Acnodes | RM6821 | User manual | Acnodes RM6821 High Brightness - Sunlight Readable User Manual

Acnodes RM6821 High Brightness - Sunlight Readable User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please v is it Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA 91710
Tel: 909. 597. 7588
© C opyright 2015 Acnodes C orp.
Fax: 909. 597. 1939
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this
document is subject to change without notice. We are not liable for any injury or loss that r esults from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the dev ice. Save this manual for future reference.
¦
Unplug eq uipment before cleani ng. Don’t use liquid or spray detergent; use a moist cloth.
¦
Keep equipmen t away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
¦ When installing , place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
¦ When the equipment is in an open position, do not cover, block or in an y way obstruct the gap between it and the
po wer supply. Prop er air convection is necessary to keep it from overheating.
¦ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
¦
If you are using a power co rd th at did n’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratin gs la bel. The voltage rating on th e cord should be high er tha n the one listed
on the equipment’s ratings label.
¦
Observe all pre cautio ns an d warnings attached to the equipment.
¦
If you don’t inte nd on using the e quipment for a l ong time, disconnect it from the power outlet to prevent being
¦
Keep all liquids away from the e quipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
¦
Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
damaged by transient over-voltage.
invalidate its warranty.
¦
If any part of th e equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
¦ Any product, on which the serial number has been defaced, modified or removed.
¦
Damage, deterioratio n or malfunction resulting from:
? Accident, misuse, neglect, fire, water, lightn ing, o r othe r acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
? Repair or attempted repair by an yone not authorized by us.
? Any damage of the product due to shipment.
? Removal or installation of the pr oduct.
? Causes external to the pro duct, such as electric power fluctuation or failure.
? Use of supplies or pa rts not meeting our specifications.
? Normal wear an d tea r.
? Any other causes wh ich does not relate to a product defect.
¦
Removal, installation , and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no g uarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o ff and on, the user is encou raged to try to correct the interference by one or more of
the following measures:
¦
Re-position or reloca te the receiving antenn a.
¦
Incre ase the separation between the equipment and receiver.
¦
Connect the eq uipment into an o utlet on a circuit different from that to which the receiver is connected.
Contents
< Part. 1 > RM 6821
1.1
1.2
1.3
Package Content
Structure Diagram & Dimension
Installation
P.1
P.1 - 2
P.3
< Part. 2 > Specifications / OSD / Remote Controller
2.1
2.2
2.3
Product Specifications
On-screen Display Operation ( OSD )
Picture In Picture ( PIP ) / Picture By Picture ( PBP )
P.4 - 5
P.6 - 7
P.8 - 9
< Part. 3 > Options
3.1
3.2
3.3
3.4
3.5
3.6
3G / HD / SD-SDI Broadcast-grade input
MCS Multi-display control solution
AV3.0 Upgrade :
DVI-D + VGA + HDMI + BNC + S-Video + Audio
HF21" Touchscreen : Resistive, Capacitive, Multi-touch
48V, 24V or 12VDC power
MIL-type or lockable connector
P.10
P.11
P.12
P.13
P.14
P.15
Before Installation
¦ It is very important to mount the equipment in a suitable cabinet or on a stable surface.
¦ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
¦
To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
¦
When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
¦
Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
¦
¦
Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1
Disconnect the power cord.
2
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
Disconnect the power cord.
2
Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
Gently wipe the surface. Use as little pressure as possible.
4
Wait until your monitor is completely dry before plugging it in and powering it up.
< Pa rt 1 >
< 1 .1 > Pac kag e C ontent
R M 6 8 2 1 u n it X 1
- 6 ft VG A c ab l e X 1
- Po w e r a d ap t e r X 1
- Po w e r c o rd X 1
- Fa ste n e r scre w fo r re a r b ra cke t x 2
< 1.2 > Stru cture D iag ra m
F ro n t v iew
1
P ow er ad apter
3
2
R e a r vie w
4
5
1
L CD panel
2
LC D m em brane
3
Latc h to release the display panel from the
rear brac ket
4
R ear m ounting bracket
5
P ower ad apter bask et
DV I -D
A udio
Po w er c ord
P ower B NC
S -V ideo
VGA
out - in - in
V ideo P C
S tan dar d
: D VI-D + VGA + H D M I w / sp eaker
AV3. 0 up gr ade
: D VI-D + VGA + H D M I + B NC + S-Vid eo + aud io
O ptio n
: SD I, U SB fo r tou ch screen & D C po wer
H DM I
< 1.2 > Dimension
Front View
Side View
UNIT : mm
Bottom View
1mm = 0.03937 inch
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
RM 6821
501.9 x 64 x 353 mm
19.8 x 2.5 x 13.9"
555 x 124 x 537 mm
21.9 x 4.9 x 21.1"
10 kg
22 lb
13 kg
28.6 lb
< 1.3 > Installation
Step
¦
¦
1
Mount the rear bracket with M6 screw set.
8 x M6 screw set are required.
M6 screw sets are not provided.
rear bracket
Step
¦
Insert the upper part of the RM 6821
display panel into the rear bracket.
Step
¦
3
Push the lower part of the RM 6821
display panel into the rear bracket.
Step
4
¦
Fix the RM 6821 display panel into the rear
bracket with two fasteners ( Left & right side ).
¦
Lock the RM 6821 display panel by the
latch ( on the bottom left & right side ).
Fastener screw
latch
2
< Part 2 >
< 2.1 > Product Specifications
LCD
Panel
Panel Size ( diagonal )
21.5-inch Widescreen TFT color LCD
Display pixel ( dots x lines )
Brightness ( typ. )
650
Contrast Ratio ( typ. )
5000:1
Color
16.7 M
Viewing Angle ( L/R/U/D )
Response Time ( ms )
0.248
Display Area ( mm )
476.64H x 268.11V
Surface treatment
Anti-glare
Surface hardness
3H
Backlight Type
LED
MTBF ( hrs )
Digital
50,000
HDMI
HDMI 1.1, CEA-861-D
DVI
DVI-D, TMDS single link
VGA
Analog 0.7Vp-p
Composite ( RCA )
NTSC & PAL
S-Video ( 4-pin )
NTSC & PAL
Plug & Play
DVI / VGA
VESA EDID structure 1.3
Synchronization
VGA
Separate, Composite & SOG
Audio Input
Connector
3.5mm stereo jack
Impedance / Power level
30kΩ / 750mV
Connector
3.5mm stereo jack
Resistance / Power level
30kΩ / 2.8V
Power
2 x 2W
Analog
Audio
Connectivity
89/89/89/89
16
Dot pitch ( mm )
Video
Connectivity
1920 x 1080
Audio Output
Speaker Output
*When the audio output is connected, speaker output is OFF
Power
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON
65W or less
Power saving mode
6W or less
Power button OFF
2W or less
Regulatory
Safety Approval
FCC & CE
Environmental
Conditions
Operating
Temperature
Humidity
0 to 50°C degree
20~90%, non-condensing
Storage
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
Product ( W x D x H )
501.9 x 64 x 353 mm
19.8 x 2.5 x 13.9 inch
Packing ( W x D x H )
555 x 124 x 537 mm
21.9 x 4.9 x 21.1 inch
Net Weight
10 kgs / 22 lbs
Gross Weight
Applicable
Format
DVI-D / VGA Input
13 kgs / 28.6 lbs
PC Signal
1920 x 1080 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 768 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
HDMI Input
PC Signal
Same as VGA
Video Signal
1080p : 50 / 60Hz
Audio Signal
1080i
: 50 / 60Hz
720p
: 50 / 60Hz
480p
: 60Hz
576p
: 50Hz
2ch Linear PCM ( 32 / 44.1 / 48 KHz )
< 2.2 > On-screen Display Operation ( OSD )
Membrane Switch
Function
Turn the monitor on or off
Display the OSD menu
Act as an Enter key to select screen setting options
Scroll through menu options and adjust
the displayed control
Exit the OSD screen
Go back to the previous on-screen sub-menu or
main menu
Remark : All LED touch buttons in WHITE light.
The LED of Power
touch button will flash continuously when there is no signal input.
1
All the LED touch buttons will automatically turn off after 10 minutes of idle status ( except the Power
2
Light up all membrane buttons, please press any button for 1 - 2 seconds ( except the Power
).
).
< 2.2 > On-screen Display Operation ( OSD )
1
Picture
Picture mode :
Standard / Vivid / Soft / User mode to choose Brightness :
Adjust background black level of the screen image
Contrast :
Adjust the difference between the image background
(black level) and the foreground (white level)
Hue:
Adjust the screen hue value
Saturation :
Adjust the saturation of the image color
Picture size :
Adjust the image size
Color temp :
Standard / Cool / Warm / User to choose
Noise reduce :
Reduce the noise of the image Sharpness :
Adjust the image from weak to sharp
2
3
PC
Auto adjust :
Automatically adjust sizes, centers and fine tunes the
video signal to eliminate waviness and distortion.
Clock :
Adjust the clock value
Phase :
Adjust the phase value
H. Position :
Align the screen image left or right
V. Position :
Align the screen image up or down
Audio
Audio mode :
Movie / Voice / Normal / Music mode to choose
Volume :
Adjust the volume of sound
Bass :
Set the value of bass sound
Treble :
Set the value of treble sound
Balance :
Set the balance value of treble and bass sound
Analog TV audio : Set the value of analog TV audio sound
Mute :
4
Turn off the surrounding sound
MISC
Language :
Select the language in which the OSD menu is
displayed - English
Sleep timer :
Set the off time
PIP mode :
Adjust picture in picture setting
PIP position :
Enter into PIP position
PIP source :
Enter into the Sub source and sound source
System reset :
Return the adjustment back to factory setting
Information :
Select for Help
< 2.3 > How to Use Picture In Picture ( PIP ) / Picture By Picture ( PBP )
< 2.3.1 > Picture in Picture ( PIP )
Mode
Display the Sub screen in the Main screen.
OSD Menu ? MISC ? PIP Mode ? Large / Small / OFF
Main screen
Sub screen
Position
Adjust the position of the Sub screen ( top left, bottom left, top right, bottom right )
OSD Menu ? MISC ? PIP Position ? top left / top right / bottom left / bottom right
top left
top right
bottom left
bottom right
Size
Adjust the size of the Sub screen ( Large / Small )
OSD Menu ? MISC ? PIP Mode ? Large / Small
Size of Sub screen
LCD Monitor
Large Sub screen
Small Sub screen
1920 x 1200
552 x 414
480 x 360
1920 x 1080
552 x 414
480 x 360
1440 x 900
1366 x 768
414 x 310
392 x 294
360 x 270
340 x 254
1280 x 1024
368 x 276
320 x 240
< 2.3.2 > Picture By Picture ( PBP )
Mode
Display the Sub screen next to the Main screen.
OSD Menu ? MISC ? PIP Mode ? PBP
Main screen
Sub screen
Size
LCD Monitor
1920 x 1200
Main / Sub screen
955 x 716
1920 x 1080
1440 x 900
955 x 716
715 x 536
1366 x 768
1280 x 1024
678 x 508
635 x 476
< 2.3.3 > PIP / PBP Source
To select an input signal for PIP / PBP Sub screen.
OSD Menu ? MISC ? PIP Source ? VGA / S-Video / Composite / DVI / HDMI / SDI / YPbPr / TV
The PIP / PBP is operable in the following table :
Sub
VGA
S-Video
Composite
DVI-D
HDMI
SDI
YPbPr
TV
VGA
x
o
o
o
o
o
o
o
S-Video
o
x
x
o
o
o
o
x
Composite
o
x
x
o
o
o
o
x
DVI
o
o
o
x
x
o
o
o
HDMI
o
o
o
x
x
o
o
o
SDI
o
o
o
o
o
x
x
o
YPbPr
o
o
o
o
o
x
x
o
TV
o
x
x
o
o
o
o
x
Main
< P art 3 >
< 3.1 > Optio ns : 3G / HD / SD-SDI input
Acnodes ’ SD I input is an ideal solution for the broadcastgrade video and high resolution CC TV market.
D esigned for use with F ull H D 1080p and ultra high resolution
1920 x 1200 LC D displays, Acnodes provides a SD I input
module w ithout using additional space or power and it com es
standard with a 2- year warranty.
SDI
Audio
DVI-D
Po wer
BNC S-Video
VGA
out - in - in
Video PC
***
HDMI
out
-
in
F or SDI option, the AD board w ill be upgraded to AV3.0, and this comes standard w ith H D MI, DVI -D,
VG A, S-Video, BN C and audio inputs.
IN PU T
Standard C om plian ce
C om patible Video F ormat
C om patible A udio F ormat
Max. Transm ission Distance
75 ohm coaxial cab le
3G-SD I IN
BN C x 1 / 0.8Vp-p ( 75 ohm )
3G-SD I O UT
BN C x 1 / Active through, equalized & r eloc ked
Video
SMPT E 425M / 274M / 296M / 125M
ITU -R BT.656
Audio
SMPT E 299M / 272M-C
3G-SD I
1080p
1080p
1080i
720p
@60
@30
@60
@60
H D-SD I
1080p
1080i
720p
@30 / 25 / 24H z, 4:2:2
@60 / 50Hz, 4:2:2
@60 / 50Hz, 4:2:2
SD -SD I
480i
@60H z, 4:2:2
IT U-R BT.656
576i
@50H z, 4:2:2
3G-SD I
48kHz, 16 / 20 / 24 bit, 2 CH , Synchronized Video
H D-SD I
48kHz, 16 / 20 / 24 bit, 2 CH , Synchronized Video
SD -SD I
48kHz, 16 / 20 / 24 bit, 2 CH , Synchronized /
As ynchronized Video
3G-SD I
150m at 2.97G b/s
H D-SD I
250m at 1.485Gb/s
SD -SD I
480m at 270Mb/s
/ 50Hz, 4:2:2
/ 25 / 24H z, 4:4:4
/ 50Hz, 4:4:4
/ 50Hz, 4:4:4
< 3.2 > Options : MCS
( Multi-display Control )
More control is always good. Especially when it is necessary and
easy. Acnodes provides MCS solution to control the OSD of
various LCD display up to 64 units.
The RS-232C is used for the communication between the PC and the
first display via a 15 feet serial cable while the CAN bus is used for the
various LCD displays cascade together via CAT 5/6 cable, and daisy
chain up to 1,000 meters.
Designed for use with various LCD displays, Acnodes provides a
MCS input module without using additional space or power and it
comes standard with a 2-year warranty.
Audio
HDMI
Power BNC S-Video
out - in - in
Video PC
VGA
***
MCS
DVI-D
set out
in
Link
For MCS option, casing depth will be changed.
Set switch
For the 1st and last display,
push the set switch upward
RS-232C
For other daisy chain displays,
push the set switch downward
15 feet serial cable
( over 15 feet, extender required )
LINK
OUT
IN
Cat5 / 6 cable
max. 300 meters
OUT
IN
Cat5 / 6 cable
max. 300 meters
OUT
IN
OUT
Cat5 / 6 cable
max. 300 meters
RJ-45 jack
Daisy chain up to 1,000
meters and 64 displays
up to 64 displays
< 3.3 > AV3.0 Upgrade Options :
- AV
( S-Video + Composite, BNC )
- Audio ( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
Audio
DVI-D
Power BNC S-Video
VGA
HDMI
out - in - in
Video PC
< 3.4 > Options : Touchscreen & driver
21.5" USB Touchscreen Specification
Model
TRB
e-Resistive
TCB
e-Capacitive
TMC2
Multi-touch
Technology
5-Wire Resistive
Capacitive
Projected Capacitive
Touch Point
Single
Single
Dual
Stylus or Finger
Finger
Finger
= 50g / Stylus=R0.8
= 50g
= 50g
10 million touches
300 million touches
100 million touches
15 ms
20 ms
20 ms
80% ± 3%
87% ±2%
90% ±2%
3H
9H
7H
Haze
8% ± 3%
7%
3%
Glass
3.2 ±0.2 mm
2.8 mm ±10%
2.4 ±0.15 mm
Method
Activation Force
Durability
Response Time
Optical Transmittance
Surface Hardness
Connector
Compatibility
¦
¦
¦
USB Type A
USB Type A
Windows 7 / XP / Vista, Linux
Windows 7
USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
For detailed information, please refer to the attached CD disc
As the touchscreen unit is not made of toughened glass, please handle it carefully
USB Touchscreen
DVI-D
Power
VGA
HDMI
Please follow the below steps to setup the touch screen:Step 1. Run the bundled CD disc
Step 2. Double click the Setup.exe
Step 3. Follow the installation instruction to finish the setup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please do the initial calibration
after the first setup
< 3.4 > Options : Touchscreen & driver
TMC2 Driver
Connect the USB cable from the USB port on the LCD to a computer. The touch screen supports
easy Plug-and-Play operations. There is no need to install additional drivers on the computer.
< 3.5 > Options : DC Power
Model
24V
48V
24-Volt
48-Volt
18 ~ 36V
36 ~ 75V
- No load
50 mA
50 mA
- Full load
4880 mA
2442 mA
Output voltage:
12-Volt
12-Volt
Output current:
8.3A
8.3A
Efficiency
85%
86%
Input rating
Input voltage:
Input range:
Input current
Output rating
< 3.6 > Options : MIL-type or Lockable Connector
Input
MIL - type
Connector
Part no.
MIL Standard
DC Power ***
( Male )
MS3470W8-33P
MIL - DTL - 26482
VGA ***
( Male )
MS3470W14-15P
MIL - DTL - 26482
*** There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with the most
design flexibility possible. For more information, please contact us.
Input
Lockable
Connector
Part no.
DC Power
( Male )
YM-Ext-461CP001
USB
LUSB - A111 - 00
Standard
D-type 3W3
-
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising