Razor | DXT Electric | Owner's Manual | Razor DXT Electric Owner's Manual

Razor DXT Electric Owner's Manual
DXT™ ELECTRIC DRIFT TRIKE
OWNER’S MANUAL
Read and understand this entire manual before allowing
child to use this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your product along with the 19 character product I.D. code with you
before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
CONTENTS
Usage ............................................................................................................... 8
Repair and Maintenance.............................................................................9-13
Troubleshooting Guide ................................................................................... 14
Product Parts .................................................................................................. 15
Warranty and Contact Information ................................................................ 18
Safety Warnings ...........................................................................................1-2
Before You Begin.............................................................................................. 3
Assembly and Set-Up....................................................................................4-7
Charging the Battery ........................................................................................ 7
Pre-Ride Checklist ............................................................................................ 8
SAFETY WARNINGS
WARNING: The DXT Electric Drift Trike is not the same as an “ordinary” tricycle and therefore may require greater skill to ride than an ordinary tricycle. It
is not for young children. The DXT Electric Drift Trike is designed to allow movement forward and extreme sideways drifting. Using this product requires open space,
free of other traffic or obstacles, and it is best ridden by a practiced rider aware of the product’s capabilities and willing to accept risks associated with drifts and
fast moving actions.
Riding any product can be a hazardous activity. Certain conditions may cause the equipment to fail without fault of the manufacturer. Like other products, the DXT
Electric Drift Trike can and is intended to move, and it is therefore possible to lose control, fall off and/or get into dangerous situations that no amount of care,
instruction or expertise can eliminate. If such things occur you can be seriously injured or die, even when using safety equipment and other precautions. RIDE AT
YOUR OWN RISK AND USE COMMON SENSE.
WARNING: NOT FOR CHILDREN UNDER AGE 16 OR HEAVIER
THAN 198 LB (90 KG). PARENTAL AND ADULT RESPONSIBILITY AND
SUPERVISION NECESSARY: Because products, like the DXT Electric Drift Trike,
can and do present potential hazards plainly associated with their use, it is
well recognized THE NEED FOR EXERCISE OF PARENTAL RESPONSIBILITY
IN SELECTING RIDING PRODUCTS APPROPRIATE TO THE AGE OF A CHILD,
OR PARENTAL SUPERVISION IN SITUATIONS IN WHICH CHILDREN OF
VARIOUS AGES MAY HAVE ACCESS TO THE SAME RIDING PRODUCTS, IS
IMPORTANT. Not every product is appropriate for every age or size of child,
and different age recommendations are found within this category of product
which are intended to reflect the nature of the hazards and the expected
mental or physical ability, or both, of a child to cope with the hazards. Razor
recommends that the DXT Electric Drift Trike be ridden only by riders
aged 16 and up. A parent’s decision to allow his or her child to ride
this product should be based on the child’s maturity, skill, and ability
to follow rules. Razor emphasizes that adults are strongly advised not
to disregard Razor’s recommendations or permit younger children to
ride the DXT Electric Drift Trike.
• Always wear safety equipment, such as helmet, wrist guards, gloves, knee
pads and elbow pads. Recognize that wrist guards may impair your ability
to properly grip the handlebars. Always wear a helmet when riding your the
DXT Electric Drift Trike and keep the chinstrap securely buckled.
• Always wear shoes.
• A parent’s decision to allow his or her child to ride this product should be
based on the child’s maturity, skill and ability to follow rules.
• This DXT Electric Drift Trike was manufactured for performance and
durability, but it is not impervious to damage. Trick riding can overstress or
damage any product, including this the DXT Electric Drift Trike, and the rider
assumes all risks associated with high stress activity.
• Ride on smooth, paved surfaces away from motor vehicles and other
hazards; riding on open public roads is dangerous.
• Avoid streets and surfaces with water, sand, gravel, dirt, leaves and other
debris.
• Loose or wet surfaces may further enhance risks when using this product
including braking.
• Install safety flag to increase visibility to others when riding.
• Never hitch a ride with a vehicle
• Do not ride at night or in reduced visibility conditions.
• Do not stand while riding.
• Sudden braking may result in being thrown forward.
• Use extra caution on steep or long hills as the rider can gain speed quickly.
Avoid excessive speeds as risks of loss of control, or of collisions or falls,
will be greater.
• Practice and develop drifting skills on large flat, smooth surfaces away from
motor vehicles and other hazards.
• Check and obey all local traffic laws and regulations.
• Watch out for pedestrians.
• Check and secure all fasteners before every ride.
• Do not exceed 198 lb (90 kg) total weight on the DXT Electric Drift Trike.
• Do not allow children under age 16 to use the DXT Electric Drift Trike.
• Rider weight does not necessarily mean rider’s size is appropriate to fit or
maintain control of the DXT Electric Drift Trike.
DO NOT EXCEED THE WEIGHT LIMIT OF 198 lb (90 kg). Rider weight alone
also does not necessarily mean a person’s size is appropriate to fit or maintain
control of the DXT Electric Drift Trike. Keep this product away from small
children and remember that only persons who are, at a minimum, completely
comfortable and competent while operating the product, intend this product
for use.
Persons with any mental or physical conditions that may make them
susceptible to injury, impair their physical dexterity or mental capabilities
to recognize, understand, and follow safety instructions, and to be able to
understand the hazards inherent in a product’s use, should not use or be
permitted to use products inappropriate for their abilities. Persons with heart
conditions, head, back or neck ailments (or prior surgeries to these areas of the
body), or pregnant women, should be cautioned not to operate this product.
NOTICE: This manual contains many warnings and cautions concerning the
consequences of failing to maintain, inspect or properly use your electric rideon product. Because any incident can result in serious injury or even death, we
do not repeat the warning of possible serious injury or death each time such a
possibility is mentioned.
CHECK AND MAINTAIN DXT ELECTRIC DRIFT TRIKE
Before use, check to confirm that any and all chain guards or other covers
and guards are in place and in serviceable condition. Check that the parts are
functioning properly, that the main driving tire is inflated properly and has
sufficient tread remaining. The DXT Electric Drift Trike should be maintained
and repaired in accordance with the manufacturer’s specifications, using only
the manufacturer’s authorized replacement parts, and should not be modified
from the manufacturer’s original design and configuration. Replace worn or
broken parts immediately.
1
SAFETY WARNINGS
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Adult supervision is recommended. Electric drift trike are meant to be used
only in controlled environments free of potential traffic hazards. Do not allow
rider to ride an electric drift trike in any areas where vehicle traffic is present.
Rider must maintain a hold of the handlebars at all times. Never allow more
than one rider at a time to ride an electric drift trike. Never use near steps,
sloped driveways, hills, roadways, alleys or swimming pool areas. Do not ride
an electric drift trike in wet weather. Electric drift trikes are intended for use on
solid, clean and dry surfaces such as pavement or level ground without loose
debris such as rocks or gravel. Wet, slick or uneven and rough surfaces may
impair braking traction, and contribute to possible accidents. Do not ride an
electric drift in mud, ice, puddles or water. Avoid excessive speeds that can be
associated with downhill rides. Never risk damaging surfaces such as carpet
or flooring by use of an electric drift trike indoors. Do not ride at night or when
visibility is impaired.
PROPER RIDING ATTIRE
Always ensure rider is wearing proper protective equipment, such as an
approved safety helmet. A helmet may be legally required by local law or
regulation in your area. Always wear shoes and keep shoelaces tied and out
of the way of the wheels. Never ride barefooted or in sandals. Long pants are
recommended and may reduce risk of abrasion if legs come in contact with
wheels when riding.
WARNING: ALWAYS INSPECT ELECTRIC DRIFT TRIKE PRIOR TO
RIDING. Properly inspecting and maintaining your electric drift trike can reduce
the risk of injury. Always inspect your drift trike before riding and regularly
maintain it.
Aggressive riding reduces your ability to maneuver and control. Take necessary
precautions and practice in a safe area.
WARNING: CHECK LOCAL LAWS REGARDING USE. Check local laws
and regulations to see where and how you may use your drift trike legally. In
many states and local areas riders are required BY LAW to wear a helmet.
Check local laws and regulations regarding laws governing helmet use and
electric drift trike operation in your area.
You will see people on TV and videos doing tricks or stunts. These are people
who have been practicing a long time and accept the risks of trick riding
activity. Do not assume that you can attempt to do the same tricks without
great risk.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS
FURTHER INCREASES RISK OF SERIOUS INJURY. USE AT YOUR OWN
RISK AND WITH APPROPRIATE AND SERIOUS ATTENTION TO SAFE
OPERATION. USE CAUTION.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
2
BEFORE YOU BEGIN
Remove contents from box and check parts against parts diagram found on page 15. Remove the separators that
protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint or
dents that may have occurred during shipping. Because the DXT Electric Drift Trike was partially assembled and
packed at the factory there should not be any problems, even if the box has a few scars or dents.
Estimated Assembly and Set-Up Time
Allow up to 15–20 minutes for assembly. Two (2) person assembly recommended.
Allow up to 12 hours for charge (see page 7 for charging information).
Flag
Charger
(Note: Charger design may
vary from one shown)
WARNING: Safety flag
is intended to increase rider’s
visibility to others. Do not bend
excessively (flag can break if over
stressed) nor remove from seat
when riding.
Twist Grip Throttle
3
WARNING: DO NOT
USE NON-RAZOR PRODUCTS
WITH YOUR DXT ELECTRIC DRIFT
TRIKE. The DXT Electric Drift
Trike has been built to certain
Razor design specifications. The
original equipment supplied at
the time of sale was selected
on the basis of its compatibility
with the frame, fork and all
other parts. Certain aftermarket
products may not be compatible
and will void your warranty.
Rear Wheels
Brake Lever
Battery Box
Product ID Locations:
Front Wheel
Assembly
See locations to the left
1.
2.
3.
4.
2
R
1
Frame (underneath unit)
Front Fork
Charger
Box - Side of UPC (not shown)
Seat
L
Required Tools
Box Contents:
•
•
•
•
•
Two (2) 5 mm Allen Wrenches
6 mm Allen Wrench
13 mm Wrench
DXT Electric Drift Trike
Flag
Charger
Tools
Owner’s Manual
Spoke Tensioner
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
3
ASSEMBLY AND SET-UP
Assembling the Frame
Required Tools: Two (2) 5 mm Allen Wrenches
B (Longer)
A (Shorter)
1 Using two (2) 5 mm
Allen wrenches, remove the
three (3) coupling bolts from the
downtube. Remove and discard
the plastic insert.
3
2 Connect the downtube to the
rear frame and align the holes on
the downtube with the holes on
the rear frame.
Re-insert the two (2) longer
coupling bolts (B) through
downtube and rear frame and
tighten securely in place.
4
Re-insert the one (1) shorter
coupling bolt (A) through the center
frame and downtube and tighten
securely in place.
Attaching the Front Fork
Required Tools: 5 mm Allen Wrench and 13 mm Wrench
WARNING: Failing to
properly tighten the steering bolt
that attaches the front fork assembly
to the frame assembly can cause you
to lose control and fall.
1
Using a 5 mm Allen wrench
and a 13 mm wrench, remove
the steering bolt and locknut
from the downtube.
Note: Place finger underneath
the downtube to prevent the
bottom bushing from falling
out and getting lost.
4 Align the downtube with the
hole in the upper and lower crown
and re-insert the steering bolt. Securely tighten using a 5 mm Allen
wrench and a 13 mm wrench.
2 Using a 13 mm wrench,
3
Re-insert the bottom bushing
into the downtube then carefully
slide the downtube between the
upper and lower crowns.
loosen the two (2) bolts on
the upper crown.
5 Re-tighten the two (2) 13 mm bolts
on the upper crown.
6
Use zip tie to keep cable wires
from rubbing against the front wheel
when unit is in motion.
4
ASSEMBLY AND SET-UP
Attaching the Handlebars
Required Tool: 6 mm Allen Wrench
R
L
Brake
Lever
Throttle
1
Place handlebars between the upper and lower
handlebar clamps.
Note: Make sure brake lever is on the left (from
sitting position).
2
Align the handlebars parallel to the front fork. Using
a 6 mm Allen wrench, tighten all four (4) bolts securely to
the upper crown.
Note: When properly tightened, the handlebars should
not move forward or backward.
Attaching the Seat
Required Tools: Two (2) 5 mm Allen Wrenches
1
Using two (2) 5 mm Allen wrenches, remove the four
(4) coupling bolts from the frame.
2
Place the seat at desired position. Align the four
(4) holes in the seat with the holes in the frame. Reinsert the coupling bolts and tighten bolts until seat is
securely in place.
Attaching the Foot Pegs
Required Tool: 5 mm Wrench
1
Using an 5 mm Allen wrench, loosen the two (2)
coupling bolts on the foot pegs.
2
Slide the foot pegs onto the front of the
downtube, as shown, and tighten bolts securely.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
5
ASSEMBLY AND SET-UP
Attaching Flag
1
Assemble flag as shown
2
Insert flag into fixed hole located on seat.
Inflating the Tires
The tires are inflated when shipped, but will invariably lose some pressure between the point of manufacturing and
your purchase. Inflate the tires to the correct PSI before first time use.
Periodically check the tires. Reinflate when needed.
WARNING:
Do not use the DXT Electric Drift
Trike for the first time until you have
inflated the tire to the correct PSI.
Failure to do so may damage your
DXT Electric Drift Trike and will void
your warranty.
WARNING:
Do not over inflate, as this could
damage the tires or wheels.
Note: The pressurized air supplies
found at gasoline stations are
designed to inflate high-volume
automobile tires. If you decide to
use such an air supply to inflate
your tire, first make sure the
pressure gauge is working, then
use very short bursts to inflate to
the correct PSI. If you inadvertently
over-inflate the tire, release the
excess pressure immediately.
1
Using a bicycle tire pump equipped for a Schrader valve, inflate the
tires to the PSI indicated on the sidewall of the tire.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
6
ASSEMBLY AND SET-UP
Checking Spoke Tension
WARNING: Regularly check
the spoke tension and retighten
the spokes whenever loose. If you
have any doubt, ask an experienced
motorcycle or bicycle mechanic to
inspect your spokes to determine
if the spokes need tightening or
adjusting.
Spoke Flange
Spoke
Hub Flange
Spke Flange
Note: Tightening each nipple more
than a 1/2 turn each can cause the
wheel to become distorted and
wobbly, thus permanently damaging
the wheel.
Rim
Nipple
Nipple
1 Verify spoke tension by grasping and shaking each spoke. Spoke
2 Start with spoke closest to tire
should not be loose from hub. Look for any play between spoke flanges
where it mates with hub. Try to turn nipple using your fingers. You
should not be able to spin any nipple by hand. If one or more spokes
are loose, or if you can turn any nipple using your fingers, all spokes
must be checked and need to be tightened with a spoke tightener.
valve and tighten each nipple. In
sequence, exactly 1/4 to 1/2 turn.
A single 1/4 to 1/2 turn may not
be enough to bring the spokes into
proper tension. Continue tightening
all spokes in sequence, no more than
1/2 turn until all spokes are tight.
CHARGING THE BATTERY
Your DXT Electric Drift Trike may not have a fully charged battery; therefore you must charge the battery prior to use.
• Initial charge time: 12 hours.
• Recharge time: up to 12 hours, even if the light turns green.
Recommended maximum charging time is 24 hours.
• Always charge the battery immediately after riding.
• Fully charge battery before storing for extended
periods of time.
• Unplug charger from the wall outlet when not in use.
• Failure to recharge battery periodically may result in a
battery that will not accept a charge.
• Make sure the power switch is turned OFF when unit is
not in use. If the power switch is left on for an extended
period of time, the battery may reach a stage at which it
will no longer hold a charge.
• To ensure long battery life, never store the product in
freezing or below freezing temperatures! Freezing will
permanently damage the battery.
• Run time: Up to 60 minutes of continuous ride time.
Run time may vary depending on riding conditions, rider
weight, climate, and/or proper maintenance.
• Constant stopping and starting may shorten ride time.
• Battery life can vary depending on proper maintenance
and usage of the unit.
WARNING: Use ONLY
with the recommended charger.
Batteries are only to be charged
under adult supervision. The charger
is not a toy. Always disconnect the
charger before wiping down and/or
cleaning the DXT Electric Drift Trike
with a damp cloth.
The charger supplied with the DXT
Electric Drift Trike should be regularly
examined for damage to the cord,
plug, enclosure and other parts.
In the event of such damage, the
DXT Electric Drift Trike must not be
charged until it has been repaired
or replaced.
Chargers have built-in overcharge
protection to prevent battery from
being overcharged.
Charger
Note: If the charger gets warm
during regular use, this is a normal
response and is no cause for concern.
If your charger does not get warm
during use, it does not mean that it is
not working properly.
Note: Make sure power is turned
OFF when unit is not in use. If
the power switch is left on for
an extended period of time, the
battery may reach a stage at which
it will no longer hold a charge.
1
2
Plug the charger plug into wall
outlet. The light on the charger
should be green.
Note: If green light (LED) does not
turn on, try a different outlet.
Plug the charger into the
charger port on the product. Make
sure the power switch is in the
OFF position. The light on the
charger should turn red during
charging. The light will turn green
again when charging is complete.
7
Wall outlet - Green (stand by)
Wall outlet and Unit - Red (Charging)
Charging complete - Green (Charged)
Note: Continue charging unit even if
light turns green prior to 12 hours.
WARNING: Failure to
recharge the battery at least once a
month may result in a battery that
will no longer accept a charge.
PRE-RIDE CHECKLIST
Brake
Safety Gear
Check the brake for proper function. When you squeeze the
lever, the brake should provide positive braking action.
Always wear proper protective gear, such as an approved safety
helmet. Elbow pads and kneepads are recommended. Always wear
closed toe shoes (lace-up with rubber soles) and keep shoelaces
tied and out of the way of the wheels. NEVER RIDE BAREFOOTED
OR IN SANDALS.
Tire/Wheels
Periodically inspect the tire/wheels for excess wear and replace
as needed. Regularly check the tire pressure and inflate as
needed. If you get a flat tire, the inner tube can be patched or
a new tube can be purchased from Razor or an authorized
repair center.
Laws and Regulations
Always check and obey any local laws or regulations.
Insurance
Frame, Fork and Handlebars
Do not assume that your existing insurance policies necessarily
provide coverage for product use. Check with your insurance
company for information regarding insurance.
Check for cracks or broken connections. Although broken frames
are rare, it is possible for an aggressive rider to run into a curb
or object and wreck, bend or break the frame. Get in the habit of
inspecting your product on a regular basis.
Be Careful!
Use extra caution on steep or long hills. Avoid excessive speeds.
Never ride in traffic or on the street and watch your surroundings
for pedestrians, bikers, boarders and skaters.
Hardware/Loose Parts
Check and secure all fasteners before every ride. There should
not be any unusual rattles or sounds from loose parts or broken
components. If the unit is damaged, do not ride. Reference
“Safety Warnings” on page 1 of this manual.
Maintain a hold on the handlebars at all times.
USAGE
Riding the DXT Electric
Drift Trike
Stopping the DXT Electric
Drift Trike
• Place both hands on the handlebars and both feet
on the foot pegs.
• Accelerate the DXT Electric Drift Trike to desired
riding speed
• Coast when drifting
• Straighten front wheel before accelerating when a
drift is completed
• To stop the unit, apply the brake lever until the unit
comes to a complete stop.
Note: Keep both feet on the foot
pegs when unit is in motion.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
8
REPAIR AND MAINTENANCE
Turn power switch “OFF” before beginning repair or maintenance:
• Read the instructions
• Remove charger plug
• Turn the power switch off
• Secure the unit under repair
• Exercise caution around
exposed parts
• Contact Razor customer service
if unsure about any repair or
maintenance
Adjusting the Brake
Tools Required: 5 mm Allen wrench
WARNING: The brake is
capable of causing the DXT Electric
Dift Trike to skid the tire throwing
an unsuspecting rider. Practice in
an open area free from obstacles
until you are familiar with the brake
function. Avoid skidding to a stop as
this can cause you to lose control or
damage the rear tires.
Testing the Brake. To use the
brake, squeeze the lever to increase
the pressure on the brake. The
brake lever is fitted with a cable
adjuster to compensate for cable
stretch and/or to fine-tune the lever
movement to brake engagement.
If brake is not engaging properly,
follow instructions for adjusting
the brake.
1 To adjust brake cable play,
thread the brake lever adjuster
in or out 1/4 to 1/2 turn until
the desired brake adjustment is
attained. Most adjustments are
complete at this step. If brake still
needs further adjustment, proceed
to step 2.
2 If the brake has too much
3 If the brake disc is rubbing on
slack, loosen the rear anchor bolt
with a 5 mm Allen wrench and
pull the brake cable tighter. The
distance between the end of the
brake cable and the anchor bolt
should be between 37 mm and
44 mm.
the brake pads, use your fingers to
twist the caliper adjuster in either
direction until disc is centered
between the brake pads.
Replacing the Fuse
Turn power switch OFF.
WARNING:
To prevent shock, please follow the
instructions accordingly and do not
skip or combine any steps.
1 Open battery compartment
located behind the seat.
2 Locate fuse box on top of
3 Remove damaged or burnt out
battery. Open the fuse cover to
expose the fuse.
fuse and replace with a new one
of equal amperage. Close the
fuse box.
4 Close battery compartment.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
9
REPAIR AND MAINTENANCE
Rear Wheel Replacement
Required Tool: 16 mm Socket wrench
1 Loosen the 16 mm locknut and remove rear wheel(s).
15-3
15-2
15-1
Rear Wheel Hardware Sequence
15-1. Locknut
15-2. Spring Washer
15-3. Flat Washer
2 Install replacement wheel(s) and tighten securely in place.
Note: the sequence of the hardware.
Rear Wheel Sleeve Replacement
Groove
1
Deflate tire and remove sleeve.
2
Slide replacement sleeve on to rear wheel. Align the
groove on the wheel with the inner lining of the sleeve.
Re-inflate tire to correct PSI (indicated on sidewall)
10
REPAIR AND MAINTENANCE
Front Wheel and Chain Replacement
Required Tools: 15 mm Wrench, 19 mm Wrench, Phillips screwdriver
1 Using a Phillips screwdriver, loosen the seven (7)
2 Loosen the tension from the chain tensioner.
3 Remove the chain from around the sprocket on the front
4 With a 15 mm and 19 mm open wrench remove the
screws on the chain guard.
wheel.
axle bolt. Remove front wheel.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
11
REPAIR AND MAINTENANCE
Front Wheel and Chain Replacement (Continued)
Required Tools: 5 mm Allen Wrench, 15 mm Wrench, 19 mm Wrench
9-3
9-2
9-1
9-5
9-4
5 Re-install axle bolt and tighten front wheel securely
to front fork.
6 Re-attach chain around the front wheel and the
motor sprocket.
Note: Make sure the chain tensioner is resting on the
outer side of the chain.
7 Re-attach chain guard.
12
Front Wheel Hardware Sequence
9-3. 19 mm Lock Nut
9-2. Flat Washer
Fork
9-1. Large Spacer
Front Wheel
9-5. Small Spacer
Fork
9-4. 15 mm Axle Bolt
REPAIR AND MAINTENANCE
Battery Care and Disposal
Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum battery
life, carefully read the “Charging the Battery” section on page 7 of this owner’s manual.
CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED.
Pb
Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an
environmentally safe manner. Do not dispose of a lead-acid battery in a fire; the battery may explode or leak. Do not
dispose of a lead-acid battery in your regular household trash. The incineration, land filling or mixing of sealed lead-acid
batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state
approved lead-acid battery recycler or a local seller of automotive batteries. If you live in Florida or Minnesota, it is
prohibited by law to throw away lead-acid batteries in the municipal waste stream.
Charger
WARNING: If a battery leak
develops, avoid contact with the
leaking acid and place the damaged
battery in a plastic bag. Refer to the
disposal instructions at left. If acid
comes into contact with skin or eyes,
flush with cool water for at least 15
minutes and contact a physician.
WARNING: Battery posts,
terminals and related accessories
contain lead and lead compounds.
Wash your hands after handling.
The charger supplied with the DXT Electric Drift Trike should be regularly examined for damage to the cord, plug,
enclosure and other parts, and in the event of such damage, the product must not be charged until it has been
repaired or replaced.
Use ONLY with the recommended charger.
Cleaning
Wipe with a damp cloth to remove dirt and dust. Do not use industrial cleaners or solvents, as they may damage the
surfaces. Do not use alcohol, alcohol-based or ammonia-based cleaners, as they may damage or dissolve the plastic
components or soften the decals or decal adhesive.
Wheels and Bearings
Under normal circumstances and conditions, Razor wheels and wheel bearings are maintenance free. Nonetheless,
it is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for
proper tightness, bearings for side-to-side play, and for loose parts. When a wheel develops play, this is an indication
of excess wear and replacement is necessary. Replace immediately with only genuine Razor wheels. Worn, tires,
wheels/bearings are considered normal wear-and-tear and are not covered by the Razor Warranty. Wheels other
than genuine Razor wheels may not be compatible with your DXT Electric Drift Trike. The use of anything other than
genuine Razor replacement parts may affect your safety and will void your warranty.
Replacement Parts
The most frequently requested replacement parts are available for purchase at some Razor retail partners.
For the complete selection of replacement parts visit shop.razor.com.
Service Centers
For a list of authorized Razor service centers:
• Check online at www.razor.com.
• Additional Customer Service contact information is listed at the back of this manual.
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
13
DXT ELECTRIC TROUBLESHOOTING
*Unit should be turned OFF and fully charged prior to doing any Troubleshooting
NOTE: All troubleshooting steps should be performed by an adult only
Problem
Possible Cause
Solution
Electric motorbike does not run
Undercharged battery
Charge the battery. A new battery should have been charged for at least 12 hours
before using the electric motorbike for the first time and up to 12 hours after each
subsequent use.
Check all connectors. Make sure the charger connector is tightly plugged into the
charging port, and that the charger is plugged into the wall.
Make sure power flow to the wall outlet is on.
Loose wires or connectors
Check all wires and connectors to make sure they are tight.
The fuse will burn out and automatically shut off the power if the motor is overloaded.
Electric motorbike was running
but suddenly stopped
Burned-out fuse
An excessive overload, such as too heavy a rider or too steep a hill, could cause the
motor to overheat. Replace the fuse with a new one of equal amperage. Correct the
conditions that caused the fuse to burn out and avoid repeatedly burning out fuse
(Refer to page 9 of this manual).
Contact your local Razor authorized service center for diagnosis and repair.
Short run time (less than
15 minutes per charge)
Motor or electrical switch damage
Charge the battery. A new battery should have been charged for at least 12 hours
before using the electric motorbike for the first time and up to 12 hours after each
subsequent use.
Undercharged battery
Check all wires and connectors. Make sure the battery connector is tightly plugged
into the charger connector, and that the charger is plugged into the wall.
Tires are not properly inflated
The tires are inflated when shipped but they invariably will lose some pressure
between the point of manufacturing and your purchase. Refer to instructions on
page 6 of this manual to properly inflate tires.
Battery is old and will not accept
full charge
Even with proper care, a rechargeable battery does not last forever. Battery life can
vary depending on proper maintenance and usage of unit. Replace only with a Razor
replacement battery.
Brakes are not adjusted properly
Refer to brake adjustment instructions on page 9 of this manual.
Riding conditions are too stressful
Use only on solid, flat, clean and dry surfaces, such as pavement or level ground.
Tires are not properly inflated
The tires are inflated when shipped, but they invariably will lose some pressure
between the point of manufacturing and your purchase. Refer to instructions on
page 6 of this manual to properly inflate tires.
Electric motorbike is overloaded
Make sure you do not overload the electric motorbike by allowing more than one
rider at one time, exceeding the maximum weight limit, going up too steep a hill or
towing objects behind the product.
Sometimes the product doesn’t
run, but other times it does.
Loose wires or connectors
Check all wires around the motor and all connectors to make sure they are tight.
Motor or electrical switch damage
Contact your local Razor authorized service center for diagnosis and repair.
Electric motorbike does not stop
when applying the brake
Brakes are not adjusted properly
Refer to instructions on page 9 of this manual to properly adjust brakes.
Electric motorbike makes loud
noises or grinding sounds
Chain is too dry.
Apply a lubricant such as 3 in 1™ or Tri-Flow™ to the chain.
Electric motorbike runs
sluggishly
For more troubleshooting tips, a list of available replacement parts or to locate an authorized Service Center in your area,
visit our website at www.razor.com or call toll free +1 866 467 2967 to speak to a live Customer Service Representative
14
DXT ELECTRIC PARTS
Keep your product running for years with genuine Razor parts. Visit our website to purchase replacement parts.
(Specifications subject to change without notice.)
1.
2.
3.
4.
5.
6.
7.
8.
9.
Handlebar Grips (x2)
Twist Grip Throttle
Handlebars
Brake Lever
Handlebar Clamps (Upper/Lower)
Front Fork
Chain Guard (Right/Left)
Chain
Front Wheel
9-1. Large Spacer
9-2. Flat Washer
9-3. Locknut
9-4. Axle Bolt
9-5. Small spacer
10. Down Tube
10-1. Steering bolt
10-2. Brushing (x2)
10-3. Bearing (x2)
10-4. Locknut
11. Chain Tensioner
12. Caliper Brake
13. Footpegs
13-1. Footpeg clamp
13-3. Coupling bolts (x2)
14. Rear Frame
14-1. Rear Frame Coupling Bolt (Long) (x2)
14-2. Rear Frame Coupling Bolt (Short) (x1)
3
2
15. Rear Wheel (x2)
15-1. Locknut (x2)
15-2. Spring Washer (x2)
15-3. Flat Washer (x2)
16. Sleeve (x2)
17. Control Module
18. Battery (3- 12v/12ah) with 30 amp fuse
18-1. Battery Bracket
18-2. Battery Bracket Bolt (x2)
19. Battery Cover
20. Charge Port
21. On/Off Switch
22. Seat
22-1. Seat Coupling Bolt (x4)
23. Flag
1
4
5
1
10-1
10-3
6
23
10-2
10-3
7
10-2
13-2
8
11
22-1
10
22
10-4
13-1
13
18-2
12
18-1
9
9-4
14-2
9-5
14
14-1
9-1
17
9-3
15
9-2
18
20
19
15-3
15-1
16
15-2
15
21
NOTICE: INSURANCE
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON
PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD
CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by Razor USA, could void the user’s authority to operate the equipment.
WARRANTY
Razor Limited Warranty
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
The manufacturer warranties this product to be free of manufacturing defects
for a period of 90 days from date of purchase. This Limited Warranty does not
cover normal wear and tear, tires, tubes or cables, or any damage, failure or loss
caused by improper assembly, maintenance, storage or use.
Razor does not offer an extended warranty. If you have purchased an extended
warranty, it must be honored by the store at which it was purchased.
For your records, save your original sales receipt with this manual and write
the serial number below.
This Limited Warranty will be void if the product is ever:
• used in a manner other than for recreation or transportation;
• modified in any way;
• rented.
__________________________________________
CUSTOMER SERVICE CONTACT INFORMATION
Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed below:
AMERICAS
EUROPE
ASIA
Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
Razor USA LLC (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
Razor USA LLC (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
+1 866 467 2967
Monday - Friday
8:00 AM - 5:00 PM Pacific Time
customersupport@razorusa.com
+44 (0) 1202 672702
+81 50 7579 6622
info@razor-asia.com
DISTRIBUTED IN THE UK BY:
DISTRIBUTED IN AUSTRALIA BY:
Re:creation Limited
2 Meadows Business Park
Station Approach, Blackwater
Camberley, Surrey GU17 9AB
United Kingdom
Funtastic Limited
Level 2, Tower 2, Chadstone Place
1341 Dandenong Road
Chadstone VIC 3148
Australia
+44 (0) 118 973 6222 Tel
+44 (0) 118 973 6220 Fax
sales@recreationltd.co.uk
+1 800 244 543
info@funtastic.com.au
Printed in China for Razor USA LLC.
Copyright © 2003-2016 Razor USA, LLC. All rights reserved. DXT™, Razor® and the Razor logo
design are among the registered trademarks of Razor USA LLC in the United States and/or
select foreign countries. DXT is a trademark of Razor USA LLC.
18
US_160728
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising