Razor | Power Core E100 Electric Scooter | Owner's Manual | Razor Power Core E100 Electric Scooter Owner's Manual

Razor Power Core E100 Electric Scooter Owner's Manual
ELECTRIC HUB MOTOR SCOOTER
NOTE: The unit must be traveling at least 3 mph (5 km/h) before motor will engage.
Kick start to at least 3 mph (5 km/h) while applying throttle to engage motor.
OWNER’S MANUAL
Read and understand this entire manual before allowing
child to use this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 19 character product I.D. code with you
before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
CONTENTS
Safety Warnings............................................................................................... 1
Before You Begin.............................................................................................. 2
Assembly and Set-Up....................................................................................... 3
Charging the Battery and Pre-Ride Checklist................................................... 4
Usage and Repair and Maintenance................................................................ 5
Repair and Maintenance Cont’d....................................................................6-7
Troubleshooting Guide...................................................................................... 8
Power Core E100 Electric Scooter Parts........................................................... 9
Warranty and Contact Information................................................................. 11
SAFETY WARNINGS
Ride defensively. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Be careful to avoid
pedestrians, skaters, skateboards, scooters, bikes, children or animals who
may enter your path, and respect the rights and property of others.
The electric scooter is intended for use on flat, dry surfaces, such as
pavement or level ground, without loose debris, such as sand, leaves, rocks or
gravel. Wet, slick, bumpy, uneven or rough surfaces may impair traction and
contribute to possible accidents. Do not ride your scooter in mud, ice, puddles
or water. Watch out for potential obstacles that could catch your wheel or
force you to swerve suddenly or lose control. Avoid sharp bumps, drainage
grates, and sudden surface changes.
Do not attempt or do stunts or tricks on your electric scooter. The scooter is
not made to withstand abuse from misuse, such as jumping, curb grinding
or any other type of stunts. Racing, stunt riding, or other maneuvers also
enhance risk of loss of control, or may cause uncontrolled rider actions
or reactions.
Never allow more than one person at a time to ride the scooter.
Do not ride at night or when visibility is limited.
Never use near steps or swimming pools.
Do not allow hands, feet, hair, body parts, clothing, or similar articles to come
in contact with moving parts or wheels while the motor is running.
Do not touch hot brakes or electric motor when in use or immediately
after riding.
Never use headphones or a cell phone to talk or text when riding.
Never hitch a ride with a vehicle.
Do not ride your scooter in wet or icy weather and never immerse the scooter
in water, as the electrical and drive components could be damaged by water
or create other possibly unsafe conditions. Never risk damaging surfaces,
such as carpet or flooring, by use of an electric scooter indoors.
PROPER RIDING ATTIRE
Always wear proper protective equipment, such as an approved safety helmet
(with chin strap securely buckled), elbow pads and kneepads. A helmet may
be legally required by local law or regulation in your area. A long-sleeved
shirt, long pants, and gloves are recommended. Always wear athletic shoes
(lace-up shoes with rubber soles) and keep shoelaces tied and out of the way
of the wheels, motor and drive system. Never ride barefooted or in sandals.
USING THE CHARGER
The charger supplied with the electric scooter should be regularly examined
for damage to the cord, plug, enclosure and other parts. In the event of such
damage, the scooter must not be charged until the charger has been repaired
or replaced.
Use only with the recommended charger.
Use caution when charging.
The charger is not a toy. Charger should be operated by an adult.
Do not operate charger near flammable materials.
Unplug charger and disconnect from scooter when not in use.
Always disconnect from the charger prior to wiping down and cleaning your
scooter with damp cloth.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE
WARNINGS FURTHER INCREASES RISK OF SERIOUS INJURY. USE
AT YOUR OWN RISK AND WITH APPROPRIATE AND SERIOUS
ATTENTION TO SAFE OPERATION. USE CAUTION.
WARNING: Riding an electric scooter does present potential risks and
caution is required. Like any riding product, an electric scooter has inherent
hazards associated with its use (for example, falling off or riding it into a
hazardous situation). Like any riding product, electric scooters can and are
intended to move and it is therefore, of course, possible to lose control or
otherwise get into dangerous situations. Both children, and adults responsible
for supervising them, must recognize that if such things occur, a rider can
be seriously injured or die even when using safety equipment and other
precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.
WARNING: PARENTAL AND ADULT RESPONSIBILITY AND
SUPERVISION IS NECESSARY: Because products, like electric scooters,
can and do present potential hazards plainly associated with their use, it is
well recognized THE NEED FOR EXERCISE OF PARENTAL RESPONSIBILITY IN
SELECTING RIDING PRODUCTS APPROPRIATE TO THE AGE OF A CHILD, OR
PARENTAL SUPERVISION IN SITUATIONS IN WHICH CHILDREN OF VARIOUS
AGES MAY HAVE ACCESS TO THE SAME RIDING PRODUCTS, IS IMPORTANT.
Not every product is appropriate for every age or size of child, and different
age recommendations are found within this category of product which are
intended to reflect the nature of the hazards and the expected mental or
physical ability, or both, of a child to cope with the hazards.
The recommended minimum rider age is 8 and older. Any rider unable to
fit comfortably on the scooter should not attempt to ride it. A parent’s decision
to allow his or her child to ride this product should be based on the child’s
maturity, skill and ability to follow rules.
Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating the scooter.
Persons with any mental or physical conditions that may make them
susceptible to injury, impair their physical dexterity or mental capabilities
to recognize, understand, and follow safety instructions and to be able to
understand the hazards inherent in scooter use, should not use or be permitted
to use products inappropriate for their abilities. Persons with heart conditions,
head, back or neck ailments (or prior surgeries to these areas of the body), or
pregnant women, should be cautioned not to operate such products.
DO NOT EXCEED THE WEIGHT LIMIT OF 120 lb (54 kg). Rider weight
does not necessarily mean a person’s size is appropriate to fit or
maintain control of the scooter.
CHECK AND MAINTAIN SCOOTER CONDITIONS
Before use, check to confirm that covers and guards are in place and in
serviceable condition. Check that the brake is functioning properly, that the
front tire is inflated properly and has sufficient tread remaining and that the
rear wheel is free of flat spots from wear. The scooter should be maintained
and repaired in accordance with the manufacturer’s specifications, using only
the manufacturer’s authorized replacement parts, and should not be modified
from the manufacturer’s original design and configuration.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations which may
affect the locations where the electric scooter may be used. Keep
safely away from cars and motor vehicle traffic at all times. Only use
where allowed and with caution.
Do not activate the speed control on the hand grip unless you are on the scooter
and in a safe, outdoor environment suitable for riding. The electric scooter
must be moving at least 3 mph (5 km/h) before the motor will engage.
The normal powered top speed of this scooter will be approximately 11 mph
(18 km/h), which can be affected by conditions, such as rider weight, inclines
and battery charge level. Avoid excessive speeds that can be associated with
downhill rides.
Maintain a hold on the handlebars at all times. Do not touch the brakes or
motor on your scooter when in use or immediately after riding, as these parts
can become very hot.
1
BEFORE YOU BEGIN
Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect
the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping.
Because the scooter was 95 percent assembled and packed at the factory, there should not be any problems, even if the
box has a few scars or dents.
MAKE SURE POWER IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR
MAINTENANCE PROCEDURES.
Estimated Assembly and Set-Up Time
Razor recommends assembly by an adult.
Allow up to 10 minutes for assembly, not including initial charge time.
Allow up to 12 hours for charge (see page 4 for charging information).
WARNING:
DO NOT USE NON-RAZOR
PRODUCTS WITH YOUR RAZOR
ELECTRIC SCOOTER. The
scooter has been built to certain
Razor design specifications. The
original equipment supplied at
the time of sale was selected
on the basis of its compatibility
with the frame, fork and all
other parts. Certain aftermarket
products may not be compatible
and will void the warranty.
Charger
(Note: Charger design may
vary from one shown)
Note: Electric scooter must be
moving at least 3 mph (5 km/h)
while applying throttle to
engage motor.
Twist-Grip Throttle
3.
Brake Lever
Product ID Locations:
(See locations to the left)
1.
2.
3.
4.
1.
Collar Clamp
Handlebar Stem
Underneath Battery Tray
Charger
UPC Side of Box (Not Shown)
Limiter
Motor
On/Off Switch
Charger Port
- Battery
- Control Module
2.
Box Contents:
•
•
•
•
Electric Scooter
Charger
Allen Wrench
Owner’s Manual
Required Tool
5 mm Allen Wrench
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
2
ASSEMBLY AND SET-UP
Attaching the Handlebars
WARNING: Do not attempt
to thread the stem into the front
fork thread.
Tool Required: 5 mm Allen Wrench
Note: Make sure any cables/wires
are out of the way before inserting
the stem into the fork.
WARNING: Failure to
properly tighten the collar clamp
may allow the handlebars to
dislodge while riding and may cause
you to lose control and fall. When
correctly tightened, the handlebars
will not rotate out of alignment
with the front wheel under normal
circumstances.
2
1
With a twisting motion, push
and twist to slide the handlebars
onto the fork.
Loosen the bolts from the
collar clamp.
Note: The cable and wire assembly
from the handlebar must not
wrap around the steering tube or
handlebar. Sharp bends or twisting
of the brake cable can cause the
brakes to malfunction.
3
With the front wheel pointed straight ahead and the handlebars square to
the front wheel, tighten both bolts on the clamp with a 5 mm Allen wrench.
Tighten securely.
Inflating the Tire
The front tire is inflated when shipped, but it invariably may lose some pressure between the point of manufacturing
and your purchase. Always inflate tire to the correct PSI before first time use.
Lower air pressure can result in a shorter ride time.
Periodically check front tire. Reinflate when needed.
WARNING:
Do not use the electric scooter for
the first time until you have inflated
the tires to the correct PSI. Failure
to do so may damage your electric
scooter and void your warranty.
WARNING:
Do not over inflate, as this could
damage the tire or wheel.
Note: The pressure air supplies
found at gasoline stations are
designed to inflate high-volume
automobile tires. If you decide to
use such an air supply to inflate your
electric scooter tires, first make sure
the pressure gauge is working, then
use very short bursts to inflate to
the correct PSI. If you inadvertently
over-inflate the tire, release the
excess pressure immediately.
1
Using a bicycle-style tire pump
equipped for a Schrader-type valve,
inflate the front tire to the correct PSI
indicated on the sidewall of the tire.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
3
CHARGING THE BATTERY
Your electric scooter may not have a fully charged battery; therefore you must charge the battery prior to use.
• Initial charge time: 12 hours.
• Recharge time: up to 12 hours, even if the light
turns green. Recommended maximum charging time
is 24 hours.
• Always charge the battery immediately after riding.
• Fully charge battery before storing for extended
periods of time.
• Unplug charger from the wall outlet when not in use.
• Failure to recharge battery periodically may result in a
battery that will not accept a charge.
Charger
• Make sure the power is turned OFF when product
is not in use. If the ON/OFF switch is left on for an
extended period of time, the battery may reach a stage
at which it will no longer hold a charge.
• To ensure long battery life, never store the product in
freezing or below freezing temperatures! Freezing will
permanently damage the battery.
• Run time: Up to 60 minutes of continuous ride time.
Run time may vary depending on riding conditions,
rider weight, climate, and/or proper maintenance.
• Constant starting and stopping may shorten ride time.
• Battery life can vary depending on proper maintenance
and usage of the product.
WARNING: Use ONLY
with the recommended charger.
Batteries are only to be charged
under adult supervision. The charger
is not a toy. Always disconnect the
charger before wiping down and/or
cleaning the electric scooter with a
damp cloth.
The charger supplied with the
electric scooter should be regularly
examined for damage to the cord,
plug, enclosure and other parts.
In the event of such damage,
the electric scooter must not be
charged until it has been repaired
or replaced.
Chargers have built-in overcharge
protection to prevent battery from
being overcharged.
LED light
Note: If the charger gets warm
during regular use, this is a normal
response and is no cause for
concern. If your charger does not
get warm during use, it does not
mean that it is not working properly.
Note: Make sure power is turned
OFF when product is not in use. If
the ON/OFF switch is left on for an
extended period of time, the battery
may reach a stage at which it will
no longer hold a charge.
1
2
Plug the charger plug into wall
outlet. The light on the charger
should be green.
Note: If green light (LED) does not
turn on, try a different outlet.
Plug the charger into the charger
port. Make sure the power is in
the OFF position. The light on the
charger should turn red during
charging. The light will turn green
again when charging is complete.
Wall outlet - Green (stand by)
Wall outlet and unit - Red (charging)
Wall outlet and unit - Green (charged)
Note: Continue charging unit even
if light turns green prior to 12 hours.
WARNING: Battery charge
can deplete over time. Periodically
recharge battery when not in use.
PRE-RIDE CHECKLIST
q
Brake
q
Hardware/Loose Parts
q
q
q
Wheels
q
Safety Gear
q
q
Laws and Regulations
Check the brake for proper function. When you squeeze
the lever, the brake should provide positive braking action.
When you apply the brake with the throttle on/engaged, the
brake cut-off switch should cut power to the motor.
Periodically inspect the wheels for excessive wear.
Tire
Periodically inspect the tire for excess wear and replace as
needed. Regularly check the tire pressure and inflate as needed.
Frame, Fork and Handlebars
Check for cracks or broken connections. Although broken frames
are rare, it is possible for an aggressive rider to run into a curb
or object and wreck and bend or break a frame. Get in the habit
of inspecting your scooter on a regular basis.
4
Before every ride, check all parts, such as nuts, bolts, cables,
fasteners, etc., to ensure they are secure and assembled correctly.
There should not be any unusual rattles or sounds from loose parts
or broken components. If the product is damaged, do not ride.
Reference “Safety Warnings” on page 1 of this manual.
Always wear proper protective gear, such as an approved safety
helmet. Elbow pads and kneepads are recommended. Always wear
athletic shoes (lace-up shoes with rubber soles) and keep shoelaces
tied and out of the way of the wheels, motor and drive system.
NEVER RIDE BAREFOOTED OR IN SANDALS.
Always check and obey any local laws or regulations.
Insurance
Do not assume that your existing insurance policies necessarily
provide coverage for scooter use. Check with your insurance
company for information regarding insurance.
USAGE
q Starting the Scooter
Turn power “ON”; put kickstand up and place both hands on the handlebars.
Place one foot on deck plate and with the other foot, push (kick start) scooter while twisting throttle. Place other foot on
deck plate once motor has engaged.
q Stopping the Scooter
Note: Electric scooter must be
moving at least 3 mph (5 km/h)
while engaging throttle to
engage motor.
Note: As an additional safety
feature, the scooter is designed to
cut power to the motor when the
hand brake is applied.
To stop, release the throttle and apply the brake until the product comes to a complete stop.
Note: Motor will re-engage,
(without having to kick start),
if brake is released and throttle
is engaged before scooter has
slowed down to under 3 mph
(5 km/h).
REPAIR AND MAINTENANCE
Turn power “OFF” before beginning repair or maintenance:
• Read the instructions
• Remove charger plug
• Turn the power off
• Secure the product under repair
• Exercise caution around
exposed parts
• Contact Razor customer service
if unsure about any repair or
maintenance
Adjusting the Brakes
Tool Required: 10 mm Wrench
B
1 To adjust brake cable play, thread
the brake lever adjuster in or out 1/4
to 1/2 turn until the desired brake
adjustment is attained. Most adjustments are complete at this step. If
brake still needs further adjustment,
proceed to step 2.
2 If brake is too tight or has too
A
3 Inspect the brake pads (A) for
much slack, use a 10 mm wrench
to loosen the brake cable and
adjust accordingly.
proper alignment against the wheel
or excess wear. To realign brake
pads, loosen the fixing nut (B) and
adjust the pad to contact the rim.
Re-tighten and readjust as needed.
Verify proper brake function prior to
riding the scooter.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
5
REPAIR AND MAINTENANCE
q Front Tire Replacement
Note: Front wheel
hardware sequence
Tools Required: Two (2) 16 mm Wrenches
Right Side (Throttle)
8-4 Spacer
8-3 Washer
8-2 Spring Washer
8-1 M10 locknut
Middle
8-5 Front axle bolt
8-1
8-3
8-5
8-2
8-4
8-3
8-1
8-4 8-2
1
Using two (2) 16 mm wrenches, loosen the axle bolt.
Remove wheel and install replacement wheel.
(Note the sequence of the hardware)
Left Side (Brake)
8-4 Spacer
8-3 Washer
8-2 Spring Washer
8-1 M10 locknut
q Rear Wheel/Hub Motor/Battery Replacement
Tools Required: Phillips Screwdriver and Two (2) 13 mm Wrenches
(Battery Replacement Steps 1-3)
B.
A.
A.
Note: Rear wheel/motor
hardware sequence
1
Using a Phillips screwdriver remove the six (6)
screws and remove the deck plate.
(Note: There are two (2) sizes of screws,
A-Small, B-Large)
14-3
14-4
14-5
14-6
14-7
2
Using a Phillips screwdriver remove
the battery strap.
14-1
14-2
Left Side
14-1 Phillips Screws (3)
14-2 Motor Housing
Right Side
14-3 Spacer
14-4 Nut
3
Disconnect the battery wire connector from the
control module and carefully remove the battery.
Note: If only replacing battery, install new battery
and reverse steps 1-3.
4
Disconnect the motor wire connector from the
control module.
6
Frame
14-5 Flat Washer
14-6 Lock-Washer
14-7 Locknut
REPAIR AND MAINTENANCE
q Rear Wheel/Hub Motor/Battery Replacement Cont’d
Tools Required: Phillips Screwdriver and Two (2) 13 mm Wrenches
Note: When re-inserting the motor
wires into the connector, make sure
the red wire connects to the yellow
wire and the black wire connects to
the blue wire.
Red
Black
Note:
Motor
Red
Black
5
Using a pointed object carefully depress the
tabs on the metal pins inside of the motor wire
connector and remove the wires. Carefully pull
wires out from battery tray.
6
1
1
Control Module
Yellow
Blue
Using a Phillips screwdriver remove the three (3)
screws that attach the motor housing to the frame.
B.
A.
A.
7
Using a 13 mm wrench, loosen the outside
locknut (14-6). Use a 13 mm wrench to prevent the
inside nut (14-3) from turning.
Remove wheel/hub motor.
8
To install the replacement wheel/hub motor,
reverse steps 1 through 7.
q Battery Care and Disposal
Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum battery
life, carefully read the “Charging the Battery” section on page 4 of this owner’s manual.
Pb
CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED.
Pb
Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an
environmentally safe manner. Do not dispose of a lead-acid battery in a fire. The battery may explode or leak. Do not
dispose of a lead-acid battery in your regular household trash. The incineration, land filling or mixing of sealed leadacid batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state
approved lead-acid battery recycler or a local seller of automotive batteries. If you live in Florida or Minnesota, it is
prohibited by law to throw away lead-acid batteries in the municipal waste stream.
q Charger
The charger supplied with the electric scooter should be
regularly examined for damage to the cord, plug,
enclosure and other parts and in the event of such
damage, the product must not be charged until it has
been repaired or replaced.
Use ONLY with the recommended charger.
q Wheels
Wheels and drive system are subject to normal wear
and tear. It is the responsibility of the user to periodically
inspect wheels for excess wear and replace hub motor
components as required.
q Replacement Parts
The most frequently requested replacement parts are
available for purchase at some Razor retail partners. For
the complete selection of replacement parts visit
shop.razor.com.
q Repair Centers
For a list of authorized Razor repair centers:
• Check online at www.razor.com.
• Additional Customer Service contact information is
listed on the back of this manual.
7
WARNING: If a battery
leak develops, avoid contact with
the leaking acid and place the
damaged battery in a plastic bag.
Refer to the disposal instructions
at left. If acid comes into contact
with skin or eyes, flush with cool
water for at least 15 minutes and
contact a physician.
WARNING: Battery
posts, terminals and related
accessories contain lead and
lead compounds. Wash your
hands after handling.
TROUBLESHOOTING GUIDE
*Product(s) should be turned OFF and fully charged prior to doing any Troubleshooting.
NOTE: All troubleshooting steps should be performed by an adult only.
Problem
Possible Cause
Solution
Does not work out of the box
Product must be traveling at least
3 mph (5 km/h) before motor will engage
Kick start to at least 3 mph (5 km/h) while twisting throttle to
engage motor.
Loose connection(s)
Check for loose connections/wires underneath the deck plate.
Loose connection(s)
Check for loose connections/wires underneath the deck plate.
No lights on charger
Check power to wall outlet and/or try a different outlet.
Undercharged battery
Check lights on charger:
Plugged into wall - Green
Plugged into wall & product - Red (charging)
Plugged into wall & product - Green (charging complete)
No lights/Blinking lights - Replace Charger
Battery will not hold a charge
With no weight on the product, lift up back end; manually (and
carefully) spin rear wheel and twist throttle to engage the motor. If
motor engages - replace battery.
Riders weight
Do not exceed 120 lb (54 kg) maximum weight limit.
Riding conditions
Use only on flat, dry surfaces. Avoid inclines and areas with
heavy debris.
Battery not fully charged
Charge product for a full 12 hours.
Old/damaged battery
Replace battery.
No longer works
Short run time/runs slow
Charge battery at least once a month when not in use.
Do not store product in freezing or below freezing temperatures.
Freezing will permanently damage the battery and greatly reduce
ride time.
Refer to page 4 for charging information.
Runs intermittently
Loose connection(s)
Check the wires around the throttle and connectors underneath the
deck plate.
Replace - twist-grip throttle.
For more troubleshooting tips, a list of available replacement parts or to locate an authorized Service Center in your area,
visit our website at www.razor.com or call toll free +1 866-467-2967 to speak to a live Customer Service Representative.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
8
POWER CORE E100 ELECTRIC SCOOTER PARTS
Keep your electric scooter running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
1.
2.
3.
4.
5.
6.
7.
8.
Tube Plug
Handlebar Grips (Right/Left)
Single Speed Twist Grip Throttle
Handlebar Stem
Brake Lever Assembly
Battery 24V (2 12V)/6A
Collar Clamp
Headset (Upper/Lower)
1
2
3
9.
10.
11.
12.
13.
14.
15.
16.
4
Frame
Front Fork
Front Caliper Brake With Brake Pads
Front Wheel Complete
Kickstand
Rear Wheel With Motor Complete
Motor Cover
Deck Plate
5
17.
18.
19.
20.
21.
22.
2
1
Battery Strap
Battery Tray
On/Off Switch
Charge Port
Reset Button
Control Module
6
16
7
17
18
19
20
21
22
8
9
10
11
12
13
14
15
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
9
NOTICE: INSURANCE
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC
RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED,
YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this product not expressly approved by Razor USA LLC, could void the user’s authority to operate the equipment.
WARRANTY
Razor Limited Warranty
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
The manufacturer warranties this product to be free of manufacturing
defects for a period of 90 days from date of purchase. This Limited Warranty
does not cover normal wear and tear, tire, tube or cables, or any damage,
failure or loss caused by improper assembly, maintenance, storage or use of
the Razor Power Core E100.
Razor does not offer an extended warranty. If you have purchased an extended
warranty, it must be honored by the store at which it was purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation or transportation;
• modified in any way;
• rented.
__________________________________________
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed below:
AMERICAS
EUROPE, MIDDLE EAST, AFRICA
ASIA
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
Razor USA LLC (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
Razor USA LLC (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
+1 866 467 2967
Monday - Friday
8:00 AM - 5:00 PM Pacific Time
customersupport@razorusa.com
+44 (0) 120 267 2702
info@razoreu.com
+81 50 7579 6622
info@razor-asia.com
DISTRIBUTED IN THE UK AND IRELAND BY:
DISTRIBUTED IN AUSTRALIA BY:
IMPORTED IN JAPAN BY B+ASIA
Re:creation Limited
2 Meadows Business Park
Station Approach, Blackwater
Camberley, Surrey GU17 9AB
United Kingdom
Funtastic Limited
2/307 Ferntree Gully Road,
Mount Waverley Vic 3149,
Australia
Razor USA LLC
+44 (0) 118 973 6222 Tel
+44 (0) 118 973 6220 Fax
sales@recreationltd.co.uk
+1 800 244 543
info@funtastic.com.au
Kurokawa 3-1, Asaoku,
Kawasaki, Kanagawa
215-0035 JAPAN
+81 90 1766 9672
info@razor-asia.com
Printed in China for Razor USA LLC.
Copyright © 2003-2017 Razor USA, LLC. All rights reserved. Razor® and the Razor logo design are among the registered trademarks of Razor USA LLC in the United States and/or select foreign
countries. Power Core™ and the Power Core E100 logo design are trademarks of Razor USA LLC.
US_170825
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising