Sub-Zero | ID-24F | Design Guide | Sub-Zero BI-30U/S 30" Classic Over-and-Under Refrigerator/Freezer Design Guide

Sub-Zero BI-30U/S 30" Classic Over-and-Under Refrigerator/Freezer Design Guide
DESIGN GUIDE
REVISED 8 / 2019
TA B L E O F C O N T E N T S
3
C L A S S I C R E F R I G E R AT I O N
40
P R O R E F R I G E R AT I O N
48
D E S I G N E R R E F R I G E R AT I O N
58
WINE STORAGE
90
U N D E R C O U N T E R R E F R I G E R AT I O N
100
SUB-ZERO WARRANTIES
Features and specifications are subject to change at any
time without notice. Visit subzero.com/specs for the most
up-to-date information.
Throughout this guide, dimensions may vary by ± 1/8" (3).
Dimensions in parentheses are millimeters unless otherwise
specified.
C L A S S I C R E F R I G E R AT I O N
subzero.com | 3
C L AS S IC R EF R I GE RATION
Classic Refrigeration
For Classic refrigeration, Sub-Zero designers and engineers
took a fresh look at everything, inside and out. Exterior
refinements include redesigned grilles and lower-profile
hinges. Inside, new technology in food preservation makes
Classic refrigeration nothing short of revolutionary.
C L AS S IC MO DE L S
BI-36R
BI-36UFD(ID)
BI-36RG
BI-42UFD(ID)
BI-36F
BI-36S
4 | Sub-Zero Customer Care 800.222.7820
BI-30U
BI-42S(ID)
BI-30UG
BI-42SD
BI-36U(ID)
BI-48S(ID)
BI-36UG
BI-48 SD
C L AS S IC R EF R I GE RATION
Specifications
INTERIOR CAPACITY— CU FT
(L )
A L L R E F R I G E R AT O R / ALL FREE Z E R
BI-36R
BI-36RG
BI-36F
OV E R - A N D - U N D E R
BI-30U
BI-30UG
BI-36U(ID)
BI-36UG
BI-36UFD(ID)
BI-42UFD(ID)
SI D E - B Y- S I D E
BI-36S
BI-42S
BI-42SID
BI-42SD
BI-48S
BI-48SID
BI-48SD
REFR
FRZR
23.5 (665)
23.4 (663)
22.7 (643)
REFR
FRZR
13.2 (374)
13.1 (371)
16.4 (464)
16.3 (462)
15.7 (445)
17.9 (507)
4.2 (119)
4.2 (119)
5.3 (150)
5.3 (150)
5.3 (150)
6.3 (178)
REFR
FRZR
12.4 (351)
16.3 (462)
15.8 (447)
16.0 (453)
19.1 (541)
18.6 (527)
18.8 (532)
8.2 (232)
8.0 (227)
7.9 (224)
7.9 (224)
9.8 (278)
9.6 (272)
9.6 (272)
subzero.com | 5
C L AS S IC R EF R I GE RATION
Classic Design Options
F R AMED
O VER LAY
Choose framed custom door panels that contrast with
the stainless steel full-length handles and louvered grille
(shown). The framed application is an overlay model with
framed design features. Panel, grille, and handle options are
available.
Custom overlay door panels can be combined with unique
handle hardware for design flexibility. Shown with the pro
handle option to complement Wolf ranges. Customize with
panel, grille, and handle options.
Panels: Custom panels, stainless steel, or white enamel.
Grille: Classic louvered grille insert or solid custom panel
for 84" (standard), 83", or 88" overall unit height. Dual wide
grille for dual installations.
Panels: Custom panels or stainless steel.
Grille: Solid custom panel or pro louvered grille for 84"
(standard), 83", or 88" overall unit height. Dual wide grille for
dual installations.
Handles: Custom, tubular, or pro handles.
Handles: Full-length standard or extended handles.
Framed
6 | Sub-Zero Customer Care 800.222.7820
Overlay
C L AS S IC R EF R I GE RATION
Classic Design Options
F LUS H INS ET
S TA I N LES S S TEEL
The flush inset design option allows for flush door and
grille panels and custom handle hardware. Shown with the
tubular handle option to match Wolf built-in ovens. The flush
inset application is an overlay model with flush inset panels.
Customize with panel, grille, and handle options.
Stainless steel models require no customization. To complement the look of Wolf ranges, choose the pro handle option
(shown). Grille and handle options are available.
Panels: Custom panels or stainless steel.
Grille: Pro louvered grille for 84" (standard), 83", or 88"
overall unit height. Dual wide grille for dual installations.
Handles: Tubular or pro handles.
Grille: Solid custom panel or pro louvered grille for 84"
(standard), 83", or 88" overall unit height. Dual wide grille for
dual installations.
Handles: Custom, tubular, or pro handles.
Flush inset
Stainless steel
subzero.com | 7
C L AS S IC R EF R I GE RATION
Overall Dimensions
A L L R EF R IG ER ATOR / AL L FRE E Z E R
26 3/16" (665)
36" (914)
84"
(2134)
73 3/4"
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
23 7/8"
(606)
14 1/8"
(359)
37 1/4"
(946)
2 3/8" (60)
Model BI-36R, BI-36RG, BI-36F
8 | Sub-Zero Customer Care 800.222.7820
23 7/8" (606)
Overall dimensions are based on stainless steel models.
For flush inset applications, add 1/2" (13) to door clearance
dimensions.
C L AS S IC R EF R I GE RATION
Overall Dimensions
O VER -AND-UND E R
26 3/16" (665)
30" (762)
26 3/16" (665)
36" (914)
84"
84"
(2134)
(2134)
50 3/4"
50 3/4"
(1289)
(1289)
23"
23"
(584)
(584)
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
(606)
(606)
14 1/8"
12 1/8"
(308)
(600)
23 7/8" (606)
23 7/8"
23 7/8"
23 5/8"
4" (102)
(359)
311/4"
(796)
23 5/8"
(600)
37 1/4"
(946)
2 3/8" (60)
2 3/8" (60)
Model BI-30U, BI-30UG
Model BI-36U(ID), BI-36UG
subzero.com | 9
C L AS S IC R EF R I GE RATION
Overall Dimensions
O VER -AND-UND E R
26 3/16" (665)
36" (914)
26 3/16" (665)
42" (1067)
84"
84"
(2134)
(2134)
50 3/4"
50 3/4"
(1289)
(1289)
23"
23"
(584)
HEIGHT DIMENSIONS ± 1/2" (13)
(584)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
23 7/8"
4" (102)
23 7/8"
(606)
(606)
8"
9"
(203)
(229)
23 5/8"
191/2" 23 5/8"
(495)
(600)
(600)
221/4"
(565)
2 3/8" (60)
Model BI-36UFD(ID)
10 | Sub-Zero Customer Care 800.222.7820
2 3/8" (60)
Model BI-42UFD(ID)
23 7/8" (606)
C L AS S IC R EF R I GE RATION
Overall Dimensions
S I DE-B Y-S IDE
26 3/16" (665)
36" (914)
84"
84"
(2134)
(2134)
73 3/4"
73 3/4"
(1873)
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
26 3/16" (665)
42" (1067)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
4" (102)
23 7/8"
23 7/8"
(606)
(606)
7 1/4"
(184)
7 1/2"
(191)
8 3/4"
(222)
23 7/8" (606)
10 3/8"
(264)
26 1/4"
221/4"
(668)
(565)
2 3/8" (60)
2 3/8" (60)
Model BI-36S
Model BI-42S(ID), BI-42SD
subzero.com | 11
C L AS S IC R EF R I GE RATION
Overall Dimensions
S I DE-B Y-S IDE
26 3/16" (665)
48" (1219)
84"
(2134)
73 3/4"
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
23 7/8"
(606)
8 3/8"
(213)
11 5/8"
(295)
30"
(762)
2 3/8" (60)
Model BI-48S(ID), BI-48SD
12 | Sub-Zero Customer Care 800.222.7820
23 7/8" (606)
C L AS S IC R EF R I GE RATION
Specifications
SHIPPING WEIGHT
A L L R E F R I G E R AT O R / ALL FREE Z E R
BI-36R
BI-36RG
BI-36F
OV E R - A N D - U N D E R
BI-30U
BI-30UG
BI-36U(ID)
BI-36UG
BI-36UFD(ID)
BI-42UFD(ID)
SI D E - B Y- S I D E
BI-36S
BI-42S
BI-42SID
BI-42SD
BI-48S
BI-48SID
BI-48SD
L B (KG )
420 (191)
430 (195)
406 (184)
L B (KG )
462 (210)
476 (216)
515 (234)
529 (240)
529 (240)
582 (264)
L B (KG )
538 (244)
582 (264)
608 (276)
608 (276)
630 (286)
656 (298)
656 (298)
Shipping weights are based on stainless steel models.
subzero.com | 13
C L AS S IC R EF R I GE RATION
Opening Dimensions
S TANDAR D INS TAL L ATION
24" (610)
OPENING
DEPTH
3/4" (19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
TOP VIEW
W
FRAMELESS
CABINETRY
3/4" (19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
83 3/4"
W
(2127)
OPENING
HEIGHT
OPENING WIDTH
SIDE VIEW
FILLER
W
FRAMED
CABINETRY
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit.
OPENING WIDTH
W
30" Model
29 1/2" (749)
36" Model
35 1/2" (902)
42" Model
41 1/2" (1054)
48" Model
47 1/2"
14 | Sub-Zero Customer Care 800.222.7820
(1206)
If an 83" (2108) grille height is specified, the opening height
must be decreased by 7/8" (22). If an 88" (2235) grille height is
specified, the opening height must be increased by 4" (102).
If two units are installed side by side, refer to page 16 for
dual standard installations.
C L AS S IC R EF R I GE RATION
Opening Dimensions
F LUS H INS ET INSTAL L ATION
26 3/16"
(665)
FLUSH
INSET
DEPTH
5 11/16" 3 1/2"
2 3/16"
(56)
(89)
(145)
FINISHED
RETURN
FINISHED
CLEATS
TOP VIEW
CLEAT
3/4" (19)
TYPICAL
W
FRAMELESS
CABINETRY
11/4"
1/4"
(6)
(32)
5 11/16" 3 1/2"
(89)
(145)
FINISHED
RETURN
SIDE VIEW
84"
W
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
CLEAT
FILLER
3/4" (19)
TYPICAL
W
FRAMED
CABINETRY
FRONT VIEW
NOTE: 3 1/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit with 3/4" (19) panel.
FLUSH INSET WIDTH
30" Model
W
Flush inset is available for overlay models only.
32" (813)
Dimensions assume a 3/4" (19) panel thickness.
36" Model
38" (965)
42" Model
44" (1118)
48" Model
50" (1270)
If an 83" (2108) grille height is specified, the flush inset
height must be decreased by 7/8" (22). If an 88" (2235) grille
height is specified, the flush inset height must be increased
by 4" (102).
If two units are installed side by side, refer to page 17 for
dual flush inset installations.
subzero.com | 15
C L AS S IC R EF R I GE RATION
Opening Dimensions
D U AL S TANDARD INSTAL L ATION
24" (610)
OPENING
DEPTH
3/4" (19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
TOP VIEW
W
FRAMELESS
CABINETRY
3/4" (19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
83 3/4"
W
(2127)
OPENING
HEIGHT
OPENING WIDTH
SIDE VIEW
FILLER
W
FRAMED
CABINETRY
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit.
DUAL OPENING WIDTH
W
Two 30" Models
59 3/4" (1518)
30" and 36" Models
65 3/4" (1670)
Two 36" Models
71 3/4" (1822)
16 | Sub-Zero Customer Care 800.222.7820
A dual installation kit is required for this installation.
C L AS S IC R EF R I GE RATION
Opening Dimensions
D U AL F LUS H IN SE T INSTAL L ATION
26 3/16"
(665)
FLUSH
INSET
DEPTH
(56)
CLEAT
5 11/16" 3 1/2"
2 3/16"
3/4" (19)
(89)
(145)
FINISHED
RETURN
FINISHED
CLEATS
TOP VIEW
TYPICAL
W
FRAMELESS
CABINETRY
11/4"
1/4"
(6)
(32)
CLEAT
5 11/16" 3 1/2"
(89)
(145)
FINISHED
RETURN
84"
W
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
FILLER
3/4" (19)
TYPICAL
W
FRAMED
CABINETRY
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit with 3/4" (19) panel.
DUAL FLUSH INSET WIDTH
W
Two 30" Models
62 1/4" (1581)
30" and 36" Models
68 1/4"
Two 36" Models
74 1/4" (1886)
(1734)
Flush inset is available for overlay models only.
Dimensions assume a 3/4" (19) panel thickness. A dual installation kit is required for this installation.
subzero.com | 17
C L AS S IC R EF R I GE RATION
Electrical Requirements
Plumbing Requirements
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit servicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause
interruption of operation.
Locate the water supply line within the shaded area shown
in the illustration below. Connect the water supply line to the
house supply with an easily accessible shut-off valve. Do
not use self‑piercing valves. The water supply line must not
interfere with the installation of the anti-tip brackets.
Installation must comply with all applicable electrical codes.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
ELECTRICAL REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
Service
15 amp dedicated circuit
Receptacle
Installation must comply with all applicable plumbing codes.
3-prong grounding-type
PLUMBING REQUIREMENTS
1/4"
Water Supply
Pressure
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
7"
E
(178)
6"
(152)
75 1/2" (1918)
FROM FLOOR
RIGHT SIDE
OF OPENING
RIGHT SIDE
OF OPENING
18" (457)
6" (152)
Electrical supply location
3" (76)
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
Water supply location
18 | Sub-Zero Customer Care 800.222.7820
OD copper, braided stainless
steel, or PEX tubing
36" (914)
C L AS S IC R EF R I GE RATION
Custom Panels
For framed, overlay, and flush inset applications, custom
door panels must be provided. Handle hardware must also
be provided for overlay and flush inset applications. Refer
to Panel Requirements below and the charts on pages
22–27 for custom panel dimensions for your specific design
application.
IMPORTANT NOTE: Do not cover a glass door with a solid
panel.
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
BI-36R, BI-36RG, BI-36F
All Other Models
Grille Panel
PA N E L T H I C K N E S S
Framed
Overlay and Flush Inset
MA X
FR AM ED PAN ELS
The framed application is an overlay model with framed
design features. It is not a separate model.
If the custom panel is thinner than 1/4" (6), a filler material
must be added to achieve a proper fit. If the panel is thicker
than 1/4" (6), rout an edge around the panel or mount the
custom panel on a sheet of 1/4" (6) thick material and insert
into the channel. Refer to the illustrations below.
Routing, recessing, or optional extended handles may be
required for finger clearance. Refer to the full-scale template
on page 34.
When installing two units side by side, refer to page 16 for
dual standard installations.
75 lb (34 kg)
50 lb (23 kg)
13 lb (6 kg)
MIN
1/4"
5/8"
1/4" (6) TRIM REVEAL
(6)
(16)
1/4" (6) PANEL
DOOR
Panel 1/4" thick or less
1/4" (6) min
ROUT TO 1/4" (6)
DOOR
Panel thicker than 1/4"
subzero.com | 19
C L AS S IC R EF R I GE RATION
Custom Panels
PART IAL F R AME D OPTION
PAN EL M O U N TI N G K I T
The partial framed kit includes a stainless steel panel for
above and below the external dispenser. Refer to the chart
below for panel width. The kit is avail­able through an authorized Sub-Zero dealer. For local dealer information, visit the
find a showroom section of our website, subzero.com.
The Sub-Zero custom panel mounting kit eliminates the need
for the backer and spacer panels and is avail­able through an
authorized Sub-Zero dealer. For local dealer information, visit
the find a showroom section of our website, subzero.com.
The kit consists of mounting cleats, screws, and gages used
to properly position the cleats. The kit is available for all
Classic models except glass door models. Dual installations
require two mounting kits.
PARTIAL FRAMED PANEL
W
BI-42SD
15 1/16"
(383)
BI-48SD
18 3/4"
(476)
O VER LAY PA N ELS
Overlay panels are typically created by combining a 3/4" (19)
custom panel, a .10" (3) spacer panel, and a 1/4" (6) backer
panel. Refer to the illustrations below.
When installing two units side by side, refer to page 16 for
dual standard installations.
CUSTOM
PANEL
SPACER PANEL
SPACER
PANEL
CUSTOM PANEL
BACKER PANEL
BACKER
PANEL
TRIM
5/16" (8) min
1/8" (3) (OVERLAY)
Panel assembly (cross section)
20 | Sub-Zero Customer Care 800.222.7820
3/4"
(19)
typical
.10" (3) 1/4" (6)
Panel assembly (rear view)
C L AS S IC R EF R I GE RATION
Custom Panels
F LUS H INS ET PA NE L S
I C E A N D WATER D I S P EN S ER
The flush inset application is an overlay model with flush
inset panels. It is not a separate model.
For models BI-42SD and BI‑48SD, the refrigerator door
panel must include a cutout to accommodate the external
dispenser. The bezel will accommodate a 1/4" (6) thick panel
for framed applications and a 3/4" (19) thick panel for overlay
and flush inset applications. Panels thicker than 3/4" (19)
must be routed in the dispenser area to 11/8" (29) (including
backer and spacer panels).
The flush inset design allows custom panels to be installed
flush with adjacent cabinets. Similar to overlay, flush inset
panels are typically created by combining a 3/4" (19) custom
panel, a .10" (3) spacer panel, and a 1/4" (6) backer panel.
Refer to the illustrations for overlay panels.
For flush inset panels thicker than 3/4" (19), a 90° door stop
may be required to prevent interference with adjacent
cabinets. Refer to the full-scale templates at the end of this
guide.
When installing two units side by side, refer to page 17 for
dual flush inset installations.
1/4"
(6)
6 1/4" (159)
12 7/8"
(327)
Dispenser dimensions
subzero.com | 21
C L AS S IC R EF R I GE RATION
Framed Panel Dimensions
H H
H H H
H H
A A
H H
H H AH A
A A A
H H H
H H
H H H
A A A
H AH AH H
A AH A
H H
H H AH A
A A A
A A
H H
B B
W W W W W
BI-30U, BI-36U(ID)
H H H
H H
W
H
35 3/4" (908)
69 9/16" (1767)
W
H H H H H H
8 15/16" (227)
GRI L L E ( O P T I O N A L) H H H H H
35 3/4" (908)
BI-36RG
A
5 3/16A" A(132)
A
Stiles / Rails
B B
B
A A
10 5/16" (262)
W
(1268)
W
H
29 3/4" (756)
18 11/16" (475)
GRI L L E ( O P T I O N A L)
Grille Panel
H H
H H H
H H
H H H
W W W W W
BI-30UG, BI-36UG
W W W W W
BI-36UFD(ID),
BI-42UFD(ID)
REFRIGERATOR
Door Panel
FREEZER
Drawer Panel
GRIL L E (OPTION AL )
Grille Panel
W
H
35 3/4" (908)
49 15/16" (1268)
W
H
35 3/4" (908)
18 11/16" (475)
W
H
35 3/4" (908)
8 15/16" (227)
A
5 3/16" (132)
H
W W W3 W W
W W W W W
29 /4" (756)
49 15/16"
FREEZER
Drawer Panel
W W W WWWW W W W
A A A
Stiles / Rails
R E F R I G E R AT O R
W W W W W
W
H H H
BI-36U G
B B B
MODEL BI-30U, BI-30UG
W W W W
Door
Panel
H H
MODEL BI-36U(ID), BI-36UG
R E F R I G E R AT O R / F RE E Z E R
Grille Panel
A AH A
H AH AH H
H H H
MODEL BI-36R, BI-36RG, BI-36F
Door Panel
H H H
H H H
W W W W W
BI-36RG
H H
H H
A A A
B B B
W W W W W
BI-36R, BI-36F
H H H
H H
A A
W
H
29 3/4" (756)
8 15/16" (227)
BI-30UG
Stiles / Rails
A
5 3/16" (132)
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PAN EL S)
Door Panel
FREEZER
Drawer Panel
GRIL L E (OPTION AL )
Grille Panel
W
H
17 5/8" (448)
49 15/16" (1268)
W
H
35 3/4" (908)
18 11/16" (475)
W
H
35 3/4" (908)
8 15/16" (227)
MODEL BI-42UFD(ID)
REFRIGERATOR (2 PAN EL S)
Door Panel
FREEZER
Drawer Panel
GRIL L E (OPTION AL )
Grille Panel
22 | Sub-Zero Customer Care 800.222.7820
W
H
20 5/8" (524)
49 15/16" (1268)
W
H
41 3/4" (1060)
18 11/16" (475)
W
H
41 3/4" (1060)
8 15/16" (227)
C L AS S IC R EF R I GE RATION
WW
AA
HH
WW
HH
HH
BB
WW
WW
WW
WW
WW
Framed Panel Dimensions
HH
HH
HH
HH
AA
BB
WW
WW
BI-36S, BI-42S(ID),
BI-48S(ID)
WW
WW
BI-42SD, BI-48SD
MODEL BI-36S
MODEL BI-48S, BI-48SID, BI-48SD
R E F R I G E R AT O R
Door Panel
W
H
19 13/16" (503)
69 9/16" (1767)
FREEZER
Door Panel
W
H
15 7/16" (392)
69 9/16" (1767)
GRI L L E ( O P T I O N A L)
Grille Panel
W
H
35 3/4" (908)
8 15/16" (227)
REFRIGERATOR
Door Panel
FREEZER
Door Panel
GRIL L E (OP TION AL )
Grille Panel
BI-48SD
Dispenser Cutout*
MODEL BI-42S, BI-42SID, BI-42SD
R E F R I G E R AT O R
Door Panel
FREEZER
Door Panel
GRI L L E ( O P T I O N A L)
Grille Panel
BI-42SD
Dispenser Cutout*
Cutout Location
W
H
24 13/16" (630)
69 9/16" (1767)
W
H
16 7/16" (418)
69 9/16" (1767)
W
H
41 3/4" (1060)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
1 7/8" (48)
28 3/4" (730)
Cutout Location
W
H
28 1/2" (724)
69 9/16" (1767)
W
H
18 3/4" (476)
69 9/16" (1767)
W
H
47 3/4" (1213)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
1 7/8" (48)
28 3/4" (730)
*For models BI-42SD and BI-48SD, panel thickness in dispenser area can
range from 1/4" (6) to 1 1/8" (29) max. If panel is thicker, rout out 1/4" (6) min flat
landing area to accommodate dispenser.
subzero.com | 23
C L AS S IC R EF R I GE RATION
Overlay Panel Dimensions
H H
H H H
H H
H H
H H AH A
H H H
H H
H H H
A A A
A A
A A A
H AH AH H
A AH A
H H
H H AH A
A A A
A A
H H
B B
W W W W W
BI-30U, BI-36U(ID)
H H H
H H
H H H
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
69 3/4" (1772)
15/16" (1751)
68
H H H H H
69 9/16" (1767)
GRI L L E
Overlay Panel
Spacer Panel
Backer Panel
W
H
36"
(914)
A A A
35 1/8" (892)
B B
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
B
8 15/16" (227)
BI-36RG
Stiles / Rails
W W W W W
W W W W W
A A
B B
A
B
5 1/4" (133)
10 3/8" (264)
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
19" (483)
18 1/16" (459)
18 11/16" (475)
W W W W W
W W W W W
MODEL BI-30U, BI-30UG
R EF R I G E R AT O R
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRI L L E
Overlay Panel
Spacer Panel
Backer Panel
H H
H H H
W W W WWWW W W W
A A A
H H
H H H
H H
H H H
W W W W W
BI-30UG, BI-36UG
W W W W W
BI-36UFD(ID),
BI-42UFD(ID)
MODEL BI-36U(ID), BI-36UG
R E F R I G E R AT O R / F RE E Z E R
H H
A AH A
H AH AH H
H H H
MODEL BI-36R, BI-36RG, BI-36F
Overlay Panel
Spacer Panel
Backer Panel
H H H
H H H
W W W W W
BI-36RG
H H
H H
A A A
B B B
W W W W W
BI-36R, BI-36F
H H H
H H
A A
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
BI-30UG
Stiles / Rails
24 | Sub-Zero Customer Care 800.222.7820
A
5 1/4" (133)
REFRIGERATOR
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRIL L E
Overlay Panel
Spacer Panel
Backer Panel
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
BI-36U G
A
5 1/4" (133)
Stiles / Rails
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PAN EL S)
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRIL L E
Overlay Panel
Spacer Panel
Backer Panel
W
H
17 7/8" (454)
17" (432)
17 5/8" (448)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
C L AS S IC R EF R I GE RATION
WW
AA
HH
WW
HH
HH
BB
WW
WW
WW
WW
WW
Overlay Panel Dimensions
HH
MODEL BI-42S, BI-42SID, BI-42SD
HH
REFRIGERATOR
HH
Overlay Panel
Spacer Panel
Backer Panel
HH
W
H
25 1/16" (637)
24 3/16" (614)
24 13/16" (630)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
AA
BB
WW
WW
BI-36S, BI-42S(ID),
BI-48S(ID)
WW
W
H
16 11/16" (424)
15 13/16" (402)
16 7/16" (418)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
GRIL L E
Overlay Panel
Spacer Panel
Backer Panel
WW
W
H
42" (1067)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
BI-42SD
BI-42SD, BI-48SD
Dispenser Cutout
W
H
5 7/8" (149)
12 7/16" (316)
Cutout Location
MODEL BI-42UFD(ID)
R E F R I G E R AT O R ( 2 PANE LS)
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRI L L E
Overlay Panel
Spacer Panel
Backer Panel
H
20 7/8" (530)
20" (508)
20 5/8" (524)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
42" (1067)
41 1/8" (1045)
41 3/4" (1060)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
42" (1067)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
REFRIGERATOR
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRIL L E
Overlay Panel
Spacer Panel
Backer Panel
BI-48SD
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRI L L E
Overlay Panel
Spacer Panel
Backer Panel
B
28 13/16" (732)
MODEL BI-48S, BI-48SID, BI-48SD
W
Dispenser Cutout
MODEL BI-36S
R EF R I G E R AT O R
A
2" (51)
W
H
20 1/16" (510)
19 3/16" (487)
19 13/16" (503)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
15 11/16" (398)
14 13/16" (376)
15 7/16" (392)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
Cutout Location
W
H
28 3/4" (730)
27 7/8" (708)
28 1/2" (724)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
19" (483)
18 1/8" (460)
18 3/4" (476)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
48" (1219)
47 1/8" (1197)
47 3/4" (1213)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
2" (51)
28 13/16" (732)
*Panel height may be increased by 7/16" (11) to hide upper main frame. Also
refer to Classic panel configurator at subzero.com/trade/panels.
Grille panel dimensions are for standard 84" (2134) overall unit height. For
83" (2108) height, subtract 1" (25) from grille panel height dimensions and for
88" (2235) height, add 4" (102). A specific panel grille must be ordered for an
83" or 88" overall unit height.
subzero.com | 25
C L AS S IC R EF R I GE RATION
Flush Inset Panel Dimensions
H H
H H H
H H
H H
H H AH A
H H H
H H
H H H
A A A
A A
A A A
H AH AH H
A AH A
H H
H H AH A
A A A
B A
H H
B B
W W W W W
BI-30U, BI-36U(ID)
H H H
H H
H H H
H H H
W W W W W
BI-30UG, BI-36UG
W W W W W
BI-36UFD(ID),
BI-42UFD(ID)
W
H
Flush Inset Panel
Spacer Panel
Backer Panel
37" (940)
35 1/8" (892)
35 3/4" (908)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
37"
(940)
A A A
35 1/8" (892)
B B
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
B
8 15/16" (227)
A A
B B
B
R EF R I G E R AT O R
W
H
Flush Inset Panel
Spacer Panel
Backer Panel
31" (787)
29 1/8" (740)
29 3/4" (756)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
19" (483)
18 1/16" (459)
18 11/16" (475)
W W W W W
W W W W W
MODEL BI-30U, BI-30UG
FREEZER
GRI L L E
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
BI-30UG
Stiles / Rails
H H
REFRIGERATOR
10 3/8" (264)
Flush Inset Panel
Spacer Panel
Backer Panel
H H H
69 3/4" (1772)
15/16" (1751)
68
H H H H H
69 9/16" (1767)
A
Flush Inset Panel
Spacer Panel
Backer Panel
H H
37" (940)
35 1/8" (892)
35 3/4" (908)
5 3/4" (146)
W W W W W
W W W W W
W W W WWWW W W W
B B B
H
BI-36RG
Stiles / Rails
H H H
W
GRI L L E
Flush Inset Panel
Spacer Panel
Backer Panel
H H
MODEL BI-36U(ID), BI-36UG
R E F R I G E R AT O R / F RE E Z E R
H H
H AH AH H
A AH A
H H H
MODEL BI-36R, BI-36RG, BI-36F
Flush Inset Panel
Spacer Panel
Backer Panel
H H H
H H H
W W W W W
BI-36RG
H H
H H
B B B
B B B
W W W W W
BI-36R, BI-36F
H H H
H H
B A
A
B
5 3/4" (146)
5 1/4" (133)
26 | Sub-Zero Customer Care 800.222.7820
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
BI-36U G
Stiles / Rails
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
A
B
5 3/4" (146)
5 1/4" (133)
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PAN EL S)
Flush Inset Panel
Spacer Panel
Backer Panel
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
18 3/8" (467)
17" (432)
17 5/8" (448)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
C L AS S IC R EF R I GE RATION
WW
AA
HH
WW
HH
HH
BB
WW
WW
WW
WW
WW
Flush Inset Panel Dimensions
HH
MODEL BI-42S, BI-42SID, BI-42SD
HH
HH
HH
REFRIGERATOR
W
H
Flush Inset Panel
Spacer Panel
Backer Panel
25 9/16" (649)
24 3/16" (614)
24 13/16" (630)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
AA
BB
WW
WW
BI-36S, BI-42S(ID),
BI-48S(ID)
WW
W
H
17 3/16" (437)
15 13/16" (402)
16 7/16" (418)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
WW
W
H
43" (1092)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
BI-42SD
BI-42SD, BI-48SD
Dispenser Cutout
W
H
5 7/8" (149)
12 7/16" (316)
Cutout Location
MODEL BI-42UFD(ID)
R E F R I G E R AT O R ( 2 PANE LS)
Flush Inset Panel
Spacer Panel
Backer Panel
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRI L L E
Flush Inset Panel
Spacer Panel
Backer Panel
MODEL BI-48S, BI-48SID, BI-48SD
H
REFRIGERATOR
W
H
21 3/8" (543)
20" (508)
20 5/8" (524)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
Flush Inset Panel
Spacer Panel
Backer Panel
29 1/4" (743)
27 7/8" (708)
28 1/2" (724)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
43" (1092)
41 1/8" (1045)
41 3/4" (1060)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
43" (1092)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
BI-48SD
Dispenser Cutout
R E F R I G E R AT O R
W
H
Flush Inset Panel
Spacer Panel
Backer Panel
20 9/16" (522)
19 3/16" (487)
19 13/16" (503)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
FREEZER
GRI L L E
Flush Inset Panel
Spacer Panel
Backer Panel
B
28 13/16" (732)
W
MODEL BI-36S
Flush Inset Panel
Spacer Panel
Backer Panel
A
2" (51)
W
H
16 3/16" (411)
14 13/16" (376)
15 7/16" (392)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
Cutout Location
W
H
19 1/2" (495)
18 1/8" (460)
18 3/4" (476)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
49" (1245)
47 1/8" (1197)
47 3/4" (1213)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
2" (51)
28 13/16" (732)
Grille panel dimensions are for standard 84" (2134) overall unit height. For
83" (2108) height, subtract 1" (25) from grille panel height dimensions and for
88" (2235) height, add 4" (102). A specific panel grille must be ordered for an
83" or 88" overall unit height.
subzero.com | 27
C L AS S IC R EF R I GE RATION
TOP VIEW
BACKER
SPACER
PANEL O F F S ET
5/16" (8)
5/8"
(16)
The illustrations provide panel offsets and reveals for Classic
models in a flush inset application. Refer to the chart below
5/16" (8)
for reference to the illustrations.
BACKER
CABINETRY
SPACER
Door / Grille Sides
Grille Top
Grille Bottom / Door Top
Door Bottom
5/16A
" (8)
Door (hinge) / Drawer / Grille Sides
Doors (handle) Sides (French door only)
Grille Top
Grille Bottom / Door Top
Door Bottom / Drawer Top
Drawer Bottom
5/8"
(16)
GRILLE
SI D E - B Y- S I D E
IL L U S
Doors (hinge) / Grille Sides
Doors (handle) Sides
Grille Top
Grille Bottom / Door Top
Door Bottom
A
CABINETRY
B
C
D
F
GRILLE
1/2"
(13)
CABINETRY
5/8"
(16)
1/2"
(13)
1/8" (3)
DOOR
DOOR
DOOR
1/4" (6)
TOP VIEW REVEAL
5/16" (8)
5/16" (8)
DOOR
1/8" (3)
DOOR
DOOR
1/8" (3)
1/4" (6)
DOOR
1/4" (6)
REVEAL
1/2" (13)
1
SIDE 5
VIEW /8"
/16" (3)GRILLE
CABINETRY
1/2" (13)
1/8"
5/16
" (3)
GRILLE
SIDE
VIEW
(8)
SIDE VIEW
5/16"
(8) 3/32"
(2)
DOOR
1/8" (3)
5/16"
(8) 5/32"
(4)
GRILLE
Illus. B
CABINETRY
5/16" (8)
1/8" (3)
1/4" (6)
REVEAL
1/2" (13)
GRILLE
(8)
5/16" (8)
1/4" (6)
1/8"
5/16" (3)
(8)
1/2" (13)
1/2" (13)
DOOR
GRILLE
GRILLE
SIDE VIEW
1/2" (13)
DOOR
GRILLE
5/16"
DOOR
GRILLE
32
(8) 53//32
""
5/16" (4)
(2)
(8)
SIDE VIEW
1/2" (13)
Illus.DOOR
D
DOOR /
DRAWER
DOOR
3/32"
5/16" (2)
(8)
SIDE VIEW
5/16"
(8) 3/32"
(2)
5/16"
(8) 5/32"
(4)
1/2
3/532
/16
" " DOOR
5/16" (2)
(8) 5/32GRILLE
"
(4)
(8)
1/8"
5/16
" (3)
SIDE
VIEW
(8)
SIDE VIEW
REVEAL
1/2" (13)
1/8"
5SIDE
VIEW
/16" (3)
(8)
Illus. C
DOOR /
DRAWER
5/16"
35/32"
/32"
5/(8)
16" (2)
(4)
(8)
SIDE VIEW
1/2
5/16"
32""
(8) 53//32
5/16" (4)
(2)
(8)
SIDE VIEW
1/2
3/32"
5/16" (2)
(8)
SIDE VIEW
DOOR
5/8" (16)
DRAWER
DOOR
5/16"
5/32
(8)" 3/DRAWER
32"
5/16" (4)
(2)
(8)
DOOR
SIDE VIEW
DRAWER
DOOR
5/8" (16)
5/16"
DRAWER
35//32
(8)
Illus.
32"E
"
5/16" (2)
(4)
(8) DOOR
5/8" (16)
SIDE VIEW
DRAWER
5/DRAWER
32"
5/16" (4)
(8)
SIDE VIEW
28 | Sub-Zero Customer Care 800.222.7820
1/4" (6)
REVEAL
TOP VIEW
REVEAL
Illus. A
A
1/8"
B 5/16" (3)
(8)
C
CABINETRY
D
E
F
GRILLE
DOOR
CABINETRY
5/8"
(16)
5/16" (8)
1/2"
(13)
1/2" (13)
IL L U S
5/16" (8)
1/8" (3)
FLUSH INSET PANEL
IL L U S
OV E R - A N D - U N D E R
TOP VIEW
5/16" (8)
5/CABINETRY
8"
(16)
5/16" (8)
BACKER
CABINETRY
FLUSH INSET PANEL
C
CABINETRYD
F
1/2"
(13)
TOP VIEW
5/8"
SPACER
(16)
PANEL OFFSET
DOOR
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
1/2"
(13)
BACKER
SPACER
DOOR
TOP VIEW
TOP VIEW
5/16" (8)
1/2"
(13)
TOP VIEW
DOOR
CABINETRY
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
A L L R E F R I G E R AT O R / ALL FRE E Z E R
DOOR
CABINETRY
BACKER
SPACER
TOP VIEW
BACKER
SPACER
TOP VIEW
DOOR / DRAWER / GRILLE
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
Flush Inset Panels
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
5/8" (16)
DOOR /
DRAWER
5/16"
(8) 53/32"
5/16" (4)
(2)
(8)
SIDE VIEW
5
/8" (16)
5/16"
(8) 35//32
32""
5/16" (2)
(4)
(8)
5/8" (16)
SIDE VIEW
SIDE VIEW
DOOR /
DRAWER
5/16"
(8)
DOOR /
DRAWER
3/32" (4) DOOR
5/32" (2) DRAWER
5/16" SIDE VIEW
(8) DOOR /
DRAWER
5/16"
(8)
3/32"
5/32
(2"
5/"16
(8)
Illus. F
SIDE VIEW
3/32" (4) DOOR
5/32
5/16
" (2)
DRAWER
VIEW
" SIDE
(8)
3/32"
5/32
5/16
" (2
"
(8)
5/32"
5/16" (4)
(8)
SIDE VIEW
SIDE VIEW
3/32" (4) DOOR
5/32" (2)SIDE
DRAWER
VIEW
3/32" (
5/32" (2
C L AS S IC R EF R I GE RATION
Dual Installation
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom filler strip
require a dual installation kit. If a dual installation kit is not
specified, a 2" (51) filler strip is recommended between
the units. A custom filler strip is required when installing
two French door or side-by-side models. Dual installations
without a filler strip can only be accomplished using two 84"
(2134) units with opposite hinges. Refer to the illustrations
below.
For dual standard installations, panel dimensions are the
same as for single installations. Refer to the charts on pages
22–25. Panel dimensions and offsets for dual flush inset
installations are listed on the following pages.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero Customer
Care at 800-222-7820.
WITHOUT FILLER STRIP
Opposite hinges
FILLER STRIP
Same side hinges
subzero.com | 29
C L AS S IC R EF R I GE RATION
Dual Flush Inset Panel Dimensions
H H
H H
H H
H H
H H
H H A AH AH A
A A
H H
H H
A A
A A
H H
A AH H
H H
H H A AH AH A
A A
H H
H H
W W
W W
BI-36R, BI-36F
B B
W W
W W
W W
W W
BI-36RG
H H
H H
W W
W W
W W
W W
W W
BI-30UG, BI-36UG
REFRIGERATOR
W
H
Flush Inset Panel
Spacer Panel
H H
Backer Panel
36 1/2" (927)
35 1/8" (892)
35 3/4" (908)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
36 1/A2" A(927)
35 1/8" (892)
B B
35 3/4" (908)
9 1/4"A(235)
A
8 5/16" (211)
B
8 15/16" (227)
W
W
WW
A
B
5 3/4" (146)
10 3/8" (264)
W W
W W
H
Flush Inset Panel
Spacer Panel
Backer Panel
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
FREEZER
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
19" (483)
18 1/16" (459)
18 11/16" (475)
GRI L L E
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
BI-30UG
A
B
5 3/4" (146)
5 1/4" (133)
30 | Sub-Zero Customer Care 800.222.7820
FREEZER
B
W W
W
Stiles / Rails
H H
H H
69 3/4" (1772)
15/16" (1751)
68
H H
69 9/16" (1767)
R EF R I G E R AT O R
Flush Inset Panel
Spacer Panel
Backer Panel
W W
36 1/2" (927)
35 1/H8" H(892)
35 3/4" (908)
MODEL BI-30U, BI-30UG
Flush Inset Panel
Spacer Panel
Backer Panel
W W
W W
W W
H
BI-36RG
Stiles / Rails
H H
W
GRI L L E
Flush Inset Panel
Spacer Panel
Backer Panel
H H
MODEL BI-36U(ID), BI-36UG
R E F R I G E R AT O R / F RE E Z E R
H H
A AH H
H H
H H
MODEL BI-36R, BI-36RG, BI-36F
Flush Inset Panel
Spacer Panel
Backer Panel
H H
H H
H H
W W
BI-30U, BI-36U(ID)
H H
W W
B B
B A
B B
H H
B B
B A
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
BI-36U G
Stiles / Rails
W
H
36 1/2" (927)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
36 1/2" (927)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
A
B
5 3/4" (146)
5 1/4" (133)
Grille panel dimensions are for standard 84" (2134) overall unit height.
C L AS S IC R EF R I GE RATION
TOP VIEW
BACKER
SPACER
D U AL F LUS H IN SE T PANE L OFFSE T
5/16" (8)
5/8"
(16)
A L L R E F R I G E R AT O R / ALL FRE E Z E R
OV E R - A N D - U N D E R
Door (hinge) / Drawer / Grille Sides
Door (handle) Sides
Grille Top
Grille Bottom / Door Top
Door Bottom / Drawer Top
Drawer Bottom
5/16" (8)
1/2"
(13)
BACKER
CABINETRY
SPACER
IL L U S
GRILLE
TOP VIEW
DOOR
TOP VIEW
5/16" (8)
5/16" (8)
1/8" (3)
DOOR
5/CABINETRY
8"
(16)
BACKER
1/4" (6)
1/8" (3)
DOOR
DOOR
DOOR
1/4" (6)
REVEAL
TOP VIEW
TOP VIEW REVEAL
DUAL
TRIM
5/16" (8)
1/2"
(13)
1/2"
(13)
CABINETRY
5/8"
(16)
5/16" (8)
5/16" (8)
DOOR
1/8" (3)
DOOR
DOOR
1
/8" (3)
1/4" (6)
DOOR
1/4" (6)
REVEAL
REVEAL
FLUSH INSET PANEL
5/16" (8)
CABINETRY
1/2" (13)
5/8"
(16)
1/2"
(13)
CABINETRY
1/8"
5/16" (3)
(8)
1/2" (13)
GRILLE
SIDE VIEW
DOOR
GRILLE
1/2" (13)
DOOR
DOOR
3/32
GRILLE
"
5/16" (2)
(8)
SIDE VIEW
DOOR /
DRAWER
5/16"
35/32"
/32"
5/(8)
16" (2)
(4)
(8)
SIDE VIEW
1/2
5/16"
32""
(8) 53//32
5/16" (4)
(2)
(8)
SIDE VIEW
1/2
DOOR
DOOR /
DRAWER
5/16"
(8) 3/32"
(2)
5/16"
(8) 5/32"
(4)
1/2
SIDE VIEW
Illus. D
SIDE VIEW
GRILLE
3/532
/16" " DOOR
5/16" (2)
(8) 5/32GRILLE
"
(4)
(8)
1/8"
5/16
" (3)
SIDE
VIEW
(8)
Illus. C
5/16"
(8) 3/32"
(2)
1/4" (6)
REVEAL
1/2" (13)
1/8"
5SIDE
VIEW
/16" (3)
(8)
1/2" (13)
DOOR
5/16"
(8) 5/32"
(4)
GRILLE
Illus. B
5/16" (3)GRILLE
(8)
1/8" (3)
1/8" (3)
REVEAL
1/2" (13)
1/8"
5/16" (8)
5/16" (8)
1/4" (6)
Illus. A
A 5/16" (3)
GRILLE
(8)
B
CABINETRY
CABINETRY
C
1/2" (13)
D
E
1
F
SIDE VIEW /8"
GRILLE
1/2"
(13)
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
IL L U S
A
B
CABINETRYC
D
F
DOOR
TOP VIEW
TOP VIEW
5/8"
SPACER
(16)
PANEL OFFSET
DOOR
CABINETRY
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
The illustrations provide panel offsets and reveals for
Classic
FLUSH
INSET PANEL
models in a dual flush inset application. Refer to the chart
5/16" (8)
below for reference to the illustrations.
Door (hinge) / Grille Sides
Door (handle) Sides
Grille Top
Grille Bottom / Door Top
Door Bottom
DOOR
CABINETRY
BACKER
SPACER
TOP VIEW
BACKER
SPACER
TOP VIEW
DOOR / DRAWER / GRILLE
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
Dual Installation
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
3/32"
5/16" (2)
(8)
SIDE VIEW
DOOR
5/8" (16)
DRAWER
DOOR
5/16"
5/32
(8)" 3/DRAWER
32"
5/16" (4)
(2)
(8)
DOOR
SIDE VIEW
DRAWER
5/8" (16)
5/DRAWER
Illus.
32E
"
5/16" (4)
(8) DOOR
SIDE VIEW
DRAWER
5/8" (16)
DOOR /
DRAWER
5/16"
(8) 53/32"
5/16" (4)
(2)
(8)
SIDE VIEW
5
/8" (16)
5/16"
(8) 35//32
32""
5/16" (2)
(4)
(8)
5/8" (16)
SIDE VIEW
5/16"
(8)
DOOR /
DRAWER
3/32" (4) DOOR
5/32" (2) DRAWER
5/16" SIDE VIEW
(8) DOOR /
SIDE VIEW
DRAWER
5/16"
(8)
3/32"
5/32
(2"
5/"16
(8)
Illus. F
SIDE VIEW
3/32" (4) DOOR
5/32" (2)SIDE
DRAWER
VIEW
3/32"
5/32
5/16
" (2
"
(8)
5/32"
5/16" (4)
(8)
SIDE VIEW
SIDE VIEW
subzero.com | 31
3/32" (
5/32" (2
C L AS S IC R EF R I GE RATION
Dual Installation
D U AL WIDE G R IL L E
DUAL WIDE GRILLE—FLUSH INSET
A dual wide grille spans the entire width of both units in a
dual installation and is a part of a dual installation kit.
TWO 30" MOD EL S
For overlay and flush inset panel dimensions for the dual
wide grille, refer to the charts below. Dimensions listed are
for a standard 84" (2134) finished height.
DUAL WIDE GRILLE—OVERLAY
T WO 3 0 " M O D E L S
Overlay Panel
Spacer Panel
Backer Panel
W
H
60 1/4" (1530)
59 3/8" (1508)
60" (1524)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
30" A N D 3 6 " M O D E L
Overlay Panel
Spacer Panel
Backer Panel
W
H
66 1/4" (1683)
65 3/8" (1661)
66" (1676)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
T WO 3 6 " M O D E L S
Overlay Panel
Spacer Panel
Backer Panel
W
H
72 1/4" (1835)
71 3/8" (1813)
72" (1829)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
32 | Sub-Zero Customer Care 800.222.7820
Flush Inset Panel
Spacer Panel
Backer Panel
30" AN D 36" MOD EL
Flush Inset Panel
Spacer Panel
Backer Panel
TWO 36" MOD EL S
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
61 1/4" (1556)
59 3/8" (1508)
60" (1524)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
67 1/4" (1708)
65 3/8" (1661)
66" (1676)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
73 1/4" (1861)
71 3/8" (1813)
72" (1829)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
C L AS S IC R EF R I GE RATION
Side Panel
Standard Handles
The custom side panels must be a minimum of 24" (610)
deep and 1/2" (13) thick. Routing will be necessary for the
side panel to fit flush against the side of the unit. Refer to
the illustrations below.
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
When installing a Classic unit with a custom side panel, an
accessory kit is required. Stainless steel and white enamel
side panels are available for an 84" (2134) finished height
through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
Refer to the chart below for standard handle lengths for
Classic models.
24" (610)
FRONT
OF SIDE
PANEL
HANDLE LENGTH
TU BU L A R
PRO
Full Door
63 7/8"
Over-and-Under Door
44 1/4"
30" Drawer
24 5/16" (633)
17 9/16" (447)
36" Drawer
30 5/16" (770)
23 5/8" (600)
42" Drawer
36 5/16" (922)
29 5/8" (753)
(1622)
(1124)
45 3/16"
(1147)
37 1/2"
(952)
1" (25)
1 7/8" (48)
1/8" (3)
1/2" (13)
ROUT TO 1/8" (3)
1 7/8"(48)
84"
1" (25)
MAIN
FRAME
SIDE PANEL
ROUTING
(2134)
Routing detail
4 1/4" (108)
ROUT TO
3/16" (5)
(OVER-AND-UNDER
MODELS)
5 3/4"
(146)
20 1/2"
(521)
4" (102)
OPTIONAL
TOE KICK
CUT-OUT
2 5/8"
(67)
Side panel dimensions
subzero.com | 33
C L AS S IC R EF R I GE RATION
Framed Panels
F ULL-S CALE T E MPL ATE
OPTIONAL EXTENDED
FULL-LENGTH HANDLE
STANDARD
FULL-LENGTH HANDLE
2"
1"
(51)
(25)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
1/2" (13) PANEL
1/4" (6) FRAMED PANEL
DOOR
Framed panel thickness
34 | Sub-Zero Customer Care 800.222.7820
C L AS S IC R EF R I GE RATION
Overlay | Flush Inset Panels
F ULL-S CALE T E MPL ATE
Overlay and flush inset panels must be a minimum of 5/8"
(16) thick to support mounting the handle. Panel thickness
does not include the backer and spacer panels. Mount the
handle close to the opening edge of the door.
DEPTH OF TUBULAR
AND PRO HANDLES
1"
2"
(25)
(51)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
.10" (3) SPACER PANEL
1/4" (6) BACKER PANEL
DOOR
Overlay and flush inset panel thickness
subzero.com | 35
C L AS S IC R EF R I GE RATION
Overlay Application
F ULL-S CALE T E MPL ATE
237/8" (606)
TO REAR OF UNIT
OVERALL WIDTH OF UNIT
0" (0)
1/4" (6)
1/2" (13)
3/4" (19)
1" (25)
11/4" (32)
11/2" (38)
13/4" (44)
2" (51)
21/4" (57)
21/2" (63)
23/4" (70)
3" (76)
31/4" (83)
31/2" (89)
1" (25) THICK
PANEL
3/4" (19) THICK
OVERLAY PANEL
(TYPICAL)
1/4" (6) BACKER
PANEL
0"
1" (25)
SCALE
90° door opening (top view)
36 | Sub-Zero Customer Care 800.222.7820
C L AS S IC R EF R I GE RATION
Flush Inset Application
F ULL-S CALE T E MPL ATE
24" (610)
TO BACK WALL
For panels thicker than 3/4" (19), a 90° door stop may be
required to prevent interference with adjacent cabinets.
1 1/4" (32)
2 3/16" (56)
ASSUMES
3/4" (19)
FLUSH INSET
PANEL
THICKNESS
1" (25) THICK
PANEL
3/4" (19) THICK
FLUSH INSET PANEL
(TYPICAL)
1/4" (6) BACKER
PANEL
0"
1" (25)
SCALE
110° door opening (top view)
subzero.com | 37
C L AS S IC R EF R I GE RATION
FILLER STRIP
11/4" (32)
APPROX PROFILE OF
STAINLESS STEEL WRAPPED
DOOR AND HANDLE
Dual Standard Installation
F ULL-S CALE T E MPL ATE
Typical framed, overlay, or stainless steel dual installation
with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.
0"
1" (25)
SCALE
Dual standard installation (top view)
38 | Sub-Zero Customer Care 800.222.7820
DOOR
CLOSED
DOOR
OPEN 110°
C L AS S IC R EF R I GE RATION
FILLER STRIP
1 1/2" (38)
1/2" (13)
PROFILE OF 3/4" (19) FLUSH INSET PANEL
AND TUBULAR HANDLE
Dual Flush Inset Installation
DOOR
CLOSED
DOOR
OPEN 110°
F ULL-S CALE T E MPL ATE
Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90°
door stop.
0"
1" (25)
SCALE
Dual flush inset installation (top view)
subzero.com | 39
P R O R E F R I G E R AT I O N
40 | Sub-Zero Customer Care 800.222.7820
P RO R EF R IG ER ATION
PRO Refrigeration
Freshness finds unmistakable expression with Sub-Zero
PRO Refrigeration. A monument to food preservation—
equal parts sculpted metal design statement and culinary
secret weapon. Its vast interior, like its bold exterior, is
crafted of stainless steel. Available in 36" and 48" widths,
with a glass or solid door, and may be either built in or
freestanding.
P R O M O D ELS
PRO3650
PRO3650G
PRO4850
PRO4850G
subzero.com | 41
P RO R EF R IG ER ATION
Overall Dimensions
3 6" MO DEL
25 7/8" (657)
36" (914)
84"
(2134)
42 1/8"
(1070)
30 1/2"
(775)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
30 3/16" (767)
23 7/8"
(606)
26"
(660)
26"
37 3/8"
(660)
(949)
2 3/8" (60)
Model PRO3650 / PRO3650G
SPECIFICATIONS
IN TERIOR C APAC ITY
PRO3650
PRO3650G
SH IPP IN G WEIGH T
PRO3650
PRO3650G
42 | Sub-Zero Customer Care 800.222.7820
R C U FT (L)
F CU FT (L)
18.4 (521)
18.4 (521)
4.3 (122)
4.3 (122)
LB ( K G )
630 (286)
650 (295)
P RO R EF R IG ER ATION
Overall Dimensions
4 8" MO DEL
25 7/8" (657)
48" (1219)
84"
(2134)
42 1/8"
(1070)
30 1/2"
(775)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
30 3/16" (767)
23 7/8"
23 7/8"
(606)
(606)
21"
(533)
26"
(660)
30 3/4"
(781)
14 1/2"
(368)
2 3/8" (60)
Model PRO4850 / PRO4850G
SPECIFICATIONS
IN TERIOR C APAC ITY
PRO4850
PRO4850G
SH IPP IN G WEIGH T
PRO4850
PRO4850G
R C U FT (L)
F CU FT (L)
18.7 (530)
18.7 (530)
11.7 (331)
11.7 (331)
LB ( K G )
860 (390)
880 (399)
subzero.com | 43
P RO R EF R IG ER ATION
Opening Dimensions
S TANDAR D | F LU SH INSTAL L ATION
D
3/4" (19)
OPENING
DEPTH
TYPICAL
3 1/2" (89)
FINISHED
RETURN
TOP VIEW
W
FRAMELESS
CABINETRY
3/4" (19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
H
W
OPENING
HEIGHT
OPENING WIDTH
FILLER
W
FRAMED
CABINETRY
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
STANDARD OPENING
36" Model
48" Model
H
W
35 1/2"
(902)
47 1/2" (1206)
83 3/4"
D
FLUSH OPENING
W
(2127)
24" (610)
36" Model
36" (914)
83 3/4" (2127)
24" (610)
48" Model
48" (1219)
For standard installations, the face frame will extend 2" (51)
beyond cabinetry.
44 | Sub-Zero Customer Care 800.222.7820
H
D
(2137)
26" (660)
84 1/8" (2137)
26" (660)
84 1/8"
For flush installations, the face frame will be flush with surrounding cabinetry.
P RO R EF R IG ER ATION
Opening Dimensions
D U AL S TANDARD | FL USH INSTAL L ATION
D
3/4" (19)
OPENING
DEPTH
TYPICAL
3 1/2" (89)
FINISHED
RETURN
TOP VIEW
W
FRAMELESS
CABINETRY
3/4" (19)
TYPICAL
3 1/2" (89)
FILLER
FINISHED
RETURN
H
W
OPENING
HEIGHT
OPENING WIDTH
W
FRAMED
CABINETRY
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
DUAL STANDARD OPENING
Two 36" Models
71 1/2"
H
W
(1816)
83 3/4"
(2127)
D
24" (610)
For standard installations, the face frame will extend 2" (51)
beyond cabinetry. A dual installation kit is required for this
installation.
DUAL FLUSH OPENING
Two 36" Models
W
72" (1829)
84 1/8"
H
D
(2137)
26" (660)
For flush installations, the face frame will be flush with surrounding cabinetry. A dual installation kit is required for this
installation.
subzero.com | 45
P RO R EF R IG ER ATION
Dual Installation
Electrical Requirements
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom filler strip
require a dual installation kit. If a dual installation kit is not
specified, a 2" (51) filler strip is recommended between the
units. Dual installations without a filler strip can only be
accomplished using two units with opposite hinges. Refer to
the illustrations below.
Installation must comply with all applicable electrical codes.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero Customer
Care at 800-222-7820.
ELECTRICAL REQUIREMENTS
Locate the electrical supply within the shaded area shown
in the illustration below. A separate circuit servicing only
this appliance is required. A ground fault circuit interrupter
(GFCI) is not recommended and may cause interruption of
operation.
Electrical Supply
115 VAC, 60 Hz
Service
15 amp dedicated circuit
Receptacle
3-prong grounding-type
7"
E
(178)
6"
(152)
75 1/2" (1918)
FROM FLOOR
WITHOUT FILLER STRIP
Opposite hinges
FILLER STRIP
Same side hinges
46 | Sub-Zero Customer Care 800.222.7820
RIGHT SIDE
OF OPENING
Electrical supply location
P RO R EF R IG ER ATION
Plumbing Requirements
Standard Handles
Installation must comply with all applicable plumbing codes.
Optional stainless steel pro handles are avail­able through
an authorized Sub-Zero dealer. For local dealer information,
visit the find a showroom section of our website,
subzero.com.
Locate the water supply line within the shaded area shown
in the illustration below. Connect the water supply line to the
house supply with an easily accessible shut-off valve. Do
not use self‑piercing valves. The water supply line must not
interfere with the installation of the anti-tip bracket.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. In this application, the water filtration
system must be bypassed by removing the filter. A copper
line is not recommended for this application.
Refer to the chart below for standard handle lengths for
PRO models.
HANDLE LENGTH
36" MOD EL
48" M OD E L
Door
27 11/16"
(703)
27 11/16" (703)
Refrigerator Drawer
26 3/16" (665)
19 15/16" (506)
Freezer Drawer
26 3/16" (665)
11 9/16" (294)
PLUMBING REQUIREMENTS
1/4"
Water Supply
OD copper, braided
stainless steel, or PEX tubing
Pressure
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
36" (914)
RIGHT SIDE
OF OPENING
6"
(152)
5 3/16"
(132)
3" (76)
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
Water supply location
subzero.com | 47
D E S I G N E R R E F R I G E R AT I O N
48 | Sub-Zero Customer Care 800.222.7820
D E S IG NER R EF RIGE RATION
Designer Refrigeration
With custom front panels and hardware, Sub-Zero Designer
columns, tall, and drawer models disappear into the decor.
Designer units fit flush with cabinetry, making Designer refrigeration as practical and beautiful in the master suite, bar, or
theatre room as in the kitchen. Model ID-24RO, approved for
outdoor installations, is ideal for any outdoor kitchen.
C OLUMN MO DEL S
IC-18FI
IC-24R
IC-24FI
IC-24C(I)
IC-30R(ID)
IC-30FI
IC-36R(ID)
IC-36FI
TALL MO DELS
IT-30R(ID)
IT-30FI
IT-30CI(ID)
IT-36R(ID)
IT-36CI(ID)
D RAWER MO DEL S
ID-24R
ID-24F(I)
ID-24RO
ID-27R
ID-30R(P)
ID-30F(I)
ID-30C(I)
ID-36R(P)
ID-36C(I)
subzero.com | 49
D E S IG NER R EF RIGE RATION
Specifications
INTERIOR CAPACITY— CU FT
CO L U M N
IC-18FI
IC-24R
IC-24FI
IC-24C(I)
IC-30R(ID)
IC-30FI
IC-36R(ID)
IC-36FI
TA L L
IT-30R(ID)
IT-30FI
IT-30CI(ID)
IT-36R(ID)
IT-36CI(ID)
Overall Dimensions
C O LU MN
(L )
RE FR
FRZR
8.4 (238)
W
12.9 (365)
8.0 (227)
17.3 (490)
24" (610)
4 1/2" (114)
12.3 (348)
3.1 (88)
15.3 (433)
21.4 (606)
20.0 (566)
RE FR
69 1/2"
84"*
(2134)
(1765)
FRZR
16.5 (467)
10.6 (300)
20.5 (580)
13.3 (377)
DRAWE R
RE FR
ID-24R
ID-24F(I)
ID-24RO
ID-27R
ID-30R(P)
ID-30F(I)
ID-30C(I)
ID-36R(P)
ID-36C(I)
4.0 (113)
15.1 (428)
5.0 (142)
6.4 (181)
FRZR
3.8 (108)
4.0 (113)
4.6 (130)
5.2 (147)
3.0 (85)
6.6 (187)
3.4 (96)
4.9 (139)
2.0 (57)
2.5 (71)
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
SHIPPING WEIGHT
CO L U M N
18" Column
24" Column
30" Column
36" Column
TA L L
30" Tall
36" Tall
DRAWE R
24" Drawer
27" Drawer
30" Drawer
36" Drawer
L B (KG )
260 (118)
340 (154)
400 (181)
440 (200)
A
13/4" (45)
L B (KG )
400 (181)
460 (209)
B
L B (KG )
170 (77)
190 (86)
210 (95)
250 (113)
COLUMN
IMPORTANT NOTE: Overall dimensions do not include panels
or handles. Dimensions will vary with panel thickness.
W
A
B
18" Column
18" (457)
2 1/2" (64)
16 1/2" (419)
24" Column
24" (610)
4" (102)
22 1/2" (572)
30" Column
30" (762)
5 5/8" (143)
28 1/2" (724)
36" (914)
7 1/4"
34 1/2" (876)
36" Column
50 | Sub-Zero Customer Care 800.222.7820
(184)
D E S IG NER R EF RIGE RATION
Overall Dimensions
TALL
D R AW ER
W
W
24" (610)
24" (610)
1/4" (6)
4 1/2" (114)
13 5/16"
(338)
34 1/2"*
(876)
3/8" (10)
10 9/16"
(268)
44 7/8"
84"*
(2134)
(1140)
3 5/8" (92)
*34" (864) MIN TO 35" (889) MAX
3/8" (10)
13 5/16"
(338)
3/8" (10)
10 9/16"
(268)
17 3/4"
(451)
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
DRAWER
A
13/4" (45)
17 3/4"
(451)
TA LL
W
24" Drawer
24" (610)
27" Drawer
27" (686)
30" Drawer
30" (762)
36" Drawer
36" (914)
B
W
A
B
30" Tall
30" (762)
5 5/8" (143)
28 1/2" (724)
36" Tall
36" (914)
7 1/4" (184)
34 1/2" (876)
subzero.com | 51
D E S IG NER R EF RIGE RATION
Opening Dimensions
D E S IG NER
OPENING DIMENSIONS
25" (635)
OPENING
DEPTH
25 3/4" (654)
FOR OUTDOOR
MODEL
C OL U MN / TAL L
W*
H
18" Column
24" Column
30" Column / Tall
36" Column / Tall
18" (457)
24" (610)
30" (762)
36" (914)
84" (2134)
84" (2134)
84" (2134)
84" (2134)
D RAWER
TOP VIEW
24" Drawer
27" Drawer
30" Drawer
36" Drawer
W*
H
24" (610)
27" (686)
30" (762)
36" (914)
34 1/2" (876)
34 1/2" (876)
34 1/2" (876)
34 1/2" (876)
*For stainless steel side panel accessory, add 1" (25) per panel to opening width.
H
W
OPENING
HEIGHT
OPENING WIDTH
The depth of each Designer model is 24" (610). Allow for
panel thickness when planning the finished opening depth.
A minimum 3 1/2" (89) finished return is required on all sides
of the opening—41/2" (114) for the outdoor model. Framed
cabinets require additional finished filler material behind the
face frame for a proper installation. Refer to the illustration.
D U A L I N S TA LLATI O N
When installing two units side by side in a dual installation, the opening width is the width of the two units added
together. A dual installation kit is required for this installation. If a dual installation kit is not specified, a minimum
2" (51) filler strip is required between the units.
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry—
4 1/2" (114) for outdoor model.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero Customer
Care at 800-222-7820.
P R ES S -TO -O P EN I N S TALLATI O N
3/4" (19)
3/4" (19)
TYPICAL
TYPICAL
3 1/2" (89)
3 1/2" (89)
FINISHED
RETURN
FINISHED
RETURN
W
IMPORTANT NOTE: A press-to-open installation is not Star-K
W
FRAMELESS
CABINETRY
FILLER
Column Models Only: For information regarding a press-toopen (handleless) design, refer to the guides section of any
Designer column or Designer wine column product page of
our website, subzero.com.
FRAMED
CABINETRY
52 | Sub-Zero Customer Care 800.222.7820
certified.
D E S IG NER R EF RIGE RATION
Electrical Requirements
Plumbing Requirements
Locate the electrical supply within the shaded area shown in
the illustration and chart below. A separate circuit servicing
only this appliance is required.
Locate the water supply line within the shaded area shown
in the illustration below. Connect the water supply line to the
house supply with an easily accessible shut-off valve. Do
not use self‑piercing valves. The water supply line must not
interfere with installation of the anti-tip bracket.
IMPORTANT NOTE: For outdoor model ID-24RO, a ground
fault circuit interrupter (GFCI) is required to reduce the risk
of electrical shock. A GFCI is not recommended for use with
indoor models and may cause interruption of operation.
The electrical outlet must be positioned with the grounding
prong to the right of the thinner blades.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
Installation must comply with all applicable electrical codes.
Installation must comply with all applicable plumbing codes.
ELECTRICAL REQUIREMENTS
PLUMBING REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
Service
1/4"
Water Supply
15 amp dedicated circuit
Receptacle
3-prong grounding-type
Pressure
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
ELECTRICAL SUPPLY LOCATION
18" Model
OD copper, braided stainless
steel, or PEX tubing
36" (914)
A
6" (152)
WATER SUPPLY LOCATION
A
24" Model
9 1/2" (241)
18" Model
27" Model
11" (279)
24" Model
5 1/2" (140)
30" Model
12 1/2" (318)
30" Model
6" (152)
36" Model
15 1/2"
36" Model
9" (229)
(394)
LEFT SIDE
OF OPENING
41/2"
(114)
RIGHT SIDE
OF OPENING
A
A
4 1/4"
(108)
1/4" (6)
3" (76)
FLOOR
Electrical supply location
6" (152)
3" (76)
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
Water supply location
subzero.com | 53
D E S IG NER R EF RIGE RATION
Stainless Steel Panels
Custom Panels
The outdoor model requires the use of Sub-Zero stainless
steel outdoor accessory panels. Stainless steel panels are
available through an authorized Sub‑Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com.
For Designer models, custom door panels and handle hardware must be provided. Refer to the Panel Requirements
chart and Typical Panel Dimensions.
The thickness of indoor stainless steel panels is 3/4" (19) and
outdoor stainless steel panels are 11/2" (38). The depth of
each Designer model is 24" (610). Allow for panel thickness
when planning the finished opening depth.
Reveals of 1/8" (3) are typical, however, the reveal between
the upper and lower outdoor stainless steel panel is 1/4" (6)
to accommodate the lock.
The thickness of the custom panel can vary. A minimum
5/8" (16) thick panel is required, but the thickness can be
increased provided it does not exceed the weight limit. The
depth of each Designer model is 24" (610). Allow for panel
thickness when planning the finished opening depth. Refer
to the full-scale template on page 57.
CAUTION
As reveals between cabinetry and the unit decrease,
severe finger pinching can occur while the door is
closing.
Finish all sides of the custom panels. They will be visible
when the door/drawer is open.
D-style handles are recommended. Locate the door handle
near the edge of the panel opposite the hinge and centered
top to bottom. Locate drawer handles near the top edge
of each panel. Stainless steel tubular and pro handles are
avail­able through an authorized Sub-Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com.
PANEL REQUIREMENTS
WEIGH T PER PAN EL
18" Column
24" Column
30" Column
36" Column
WEIGH T PER PA N EL
30" Tall (door)
36" Tall (door)
Drawer
PAN EL TH IC KN ESS
All Panels
54 | Sub-Zero Customer Care 800.222.7820
MAX
45 lb (20 kg)
60 lb (27 kg)
75 lb (34 kg)
75 lb (34 kg)
MAX
50 lb (22 kg)
60 lb (27 kg)
15 lb (7 kg)
M IN
5/8"
(16)
D E S IG NER R EF RIGE RATION
Custom Panels
D O O R PA N EL H EI GH T
T Y PICAL PANEL DIME NSIONS
The height of the custom door panel can extend beyond the
typical panel height, provided it does not exceed the weight
limit. Refer to the illustration below.
79 7/8"
49 3/8"
(2029)
(1254)
1 3/4"
(45)
13 9/16"
(345)
A DECORATIVE VALANCE
CANNOT EXTEND
BEYOND THIS PLANE
1/8" (3)
16 11/16"
(424)
W
Column
W
Tall
DOOR
PANEL
W
Drawer
84"
24" (610)
TO BACK OF UNIT
(2134)
Typical panel dimensions are based on an 84" (2134) finished
height for column and tall models and 34 1/2" (876) for drawer
models, with a 4" (102) toe kick and 1/8" (3) reveals. Panel
dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel height and the chart
below for panel width.
PANEL WIDTH
HINGE
W
18" Model
17 3/4"
24" Model
23 3/4" (603)
27" Model
26 3/4" (679)
30" Model
29 3/4" (756)
36" Model
35 3/4" (908)
(451)
Upper valance—column and tall (side view)
D UAL INS TALLATION
For dual installations, refer to the illustration for panel height
and the chart below for panel width.
PANEL WIDTH
W
18" Model
17 13/16"
24" Model
23 13/16" (605)
27" Model
26 13/16" (681)
30" Model
29 13/16" (757)
36" Model
35 13/16" (910)
(452)
subzero.com | 55
D E S IG NER R EF RIGE RATION
Custom Panels
Standard Handles
TOE KICK CLEARANCE
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
Indoor Models Only: The height of the toe kick area can
extend beyond the typical toe kick height, provided it does
not exceed the dimensions in the illustration below. Toe
kick heights from 2" (51) to 3 7/8" (98) require a reduced toe
kick accessory available through an authorized Sub-Zero
dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions
regarding the installation, call Sub‑Zero Customer Care at
800-222-7820.
HINGE**
VENTED
LOUVERS
24" (610)
TO BACK OF UNIT
DOOR
PANEL
1 1/8" (29)
MAX
TOE KICK
ADJUSTMENT
2" (51)*
TO
6" (152)
FROM
FLOOR
A DECORATIVE TOE KICK
CANNOT EXTEND
BEYOND THIS PLANE
*2" (51) to 3 7/8" (98) requires sales accessory.
**Column models only.
Toe kick (side view)
56 | Sub-Zero Customer Care 800.222.7820
Refer to the chart below for standard handle lengths for
Designer models.
HANDLE LENGTH
Column Door
TU BU L A R
50 1/8"
(1273)
PRO
48 3/8"
(1229)
Tall Door
33 1/4"
24" Drawer
21 1/4" (540)
19 1/2" (495)
27" Drawer
24 1/4" (616)
22 1/2" (572)
30" Drawer
27 1/4" (692)
25 1/2" (648)
36" Drawer
33 1/4"
31 1/2" (800)
(845)
(845)
31 1/2"
(800)
D E S IG NER R EF RIGE RATION
Maximum Door Opening
F ULL-S CALE T E MPL ATE
As the panel width and/or depth increases, so does the
potential for panel interference. Interference may be
minimized by using the 90° door stop.
3/4" (19) PANEL
DOOR OPEN
MAXIMUM 105°
1/8" (3) REVEAL
POTENTIAL
INTERFERENCE
DOOR CLOSED
3/4" (19) PANEL
ADJACENT
CABINETRY
POTENTIAL INTERFERENCE
0"
1" (25)
SCALE
Maximum door opening (top view)
subzero.com | 57
WINE STORAGE
58 | Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
Wine Storage
Wine finds a well-deserved place of honor in a Sub-Zero
wine storage unit. Every detail is designed to ensure better
wine preservation. Cherrywood-faced racks, soft lighting,
custom cabinetry if desired—Sub-Zero helps make a wine
collection an element of beauty in the home.
W INE S T O R AG E MODE L S
UW-24
IW-18
UW-24FS
IW-24
IW-30
IW-30R
IW-30CI
BW-30
subzero.com | 59
W INE S T O R AG E
Overall Dimensions
M ODEL UW-24
MO D EL U W-2 4 FS
23 7/8" (606)
24 1/4" (616)
24" (610)
34 3/16"
34"
(864)
(868)
4" (102)
4" (102)
25 3/8"
25 3/8"
(645)
(645)
1 3/4" (44)
1 3/4" (44)
SPECIFICATIONS
ST O R A G E C A PA C I TY
UW-24
UW-24FS
SH I P P I N G W E I G H T
UW-24
UW-24FS
*750 ml bottles.
60 | Sub-Zero Customer Care 800.222.7820
24 5/8" (625)
BOTTL ES*
46
46
L B (KG )
195 (88)
220 (100)
Overall dimensions are based on the stainless steel
models. Refer to page 83 for door clearance information.
Freestanding model UW-24FS has a finished stainless
steel exterior and handle.
W INE S T O R AG E
Opening Dimensions
M ODEL UW-24
24" (610)
OPENING
DEPTH
TOP VIEW
34 1/2"
W
(876)
OPENING
HEIGHT
OPENING WIDTH
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
3/4" (19)
3/4" (19)
TYPICAL
TYPICAL
3 1/2" (89)
3 1/2" (89)
FINISHED
RETURN
FINISHED
RETURN
W
FILLER
W
FRAMELESS
CABINETRY
OPENING WIDTH
UW-24
DUAL OPENING WIDTH
Two 24" Models*
FRAMED
CABINETRY
W
24" (610)
W
48 1/8" (1222)
*Dual installation kit required.
subzero.com | 61
W INE S T O R AG E
Overall Dimensions
C OLUMN
TALL
W
W
24" (610)
4 1/2" (114)
4 1/2" (114)
69 1/2"
84"*
(2134)
24" (610)
44 7/8"
84"*
(1765)
(2134)
(1140)
3/8" (10)
13 5/16"
(338)
3/8" (10)
10 9/16"
(268)
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
A
A
13/4" (45)
13/4" (45)
17 3/4"
B
COLUMN
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
(451)
W
A
B
IW-18
18" (457)
2 1/2" (64)
16 1/2" (419)
IW-24
24" (610)
4" (102)
22 1/2" (572)
IW-30
30" (762)
5 5/8" (143)
28 1/2" (724)
TALL
IW-30R, IW-30CI
B
W
A
B
30" (762)
5 5/8" (143)
28 1/2" (724)
IMPORTANT NOTE: Overall dimensions do not include panels
or handles. Dimensions will vary with panel thickness.
62 | Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
Specifications
STORAGE CAPACITY
CO L U M N
BOTTL ES*
IW-18
IW-24
IW-30
59
102
146
TA L L
IW-30R
IW-30CI
RE FR
FRZ R
BOTTL ES*
4.0 cu ft (113 L)
3.0 cu ft (85 L)
2.0 cu ft (57 L)
86
86
*750 ml bottles.
SHIPPING WEIGHT
CO L U M N
IW-18
IW-24
IW-30
TA L L
IW-30R, IW-30CI
L B (KG )
350 (159)
410 (186)
460 (209)
L B (KG )
490 (222)
subzero.com | 63
W INE S T O R AG E
Opening Dimensions
D E S IG NER WINE STORAGE
OPENING DIMENSIONS
25" (635)
OPENING
DEPTH
W*
18" Column
18" (457)
24" Column
24" (610)
30" Column / Tall
30" (762)
*For stainless steel side panel accessory, add 1" (25) per panel to opening width.
TOP VIEW
The depth of each Designer (IW) model is 24" (610). Allow
for panel thickness when planning the finished opening
depth. A minimum 3 1/2" (89) finished return is required on all
sides of the opening. Framed cabinets will require additional
finished filler material behind the face frame for a proper
installation. Refer to the illustration.
D U AL I N S TALLATI O N
84"
W
(2134)
OPENING
HEIGHT
OPENING WIDTH
The unit can be installed next to an Designer refrigeration
model or another Designer wine storage model in a dual
installation. When installing two units side by side, the
opening width is the width of the two units added together.
A dual installation kit is required for this installation. If a dual
installation kit is not specified, a minimum 2" (51) filler strip is
required between the units.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero Customer
Care at 800-222-7820.
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
3/4" (19)
3/4" (19)
TYPICAL
TYPICAL
3 1/2" (89)
3 1/2" (89)
FINISHED
RETURN
FINISHED
RETURN
W
W
FRAMELESS
CABINETRY
FRAMED
CABINETRY
64 | Sub-Zero Customer Care 800.222.7820
FILLER
P R ES S -TO -O P EN I N S TALLATI O N
Column Models Only: For information regarding a press-toopen (handleless) design, refer to the guides section of any
Designer column or Designer wine column product page of
our website, subzero.com.
W INE S T O R AG E
Overall Dimensions
M ODEL B W-30
SPECIFICATIONS
26 3/16" (665)
30" (762)
STORAGE C A PAC ITY
BW-30
SH IPP IN G WEIGH T
BW-30
B OT T LE S *
146
LB ( K G )
445 (202)
*750 ml bottles.
84"
(2134)
73 3/4"
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
23 7/8" (606)
23 7/8"
(606)
17"
(432)
311/4"
(796)
2 3/8" (60)
Overall dimensions are based on the stainless steel model.
For flush inset applications, add 1/2" (13) to door clearance
dimensions.
subzero.com | 65
W INE S T O R AG E
Opening Dimensions
M ODEL B W-30 STANDARD INSTAL L ATION
24" (610)
OPENING
DEPTH
3/4" (19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
TOP VIEW
W
FRAMELESS
CABINETRY
3/4" (19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
83 3/4"
W
(2127)
OPENING
HEIGHT
OPENING WIDTH
SIDE VIEW
FILLER
W
FRAMED
CABINETRY
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit.
OPENING WIDTH
BW-30
W
29 1/2" (749)
If an 83" (2108) grille height is specified, the opening height
must be decreased by 7/8" (22). If an 88" (2235) grille height is
specified, the opening height must be increased by 4" (102).
If two units are installed side by side, refer to page 68 for
dual standard installations.
66 | Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
Opening Dimensions
M ODEL B W-30 FL USH INSE T INSTAL L ATION
26 3/16"
(665)
FLUSH
INSET
DEPTH
5 11/16" 3 1/2"
2 3/16"
(56)
(89)
(145)
FINISHED
RETURN
FINISHED
CLEATS
TOP VIEW
CLEAT
3/4" (19)
TYPICAL
W
FRAMELESS
CABINETRY
11/4"
1/4"
(6)
(32)
5 11/16" 3 1/2"
(89)
(145)
FINISHED
RETURN
SIDE VIEW
84"
W
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
CLEAT
FILLER
3/4" (19)
TYPICAL
W
FRAMED
CABINETRY
FRONT VIEW
NOTE: 3 1/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit with 3/4" (19) panel.
FLUSH INSET WIDTH
BW-30
W
Flush inset is available for overlay models only.
32" (813)
Dimensions assume a 3/4" (19) panel thickness.
If an 83" (2108) grille height is specified, the flush inset
height must be decreased by 7/8" (22). If an 88" (2235) grille
height is specified, the flush inset height must be increased
by 4" (102).
If two units are installed side by side, refer to page 69 for
dual flush inset installations.
subzero.com | 67
W INE S T O R AG E
Opening Dimensions
M ODEL B W-30 DUAL STANDARD INSTAL L ATI O N
24" (610)
OPENING
DEPTH
3/4" (19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
TOP VIEW
W
FRAMELESS
CABINETRY
3/4" (19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
83 3/4"
W
(2127)
OPENING
HEIGHT
OPENING WIDTH
SIDE VIEW
FILLER
W
FRAMED
CABINETRY
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit.
DUAL OPENING WIDTH
W
BW-30 and 30" Classic Model
59 3/4" (1518)
BW-30 and 36" Classic Model
65 3/4" (1670)
68 | Sub-Zero Customer Care 800.222.7820
A dual installation kit is required for this installation.
W INE S T O R AG E
Opening Dimensions
M ODEL B W-30 DUAL FL USH INSE T INSTAL LATI O N
26 3/16"
(665)
FLUSH
INSET
DEPTH
(56)
CLEAT
5 11/16" 3 1/2"
2 3/16"
3/4" (19)
(89)
(145)
FINISHED
RETURN
FINISHED
CLEATS
TOP VIEW
TYPICAL
W
FRAMELESS
CABINETRY
11/4"
1/4"
(6)
(32)
CLEAT
5 11/16" 3 1/2"
(89)
(145)
FINISHED
RETURN
84"
W
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
FILLER
3/4" (19)
TYPICAL
W
FRAMED
CABINETRY
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit with 3/4" (19) panel.
DUAL FLUSH INSET WIDTH
W
BW-30 and 30" Classic Model
62 1/4" (1581)
BW-30 and 36" Classic Model
68 1/4"
(1734)
Flush inset is available for overlay models only.
Dimensions assume a 3/4" (19) panel thickness. A dual installation kit is required for this installation.
subzero.com | 69
W INE S T O R AG E
Electrical Requirements
Locate the electrical supply within the shaded area shown
in the illustration for your specific model. For Designer (IW)
models, also refer to the chart. A separate circuit servicing
only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
ELECTRICAL LOCATION—DESIGNER
18" Model
6" (152)
24" Model
9 1/2" (241)
30" Model
12 1/2" (318)
If the unit will be connected to a home security system,
allow 36" (914) of excess wiring for proper connection.
IMPORTANT NOTE: For Designer and Undercounter models,
the electrical outlet must be positioned with the grounding
prong to the right of the thinner blades.
Installation must comply with all applicable electrical codes.
LEFT SIDE
OF OPENING
41/2"
(114)
A
4 1/4"
ELECTRICAL REQUIREMENTS
(108)
Electrical Supply
115 VAC, 60 Hz
Service
15 amp dedicated circuit
Receptacle
1/4" (6)
FLOOR
3-prong grounding-type
Designer models
LEFT SIDE
OF OPENING
7"
E
(178)
6"
(152)
2"
(51)
15 1/2"
(394)
3" (76)
75 1/2" (1918)
FROM FLOOR
FLOOR
Model UW-24
RIGHT SIDE
OF OPENING
Model BW-30
70 | Sub-Zero Customer Care 800.222.7820
A
W INE S T O R AG E
Plumbing Requirements
M ODEL IW-30CI
For model IW-30CI, locate the water supply line within the
shaded area shown in the illustration below. Connect the
water supply line to the house supply with an easily accessible shut-off valve. Do not use self‑piercing valves. The
water supply line must not interfere with installation of the
anti-tip bracket.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
1/4"
Water Supply
Pressure
OD copper, braided stainless
steel, or PEX tubing
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
WATER SUPPLY LOCATION
IW-30CI
36" (914)
A
6" (152)
RIGHT SIDE
OF OPENING
A
6" (152)
3" (76)
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
Water supply location
subzero.com | 71
W INE S T O R AG E
Custom Panels
Custom Panel—UW-24
For framed, overlay, Designer, and flush inset applications,
a custom door panel must be provided. Handle hardware
must also be provided for overlay, Designer, and flush inset
applications. Refer to the panel requirements and custom
panel dimensions charts for your specific model and design
application.
For model UW-24, the custom door panel will attach directly
to the door frame with screws through a series of pre-drilled
holes.
Do not install a solid panel on a glass door unit. A solid door
is available as a sales accessory (except model BW-30) and
must be installed if a solid panel is being specified. Service
may be required to install the door. Contact an authorized
Sub-Zero dealer for more information. Overall dimensions
are the same for glass and solid door panels.
PANEL REQUIREMENTS
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
Model UW-24FS has a finished stainless steel exterior that
is designed to be used in a freestanding application.
Refer to the charts below for panel requirements and
dimensions.
WEIGH T PER PAN EL
MAX
UW-24
10 lb (5 kg)
PAN EL TH IC KN ESS
M IN
5/8"
UW-24
(16)
O V ER LAY PAN EL D I M EN S I O N S
A
A
A
H
A
W
UW-24
PANEL DIMENSIONS
PAN EL
W
H
UW-24
23 3/4" (603)
30 1/16" (764)
STIL ES / RAIL S
Minimum
A
2 1/4" (57)
D O O R C LEAR A N C E
Model UW-24 can be installed flush with surrounding cabinetry. Depending on the thickness of the overlay door panel,
it may be necessary to install the unit 1/4" (6) beyond the
front surface of adjacent cabinetry to prevent interference
when the door is opened to 145°. Refer to the full-scale
template on page 83.
72 | Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
Custom Panel—Designer
For Designer (IW) models, custom door panels and handle
hardware must be provided. Refer to the Panel Requirements chart and Typical Panel Dimensions.
TY PI C AL PAN EL D I M EN S I O N S
Do not install a solid panel on the glass door unit. A solid
door is available as a sales accessory through an authorized
Sub-Zero dealer.
79 7/8"
49 3/8"
(2029)
(1254)
The thickness of the custom panel can vary. A minimum
5/8" (16) thick panel is required, but the thickness can be
increased provided it does not exceed the weight limit. The
depth of each Designer model is 24" (610). Allow for panel
thickness when planning the finished opening depth. Refer
to the full-scale template on page 57.
CAUTION
13 9/16"
(345)
16 11/16"
(424)
W
As reveals between cabinetry and the unit decrease,
severe finger pinching can occur while the door is
closing.
Column
Finish all sides of the custom panels. They will be visible
when the door/drawer is open.
D-style handles are recommended. Locate the door handle
near the edge of the panel opposite the hinge and centered
top to bottom. Locate drawer handles near the top edge
of each panel. Stainless steel tubular and pro handles are
avail­able through an authorized Sub-Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com.
W
Tall
Typical panel dimensions are based on an 84" (2134) finished
height, 4" (102) toe kick, and 1/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations.
Refer to the illustration for panel height and the chart below
for panel width.
PANEL WIDTH
MOD EL
18" Model
24" Model
30" Model
STIL ES / RAIL S
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
Door Frame (column)
Door Frame (tall)
Drawer Panel (tall)
PA N E L T H I C K N E S S
All Panels
MA X
35 lb (16 kg)
25 lb (11 kg)
15 lb (7 kg)
MIN
5/8"
(16)
Stiles
Top Rail
Bottom Rail (column)
Bottom Rail (tall)
W
17 3/4" (451)
23 3/4" (603)
29 3/4" (756)
M IN
3 1/4" (83)
7 3/4" (197)
9 1/2" (241)
4 1/2" (114)
D U AL I N S TALLATI O N
For dual installations, refer to the illustration for panel height
and the chart below for panel width.
PANEL WIDTH
MOD EL
18" Model
24" Model
30" Model
W
17 13/16" (452)
23 13/16" (605)
29 13/16" (757)
subzero.com | 73
W INE S T O R AG E
Custom Panel—Designer
D OO R PANEL HEIGHT
TO E K I C K C LEAR A N C E
The height of the custom door panel can extend beyond the
typical panel height, provided it does not exceed the weight
limit. Refer to the illustration below.
The height of the toe kick area can extend beyond the
typical toe kick height, provided it does not exceed the
dimensions in the illustration below. Toe kick heights from
2" (51) to 3 7/8" (98) require a reduced toe kick accessory
available through an authorized Sub-Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com. For questions regarding the installation, call Sub‑Zero Customer Care at 800-222-7820.
1 3/4"
(45)
A DECORATIVE VALANCE
CANNOT EXTEND
BEYOND THIS PLANE
1/8" (3)
DOOR
PANEL
84"
24" (610)
(2134)
TO BACK OF UNIT
HINGE**
VENTED
LOUVERS
24" (610)
TO BACK OF UNIT
HINGE
DOOR
PANEL
1 1/8" (29)
MAX
TOE KICK
ADJUSTMENT
2" (51)*
TO
6" (152)
FROM
FLOOR
Upper valance (side view)
*2" (51) to 3 7/8" (98) requires sales accessory.
**Column models only.
Toe kick (side view)
74 | Sub-Zero Customer Care 800.222.7820
A DECORATIVE TOE KICK
CANNOT EXTEND
BEYOND THIS PLANE
W INE S T O R AG E
Custom Panel—BW-30
F R AMED
FR AM ED PAN EL D I M EN S I O N S
The framed application is an overlay model with framed
design features. It is not a separate model.
H
A
1/4"
(6), a filler material
If the custom panel is thinner than
must be added to achieve a proper fit. If the panel is thicker
than 1/4" (6), rout an edge around the panel or mount the
custom panel on a sheet of 1/4" (6) thick material and insert
into the channel.
Routing, recessing, and optional extended handles may be
required for finger clearance. Refer to the full-scale template
on page 84.
A
A
H
A
W
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
Door
Grille (optional)
PA N E L T H I C K N E S S
Framed
MA X
75 lb (34 kg)
13 lb (6 kg)
MIN
1/4"
(6)
BW-30
PANEL DIMENSIONS
FRAMED PAN EL
Door
Grille (optional)
STIL ES / RAIL S
Minimum
W
H
29 3/4" (756)
29 3/4" (756)
69 9/16" (1767)
8 15/16" (227)
A
3 3/16" (81)
subzero.com | 75
W INE S T O R AG E
Custom Panel—BW-30
O VER LAY
O VER LAY PA N EL D I MEN S I O N S
Overlay panels are typically created by combining a 3/4" (19)
custom panel, a .10" (3) spacer panel, and a 1/4" (6) backer
panel. Refer to the illustrations below.
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
MA X
Door
Grille
H
A
A
A
H
75 lb (34 kg)
13 lb (6 kg)
PA N E L T H I C K N E S S
MIN
5/8"
Overlay
(16)
A
W
CUSTOM
PANEL
SPACER PANEL
SPACER
PANEL
BW-30
OVERLAY PANELS
CUSTOM PANEL
D OOR
BACKER PANEL
BACKER
PANEL
TRIM
DOOR FRAME
GLASS
Overlay Panel
Spacer Panel
Backer Panel
GRIL L E
5/16" (8) min
1/8"
(3)
Panel assembly (cross section)
3/4"
(19)
typical
.10" (3) 1/4" (6)
Panel assembly (rear view)
Overlay Panel
Spacer Panel
Backer Panel
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
STIL ES / RAIL S
Minimum
A
3 1/4" (83)
*Panel height may be increased by 7/16" (11) to hide upper main frame. Also
refer to Classic panel configurator at subzero.com/trade/panels.
Grille panel dimensions are for standard 84" (2134) overall unit height. For 83"
(2108) height, subtract 1" (25) from grille panel height dimensions and for 88"
(2235) height, add 4" (102). A specific panel grille must be ordered for an 83"
or 88" overall unit height.
76 | Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
Custom Panel—BW-30
F LUS H INS ET
FLU S H I N S ET PA N EL D I MEN S I O N S
The flush inset application is an overlay model with flush
inset panels. It is not a separate model.
H
A
The flush inset design allows custom panels to be installed
flush with adjacent cabinets. Similar to overlay, flush inset
panels are typically created by combining a 3/4" (19) custom
panel, a .10" (3) spacer panel, and a 1/4" (6) backer panel.
Refer to the illustrations for overlay panels on the previous
page.
A
For flush inset panels thicker than 3/4" (19), a 90° door stop
may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 87.
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
Door
Grille
PA N E L T H I C K N E S S
Flush Inset
A
H
A
W
BW-30
MA X
75 lb (34 kg)
13 lb (6 kg)
MIN
5/8"
(16)
FLUSH INSET PANELS
D OOR
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
STIL ES / RAIL S
Minimum
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
A
3 3/4" (95)
Grille panel dimensions are for standard 84" (2134) overall unit height. For
83" (2108) height, subtract 1" (25) from grille panel height dimensions and for
88" (2235) height, add 4" (102). A specific panel grille must be ordered for an
83" or 88" overall unit height.
subzero.com | 77
5/16" (8)
W INE S T O R AG E
5/8"
(16)
TOP VIEW
TOP VIEW
CABINETRY
DOOR / DRAWER / GRILLE
1/2" (13)
5/16"
(8) 5/32"
(4)
GRILLE
Custom Panel—BW-30
BACKER
F LUS H INS ET PA SPACER
NE L OFFSE T
CABINETRY
The illustrations provide
offsets and reveals for model
FLUSHpanel
INSET PANEL
BW-30 in a flush inset application.
Refer to the chart below
5/16" (8)
1/2"
for reference to the illustrations.
(13)
5/8"
(16)
PANEL OFFSET
DOOR
1/8"
5/16" (3)
(8)
GRILLE
DOOR
A
Grille Top
B
Grille Bottom / Door Top
C
Door Bottom
D
1/2" (13)
TOP VIEW
DOOR
CABINETRY
1/4" (6)
GRILLE
REVEAL
5/16" (8)
5/8"
(16)
5/16"
(8) 3/32"
(2)
SIDE VIEW
1/8" (3)
GRILLE
CABINETRY
5/32"
5/16" (4)
(8)
SIDE VIEW
1/4" (6)
SIDE VIEW
REVEAL
DOOR
GRILLE
5/16"
(8) 5/32"
(4)
5/16"
(8)
1/2" (13)
1/2" (13)
3/32"
5/16" (2)
(8)
1/8"
5SIDE
/16" (3)
VIEW
(8)
Illus. C
5/16"
GRILLE
(8) 3/32
"
(2)
DOOR
SIDE VIEW
Illus.
D
DRAWER
SIDE VIEW
5/16"
(8) 3/32"
(2)
5/16" (3)
(8)
DOOR /
DRAWER
5/8" (16)
DRAWER
DOOR
Illus. B
DOOR
GRILLE
DOOR
SIDE VIEW1/8"
5/16" (8)
1/2"
(13)
CABINETRY
1/8"
5/16" (3)
(8)
1/2" (13)
FLUSH INSET PANEL
Illus. A
1/2" (13)
3/32"
5/16" (2)
(8)
5/16" (8)
1/8" (3)
BACKER
SIDE VIEW
SPACER
TOP VIEW
CABINETRY
DOOR / DRAWER / GRILLE
IL L U S
Door / Grille Sides
1/2"
(13)
3/32" (4) DOOR
5/32" (2) DRAWER
5/8" (16)
DOOR
5/32"
5/16" (4)
(8)
5/16"
(8) 5/32"
(4)
1/2
3/32"
5/16" (2)
(8)
SIDE VIEW
SIDE VIEW
DOOR /
DRAWER
DOOR
5/8" (16)
DRAWER
5/32"
5/16" (4)
(8)
SIDE VIEW
5/16"
(8)
5/16"
(8) 3/32"
(2)
DOOR
SIDE VIEW
DRAWER
3/32" (4) DOOR
5/32"5/(2)
8" (16)
DRAWER
5/16"
(8)
5/32"
5/16" (4)
(8)
SIDE VIEW
78 | Sub-Zero Customer Care 800.222.7820
DOOR /
DRAWER
SIDE VIEW
3/32" (
5/32" (2
W INE S T O R AG E
Custom Panel—BW-30
D U AL FLU S H I N S ET PA N EL D I MEN S I O N S
D U AL INS TALLATIONS
A dual installation kit may be required if two models BW-30
or a model BW-30 and a Classic unit are installed side by
side. Installations without a custom filler strip require a dual
installation kit. If a dual installation kit is not specified, a
2" (51) filler strip is recommended between the units. Dual
installations without a filler strip can only be accomplished
using two 84" (2134) units with opposite hinges. Refer to the
illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero Customer
Care at 800-222-7820.
For dual standard installations, panel dimensions are the
same as for single installations. Refer to the chart on page
76. Panel dimensions and offsets for dual flush inset installations are listed on the following pages.
H
A
A
A
H
A
W
BW-30
DUAL FLUSH INSET PANELS
D OOR
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
STIL ES / RAIL S
Minimum
A
3 3/4" (95)
Grille panel dimensions are for standard 84" (2134) overall unit height.
WITHOUT FILLER STRIP
Opposite hinges
FILLER STRIP
Same side hinges
subzero.com | 79
W INE S T O R AG E
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
BACKER
SPACER
DOOR
CABINETRY
DOOR
TOP VIEW
FLUSH INSET PANEL
5
/16" (8)
Custom Panel—BW-30
D U AL F LUS H IN SE T
1/8" (3)
BACKER
SPACER
BACKER
CABINETRY
SPACER
The illustrations provide panel offsets and reveals for
model
FLUSH
INSET PANEL
BW-30 in a dual flush inset application. Refer to the chart5
/16" (8)
below for reference to the illustrations.
PANEL OFFSET
IL L U S
Door (hinge) / Grille Sides
A
Door (handle) Sides
B
Grille Top
1/4" (6) CABINETRY
CABINETRY
Door Bottom
BACKER
GRILLE
E
5/8"
(16)
TOP VIEW
5/16" (8)
DOOR
1/8" (3)
5/16" (8)
DOOR
DOOR
1
/8" (3)
1/4" (6)
DOOR
1/4" (6)
REVEAL
REVEAL
FLUSH INSET PANEL
5/16" (8)
5/8"
(16)
1/2"
(13)
5/16" (8)
1/8" (3)
5/16" (8)
1/8" (3)
1/4" (6)
1/4" (6)
REVEAL
REVEAL
5/16"
(8) 5/32"
(4)
GRILLE
Illus. A
1/8"
5/16" (3)
(8)
Illus. B
1/2" (13)
CABINETRY
CABINETRY
DOOR 1
/2" (13)
SIDE VIEW
1/2"
(13)
CABINETRY
5/8"
SPACER
(16)
DOOR
DUAL
TRIM
5/16" (8)
1/2"
(13)
DOOR
DOOR
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
D
1/2" (13)
DOOR
REVEAL
TOP VIEW
C
Grille Bottom / Door Top
TOP VIEW
DOOR / DRAWER / GRILLE
5/16" (8)
1/2"
(13)
5/8"
PANE L (16)
OFFSE T
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
GRILLE
1/8"
5/16" (3)GRILLE
(8)
3/32"
5/16" (2)
(8)
CABINETRY
1/2" (13)
1/8"
/16" (3)
SIDE VIEW
5
DOOR /
DRAWER
5/16"
(8) 3/32"
(2)
DOOR
1/8"
5/16
" (3)
SIDE
VIEW
(8)
Illus. C
5/16"
(8) 5/32GRILLE
"
(4)
1/2" (13)
(8)
1/2" (13)
GRILLE
SIDE VIEW
GRILLE
DOOR
3/32
GRILLE
"
5/16" (2)
(8)
SIDE VIEW
1/2
5/16"
32""
(8) 53//32
5/16" (4)
(2)
(8)
SIDE VIEW
1/2
DOOR
Illus. D
5/16"
(8) 5/32"
(4)
SIDE VIEW
3/32"
5/16" (2)
(8)
SIDE VIEW
DOOR
5/8" (16)
DRAWER
5/32"
5/16" (4)
(8)
5/16"
(8)
5/16"
(8) 3/32"
(2)
DOOR
SIDE VIEW
DOOR
SIDE
5 VIEW
/8" (16)
DRAWER
5/DRAWER
Illus.
32E
"
5/16" (4)
(8) DOOR
SIDE VIEW
DRAWER
5/16"
(8) 3/32"
(2)
3/32" (4) DOOR
5/32" (2) DRAWER
5/8" (16)
5/8" (16)
SIDE VIEW
DOOR /
DRAWER
5/16"
(8) DOOR /
DRAWER
5/16"
(8) 35//32
32""
5/16" (2)
(4)
(8)
SIDE VIEW
3/32" (4) DOOR
5/32" (2)SIDE
DRAWER
VIEW
5/16"
(8)
3/32"
5/32
5/16
" (2
"
(8)
5/32"
5/16" (4)
(8)
SIDE VIEW
80 | Sub-Zero Customer Care 800.222.7820
DOOR /
DRAWER
SIDE VIEW
3/32" (
5/32" (2
W INE S T O R AG E
Custom Panel—BW-30
Standard Handles
S I DE PANEL
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
The custom side panel must be a minimum of 24" (610) deep
and 1/2" (13) thick. Routing will be necessary for the side
panel to fit flush against the side of the unit. Refer to the
illustrations below.
When installing model BW-30 with a custom side panel, an
accessory kit is required. Stainless steel and white enamel
side panels are available for an 84" (2134) finished height
through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our website, subzero.com.
Refer to the chart below for standard handle lengths for
wine storage models.
HANDLE LENGTH
TU BU L A R
UW-24 Door
24 1/4"
IW-18, IW-24, IW-30 Door
50 1/8"
(616)
(1273)
PRO
22 1/4"
48 3/8"
(572)
(1229)
IW-30R Door
33 1/4" (845)
31 1/2" (800)
IW-30R Drawer
24 1/4" (616)
22 1/2" (572)
63 7/8" (1622)
45 3/16" (1147)
BW-30 Door
24" (610)
FRONT
OF SIDE
PANEL
1" (25)
1 7/8" (48)
1/8" (3)
1/2" (13)
ROUT TO 1/8" (3)
1 7/8"(48)
1" (25)
84"
MAIN
FRAME
SIDE PANEL
ROUTING
(2134)
Routing detail
4" (102)
OPTIONAL
TOE KICK
CUT-OUT
2 5/8"
(67)
Side panel dimensions
subzero.com | 81
W INE S T O R AG E
Wine Rack Wood Facing
F ULL-S CALE T E MPL ATE
WOOD FACING WIDTH
The natural cherrywood facing on wine storage racks can
be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale
template below for the profile dimensions of the wood
facing and the chart for the width.
1/2"
(13)
1/4"
(6)
27/32"
7/64"
(3)
(21)
7/32" (6)
11/2"
(38)
23/64"
(9)
9/16"
(14)
5/64"
(2)
Wine rack wood facing profile
82 | Sub-Zero Customer Care 800.222.7820
W
UW-24, UW-24FS
19 1/2"
IW-18
11 5/8" (295)
IW-24
17 5/8" (448)
IW-30, IW-30R, IW-30CI
23 5/8" (600)
BW-30
(495)
24 9/16" (624)
W INE S T O R AG E
Door Clearance—UW-24
F ULL-S CALE T E MPL ATE
To allow for a 145° door opening, the unit should extend
a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however,
there is potential for interference with the panel if the
door is opened past 90°.
UNDERCOUNTER
UNIT
ADJACENT
CABINETRY
DOOR CLOSED
1/2"
(13)
3/4" (19) DOOR PANEL
1/4" (6)
1/8" (3)
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
0"
1" (25)
SCALE
145° door opening (top view)
subzero.com | 83
W INE S T O R AG E
Framed Panel—BW-30
F ULL-S CALE T E MPL ATE
OPTIONAL EXTENDED
FULL-LENGTH HANDLE
STANDARD
FULL-LENGTH HANDLE
2"
1"
(51)
(25)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
1/2" (13) PANEL
1/4" (6) FRAMED PANEL
DOOR
Framed panel thickness
84 | Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
Overlay | Flush Inset Panels—BW-30
F ULL-S CALE T E MPL ATE
Overlay and flush inset panels must be a minimum of 5/8"
(16) thick to support mounting the handle. Panel thickness
does not include the backer and spacer panels. Mount the
handle close to the opening edge of the door.
DEPTH OF TUBULAR
AND PRO HANDLES
1"
2"
(25)
(51)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
.10" (3) SPACER PANEL
1/4" (6) BACKER PANEL
DOOR
Overlay and flush inset panel thickness
subzero.com | 85
W INE S T O R AG E
Overlay Application—BW-30
F ULL-S CALE T E MPL ATE
237/8" (606)
TO REAR OF UNIT
OVERALL WIDTH OF UNIT
0" (0)
1/4" (6)
1/2" (13)
3/4" (19)
1" (25)
11/4" (32)
11/2" (38)
13/4" (44)
2" (51)
21/4" (57)
21/2" (63)
23/4" (70)
3" (76)
31/4" (83)
31/2" (89)
1" (25) THICK
PANEL
3/4" (19) THICK
OVERLAY PANEL
(TYPICAL)
1/4" (6) BACKER
PANEL
0"
1" (25)
SCALE
90° door opening (top view)
86 | Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
Flush Inset Application—BW-30
F ULL-S CALE T E MPL ATE
24" (610)
TO BACK WALL
For panels thicker than 3/4" (19), a 90° door stop may be
required to prevent interference with adjacent cabinets.
1 1/4" (32)
2 3/16" (56)
ASSUMES
3/4" (19)
FLUSH INSET
PANEL
THICKNESS
1" (25) THICK
PANEL
3/4" (19) THICK
FLUSH INSET PANEL
(TYPICAL)
1/4" (6) BACKER
PANEL
0"
1" (25)
SCALE
110° door opening (top view)
subzero.com | 87
W INE S T O R AG E
FILLER STRIP
11/4" (32)
APPROX PROFILE OF
STAINLESS STEEL WRAPPED
DOOR AND HANDLE
Dual Standard Installation—BW-30
F ULL-S CALE T E MPL ATE
Typical framed, overlay, or stainless steel dual installation
with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.
0"
1" (25)
SCALE
Dual standard installation (top view)
88 | Sub-Zero Customer Care 800.222.7820
DOOR
CLOSED
DOOR
OPEN 110°
W INE S T O R AG E
FILLER STRIP
1 1/2" (38)
1/2" (13)
PROFILE OF 3/4" (19) FLUSH INSET PANEL
AND TUBULAR HANDLE
Dual Flush Inset Installation—BW-30
DOOR
CLOSED
DOOR
OPEN 110°
F ULL-S CALE T E MPL ATE
Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90°
door stop.
0"
1" (25)
SCALE
Dual flush inset installation (top view)
subzero.com | 89
U N D E R C O U N T E R R E F R I G E R AT I O N
90 | Sub-Zero Customer Care 800.222.7820
U N DER CO UNT E R RE FRIGE RATION
Undercounter Refrigeration
Sub-Zero Undercounter refrigeration is a helpful addition
to a master suite, bar, home office, or media room. In the
kitchen, a high-volume ice maker is a must for entertaining.
The design flexibility of these compact yet roomy units
makes them all the more welcome in any room or outdoor
kitchen. They are ready to be fitted with a custom panel and
handle or can be ordered with a stainless steel panel and
handle.
U N D ER C O U N TER MO D ELS
UC-24R
UC-24BG
UC-24C(I)
UC-24RO
I C E MAK ER MO D ELS
UC-15I(P)
UC-15I(P)O
subzero.com | 91
U N DER CO UNT E R RE FRIGE RATION
Overall Dimensions
U N DER CO UNT E R
I C E MAK ER
23 7/8" (606)
14 3/4" (375)
24" (610)
23" (584)
33 5/8"
34"
(854)
(864)
4" (102)
4" (102)
18"
(457)
25 3/8"
(645)
6"
(152)
26" (660)
8"
(203)
SPECIFICATIONS
I NT E R I O R C A PA C I T Y—CU FT (L )
UC-24R, UC-24RO
UC-24BG
UC-24C(I)
SPECIFICATIONS
RE FR
5.7 (161)
6.0 (170)
3.6 (102)
FRZR
1.1 (31)
SH I P P I N G W E I G H T
L B (KG )
24" Model
130 (59)
Refer to page 99 for door clearance information.
92 | Sub-Zero Customer Care 800.222.7820
STORAGE C A PAC ITY
LB ( K G )
UC-15I(P), UC-15I(P)O
26 (12)
SH IP P IN G WEIGH T
LB ( K G )
Ice Maker
100 (45)
Model UC-15I overall dimensions do not include the panel
or handle.
U N DER CO UNT E R RE FRIGE RATION
Opening Dimensions
D U AL I N S TALLATI O N
U N DER CO UNT E R
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom filler strip
require a dual installation kit. If a dual installation kit is not
specified, a 2" (51) filler strip is recommended between the
units. Dual installations without a filler strip can only be
accomplished using two units with opposite hinges. Refer to
the illustrations below.
24" (610)
OPENING
DEPTH
TOP VIEW
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero Customer
Care at 800-222-7820.
34 1/2"
W
(876)
OPENING
HEIGHT
OPENING WIDTH
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
3/4" (19)
3/4" (19)
TYPICAL
TYPICAL
3 1/2" (89)
3 1/2" (89)
FINISHED
RETURN
FINISHED
RETURN
W
WITHOUT FILLER STRIP
FILLER STRIP
FILLER
Opposite hinges
Same side hinges
W
FRAMELESS
CABINETRY
FRAMED
CABINETRY
OPENING WIDTH
W
24" Model
24" (610)
Ice Maker
15 1/4" (387)
DUAL OPENING WIDTH
Two 24" Models
W
48 1/8"
(1222)
Dual installation kit required.
subzero.com | 93
U N DER CO UNT E R RE FRIGE RATION
Electrical Requirements
Locate the electrical supply within the shaded area shown in
the illustrations below. A separate circuit servicing only this
appliance is required.
ELECTRICAL REQUIREMENTS
IMPORTANT NOTE: For 24" models, the electrical outlet
must be positioned with the grounding prong to the right of
the thinner blades.
Receptacle
IMPORTANT NOTE: For outdoor models UC-24RO and
UC-15I(P)O, a ground fault circuit interrupter (GFCI) is
required to reduce the risk of electrical shock. A GFCI is not
recommended for use with other Undercounter models and
may cause interruption of operation.
Installation must comply with all applicable electrical codes.
LEFT SIDE
OF OPENING
2"
(51)
LOCATE
ELECTRICAL
SUPPLY IN
ADJACENT
CABINET
15 1/2"
(394)
3" (76)
E
FLOOR
24" Models
Ice maker
94 | Sub-Zero Customer Care 800.222.7820
E
Electrical Supply
Service
115 VAC, 60 Hz
15 amp dedicated circuit
3-prong grounding-type
U N DER CO UNT E R RE FRIGE RATION
Plumbing Requirements
Locate the water supply line within the shaded area shown
in the illustrations below. Connect the water supply line to
the house supply with an easily accessible shut-off valve
between the supply and the unit. Do not use self‑piercing
valves. A saddle valve kit is avail­able through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com.
IMPORTANT NOTE: A reverse osmosis system can be used
provided there is constant water pressure supplied to the
unit at all times as indicated in the chart below. A copper
line is not recommended for this application.
I C E MAK ER D R A I N
Ice maker models can be ordered with or without a drain
pump. Models without a pump will drain water by gravity.
A drain must be installed.
The drain and inlet water tubes must be plumbed before
connecting to the ice maker. For the gravity drain, horizontal
drain lines must have a 1/4" (6) per 12" (305) fall.
An air gap will likely be required between the unit and drain.
A stand pipe with a trap below is acceptable for the drain.
PLUMBING REQUIREMENTS
1/4"
Water Supply
OD copper, braided stainless
steel, or PEX tubing
Pressure (UC-24CI)
20–100 psi (1.4–6.9 bar)
Pressure (UC-15I)
20–80 psi (1.4–5.5 bar)
Excess Line for Connection
36" (914)
LEFT SIDE
OF OPENING
8"
1/2"
(13)
2"
(51)
(203)
24" (610)
ROUGH
OPENING
DEPTH
LOCATION OF
WATER LINE
15 1/2"
(394)
3" (76)
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
Model UC-24CI
TOP VIEW
Ice maker
15 1/4" min (387)
ROUGH
OPENING WIDTH
341/2" (876)
ROUGH
OPENING
HEIGHT
33 5/8" (854)
POSITION OUTLET
WITH GROUNDING
PRONG ON RIGHT
LOCATE
ELECTRICAL
WITHIN
SHADED AREA
MINIMUM
HEIGHT
REQUIRED
4" (102)
FRONT VIEW
subzero.com | 95
U N DER CO UNT E R RE FRIGE RATION
Custom Panel
For overlay Undercounter models, a custom door panel and
handle hardware must be provided. Refer to the charts for
panel requirements and dimensions.
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
UC-24R, UC-24C(I)
UC-24BG
UC-15I(P)
PA N E L T H I C K N E S S
All Panels
96 | Sub-Zero Customer Care 800.222.7820
MA X
20 lb (9 kg)
10 lb (5 kg)
15 lb (7 kg)
MIN
5/8"
(16)
M O D EL U C -2 4 B G
For model UC-24BG, the custom door panel will attach
directly to the door frame with screws through a series of
pre-drilled holes.
Do not install a solid panel on a glass door unit. A solid door
is available as a sales accessory and must be installed if a
solid panel is specified. Service may be required to install
the door. Contact an authorized Sub-Zero dealer for more
information. Overall dimensions are the same for glass and
solid door panels.
U N DER CO UNT E R RE FRIGE RATION
Custom Panel
Standard Handles
O VER LAY PANEL DIME NSIONS
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
A
H
A
A
H
Refer to the chart below for standard handle lengths for
Undercounter models.
A
W
UC-24R, UC-24C(I),
UC-15I(P)
W
UC-24BG
HANDLE LENGTH
TU BU L A R
Undercounter
24 1/4"
Outdoor Model
PRO
(616)
22 1/2"
(572)
NA
15 11/16"
(399)
PANEL DIMENSIONS
MODEL
24" Model
Ice Maker
ST I L E S / R A I L S
UC-24BG
W
H
23 3/4" (603)
15" (381)
30 1/16" (764)
30 3/8" (772)
A
2 1/4" (57) min
D O O R CLEAR AN CE
Undercounter models can be installed flush with surrounding cabinetry. Depending on the thickness of the
custom door panel, it may be necessary to install the unit
1/4" (6) beyond the front surface of adjacent cabinetry to
prevent interference when the door is opened to 145°. Refer
to the full-scale template on page 99.
subzero.com | 97
U N DER CO UNT E R RE FRIGE RATION
Wine Rack Wood Facing
F ULL-S CALE T E MPL ATE
WOOD FACING WIDTH
The natural cherrywood facing on wine storage racks can
be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale
template below for the profile dimensions of the wood
facing and the chart for the width.
1/2"
W
UC-24BG
19 1/2"
UC-24C(I)
19 1/2" (495)
(495)
5/8"
(13)
(16)
7/64" (3)
1/4"
(6)
27/32"
7/64"
(3)
(21)
11/2"
(38)
27/32"
(21)
7/32" (6)
23/64"
23/64"
(9)
9/16"
(14)
IW-18, IW-24,
IW-30, IW-30R
(9)
9/16"
5/64"
(2)
(14)
5/64"
(2)
424G, UW-24, 424FSG
UW-24FS, WS-30, BW-30
Wine rack wood facing profile
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &
Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.
All other trademarks are property of their respective owners in the United States and other countries.
98 | Sub-Zero Customer Care 800.222.7820
U N DER CO UNT E R RE FRIGE RATION
Door Clearance—Undercounter
F ULL-S CALE T E MPL ATE
To allow for a 145° door opening, the unit should extend
a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however,
there is potential for interference with the panel if the
door is opened past 90°.
UNDERCOUNTER
UNIT
ADJACENT
CABINETRY
DOOR CLOSED
1/2"
(13)
3/4" (19) DOOR PANEL
1/4" (6)
1/8" (3)
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
0"
1" (25)
SCALE
145° door opening (top view)
subzero.com | 99
Sub-Zero Residential Limited Warranty
FOR RESIDENTIAL USE
FULL TWO YEAR WARRANTY*
For two years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be
performed by Sub-Zero Factory Certified Service, unless otherwise specified by Sub-Zero, Inc. Service
will be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero Factory Certified Service, unless
otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.
LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY
For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts
that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all
connecting tubing. If the owner uses Sub-Zero Factory Certified Service, the service provider will repair or
replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certified service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or
replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certified service
or other sources.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fifty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero Factory Certified Service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the Support & Service section of our website,
subzero.com, email us at customerservice@subzero.com or call 800-222-7820.
*Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
*Replacement water filters and air purification cartridges are not covered by the product warranty.
Sub-Zero Outdoor Limited Warranty*
FOR RESIDENTIAL USE
FULL ONE YEAR WARRANTY**
For one year from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be
performed by Sub-Zero Factory Certified Service, unless otherwise specified by Sub-Zero, Inc. Service
will be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero Factory Certified Service, unless
otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fifty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero Factory Certified Service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the Support & Service section of our website,
subzero.com, email us at customerservice@subzero.com or call 800-222-7820.
*Product must be approved for outdoor use, designated by model and serial number.
**Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
**Replacement water filters are not covered by the product warranty.
SUBZERO.COM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising