ADTRAN | TM400 | Owner Manual | Adtran TM400 Owner manual

Adtran TM400 Owner manual
Section 61245065L1-5
Issue 1, November 1998
CLEI #NCTEAABCAA
PRACTICES
TM400
TEST ACCESS CARD
INSTALLATION/MAINTENANCE
Contents
1. GENERAL ............................................................................. 1
2. INSTALLATION .................................................................. 1
3. APPLICATIONS ................................................................... 1
4. FUNCTIONAL DESCRIPTION ........................................... 1
5. TEST SETUPS ....................................................................... 2
6. MAINTENANCE .................................................................. 2
7. WARRANTY AND CUSTOMER SERVICE ...................... 2
TM400
1245065L1
C
U
S
T
Figures
Figure 1. ADTRAN TM400 ...................................................... 1
Figure 2. Loopback Configuration ............................................ 2
Figure 3. Loopthru Configuration ............................................. 2
Figure 4. Short Configuration .................................................... 2
Figure 5. Open Configuration .................................................... 2
C.O.
7
PIN
13
PIN
41
PIN
47
PIN
LOOP 1
LOOP 2
LOOPTHRU
SHORT
OPEN
-VDC SUPPLY
FRAME GRO
LOOP 1
LOOP 2
The basic features of the TM400 are described
below.
• Plugs into ADTRAN T400 housings 1150087L1
and 1150043L1 and L2
• Provides complete testing of wire pairs
• Easy access of pairs
The four-position switch on the card provides a
means for the following:
• Looping back the Central Office (CO) pairs and the
Customer pairs
• Bridging across pairs
• Shorting loop 1 and loop 2
• Opening loop 1 and loop 2
Revision History
The is the first issue of this practice. In subsequent
issues, revisions will be summarized in this
paragraph.
61245065L1-5A
LOO
P2
LOO
HRU
PT
LOO
P1
T1
7
PIN
R1
13
PIN
T
1
4
PIN
R
7
4
PIN
1
7 T
PIN
R1
13
PIN
T
1
4
PIN
R
47
PIN
LOO
P2
LOO
RT
SHO
P1
LOO
P2
T1
7
PIN
R1
13
PIN
T
41
PIN
R
7
4
PIN
T
CUS
IN 5
T1 P 15
IN
R1 P 55
T PIN 49
R PIN
IN 5
T1 P 15
IN
R1 P 55
IN
T P 49
IN
P
R
T1
R1
T
R
5
PIN
15
PIN
55
PIN
49
PIN
LOO
N
OPE
UND
C
O
1. GENERAL
The ADTRAN TM400 (ADTRAN part number
1245065L1) is used for installing and
troubleshooting circuits with T400 mechanics. The
TM400 accesses the four pairs that connect the cardedge socket for metallic and functional testing of the
pairs.
P1
T1
R1
T
R
LOOPBACK
-VDC RETURN
Tables
Table A. Available Access ........................................................ 2
CK
P BA
LOO
1
OOP
L
IN 5
T1 P 15
IN
R1 P 55
IN
T P
9
IN 4
R P
P2
LOO
35
PIN
7
PLY IN 17
,&2
SUP
P
1, 11
-VDC ETURN D PINS
R
N
C
-VD E GROU
M
FRA
Figure 1. ADTRAN TM400
2. INSTALLATION
After unpacking the unit, immediately inspect it for
possible shipping damage. If damage is discovered,
file a claim immediately with the carrier, then
contact ADTRAN Customer Service.
CAUTION
This equipment contains static-sensitive
components. Be sure to use proper electrostatic
discharge procedures before handling or
installing the equipment.
3. APPLICATIONS
The ADTRAN TM400 enables the Telco craft
personnel to test the wire pairs from the repeater
location. Testing of the circuit is accomplished by
removing the repeater, inserting the TM400, and
then choosing the appropriate switch setting
(LOOPBACK, LOOPTHRU, SHORT, or OPEN).
Trademarks: Any brandSection
names and
61245065L1-5,
product names
Issue
included
1
in this document are
trademarks, registered trademarks, or trade names of their respective holders.
1
The TM400 provides Bantam jack access to both the
CO and customer sides of the repeater under
powered conditions. This feature permits access to
the loops for test and monitoring functions.
Testing the CO Pairs
To loopback the circuit, put the switch in the
LOOPBACK position. This loops the circuit back
to the CO and to the customer.
The TM400 also provides access to -48 VDC supply
and return, as well as frame ground reference via
faceplate monitor points.
4. FUNCTIONAL DESCRIPTION
The ADTRAN TM400 may be used in the single
T400 housing (ADTRAN part number 1150087L1)
or the four-slot T400 housing (ADTRAN part
number 1150043L1 or L2). The eight connectors,
labelled LOOP 1, T1, R1, T, and R (C.O.), and T1,
R1, T, and R (CUST), provide direct access to the
wire pair.
The LOOP 1 and LOOP 2 access points labelled T1,
R1, T and R (C.O.) connect to the wire pairs toward
the central office and access points labelled T1, R1,
T and R (CUST) connect to the wire pairs toward
the customer.
The faceplate switch, illustrated in Figure 1, selects
the four functionsfor the four states of LOOPBACK,
LOOPTHRU, SHORT, and OPEN.
5. TEST SETUPS
When using the TM400 to test pairs, consideration
must be given to the configuration setup for the type
of test being performed in order to ensure a valid
test. Available access is detailed in Table A.
Table A. Available Access
Label
Description
PIN 7
PIN 13
PIN 5
PIN 15
PIN 41
PIN 47
PIN 55
PIN 49
PIN 17
PIN 1
PIN 11
PIN 27
PIN 35
LOOP1 Transmit towards CO
LOOP1 Receive towards CO
LOOP1 Transmit towards CUST
LOOP1 Receive towards CUST
LOOP2 Transmit towards CO
LOOP2 Receive towards CO
LOOP2 Transmit towards CUST
LOOP2 Receive towards CUST
-48 VDC Return
Frame Ground
Frame Ground
Frame Ground
-48 VDC Supply
LOOP BACK
C.O.
PIN 7
PIN 13
PIN 41
PIN 47
CUST
T1
R1
T
R
LOOP 1
LOOP 2
T1 PIN 5
R1PIN 15
T PIN 55
R PIN 49
Figure 2. Loopback Configuration
To loopthru the CO pairs to the Customer pairs, put
the switch in the LOOPTHRU position. This
bridges the circuit pairs.
LOOP THRU
PIN 7 T1
PIN 13 R1
PIN 41 T
PIN 47 R
LOOP 1
LOOP 2
T1 PIN 5
R1PIN 15
T PIN 55
R PIN 49
Figure 3. Loopthru Configuration
To short the CO pairs, put the switch in the SHORT
position. This connects transmit to receive on each
loop.
SHORT
PIN 7 T1
PIN 13 R1
PIN 41 T
PIN 47 R
LOOP 1
LOOP 2
T1
R1
T
R
PIN 5
PIN 15
PIN 55
PIN 49
Figure 4. Short Configuration
For test access using the TM400, insert the TM400
into the repeater housing. For the single slot
housing, the print on the TM400 should face away
from the pole or wall. For the four-slot housing, the
print on the TM400 should face the label of the
position you are testing.
2
Section 61245065L1-5, Issue 1
61245065L1-5A
To open the circuit, put the switch in the OPEN
position. This allows for a voltage measurement
across pairs.
OPEN
PIN 7 T1
PIN 13 R1
PIN 41 T
PIN 47 R
LOOP 1
LOOP 2
T1 PIN 5
R1 PIN 15
T PIN 55
R PIN 49
Figure 5. Open Configuration
7. WARRANTY AND CUSTOMER SERVICE
ADTRAN will replace or repair this product within
five years from the date of shipment if it does not
meet its published specifications or fails while in
service.
For detailed warranty, repair, and return information
refer to the ADTRAN Equipment Warranty, Repair,
and Return Policy and Procedure.
Return Material Authorization is required prior to
returning equipment to ADTRAN.
For service, RMA requests, or further information,
contact one of the following numbers:
6. MAINTENANCE
The ADTRAN TM400 requires no routine
maintenance. ADTRAN does not recommend that
repairs be performed in the field. Repair services
may be obtained by returning the defective unit to
ADTRAN.
ADTRAN Customer Service
ADTRAN Telco Technical Support .... (800) 726-8663
Standard support hours........................ Monday-Friday
7 a.m. - 7 p.m. CST
Emergency support ............ 7 days/week, 24 hours/day
Sales ................................................... (800) 827-0807
Customer and Product Support
(CAPS) ............................................... (256) 963-8722
Repair and Return Address
ADTRAN, Inc.
Customer and Product Support (CAPS)
901 Explorer Boulevard
Huntsville, Alabama 35806-2807
61245065L1-5A
Section 61245065L1-5, Issue 1
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising