Uniden | 2MB-3.6 | Installation guide | Uniden 2MB-3.6 Installation Guide

Uniden 2MB-3.6 Installation Guide
ProSeries
IP CAMERA
INSTALLATION GUIDE
4KTPD-MVF
4MTPD-MVF
4MTPD-2.8
2MTPD-VF
4MMD-2.8
2MMD-2.8
4MED-3.6
2MED-3.6
© 2018 Uniden America Corporation
Irving, Texas
2MTD-2.8
4KB-MVF
4MB-MVF
2MB-VF
4MB-3.6
2MB-3.6
Issue 2, June 2018
Uniden surveillance products are not manufactured and/or sold with the intent to be used for illegal
purposes. Uniden expects consumer’s use of these products to be in compliance with all local,
state, and federal law. For further information on video surveillance and audio recording legal
requirements, please consult your local, state and federal officials.
Uniden constantly works on improving our products. This includes updating our documentation
with the latest firmware changes. Go to www.uniden.com to find the latest version of all
documentation.
© 2018 Uniden America Corporation
All rights reserved.
CONTENTS
OVERVIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
WHAT’S INCLUDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
INSTALL CAMERAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
INSTALLATION TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
TAMPER-PROOF DOMED CAMERAS. . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INSTALL MINI DOME CAMERA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
What’s Included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Install Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
INSTALL EYEBALL DOME CAMERA . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
What’s Included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Install Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INSTALL TURRET DOME CAMERA . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
What’s Included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Install Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
INSTALL LARGE BULLET CAMERAS. . . . . . . . . . . . . . . . . . . . . . . . . . 11
What’s Included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Install Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INSTALL SMALL BULLET CAMERAS. . . . . . . . . . . . . . . . . . . . . . . . . . 12
What’s Included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Install Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CONNECTING THROUGH PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
USING DEVICEMANAGER TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
WEB ACCESS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Set Security Levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
UNIDEN PROSERIES MOBILEPHONE CLIENT. . . . . . . . . . . . . . . . . 16
SOFTWARE OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Add device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TAMPER-PROOF DOME CAMERAS. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MINI AND EYEBALL DOME CAMERAS. . . . . . . . . . . . . . . . . . . . . . . . . 19
3
TURRET DOME AND LARGE BULLET CAMERAS. . . . . . . . . . . . . . . . 20
SMALL BULLET CAMERAS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
FCC PART 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
THREE-YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . 23
4
INSTALLATION
OVERVIEW
Uniden’s IP cameras can be installed indoors in either Uniden’s NVR or XVR surveillance systems.
TAMPERPROOF DOME
4KTPD-MVF
4MTPD-MVF
4MTPD-2.8
2MTPD-VF
MINI DOME
4MMD-2.8
2MMD-2.8
EYEBALL
DOME
4MED-3.6
2MED-3.6
TURRET
DOME
2MTD-2.8
LARGE
BULLET
4KB-MVF
4MB-MVF
2MB-VF
SMALL
BULLET
4MB-3.6
2MB-3.6
WHAT’S INCLUDED
•
•
•
•
•
IP camera
Mounting template sticker
Star-tipped Allen wrench
2-wire to 2.1mm barrell plug for optional 12V DC power input
Installation screws and anchors
Network cable and power source are not included. SD cards are not included. If you
plan on using the Automatic Network Restoration feature in the NVR, you will need to
purchase an SD card.
INSTALL CAMERAS
INSTALLATION TIPS
• When selecting an outside location for your cameras, keep in mind that most cameras
are designed to operate between 14°F to 122°F (-10°C to 50°C) with a relative humidity
of up to 95%. Avoid installing cameras in direct sunlight, and consider wind chill and other
environmental factors, too.
• Mount the camera in an area that is visible, but out of reach. Route the wiring so it does not
interfere with power or telephone/cable lines and it should not be where it could be easily cut.
Create a plan for camera wire routing and for camera angle.
• Adjust the camera angle so that it covers an area with high traffic as needed. In “highrisk” locations, have more than one camera cover the same area. This provides camera
redundancy if a vandal attempts to damage a camera.
• If you position cameras indoors, avoid pointing the camera at a glass window to see outside.
This may result in a bright white ring in the night vision image because the light from the night
vision LEDs may reflect off the window glass.
Take the following placement suggestions under consideration:
5
• Cabling Distance From NVR to Camera. The video signal sent from the camera to the DVR
is reduced over distance. The maximum distance allowed is 330 feet (100 meters). A 60 foot
cable is included. If you need a cable longer than 60 feet, then use an RG59 cable (with
suitable connectors).
• Do not submerge any camera.
• Mounting. Ensure the camera is mounted on a stable surface which is capable of supporting 5
times the weight of the camera.
• Avoid direct exposure to the weather. Cameras which are weatherproof may be mounted
outside, such as under an eave or other overhang; however, the image will be affected by rain,
etc., landing on the lens. Do not allow direct sunlight to land on the lens.
1. With the DVR connected to the camera, hold it in the location where you want it mounted.
Check the display on the monitor to verify that the view from that location is acceptable.
2. Mount the camera(s) to the desired surface using the parts in the supplied mounting kit. If
mounting on drywall, use the drywall anchors supplied in the kit.
3. Adjust the camera to ensure that the camera has a satisfactory view of the area you would
like to monitor. Cameras have several adjustment points to provide maximum flexibility when
setting the view angle.
TAMPER-PROOF DOMED CAMERAS
1. Remove the camera and accessory items from the box. Verify that all parts are there.
2. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as
indicated on the sticker and install anchors and screws.
3. Unscrew the camera from the housing, allowing the camera to
separate from the housing and clear dome.
4. Connect the camera’s network cable tail to the house cabling through the 1” hole.
6
5. If you have a 4K TPD camera, connect the plugs from the
network cable tail to their appropriate cables.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
2.1mm Barrel Adapter
Red - Audio In
NOTE: 12VDC power supply
not included
White - Audio Out
Yellow - Video (BNC)
Red - 12VDC (optional)
RJ45
PoE
Red - Alarm Out
Black - Alarm In
Network
Activity
LEDs
6. Align the camera base screw holes to the screws. Hang the
base onto the screws then slide the base along the screw lock
to secure.
Screw Hole
and Lock
7. Remove the protective films from the inside and outside of the camera dome and clean the
dome with a microfiber cloth (not included) if available.
Do not use a paper towel to clean the camera lens or dome as it might leave
scratches.
8. Adjust the bracket to swivel the camera up to 175˚ on a
horizontal axis (orients the camera for top/bottom of frame).
Swivel
Direction
Swivel
Direction
Bracket
9. Loosen screw 1 and adjust the camera from 15 - 90˚ on a
vertical axis.
Screw 1
15˚ - 90˚
10.Loosen screw 2 to fine-tune the horizontal axis (+/- 30˚).
As you adjust the camera position, check it through the
NVR Preview screen.
Screw 2
11. Insert an SD card if needed.
Reset Button
SD Card Slot
7
12.Remove the dessicant packet from the sealed plastic envelope
and position it inside the camera.
13.Screw the housing back onto the camera base.
INSTALL MINI DOME CAMERA
What’s Included
•
•
•
•
•
•
IP camera
Mounting template sticker
Star-tipped Allen wrench
2-wire to 2.1mm barrell plug for optional 12V DC power input
Installation screws and anchors
Dessicant package
Install Camera
1. Remove the camera and accessory items from the box. Verify that all parts are there.
2. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as
indicated on the sticker and install anchors and screws.
3. Unscrew the camera from the housing, allowing the camera to
separate from the housing and clear dome.
4. Connect the camera’s network cable tail to the house cabling
through the 1” hole.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
Red - 12VDC (optional)
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
PoE
RJ45
5. Align the camera base screw holes to the screws. Hang the
base onto the screws then slide the base along the screw lock
to secure.
Screw Hole
and Lock
6. Remove the protective films from the inside and outside of the camera dome and clean the
dome with a microfiber cloth (not included) if available.
Do not use a paper towel to clean the camera lens or dome as it might leave
scratches.
8
Adjustable
collar
7. Adjust the collar to swivel the camera up to 175˚ on a horizontal
axis (orients the camera for top/bottom of frame).
As you adjust the camera position, check it through the
NVR Preview screen.
Thumb
Control
8. Insert an SD card if needed.
Reset Button
SD Card Slot
9. Remove the dessicant packet from the sealed plastic envelope
and position it inside the camera.
10.Align the tab on the housing with the slot on the camera base
for easier reassembly. Tighten screws.
INSTALL EYEBALL DOME CAMERA
What’s Included
•
•
•
•
•
•
IP camera
Mounting template sticker
Star-tipped Allen wrench
2-wire to 2.1mm barrell plug for optional 12V DC power input
Installation screws and anchors
Dessicant package
Install Camera
1. Remove the camera and installation items from the box. Verify that all parts are there.
Base
2. Hold the camera and sleeve steady and unscrew the ring from
the base.
Ring
Sleeve
Camera
3. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as
indicated on the sticker. Install the anchors.
4. Position the base on the template, aligning the screw holes to the anchors, and screw it into
position.
9
5. Connect the network cable tail to the house cabling through the
1” hole.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
Red - 12VDC (optional)
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
PoE
RJ45
6. Unscrew the hatch on the camera to insert an SD card if
needed.
7. Remove the dessicant packet from the sealed plastic envelope
and position it inside the camera.
8. Reassemble the camera, sleeve, and ring. Position the assembly onto the base and adjust
the camera to the correct viewing angle.
As you adjust the camera position, check it through the NVR Preview screen.
9. When the viewing angle is correct, tighten the ring to the base.
As you tighten the ring, keep adjusting the camera as needed.
INSTALL TURRET DOME CAMERA
What’s Included
•
•
•
•
•
•
IP camera
Mounting template sticker
Star-tipped Allen wrench
2-wire to 2.1mm barrell plug for optional 12V DC power input
Installation screws and anchors
Dessicant package
Install Camera
1. Remove the camera and installation items from the box. Verify that all parts are there.
10
Base
2. Hold the camera and sleeve steady and unscrew the ring from
the base.
Ring
Sleeve
Camera
3. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as
indicated on the sticker. Install the anchors.
4. Position the base on the template, aligning the screw holes to the anchors, and screw it into
position.
5. Connect the network cable tail to the house cabling through the
1” hole.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
Red - 12VDC (optional)
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
PoE
RJ45
6. Reassemble the camera unit. Remove the dessicant packet from the sealed plastic envelope
and position it inside the camera unit.
7. Screw the camera unit to the base securely enough to adjust
the camera position. Double check the position through the
NVR Preview screen.
Set Screw
Location (x2)
Use an oil-free soft brush or blow gently into the camera
dome to clear any dust or dirt.
8. Tighten the ring to the base. Insert the set screws to lock the camera into position.
INSTALL LARGE BULLET CAMERAS
What’s Included
•
•
•
•
•
•
IP camera
Mounting template sticker
Camera-specific Allen wrench
2-wire to 2.1mm barrell plug for optional 12V DC power input
Installation screws and anchors
Dessicant package
11
• Rubber plug (grommet) to seal network cable hole
Install Camera
1. Remove the camera and installation items from the box. Verify that all parts are there.
2. Position the installation template at the location (wall, ceiling, etc). Drill a 1” hole as indicated
on the sticker and install the anchors provided.
3. If your bullet camera is equipped with an SD slot, insert an
SD card now before you install the camera. Unscrew the
rectangular hinged panel and insert the SD card.
SD Card Slot
Reset Button
2.1mm Barrel Adapter
Red - Audio In
NOTE: 12VDC power supply
not included
4. Thread the network cable tail through the grommet and connect
it to the house cabling through the 1” hole. Plug the grommet
into the hole. Using the screws provided, screw the camera
base into position.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
White - Audio Out
Yellow - Video (BNC)
Red - 12VDC (optional)
RJ45
PoE
Red - Alarm Out
Black - Alarm In
Network
Activity
LEDs
4KB-MVF
Red - 12VDC (optional)
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
PoE
RJ45
4MB-MVF, 2MB-VF
5. Loosen screw 1 to rotate the camera and stand up to 360°.
Loosen screw 2 to adjust the camera body up to 90° and screw
3 to fine tune the camera position up to 90°. Loosen Screw 4 to
adjust the sun shade.Check the camera’s position through the
NVR Preview screen as you adjust the camera.
Screw 1
Screw 3
Screw 2
12
Screw 4
6. Unscrew the access cover and swing it open. Unscrew the
adjustment levers just enough to move them and adjust the
image. Check the camera view through the NVR Preview
screen.
• Zoom - Move lever to the left for Telephoto (zoom in) and to the
right for Fish-Eye (zoom out).
• Focus - Move lever to left and right to adjust focus.
7. Tighten the adjustment lever screws when complete and close
the compartment.
Cover
Focus
Zoom
INSTALL SMALL BULLET CAMERAS
What’s Included
•
•
•
•
•
•
•
IP camera
Mounting template sticker
Camera-specific Allen wrench
2-wire to 2.1mm barrell plug for optional 12V DC power input
Installation screws and anchors
Dessicant package
Rubber plug (grommet) to seal network cable hole
Install Camera
1. Remove the camera and installation items from the box. Verify that all parts are there.
2. Position the installation template at the location (wall, ceiling, etc). Drill a 1” hole as indicated
on the sticker and install the anchors provided.
3. Thread the network cable tail through the grommet and connect
it to the house cabling through the 1” hole. Plug the grommet
into the hole. Using the screws provided, screw the camera
base into position.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
4. Loosen screw 1 to rotate the camera and stand up to 360°.
Loosen screw 2 to adjust the camera body up to 90° and
screw 3 to fine tune the camera position up to 90°. Check the
camera’s position through the NVR Preview screen as you
adjust the camera.
Red - 12VDC (optional)
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
PoE
RJ45
Screw 1
Screw 2
Screw 3
5. Once positioned, tighten all screws to secure.
13
CONNECTING THROUGH PC
Running the DeviceManager tool on your PC lets you easily identify cameras’ IP addresses,
Subnet Masks, and Gateways. Use this information to view and configure cameras through the
browser.
From Internet Explorer, go to support.uniden.com/pro-support and select VMS & CMS. From the
Video Management System screen, select Download VMS to download the plugin.
USING DEVICEMANAGER TOOL
1. Open DeviceManager. The main Device Manager screen displays.
2. Check IPC, then select Discover. A list of IP cameras on the network displays.
DeviceManager - IP Search Option
DeviceManager - IP Cameras Discovered
NOTE: This tool can also modify IP addresses when setting a network camera IP
address with the device IP address and computer IP address in the same net.
14
WEB ACCESS
1. Input the network camera IP address in the browser address bar to log in. A pop-up browser
control installation message automatically displays. Click to download and install. The following
description uses Internet Explorer as example.
Network camera factory initial information is:
. . . IP address: 192.168.1.188
. . . http port: 80
. . . Manage user: admin
Install Plugins
No Plugins
2. After installing the plugins, input the network camera IP address again; a login popup prompts
you to set the password.
NOTE: In order to improve network security, the network camera password needs to be
8 - 16 alphanumeric characters.
NOTE: Entering an incorrect password 3 times locks the camera for about 30 seconds.
Set Password Request
Setting Password
3. After setting the password, enter the login interface. Input the network camera user name and
password to log into the system.
Login Interface
NOTE: If you have modified the initial IP address, please use the modified IP address to
log into the network camera.
15
Set Security Levels
NOTE: After installing the controls, if the pop-up login interface always reminds you
to download and install the Activex control, try upgrading your IE browser to IE11 and
reducing the IE security level.
1. Open the IE browser and select Tools/Internet Options/Security/Customized Level. Set the
security level to Medium High (default) or Medium Low.
2. Select Tools/Internet Options/Security/Customized level.
•
•
•
•
•
•
3.
Enable ActiveX controls and plugins.
Enable the marked as safe ActiveX-controlled execution scripts.
Initialize and execute the unmarked as safe ActiveX-controlled execution scripts.
Download unsigned ActiveX controls.
Download the signed ActiveX controls.
Run ActiveX controls and plugins.
When entering into the network camera main interface, you can click
on the top right corner
to exit system safely.
4. On the network camera main interface, you can operate real-time preview, video playback,
parameter configuration, file management, and log search.
NOTE: This fully functional interface is displayed when SD card is inserted into the
device. If no SD card is inserted, a simple interface of the device includes real-time
preview, parameter configuration, file management, and log search (except the video
playback).
NOTE: Under no plugins mode, insert an SD card to display fully functional interface.
NOTE :When the device is motorized lens, zoom
is to adjust length of the
focal length, focus
is to adjust the image resolution, iris
is to adjust the size of
the iris.
NOTE: If there are no image or interface displays issues after login, firstly clear the
cache, unload controls, then install the new controls unload controls: close IE, enter
Windows system contents, find the installation content (the default content is C: \
Program Files \ webactivex - rtsp or C: \ Program Files (x86) \ webactivex - rtsp) the
related controls information in the folder, run unins000. Exe files, the system will
automatically delete.
UNIDEN PROSERIES MOBILEPHONE CLIENT
SOFTWARE OPERATING
1. After install successfully, click software icon
on the mobile phone, then the software will be
running and start procedure to enter into login interface.
16
FUNCTIONS
Remove Login
Remember Password
Password modification
Local Login
User Register
User Name
DESCRIPTION
Account login, device information can store in the
cloud storage.
The app remembers the current account password.
Modifies the registered user password.
Can directly login without account; device stores the
information in the phone.
The account is used for storing customer information
and related device list in the cloud storage.
User Name
1. Log in with a registered user name/password. Enter the Device List management interface.
17
ICON
FUNCTION INTRODUCTION
Return to main menu.
Add device.
Device; click to play all channels.
Add device
1. Click Add icon
in the upper right corner to display the Add Device interface.
2. Manually add a device’s connection parameters; select the Search button to search and add
devices in the LAN.
Add Device
Contact List
• Connection mode: There are two methods to create serial number and IP/Domain direct
connections. The cloud method connects a device via serial number; the IP/Domain method is to
connect device via traditional IP address or dynamic domain name and port. Adopt serial number
to add device for default; click upper IP/Domain to switch IP/Domain method .
Note: When selecting IP/Domain mode to add device, if it fills the intranet IP address in
the IP item eg: begin with192.168.*.*, it can only connect the preview in LAN, it will fail
18
to connect the preview while using the outer net. Need to connect monitor through the
network,and must use the serial number or domain name to add device)
• Name: The monitoring device name. This user-created identifier identifes a device’s location and
according to the place name. It displays under the device icon and shows on the title during video
playback.
• Serial number: Device cloud connects to the only serial number, which can be obtained via
searching the LAN. Click the QR code icon
on the right side to scan the network’s input QR
code in the Web client display. The device directly scans Query Device ID QR code when using
Uniden’s mobile phone client.
• User name: The user name of front-end device; default = admin.
• Password: Password of front-end matches with its user name; default = blank.
3. After completing settings, click Confirm. The system automatically pre-connects to check
whether device information validity. If it is correct, it automatically returns to the Device list. If
incorrect, it will display an error message that you have to confirm and add again.
SPECIFICATIONS
TAMPER-PROOF DOME CAMERAS
4KTPD-MVF
GENERAL
IR Distance
Protection Grade
Power
Power Jack
Power
Consumption
Operating Temp
4MTPD-MVF
4MTPD-2.8
100’ Night Vision (12 IR LEDs)
IPX0/IK10
IPX0/IK09
PoE/12VDC
(optional)
2.1mm Power Jack for optional 12VDC input
<9W
<8W
IPX0
-4°F~104°F
(-15.5°C~40°C)
0% - 90%
Operating Humidity
Dimensions (inch) 4.61 (L) x 4.61 (W) x 3.39 (H)
CAMERA
Sensor
1/2.5” 8MP
1/3” 4MP progressive
progressive scan scan CMOS
CMOS
Max. Resolution
3840 x 2160
Min. Illumination
Lens
0Lux/F1.4 (IR on)
3.0 - 10mm
2.8 - 12mm
motorized lens
motorized lens
Auto/Manual
(1/25~1/10000), FLK
Electronic Shutter
2MTPD-VF
2592 x 1520
2.8mm Fixed
1/2.9” SONY
2.07 MP
Progressive
scan Exmor
CMOS
1920 x 1080
2.8-12mm
Varifocal
19
R/N Ratio
Analog Video
Output
Output Model
4KTPD-MVF
-----
4MTPD-MVF
≥35db (AGC OFF)
/
/
4MTPD-2.8
2MTPD-VF
≥50db (AGC
OFF)
1CH 1.0Vp-p
complex video output
PAL/NTSC adjustable
MINI AND EYEBALL DOME CAMERAS
GENERAL
IR Distance
Protection Grade
Power
Power Jack
Power
Consumption
Operating Temp
4MMD-2.8
2MMD-2.8
4MED-3.6
2MED-3.6
(MINI DOME)
(MINI DOME)
(EYEBALL
DOME)
(EYEBALL
DOME)
30’ Night Vision
(6 IR LEDs)
100’ Night Vision 100’ Night
(2 IR array
Vision
LEDs)
(36x5 IR LEDs)
IPX0
IPX0
IPX0, IK10
PoE/12VDC
(optional)
2.1mm Power Jack for optional 12VDC input
<8W
<6W
<8W
-4°F~104°F
(-15.5°C~40°C
Operating Humidity
0% - 90%
Dimensions (inch) 4.61 (L) x 4.61 (W) 4.61 (L) x 4.61 (W) 4.72 (L) x 4.72
x 3.39 (H)
x 2.6 (H)
(W) x 3.87 (H)
CAMERA
Image Sensor
1/3” 4MP progressive scan CMOS
Effective Pixels
Max. Resolution
----1920 x 1080
Min. Illumination
Lens
Electronic Shutter
0Lux/F1.4 (IR on) Color: 0.5Lux/F1.4, B/W:0.2Lux/F1.4
2.8mm lens
3.6mm
Auto/Manual
(1/25~1/10000), FLK
≥35db (AGC OFF) ≥50db (AGC OFF) ≥35db (AGC
OFF)
1CH 1.0Vp-p
/
complex video output
R/N Ratio
Video Output
Output Model
20
2MP
1920 x 1080
PAL/NTSC adjustable
2592 x 1520
<7W
-14°F~104°F
(-15.5°C~40°C)
4.72 (L) x 4.72
(W) x 3.87 (H)
1/2.9” SONY
2.07 MP
Progressive
scan Exmor
CMOS
2MP
1920 x 1080
3.6mm ICR lens
≥50db (AGC
OFF)
1CH 1.0Vp-p
complex video
output
TURRET DOME AND LARGE BULLET CAMERAS
GENERAL
IR Distance
2MTD-2.8
4KB-MVF
4MB-MVF
2MB-VF
(TURRET DOME)
(LARGE BULLET)
(LARGE
BULLET)
(LARGE
BULLET)
30-50’ Night Vision
(1x Array IR LEDs)
131-165’ Night
130-165’ Night
130-165’ Night
Vision
Vision
Vision
(3xArray IR LEDs) (IR Array LEDs)
3xIR-III LEDs)
Protection Grade
/
IPX0
Power
PoE with optional 12VDC
Power Jack
2.1mm Power Jack for optional 12VDC input
Power
<6W
<10W
<9W
Consumption
Operating Temp
-14°F~104°F
-4°F~104°F
(-15.5°C~40°C)
(-15.5°C~40°C)
Operating
0% - 90%
Humidity
Dimensions
3.28 (L) x 3.28 (W) 10.24 (L) x
10.35 (L) x 3.66
(inch)
x 3.66 (H)
3.07 (W) x 3.66 (H)
(W) x 3.76 (H)
CAMERA
Image Sensor
1/2.9” SONY
1/2.5” 8MP
1/3” 4MP
1/2.9” SONY
2.07 MP
Progressive
progressive scan 2.07 MP
Progressive scan
scan CMOS
CMOS
Progressive
Exmor
scan Exmor
CMOS
CMOS
Effective Pixels
2MP
--------2MP
Max. Resolution
1920 x 1080
3840 x 2160
4MP (2592x1520) 1920 x 1080
Min. Illumination
0Lux/F1.4 (IR ON)
Color: 0.06Lux/
F1.4, B/W:
0.01Lux/F1.4
0Lux/F1.4 (IR on)
Color: 0.1Lux/
F1.4,
B/W: 0.5Lux/F1.4
0Lux/F1.4 (IR on)
Color: 0.5Lux/
F1.4,
B/W: 0.2Lux/F1.4
Lens
2.8mm
3.0-10mm
motorized lens
2.8-12mm
motorized lens
0Lux/F1.4 (IR
on)
Color: 0.06Lux/
F1.4, B/W:
0.01Lux/F1.4
2.8-12mm
varifocal lens
≥35db (AGC
OFF)
≥50db (AGC
OFF)
Electronic Shutter Auto/Manual
(1/25~1/10000), FLK
R/N Ratio
≥50db (AGC OFF)
Output Model
-----
PAL/NTSC adjustable
21
SMALL BULLET CAMERAS
GENERAL
IR Distance
Protection Grade
Power
Power Jack
Power
Consumption
Operating Temp
4MB-3.6
2MB-3.6
(SMALL BULLET)
SMALL BULLET
100’ Night Vision
(30 x Φ5 IR LEDs)
IPX0
PoE for optional 12VDC
2.1mm Power Jack for
optional 12VDC input
<6W
-4°F~104°F
(-15.5°C~40°C)
0% - 90%
Operating
Humidity
Dimensions (inch) 2.6 (L) x 6.56 (W)
x 2.6 (H)
CAMERA
Image Sensor
1/3” 4MP progressive
scan MOS
Max. Resolution
4MP (2592 x 1520)
Min. Illumination
0Lux/F1.4 (IR on)
Color: 0.5Lux/F1.4,
B/W:0.2Lux/F1.4
3.6mm
Auto/Manual
(1/25~1/10000), FLK
≥35db (AGC OFF)
PAL/NTSC adjustable
Lens
Electronic Shutter
R/N Ratio
Output Model
6.56 (L) x 2.6 (W)
x 2.6 (H) (compare to left)
1/2.9” SONY 2.07 MP
Progressive scan Exmor
CMOS
1920 x 1080
0Lux/F1.4 (IR ON)
Color: 0.06Lux/F1.4,
B/W: 0.01Lux/F1.4
≥50db (AGC OFF)
COMPLIANCE
FCC PART 15
The equipment has been tested and found to comply with the limits for a Class B device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver
22
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment. Any change or modification must be approved in
writing by Uniden.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Tout changement ou modification non approuvé expressément par la partie responsable pourrait
annuler le droit à l’utilisateur de faire fonctionner cet équipement. Tout changement ou modification
doit être approuvé par écrit par Uniden.
Avis de conformité à la FCC : Ce dispositif a été testé et s’avère conforme à l’article 15 des
règlements de la Commission fédérale des communications (FCC). Ce dispositif est soumis
aux conditions suivantes: 1) Ce dispositif ne doit pas causer d’interférences nuisibles et; 2)
Il doit pouvoir supporter les parasites qu’il reçoit, incluant les parasites pouvant nuire à son
fonctionnement.
In order to comply with FCC RF Exposure requirements, this device must be installed to provide at
least 7.9 in (20 cm) separation from the human body at all times.
IC
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux normes CNR d’Industrie Canada destinés aux appareils radio
exempts de licence. Son fonctionnement est soumis aux deux conditions suivantes :
1) Cet appareil ne doit pas causer d’interférences nuisibles et;
2) Il doit pouvoir accepter les interférences, incluant celles pouvant nuire à son fonctionnement
normal.
In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to
provide at least 7.9 in. (20 cm) separation from the human body at all times.
Afin de se conformer aux exigences d’exposition RF FCC/ISED, ce dispositif doit être installé pour
assurer une séparation d’au moins 20 cm du corps humain à tout moment.
THREE-YEAR LIMITED WARRANTY
Important: SAVE YOUR RECEIPT! Evidence of original purchase is required for warranty service.
WARRANTOR: Uniden America Corporation (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants,
for three years, to the original retail owner, this Uniden Product to be free from defects in materials &
craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate & be of no further effect 36
months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits,
subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired
23
by someone other than an authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured
by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s manual for this
product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time
while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit &
return it to you without charge for parts, service, or any other cost (except shipping & handling) incurred by
warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option,
may replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE & ENTIRE WARRANTY PERTAINING
TO THE PRODUCT & IS IN LIEU OF & EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states
do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or
exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, & you may also have other rights which
vary from state to state. This warranty is void outside the United States of America & Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in
the owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably
in its original packaging). The Product should include all parts & accessories originally packaged with the
Product. Include evidence of original purchase & a note describing the defect that has caused you to return
it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
C/O Saddle Creek
743 Henrietta Creek Rd., Suite 100
Roanoke, TX 76026
24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising