Uniden | MER9600C | Owner Manual | Uniden MER9600C Owner Manual

Uniden MER9600C Owner Manual
CONTENTS
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
I.C. Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Included with Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Important Electrical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . 7
Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Telephone Line Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Radio Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
More Than One Cordless Telephone . . . . . . . . . . . . . . . . . . . . . 8
Installing Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Selecting the Installation Location . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting the Telephone Line . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting the Telephone Cords . . . . . . . . . . . . . . . . . . . . . . . 10
Applying Power to the Base Unit . . . . . . . . . . . . . . . . . . . . . . . . 11
Adapter Safety Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Applying Power to the Charging Unit . . . . . . . . . . . . . . . . . . . . . 12
Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing the Handset Battery Pack . . . . . . . . . . . . . . . . . . . . . . 18
Charging the Handset Battery Pack . . . . . . . . . . . . . . . . . . . . . 19
Charging Spare Battery Packs . . . . . . . . . . . . . . . . . . . . . . . . . 19
Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning the Charging Contacts . . . . . . . . . . . . . . . . . . . . . . . . 20
Using Your Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
MER 9600C Handset Controls . . . . . . . . . . . . . . . . . . . . . . . 21
Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Configuring the MER 9600C . . . . . . . . . . . . . . . . . . . . . . . . . 23
Deleting Configuration Items . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Using Your Handset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Answering a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Switching the Call to a Host Phone . . . . . . . . . . . . . . . . . . . . . . 28
Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Special Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Placing a Call On Hold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Transferring a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Setting up a Conference Call . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Muting a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Lock Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Your EXP9530 Headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Optional Backup Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Accessories and Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 35
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
1
Important Safety Instructions
When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electrical shock,
and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a dry cloth for
cleaning.
4. Do not use this product near water; for example, near a sink or
in a wet area.
5. Do not place this product on an unstable cart, stand, or table.
The telephone may fall, causing serious damage to the unit.
6. To protect the product from overheating, do not block or cover
any slots or openings in the base Unit. This product should
never be placed near or over a radiator or heat register. This
product should not be placed in a built-in installation unless
proper ventilation is provided.
7. This product should be operated only from the type of power
source indicated on the marking label.
8. Do not allow anything to rest on the power cord. Do not locate
this product where the cord will be damaged by persons
walking on it.
9. Do not overload wall outlets and extension cords, as this can
result in the risk of fire or electrical shock.
10. Never push objects of any kind into this product through the
Base Unit slots, as they may touch dangerous voltage points or
short out parts that could result in a risk of fire or electric shock.
Never spill liquid of any kind on the product.
11. To reduce the risk of electric shock, do not disassemble this
product. Contact qualified service personnel when some service
or repair work is required. Opening or removing covers may
expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the appliance is
subsequently used.
2
12. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power supply cord is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when following the
operating instructions. Adjust only those controls that are
covered by the operating instructions. Improper adjustment
of other controls may result in damage, and will often
require extensive work by a qualified technician to restore
the product to normal operation.
E. If the product has been dropped, or the cabinet has been
damaged.
F. If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leak in the vicinity of
the leak.
CAUTION: To reduce the risk of fire or injury to persons by the battery,
read and follow these instructions:
14. Use only the appropriate type and size Battery Pack specified in
this Operating Guide.
15. Do not dispose of the Battery Pack in a fire. The cell may
explode.
16. Do not open or mutilate the Battery Pack. Released electrolyte
is corrosive and may cause damage to the eyes or skin. It may
be toxic if swallowed.
17. Exercise care in handling the battery in order not to short the
battery with conducting materials such as rings, bracelets, and
keys. The battery or conductor may overheat and cause burns.
18. Charge the Battery Pack provided with or identified for use with
this product only in accordance with the instructions and
limitations specified in the instruction manual provided for this
product.
19. Observe proper polarity orientation between the Battery Pack
and battery charger.
SAVE THESE INSTRUCTIONS
3
I.C. Notice
“Notice: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommunications
network protective, operational and safety requirements. The Department
does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection. In some cases, the
company’s inside wiring associated with a single line individual
service may be extended by means of a certified connector assembly
(telephone extension cord). The customer should be aware that
compliance with the above conditions may not prevent degradation of
service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority, or electrician,
as appropriate.”
“Notice: This cordless telephone uses radio communications between the
handset and the base set, and may not ensure privacy of communication.
Other devices including other cordless telephones may interfere with the
operation of this cordless telephone or cause noise during operation. Units
not containing coded access signaling could be accessed by other cordless
telephones or radio communications systems. Cordless telephones must no
cause interference to any licensed radio service.”
4
About Your Phone
Congratulations on your purchase of the Uniden MER 9600C
Cordless Telephone. It is designed and engineered to exacting
standards for reliability, long life, and outstanding performance. It is
designed to work with a PBX system. To get the most from new
phone, please read this Operating Guide thoroughly. To help
familiarize you with the features of your cordless phone, refer to the
Handset illustration foldout from the front cover, and the Base Unit
illustration foldout from the rear cover.
Features
Super Long Range 900MHz Digital
2-line, 16-digit LCD Display
Headset Jack
Channel Selection Control
Ringer Volume Control
Handset Volume Control
Single key access to: CONFERENCE, HOLD, TRANSFER and
MUTE features
Four Programmable Function Keys: F1 – F4
Separate Charging Stand with Spare Battery Charging
Capability
Second Spare Battery
AutoStandby
AutoTalk
Vibrator Ringer Alert
Easy Installation
Out of Range Protection
Low Battery Protection System
Key Pad Lock Feature
Wall Mountable separate Base Unit
Wall Mountable separate Charging Unit
5
Included with Your Phone
If any of these items are missing or damaged, contact your PBX
Administrator. If your phone is not performing to your expectations,
please try the simple steps listed in the Trouble Shooting Section of
this Guide. If you are still unable to resolve the problem, contact your
PBX Administrator.
talk
bat low
lock
msg
vol
chan
talk
F1
xfer
F2
f
con
F3
hold
F4
mute
f
3de
c
2ab
6mno
1
yz
5jkl
i
9wx
4gh
tuv
8
rs
#
er
7pq
0op
Base Unit
Handset
Telephone Cord
2 AC Adapters
(2 different types)
2 Rechargeable
Batteries
Belt Clip
Ope
Battery Charger
ratin
R
g Gu
ide
Operating Guide
OMMER9600
6
Wall Mounting Plate
Important Electrical Considerations
Warning: Please do not attempt to unplug any appliance during
an electrical storm.
Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiring and
damage any device connected to it. This phone is no exception.
Caution:
Changes or modifications to this product not expressly
approved by Uniden, or operation of this product in any
way other than as detailed by this Operating Guide, could
void your authority to operate this product.
Range
Your new phone is designed to achieve the maximum possible range
by transmitting and receiving according to the highest specifications
set forth by the FCC. We have rated this phone to operate at a
maximum distance with the qualification that the range depends upon
the environment in which the telephone is used. Many factors limit
range, and it would be impossible to include all the variables in our
rating. The Maximum Range rating of this phone is meant to be used
as a means of comparison against other range claims.
Telephone Line Problems
The FCC has granted the telephone company the right to disconnect
service in the event that your phone causes problems on the
telephone line. Also, the telephone company may make changes in
facilities and services which may affect the operation of your unit.
However, your telephone company must give adequate notice in
writing prior to such actions to allow you time for making necessary
arrangements to continue uninterrupted service.
If you are having trouble with your telephone service, you must first
disconnect your phone to determine if it is the cause of your problem.
If you determine that it is the cause, you must leave it disconnected
until the trouble has been corrected.
7
Radio Interference
Radio interference may occasionally cause buzzing and humming in
your cordless Handset, or clicking noises in the Base Unit. This
interference is caused by external sources such as TV, refrigerator,
vacuum cleaner, fluorescent lighting, or electrical storm. Your unit is
NOT DEFECTIVE. If these noises continue and are too distracting,
please check around your office to see what appliances may be
causing the problem. In addition, we recommend that the Base not be
plugged into a circuit that also powers a major appliance because of
the potential for interference. Be certain that the antenna on the unit is
fully extended when needed.
In the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving radio
signals from another cordless telephone or other source of
interference. If you cannot eliminate this type of interference, you
need to change to a different channel.
Finally, it should be noted that some cordless telephones operate at
frequencies that may cause interference to nearby TVs and VCRs. To
minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV or VCR. If
interference is experienced, moving the cordless telephone farther
away from the TV or VCR will often reduce or eliminate the
interference.
More Than One Cordless Telephone
If you want to use more than one cordless telephone in your office,
they must operate on different channels. This telephone will
automatically select a channel that provides the clearest
communication.
8
Installing Your Phone
Selecting the Installation Location
Select a location that avoids excessive heat or humidity. The Base
can be placed on a desk or tabletop near a standard 120V AC outlet
and telephone line jack, or it can also be mounted on a standard
AT&T or GTE wall plate using the Wall Mount Adapter included with
your telephone. Place this Base Unit near the desk unit. Keep the
Base and Handset away from sources of electrical noise such as
motors, fluorescent lighting, or computers.
Connecting the Telephone Line
There are two types of phone outlets:
Modular Jack
Plug the telephone line cord from the Base Unit into a standard
modular telephone jack. (Note: If you do not have a modular jack,
contact your PBX Administrator for information on the installation of
these jacks.)
Hard-wired Jack
A modular jack converter (not included) is required. You may need to
rewire when connecting the converter (making color-coded
connections).
Note:
Your Uniden Telephone Dealer or a telephone supply store
can advise you on the proper adapter or converter.
9
Connecting the Telephone Cords
The MER 9600C must be connected to a digital PBX port.
CAUTION:
Never install telephone wiring during a lightning storm.
Never touch none insulated telephone wires or terminals unless
the telephone line has been disconnected at the network
interface.
Use caution when installing or modifying telephone lines.
Line in
From
Telephone
Jack
You must also connect a Meridian desk phone to the MER 9600C:
To Meridian
Desk Phone
Connect to the LINE OUT Jack
10
Applying Power to the Base Unit
Route the power cord where it will not create a trip hazard, or where it
could become chafed and create a fire or other electrical hazards.
AC
Adapter
Line in
From
Telephone
Jack
Line out
to Meridian
Desk Phone
Note:
Use only the supplied AC Adapter AD9500 for the Base.
Adapter Safety Feature
The AC Adapter furnished with this phone may be equipped with a
polarized line plug (a plug having one blade wider than the other.)
This plug will fit into the power outlet only one way. If you are unable
to insert the plug fully into the outlet, try reversing the plug.
Do not alter the shape of the
blades of the polarized plug.
Note:
If you cannot plug the AC Adapter into the outlet, contact
someone about replacing the outlet.
11
Applying Power to the Charging Unit
The unique design of your phone allows you to place the Handset in
the Charging Unit with or without the Belt Clip attached. The Charging
Unit also has the ability to charge a second battery with or without the
Handset being charged. The Battery Packs can automatically be
recharged either in or out of the Handset.
AC
Adapter
Note:
Use only the supplied AC Adapter AD960 for the charging
unit.
Before using your MER 9600C, be sure to raise the antenna to the
vertical position.
12
Wall Installation
Standard Wall Plate Mounting
The Base Unit is designed to be mounted on a standard AT&T or
GTE wall plate. To attach the wall mount stand to the Base Unit:
1. Slide the Wall Mount stand
into the notches at the top of
the Base Unit, rotate the wall
mount stand down and snap
it into place.
2. Plug the AC Adapter into the Base Unit as previously described.
3. Place the AC Adapter cord
inside the molded channel of
the Wall Mount stand.
4. Plug one end of the short telephone cord into the LINE jack on
the Base Unit. Then plug one end of a Meridian desk phone line
into the PHONE jack. Place the Telephone cords inside the
molded channels on the bottom of the Wall Mount stand.
5. Plug the other end of the short telephone cord into the modular
wall jack in the center of the wall plate.
6. Place the Base Unit on the
posts of the wall plate and
push down until it’s firmly
seated.
13
7. Plug the AC Adapter into a
standard 120V AC wall outlet.
Note:
Do not use an outlet controlled by a wall switch.
Direct Wall Mounting
If you do not have a standard wall plate, you can mount your phone
directly on a wall. Before mounting your phone, consider the following:
Select a location away from electrical cables, pipes, or other
items behind the mounting location that could cause a hazard
when inserting screws into the wall.
Make sure the wall material is capable of supporting the weight
of the Base unit.
Use #10 screws with anchoring devices suitable for the wall
material where the Base Unit will be placed.
1. Insert two mounting screws
315⁄16 inches apart. Allow
about 3⁄16 of an inch between
the wall and screw heads for
mounting the phone.
2. Plug and secure the AC Adapter cord by following steps 2 and
3 of the Standard Wall Plate Mounting.
14
3. Plug one end of the short
telephone cord into the LINE
jack on the Base Unit. Then
plug one end of a Meridian
desk phone line into the
PHONE jack. Place the
Telephone cords inside the
molded channels on the
bottom of the Wall Mount
stand.
4. Place the Base Unit on the
posts of the wall screws and
push down until it’s firmly
seated.
3/16 in.
3 15/16 in.
5. Plug the other end of the
short telephone cord into a
telephone wall jack.
6. Plug the AC Adapter into a standard 120V AC wall outlet by
following step 7 of the Standard Wall Plate Mounting.
Charging Unit Wall Mounting
The Charging Unit is also designed to be wall mounted. you can
mount your phone directly on a wall. Before mounting your Charging
Unit, consider the following:
Select a location away from electrical cables, pipes, or other
items behind the mounting location that could cause a hazard
when inserting screws into the wall.
Make sure the wall material is capable of supporting the weight
of the Charging Unit.
15
Use #10 screws with anchoring devices suitable for the wall
material where the Charging Unit will be placed.
1. Insert two mounting screws
1 12 inches apart. Allow about
3⁄
16 of an inch between the
wall and screw heads for
mounting the phone.
3/16"
1 1/2"
Strain
Relief
2. Plug the AC Adapter into the
Charging Unit as previously
described. Wrap the AC
Adapter cord around the
strain relief.
3. Place the Charging Unit on
the posts of the wall screws
and push down until it’s firmly
seated.
Strain
Relief
3/16"
1 1/2"
4. Plug the AC Adapter into a
standard 120V AC wall outlet.
AC
Adapter
16
Attaching the Belt Clip
You can use the Belt Clip to attach the Handset to your belt or pocket
for convenient portability.
1. Snap the tab out of the Belt
Clip notch on the top of the
Handset.
2. Slide the clip into the tab slot.
Note: The Belt Clip is
designed to fit snugly onto the
Handset.
3. Press firmly until it snaps into
place.
4. To remove, simply press the
retaining clip in toward the
Belt Clip blade and slide the
clip up at the same time.
Once the Belt Clip is removed
remember to re-install the
cover tab.
17
Installing the Handset Battery Pack
1. Remove the battery cover by
pressing the latch and sliding
the cover down and off of the
Handset.
2. Slide the Battery Pack down
into the Handset.
Note: You may have to
remove the old battery at this
time.
3. Place the cover and sliding
the cover up until it latches
into the Handset.
18
NOTCH
Charging the Handset Battery Pack
The rechargeable battery pack must be fully charged before using
your MER 9600C for the first time. (Note: Charge the Battery Pack
without interruption for 5 hours.)
1. Place the Handset in the front
slot of the Charging Unit.
2. Make sure the CHARGE 1
indicator lights. If the
CHARGE 1 light doesn’t light,
check to see that the AC
Adapter is plugged in, and
that the Handset is making
good contact with the
Charging Unit charging
contacts.
Note:
The Charge 1 LED will remain on even when charging is complete.
Charging Spare Battery Packs
The Charging Unit of your MER 9600C is equipped with a Battery
Charger for charging a Spare Battery Pack.
1. Slide the Spare Battery Pack into the second slot in the Charging
Unit until the retaining clip snaps over the top of the pack.
2. Make sure the CHARGE 2
indicator lights. If the
CHARGE 2 indicator doesn’t
light, check to see that the AC
Adapter is plugged in, and
that the Battery Pack is
making good contact with the
Charging Unit charging
contacts.
Note:
Charge the Spare Battery Pack without interruption for 5
hours.
3. Charging is complete when the Charge 2 LED goes off
automatically.
19
4. After charging is complete, press out on the latch and remove
the Battery Pack for use. Or, if you don’t need the Battery pack
immediately, leave it in the Charging Compartment (It will not
overcharge.)
Low Battery Indicator
When the Battery Pack in the
Handset is low and needs to be
charged, you will see the bat low
icon appear on the display. If you are
on a call you will also hear a beep
every 3 seconds.
On a Call
bat low
In Standby Mode
Only the talk key operates.
None of the keys operate.
Handset beeps once every 3 seconds
Handset beeps every 15 seconds for 15
minutes.
Complete your call as quickly as possible
Cannot make call.
Replace Battery pack within 20 seconds
to continue call.
Replace Battery Pack before making a
call.
Return the Handset to the Charging Unit for charging or replace the
Handset Battery Pack with another charged Battery Pack.
Cleaning the Charging Contacts
To maintain a good charge, it is important to clean all charging
contacts on the Handset and Charging Unit about once a month. Use
a pencil eraser or other contact cleaner. Do not use any liquids or
solvents.
20
Using Your Handset
Note:
Operation of the MER 9600C is performed using the
Handset off the Charging Unit.
MER 9600C Handset Controls
talk
chan
Condition
Action
Talk Key (Standby Mode)
Press talk key to make a
call. The phone first
acquires a link to the base
vol
then you hear a dial tone
and the display shows that
the phone is ready for you
to dial the number.
Channel Key (During a call
)
Handset Earpiece Volume
(During a Call)
Press chan, the talk
indicator flashes Twice as
the Base Unit switches to
a different channel.
Press vol on the front of
the Handset to select a
high, or low Earpiece
volume level.
21
LCD Display
AQUIRING
LINK
talk
talk
No display indications
Condition
Ringer Select (Standby
Mode)
Action
LCD Display
Press vol on the front of
the Handset to select one
of the following settings:
Ring Type A (High)
RING TYPE A
HIGH
Ring Type A (Low)
RING TYPE A
LOW
Ring Type B (High)
RING TYPE B
HIGH
Ring Type B (Low)
RING TYPE B
LOW
Ring Off (Vibrate)
RING OFF
22
Initial Setup
Configuring the MER 9600C
Before you can place or receive calls, you must configure your
MER 9600C to match the operation of your host telephone. You
must configure one of the Function Buttons (1 – 4) as your primary
extension.
If you press talk key before
you configure the phone, you
will see an error message on
the LCD:
NO CONFIG
1. Remove the handset from the base unit.
2. Press and hold the
3. While holding
and # keys at the same time.
and #, press the talk key.
4. Release all 3 keys. You will
now see a message on the
LCD prompting you to
configure the F1 function key.
Note:
PROGRAM
BTN F1
You can assign any function to F1 that you have on your
Host Telephone. For example; this can be a line key, call
forwarding key, pickup key, etc.
A * in the display indicates
that function key has already
been programmed.
PROGRAM
BTN F1 *
5. Press the key on the Host Telephone that has the function you
want to assign to F1. You will hear a beep to acknowledge that
the function has been assigned to the key, and a * will appear
to the lower right on the LCD.
6. You will see a new message
on the LCD prompting you to
configure F2.
PROGRAM
BTN F2
Follow the same procedure you used for F1. Proceed in the same
way for F3, F4, xfer, and conf.
23
Note:
The operation of these functions depends on how your Host
Telephone operates with your PBX system. For the 2317
Telephone do not program the xfer and conf functions.
7. After the keys are configured,
you will see the message:
PROGRAM
LCD MSG
If the Message key is
assigned to one of the
function keys of your host
phone, press the message
key of the host phone.
Otherwise, proceed to step 8
without pressing any keys.
8. When you have configured all
the keys, press talk. You will
see:
CONFIG
COMPLETE
The configuration is now
stored and the
MER 9600C returns to
Standby. At this point, you
can use the MER 9600C.
At any time during the Configure process, you can use the vol and
chan keys on the front of the handset to scroll backward or forward
through the configuration options. If you scroll past a Function Key or
other keys without configuring it, that key will be inoperative on your
MER 9600C.
Deleting Configuration Items
You can delete any configuration option by selecting that option and
entering 0.
Example: Delete the option for F4.
1. Press and hold the
2. While holding the
and # keys.
and # keys, press talk key.
3. Release all 3 keys. You will
now see a message on the
LCD prompting you to
configure the F1 function key.
24
PROGRAM
BTN F1
4. Press the chan key until the
F4 option is displayed on the
LCD.
5. Enter 0. The asterisk will go
out.
PROGRAM
BTN F4 *
PROGRAM
BTN F4
6. When you have configured all
the keys, press the talk key.
You will see:
CONFIG
COMPLETE
The configuration is now
stored and the
MER 9600C returns to
Standby. At this point, you
can use the MER 9600C.
Using Your Handset
When you pick up the Handset and
press the talk key, you will see:
AQUIRING
LINK
After the link has been made
between the Handset and Base, you
will see:
talk
Then you’ll see one of the following:
Condition
Indicator
LCD Display
Line OK
talk Icon
talk icon
No Connection to Base
Unit
Error Tone
NO SERVICE
Channel Busy
Error Tone
SYSTEM
BUSY
25
Condition
Line in Use
Indicator
Error Tone
LCD Display
LINE IN USE
When communication is made
between the Base Unit and the
Handset, the screen will go to
“Standby”, and the phone is ready to
use.
If the Handset is at the range limit of
the MER 9600C, you may see:
talk
NO SERVICE
Take the following action:
During a Call
In Standby Mode
Condition
Warning Tone
Can’t make or answer calls
(Phone may ring intermittently)
Action
Move back in range within 20
seconds
Move back within range.
Answering a Call
If the Handset is in the Charger Unit:
1. When you receive a call, the
Handset rings and the LCD
will display a PBX message
showing information about the
call. Also, if one of the
Function Keys (F) is assigned
to a line, the LED for that key
flashes.
A=OUTSIDE CALL1
02
2. Pick up the Handset from the changing unit, this will activate the
AutoTalk feature that allows you to answer the call immediately.
—OR—
Press the talk or the flashing
F key. The next LCD display
you will see is:
26
AQUIRING
LINK
Once the phone has acquired
the link, the call is connected
and you will see:
If a F key was pressed the
corresponding LED will also
be on steady.
A=OUTSIDE CALL1
02
talk
3. When you finish the call, place the Handset back in the Charger
Unit. AutoStandby automatically hangs up the phone.
—OR—
If the Handset is away from the Charger Unit, press the talk key
this will hang up the phone and put it in AutoStandby.
Answering a Call with the Host Telephone
When you receive a call, answer with the Host Telephone as you
normally do.
Completing the Call with the Host Telephone
When you finish the call, hang up the Host Telephone.
1
2
3
Switching the Call on the Host Phone to the MER 9600C
If the Handset is in the Charger Unit
1. Press cordless on the Base Unit. The cordless LED flashes.
2. Hang up the Host Telephone. The cordless and desk LED’s
flash.
3. Pick up the Handset within 20 seconds. AutoTalk allows you to
now begin your conversation.
4. When you finish the call, place the Handset back in the Charger
Unit. AutoStandby automatically hangs up the phone.
27
If the Handset is not in the Charger Unit:
1. Press cordless on the Base Unit. The cordless LED flashes.
2. Hang up the Host Telephone. The cordless and desk LED’s
flash.
3. Press talk on the Handset within 20 seconds to answer the call.
4. When you are finished with the call, press talk to hang up the
phone, or return the Handset to the Charger Unit.
Switching the Call to a Host Phone
1. Press desk on the Base Unit. The desk LED flashes.
2. Hang up the MER 9600C. The cordless and desk LED’s
flash.
3. Pick up the host phone Handset within 20 seconds and begin
your conversation.
4. When you finish the call, place the host phone Handset back on
the host phone Base.
Making a Call
1. Remove the Handset from the Charger Unit.
—OR—
2. Press the talk key. The talk
icon appears after the
Handset and Base are
connected, and you will see:
talk
When you hear a dial tone,
enter the number you are
calling.
5551212
talk
28
3. When you finish the call, place the Handset back in the Charger
Unit. AutoStandby automatically hangs up the phone.
—OR—
If the Handset is away from the Charger Unit, press the talk key
this will hang up the phone and put it in AutoStandby.
If the number is Busy
If the number that you are trying to call is busy, the LCD will display:
RELEASE &
TRY AGAIN
29
Special Operations
You can place a call on hold, transfer a call to another extension,
connect two or more parties in a conference call or mute a call. These
operations except mute, depend upon how they are set up on your
PBX system. Contact your PBX Administrator of more information. If
you have configured the MER 9600C to the hold, transfer, and
conf keys on your Host Telephone, you should be able to perform the
operations in the normal manner. The mute key is a function of the
Handset.
Placing a Call On Hold
1. Press the hold key on the
Handset during the call. You’ll
hear a “beep” and see:
HOLD
talk
2. To return to the call holding, press the hold or talk key.
Transferring a Call
1. Press the xfer key on the
Handset during the call. You’ll
hear a “beep” and see:
TRANSFER
talk
2. Dial the number of the
extension to which you are
transferring the call.
3410
talk
3. Press the talk key on the Handset before or after that party
answers. This completes the transfer.
Setting up a Conference Call
1. To connect a second party to
a call in progress, press the
conf key on the Handset.
You’ll hear a “beep” and see:
30
CONFERENCE
talk bat low lock
msg
2. Dial the number of the
extension with which you are
setting up the conference.
3410
talk
3. When that party answers, press the conf key on the Handset
again. You are now connected with both parties (3 party
conference).
4. Repeat the same steps for four or more party conference calls.
Note:
If you now press the talk key to hang up, the other parties
should still be on the call with each other.
Muting a call
1. Press the mute key on the
Handset during the call. You’ll
will see the talk icon blinking:
talk
2. To turn mute off, press the mute key again and the call is
restored.
Lock Mode
Your MER 9600C phone can be locked so that no outgoing calls
can be made.
Locking
1. Press and Hold the chan key
for one second while in
standby. A code input display
appears:
2. Enter a 2 digit number.
Enter 2 digits
Lock code=--
Enter 2 digits
Lock code=78
3. Press the chan key once
again. The LCD displays
“Lock?”, asking if you want to
continue.
31
LOCK?
Lock code=78
4. Press the chan key once
again to confirm you’re entry.
You’ll see:
lock
Unlocking
1. Press and Hold the chan key
for one second while in
standby. A code input display
with the lock icon appears:
2. Enter the 2 digit number you
used to lock your phone with.
Enter 2 digits
Lock code=-lock
Enter 2 digits
Lock code=78
lock
3. Enter the 2 digit lock code
and press chan. If the
number you entered was
correct, you will hear a “beep”
and the LCD display will
clear. The phone will go into
Standby mode:
4. If the 2 digit number you enter
was incorrect, you will hear a
error tone when you press
chan. The LCD display will
clear but the lock icon will
remain on as the phone goes
into Standby mode:
Note:
lock
Repeat steps 1-3 if you still wish to unlock the keypad of your
telephone.
32
Your EXP9530 Headset
The optional EXP9530 Head Set provides a “Hands-Free” Option for
the MER 9600C. It is highly recommended that you use the
EXP9530 Head Set with the MER 9600C. With the Head Set
installed, you can use the Belt Clip to carry the Handset, and conduct
a conversation using the Head Set.
To install the optional Head Set
1. Open the cover over the
HEAD SET Jack
2. Plug the Head Set in. No other settings are needed.
Operation of the MER 9600C using the Head Set is exactly the
same as using the Handset. However, you will hear through the Head
Set earphone, and talk through the Head Set microphone. The
Handset earphone and microphone (mouthpiece) are disconnected.
33
Optional Backup Adapter
The Optional Backup Adapter provides protection against losing a call
in case of AC Power failure. The Backup Adapter contains a Battery
Pack that provides enough power for you to complete the call and
hang up.
To install the Backup Adapter:
1. Disconnect the Standard AC Adapter from the Base Unit of the
MER 9600C.
2. Plug the AC Adapter into the jack of the EXP9505.
3. Plug the wire from the EXP9505 into the DC IN jack of the
Base Unit.
To Base Unit
From AC
Adapter
Backup
AC Adapter
34
Accessories and Replacement Parts
For the following Optional Accessories and Replacement Parts
contact your PBX Administrator.
2 AC Adapters
AD9500/AD960
Telephone Cord
Belt Clip
EXP9602
Backup Adapter
EXP9505
500mAh Battery
BT-9000
Base Unit Wall Mount
EXP9660
Ope
Head Set
EXP9530
Charger and AC
Adapter EXP9685
Leather Case
EXP9683
35
ratin
R
g Gu
ide
Operating Guide
OMMER9600
Troubleshooting
If your MER 9600C Cordless Telephone is not performing to your
expectations, please try these simple steps. If you are still unable to
resolve the problems, contact your PBX Administrator.
Note:
Do not attempt to service this unit yourself. All service must
be done by qualified service personnel.
Problem
Suggestion
•
Make
sure
the
AC Adapter is plugged
Charge 1 light won’t
into the Charge Unit and wall outlet.
come on when Handset
•
Make sure Handset is properly seated in
is placed in Charge
Charge Unit.
Unit.
• Make sure the Lead-Acid Battery Pack
is properly placed on the Handset.
• Make sure that the charging contacts on
the Handset and the Charge Unit are
clean.
•
Make sure the AC Adapter is plugged
Charge 2 light won’t
into the Charge Unit and wall outlet.
come on when Spare
•
Make sure Spare Battery is properly
Battery is placed in
seated in Charge Unit.
Charge Unit. (low
• Make sure that the charging contacts on
battery only)
the Spare Battery and the Charge Unit
are clean.
•
Make sure that the Base Unit antenna is
Conversation
fully vertical.
interrupted frequently.
• Move closer to the Base Unit.
• Check for LOW BAT warning.
• Move closer to the Base Unit.
Warning tone and
NO SERVICE message.
• Lead-Acid Battery may be weak. Charge
Handset doesn’t ring.
the Battery Pack for 8 hours.
• Make sure the Base Unit antenna is fully
vertical.
• The Handset may be too far away from
the Base Unit.
36
Specifications
General – The MER 9600C complies with FCC Parts 15 and 68.
Frequency Control
: Phase Lock Loop
Modulation
: FM
Operating Temperature
: −10° to +50° C
Base Unit
Receive/Transmit Frequency : 902 MHz to 928 MHz
Power Requirements
: 10V DC from supplied AC Adapter
Size
: 4 1/4 in. W X 7 1/2 in. D X 2 1/4 in. H
Weight
: Approx. 15.4 ounces
Handset
Receive/Transmit Frequency : 902 MHz to 928 MHz
Power Requirements
: Rechargeable sealed Lead Acid
Battery Pack
Size
: 2 1/4 in. W x 1 1/2 in. D x 8 1/2 in. H
(with antenna)
Weight
: Approx. 8.8 ounces with battery
Battery
: Capacity 500 mAh, 4.0V
Talk Mode
: 5 hours (typical)
Standby Mode
: 40 hours (typical)
Specifications shown are typical and subject to change without notice.
37
®
MER 9600C
900 MHz Digital
PBX
Cordless Telephone
Operating Guide
PRECAUTIONS
Before you read anything else,
please observe the following:
WARNING!
Uniden America Corporation DOES NOT represent this unit to be
waterproof. To reduce the risk of fire, electrical shock, or damage to the unit,
DO NOT expose this unit to rain or moisture.
BATTERY WARNING
This equipment contains a Rechargeable sealed Lead-Acid
Battery.
Do not short circuit the battery.
Do not charge the Rechargeable sealed Lead-Acid Battery
used in this equipment in any charger other than the one
designed to charge this battery as specified in this Guide.
Using another charger may damage the battery, or cause
the battery to explode.
Base Unit Controls & Functions
Cordless Key
Desk Key
Power Indicator
Handset Controls & Functions
1
2
10
talk bat low lock
talk
msg
vol
chan
3
4
5
F1
hold
6
7
8
1
4 ghi
7pqrs
F2
xfer
F3
conf
2abc
5 jkl
8 tuv
0oper
11
12
13
14
F4
mute
3def
15
16
6mno
9wxyz
#
9
1.
2.
3.
4.
5.
6.
7.
8.
Ringer ON/OFF switch
Message Display
Talk (talk) key
F2 Function key
F1 Function key
Hold (hold) Button
Transfer (xfer) Button
Numeric Keypad
9.
10.
11.
12.
13.
14.
15.
16.
Microphone
Head Set Jack
Channel (chan) key
Volume (vol) key
F3 Function key
F4 Function key
Mute (mute) key
Conference (conf) key
One Year Limited Warranty
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the
original retail owner, this Uniden Product to be free from defects in
materials and craftsmanship with only the limitations or exclusions set out
below.
WARRANTY DURATION: This warranty to the original user shall
terminate and be of no further effect 12 months after the date of original
retail sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modified, altered, or used as
part of any conversion kits, subassemblies, or any configurations not sold
by Uniden, (C) improperly installed, (D) serviced or repaired by someone
other than an authorized Uniden service center for a defect or malfunction
covered by this warranty, (E) used in any conjunction with equipment or
parts or as part of any system not manufactured by Uniden, or (F)
installed or programmed by anyone other than as detailed by the
Operating Guide for this product.
STATEMENT OF REMEDY: In the event that the product does not
conform to this warranty at any time while this warranty is in effect,
warrantor will repair the defect and return it to you without charge for
parts, service, or any other cost (except shipping and handling) incurred
by warrantor or its representatives in connection with the performance of
this warranty. THE LIMITED WARRANTY SET FORTH ABOVE IS THE
SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT
AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF
ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR
ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED
TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT
COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some provinces do not
allow this exclusion or limitation of incidental or consequential damages
so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you
may also have other rights which vary from province to province. This
warranty is void outside Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If,
after following the instructions in this Operating Guide you are certain that
the Product is defective, pack the Product carefully (preferably in its
original packaging). Include evidence of original purchase and a note
describing the defect that has caused you to return it, The Product should
be shipped freight prepaid by traceable means, or delivered, to warrantor
at:
Lectron Radio Sales, Ltd.
644 The Queensway
Peterborough, ON. K9J 7H4 Canada
(705) 743-7000, 8 a.m. to 5 p.m. Central,
Monday through Friday
Covered under one or more of the following U.S. patents:
4,511,761 4,523,058 4,595,795, 4,597,104
4,797,9164,803,4915,157,686 5,253,268
and other patents pending.
®
©1997 Uniden America Corporation. All rights reserved.
Printed in the USA
OMMER9600C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising