Acnodes | PMH9190 | User manual | Acnodes PMH9190 Open Frame - High Brightness LCD Display User Manual

Acnodes PMH9190 Open Frame  - High Brightness LCD Display User Manual
I n d u s t r i a l Monit or s
PMH9190
19 ” 1 4 4 0 x 9 0 0 Wide scree n L CD
O p e n F r a m e M e ta l Co n s t r u c t i o n
1 0 0 0 - n i t Hi g h B r i g h tn e s s L CD
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please v is it Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA 91710
Tel: 909. 597. 7588
© C opyright 2015 Acnodes C orp.
Fax: 909. 597. 1939
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correct ness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■
■
■
■
■
■
■
■
■
■
■
Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
Observe all precautions and warnings attached to the equipment.
If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
■
■
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
■
Accident, misuse, neglect, fire, water, lightning, or other acts of nat ure, unaut horized product modification, or
failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Caus es external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
□
□
□
□
□
□
□
□
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been t ested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance wit h the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If t his equipment does cause
harmful interference to radio or television rec eption, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■ Re-position or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Contents
< Part. 1 > PMH9190
1.1
1.2
1.3
Package Content
Structure Diagram & Dimension
Mounting Hardware & Installation
P.1
P.2 - 3
P.4
< Part. 2 > Specifications / OSD
2.1
2.2
Product Specifications
On-screen Display Operation ( OSD )
P.5 - 6
P.7
< Part. 3 > Options
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
Option Table
3G / HD / SD-SDI Broadcast-grade input
MCS Multi-display control solution
AV2.2D Upgrade : DVI-D, S-Video + BNC & Audio
AV2.2H Upgrade : HDMI, S-Video + BNC & Audio
AV3.0 Upgrade : HDMI, DVI-D, S-Video + BNC & Audio
Resistive / Capacitive ( single point touch )
48V or 24VDC power
MIL-type or lockable connector
Quad display for CCTV
TV ( Analog )
Auto / switch dimming
P.8
P.9
P.10
P.11 - 12
P.13
P.14 - 15
P.16
P.17
P.18
P.19 - 20
P.21
Before Installation
■ It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
■
■
■
■
■
To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1
Disconnect the power cord.
2
Gently wipe the surfac e using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
Disconnect the power cord.
2
Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or apply a ny liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
Gently wipe the surface. Use as little pressure as possible.
4
Wait until your monitor is completely dry before plugging it in and powering it up.
< Part 1 >
< 1.1 > Package Content
PMH9190
W19" High Brightness LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
Basic I/O
Power
DVI-D
VGA
DVI-D
VGA
AV2.2D upgrade I/O
Power BNC S-Video
Audio
out - in - in
Video PC
AV2.2H upgrade I/O
Power BNC S-Video
Audio
VGA
HDMI
out - in - in
Video PC
AV3.0 upgrade I/O with advanced features
Power BNC S-Video
Audio
DVI-D
VGA
HDMI
out - in - in
Video PC
- An abundance of input connections that include HDMI, DVI-D, VGA, S-Video + BNC and audio
- On-chip Faroudja® DCDi Cinema processing
< 1.2 > Structure Diagram
1
Front view
2
3
6
Rear view
1
Rear case
2
LCD panel
3
Audio speaker ( for HDMI, Audio or TV option )
4
Universal open frame mounting
5
LCD membrane
6
Extended remote sensor membrane cable
4
5
( 66cm from AD board to sensor end )
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
PMH9190
505.5 x 59.6 x 335.1 mm
19.9 x 2.3 x 13.2 inch
662 x 115 x 533 mm
26.1 x 4.5 x 21 inch
5 kg
11 lbs
10 kg
22 lbs
< 1.2 > Dimension
Front View
Rear View
Side View
UNIT : mm
1mm = 0.03937 inch
Bottom View
< 1.3 > Installation
( I ) Universal mount
( II ) VESA mount ( 100*100mm )
M4 screw
Hardware and M4*4 pcs for VESA mounting are not provided
< Part 2 >
< 2.1 > Product Specifications
Mechanical
Design
PMH9190
Front Panel
-
Rear Casing
Dark grey, RAL 7037
VESA Mounting
100 x 100mm
Other Mounting
Universal mount
Protection
LCD
Panel
-
Panel Size ( diagonal )
19-inch Widescreen TFT color LCD
Display pixel ( dots x lines )
1440 x 900
Brightness ( typ. )
1000
Contrast Ratio ( typ. )
1000:1
Color
16.7 M
Viewing Angle ( L/R/ U/D )
80/80/ 80/80
Response Time ( ms )
5
Dot pitch ( mm )
0.2835
Display Area ( mm )
408.24H x 255.15V
Surface treatment
Haze 25%, Hard-coating
Surface hardness
3H
Backlight Type
LED
MTBF ( hrs )
Video
Co nnec tivity
Analog
Power
Power Supply
Power Consumption
Regulatory
Environmental
Conditions
50,000
VGA
Analog 0.7Vp-p
Range
Auto-sensing 100 to 240VAC,
50/60Hz
Screen display ON
35W or less
Power saving mode
4W or less
Power button OFF
1W or less
Safety
FCC & CE certified
Environmental
RoHS2 & REACH compliant
Operating
Temperature
0 to 50°C degree
Humidity
20~90%, non-condensing
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Storage
Physical
Specification
Product ( W x D x H )
505.5 x 59.6 x 335.1 mm
Packing ( W x D x H )
19.9 x 2.3 x 13.2 inch
662 x 115 x 533 mm
26.1 x 4.5 x 21 inch
Net Weight
5 kgs / 11 lbs
Gross Weight
Applicable
Format
VGA Input
10 kgs / 22 lbs
PC Signal
1440 x 900 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 760 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
< 2.2 > On-screen Display Operation ( OSD )
Power light
Green = On
Orange = Power saving
Membrane Switch
Function
Power on / off LCD
Display the OSD menu
Scrolls through menu options and adjusts the displayed control
(To auto adjustment by pressing the button
for 5 seconds)
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
OSD Configuration Page
Image:
for the brightness, contrast, color temp, red, green, and blue
Geometry:
for the auto adjust, H position, V position, phase and clock
Video:
for the colour, tint, sharpness, noise reduction, DCDi and TV Setup
Audio:
for volume, bass, treble, balance, AVL and mute
Misc:
for the language, OSD position, graphic mode, ratio, reset and timer
< Part 3 > Options
< 3.1 > Option Table
Options
PMH
SDI ***
HDMI * or DVI-D
S-Video * + Composite ( BNC )
Audio
Touchscreen
MCS multi-display control
DC Power
MIL-type / lockable connector
Quad display
TV ( Analog ) *
Auto / switch dimming
About SDI
***
( 1 ) The AD board will be upgraded to version 3.0, and this comes standard with HDMI, DVI-D,
VGA, S-Video, BNC, audio inputs and RC-1 remote controller.
HDMI and DVI-D
*( 1 )About
For AV2.2 upgrade, either HDMI or DVI-D i s provided.
( 2 ) If the user needs HDMI and DVI-D, AV3.0 upgrade can be applied.
Controller
*( 1 )Remote
AV2.2 upgrade comes with RC-1 remote controller.
( 2 ) TV option comes with RC-2 remote controller.
< 3.2 > Options : 3G / HD / SD-SDI input
Acnodes’ SDI input is an ideal solution for the broadcast- grade
video and high resolution CCTV market.
Designed for use with Full HD 1080p and ultra high resolution
1920 x 1200 LCD displays, Acnodes provides a SDI input
module without using additional space or power and it comes
standard with a 2-year warranty.
SDI
Power BNC S-Video
Audio
DVI -D
VGA
HDMI
out - in - in
Video PC
***
out -
in
For SDI option, the AD board will be upgraded to AV3.0, and this comes standard with HDMI, DVI-D,
VGA, S-Video, BNC, audio inputs and RC-1 remote controller
INPUT
Standard Compliance
Compatible Video Format
Compatible Audio Format
Max. Transmi ssion Di stance
75 ohm coaxial cable
3G-SDI IN
BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT
BNC x 1 / Active through, equalized & relocked
Video
SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio
SMPTE 299M / 272M-C
3G-SDI
1080p
1080p
1080i
720p
@60 /
@30 /
@60 /
@60 /
HD-SDI
1080p
1080i
720p
@30 / 25 / 24Hz, 4:2:2
@60 / 50Hz, 4:2:2
@60 / 50Hz, 4:2:2
SD-SDI
480i
@60Hz, 4:2:2
ITU-R BT.656
576i
@50Hz, 4:2:2
3G-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Asynchronized Video
3G-SDI
150m at 2.97Gb/s
HD-SDI
250m at 1.485Gb/s
SD-SDI
480m at 270Mb/s
50Hz, 4:2:2
25 / 24Hz, 4:4:4
50Hz, 4:4:4
50Hz, 4:4:4
< 3.3 > Options : MCS
More control is always good. Especially when it is necessary and
easy. Acnodes provides MCS solution to control the OS D of
various LCD display up to 64 units.
MCS
( Multi-display Control )
The RS-232C is used for the communication bet ween the PC and
the first display via a 15 feet serial cable while the CA N bus is
used for the various LCD displays cascade together via CAT 5/6
cable, and daisy chain up to 1,000 meters.
Designed for use with various LCD displays, Acnodes provides
a MCS input module without using additional space or power
and it comes standard with a 2-year warranty.
MCS
Audio
Power BNC S-Video
DVI -D
VGA
HDMI
out - in - in
Video PC
set out
in
Link
*** Please download the protocol of MCS control at :
http://www.acnodes.com/files/downloads/MCS-UM.pdf
Set switch
For the 1st and last display,
push the set switch upward
RS-232C
For other daisy chain displays,
push the set switch downward
15 feet serial cable
( over 15 feet, extender required )
LINK
O UT
IN
Cat5 / 6 cable
max. 300 meters
O UT
IN
Cat5 / 6 cable
max. 300 meters
O UT
IN
OUT
Cat5 / 6 cable
max. 300 meters
RJ-45 jack
Daisy chain up to 1,000
meters and 64 displays
up to 64 displays
< 3.4 > Options :
AV2.2D Upgrade Options
- DVI-D ( DVI-D TMDS single link )
- AV
( S-Video + Composite, BNC )
- Audio ( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
Power BNC S-Video
Audio
DVI -D
VGA
out - in - in
Video PC
AV2.2H Upgrade Options
- HDMI ( HDMI 1.1, CEA-861-D )
- AV
( S-Video + Composite, BNC )
- Audio ( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
Power BNC S-Video
Audio
VGA
HDMI
out - in - in
Video PC
***
AV2.2 upgrade option comes with RC-1 remote controller x 1.
5
1
2
3
6
7
4
8
9
1
POWER
Sw itches on or off the TV
2
MUTE
Turn on or off the speaker
3
AV
Sw itch to AV mode
4
0- 9
Select channels. For channel numbers 10 and above,
enter the second digit within tw o seconds.
5
V +/-
Increase or decrease the speaker volume
6
CH + / -
Increase or decrease the channel number
7
MENU
Display the menu on the screen or go to the previous menu
8
AUTO
For auto searching
9
-/-
For setting one or two input digit
< 3.5 > AV3.0 Upgrade Options :
- HMDI
- DVI-D
- AV
- Audio
Power BNC S-Video
( HDMI 1.1, CEA-861-D )
( DVI-D TMDS single link )
( S-Video + Composite, BNC )
( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
Audio
HDMI
out - in - in
Video PC
DVI -D
VGA
< 3.6 > Options : Touchscreen & driver
HW19" USB Touchscreen Specification
Model
TRB
e-Resistive
TCB
e-Capacitive
Technology
5-Wire Resistive
Capacitive
Touch Point
Single
Single
Input Type
Finger or Stylus
Finger
Resolution
2048 x 2048
2048 x 2048
-
-
Response Speed
15 ms
20 ms
Activation Force
≤ 50 g
≤ 50 g
3H
9H
80% ± 3%
92% ± 2%
8% ± 3%
7%
Durability Top
10 million touches
300 million touches
Layer Bottom
ITO Film
Touch Point Accuracy
Surface Hardness
Light Transmi ssion
Haze
Layer
Glass
ITO Glass
Thickne ss
3.2 ± 0.2 mm
2.8 mm ± 10%
Connector
USB Type A
USB Type A
Compatibility
■
■
■
Windows 7 / XP / Vista, Linux
USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
For detailed information, please refer to the attached CD disc
As the touchscreen unit is not made of toughened glass, please handle it carefully
USB Touchscreen
Power
DVI -D
VGA
< 3.6 > Options : Touchscreen & driver
TRB / TCB Driver
Please follow the below steps to setup the touch screen:Step 1. Run the bundled CD disc
Step 2. Double click the Setup.exe
Step 3. Follow the installation instruction to finish the setup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please do the initial calibration
after the first setup
< 3.7 > Options : DC Power
Model
24V
48V
Input rating
Input voltage:
24-Volt
48-Volt
18 ~ 36V
36 ~ 75V
- No load
50 mA
50 mA
- Full load
4880 mA
2442 mA
Output voltage:
12-Volt
12-Volt
Output current:
8.3A
8.3A
Efficienc y
85%
86%
Input range:
Input current
Output rating
< 3.8 > Options : MIL-type or Lockable Connector
Input
MIL - type
Connector
Part no.
MIL Standard
DC Power ***
( Male )
MS 3470W 8- 33P
MIL - DTL - 26482
VGA ***
( Male )
MS 3470W 14- 15P
MIL - DTL - 26482
*** There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with
design flexibility possible. For more information, please contact us.
Input
Lockable
Connector
Part no.
DC Power
( Male )
YM-Ext-461CP001
USB
LUSB - A111 - 00
the
Standard
D-type 3W3
-
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
most
< 3.9 > Options : Quad Display
QD Specification
Item
Model Number
Description
QD (NTSC)
QD (PAL)
Number of Color
16.7 M
16.7 M
Imaging System
NTSC
PAL
1024 x 525
1024 x 625
60
50
Resolution
Refresh Rate
Video Input
Video Output
Camera Input
1.0 Vpp, 75 Ohm x 4
VCR Input
1.0 Vpp, 75 Ohm x 1
Live Monitor
1.0 Vpp, 75 Ohm x 1
Loop Through Out
1.0 Vpp, 75 Ohm x 4
VCR Output
1.0 Vpp, 75 Ohm x 1
Auto Gain Control
Yes
Time / Date
Yes
On Screen Display
Yes
Camera Title
Display Format
8 Character Title
2 x Zoom On
Playback
Yes
QUAD
Yes
FULL
Yes
SEQUENCY
Dw ell Time
Alarm Inputs
Relay Outputs
Yes
0 to 99 Sec Adjustable
Selectable NO/NC Contacts x 4
NO/NC contacts x 1: 1A @DC24V Max.
Alarm Hold Time
1 Sec to Non-stop
Built-in Buzzer
Yes
Key Lock
Yes
*** For QD option, casing dimensions will be changed.
< 3.10 > Options : TV ( Analog )
TV
Power BNC S-Video
Audio
VGA
HDMI
out - in - in
Video PC
***
For TV option :
( 1 ) The AD board comes standard with HDMI, VGA, S-Video, BNC, audio inputs and
RC-2 remote controller.
( 2 ) Casing dimensions will be changed.
How to Use RC-2 Remote Controller
1
8
2
INPU T
3
4
MUTE
1
2
3
4
5
6
7
8
9
AU TO
0
-/--
VOL
9
CH
10
FREEZE
11
12
5
SELECT
MENU
ASPECT
13
14
6
SLEEP
ENT ER
15
16
7
BACK
20
SO U RC E
SWAP
EXIT
PIP
POSI TION
PIP
AUDIO
17
18
PIP
21
19
r
1
INPUT
2
Select the source
Sw itches on or off the TV
Only use in TV mode. Select channels . For channel numbers 10
and above, enter the second digit w ithin two seconds.
Auto adjust
3
0-9
4
AUTO
5
MENU
6
▲ / ▼ / ◄ / ► / ENTER
7
BACK
Back to previous value
8
MUTE
Vol + / CH + / FREEZE
- / -ASPECT
SELECT
Turn on or off the speaker
SLEEP
EXIT
Select the sleeping time
9
10
11
12
13
14
15
16
Display the menu on the screen or go to the previous menu
Go to the upper menu or select the previous value /
Go to the next menu or select the next value /
Decrease the setting value /
Increase the setting value or enter to the select item setting
Enter to the select item settings or excude the setting
Increase or decrease the speaker volume
For TV model only , increase or decrease the channel number
Reserve for OEM model
For setting input single or double digits
Adjust the screen size
To select the exis ting item
Exit the menu or cancel
PIP functions
17
18
19
20
21
PIP
PIP AUDIO
POSITION
SOURCE
SWAP
Picture in picture
To set the audio of in PIP mode
To set the screen position in PIP mode
PIP Source
Swap screen in PIP mode
< 3.11 > Options : Auto Dimming
2
1
1
DA-01 Light sensor on OP model
2
DA-01 Light sensor on AP model
( 66cm from A D board to sensor end )
DA-01 light sensor will be installed on the display front panel when auto dimming is ON in OSD
menu. Then the brightness of display is changed according to its environmental brightness.
Once the auto dimming is ON, users cannot adjust brightness in OSD.
Steps : OSD Menu > Picture > Auto Dimming > ON
Light Sensor Operation Range
[cd/ m²]
[ v]
1,0 00
80 0
60 0
20 0
10
0
1
100
500
2,0 00
Options : Switch Dimming
DS-01 is a IP54 dimming knob installed on the display front panel. The display can support
hyper dimming function to adjust brightness from nearly 0% to 100% via a easy to use VR knob.
Dimming Knob
*** For
switch dimming option, casing dimensions will be changed.
[lx]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising