English U01UT063HZB(0) GMR3040-2CK GMR3040-3CK • 15 GMRS / 7 FRS Channels • 7 Weather Channels • 121 Sub Codes (CTCSS Tone and DCS Code) • Up to 30 Mile Range* • Internal VOX Circuitry • 10 Selectable Call Tone Alerts • Backlit LCD Display • Headset Jack • Roger Beep • • • • • • • Battery Charger Battery Level Meter Channel Monitor Channel Scan Keypad Lock DC 9V Jack NOAA Emergency / Weather Channels *Range may vary depending on environmental and/or topographical conditions. GMR3040-2CK AND GMR3040-3CK RADIO Congratulations on your purchase of a Uniden GMRS (General Mobile Radio Service) radio. Theselightweight,palm-sized,radiosarestate-ofthe-art devices. Both GMR3040-2CK and -3CK have many top features. Use them at sporting events, to contact family and friends, while hiking, skiing,oroutdoors,orinaneighborhoodwatchfor vital communication. PACKAGE CONTENTS Yourpackagecontainstworadios*,tworechargeable NiMH battery packs*, one AC adapter, one charging cradle, two belt clips*, and this reference guide. A NiMH battery pack or 3 optional AAA alkaline batteries powers each unit.* GMR3040-2CK ; three with the GMR3040-3CK. To order the following optional accessories, visit our websiteatwww.uniden.comorcall1-800-554-3988 during regular business hours. Use only Uniden accessories. • NiMH Battery Pack - #BT-1028 or BP-1028 • Charging Cradle - #RC-1291 • Headset - #ZA-133 and #ZA-160 • AC Adapter - #PS-0007 • DC Adapter - #DC-1002 • Carabiner Clip #TSTD0720002 GMRS LICENSE The radio operates on the General Mobile Radio Service (GMRS) frequencies when using Channels 1-7 and channels 15-22. You must have a GMRS license issued by the Federal Communications Commission to legally use these channels. For licensing information and application forms, visit the FCC online at: www. fcc.gov/wtb/uls or call the FCC hotline at 1-800-418-3676. If you have any questions, you can contact the FCC direct at 1-888-225-5322. No license is required for operation on channels CHARGE 8-14 or operation on any channel in Canada. INSTALL THE BATTERY 1 2 3 4 5 6 7 8 9 10 11 12 Antenna PTT (Push-To-Talk) Button Call/Lock Button Menu/Power Key Channel Up/Down Key Weather/Monitor Key Speaker Headset Jack/DC 9V Volume Up/Down Key Microphone Battery Level Meter Receive Indicator 13 14 15 16 17 18 19 20 21 22 23 24 Call Indicator Scan Indicator Channel Indicator Hi Power Indicator Low Power Indicator Transmit Indicator VolumeSettingIndicator Keypad Lock Indicator VOX Indicator Weather Indicator Sub Code Indicator Charging Contacts Each radio uses a supplied NiMH battery pack or 3 AAA alkaline batteries (not included). To install the NiMH battery pack: 1) Make sure your radio is OFF. 2) Press the tab at the bottom of the battery compartment door to remove the cover. 3) Install the NiMH battery pack into the battery compartment. Be certain to follow the instructions written on the label on the battery pack.Installing the battery packincorrectly will prevent the unit from operating. 4) Replace the battery compartment door. BATTERY LEVEL AND LOW BATTERY ALERT This unit has a battery level meter on the display to indicate the status of the batteries. When the battery in the unit is low, the battery level meter icon flashes. Recharge the NiMH battery pack immediately or if you are using alkaline batteries,youmustreplacethealkalinebatteriesin order to continue using the radio. Warning! To avoid the risk of personal injury or propertydamagefromfireorelectricalshock,only usetheUnidenaccessoriesspecificallydesignated for this product. CHARGING THE RADIO IfyouusetherechargeableNiMHbatterypack,two radios can be charged directly or by using the supplied charging cradle. USING THE RADIO 1) Connect the optional DC adapter (#DC-1002) to DC 9V jack of the radio and to a cigarette lighter port. 2) Charge the battery pack for 16 hours until the battery indicator stops flashing. USING THE CHARGING CRADLE 1) Connect the AC adapter (#PS-0007) to DC 9V jack and to a standard 120V AC wall outlet. 2) Set the charging cradle on the desk or tabletop, and place the radio in the charging cradle with the keypad facing forward. 3) Make sure that the LED illuminates. Charge the battery pack for 16 hours and remove the radio from the charging cradle after charging. Note: • Forchargingbatteriesdirectlywithoutthecradle, useonlythe#DC-1002CigaretteLighterAdapter cord, available from www.Uniden.com. Other power cords could damage your radio. • DC 9V jack of the radio is for charging only. Be sure to install the battery before charging. • Use only the supplied battery and AC adapter or approved accessories from Uniden. • Chargetimemayvarydependingonthebattery life remaining. • Do not recharge alkaline batteries. Doing so can create a safety hazard or damage the radio. • For fastest charging, turn off the radio before charging. • The battery must be installed for the unit to operate, even if the unit is also connected to external power. • If battery power is low, you cannot operate the radio even using external power. Allow the batteries to charge before using. If you try to transmit while power is low, the radio will automatically turn off. USING A HEADSET You can use a headset (#ZA-133 or #ZA-160) for more private communications.To use a headset, lift the rubber cover from over the headset jack, then plug in the headset. Important: Your radio is not weather resistant when using a headset jack.When you remove the headset, be sure to fully press the jack cover into place to restore its weather resistant capability. USING THE RADIO In order to get the most out of your new radio, read thisreferenceguidecompletelybeforeattemptingto operate the unit. TURNING THE RADIO ON AND ADJUSTING THE VOLUME 1) Press and hold MENU/ to turn the radio ON, and increase the speaker volume by pressing VOL ▲ . To decrease the volume, press VOL ▼. 2) Press and hold MENU/ again to turn the radio OFF. TALKING ON YOUR RADIO To talk to others using the radio: 1) Press and hold the PTT button and speak in a clear, normal voice about 2-3 inches away from the microphone. While you are transmitting, the icon appears on the display. To avoid cutting off the first part of your transmission, pause slightly after pressing the PTT button before you start talking. 2) When you have finished speaking, release the PTT button. You can now receive incoming calls.While receiving, displays. MONITOR MODE FEATURE Your radio allows you to listen for weak signals on the current channel at the press of a key. To turn ON Monitor mode: • Press and holdWX/MON for 2 seconds until two beeps sound.The receiver circuit stays open, and both noise and weak signals can be heard. To turn OFF Monitor mode: • Press and hold WX/MON for 2 seconds to return to "Normal" mode; the icon stops blinking and disappears. ADJUSTING THE SOUND (KEY BEEPS) Your radio emits a beep each time one of the keys (except for the PTT and CALL/LOCK) is pressed. To turn this sound OFF, press and hold CALL/ LOCK while turning ON the radio. Repeat this step to turn the sound ON. ADVANCED FUNCTIONS (MENUS) Use MENU/ to access your radio's advanced functions. CHOOSING A CHANNEL Your radio has 22 channels and 121 Sub codes you can use to talk to others. In order to speak to someone, each of you must be set to the same channel and Sub code. Sub Code OFF, 1-121 Call Tone Scan ON/OFF Normal To choose a channel: With the radio in "Normal" operating mode, press the CH ▲ / CH ▼ key to increase or decrease the channel number displayed. Note: Channels 1-7 have a typical range of up to 30 miles. Channels 8-14 have a typical range of up to 5 miles. Channels 15-22 have a typical range of up to 30 miles. You can see which GMRS or FRS channel is active by the icon. The hi icon is displayed while scanning GMRS channels, and the lo icon is displayed while scanning FRS channels. VOX Level Normal OFF, 1-5 1-10 1) Press MENU/ to enter the menus. 2) AdditionalpressesofMENU/ advanceyou throughthemenus untilexiting to"Normal" operating mode. 3) OthermethodsofexitingtheMenufunction are: a. Press and hold MENU/ again. b. Press any key except CH ▲ / CH ▼ or VOL ▲ / VOL ▼ and wait 10 seconds until the unit returns to “Normal” mode. Sub Code Each of the channels 1-22 may have any one of the codes, OFF, or 1-121 selected. Code oF (OFF) indicates no Sub code selected and your radio can receive a signal regardless of the code settings of the transmitting radio. 1) Press MENU/ to enter Menu mode. The subcode indicator flashes. 2) Press CH ▲ / CH ▼ key to increase or decrease the code number displayed. You can also select oF (OFF) at this stage. 3) Press MENU/ to exit Menu mode. 4) Press any key other than CH ▲ / CH ▼ or VOL ▲ / VOL ▼ and the radio returns to Idle mode in 10 seconds. Scan Your radio has a channel scan feature that allows you to easily scan all 22 channels.When an active channel is detected, the radio pauses on that channel until the channel is clear.Then, after a 2 second delay, the radio continues scanning. Pressing the PTT button while the scan is paused on a channel allows you to transmit on that channel. To turn ON channel scan: 1) Press MENU/ repeatedly until the scan... icon and oF blink. 2. Press CH ▲ / CH ▼ to select Scan mode and press MENU/ to start it. To turn OFF channel scan: 1) Press MENU/ when the scan setting is oF. 2) Press any key other than CH ▲ / CH ▼ or VOL ▲ / VOL ▼ to turn channel scan off in 10 seconds. Voice Operated Transmission Your radio is equipped with a user selectable Voice Operated Transmitter (VOX) that can be used for automatic voice transmissions. The VOX feature is designed to be used with or without a headset with a microphone. Transmission is initiated by speaking into the microphone instead of pressing PTT. To select VOX level: 1) Press MENU/ repeatedly until the vox icon and theVOX sensitivity level (OFF, 1-5) blink. 2) Press CH ▲ / CH ▼ to change the VOX sensitivity levels. Use level 1 for increased sensitivity to voice in normally quiet environments, and use a higher level to reduce undesired activation in very noisy environments. Call Tone Your radio is equipped with 10 selectable call tones that are transmitted when CALL/LOCK is pressed. To select a call tone: 1) Press MENU/ repeatedly until the CALL icon and Call Tone start to blink on the display. 2) Press CH ▲ / CH ▼ to move through the available call tones. Each tone will be heard through the speaker but will not be transmitted. Cycle through these tones and stay on the tone you want to select. 3) Exit Call Tone to set the selected tone. KEY LOCK To lock the keypad: 1) Press and hold CALL/LOCK; displays. These functions are not affected by Key Lock: • Volume adjust • Call tone transmission • Enter monitor mode • PTT transmission • Power off To unlock the keypad: 1) Press and hold CALL/LOCK again; disappears. AUTOMATIC POWER SAVE Your radio has a circuit designed to dramatically extend the life of the batteries. If there is no transmission or an incoming call within 3 seconds, your radio switches to Power Save mode.The radio is still able to receive transmissions in this mode. LCD BACKLIGHT The LCD Backlight automatically turns ON when any key (except the PTT button) is pressed. The LCD display illuminates for 10 seconds before turning OFF. ROGER BEEP Roger Beep is a BEEP that is sent to notify the end of transmission (both PTT and VOX transmission). Roger Beep can be heard through the speaker when both Roger Beep and Key Beep are set to ON.When Roger Beep is set to ON and Key Beep is set to OFF, Roger Beep will not be heard from the speaker but it willbetransmittedtoyourparty.WhenRogerBeepis set to OFF, Roger Beep will neither be heard nor transmitted. To change Roger Beep setting: Press and holdVOL ▲ while turning the radio on and off. If Roger Beep is ON, it will be turned off; if it is OFF, it will be turned on. USING THE WEATHER RADIO Your radio can receive weather broadcasts from the NOAA National Weather Service. While using the Weather Radio, you are not able to receive GMRS communications. 1) To turn on the Weather Radio Broadcast mode, press WX/MON. The icon appears. 2) Press CH ▲ / CH ▼ to increase or decrease the number to the desired Weather Channel. 3) To exit the Weather Radio Broadcast mode, press WX/MON. The icon disappears. NOAA Weather Radio Frequency List Channel 1 162.550 MHz Channel 5 162.450 MHz Channel 2 162.400 MHz Channel 6 162.500 MHz Channel 3 162.475 MHz Channel 7 162.525 MHz Channel 4 162.425 MHz SPECIFICATIONS Channels Sub Codes 15 GMRS/7 FRS/7 Weather 38 Sub-Audible Tones 83 DCS Codes Operating Frequency GMRS/FRS: 462.5500 - 467.7125 MHz WX: 162.4000 - 162.5500 MHz Power Source NiMH Battery Pack (BT-1028 or BP-1028) or 3 AAA Alkaline Batteries Range Channel 1-7 up to 30 miles Channel 8-14 up to 5 miles Channel 15-22 up to 30 miles Battery Life 10 Hours typ. - NiMH Battery Pack (5/5/90 duty cycle) Frequency Chart Ch. 1 2 3 4 5 6 7 8 9 10 11 Freq. 462.5625 462.5875 462.6125 462.6375 462.6625 462.6875 462.7125 467.5625 467.5875 467.6125 467.6375 Cross Ref. FRS & GMRS 1 FRS & GMRS 2 FRS & GMRS 3 FRS & GMRS 4 FRS & GMRS 5 FRS & GMRS 6 FRS & GMRS 7 FRS 8 FRS 9 FRS 10 FRS 11 Ch. 12 13 14 15 16 17 18 19 20 21 22 Freq. 467.6625 467.6875 467.7125 462.5500 462.5750 462.6000 462.6250 462.6500 462.6750 462.7000 462.7250 Cross Ref. FRS 12 FRS 13 FRS 14 GMRS 11 GMRS 8 GMRS 12 GMRS 9 GMRS 13 GMRS 10 GMRS 14 GMRS 15 CTCSS Chart (Hz) Code oF 1 Freq. OFF 67.0 Code 20 21 Freq. 131.8 136.5 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 DCS Code List Tone Octal Tone Octal No. Code No. Code 39 023 67 174 40 025 68 205 41 026 69 223 42 031 70 226 43 032 71 243 44 043 72 244 45 047 73 245 46 051 74 251 47 054 75 261 48 065 76 263 49 071 77 265 50 072 78 271 51 073 79 306 52 074 80 311 53 114 81 315 54 115 82 331 55 116 83 343 56 125 84 346 57 131 85 351 58 132 86 364 59 134 87 365 60 143 88 371 61 152 89 411 62 155 90 412 63 156 91 413 64 162 92 423 65 165 93 431 66 172 94 432 141.3 146.2 151.4 156.7 162.2 167.9 173.8 179.9 186.2 192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3 Tone Octal No. Code 95 445 96 464 97 465 98 466 99 503 100 506 101 516 102 532 103 546 104 565 105 606 106 612 107 624 108 627 109 631 110 632 111 654 112 662 113 664 114 703 115 712 116 723 117 731 118 732 119 734 120 743 121 754 RBRC INFORMATION As part of our commitment to protect the environment and conserve natural resources, Uniden voluntarily participates in an RBRC® industry program to collect and recycle used Ni-MH batteries within the US. Please call 1-800-8-BATTERY for information on Ni-MH battery recycling in your area. (RBRC® is a registered trademark of the Rechargeable Battery Recycling Corporation.) Care and Safety: To clean the radio, use a soft cloth dampenedwithwater.Donotusecleanersorsolvents because they can harm the body of the unit and leak inside,causingpermanentdamage.Useadry,lint-free cloth to clean the battery contacts.Donotsubmergetheunitinwater.Iftheunit gets wet, turn it off and remove the batteries immediately. Dry the battery compartment with a soft cloth to minimize potential water damage. Leave the battery compartment cover off overnight to ensure complete drying. Do not use the radio until the unit is completely dry. REGULATORY INFORMATION RF EXPOSURE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)Thisdevicemaynotcauseharmfulinterference. (2) This device must accept any interference received, including interference that may cause undesired operation. Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device.Your radio is set up to transmit a regulated signal on an assigned frequency. It is againstthelawtoalteroradjustthesettingsinside the radio to exceed those limitations. Any adjustments to your radio must be made by qualified technicians. To be safe and sure: • Never open your radio’s case. • Never change or replace anything in your radio except the batteries. Your radio might cause TV or radio interference even when it is operating properly.To determine whetheryourradioiscausingtheinterference,turn it off. If the interference goes away, your radio is causing it. Try to eliminate the interference by moving your radio away from the receiver. If you cannoteliminatetheinterference,theFCCrequires that you stop using the radio. Hazardous Environments: Do not operate the radioinhazardousenvironments.Explosionorfire may result. Do not operate the radio near unshielded electrical blasting caps. Undercertainconditions,radioscaninterferewith blasting operations and may cause an explosion. Turn your radio OFF to prevent accidental transmission when in a blasting area or in areas posted: "Turn off two-way radio." Construction crews often use remote control RF devices to set off explosives. WARNING! Read this information before using the radio. In August 1996 the Federal CommunicationsCommission(FCC)oftheUnited States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagneticenergyemittedbyFCCregulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies.The design of the radio complies with the FCC guidelines and these international standards. Never allow children to operate the radio without adult supervision and the knowledge of the following guidelines. WARNING! It is up to the user to properly operate this radio transmitter to insure safe operation. Please adhere to the following: Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachmentscouldimpaircallquality,damagethe radio, or result in violation of FCC regulations. Do not use the radio with a damaged antenna. Ifadamagedantennacomesintocontactwiththe skin, a minor burn may result. Please contact your local dealer for a replacement antenna. Hand-held Operation (Held-to-Face) This device was evaluated for typical hand-held (held-to-face)operationswitha1inchspacingfrom thefrontoftheradio.Forhand-heldoperation,the radio should be held 1 inch from the user's face in order to comply with FCC RF exposure requirements. Body-worn Operation Thisdevicewasevaluatedforbody-wornoperations withthesuppliedbelt-clipaccessory. (Allnecessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) shouldbeavoidedasthesemightnotcomplywithFCC RF exposure guidelines. For more information about RF exposure, please visit the FCC web site at www.fcc.gov. THREE YEAR LIMITED WARRANTY Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden warrants, for three years, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanshipwithonlythelimitationsorexclusions set out below. WARRANTY DURATION: This warranty to the originalusershallterminateandbeofnofurthereffect 36 months after the date of original retail sale. The warranty is invalid if the Product is: (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, sub-assemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other thananauthorizedUnidenservicecenterforadefect or malfunction covered by this warranty, (E) used in anyconjunctionwithequipmentorpartsoraspartof any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s manual for this product. STATEMENT OF REMEDY: In the event that the productdoesnotconformtothiswarrantyatanytime whilethiswarrantyisineffect,warrantorwilleither,at its option, repair or replace the defective unit and return it to you without charge for parts, service, or anyothercost(exceptshippingandhandling)incurred by warrantor or its representativesinconnectionwiththeperformanceof thiswarranty.Warrantor,atitsoption,mayreplacethe unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OVERPAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation ofincidentalorconsequentialdamagessotheabove limitation or exclusion may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.This warranty is void outside the United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE OFWARRANTY: If, after following the instructions in the owner’s manual you are certain that the Product isdefective,packtheProductcarefully(preferablyin its original packaging). Disconnect the battery from the Product and separately secure the battery in its ownseparatepackagingwithintheshippingcarton. TheProductshouldincludeallpartsandaccessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it.The Product should be shipped freight prepaid, by traceable means, to warrantor at: Uniden America Service 4700 Amon Carter Blvd. Fort Worth, TX 76155 (800) 297-1023 during regular business hours (CST) (Seewww.uniden.comforcurrenthoursofoperation.) © 2012 Uniden America Corporation All rights reserved. Printed inVietnam.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project