ADTRAN | Total Access 1500 System TL1 | Guide | Adtran Total Access 1500 System TL1 Guide

Adtran Total Access 1500 System TL1 Guide
Total Access® 1500 System
TL1 Reference Guide
61180008L1-35A
May 2003
Trademarks
Any brand names and product names included in this manual are trademarks, registered
trademarks, or trade names of their respective holders.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves
the right to change the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages
or for commercial losses even if ADTRAN has been advised thereof as a result of issue of
this publication.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
(256) 963-8000
©2003 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
ii
61180008L1-35A
About This Manual
This manual provides descriptions of Transaction Language 1 (TL1) commands for the
Total Access 1500 system. The purpose of this manual is to provide the technician with
general and specific information related to using TL1 commands with the Total Access
1500 system. The following is an overview of the contents:
Section 1
Introduction
Provides an overview of TL1 software and the network equipment that uses TL1
software.
Section 2
TL1 Commands
Provides information about how to use a TL1 command, which includes the syntax and
the general format of a TL1 command. This section also provides a list of commands that
apply to the Total Access 1500 system and provides information about the response
messages for TL1 commands.
Section 3
ADTRAN AID Formats
Provides information about ADTRAN-specific Access Identifier (AID) formats that are
used within the structure of a TL1 command.
Section 4
Common (SCU) TL1 Commands
Provides information about TL1 commands that are used for logging on and logging off
the Total Access 1500 system and TL1 commands that apply to the System Controller
Unit (SCU).
Section 5
Security TL1 Commands
Provides information about TL1 commands that are used to add, delete, and edit security
accounts for users that access the Total Access 1500 system.
Section 6
Surveillance TL1 Commands
Provides information about TL1 commands that are used to obtain data from an Network
Element (NE). A Total Access 1500 shelf is an NE. A module within the shelf is part of an
NE.
Section 7
System Maintenance TL1 Commands
Provides information about TL1 commands that are used to perform maintenance tasks for
the Total Access 1500 system.
Appendix A Input Commands Data Dictionary
Provides information about the parameter data used with TL1 Input commands.
Appendix B Response Messages Data Dictionary
Provides information about parameters received in a Response message sent to the
Operations System (OS) from an NE.
Appendix C Error Codes
Provides information about the error codes that may be received in a Response message.
61180008L1-35A
iii
Appendix D Alarms and Alarm Condition Codes
Provides information about the alarms and the alarm conditions codes generated by the
NEs.
Appendix E Autonomous Messages
Provides information about the Autonomous messages generated at an NE and sent to the
OS/user.
Appendix F Quad-Port Line Cards
Provides information about the Quad-Port line cards.
Appendix G Dual-Port Line Cards
Provides information about the Dual-Port line cards.
Appendix H Single-Port Line Cards
Provides information about the Single-Port line cards.
Appendix I List of Abbreviations
Provides a list of abbreviations used in this manual.
Appendix J Total Access 1500 TL1 Quick Reference Table
Provides quick reference information about TL1 Input commands and the Response
messages for the Total Access 1500 system.
iv
61180008L1-35A
Revision History
This is the first release of this document. Future revisions to this manual will be explained
in this subsection.
Certification
Total Access 1500 is compliant with all NEBS Level 3 requirements and is listed to
UL1950 3rd edition.
Federal Communications Commission Statement
This equipment generates, uses, and can radiate radio frequency energy. If not installed
and used in accordance with the instruction manual, this equipment may cause
interference to radio communications. Total Access 1500 has been tested and found to
comply with limits for a Class A digital device pursuant to Subpart B of Part 15 of FCC
Rules, which are designed to provide reasonable protection against such interference when
operated in a commercial environment.
This equipment does not exceed Class A limits for radio emission for digital apparatus, set
out in the Radio Interference Regulation of the Canadian Department of Communications.
Conventions
NOTE
Notes provide additional useful information.
CAUTION
Cautions signify information that could prevent service interruption.
WARNING
Warnings provide information that could prevent damage to the
equipment or endangerment to human life.
61180008L1-35A
v
vi
61180008L1-35A
Total Access® 1500 System TL1 Reference Guide
Table of Contents
Section 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1. Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2. TL1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transport Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL1 Sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL1 Message Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-1
1-1
3. Operations Support System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
4. Network Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
5. References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Section 2
TL1 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2. Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
3. Notations and Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
4. General Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Target Identifier (TID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Common Language Location Identifier (CLLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
5. Acknowledgment Responses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Acknowledgment Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
6. Normal Response Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Response Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
7. Total Access 1500 System TL1 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
MTA TL1 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Section 3
ADTRAN AID Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
1. INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
2. ADTRAN AID Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digroup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61180008L1-35A
3-1
3-1
3-1
3-1
vii
Table of Contents
Total Access 1500 System TL1 Reference Guide
Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entity Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Card Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL1 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
3-2
3-2
3-3
3-3
3-3
3-3
Section 4
Common (SCU) TL1 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
2. ACT-USER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-1
4-1
4-2
4-2
4-2
4-2
3. CANC-USER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3
4-3
4-3
4-3
4-3
4-3
4-4
4. RTRV-SYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5
4-5
4-5
4-5
4-5
4-5
4-6
5. RTRV-VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7
4-7
4-7
4-7
4-7
4-7
4-8
Section 5
Security TL1 Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
2. CANC-USER-SECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
viii
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Table of Contents
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1
5-1
5-2
5-2
Section 6
Surveillance TL1 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
2. ALW-MSG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1
6-1
6-1
6-2
6-2
6-2
6-2
3. INH-MSG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3
6-3
6-3
6-3
6-3
6-3
6-4
4. RTRV-ALM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-5
6-5
6-5
6-5
6-5
6-6
6-6
5. RTRV-COND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-7
6-7
6-7
6-7
6-7
6-8
6-8
6. RTRV-HDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
7. RTRV-PM-T1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61180008L1-35A
6-11
6-11
6-11
6-11
ix
Table of Contents
Total Access 1500 System TL1 Reference Guide
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
8. SCHED-PMREPT-T1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-13
6-13
6-13
6-13
6-13
6-14
6-14
Section 7
System Maintenance TL1 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
2. CHG-SPLIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1
7-1
7-1
7-2
7-2
7-2
7-2
3. CHG-SPLIT-LILO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3
7-3
7-3
7-3
7-3
7-3
7-4
4. CONN-LPACC-MET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5
7-5
7-5
7-5
7-5
7-6
7-6
5. CONN-MON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-7
7-7
7-7
7-7
7-7
7-7
7-8
6. CONN-TACC-MET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-9
7-9
7-9
7-9
7-9
x
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Table of Contents
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
7. DISC-TACC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-11
7-11
7-11
7-11
7-11
7-12
7-12
8. OPR-LPBK-TST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-13
7-13
7-13
7-13
7-13
7-13
7-14
9. REPT-STAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-15
7-15
7-15
7-15
7-15
7-15
7-16
10. RLS-LPBK-TST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-17
7-17
7-17
7-17
7-17
7-17
7-18
11. RST-TAP-MET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-19
7-19
7-19
7-19
7-19
7-19
7-20
Appendix A
Input Commands Data Dictionary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Appendix B
Response Messages Data Dictionary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
61180008L1-35A
xi
Table of Contents
Total Access 1500 System TL1 Reference Guide
Appendix C
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Appendix D
Alarms and Alarm Condition Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
SCU Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
LIU Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-5
Appendix E
Autonomous Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
2. Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
3. Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3
Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3
4. Performance Monitoring Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3
5. Condition Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3
6. Autonomous Message Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3
Appendix F
Quad-Port Line Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
2. AID Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
Port Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
3. Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1
Appendix G
Dual-Port Line Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-1
2. AID Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-1
3. Port Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-1
4. Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-1
Appendix H
Single-Port Line Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1
2. AID Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1
xii
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Table of Contents
3. Port Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1
4. Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1
Appendix I
List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-1
Appendix J
Total Access 1500 TL1 Quick Reference Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-1
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-1
2. Notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-1
3. AID Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-1
4. AID Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-1
5. Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-1
Figures
Figure 3-1.
Card Slot Numbers Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Tables
Table 2-1.
Table 2-2.
Table 2-3.
Table 3-1.
Table 3-2.
Table A-1.
Table B-1.
Table C-1.
Table D-1.
Table D-2.
Table E-1.
Table J-1.
61180008L1-35A
TL1 Input Command General Format Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL1 Response Message Format Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total Access 1500 TL1 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total Access 1500 AID Parameter Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total Access 1500 Line Cards Reference Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total Access 1500 TL1 Input Commands Data Dictionary . . . . . . . . . . . . . . . . . . . . . .
Total Access 1500 TL1 Response Messages Data Dictionary . . . . . . . . . . . . . . . . . . .
Total Access 1500 System Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total Access 1500 SCU Alarm Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total Access 1500 LIU Alarm Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Autonomous Messages Parameter Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total Access 1500 TL1 Quick Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
2-3
2-4
3-2
3-3
A-1
B-1
C-1
D-1
D-5
E-1
J-2
xiii
Table of Contents
xiv
Total Access 1500 System TL1 Reference Guide
61180008L1-35A
Section 1
Introduction
1.
PURPOSE
This manual provides Transaction Language 1 (TL1) reference information for the Total Access 1500
system. This document is intended for use by operating company personnel who use TL1 commands to
perform network management tasks for the Total Access 1500 system and its associated network
equipment.
This manual is for Total Access 1500 systems using the following System Controller Units (SCU): P/N
1180008L1#S, P/N 1180008L2#S, and P/N 1180008L3#S. The P/N 1180008L2#S and P/N 1180008L3#S
SCUs support Metallic Test Access (MTA).
For additional information about the Total Access 1500 system, refer to the Total Access 1500 System
Manual, 61180001L1#S-1.
2.
TL1 OVERVIEW
TL1 software provides an ASCII-based protocol that allows the exchange of messages between an
Operations Support System (OSS) and the Total Access 1500 system. An OSS is also referred to as an
Operations System (OS).
Transport Methods
The TL1 software uses the following methods for transporting messages:
•
•
X.25 using the Network Management port
Transmission Control Protocol (TCP)/Internet Protocol (IP) [TCP/IP] telnet socket using the 10BaseT
port
TL1 Sessions
The maximum number of TL1 logon sessions at one time depends on the physical and logical interfaces to
the Total Access 1500 system (SCU).
Maximum number of sessions to be provided.
TL1 Message Types
The TL1 software provides four types of operation messages:
1. Input command
– An input command is a message from an OS or other source to a Network Element. The message
instructs or requests the NE to perform a management-related function.
61180008L1-35A
1-1
Section 1, Introduction
Total Access 1500 System TL1 Reference Guide
2. Acknowledgment
– An acknowledgment is a reply from the NE that indicates an input command is being acted upon.
An NE sends an acknowledgment response if a normal response or error response cannot be sent
within two seconds. The Total Access 1500 system supports the following acknowledgment
responses:
•
IP – indicates In Progress. This acknowledgment response indicates the request has been
initiated and produces subsequent output messages, which give a termination report or a
termination report and command results.
OK – indicates All Correct (Good). This acknowledgment response indicates the command was
received and the requested action was initiated and completed. This acknowledgment response
is used in response to the REPT-STAT command or if the user cancels a partial input with a
Control-X key.
3. Output response (Response message or Error message)
– An output response is a detailed reply or set of replies to an input command. It contains information
that indicates whether the command was successfully executed. The output response also contains
any data that needs to be returned to the OS/user.
4. Autonomous
– An autonomous message is generated by an NE either on a periodic basis or is generated by an NE
to report an alarm or an event that occurs at the NE. These messages are normally triggered by alarm
conditions and are not in response to any input command.
•
3.
OPERATIONS SUPPORT SYSTEM
An OSS consists of application software that runs on a host computer and allows the host computer to
provide network management functions. The SCU provides the network management interface for the
Total Access 1500 system and the network equipment that interconnects to and interworks with the Total
Access 1500 system.
From a network management standpoint, the Total Access 1500 system and the network equipment are
referred to as Network Elements that exchange messages with the OS's host computer.
4.
NETWORK ELEMENTS
The Total Access 1500 shelf is an NE. The modules within the shelf are part of an NE.
5.
REFERENCES
Total Access 1500 System Manual, P/N 61180001L1-1
1-2
61180008L1-35A
Section 2
TL1 Commands
1.
INTRODUCTION
This Section provides information for TL1 commands that apply to the Total Access 1500 system.
2.
SYNTAX
A colon (:) separates the fields of a TL1 command. The colon also separates unused or empty fields from
required fields in a TL1 command. A comma (,) separates data entry items within a parameter block, a
keyword block, and a state block. A semicolon (;) indicates the end of a TL1 command.
NOTE
The carriage return does not indicate the end of a TL1 command.
3.
NOTATIONS AND CONVENTIONS
The following notations and conventions are used for TL1 commands:
< >, Information inside of the less than and greater than symbols indicates a data entry item for a
command. The symbols are not transmitted as part of the command.
[ ], Information inside of brackets indicates the parameter is optional for a command. The brackets are not
transmitted as part of the command.
{|}, Information inside of braces and separated by a pipe indicates that one of the parameters must be
selected from the list. The braces are not transmitted as part of the command.
The TL1 Input commands are not case sensitive. This document presents the commands and response
parameters in all uppercase as a documentation standard/convention.
4.
GENERAL FORMAT
A TL1 input command for the Total Access 1500 system has the following general format:
<verb>:<tid>:<aid>:<ctag>:<general block>:<parameter block>:<keyword block>:<state block>;
Table 2-1 provides a description for each field. Appendix A, Input Commands Data Dictionary, and
Appendix B, Response Messages Data Dictionary, contains additional information about the parameters
used with TL1 commands and response messages to the TL1 commands.
61180008L1-35A
2-1
Section 2, TL1 Commands
Total Access 1500 System TL1 Reference Guide
Table 2-1. TL1 Input Command General Format Descriptions
Field
Description
<verb>
This field contains the TL1 command verb. The command verb indicates the action
that is to be performed at the Total Access 1500 system shelf. The command verb can
have up to two optional modifiers. The valid forms are VERB, VERB-MODIFIER,
and VERB-MODIFIER-MODIFIER.
<tid>
This field indicates the TID or may be left empty. Refer to the Target Identifier (TID)
subsection.
<aid>
Refer to Section 3, ADTRAN AID Formats, for additional information.
<ctag>
The Correlation Tag (CTAG) is a one-to-six alphanumeric identifier that is echoed in
the response message for a TL1 command. The CTAG correlates input commands
with response messages. All response messages to a single TL1 command must have
the same CTAG.
<general block>
This field is not used in this application and should be left empty. This field requires
entering a field separator unless the <ctag> field is the last required field.
<parameter>
This field contains data that applies to specific TL1 commands. Refer to the specific
TL1 command sections and to applicable data dictionary appendices in this document
for additional information.
<keyword block>
Except for the CONN-LPACC-MET TL1 command, this field is not used.
<state block>
This field is not used in this application and should be left empty.
:
Field separator
;
TL1 command terminator. The command terminator may be used after the last nonempty field without supplying the remaining colon separators.
Target Identifier (TID)
The TID is a unique identifier assigned to each shelf by TIRKS. The TID can be up to 20 alphanumeric
characters. The first character must be an alpha character.
Common Language Location Identifier (CLLI)
The CLLI code can also be used as the TID in TL1 commands. The CLLI code is one-to twenty-alphanumeric characters that are not case sensitive. The CLLI code identifies physical locations and equipment
such as buildings, central offices, antennae, channel banks, and shelves. CLLI codes are also used as
unique identifiers for a single NE. The following example provides a CLLI code.
HTVLALEXD16
Where:
HTVL The first four characters identify the place name (Huntsville).
AL
The next two characters identify the state, region, or territory (Alabama).
EX
The next two characters identify the central office location code. These characters
typically identify the street location of the specific central office (In this example,
2-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
D
16
5.
Section 2, TL1 Commands
EX represents Explorer Blvd).
The next single alpha character is the equipment type code. The equipment type
code of D identifies general administrative equipment.
The last two numeric characters represent a unique identifier number for a specific
central office. These characters identify which NE is being addressed.
ACKNOWLEDGMENT RESPONSES
If an NE cannot send a normal response or an error response to the OS/user within two seconds of
receiving a TL1 command, the NE sends an acknowledgment response of IP.
Acknowledgment Syntax
The syntax for the acknowledgment responses supported by the Total Access 1500 system are as follows:
IP[^<CTAG>] <cr> <lf>
<
OK[^<CTAG>] <cr> <lf>
<
6.
NORMAL RESPONSE MESSAGES
Response Syntax
The TL1 response message for the Total Access 1500 system has the following format:
<cr> <lf> <lf>
^^^<source identifier>^<date>^<time> <cr> <lf>
M^^<ctag>^<code> <cr> <lf>
^^^<error_code> <cr> <lf>
;
Table 2-2 provides a description for each field.
Table 2-2. TL1 Response Message Format Descriptions
Field or Symbol
Description
<cr>
Carriage Return
<lf>
Line Feed
Caret (^)
The Caret represents one space character in the acknowledgment or response message.
<source identifier>
The Source Identifier (SID) indicates the unique identifier for a shelf assigned by TIRKS
or, the SID indicates the CLLI code for the shelf.
<date>
The Date field is in the form YY-MM-DD.
61180008L1-35A
2-3
Section 2, TL1 Commands
Total Access 1500 System TL1 Reference Guide
Table 2-2. TL1 Response Message Format Descriptions
Field or Symbol
Description
<time>
The Time field is in the form HH-MM-SS.
<ctag>
The Correlation Tag (CTAG) corresponds to the CTAG from the TL1 input command.
<code>
The Code field indicates the transaction status for the TL1 input command.
COMPLD indicates normal completion.
DENY indicates an error condition.
<error_code>
The Error Code appears after a DENY condition. Refer to Appendix C, Error Codes, for
applicable error codes.
7.
TOTAL ACCESS 1500 SYSTEM TL1 COMMANDS
Table 2-3 provides TL1 command categories for the Total Access 1500 system.
Table 2-3. Total Access 1500 TL1 Commands
Common (SCU)
Security
Surveillance
System Maintenance
ACT-USER
CANC-USERSECU
ALW-MSG
CHG-SPLIT
ACT-USER
CANC-USERSECU
ALW-MSG
CHG-SPLIT
CANC-USER
INH-MSG
CHG-SPLIT-LILO
RTRV-SYS
RTRV-ALM
CONN-LPACC-MET
RTRV-VERSION
RTRV-COND
CONN-MON
RTRV-HDR
CONN-TACC-MET
RTRV-PM-T1
DISC-TACC
SCHEDPMREPT-T1
OPR-LPBK-TST
REPT-STAT
RLS-LPBK-TST
RST-TAP-MET
MTA TL1 Commands
The System Maintenance TL1 commands also apply to Metallic Test Access (MTA).
2-4
61180008L1-35A
Section 3
ADTRAN AID Formats
1.
INTRODUCTION
This Section provides information about ADTRAN AID formats for the Total Access 1500 system.
2.
ADTRAN AID STRUCTURE
The AID parameter for the Total Access 1500 system consists of a hierarchy-based format.
The AID structure for a TL1 command has the following general formats:
“shelf-digroup-slot” for the SCU, the LIU, and the PSU cards.
“shelf-digroup-slot-port” for Quad, Dual, and Single line cards.
Shelf
Th shelf number, assigned by TIRKS, identifies the targeted SCU for the TL1 command. The shelf number
for the Total Access 1500 system is fixed at 1 in the current software release.
Digroup
The digroup number has a range from 1 to 5.
For T1 alarms, the digroup number identifies the T1 and has a range from 1 to 5. T1 number 5 is the protect
line in SLC 96 mode.
Slot
The slot number for the SCU is 0.
LIU-A is slot 25. LIU-B is slot 26.
PSU-A is slot 28. PSU-B is slot 29.
The slot number for environmental alarms (local shelf) is 30.
The slot number for environmental alarms (remote shelf) is 31.
The slot number for the PSU-A (remote shelf) is 32.
The slot number for the PSU-B (remote shelf) is 33.
The slot number for the SCU (remote shelf) is 34.
The slot number for the LIU-A (remote shelf) is 35.
The slot number for the LIU-B (remote shelf) is 36.
The slot number for line cards has a range from 1 to 24.
61180008L1-35A
3-1
Section 3, ADTRAN AID Formats
Total Access 1500 System TL1 Reference Guide
Port
The port number applies to line cards. The range of values for the port number depends on which line card
is being targeted by the AID parameter in the TL1 command. The specific TL1 input command and the
targeted NE determines when the AID parameter requires the port number.
There are no spaces between the parts of the AID parameter. Leading zeros are not significant. They are
ignored on input and suppressed on output.
Table 3-1 provides some examples of AID parameters.
Table 3-1. Total Access 1500 AID Parameter Examples
AID
Description
1-1-0
Shelf 1, digroup 1, slot 0 (addresses the SCU, slot = 0)
1-3-25
Shelf 1, digroup 3, slot 25 (addresses T1 number 3 and LIU-A, slot = 25)
1-1-23-4
Shelf 1, digroup 1, slot 23, port 4 (addresses T1 number 1, port 4 for the line card in slot 23)
Entity Type
Whether an AID is required for a TL1 input command may depend on the entity type being addressed by
the TL1 command. The entity type is expressed as a modifier in the verb part of the TL1 input command.
The command verb formats for the entity types include VERB-MODIFIER and VERB-MODIFIERMODIFIER.
The Total Access 1500 system supports the following entity types:
EQPT
This command verb modifier indicates the equipment unit. An equipment unit can be the
entire NE or a single element such as a circuit card.
T1
This command verb modifier indicates a facility or circuit.
TST
This command verb modifier indicates test access.
ENV
This command verb modifier indicates environmental data is being retrieved.
ALL
This command verb modifier indicates all entity types within the NE.
Card Type
This subsection provides information about the LIU card within a Total Access 1500 system. This
subsection also provides a table that references appendices in this document for information about line
cards that apply to the Total Access 1500 system.
NOTE
The PSU does not support TL1 commands. The SCU handles TL1 data,
such as alarms, for the PSU.
3-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Section 3, ADTRAN AID Formats
LIU
The LIU card that occupies either slot 25 (A) or 26 (B) uses the following AID format: shelf-digroup-slot.
The slot number for an LIU card is always 25 or 26 and depends on whether the LIU card is located in
LIU-A or LIU-B in the shelf. LIU A is slot 25, and LIU B is slot 26. Figure 3-1 shows an example of the
slot numbers for the LIU card.
Line Access Module
1500
SCU
1180008L2
3
3
3
3
A
M
P
A
M
P
A
M
P
A
M
P
T
I
M
I
N
G
C
R
A
F
T
MJR
HST
MNR
MLT
BSY
PWR
PWR
FAIL
FAIL
RMT
20Hz
20Hz
ACO
LIU
LIU
1180109L1
1180109L1
A
R
A
R
C
D
C
D
P
RED
P
RED
YEL
RCV
YEL
RCV
REM
TEST
REM
TEST
MASTER
STATUS
MONITOR
PSU-A
PSU-B
SCU
LIU-A
PSU
28
PSU
29
SCU
0
LIU
25
MASTER
FXS/DPO
FXS/DPO
FXS/DPO
1180403L1
1180403L1
1180403L1
FXS/DPO
1180403L1
STATUS
STATUS
STATUS
STATUS
REM
REM
REM
REM
AP
AP
AP
AP
STATUS
TX
TX
RX
RX
MONITOR
LIU-B
LIU
26
1
2
3
1
2
3
24
24
Figure 3-1. Card Slot Numbers Example
Alarms
For alarms and alarm condition codes that apply to the LIU card, refer to Appendix D, Alarms and Alarm
Condition Codes.
TL1 Commands
The Surveillance TL1 commands apply to the LIU. Refer to Section 6, Surveillance TL1 Commands, for
additional information about these commands.
Line Cards
Table 3-2 provides information about the line cards that apply to the Total Access 1500 system. Refer to
the appropriate Appendix in this document for information about each line card.
Table 3-2. Total Access 1500 Line Cards Reference Data
Line Card
Appendix
Quad Line Cards
Appendix F- Quad-Port Line Cards
Dual Line Cards
Appendix G - Dual-Port Line Cards
Single Line Cards
Appendix H - Single-Port Line Cards
61180008L1-35A
3-3
Section 3, ADTRAN AID Formats
3-4
Total Access 1500 System TL1 Reference Guide
61180008L1-35A
Section 4
Common (SCU) TL1 Commands
1.
INTRODUCTION
The following TL1 commands apply to the SCU or apply to the Total Access 1500 system:
•
•
•
•
ACT-USER
CANC-USER
RTRV-SYS
RTRV-VERSION
2.
ACT-USER
The ACT-USER (Activate-User) command allows access to the Total Access 1500 system from a local or
remote terminal. The user must have a valid User ID (UID) and password.
Input Format
ACT-USER:[<TID>]:<USER>:[<CTAG>]::<PASSWORD>;
Example:
ACT-USER:HTVLALEXD0101:USER1:1::PASSWORD1;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
USER
This parameter indicates the User ID or logon name for the user. This
parameter can have up to 10 alphanumeric characters. Valid
characters are A-Z and 0-9.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
PASSWORD
This parameter contains the private ID for the user. The password
consists of an alphanumeric character string with a maximum length
of 10 characters. Valid characters are A-Z and 0-9.
61180008L1-35A
4-1
Section 4, Common (SCU) TL1 Commands
Total Access 1500 System TL1 Reference Guide
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 1
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-05-30 13:28:03
M 1 COMPLD
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
4-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
3.
Section 4, Common (SCU) TL1 Commands
CANC-USER
The CANC-USER (Cancel-User) command terminates a TL1 session.
Input Format
CANC-USER:[<TID>]:[<USER>]:[<CTAG>];
Example:
CANC-USER:HTVLALEXD0101:USER1:5;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
USER
This parameter indicates the User ID or logon name for the user. This
parameter can have up to 10 alphanumeric characters.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 5
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-05-30 16:36:54
M 5 COMPLD
;
61180008L1-35A
4-3
Section 4, Common (SCU) TL1 Commands
Total Access 1500 System TL1 Reference Guide
Error Response
<cr> <lf> <lf>
^^^<SID>^YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary for Normal Response and Error Response
parameter descriptions.
4-4
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
4.
Section 4, Common (SCU) TL1 Commands
RTRV-SYS
The RTR-SYS (Retrieve System) command provides the type of Total Access system.
Input Format
RTRV-SYS:[<TID>]::[<CTAG>];
Example:
RTRV-SYS:HTVLALEXD0101::26;
Input Parameters
TID
The Target Identifier (TID) parameter identifies the target NE for the
command. Refer to the Target Identifier (TID) subsection in Section
2, TL1 Commands, for additional information.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 26
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-05-31 15:47:20
M 26 COMPLD
"::TYPE=TA1500"
;
61180008L1-35A
4-5
Section 4, Common (SCU) TL1 Commands
Total Access 1500 System TL1 Reference Guide
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary for Normal Response and Error Response
parameter descriptions.
4-6
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
5.
Section 4, Common (SCU) TL1 Commands
RTRV-VERSION
The RTRV-VERSION (Retrieve Version) command instructs an NE to return its SCU software version.
Input Format
RTRV-VERSION:[<TID>]::[<CTAG>];
Example:
RTRV-VERSION:HTVLALEXD0101::28;
Input Parameters
TID
The Target Identifier (TID) parameter identifies the target NE for the
command. Refer to the Target Identifier (TID) subsection in Section
2, TL1 Commands, for additional information.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 28
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
^^^"<SW Rev.>" <cr> <lf>
;
Example:
HTVLALEXD0101 02-05-31 15:52:08
M 28 COMPLD
"::VERSION=S04.00"
;
61180008L1-35A
4-7
Section 4, Common (SCU) TL1 Commands
Total Access 1500 System TL1 Reference Guide
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
4-8
61180008L1-35A
Section 5
Security TL1 Commands
1.
INTRODUCTION
These Security TL1 commands allow an administrator to cancel, delete, edit, enter (add), and retrieve
security information for a user account. At the present, only the CANC-USER-SECU Security TL1
command applies to the Total Access 1500 system.
2.
CANC-USER-SECU
The CANC-USER-SECU (Cancel User Security) TL1 command allows an administrator to log off the user
of an active TL1 session. This command is used to log off unauthorized users of the Total Access 1500
system.
Input Format
CANC-USER-SECU:[<TID>]:<AID>:[<CTAG>];
Example:
CANC-USER-SECU:HTVLALEXD0101:USER1:4;
Input Parameters
TID
The Target Identifier (TID) parameter identifies the target NE for the
command. Refer to the Target Identifier (TID) subsection in Section
2, TL1 Commands, for additional information.
AID
The Access Identifier (AID) parameter indicates the User ID (UID) of
the user whose session is being terminated. The AID parameter may
be a single UID.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
61180008L1-35A
5-1
Section 5, Security TL1 Commands
Total Access 1500 System TL1 Reference Guide
Example:
IP 4
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-06-04 09:03:52
M 4 COMPLD
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
5-2
61180008L1-35A
Section 6
Surveillance TL1 Commands
1.
INTRODUCTION
The following Surveillance TL1 commands apply to the Total Access 1500 system:
•
•
•
•
•
•
•
2.
ALW-MSG
INH-MSG
RTRV-ALM
RTRV-COND
RTRV-HDR
RTRV-PM-T1
SCHED-PMREPT-T1
ALW-MSG
The ALW-MSG (Allow-Message) command enables an NE to transmit autonomous messages to an
Operations System (OS). This command has the following format for the command verb:
ALW-MSG-{T1|EQPT|ALL}. T1, EQPT, or ALL may be used as the second modifier. The value entered
for the <NTFCNCDE> parameter determines which autonomous messages are sent by the NE.
The INH-MSG (Inhibit-Message) command inhibits the transmission of autonomous messages to an OS.
Refer to the INH-MSG command in this section for additional information.
Refer to Appendix E, Autonomous Messages, for additional information.
Input Format
ALW-MSG-{T1|EQPT|ALL}:[<TID>]:<null>:[<CTAG>]::[<NTFCNCDE>];
Example:
ALW-MSG-EQPT:HTVLALEXD0101::2::MJ;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
Null
Null indicates an empty field.
61180008L1-35A
6-1
Section 6, Surveillance TL1 Commands
Total Access 1500 System TL1 Reference Guide
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
NTFCNCDE
The Notification Code (NTFCNCDE). Refer to Appendix A, Input
Commands Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 2
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-11-01 12:19:02
M 2 COMPLD
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
6-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
3.
Section 6, Surveillance TL1 Commands
INH-MSG
The INH-MSG (Inhibit-Message) command instructs an NE to inhibit the sending of autonomous
messages from an NE to OS/user. This command has the following format for the command verb:
INH-MSG-{T1|EQPT|ALL}. T1, EQPT, or ALL may be used as the second modifier. The value entered
for the <NTFCNCDE> parameter determines which autonomous messages are inhibited. This command
only applies to the OS/user TL1 session from which the command is sent.
To resume the sending of autonomous messages, refer to the ALW-MSG command in this Section.
Input Format
INH-MSG-{T1|EQPT|ALL}:[<TID>]:<null>:[<CTAG>]::[<NTFCNCDE>];
Example:
INH-MSG-T1:HTVLALEXD0101::13::MJ;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
Null
Null indicates an empty field.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
NTFCNCDE
The Notification Code (NTFCNCDE). Refer to Appendix A, Input
Commands Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 13
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
61180008L1-35A
6-3
Section 6, Surveillance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Example:
HTVLALEXD0101 02-11-01 17:15:51
M 13 COMPLD
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
6-4
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
4.
Section 6, Surveillance TL1 Commands
RTRV-ALM
The RTRV-ALM-(Retrieve-Alarm) TL1 command instructs an NE to retrieve and send the current status
of its alarm conditions associated with one or more of its entities.
The command may be used to retrieve NE information, which in turn may be used to update an OS
database when it is suspected that autonomous alarm messages issued by the NE were not received or
properly processed. This command may also be used to evaluate the system before or after NE maintenance operations.
The command has the following format for the command verb:
RTRV-ALM-{T1|EQPT|ALL|ENV}. T1, EQPT, ALL, or ENV may be used as the second modifier.
Input Format
RTRV-ALM-{T1|EQPT|ALL|ENV}:[<TID>]:[<AID>]:[<CTAG>]::[<NTFCNCDE>];
Example:
RTRV-ALM-T1:HTVLALEXD0101:1-1-25:19::MJ;
Input Parameters
TID
The Target Identifier (TAG) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
AID
The Access Identifier (AID) identifies the entity within the NE to
which the desired alarm conditions pertain. Refer to Section 3,
ADTRAN AID Formats, for additional information.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
NTFCNCDE
The Notification Code (NTFCNCDE). Refer to Appendix A, Input
Commands Data Dictionary, for additional information
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 19
<
61180008L1-35A
6-5
Section 6, Surveillance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Normal Response
Format for no Alarm Conditions
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Format for Alarm Conditions
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
<rspblk> + ;
<rspblk> has the following format (+ denotes one or more):
^^"[<AID>][,<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],
[<OCRTM>],[<LOCN>],,{<TMPER>]" <cr> <lf>
Example:
HTVLALEXD0101 02-11-01 12:30:30
M 19 COMPLD
"1-1-25,T1:MJ,LOS,SA,15-02,35-01-35,,,"
"1-2-25,T1,MJ,LOS,SA,15-02,35-01-35,,,"
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
6-6
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
5.
Section 6, Surveillance TL1 Commands
RTRV-COND
The RTRV-COND (Retrieve Condition) command instructs an NE to return the current standing condition
or state associated with one or more equipment units, transmission types, or test access within the NE. This
command has the following format for the command verb:
RTRV-COND-{T1|EQPT|TST|ALL}. T1, EQPT, TST, or ALL may be used as the second modifier.
Input Format
RTRV-COND-{T1|EQPT|TST|ALL}:[<TID>]:[<AID>]:[<CTAG>];
Example:
RTRV-COND-ALL:HTVLALEXD0101::22;
Input Parameters
TID
The Target Identifier (TID) parameter identifies the target NE for the
command. Refer to the Target Identifier (TID) subsection in Section
2, TL1 Commands, for additional information.
AID
The Access Identifier (AID) parameter identifies the slot location for
the entity within the NE from which data is being retrieved. The AID
format for this command is shelf-digroup-slot. Refer to Section 3,
ADTRAN AID Formats, for additional information.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 22
<
61180008L1-35A
6-7
Section 6, Surveillance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Normal Response
If there are no conditions to report, the format is as follows:
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
If there is at least one condition to report, the format is as follows (+ denotes one or more):
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
<rspblk> + ;
<rspblk> has the following format:
^^^"<AID>[,<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>],
[<OCRTM>],[<LOCN>],,[<TMPER>]" <cr> <lf>
Example:
HTVLALEXD0101 02-11-01 12:37:53
M 22 COMPLD
"1-1-25,T1:MJ,LOS,SA,15-02,35-01-35,,,"
"1-2-25,T1:MJ,LOS,SA,15-02,35-01-35,,,"
"1-1-26,EQPT:MN,CTNEQPT,NSA,15-02,35-01-36,,,"
"1-1-28,EQPT:MJ,RT,SA,15-02,35-02-01,,,"
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
6-8
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
6.
Section 6, Surveillance TL1 Commands
RTRV-HDR
The RTRV-HDR (Retrieve-Header) command instructs the NE to reply with a normal response that
indicates COMPLD. The information of interest is the reply itself along with information the NE has about
itself that includes the <SID>, the <DATE>, the <TIME>, and the software version.
Input Format
RTRV-HDR:[<TID>]::[<CTAG>];
Example:
RTRV-HDR:HTVLALEXD0101::23;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 23
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
^^^/*<SW Rev.> */ <cr> <lf>
;
Example:
HTVLALEXD0101 02-11-01 12:39:25
M 23 COMPLD
/* Version S04.00 */
;
61180008L1-35A
6-9
Section 6, Surveillance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
6-10
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
7.
Section 6, Surveillance TL1 Commands
RTRV-PM-T1
The RTRV-PM-T1 (Retrieve Performance Monitoring T1) command instructs an NE to send its current set
of Performance Monitoring (PM) data for type T1.
The data may be used to load an OS or audit an OS database when it is suspected that autonomous PM
messages were not received or properly processed. This command may also be used to evaluate the system
before or after NE maintenance operations.
Input Format
RTRV-PM-T1:[<TID>]:<AID>:[<CTAG>]::,[<MONLEV>],[<LOCN>],,[<TMPER>],[<MONDAT>],
[<MONTM>];
Example:
RTRV-PM-T1:HTVLALEXD0101:1-1-25:41::,ESL,SESL,UASP,NEND,,1-DAY,11-01,00-00;
Input Parameters
TID
The Target Identifier (TID) parameter identifies the target NE for the
command. Refer to the Target Identifier subsection in Section 2, TL1
Commands, for additional information.
AID
The Access Identifier (AID) parameter identifies the slot location for
the entity within the NE where the data is being retrieved. Refer to
Section 3, ADTRAN AID Formats, for additional information.
CTAG
The Correlation Tag (CTAG).
MONLEV
The Monitor Level (MONLEV).
LOCN
The Location (LOCN).
TMPER
The Time Period (TMPER).
MONDAT
The Monitor Date (MONDAT).
MONTM
The Monitor Time (MONTM).
Refer to Appendix A, Input Commands Data Dictionary, for additional information about the Input
Parameters.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
61180008L1-35A
6-11
Section 6, Surveillance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Example:
IP 41
<
Normal Response
If the NE does not have any PM values to report, the following format applies:
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
If the NE has one or more PM values to report, the following format applies (+ denotes one or more):
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
<rspblk> + ;
<rspblk> has the following format:
^^^"<AID>:<MONTYPE>,<MONVAL>,[<VLDTY>],[<LOCN>],,[<TMPER>],[<MONDAT>]
[,<MONTM>]" <cr> <lf>
Example:
HTVLALEXD0101 02-11-01 12:44:32
M 41 COMPLD
"1-1-25:ESL,7374,PRTL,NEND,,1-DAY,11-01,00-00"
"1-1-25:SESL,7374,PRTL,NEND,,1-DAY,11-01,00-00"
"1-1-25:UASP,7386,PRTL,NEND,,1-DAY,11-01,00-00"
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
6-12
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
8.
Section 6, Surveillance TL1 Commands
SCHED-PMREPT-T1
The SCHED-PMREPT-T1 (Schedule Performance Monitoring Report-T1) command instructs an NE to
start, reschedule, or remove the reporting of performance-monitoring data for type T1.
When this command is used, it is expected that the NE periodically returns data to the OS/user with the
automatic Report Performance Monitoring message.
Input Format
SCHED-PMREPT-T1:[<TID>]:<AID>:[<CTAG>]::[<REPTINVL>],[<REPTSTATM],[<NUMREPT>],,
[<MONLEV>],[<LOCN>],,[<TMPER>],[<TMOFST>];
Example:
SCHED-PMREPT-T1:HTVLALEXD0101:1-1-25:1::15-MIN,21-0,,,0-UP,NEND,,15-MIN,0-0-0;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
AID
The Access Identifier (AID) identifies the entity within the NE from
which data is being retrieved. Refer to Section 3, ADTRAN AID
Formats, in this document for additional information.
CTAG
The Correlation Tag (CTAG).
REPTINVL
The Report Interval (REPTINVL).
REPTSTATM
The Report Starting Time (REPTSTATM).
NUMREPT
The Number of Reports (NUMREPT).
MONLEV
The Monitoring Level (MONLEV).
LOCN
The Location (LOCN).
TMPER
The Time Period (TMPER).
TMOFST
The Time Offset (TMOFST).
Refer to Appendix A, Input Commands Data Dictionary, for additional information about the Input
Parameters.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
61180008L1-35A
6-13
Section 6, Surveillance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Example:
IP 1
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-11-01 12:44:31
M 1 COMPLD
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
6-14
61180008L1-35A
Section 7
System Maintenance TL1 Commands
1.
INTRODUCTION
The following System Maintenance TL1 commands apply to the Total Access 1500 system:
•
•
•
•
•
•
•
•
•
•
CHG-SPLIT
CHG-SPLIT-LILO
CONN-LPACC-MET
CONN-MON
CONN-TACC-MET
DISC-TACC
OPR-LPBK-TST
REPT-STAT
RLS-LPBK-TST
RST-TAP-MET
The System Maintenance TL1 commands apply to MTA.
2.
CHG-SPLIT
The CHG-SPLIT (Change Split) command instructs the NE to provide the necessary connections to the
Test Access Path (TAP) and split, at the access point, the pair or pairs specified by the access command of
the circuit under test.
Input Format
CHG-SPLIT:[<TID>]:<TAP>:[<CTAG>];
Example:
CHG-SPLIT:HTVLALEXD0101:10:15;
Input Parameters
TID
61180008L1-35A
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
7-1
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
TAP
The Test Access Path (TAP). This parameter indicates the test access
path number selected by either the NE or Test System Controller
(TSC). The assigned TAP number is echoed back in the response
message of the initial “connect test access” message. Thereafter, the
TAP parameter is used to identify all messages between the TSC and
the NE until the access point is released. Range of values for this
parameter is 1 to 48.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 15
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-11-01 15:45:20
M 15 COMPLD
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
7-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
3.
Section 7, System Maintenance TL1 Commands
CHG-SPLIT-LILO
The CHG-SPLIT-LILO (Change Split Look In Look Out) TL1 command provides the connections to the
TAP and splits the circuit under test. This command only applies to NEs that provide non-simultaneous
split access. This command does not apply to NEs that support a full splitting access.
Input Format
CHG-SPLIT-LILO:[<TID>]:<TAP>:[<CTAG>]::<DIR>;
Example:
CHG-SPLIT-LILO:HTVLALEXD0101:1:1::E;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
TAP
The Test Access Path (TAP). This parameter indicates the test access
path number selected by either the NE or Test System Controller
(TSC). The assigned TAP number is echoed back in the response
message of the initial “connect test access” message. Thereafter, the
TAP parameter is used to identify all messages between the TSC and
the NE until the access point is released. Range of values for this
parameter is 1 to 48.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
DIR
The Direction (DIR) parameter indicates the direction of
transmission of the test signal. E indicates Equipment direction. F
indicates Facility direction.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 1
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
61180008L1-35A
7-3
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Example:
HTVLALEXD0101 02-11-01 15:15:45
M 1 COMPLD
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
7-4
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
4.
Section 7, System Maintenance TL1 Commands
CONN-LPACC-MET
The CONN-LPACC-MET (Connect Loop Around Access Metallic) command controls the Test Access
Path (TAP), access point designation, and TAP loop around. This command provides the information
required for the metallic NE or Metallic Test Access Unit (MTAU) to gain test access to a particular circuit.
This command also has the information required to provide a loop around on the selected TAP.
Input Format
CONN-LPACC-MET:<TID>:<AID>:<CTAG>::[<TAP>]:<CNFGRN>;
Example:
CONN-LPACC-MET:HTVLALEXD0101:1-1-3-2:20::4:2WA;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
AID
The Access Identifier (AID) identifies the entity within the NE.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
TAP
The Test Access Path (TAP). This parameter indicates the test access
path number selected by either the NE or Test System Controller
(TSC). The assigned TAP number is echoed back in the response
message of the initial “connect test access” message. Thereafter, the
TAP parameter is used to identify all messages between the TSC and
the NE until the access point is released. Range of values for this
parameter is 1 to 48.
CNFGRN
The Configuration Code (CNFGRN). For metallic access, this
parameter defines the access point lead-pair usage configuration.
Refer to Appendix A, Input Commands Data Dictionary, for
additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 20
<
61180008L1-35A
7-5
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
^^^<TAP>
;
Example:
HTVLALEXD0101 02-10-30 16:34:
M 20 COMPLD
4
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
7-6
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
5.
Section 7, System Maintenance TL1 Commands
CONN-MON
The CONN-MON (Connect Monitor) command establishes a monitor state without having to reaccess the
circuit under test.
Input Format
CONN-MON:[<TID>]:<TAP>:[<CTAG>];
Example:
CONN-MON:HTVLALEXD0101:2:10;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
TAP
The Test Access Path (TAP). This parameter indicates the test access
path number selected by either the NE or Test System Controller
(TSC). The assigned TAP number is echoed back in the response
message of the initial “connect test access” message. Thereafter, the
TAP parameter is used to identify all messages between the TSC and
the NE until the access point is released. Range of values for this
parameter is 1 to 48.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 10
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
^^^<TAP>
;
61180008L1-35A
7-7
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Example:
HTVLALEXD0101 02-11-01 11:45:35
M 10 COMPLD
2
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
7-8
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
6.
Section 7, System Maintenance TL1 Commands
CONN-TACC-MET
The CONN-TACC-MET (Connect Test Access Metallic) command enables the NE to provide a monitor
connection to the transmission pairs of a circuit and complete circuit access.
This command removes the TAP loop around, and connects the appropriate TAP lead pairs to the access
point. The circuit access number (address) is found in the CONN-LPACC-MET command, which must be
successfully transmitted before the CONN-TACC-MET command.
Input Format
CONN-TACC-MET:[<TID>]:<TAP>:[<CTAG>];
Example:
CONN-TACC-MET:HTVLALEXD0101:4:21;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information..
TAP
The Test Access Path (TAP). This parameter indicates the test access
path number selected by either the NE or Test System Controller
(TSC). The assigned TAP number is echoed back in the response
message of the initial “connect test access” message. Thereafter, the
TAP parameter is used to identify all messages between the TSC and
the NE until the access point is released. Range of values for this
parameter is 1 to 48.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 21
<
61180008L1-35A
7-9
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-09-19 14:35:
M 21 COMPLD
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
7-10
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
7.
Section 7, System Maintenance TL1 Commands
DISC-TACC
The DISC-TACC (Disconnect Test Access Metallic) dual application command causes the NE to restore
the circuit under test to its through state and open all TAP connections to that access point.
At a Test System Controller/Remote Test Unit [TSC/RTU], this command causes the release of resources
and retires the corresponding Test Session Number (TSN) specified.
The sequence of release must restore the access point before opening TAP connections. The TAP is to be
returned to the idle state when test access is removed.
Input Format
DISC-TACC:[<TID>]:<TAP>:<CTAG>;
Example:
DISC-TACC:HTVLALEXD0101:4:22;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
TAP
The Test Access Path (TAP). This parameter indicates the test access
path number selected by either the NE or Test System Controller
(TSC). The assigned TAP number is echoed back in the response
message of the initial “connect test access” message. Thereafter, the
TAP parameter is used to identify all messages between the TSC and
the NE until the access point is released. Range of values for this
parameter is 1 to 48.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 22
<
61180008L1-35A
7-11
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Normal Response
<cr> <lf> <lf>
^^^<SID^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-10-30 15:29:53
M 22 COMPLD
;
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
7-12
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
8.
Section 7, System Maintenance TL1 Commands
OPR-LPBK-TST
The OPR-LPBK-TST (Operate Loopback Test) command instructs an NE to operate a loopback on a
specified TAP associated with a test access session in the NE.
Input Format
OPR-LPBK-TST:[<TID>]:<AID>:[<CTAG>];
Example:
OPR-LPBK-TST:HTVLALEXD0101:1-1-25:4;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
AID
The Access Identifier (AID) identifies the test access in the NE.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 4
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-10-30 14:30:35
M 4 COMPLD
;
61180008L1-35A
7-13
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
^^^<CTAG> DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
7-14
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
9.
Section 7, System Maintenance TL1 Commands
REPT-STAT
The REPT-STAT (Report Status) command is sent from the Test System Controller (TSC)/Remote Test
Unit (RTU) [TSC/RTU], to an NE. The command is used to check that the data link between the TSC/RTU
and NE is in operation.
If the NE does not receive a command from the TSC/RTU for a period of 75 seconds, it drops the data link
connection.
Only an OK acknowledgment response is expected for this command.
Input Format
REPT-STAT:[<TID>]:<Null>:[<CTAG>];
Example:
REPT-STAT:HTVLALEXD0101::17;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information..
Null
Null indicates an empty field.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
OK^<CTAG> <cr> <lf>
<
Example:
OK 17
<
Normal Response
A normal response is not expected for the REPT-STAT command.
61180008L1-35A
7-15
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Error Response parameter descriptions.
7-16
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Section 7, System Maintenance TL1 Commands
10. RLS-LPBK-TST
The RLS-LPBK-TST (Release Loopback Test) command instructs an NE to release loopback on a
specified test access.
Input Format
RLS-LPBK-TST:[<TID>]:<AID>:[<CTAG>];
Example:
RLS-LPBK-TST:HTVLALEXD0101:1-1-25:7;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information..
AID
The Access Identifier (AID) identifies the test access in the NE.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 7
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-10-30 16:30:29
M 7 COMPLD
;
61180008L1-35A
7-17
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
7-18
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Section 7, System Maintenance TL1 Commands
11. RST-TAP-MET
The RST-TAP-MET (Restore Test Access Paths Metallic) command releases all existing test access
connections in the NE that were established by an OS over its control link.
Input Format
RST-TAP-MET:[<TID>]:[ALL]:[<CTAG>];
Example:
RST-TAP-MET:HTLALEXD0101:ALL:25;
Input Parameters
TID
The Target Identifier (TID) identifies the target NE for the command.
Refer to the Target Identifier (TID) subsection in Section 2, TL1
Commands, for additional information.
ALL
ALL represents all existing test access and TAP connections (assignments) in the NE.
CTAG
The Correlation Tag (CTAG). Refer to Appendix A, Input Commands
Data Dictionary, for additional information.
Response Format
Acknowledgment
IP^<CTAG> <cr> <lf>
<
Example:
IP 25
<
Normal Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^COMPLD <cr> <lf>
;
Example:
HTVLALEXD0101 02-09-19 15:35:30
M 25 COMPLD
;
61180008L1-35A
7-19
Section 7, System Maintenance TL1 Commands
Total Access 1500 System TL1 Reference Guide
Error Response
<cr> <lf> <lf>
^^^<SID>^<YY-MM-DD>^<HH:MM:SS> <cr> <lf>
M^^<CTAG>^DENY <cr> <lf>
^^^<error_code> <cr> <lf>
;
Refer to Appendix B, Response Messages Data Dictionary, for Normal Response and Error Response
parameter descriptions.
7-20
61180008L1-35A
Appendix A
Input Commands Data Dictionary
1.
INTRODUCTION
Table A-1 provides descriptions for the parameters that may be used in a TL1 input command for the Total
Access 1500 system.
Table A-1. Total Access 1500 TL1 Input Commands Data Dictionary
Parameter
Description
AID
Access Identifier. Refer to Section 3, ADTRAN AID Formats, for information.
CNFGRN
For metallic access, the Configuration Code parameter defines the access point lead-pair
usage configuration. Acceptable configuration code and definitions include:
2WA 2-wire circuit on A pair of access point
4AB or 4BA 4-wire circuit on A and B pairs of access point
2EM 2-wire circuit on A pair with E&M signaling on B pair
DAB or DBA 4-wire circuit on A and B pairs at the DS0A level
CTAG
The Correlation Tag associates the input command with the response message(s). The
CTAG contains 1- to 6 alphanumeric characters. The CTAG is echoed in the response
message to the input command. For example, an input command with a CTAG of 1 has a
response message with a CTAG of 1. The default is 0.
DIR
The Direction parameter indicates the transmission direction for the test signals. E
indicates Equipment direction. F indicates Facility direction.
LOCN
The Location parameter indicates the location from which an alarm condition or Performance Monitoring (PM) threshold alarm value is being reported. Valid values for the
LOCN parameter are NEND and FEND or null.
MONDAT
This parameter indicates the beginning date for the PM data specified in the TMPER
parameter. The format for the MONDAT parameter is MM-DD.
MM indicates month of year (values, 1 to 12).
DD indicates day of month (values, 1 to 31).
MONLEV
This parameter specifies the level for the requested monitor parameter. Supported values
include:
0-UP : show zero values.
1-UP : suppress zero values.
61180008L1-35A
A-1
Appendix A, Input Commands Data Dictionary
Total Access 1500 System TL1 Reference Guide
Table A-1. Total Access 1500 TL1 Input Commands Data Dictionary (Continued)
Parameter
Description
MONTM
This parameter indicates monitoring time for the storage register period specified in the
TMPER parameter. The format for the MONTM parameter is HH-MM.
HH indicates hour of day (values, 0 to 23).
MM indicates minute of hour (values, 0 to 59).
NTFCNCDE
The Notification Code parameter indicates the notification code associated with alarm
conditions. Supported values are as follows:
CR : Critical Alarm
MJ : Major Alarm
MN : Minor Alarm
SC : Standing Condition
Null
Null indicates an empty field.
NUMREPT
The Number of Reports parameter specifies the number of the reports to generate. Null
generates forever; zero stops reports.
A null value generates reports indefinitely until either stopped with a value of zero or
rescheduled with another command.
PASSWORD
This parameter provides a 1- to 10- character alphanumeric string. Valid values are A-Z
and 0-9.
REPTINVL
The Report Interval parameter specifies how often a performance-monitoring report is to
be generated and returned to the requesting OS/user. The format for REPTINVL is in the
form of nn-MIN, hh-HR, or nn-DAY.
The nn-MIN parameter indicates minutes (values, 1 to 1440).
The hh-HR parameter indicates hours (values, 1 to 24).
The nn-DAY parameter indicates day (values, 1 to 31).
REPTSTATM
The Report Starting Time parameter specifies the starting time for the performance
monitoring reporting schedule. The format for the REPTSTATM parameter is
HH-MM.
HH indicates hour of day (values, 0 to 23).
MM indicates minute of hour (values, 0 to 59).
TAP
The Test Access Path parameter identifies messages between a TSC and a NE during an
MTA test. The parameter value ranges from 1-48.
TID
Refer to the Target Identifier (TID) subsection in Section 2, TL1 Commands, for additional
information.
TMOFST
The Time Offset parameter specifies the time offset from the end of the last complete
accumulation time period to the beginning of the accumulation time period specified in the
TMPER parameter. The format for the TMOFST parameter is in the form DD-HH-MM.
DD indicates days (values, 0 to 31).
HH indicates hours (values, 0 to 23).
MM indicates minutes (values, 0 to 59).
A-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Appendix A, Input Commands Data Dictionary
Table A-1. Total Access 1500 TL1 Input Commands Data Dictionary (Continued)
Parameter
Description
TMPER
The Time Period parameter indicates the accumulation time period for Performance
Monitoring (PM) data. The format for TMPER is 15-MIN or 1-DAY.
The NE determines the default value.
USER
This parameter indicates the 1- to 10-character alphanumeric string for the user name.
Valid characters are A-Z and 0-9.
61180008L1-35A
A-3
Appendix A, Input Commands Data Dictionary
A-4
Total Access 1500 System TL1 Reference Guide
61180008L1-35A
Appendix B
Response Messages Data Dictionary
1.
INTRODUCTION
Table B-1 provides descriptions for the parameters that may be received in a response message to a TL1
input command for the Total Access 1500 system.
Table B-1. Total Access 1500 TL1 Response Messages Data Dictionary
Parameter
Description
^
ASCII space character.
+
The plus sign indicates information for the preceding field or parameter may occur one or
more times.
AID
The Access Identifier (AID) parameter in a response message indicates the location
within the NE entity from which information is being retrieved.
AIDTYPE
This parameter indicates the type of AID. T1 is an example.
COMPLD
This parameter indicates the successful execution for the input command. The
transaction was fully completed.
CONDTYPE
This parameter indicates a single type of alarm condition being reported for an entity
within the NE. Refer to Appendix D, Alarms and Alarm Condition Codes, for condition
types that apply to the Total Access 1500 system.
<cr>
ASCII carriage return.
CTAG
The Correlation Tag (CTAG) associates the input command with the response
message(s). The CTAG contains 1- to 6-alphanumeric characters. The CTAG is echoed
in the response message to the input command. For example, an input command with a
CTAG of 1 has a response message with a CTAG of 1.
DENY
This parameter indicates unsuccessful execution for the input command. The transaction
was fully denied or uncompleted.
<error_code>
The <error_code> provides a four-character mnemonic abbreviation for the error
condition. Refer to Appendix C, Error Codes, for additional information.
HH:MM:SS
This parameter is part of the response message header format where HH is hour, MM is
minute, and SS is second. Each component has two digits.
HH ranges from 00 to 23; MM ranges from 00 to 59; SS ranges from 00 to 59.
IP
This acknowledgment component indicates the action specified by the input command is
in progress.
<lf>
ASCII line feed character
61180008L1-35A
B-1
Appendix B, Response Messages Data Dictionary
Total Access 1500 System TL1 Reference Guide
Table B-1. Total Access 1500 TL1 Response Messages Data Dictionary (Continued)
Parameter
Description
LOCN
The Location parameter indicates the location for which an alarm condition is being
reported. Valid values for the LOCN parameter are NEND and FEND.
MONLEV
The Monitor Level parameter indicates the discriminating level for the requested
monitored parameter. Supported values include:
0-UP: show zero values.
1-UP: suppress zero values.
MONTYPE
This parameter provides the type of monitored parameter for which a value is being
retrieved. Examples are ESL, SESL, and UASP.
MONVAL
This parameter provides the measured value for the MONTYPE parameter.
NTFCNCDE
The Notification Code parameter provides a two-character code associated with a single
alarm condition. The following Notification Codes apply to the Total Access 1500
system:
CR: Critical
MJ: Major
MN: Minor
SC: Standing Condition
OCRDAT
This parameter indicates the Occurrence Date for a triggering event. The format for the
OCRDAT parameter is MM-DD.
MM indicates month and ranges from 1 to 12; DD indicates day and ranges from 1 to 31.
OCRTM
This parameter indicates the Occurrence time of day for a triggering event. The format
for the OCRTM parameter is HH-MM-SS.
HH indicates hour and ranges from 1 to 23; MM indicates minutes and ranges from 0 to
59; SS indicates seconds and ranges from 0 to 59.
REPTINVL
When part of a Response message, the Report Interval parameter indicates how often a
report was scheduled to be generated. The format for this parameter is in the form of
either nn-MIN, hh-HR, or nn-DAY.
The nn-MIN parameter indicates minutes (values, 1 to 1440).
The hh-HR parameter indicates hours (values, 1 to 24).
The nn-DAY parameter indicates day (values, 1 to 31).
REPTSTATM
The Report Start Time parameter specifies the time of day for the next PM report. The
format for the REPTSTATM parameter is HH-MM.
HH indicates hour of day (values, 0 to 23).
MM indicates minute of hour ( values, 0 to 59).
<rspblk>
The Response Block contains the information that an NE entity sends to the OS/user.
Information in the Response Block depends on the NE entity sending the data to the OS/
user and also depends on the input command parameters sent to the NE by the OS/user.
SID
The Source Identifier (SID) identifies the NE generating the Response message. The SID
is usually the shelf CLLI code or the value assigned to a shelf by TIRKS.
B-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Appendix B, Response Messages Data Dictionary
Table B-1. Total Access 1500 TL1 Response Messages Data Dictionary (Continued)
Parameter
Description
SRVEFF
This parameter indicates the effect on the service caused by an alarm condition.
Valid values for SRVEFF are:
SA - Service-affecting condition, immediate action required
NSA - Nonservice-affecting condition, action required.
Refer to Appendix D, Alarms and Alarm Condition Codes, for Service Effecting data.
<SW Rev.>
This parameter indicates the software release for an NE.
TAP
The Test Access Path parameter identifies messages between a TSC and an NE during an
MTA test. The Total Access 1500 system supports a range from 1 to 48.
TMOFST
The Time Offset parameter indicates the time offset from the end of the last complete
accumulation time period to the beginning of the accumulation period specified in the
TMPER parameter. The format for TMOFST is DD-HH-MM.
DD indicates days (values, 0 to 31).
HH indicates hours (values, 0 to 23).
MM indicates minutes (values, 0 to 59).
TMPER
The Time Period parameter indicates the accumulation period for Performance
Monitoring (PM) data. The format for TMPER is 15-MIN or 1-DAY.
The NE determines the default value.
TYPE
This parameter consists of a user-specified character string that indicates the system type.
The maximum length is 55 characters. An example of the parameter is TA1500.
TYPEREP
The Type Report parameter identifies the condition type being reported. The condition
type corresponds to the CONDTYPE parameter. Refer to Appendix D, Alarms and Alarm
Condition Codes, for additional information.
VLDTY
The Validity parameter provides historical monitoring information. This parameter
indicates whether the information for the specified monitoring period was accumulated
over the entire monitoring period or some portion of it. Valid values are as follows:
COMPL: Data is accumulated over the entire monitoring period.
PRTL: Data is accumulated over some portion of the monitoring period.
YY-MM-DD
This is the Response message date format where: YY is year, MM is month, and DD is
day. Each component has two digits.
YY ranges from 00 to 99; MM ranges from 01 to 12; DD ranges from 01 to 31.
61180008L1-35A
B-3
Appendix B, Response Messages Data Dictionary
B-4
Total Access 1500 System TL1 Reference Guide
61180008L1-35A
Appendix C
Error Codes
1.
INTRODUCTION
The response message to a TL1 input command contains an error code <errcode> parameter when the
addressed NE cannot complete the action for the input command. Table C-1 provides error codes for the
Total Access 1500 system.
Table C-1. Total Access 1500 System Error Codes
Error Code
Category
Description
EANS
Equipment
This error code indicates access is not supported.
ENEQ
Error
This error code indicates the device is not equipped.
ENPM
Error
This error code indicates performance monitoring is not supported.
ICNV
Input
This error code indicates the command is not valid.
IDRG
Input
This error code indicates the date range is not valid.
IIAC
Input
This error code indicates an invalid access identifier.
IIDT
Input
This error code indicates an invalid data parameter.
IIPG
Input
This error code indicates invalid parameter grouping.
INAC
Input
This error code indicates an invalid test access point.
IPNV
Input
This error code indicates the parameter is not valid.
PIUI
Privilege
This error code indicates the input user is not valid.
PLNA
Privilege
This error code indicates the login is not active or insufficient privileges.
RCBY
Resource
This error code indicates a circuit busy condition (access point is in use).
SADC
Status
This error code indicates the device is already disconnected.
SNVS
Status
This error code indicates the device is not in a valid state.
SRAC
Status
This error code indicates the requested access configuration is not valid.
SROF
Status
This error code indicates the requested operation failed.
SSRE
Status
This error code indicates the system resource is not available.
61180008L1-35A
C-1
Appendix C, Error Codes
C-2
Total Access 1500 System TL1 Reference Guide
61180008L1-35A
Appendix D
Alarms and Alarm Condition Codes
1.
INTRODUCTION
This appendix provides alarm information for the System Controller Unit (SCU), and the Line Interface
Unit (LIU) cards that apply to the Total Access 1500 system. This appendix also provides information
about alarm condition codes that apply to the Total Access 1500 system.
SCU Alarms
Table D-1 provides alarm information for the SCU. For the Service Effecting column, NSA indicates
Non Service Affecting, and SA indicates Service Affecting. MJ indicates Major. MN indicates Minor.
Table D-1. Total Access 1500 SCU Alarm Data
Condition Code
<CONDTYPE>
Alarm
Level
Service Affecting
<SRVEFF>
Location
<LOCN)
Description
Local Shelf Alarms
AUX1
MN
NSA
NEND
This Environmental (ENV) alarm condition indicates the External Input #1 alarm is active. AID is
1-1-30-1.
AUX2
MN
NSA
NEND
This ENV alarm condition indicates the External
Input #2 alarm is active.
AID is 1-1-30-2.
AUX3
MN
NSA
NEND
This ENV alarm condition indicates the External
Input #3 alarm is active.
AID is 1-1-30-3.
AUX4
MN
NSA
NEND
This ENV alarm condition indicates the External
Input #4 alarm is active.
AID is 1-1-30-4.
CONTEQPT
MN
NSA
NEND
This Equipment (EQPT) alarm condition indicates
the SCU has sensed the specified LIU is in a fail/
protect status.
AID is 1-1-25 for LIU-A or 1-1-26 for LIU-B.
61180008L1-35A
D-1
Appendix D, Alarms and Alarm Condition Codes
Total Access 1500 System TL1 Reference Guide
Table D-1. Total Access 1500 SCU Alarm Data (Continued)
Condition Code
<CONDTYPE>
Alarm
Level
Service Affecting
<SRVEFF>
Location
<LOCN)
Description
CONTEQPT
MJ
SA
NEND
This EQPT alarm condition indicates the SCU has
sensed the specified LIU is in a fail/unprotect status.
AID is 1-1-25 for LIU-A or 1-1-26 for LIU-B.
CTNEQPT
MN
NSA
NEND
This EQPT alarm condition indicates a card has
been removed from the chassis.
CTNEQPT
MJ
SA
NEND
This EQPT alarm condition indicates a card that
affects service has been removed from the chassis.
This can also be an alarm condition that indicates
alarm escalation.
EQPT
Alert
NSA
NEND
This alarm condition indicates the SCU has sensed
the LIU S/W Rev alarm. (LIU S/W Rev alarm)
PWR
MN
NSA
This EQPT alarm condition indicates the local
shelf PSU-A has failed.
AID is 1-1-28.
PWR
MN
NSA
FEND
This EQPT alarm condition indicates the local
shelf PSU-B has failed.
AID is 1-1-29.
PWRPRI
MN
NSA
This ENV alarm condition indicates Bus A Power
Failure alarm (primary power) is active.
AID is 1-1-30-5.
PWRSEC
MN
NSA
This ENV alarm condition indicates Bus B Power
Failure alarm (secondary power) is active.
AID is 1-1-30-6
REM
MN
NSA
FEND
This alarm condition indicates the SCU has sensed
the FEND Remote alarm
RT
MN
NSA
NEND
This alarm condition indicates the specified local
power supply ring generator (RGU-A or RGU-B)
has failed and is in protected status.
RT
MJ
SA
NEND
This alarm condition indicates the specified local
power supply ring generator (RGU-A or RGU-B)
has failed and is in unprotected status.
WKSWPR
Alert
NSA
NEND
This alarm condition indicates the SCU has sensed
an LIU switch to protection state.
D-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Appendix D, Alarms and Alarm Condition Codes
Table D-1. Total Access 1500 SCU Alarm Data (Continued)
Condition Code
<CONDTYPE>
Alarm
Level
Service Affecting
<SRVEFF>
Location
<LOCN)
Description
Remote Shelf Alarms
AUX1
MN
NSA
FEND
This ENV alarm condition indicates the SCU has
sensed the remote shelf AUX1 alarm.
AID is 1-1-31-1.
AUX2
MN
NSA
FEND
This ENV alarm condition indicates the SCU has
sensed the remote shelf AUX2 alarm.
AID is 1-1-31-2.
AUX3
MN
NSA
FEND
This ENV alarm condition indicates the SCU has
sensed the remote shelf AUX3 alarm.
AID is 1-1-31-3.
AUX4
MN
NSA
FEND
This ENV alarm condition indicates the SCU has
sensed the remote shelf AUX4 alarm.
AID is 1-1-31-4.
CTNEQPT
MN
NSA
FEND
This EQPT alarm condition indicates the remote
shelf SCU alarm is active.
AID is 1-1-34.
CTNEQPT
MN
NSA
FEND
This EQPT alarm condition indicates the remote
shelf LIU-A alarm is active.
AID is 1-1-35.
CTNEQPT
MN
NSA
FEND
This EQPT alarm condition indicates the remote
shelf LIU-B alarm is active.
AID is 1-1-36.
PWR
MN
NSA
FEND
This EQPT alarm condition indicates the remote
shelf PSU-A alarm is active.
AID is 1-1-32.
PWR
MN
NSA
FEND
This EQPT alarm condition indicates the remote
shelf PSU-B alarm is active.
AID is 1-1-33.
PWRPRI
MN
NSA
FEND
This ENV alarm condition indicates the remote
shelf primary power feed alarm is active (Bus A
Power Failure alarm).
AID is 1-1-31-5.
61180008L1-35A
D-3
Appendix D, Alarms and Alarm Condition Codes
Total Access 1500 System TL1 Reference Guide
Table D-1. Total Access 1500 SCU Alarm Data (Continued)
Condition Code
<CONDTYPE>
Alarm
Level
Service Affecting
<SRVEFF>
Location
<LOCN)
Description
PWRSEC
MN
NSA
FEND
This ENV alarm condition indicates the remote
shelf secondary power feed alarm is active (Bus B
Power Failure alarm).
AID is 1-1-31-6.
RT
MN
NSA
FEND
This EQPT alarm condition indicates the remote
shelf power supply ring generator (RGU-A) has
failed and is in protected status.
AID is 1-1-32.
RT
MN
NSA
FEND
This EQPT alarm condition indicates the remote
shelf power supply ring generator (RGU-B) has
failed and is in protected status.
AID is 1-1-33.
RT
MJ
SA
FEND
This EQPT alarm condition indicates both remote
shelf power supply ring generators (RGU-A and
RGU-B) have failed.
AID is 1-1-32.
D-4
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Appendix D, Alarms and Alarm Condition Codes
LIU Alarms
Table D-2 provides the alarms for the LIU card. Table entries with the T-x format, (for example, T-CVL),
provide Performance Monitoring (PM) data for both quarterly and daily threshold violations that are sent
from the NE to the OS/user. The threshold alarms are Transient Conditions (TC). The alarms in this table
are for transmission type T1. The applicable TL1 commands include: RTRV-ALM-T1 and RTRV-ALMALL. MJ indicates Major. MN indicates Minor.
Table D-2. Total Access 1500 LIU Alarm Data
Condition Code
<CONDTYPE>
Alarm
Level
Service Affecting
<SRVEFF>
Location
<LOCN>
Description
T-CVL
Alert
NSA
NEND
This alarm indicates a coding violation threshold
has been exceeded at the near end line.
T-ESL
Alert
NSA
NEND
This alarm indicates an errored second threshold
has been exceeded at the near end line.
T-SESL
Alert
NSA
NEND
This alarm indicates a severely errored second
threshold has been exceeded at the near end line.
T-CVP
Alert
NSA
NEND
This alarm indicates a coding violation threshold
has been exceeded at the near end path.
T-ESP
Alert
NSA
NEND
This alarm indicates an errored second threshold
has been exceeded at the near end path.
T-ESBP
Alert
NSA
NEND
This alarm indicates a type B errored second
threshold has been exceeded at the near end path.
T-SESP
Alert
NSA
NEND
This alarm indicates a severe errored second
threshold has been exceeded at the near end path.
T-SASP
Alert
NSA
NEND
This alarm indicates a severely errored framing/
alarm indication signal second threshold has been
exceeded at the near end path.
T-UASP
Alert
NSA
NEND
This alarm indicates an unavailable second
threshold has been exceeded at the near end path.
T-CSS
Alert
NSA
NEND
This alarm indicates a control slip seconds
threshold has been exceeded at the near end.
T-ES-LFE
Alert
NSA
FEND
This alarm indicates an errored second threshold
has been exceeded at the far end line.
T-CSS-PFE
Alert
NSA
FEND
This alarm indicates a control slip seconds
threshold has been exceeded at the far end path.
61180008L1-35A
D-5
Appendix D, Alarms and Alarm Condition Codes
Total Access 1500 System TL1 Reference Guide
Table D-2. Total Access 1500 LIU Alarm Data (Continued)
Condition Code
<CONDTYPE>
Alarm
Level
Service Affecting
<SRVEFF>
Location
<LOCN>
Description
T-CV-PFE
Alert
NSA
FEND
This alarm indicates a coding violation threshold
has been exceeded at the far end path.
T-ES-PFE
Alert
NSA
FEND
This alarm indicates an errored second threshold
has been exceeded at the far end path.
T-ESB-PFE
Alert
NSA
FEND
This alarm indicates a type B errored second
threshold has been exceeded at the far end path.
T-SES-PFE
Alert
NSA
FEND
This alarm indicates a severely errored second
threshold has been exceeded at the far end path.
T-SEFS-PFE
Alert
NSA
FEND
This alarm indicates a severely errored framing second threshold has been exceeded at the far end path.
T-UAS-PFE
Alert
NSA
FEND
This alarm indicates an unavailable second
threshold has been exceeded at the far end path.
AIS
MJ
SA
NEND
This alarm indicates a service-affecting Alarm
Indication Signal (AIS) condition is detected at the
near end.
AIS
MN
NSA
NEND
This alarm indicates a non-service affecting AIS
condition is detected at the near end.
BPV
MJ
SA
NEND
This alarm indicates a service-affecting BiPolar
Violation (BPV) condition is detected at the near
end
BPV
MN
NSA
NEND
This alarm indicates a non-service affecting BPV
condition is detected at the near end.
INC
MJ
SA
NEND
This alarm indicates a service-affecting data link
failure at the near end. The Incoming Failure
Condition (INC) SA alarm is active.
INC
MN
NSA
NEND
This alarm indicates a non-service affecting data
link failure at the near end. The INC NSA warning
is active.
LOF
MJ
SA
NEND
This alarm indicates a service-affecting Loss of
Frame (LOF) condition at the near end. The LOF
SA alarm is active.
LOF
MN
NSA
NEND
This alarm indicates a non-service affecting LOF
condition at the near end. The LOF NSA alarm is
active.
D-6
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Appendix D, Alarms and Alarm Condition Codes
Table D-2. Total Access 1500 LIU Alarm Data (Continued)
Condition Code
<CONDTYPE>
Alarm
Level
Service Affecting
<SRVEFF>
Location
<LOCN>
Description
LOS
MJ
SA
NEND
This alarm indicates a service-affecting Loss of
Signal (LOS) condition at the near end. The LOS
SA alarm is active.
LOS
MN
NSA
NEND
This alarm indicates a non-service affecting LOS
condition at the near end. The LOS NSA alarm is
active.
LPBKDS1FEAC
MJ
SA
FEND
This alarm indicates a far shelf, DS1 FEAC loopback trouble condition at the far end.
LPBKLINE
MJ
SA
NEND
This alarm indicates a service-affecting line loopback trouble condition at the near end.
LPBKLINE
MN
NSA
NEND
This alarm indicates a non-service affecting line
loopback trouble condition a the near end.
LPBKLOCAL
MJ
SA
NEND
This alarm indicates a service-affecting local loopback trouble condition at the near end.
LPBKLOCAL
MN
NSA
NEND
This alarm indicates a non-service affecting local
loopback trouble condition at the near end.
LPBKPAYLOAD
MJ
SA
NEND
This alarm indicates a service-affecting payload
loopback trouble condition at the near end.
LPBKPAYLOAD
MN
NSA
This alarm indicates a non-service affecting
payload loopback trouble condition at the near end.
NEND
RAI
MJ
SA
FEND
This alarm indicates a service-affecting Remote
Alarm Indication (RAI) condition at the far end.
The RAI SA alarm is active.
RAI
MN
NSA
FEND
This alarm indicates a non-service affecting RAI
condition at the far end. The RAI NSA alarm is
active.
RFI
MJ
SA
FEND
This alarm indicates a service-affecting Remote
Failure Indication (RFI) condition at the far end.
The Far Shelf RFI SA alarm is active.
RFI
MN
NSA
FEND
This alarm indicates a non-service affecting RFI
condition is detected at the far end. The Far Shelf
RFI NSA alarm is active.
SYNCPRI
MN
NSA
NEND
This alarm indicates a non-service affecting
primary timing source condition is detected.
61180008L1-35A
D-7
Appendix D, Alarms and Alarm Condition Codes
Total Access 1500 System TL1 Reference Guide
Table D-2. Total Access 1500 LIU Alarm Data (Continued)
Condition Code
<CONDTYPE>
Alarm
Level
Service Affecting
<SRVEFF>
Location
<LOCN>
Description
SYNCPRI
MJ
SA
NEND
This alarm indicates a service-affecting timing
source condition is detected (OOS SA condition).
SYNCSEC
MN
NSA
NEND
This alarm indicates a non-service affecting
secondary timing source condition is detected.
WKSWPR
Alert
NSA
NEND
This alarm indicates a T1 Switch-to-Protect
condition is active.
D-8
61180008L1-35A
Appendix E
Autonomous Messages
1.
INTRODUCTION
This appendix provides information about autonomous messages. Autonomous messages are generated
automatically by alarm conditions or events that occur at Network Elements (NEs). The ALW-MSG TL1
commands allow the sending of autonomous messages to the OS/user. The INH-MSG TL1 commands
inhibit or prevent the sending of autonomous messages to the OS/user.
2.
SYNTAX
An autonomous message for the Total Access 1500 system has the following format:
<cr> <lf> <lf>
^^^<source identifier>^<date>^<time> <cr> <lf>
<almcde>^<atag>^<verb>[^<modifier> [^<modifier>]] <cr> <lf>
^^^"<aid>:<message parameter>" <cr> <lf>
Table E-1 provides parameter (field) descriptions for autonomous messages.
Table E-1. Autonomous Messages Parameter Descriptions
Parameter
Description
<cr>
Carriage return
<lf>
Line feed
Caret (^)
Represents one space character
<source identifier>
The Shelf CLLI code or shelf number assigned by TIRKS
<date>
Date in the form YY-MM-DD
<time>
Time in the form HH-MM-SS
<almcde>
Alarm code. The alarm code indicates the severity of the autonomous
message. Valid values for <almcde> in decreasing order of severity are
as follows:
*C Critical alarm
** Major alarm
*^ Minor alarm
A^ Non-alarm message
61180008L1-35A
E-1
Appendix E, Autonomous Messages
Total Access 1500 System TL1 Reference Guide
Table E-1. Autonomous Messages Parameter Descriptions (Continued)
Parameter
Description
<atag>
Autonomously Generated Correlation Tag (ATAG). The ATAG is a
decimal number assigned by the NE. The ATAG must be sequential
and must be included in all autonomous messages. The ATAG allows
an OS/user to determine if the OS has failed to receive any autonomous
outputs by checking for omissions in the sequence of messages
received.
<verb>[^<modifier>[^<modifier>]]
Identifies the nature of the autonomous output and allows for quick
identification of the semantics of the information in the text block. It
consists of up to three valid TL1 identifiers separated by the space
character (^). The first identifier (<verb>) is the autonomous message
verb and is a required entry. In most cases, the verb in an autonomous
message will be REPT (Report). The autonomous message verb can
have up to two optional modifiers. The valid forms are:
<verb>
<verb>^<modifier>
<verb>^<modifier>^<modifier>
The first modifier following the verb modifies the verb. The second
modifier specifies the object generating the message. Certain modifiers
(for example, EQPT) mean that the <AID> parameter, if it exists, is
addressing a particular type of entity in the NE.
<message block>
Detailed data related to the specific alarm or report.
E-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
3.
Appendix E, Autonomous Messages
ALARMS
Autonomous alarms are sent only when users are currently logged on the system, and only after the users
have entered an “ALW-MSG-xx” command to enable sending the alarms. The xx field can be “EQPT,
“T1,” or “ALL.” Another field in the command, the <parameter block> field, can select all alarm
categories or a specific alarm such as MAJOR. The companion command, “INH-MSG-xx” inhibits all or
selected types of messages. The xx field can be “EQPT,” “T1,” or “ALL.” The effects are cumulative such
that a user could allow all alarms, and then inhibit only the MINOR alarms.
DS0 level alarms are not generated, only T1 and higher. Once a user logs off the system, the autonomous
alarms cease.
There is no specified or provisionable TL1 session-timeout period. If a user is logged into a TL1 account,
the account remains active until the user explicitly logs out or the session is terminated (for example, TL1
over TCP/IP session closed, or X.25 connection lost).
Events
Events are a variety of alarms, which have a severity of ALERT. The format of the detailed data is slightly
different than that of the alarms in that the condition code and status fields are reversed.
4.
PERFORMANCE MONITORING REPORTS
Autonomous Performance Monitoring (PM) reports may be generated as a result of a SCHED-PMREPTxx command.
5.
CONDITION CODES
Condition codes are assigned to identify specific reasons for the alarm or event. Refer to Appendix D,
Alarms and Alarm Condition Codes, for information about the condition codes generated by the circuit
cards in a Total Access 1500 shelf.
6.
AUTONOMOUS MESSAGE EXAMPLES
The following autonomous message examples apply to the Total Access 1500 system.
HTVLALEXD01 11-01-23 02:44:42
A 17 REPT EVT T1
"1-1-25:WKSWPR,SC,01-23,02-44-42,NEND,,,,"
;
HTVLALEXD01 11-01-23 02:44:43
* 18 REPT ALM T1
"1-1-25:MN,LOS,NSA,01-23,02-44-43,NEND,,,,"
;
61180008L1-35A
E-3
Appendix E, Autonomous Messages
Total Access 1500 System TL1 Reference Guide
HTVLALEXD01 11-01-23 20:41:34
** 203 REPT ALM EQPT
"1-1-25:MJ,CTNEQPT,SA,01-23,20-41-34,NEND,,,,"
;
E-4
61180008L1-35A
Appendix F
Quad-Port Line Cards
1.
INTRODUCTION
This appendix provides TL1 information about the following Quad line cards for the Total Access 1500
system:
•
•
•
2.
Quad C-POTS, (P/N 1180407L1)
Quad R-POTS, (P/N 1180408L1)
Total Access 750 Quad FXO (P/N 1175407L1/L2
AID FORMAT
The following AID format applies to the Quad line cards: shelf-digroup-slot-port.
Refer to Section 3, ADTRAN AID Formats, for additional information.
Port Numbers
The port number, which is the fourth segment of the AID parameter, indicates the specific interface point
in a Quad line card circuit. Port numbers for Quad cards are 1 through 4.
3.
ALARMS
The Quad line cards that apply to the Total Access 1500 system do not generate TL1 alarm information.
61180008L1-35A
F-1
Appendix F, Quad-Port Line Cards
F-2
Total Access 1500 System TL1 Reference Guide
61180008L1-35A
Appendix G
Dual-Port Line Cards
1.
INTRODUCTION
This appendix provides information about the following Dual-Port line cards that apply to the Total Access
1500 system:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2.
Dual DS0 DP (P/N 1180203L1/-L4)
Dual OCU DP (P/N 1180205L1-L4)
Dual FXO (P/N 1180207L1/L2)
Dual FXS (P/N 1180208L1/L2)
Dual TO (P/N 1180212L1/L2)
Dual FXS/GT (P/N 1180214L1/L2)
Dual FXO/GT (P/N 1180215L1/L2)
Dual DX (P/N 1180216L1/L2
Dual 4FXO (P/N 1180217L1/L2)
Dual 4FXS (P/N 1180218L1/L2)
Dual EBS-C (P/N 1180430L1)
Dual EBS-R (P/N 1180431L1)
Dual Coin COT (P/N 1180432L1)
Dual Nx64 (P/N 1180025)
AID FORMAT
The following AID format applies to the Dual line cards: shelf-digroup-slot-port.
Refer to Section 3, ADTRAN AID Formats, for additional information.
3.
PORT NUMBERS
Port number for Dual cards are 1 and 2.
4.
ALARMS
The Dual line cards that apply to the Total Access 1500 system do not generate TL1 alarm information.
61180008L1-35A
G-1
Appendix G, Dual-Port Line Cards
G-2
Total Access 1500 System TL1 Reference Guide
61180008L1-35A
Appendix H
Single-Port Line Cards
1.
INTRODUCTION
This appendix provides information about the following Single-Port line cards for the Total Access 1500
system:
•
•
•
•
•
•
•
•
2.
E&M (P/N 1180212L1/L2)
FXS (P/N 1180403L1)
FXO (P/N 1180404L1)
MCU (P/N 1180434)
UBR1TE (P/N 1180020L1/L2)
DS0 DP (P/N 1180003L1)
OCU DP (P/N 1180005L1)
FXO/GT (P/N 1180115L1/L2)
AID FORMAT
The following AID format applies to the Single line cards: shelf-digroup-slot-port.
Refer to Section 3, ADTRAN AID Formats, for additional information.
3.
PORT NUMBERS
The port number for the Single line cards is always 1.
4.
ALARMS
The Single line cards that apply to the Total Access 1500 system do not generate TL1 alarm information.
61180008L1-35A
H-1
Appendix H, Single-Port Line Cards
H-2
Total Access 1500 System TL1 Reference Guide
61180008L1-35A
Appendix I
List of Abbreviations
AID
Access Identifier
AIDTYPE
Access Identifier Type
AIS
Alarm Indication Signal
ATAG
Autonomously Generated Correlation Tag
CLLI
Common Language Location Identifier
CO
Central Office
CONDTYPE
Condition Type
CTAG
Correlation Tag
DIR
Direction
DP
Data Port
DPO
Dial Pulse Origination
DPT
Dial Pulse Termination
E&M
Ear and Mouth (also known as rEceive and transMit)
FXO
Foreign Exchange Office
FXS
Foreign Exchange Service
GT
Gain Transfer
INC
Incoming Failure Condition
INE
Intelligent Network Element
LIU
Line Interface Unit
LOCN
Location
LOF
Loss of Frame
LOS
Loss of Signal
MONDAT
Monitor Date
MONLEV
Monitor Level
MONTM
Monitor Time
MONTYPE
Monitor Type
MONVAL
Monitor Value
61180008L1-35A
I-1
Appendix I, List of Abbreviations
Total Access 1500 System TL1 Reference Guide
MTA
Metallic Test Access
NE
Network Element
NSA
Non-Service Affecting
NTFCNCDE
Notification Code
NUMINVL
Number Interval
NUMREPT
Number of Reports
OCRDAT
Occurrence Date
OCRTM
Occurrence Time
OCU
Office Channel Unit
OS
Operations System
OSS
Operations Support System
PM
Performance Monitoring
POTS
Plain Ordinary Telephone Service or Plain Old Telephone Service
PSU
Power Supply Unit
RAI
Remote Alarm Indicator
REPTDAT
Report Date
REPTINVL
Report Interval
REPTSTATM Report Starting Time
REPTTM
Report Time
RFI
Remote Failure Indication
rspblk
Response Block
RTU
Remote Test Unit
SA
Service Affecting
SCU
System Controller Unit
SID
Source Identifier
SRVEFF
Service Effecting
TAP
Test Access Path
TC
Transient Condition
TCP/IP
Transmission Control Protocol/Internet Protocol
TID
Target Identifier
TL1
Transaction Language 1
TMOFST
Time Offset
TMPER
Time Period
I-2
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
TO
Transmit Only
TSC
Test System Controller
TYPEREP
Type Report
U-BR1TE
U Interface- Basic Rate 1(2B+D) Termination Equipment
UID
User ID
VLDTY
Validity
61180008L1-35A
Appendix I, List of Abbreviations
I-3
Appendix I, List of Abbreviations
I-4
Total Access 1500 System TL1 Reference Guide
61180008L1-35A
Appendix J
Total Access 1500 TL1 Quick Reference Table
1.
INTRODUCTION
Table J-1 provides quick reference data for the TL1 commands and response messages that apply to the
Total Access 1500 system.
Refer to Appendix A and Appendix B in this manual for information about the Input parameters and the
Response parameters.
Refer to Appendix F, Appendix G, and Appendix H in this manual for information about the Quad-Port,
Dual-Port, and Single-Port line cards respectively.
2.
NOTATIONS
[ ], indicates an optional TL1 input parameter.
< >, indicates a TL1 input parameter.
{|}, indicates a chose between the command modifiers separated by the pipe (|) symbol.
3.
AID STRUCTURE
For the SCU and LIU cards: shelf-digroup-slot
For the Quad-Port, Dual-Port, and Single-Port line cards: shelf-digroup-slot-port
4.
AID VALUES
Shelf: set at 1 in current software release, even if multiple shelves are chained with the RS-485.
Digroup: 1-5 (For T1 alarms, the digroup number identifies the T1. T1 number 5 is the protect line in
SLC96 mode.)
Slot: 0 for SCU; 25 and 26 for LIU (LIU-A is slot 25 and LIU-B is slot 26); 1-24 for line cards; 30 for
environmental alarms.
31 for environmental alarms (remote shelf); 32 for PSU-A (remote shelf); 33 for PSU-B (remote shelf) 34
for SCU (remote shelf);
35 for LIU-A (remote shelf); 36 for LIU-B (remote shelf)
Port: 1-4 for Quad-port line cards; 1 and 2 for Dual-port line cards; 1 for Single-port line cards
5.
ALARMS
Currently, the Total Access 1500 line cards and the PSU do not generate alarms.
61180008L1-35A
J-1
Appendix J, Total Access 1500 TL1 Quick Reference Table
Total Access 1500 System TL1 Reference Guide
The SCU generates alarms for the PSU.
Slot 28 or 29 in the AID parameter of an alarm response message from the SCU indicates a PSU has failed.
For example, 1-1-28 in an AID parameter indicates PSU-A has failed, and 1-1-29 in an AID parameter
indicates PSU-B has failed.
Slot 30 in the AID parameter of an alarm response message indicates an environmental alarm.
Table J-1. Total Access 1500 TL1 Quick Reference
Command
ACT-USER
ALW-MSG
CANC-USER
CANC-USERSECU
CHG-SPLIT
CHG-SPLIT-LILO
CONN-LPACCMET
J-2
Type
Description
Description
Activates TL1 session
Input Format
ACT-USER:[<tid>]:<user>:[<ctag>]::<password>;
Response Message
System responds with COMPLD message.
Description
Allows autonomous alarm data from an NE
Input Format
ALW-MSG-{T1|EQPT|ALL}:[<tid>]:<null>:[<ctag>]::[<ntfcncde>];
Response Message
System responds with COMPLD message. System generates autonomous messages.
Description
Terminates TL1 session
Input Format
CANC-USER:[<tid>]:[<user>]:[<ctag>];
Response Message
System responds with COMPLD message.
Description
Terminates unauthorized TL1 session
Input Format
CANC-USER-SECU:[<tid>]:<user>:[<ctag>];
Response Message
System responds with COMPLD message.
Description
Provide connections for test circuit.
Input Format
CHG-SPLIT:[<tid>]:<tap>:[<ctag>];
Response Message
System responds with COMPLD message.
Description
Provide connections and splits test circuit (only applies to non-simultaneous split access)
Input Format
CHG-SPLIT-LILO:[<tid>]:<tap>]:[<ctag>]::<dir>;
Response Message
System responds with COMPLD message.
Description
Controls TAP, TAP designation, and TAP loop around.
Input Format
CONN-LPACC-MET:[<tid>]:<aid>:[<ctag>]::<tap>:<cnfgrn>;
AID Structure
Shelf-digroup-slot for SCU and LIU cards; shelf-digroup-slot-port
for Quad, Dual, and Single-Port cards
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Appendix J, Total Access 1500 TL1 Quick Reference Table
Table J-1. Total Access 1500 TL1 Quick Reference (Continued)
Command
CONN-MON
CONN-TACCMET
DISC-TACC
INH-MSG
OPR-LPBK-TST
REPT-STAT
RLS-LPBK-TST
RST-TAP-MET
61180008L1-35A
Type
Description
Response Message
System responds with COMPLD message.
Description
Establishes a monitor state for test circuit
Input Format
CONN-MON:[<tid>]:<tap>:[<ctag>];
Response Message
System responds with COMPLD message.
Description
Provides monitor connection for transmission pairs of a circuit and
completes test access
Input Format
CONN-TACC-MET:[<tid>]:<tap>:[<ctag>];
Response Message
System responds with COMPLD message.
Description
Disconnects TAP connection and restores circuit to through state
Input Format
DISC-TACC:[<tid>]:<tap>:[<ctag>];
Response Message
System responds with COMPLD message.
Description
Inhibits autonomous alarm data from an NE
Input Format
INH-MSG-{T1|EQPT|ALL}:[<tid>]:<null>:[<ctag>]::[<ntfcncde>];
Response Message
System responds with COMPLD message.
Description
Operates a loopback on a specified TAP
Input Format
OPR-LPBK-TST:[<tid>]:<aid>:[<ctag>];
AID Structure
Shelf-digroup-slot for SCU and LIU cards; shelf-digroup-slot-port
for Quad, Dual, and Single-Port cards
Response Message
System responds with a COMPLD message.
Description
Checks data line between TSC/RTU and NE
Input Format
REPT-STAT:[<tid>]:<null>:[<ctag>];
Response Message
System responds with an OK Acknowledgment message.
Description
Releases loopback on a specified TAP
Input Format
RLS-LPBK-TST:[<tid>]:<aid>:[<ctag>];
AID Structure
Shelf-digroup-slot for SCU and LIU cards; shelf-digroup-slot-port
for Quad, Dual, and Single-Port cards
Response Message
System responds with COMPLD message.
Description
Releases all existing test access connections in the NE
Input Format
RST-TAP-MET:[<tid>]:[ALL]:[<ctag>];
Response Message
System responds with COMPLD message.
J-3
Appendix J, Total Access 1500 TL1 Quick Reference Table
Total Access 1500 System TL1 Reference Guide
Table J-1. Total Access 1500 TL1 Quick Reference (Continued)
Command
RTRV-ALM
Type
Description
Description
Retrieves alarms from an NE
Input Format
RTRV-ALM{T1|EQPT|ALL|ENV}:[<tid>]:[<aid>]:[<ctag>]::[<ntfcncde>];
AID Structure
Shelf-digroup-slot for SCU and LIU cards
Response Message
System responds with COMPLD message. Format for alarm
conditions:
^^"[<aid>][,<aidtype>]:<ntfcncde>,<condtype>,<srveff>,[<ocrdat>],[<ocrtm>],[<locn
>],,[<tmper>]"
RTRV-COND
RTRV-HDR
RTRV-PM-T1
RTRV-SYS
RTRV-VERSION
J-4
Description
Retrieves condition or state data for an NE
Input Format
RTRV-COND-{T1|EQPT|ALL}:[<tid>]:[<aid>]:[<ctag>];
AID Structure
Shelf-digroup-slot for SCU and LIU cards; shelf-digroup-slot-port
for Quad, Dual, and Single-Port line cards
Response Message
System responds with COMPLD message. Format for conditions and
state:
^^^"<aid>[,<aidtype>]:[<ntfcncde>],<typerep>,[<srveff>],[<ocrdat>],[<ocrtm>],[<locn>],,[<tmper>]"
Description
Retrieves data that an NE has about itself such as Source Identifier,
date, time, and software release.
Input Format
RTRV-HDR:[<tid>]:<null>:[<ctag>];
Response Message
System responds with COMPLD message, header data, and software
release for the NE.
Description
Retrieves T1 PM data from an NE
Input Format
RTRV-PM-T1:[<tid>]:<aid>:[<ctag>::,[<monlev>],[<locn>],,[<tmper>],[<mondat>],[<montm>];
AID Structure
Shelf-digroup-slot for SCU and LIU cards
Response Message
System responds with COMPLD. Format for T1 PM data:
^^^"<aid>:<montype>,<monval>,[<vldty>],[<locn>],,[<tmper>],[<mondat>][,<montm>]"
Description
Retrieves Total Access system type from the SCU
Input Format
RTRV-SYS:[<tid>]::[<ctag>];
Response Message
System responds with COMPLD and system type data.
Description
Retrieves current software release from the SCU
Input Format
RTRV-VERSION:[<tid>]::[<ctag>];
Response Message
System responds with COMPLD and software release data.
61180008L1-35A
Total Access 1500 System TL1 Reference Guide
Appendix J, Total Access 1500 TL1 Quick Reference Table
Table J-1. Total Access 1500 TL1 Quick Reference (Continued)
Command
SCHEDPMREPT-T1
61180008L1-35A
Type
Description
Description
Schedules T1 PM reports for an NE
Input Format
SCHED-PMREPT-T1:[<tid>]:<aid>:[<ctag>]::[<reptinvl>],[<reptstatm>],[<numrept>],,[<monlev>],[<locn>],,[<tmper>],[<tmofst>];
AID Structure
Shelf-digroup-slot for SCU and LIU cards
Response Message
System responds with COMPLD message. Format depends on the
input parameters used with the input command.
J-5
Appendix J, Total Access 1500 TL1 Quick Reference Table
Total Access 1500 System TL1 Reference Guide
This page is intentionally blank.
J-6
61180008L1-35A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising