Acnodes | PMW6170 | User manual | Acnodes PMW6170 Open Frame - 1080P / 4K User Manual

Acnodes PMW6170 Open Frame  - 1080P / 4K User Manual
Industrial Monitors
PMW6170
17 ” 1 9 2 0 x 1 2 0 0 W i d s c r e e n L C D
Open Frame Metal Construction
Wall/ Panel/ VESA Mount Read y
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA91710
Tel: 909.597.7588
© Copyright 2015 Acnodes Corp.
Fax: 909.597.1939
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the
contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from
the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
● Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
● Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
● When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing dam
age to other equipment or injury to persons nearby.
● When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
● Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
● If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
● Observe all precautions and warnings attached to the equipment.
● If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being dam
aged by transient over-voltage.
● Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
● Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invali date its warranty.
● If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
● Any product, on which the serial number has been defaced, modified or removed.
● Damage, deterioration or malfunction resulting from:
● Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
● Repair or attempted repair by anyone not authorized by us.
● Any damage of the product due to shipment.
● Removal or installation of the product.
● Causes external to the product, such as electric power fluctuation or failure.
● Use of supplies or parts not meeting our specifications.
● Normal wear and tear.
● Any other causes which does not relate to a product defect.
● Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential instal- lation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
● Re-position or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Contents
< Part. 1 > PMW 6170
1.1
1.2
1.3
Package Content
Structure Diagram & Dimension
Mounting Hardware & Installation
P.1
P.2 - 3
P.4
< Part. 2 > Specifications I OSD I Remote Controller
2.1
2.2
2.3
Product Specifications
On-screen Display Operation ( OSD )
Remote Controller ( RC-2 )
P.5 - 6
P.7 - 8
P.9
< Part. 3 > Options
3.1
3.2
3.3
3.4
3.5
3.6
3.7
Option Table
3G / HD / SD-SDI Broadcast-grade input
MCS Multi-display control solution
17" Touchscreen : Resistive, Capacitive
48V, 24V or 12VDC power
MIL-type or lockable connector
TV ( Analog )
P.10
P.11
P.12
P.13
P.14
P.15
P.16
Before Installation
● It is very important to mount the equipment in a suitable cabinet or on a stable surface.
● Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
●
●
●
●
●
To avoid the r isk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1
Disconnect the power cord.
2
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
Disconnect the power cord.
2
Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
Gently wipe the surface. Use as little pressure as possible.
4
Wait until your monitor is completely dry before plugging it in and powering it up.
< Part 1 >
< 1.1 > Package Content- PMW6170
PMW6170
17” Widescreen LCD display X 1
6ft VGA cable X 1
Power cord X 1
Remote controller X 1
Standard IIO
Power BNC S-Video
Audio
HDMI
DVI-D
VGA
out - in - in
Video PC
- An abundance of input connections that include HDMI, DVI-D, VGA, S-Video + BNC and audio
- On-chip Faroudja® DCDi Cinema processing
< 1.2 > Structure Diagram - PMW 6170
1
Front view
2
3
6
1
Rear case
2
LCD panel
3
Audio speaker, pair
4
4
Universal open frame mounting
5
5
LCD membrane
6
Extended remote sensor membrane cable
Rear view
( 66cm from AD board to sensor end )
Model
PMW6170
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
466 x 51 x 328 mm
18.3 x 2 x 12.9 inch
615 x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
3.7 kg
8.1 lbs
6.2 kg
13.6 lbs
< 1.2 > Dimension-PMW 6170
Front View
Rear View
Side View
UNIT : mm
1mm = 0.03937 inch
Bottom View
< 1.3 > Installation
( I ) Universal mount
( II ) VESA mount ( 100*100mm )
M 4 screw
Hardware and M4*4 pcs for VESA mounting are not provided
< Part 2 >
< 2.1 > Product Specifications
Mechanical
Design
PMW 6170
Front Panel
-
Rear Casing
Dark grey, RAL 7037
VESA Mounting
100 x 100mm
Other Mounting
Universal mount
Protection
LCD
Panel
-
Panel Size ( diagonal )
17.1-inch Widescreen TFT color LCD
Display pixel ( dots x lines )
1920 x 1200
Brightness ( typ. )
210
Contrast Ratio ( typ. )
600:1
Color
16.7M, 8-bit
Viewing Angle ( L/R/U/D )
65/65/55/55
Response Time ( ms )
30
Dot pitch ( mm )
0.191
Display Area ( mm )
367.20H x 229.50V
Surface treatment
Anti- glare, Hard-coating
Surface hardness
3H
Backlight Type
LED
MTBF ( hrs )
Video
Connectivity
Digital
HDMI
HDMI 1.1, CEA-861-D
DVI
DVI-D, TMDS single link
VGA
Analog 0.7Vp-p
Composite ( RCA )
NTSC & PAL
S-Video ( 4-pin )
NTSC & PAL
Plug & Play
DVI / VGA
VESA EDID structure 1.3
Synchronization
VGA
Separate, Composite & SOG
Audio Input
Connector
3.5mm stereo jack
Impedance / Power level
30k K / 750mV
Connector
3.5mm stereo jack
Resistance / Power level
30k K / 2.8V
Power
2 x 2W
Analog
Audio
Connectivity
20,000
Audio Output
Speaker Output
*When the audio output is connected, speaker output is OFF
Power
Power Supply
Power Consumption
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Screen display ON
34W or less
Power saving mode
4W or less
Power button OFF
1W or less
Regulatory
Safety Approval
FCC & CE
Environmental
Conditions
Operating
Temperature
Humidity
0 to 50°C degree
20~90%, non-condensing
Storage
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Physical
Specification
Product ( W x D x H )
466 x 51 x 328 mm
18.3 x 2 x 12.9 inch
Packing ( W x D x H )
615 x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
Net Weight
3.7 kgs / 8.1 lbs
Gross Weight
Applicable
Format
DVI-D / VGA Input
6.2 kgs / 13.6 lbs
PC Signal
1920 x 1200 x 60Hz
1920 x 1080 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 768 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
HDMI Input
Composite / S-Video
Input
PC Signal
Same as VGA
Video Signal
1080p : 60Hz
720p
: 50 / 60Hz
480p
: 60Hz
576p
: 50Hz
Audio Signal
2ch Linear PCM ( 32 / 44.1 / 48 KHz )
NTSC
525 lines, 60 fields / sec
PAL
625 lines, 50 fields / sec
< 2.2 > On-screen Display Operation ( OSD )
Power light
Green = On
Orange = Power saving
Membrane Switch
Function
Power on / off LCD
Display the OSD menu
Scrolls through menu options and adjusts the displayed control
(To auto adjustment by pressing the button
for 5 seconds)
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
1
Picture
Picture mode :
Standard / Vivid / Soft / User mode to choose
Brightness :
Adjust background black level of the screen image
Contrast :
Adjust the difference between the image background
Hue:
Adjust the screen hue value
Saturation :
Adjust the saturation of the image color
Picture size :
Adjust the image size
(black level) and the foreground (white level)
2
Color temp :
Standard / Cool / Warm / User to choose
Noise reduce :
Reduce the noise of the image
Sharpness :
Adjust the image from weak to sharp
PC
Auto adjust :
Automatically adjust sizes, centers and fine tunes the
video signal to eliminate waviness and distortion.
Clock :
Adjust the clock value
Phase :
Adjust the phase value
H. Position :
Align the screen image left or right
I. Position :
Align the screen image up or down
< 2.2 > On-screen Display Operation ( OSD )
3
Audio
Audio mode :
Movie / Voice / Normal / Music mode to choose
Volume :
Adjust the volume of sound
Bass :
Set the value of bass sound
Treble :
Set the value of treble sound
Balance :
Set the balance value of treble and bass sound
Analog TV audio : Set the value of analog TV audio sound
Mute :
4
5
Turn off the surrounding sound
TV
Auto search :
Automatically search
Manual search :
Search the TV manual
Fine tune :
Fine tune the TV signal
Color system :
Adjust the TV color
Sound system :
Adjust the TV sound
Channel edit :
Edit the channel
MISC
Language :
Select the language in which the OSD menu is
displayed - English
Sleep timer :
Set the off time
PIP mode :
Adjust picture in picture setting
PIP position :
Enter into PIP position
PIP source :
Enter into the Sub source and sound source
System reset :
Return the adjustment back to factory setting
Information :
Select for Help
< 2.3 > Remote Controller ( RC-2 )
1
8
2
INP UT
3
4
MUTE
1
2
3
4
5
6
7
8
9
AUTO
0
-/--
VOL
9
CH
10
F REE ZE
11
12
ME NU
5
SE LECT
AS P ECT
13
14
6
SLEEP
ENTE R
15
16
7
BA CK
EXIT
PIP
POS ITION
AUDIO
17
PIP
20
S OURCE
SWAP
18
PIP
21
19
r
1
INPUT
Select the source
Switches on or off the TV
2
3
0-9
Only use in TV mode. Select channels. For channel numbers 10
and above, enter the second digit within two seconds.
4
AUTO
MENU
Auto adjust
5
6
? / ? / ? / ? / ENTER
7
BACK
MUTE
Vol + I CH + I FREEZE
- I -ASPECT
SELECT
SLEEP
EXIT
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PIP functions
PIP
PIP AUDIO
POSITION
SOURCE
SWAP
Display the menu on the screen or go to the previous menu
Go to the upper menu or select the previous value /
Go to the next menu or select the next value /
Decrease the setting value /
Increase the setting value or enter to the select item setting
Enter to the select item settings or excude the setting
Back to previous value
Turn on or off the speaker
Increase or decrease the speaker volume
For TV model only, increase or decrease the channel number
Reserve for OEM model
For setting input single or double digits
Adjust the screen size
To select the existing item
Select the sleeping time
Exit the menu or cancel
Picture in picture
To set the audio of in PIP mode
To set the screen position in PIP mode
PIP Source
Swap screen in PIP mode
< Part 3 > Options
< 3.1 > Option Table
Options
APW
SDI ***
Touchscreen
MCS multi-display control ***
DC Power
MIL-type / lockable connector
TV ( Analog )
***
The user can only select either SDI or MCS inputs.
PMW
< 3.2 > Options : 3G I HD I SD-SDI input
Acnodes’ SDI input is an ideal solution for the broadcastgrade video and high resolution CCTV market.
Designed for use with Full HD 1080p and ultra high resolution
1920 x 1200 LCD displays, Acnodes provides a SDI input
module without using additional space or power and it comes
standard with a 2- year warranty.
SDI
Power BNC S-Video
Audio
DVI-D
VGA
HDMI
out - in - in
Video PC
INPUT
Standard Compliance
Compatible Video Format
Compatible Audio Format
Max. Transmission Distance
75 ohm coaxial cable
out
-
in
3G-SDI IN
BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT
BNC x 1 / Active through, equalized & relocked
Video
SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio
SMPTE 299M / 272M-C
3G-SDI
1080p
1080p
1080i
720p
@60 / 50Hz, 4:2:2
@30 / 25 / 24Hz, 4:4:4
@60 / 50Hz, 4:4:4
@60 / 50Hz, 4:4:4
HD-SDI
1080p
1080i
720p
@30 / 25 / 24Hz, 4:2:2
@60 / 50Hz, 4:2:2
@60 / 50Hz, 4:2:2
SD-SDI
480i
@60Hz, 4:2:2
ITU-R BT.656
576i
@50Hz, 4:2:2
3G-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Asynchronized Video
3G-SDI
150m at 2.97Gb/s
HD-SDI
250m at 1.485Gb/s
SD-SDI
480m at 270Mb/s
< 3.3 > Options : MCS
MCS
( Multi-display Control )
More control is always good. Especially when it is necessary and
easy. Acnodes provides MCS solution to control the OSD of
various LCD display up to 64 units.
The RS-232C is used for the communication between the PC and
the first display via a 15 feet serial cable while the CAN bus is
used for the various LCD displays cascade together via CAT 5/6
cable, and daisy chain up to 1,000 meters.
Designed for use with various LCD displays, Acnodes provides
a MCS input module without using additional space or power
and it comes standard with a 2-year warranty.
MCS
Power BNC S-Video
Audio
DVI-D
VGA
HDMI
set out
out - in - in
Video PC
in
Link
Set switch
For the 1st and last display,
push the set switch upward
RS-232C
For other daisy chain displays,
push the set switch downward
15 feet serial cable
( over 15 feet, extender required )
LINK
OUT
IN
Cat5 / 6 cable
max. 300 meters
OUT
IN
Cat5 / 6 cable
max. 300 meters
OUT
IN
OUT
Cat5 / 6 cable
max. 300 meters
RJ-45 jack
Daisy chain up to 1,000
meters and 64 displays
up to 64 displays
< 3.4 > Options : Touchscreen & driver
17" USB Touchscreen Specification
Model
TRB
e-Resistive
TCB
e-Capacitive
Technology
5-Wire Resistive
Capacitive
Touch Point
Single
Single
Stylus or Finger
Finger
= 50g / Stylus=R0.8
= 50g
10 million touches
300 million touches
15 ms
20 ms
80% ± 3%
92% ±2%
3H
9H
Haze
8% ± 3%
7%
Glass
2.2 ±0.2 mm
2.8 mm ±10%
Method
Activation Force
Durability
Response Time
Optical Transmittance
Surface Hardness
Connector
USB Type A
Compatibility
●
●
●
Windows 7 / XP / Vista, Linux
USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
For detailed information, please refer to the attached CD disc
As the touchscreen unit is not made of toughened glass, please handle it carefully
USB Touchscreen
Power BNC S-Video
Audio
out - in - in
Video PC
HDMI
DVI-D
VGA
Please follow the below steps to setup the touch screen:Step 1. Run the bundled CD disc
Step 2. Double click the Setup.exe
Step 3. Follow the installation instruction to finish the setup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please do the initial calibration
after the first setup
< 3.5 > Options : DC Power
Model
12V
24V
48V
Input voltage:
12-Volt
24-Volt
48-Volt
Input range:
9 ~ 18V
18 ~ 36V
36 ~ 75V
- No load
50 mA
50 mA
50 mA
- Full load
4950 mA
2450 mA
1220 mA
Output voltage:
12-Volt
12-Volt
12-Volt
Output current:
4 .16A
4.16A
4.16 A
Efficiency
84%
85%
85%
Input rating
Input current
Output rating
< 3.6 > Options : MIL-type or Lockable Connector
Input
MIL - type
Connector
Part no.
MIL Standard
DC Power ***
( Male )
MS3470W8-33P
MIL - DTL - 26482
VGA ***
( Male )
MS3470W14-15P
MIL - DTL - 26482
*** There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with
design flexibility possible. For more information, please contact us.
Input
Lockable
Connector
Part no.
DC Power
( Male )
YM-Ext-461CP001
USB
LUSB - A111 - 00
the
Standard
D-type 3W3
-
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
most
< 3.7 > Options : TV ( Analog )
TV
Power BNC S-Video
Audio
DVI-D
VGA
HDMI
HDMI
out - in - in
Video PC
PC
***
( 1 ) For TV option, casing dimensions will be changed.
( 2 ) For RC-2 remote controller specifications, please refer to P.14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising