Dwyer | Series 1000E | Instruction manual | Dwyer Series 1000E Instruction Manual

Dwyer Series 1000E Instruction Manual
Bulletin IN-100E
Series 1000E Diaphragm Operated Pressure Switches
Installation and Operating Instructions
18˝ [457.2 MM]
LEADS FOR
SPLICING
(2) Ø17/64
[6.75]
MOUNTING
HOLES
ADJUSTING
WHEEL
SAFETY STOPS
DO NOT ALTER
READ
PSIG
Ø2-11/32
[59.53]
5-1/4
[133.35]
INCREASE
1-3/8
[34.93]
Series 1000E explosion-proof also available in 1000EH explosion-proof,
hermetically sealed switch assembly.
This control is operated by a negative rate Bellville spring-augmented
diaphragm.
Location and Mounting
Select a location recommended by the equipment manufacturer. Use
the two (2) lugs on the case to mount the control on a panel or smooth
wall surface, or mount directly by the pressure connection.
The control is not position sensitive and may be mounted in any position.
However, vertical is preferred when there is a possibility of sludge
accumulation or condensed water freezing in the pressure chamber.
Pressure Connection
The pressure connection is a standard female 1/4″ NPT taper pipe
thread. Pipe thread sealant tape or pipe thread sealant should be used
to assure a pressure-tight joint. When used on steam, a pigtail siphon
and Type 3 (FEP) diaphragm should be used.
Wiring
Wire in accordance with local electrical codes or equipment
manufacturer’s instructions. Use a short piece of BX between rigid
conduit and control so that control will not be subject to the stress of
conduit expansion and contraction. Electrical ratings are shown on the
label inside the adjusting wheel chamber.
DO NOT OVERLOAD
1/2 NPT
CONDUIT
THREAD
8.5
[215.90]
3-1/4
[82.55]
3-3/4 [95.25]
4-3/8 [111.13]
2-3/4
[69.85] 1/4 NPT
PRESSURE
CONNECTION
SPECIFICATIONS
Wetted Materials: Aluminum pressure chamber with polyimide
diaphragm or 316 SS pressure chamber with FEP diaphragm.
Temperature Limits: -30 to 170°F (-35 to 77°C).
Enclosure Rating: Explosion-proof, UL listed for Class 1, Groups A, B,
C and D; Class II, Groups E, F and G.
Switch Type: SPDT snap switch. Hermetically sealed optional.
Electrical Rating: 15A @ 125/250/480 VAC resistive; 0.5A @ 125
VDC, 0.25A @ 250 VDC.
Wiring Connections: 18 AWG, 18˝ (460 mm) color-coded leads: N.O.
(yellow), N.C. (black) and common (red).
Conduit Connection: 1/2˝ male NPT.
Process Connection: 1/4˝ female NPT.
Mounting Orientation: Any position.
Set Point Adjustment: Internal thumbwheel.
Weight: 3 lb (1.4 kg).
Deadband: See chart
Agency Approvals: CE, UL.
Note: When used on steam, a pigtail siphon and Type 3 (FEP)
diaphragm should be used. Maximum case ambient temperature: 170°F
(76.7°C).
Setting Operating Point
Remove the transparent cover over the adjusting wheel. Move the
wheel by hand to the desired pressure on the vertical scale. If the
adjusting wheel is difficult to move, a small screwdriver inserted in the
adjusting wheel arms will provide extra leverage. Safety stops are
provided at the top and bottom of the scale to prevent setting beyond the
control’s range. DO NOT alter. Dial markings are for the High operating
point. Switch will reset at a lower pressure. Dial markings are a guide for
setting. Actual setting should be checked with a good pressure gage.
Warning: A failure resulting in injury or damage may be caused by overpressures, excessive vibration or pressure pulsation, excessive
temperature, corrosion of pressure-containing parts and movement
assembly, electrical overload or other misuse.
MERCOID DIVISION
DWYER INSTRUMENTS, INC.
P.O. BOX 258 • MICHIGAN CITY, INDIANA 46360 U.S.A.
Phone: 219/879-8000
Fax: 219/872-9057
www.dwyer-inst.com
e-mail: info@dwyermail.com
Range No. psig (bar)
3
5-40 (0.35 - 2.76)
4
10-70 (0.69 - 4.82)
5
25 - 200 (1.72 - 13.78)
6
50 - 350 (3.45 - 24.12)
7
75 - 550 (5.17 - 37.90)
8
100 - 900 (6.89 - 62.01)
9
200 - 1400 (13.78 - 96.46)
Operating Rages/Deadband
Approx. Deadband (fixed)* psig (bar)
2.5 (0.17)
5 (0.34)
10 (0.69)
18 (1.2)
36 (2.5)
60 (4.1)
90 (6.2)
*Deadband is 10% larger when using 316SS diaphragm.
Electrical Rating
Code No. Switches Action
1 Snap SPDT
J
Note (2) Resistive
Max.
3000
3000
3000
3000
3000
3000
3000
press. without bursting psig (bar)
(206.7)
(206.7)
(206.7)
(206.7)
(206.7)
(206.7)
(206.7)
Horse Power
DC
AC
250V
125V 250V 480V 125V
125V 250V 125V 250V
15A 15A 15A 0.5A (2) 0.25A (2) 1/8
NA
1/4
NA
AC Capacity
DC Capacity
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising