Uniden | SX307-3C | Owner Manual | Uniden SX307-3C Owner Manual

Uniden SX307-3C Owner Manual
FRS
2-way
radios
SX307
• 22 FRS Channels
• Weather Channels
• 121 Privacy Codes
• Weather Alert
• Channel Scan
• 5 VOX levels
Congratulations on your purchase of a Uniden
SX307 series radio. This lightweight, palm-sized
radio is a state-of-the-art device, equipped with
many valuable features. Use it at sporting
events, to stay in contact with family and
friends, hiking, skiing, outdoors, or in a
neighborhood watch for vital communication.
• Channel Monitor
• 10 Call tones
PACKAGE CONTENTS
• Key Lock
• Roger Beep
• Beep Tone
• Battery Strength Meter
Each radio uses 3 AA rechargeable Ni MH
batteries, included.
• Backlight
• Battery Save/Low Battery
Alert
If your model number contains a "C," your
package contains a microUSB Y charging cable.
• Volume Setting
• Call Button
• Last Channel
Memory
• Up to 30-mile Range*
If your model number contains "CK," it contains
a charging kit (including a charging cradle).
• Auto Squelch
• Charging Kit (model names
with CK) or Y-Split micro
USB cable (model names
with C)
• microUSB Jack
• Earbud/Headphone Jack
* Range may vary depending on environmental and/or
topographical conditions.
3
1
8
2
9
4
5
10
11
12
6
7
13
1
Antenna
8
LCD
2
Push to Talk
9
CH/VOL Up
3
Headphone/microUSB jack
10
CH/VOL Down
4
WX/LOCK
11
CH/LIGHT
5
CALL/MON
12
Microphone
6
MENU/Power
13
Charging Contacts
7
Speaker
If your models number contains "HS," it contains
headsets.
Refer to the packaging for other specific
contents. .
INSTALL THE BATTERIES
Each radio uses 3 AA rechargeable NiMH
batteries (included).
1. If necessary, remove the belt clip. Press
up on the belt clip latch and slide the belt
clip off of the radio.
2. Remove the battery compartment door by
pressing on and sliding out the
compartment door. Remove the cover.
3. Install the 3 AA batteries into the battery
compartment. Be certain to follow the +
and – symbols in the compartment.
Installing the batteries incorrectly will
prevent the unit from operating.
4. Replace the battery compartment door by
sliding the door into place.
5. Replace the belt clip if necessary.
BATTERY
/
6. Replace
the belt clip LEVEL
if necessary.
LOW LEVEL ALERT
This unit has a battery level meter on the
display to indicate the status of the batteries.
When the battery in the unit is low, the battery
level meter icon
flashes and . Recharge
the batteries immediately.
CHARGING THE RADIO
For radios with microUSB Y-cable:
1. Plug one branch of the microUSB Y-Cable
into each radio's microUSB charge port.
2. Insert the other end (USB) into a USB
power source (computer, phone charger,
etc - not included).
3. Charge the batteries for 16 hours and
disconnect the radio from the Y-cable after
charging.
For radios with a charging cradle:
1. Connect the AC adapter to DC IN 9V jack
on the charger and to a standard 120V AC
wall outlet.
2. Set the charging cradle on the desk or
tabletop, and place the radio in the
charging cradle with the keypad facing
forward.
3. Make sure that the LED illuminates. Charge
the batteries for 16 hours and remove the
radio from the charging cradle after
charging.
Warning!
• Neither the radio nor the charging cradle are
waterproof.
• If the charging cradle falls into water, unplug it
before attempting to remove it from the water.
Allow the cradle to dry completely before
reconnecting the power.
• Wipe off dirt or shake water from your radio
before placing in the charging cradle if your
radio is soiled or wet.
Notes:
• Install the batteries before charging. Charge
time may vary depending on the battery life
remaining. For fastest charging, turn off the
radio before charging.
• If battery power is low, you cannot operate the
radio even using external power. Allow the
batteries to charge before using. If you try to
transmit while power is low, the radio will
automatically turn off.
USING THE RADIO
In order to get the most out of your new radio,
read this reference guide completely before
attempting to operate the radio.
TURNING THE RADIO ON AND ADJUSTING
THE VOLUME
1. Press and hold the MENU/
key to turn
the radio ON.
2. Press and hold the MENU/
key to turn
the radio OFF.
3. Press the ▲ or ▼ keys to increase or
decrease the volume level. L0 - L8 displays
as you press the keys.
USING THE MENUS
Press MENU/
key to enter the Menu system.
Each time you press MENU/
key you advance
through the system.
• Press MENU/
(0 - 121).
once; access Privacy Codes
• Press MENU/
twice; set the transmit (call)
tone for your radio (1 - 10, Off)
• Press MENU/
three times - access VOX.
(Levels 1 - 5, Off)
• Press MENU/
four times - exit Menus.
WORKING WITH CHANNELS / PRIVACY
CODES
Your radio has 22 channels and 121 Privacy
Codes you can use to talk to others. In order to
speak to someone, each of you must be set to
the same channel/Privacy Code.
1. With the radio on, press CH/LIGHT key
once. The current channel number flashes.
2. Use the ▲ or ▼ keys to select other
channels (1 - 22). Press and hold ▲ or ▼
keys to rapidly change channels.
3. Press CH/LIGHT key again to set the
selected channel.
4. Press MENU/
key once. The current
Privacy Code flashes.
5. Use the ▲ or ▼ keys to select other
Privacy Codes (1 - 121). Press and hold ▲
or ▼ keys to rapidly change Privacy
codes.
6. Press MENU/
key three times to set the
Privacy Code and exit the Menus.
VOICE OPERATED TRANSMISSIOS
Your radio is equipped with a user selectable
Voice Operated Transmitter (VOX) that can be
used for automatic voice transmissions. The
VOX feature is designed to be used with a
headset with a microphone. Transmission is
initiated by speaking into the headset's
microphone instead of pushing the PTT button.
To select the VOX level:
1. Enter the Menu. Advance through the
Menu until the vox icon appears on the
display. The current level (OFF, 1-5) will be
indicated. Level oF (OFF) disables VOX,
while levels 1-5 set the sensitivity of the
VOX circuit.
2. Press either the ▲ or ▼ keys to select the
desired VOX sensitivity level. Use level 1
for increased sensitivity to voice in normally
quiet environments, and use a higher level
to reduce undesired activation in very noisy
environments.
CHANNEL SCAN FEATURES
Your radio has a channel scan feature that
allows you to easily scan all 22 channels. When
an active channel is detected, the unit pauses on
that channel until the channel is clear. Then,
after a 2 second delay, the radio continues
scanning.
When the unit stops on an active channel, you
can press the PTT button on the microphone to
transmit on that channel.
To turn ON channel scan
Quickly press CH/LIGHT then hold ▼ for 3
seconds. The channels will cycle down
through all 22 chanels. To reverse scan
direction, press ▲. To stop scanning,
press MENU/ .
TALKING ON YOUR RADIO
1. Press and hold the PTT button and speak
in a clear, normal voice about 2-3 inches
away from the microphone. (While you are
transmitting, the tx icon displays. To avoid
cutting off the first part of your
transmission, pause slightly after pressing
the PTT button before you start talking.)
2. When you are finished speaking, release
the PTT button. You can now receive
incoming calls. While receiving, the rx icon
displays.
KEY LOCK
1. To lock the keypad, press and hold WX
LOCK key. The icon appears on the
display.
2. To unlock the keypad, press and hold WX
LOCK key again. The icon disappears
from the display.
Note: While keylock is on, you can still use the
radio to receive, transmit, use call, turn volume
up or down, MON and MENU/
to turn the
radio on or off.
BACKLIGHT
Press and hold CH/LIGHT. A red backlight turns
on. It automatically turns off after several
seconds
TRANSMITTING A CALL ALERT TONE
Your radio is equipped with a call tone that will
be transmitted when the CALL/MON key is
pressed.
To transmit the call tone, press the CALL/MON
key. The tone will be transmitted.
AUTO SQUELCH
The radio is equipped with an automatic squelch
system which shuts off weak transmissions and
unwanted noise due to terrain conditions or
range limitations.
MONITOR MODE
Your radio allows you to listen for weak signals
on the current channel at the press of a key.
To turn ON monitor mode, Press and hold
CALL/MON for 2 seconds. The tx icon
displays. On a channel that does not have
activity, you will hear only an open-squelch
hissing noise.
To turn OFF monitor mode, press and hold the
CALL/MON key for 2 seconds again.
SPECIFICATIONS
Channels
143 (22 Channels + 121 Privacy
Codes)
Operating
Frequency
UHF 462.5500 - 467.7125 MHz
(GMRS/FRS)
162.4000 - 162.5500 MHz (WX)
Power
Source
3 rechargeable NiMH batteries
per radio
Battery
Life
12 hours typical (5/5/90 duty
cycle)
Frequency Chart
CH
DCS Code List
Freq.[MHz] Cross Ref.
CH
1
462.5625 - FRS &
GMRS 1
12
467.6625 - FRS
12
2
462.5875 - FRS &
GMRS 2
13
467.6875 - FRS
13
3
462.6125 - FRS &
GMRS 3
14
467.7125 - FRS
14
4
462.6375 - FRS &
GMRS 4
15
462.5500 - GMRS
11
5
462.6625 - FRS &
GMRS 5
16
462.5750 GMRS 8
6
462.6875- FRS &
GMRS 6
17
462.6000 - GMRS
12
462.7125 - FRS &
GMRS 7
18
7
Freq.[MHz] Cross Ref.
462.6250 GMRS 9
8
467.5625 - FRS 8
19
462.6500 - GMRS
13
9
467.5875 - FRS 9
20
462.6750 - GMRS
10
10
467.6125 - FRS
10
21
462.7000 - GMRS
14
11
467.6375 - FRS
11
22
462.7250 - GMRS
15
Note: This product is considered FRS only with 22 FRS
channels in the US market. It is considered a
GMRS product in the Canadian market.
CTCSS Chart (Hz)
Code
oF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Freq.
OFF
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
Code
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Freq.
131.8
136.5
141.3
146.2
151.4
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
Tone
No.
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
Octal
Code
023
025
026
031
032
043
047
051
054
065
071
072
073
074
114
115
116
125
131
132
134
143
152
155
156
162
165
172
174
205
223
226
243
244
245
251
261
263
MAINTENANCE
Tone
No.
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
Octal
Code
265
271
306
311
315
331
343
346
351
364
365
371
411
412
413
423
431
432
445
464
465
466
503
506
516
532
546
565
606
612
624
627
631
632
654
662
664
703
Tone
No.
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
Octal
Code
712
723
731
732
734
743
754
036
053
122
145
212
225
246
252
255
266
274
325
332
356
446
452
454
455
462
523
526
RBRC Information
As part of our commitment to protect the
environment and conserve natural
resources, Uniden voluntarily participates
in an RBRC® industry program to collect
and recycle used Ni-MH batteries within the US.
Please call 1-800-8-BATTERY for information on
Ni-MH battery recycling in your area. (RBRC® is a
registered trademark of the Rechargeable Battery
Recycling Corporation.)
To be safe and sure:
• Never open your radio’s case.
• Never change or replace anything in your radio
except the batteries.
Your radio might cause TV or radio interference even
when it is operating properly. To determine whether
your radio is causing the interference, turn it off. If the
interference goes away, your radio is causing it. Try to
eliminate the interference by moving your radio away
from the receiver. If you cannot eliminate the
interference, the FCC requires that you stop using the
radio.
Do not use the radio with a damaged antenna. If a damaged
antenna comes into contact with the skin, a minor burn may result.
Please contact your local dealer for a replacement antenna.
Body-Worn Operation
This device was tested for typical body-worn operations using the
supplied belt-clip.
To maintain compliance with FCC RF exposure requirements,
body-worn operations are restricted to the supplied belt-clip.
For hand-held operation, the radio should be held 1 inch from the
user's face. The use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure requirements
and should be avoided.
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original
retail owner, this Uniden Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and
be of no further effect 12 months after the date of original retail sale. The
warranty is invalid if the Product is: (A) damaged or not maintained as
reasonable or necessary, (B) modified, altered, or used as part of any
conversion kits, sub-assemblies, or any configurations not sold by Uniden, (C)
improperly installed, (D) serviced or repaired by someone other than an
authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of any
system not manufactured by Uniden, or (F) installed or programmed by anyone
other than as detailed by the owner’s manual for this product.
Do not operate the radio in hazardous environments.
Explosion or fire may result. Do not operate the radio
near unshielded electrical blasting caps.
FCC ID: AMWSX237
Under certain conditions, radios can interfere with
blasting operations and may cause an explosion. Turn
your radio OFF to prevent accidental transmission
when in a blasting area or in areas posted: "Turn off
two-way radio." Construction crews often use remote
control RF devices to set off explosives.
FCC PART 15 COMPLIANCE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
STATEMENT OF REMEDY: In the event that the product does not conform to
this warranty at any time while this warranty is in effect, warrantor will either, at
its option, repair or replace the defective unit and return it to you without charge
for parts, service, or any other cost (except shipping and handling) incurred by
warrantor or its representatives in connection with the performance of this
warranty. Warrantor, at its option, may replace the unit with a new or refurbished
unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER,
WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT
OVERPAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some
states do not allow this exclusion or limitation of incidental or consequential
damages so the above limitation or exclusion may not apply to you.
Care and Safety
Changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the
equipment.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state. This warranty is void
outside the United States of America and Canada.
Avis de conformité à la FCC : Ce dispositif a été testé et s’avère
conforme à l’article 15 des règlements de la Commission fédérale
des communications (FCC). Ce dispositif est soumis aux conditions
suivantes: 1) Ce dispositif ne doit pas causer d’interférences
nuisibles et; 2) Il doit pouvoir supporter les parasites qu’il reçoit,
incluant les parasites pouvant nuire à son fonctionnement.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after
following the instructions in the owner’s manual you are certain that the Product
is defective, pack the Product carefully (preferably in its original packaging). The
Product should include all parts and accessories originally packaged with the
Product. Include evidence of original purchase and a note describing the defect
that has caused you to return it.The Product should be shipped freight prepaid,
by traceable means, to warrantor:
Hazardous Environments
To clean the radio, use a soft cloth dampened with
water. Do not use cleaners or solvents because they
can harm the body of the unit and leak inside, causing
permanent damage. Use a dry, lint-free cloth to clean
the battery contacts. Do not submerge the unit in
water. If the unit gets wet, turn it off and remove the
batteries immediately.
Dry the battery compartment with a soft cloth to
minimize potential water damage. Leave the battery
compartment cover off overnight to ensure complete
drying. Do not use the radio until the unit is completely
dry.
WARNING! Read this information before using the
radio. In August 1996 the Federal Communications
Commission (FCC) of the United States with its action
in Report and Order FCC 96-326 adopted an updated
safety standard for human exposure to radio frequency
electromagnetic energy emitted by FCC regulated
transmitters.
Those guidelines are consistent with the safety
standard previously set by both U.S. and international
standards bodies. The design of the radio complies
with the FCC guidelines and these international
standards.
Never allow children to operate the radio without adult
supervision and the knowledge of the following
guidelines.
FCC RF EXPOSURE INFORMATION
WARNING! It is up to the user to properly operate this radio
transmitter to insure safe operation. Please adhere to the
following:
Use only the supplied or an approved antenna. Unauthorized
antennas, modifications, or attachments could impair call
quality, damage the radio, or result in violation of FCC
regulations.
For more information about RF exposure, please visit the FCC web
site at www.fcc.gov.
FCC PART 15 / IC COMPLIANCE
IC: 513C-SX307
Tout changement ou modification non approuvé expressément par
la partie responsable pourrait annuler le droit à l’utilisateur de faire
fonctionner cet équipement.
IC COMPLIANCE
Uniden America Corporation
C/O Saddle Creek
743 Henrietta Creek Road, Suite 100
Roanoke, TX 76262
This device complies with Industry Canada license-exempt RSS
standard(s).Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
Changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the
equipment.
Cet appareil est conforme aux normes RSS exemptes de licences
d’Industrie Canada. Son fonctionnement est soumis aux deux
conditions suivantes :
1. Cet appareil ne doit pas causer d’interférences nuisibles et
2. Cet appareil doit accepter toute interférence, y compris les
interférences susceptibles de provoquer un fonctionnement
non désiré de l'appareil.
Tout changement ou modification non approuvé expressément par
la partie responsable pourrait annuler le droit à l’utilisateur de faire
fonctionner cet équipement.
ONE YEAR LIMITED WARRANTY
Important: Evidence of original purchase is required for warranty
service.
WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden")
© 2019 Uniden America Corporation
All rights reserved
Issue 3, June 2019
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising