we'll take care of you!
Thank you for purchasing a Uniden product. If you have any questions or problems,
please do not return this product to the place of purchase.
Having Trouble?
Our customer care specialists are here to help you! Visit our website at www. uniden.com or
call our Customer Hotline at 1-800-297-1023, Mon-Fri, 7 a.m. to 7 p.m. or Sat/Sun, 9 a.m.
to 5 p.m. CST. (Phone support is closed on holidays.)
Need a part?
To order headsets, additional handsets, replacement batteries or other accessories, visit
our website at www.uniden.com or call 1-800-554-3988, Mon-Fri, 8 a.m. to 5 p.m. CST.
Help for our Special Needs Customers
If you need special assistance due to a disability or have questions on the accessibility
features of this product, please call 1-800-874-9314 (voice or TTY)
May be covered under one or more of the following U.S. patents:
4,797,916 5,381,460 5,426,690 5,434,905 5,491,745 5,493,605
5,533,010 5,574,727 5,581,598 5,650,790 5,660,269 5,661,780
5,663,981 5,671,248 5,696,471 5,717,312 5,732,355 5,754,407
5,758,289 5,768,345 5,787,356 5,794,152 5,801,466 5,825,161
5,864,619 5,893,034 5,912,968 5,915,227 5,929,598 5,930,720
5,960,358 5,987,330 6,044,281 6,070,082 6,125,277 6,253,088
6,314,278 6,418,209 6,618,015 6,671,315 6,714,630 6,782,098
6,788,920 6,788,953
Other patents pending.
S,
R
IE @
M
FO OR E
CO
S
N
.
I
ES NL EN
D
CC
A O O NI
.U
G
W
W
W
R E G I S T E R O N L I N E T O D AY !
T H A N K Y O U F O R B U Y I N G A U N I D E N P R O D U C T.
©2005 Uniden America Corporation, Fort Worth, Texas. Contains additional foreign articles. Custom manufactured in China.
UPZZ01051KZ
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising