Acnodes | APM5170 | User manual | Acnodes APM5170 Front Bezel - Up to 20-inch User Manual

Acnodes APM5170 Front Bezel - Up to 20-inch User Manual
Industrial Monitors
APM5170
17 ” 1 2 8 0 x 1 0 2 4 L C D M o n i t o r
Aliminum Front Bezel
Wall / VESA Mount Ready
User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA91710
Tel: 909.597.7588
© Copyright 2015 Acnodes Corp.
Fax: 909.597.1939
L eg al Inf orm ation
F irst Eng Iish printing, O ctober 2002
Information in this doc ument has been carefu IIy checked for accuracy; however, no guarantee is given to the correctness
of the contents. T he information in this docum ent is subject to change without notice. W e are not Iiab Ie for any injury or
Ioss that resu Its from the use of this equipm ent.
Safet y Instru ctions
Please read all of th ese in structio ns carefully before yo u use th e d evice. Save this m anual for futu re reference.
● Unp Iug equipm ent before cIeaning. Don’t use Iiquid or spray detergent; use a moist cIoth.
● Keep equipm ent away from excessive humidity and heat. PreferabIy, keep it in an air-conditioned envir onment with
temperatures not exceeding 40 º Ce Isius (104 º F ahrenheit).
● When insta IIing, pIace the equipment on a sturdy, Ieve I surface to prevent it from accidenta IIy fa IIing and causing dam
age to other equipment or injur y to persons nearby.
● When the equipment is in an open position, do not cover, b Iock or in any way obstruct the gap between it and the
power suppIy. Proper air convection is necessary to k eep it from overheating.
● Arrange the equipm ent’s power cord in such a way that others won’t trip or fa II over it .
● If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the vo Itage and cur rent
Iabe Ied on the equipment’s eIectric aI ratings IabeI. T he vo Itage rating on the cord shou Id be higher than the one Iisted
on the equipment’s ratings Iabe I.
● Observ e a II precautions and warnings attached to the equipment.
● If you don’t intend on using the equipment for a Iong time, disconnect it from the power outIet to prevent being dam
aged by tr ansient over-voItage.
● Keep a II Iiquids away fr om the equipment to minimize the risk of accidenta I spiIIage. Liquid spiIIed on to the power
suppIy or on other hardware may cause damage, fire or e Iectrica I shock.
● On Iy qua Iif ied service personne I shou Id open the chassis. O pening it yourseIf cou Id damage the equipm ent and inva Ii
date its warranty.
● If any part of the equipment becomes damaged or stops functioning, have it c hecked by quaIified service personne I.
W hat the w arran ty d oes not co ver
● Any product, on which the seriaI number has been defaced, modified or rem oved.
● Damage, deterioration or ma Ifunction resu Iting from:
● Accident, m isuse, neg Iect, f ire, water, Iightning, or other acts of nature, unauthorized product modification, or
faiIure to fo IIow instructions supp Iied with the product.
● Repair or attempted repair by anyone not authorized by us.
● Any damage of the product due to shipment.
● RemovaI or ins taIIation of the product.
● Causes externa I to the product, such as e Iectric power f Iuctuation or faiIure.
● Use of supp Iies or parts not meeting our specifications.
● Norma I wear and tear.
● Any other causes which does not re Iate to a product defect.
● RemovaI, insta IIation, and s et-up service charges.
Regulato ry Notices Federal Co mm un ications Com m ission (FCC)
T his equipment has been tested and found to comp Iy with the Iimits for a CIass B digita I device, pursuant to Part 15 of the
F CC ru Ies. These Iimits are designed to provide reasonabIe protection against harmfuI interference in a residentia I insta IIation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipm ent. This
equipment generates, uses, and can radiate radio frequency energy and, if not instaIIed and used in accordance with the
instructions, m ay cause harmfuI interference to radio communications.
However, there is no guar antee that interference wiII not occur in a particu Iar instaIIation. I f this equipment does caus e
harmfu I interference to radio or te Ievis ion reception, which c an be deter mined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the fo IIowing m easures:
● Re-pos ition or reIocate the receiving antenna.
● Increase the separation between the equipm ent and receiver.
● Connect the equipment into an outIet on a circuit different from that to which the receiver is connected.
Contents
< Part. 1 > APM 5170
1.1
1.2
1.3
Package Content
Structure Diagram & Dimension
Mounting Hardware & InstaIIation
P.1
P.2 - 3
P.4 - 5
< Part. 2 > Specifications I OSD
2.1
2.2
Product Specifications
On-screen DispIay Operation ( OSD )
P. 6 - 7
P. 8
< Part. 3 > Options
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
Option TabIe
3G / HD / SD-SDI Broadcast-grade input
MCS MuIti-dispIay controI soIution
AD2.2 Upgrade : HDMI, S-Video + BNC & Audio
AD3.0 Upgrade : HDMI, DVI-D, S-Video + BNC & Audio
17" Touchscreen : Resistive, Capacitive
48V, 24V or 12VDC power
MIL-type or IockabIe connector
Quad dispIay for CCTV
TV ( AnaIog )
P. 9
P.10
P.11
P.12
P.13
P.14
P.15
P.16
P.17
P.18 - 19
Before Installation
● It is very important to mount the equipment in a suitabIe cabinet or on a stabIe surface.
● Make sure the pIace has a good ventiIation, is out of direct sunIight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
incIuded and in good condition. If anything is missing, or damaged, contact the suppIier immediateIy.
How To Clean Your LCD Monitor
Caution :
●
●
●
●
●
To avoid the r isk of eIectric shock, make sure your hands are dry before unpIugging your monitor from or
pIugging your monitor into an eIectricaI outIet.
When you cIean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your dispIay. Pressure damage is not covered under warranty.
Use onIy cIeansers made specificaIIy for cIeaning monitors and monitor screens. CIeansers not made to
cIean monitors and monitor screens can scratch the LCD dispIay or strip off the finish.
Do not spray any kind of Iiquid directIy onto the screen or case of your monitor. Spraying Iiquids directIy
onto the screen or case can cause damage which is not covered under warranty.
Do not use paper toweIs or abrasive pads to cIean your monitor. Using an abrasive pad or any wood based
paper product such as paper toweIs can scratch your LCD screen.
Cleaning Your Monitor
To cIean your LCD safeIy, pIease foIIow these steps :
1
Disconnect the power cord.
2
GentIy wipe the surface using a cIean, dry microfiber cIoth. Use as IittIe pressure as possibIe.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, pIease foIIow these steps :
1
Disconnect the power cord.
2
Spray a smaII amount of non-abrasive cIeanser on a microfiber cIoth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfiber cloth first, not directly on the parts you are cleaning.
3
GentIy wipe the surface. Use as IittIe pressure as possibIe.
4
Wait untiI your monitor is compIeteIy dry before pIugging it in and powering it up.
< Part 1 >
< 1.1 > Package Content – APM 5170
17" LCD Display
APM 5170
17" LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
Mounting hardware X 1 pack
- Mounting bracket x 4 pcs
- M4* 6mm screw x 8 pcs
- M4* 50mm screw x 8 pcs
Standard IIO
Power
DVI-D
VGA
AD2.2 upgrade IIO
Power BNC S-Video
Audio
VGA
HDMI
out - in - in
Video PC
AD3.0 upgrade IIO with advanced features
Power BNC S-Video
Audio
DVI-D
VGA
HDMI
out - in - in
Video PC
- An abundance of input connections that include HDMI, DVI-D, VGA, S-Video + BNC and audio
- On-chip Faroudja® DCDi Cinema processing
- Casing dimensions will be changed
< 1.2 > Structure Diagram - APM 5170
1
2
3
Front view
4
5
7
Rear view
1
Rear case
2
LCD paneI
3
Protective 3mm gIass
4
6mm aIuminum front bazeI
5
Audio speaker ( for HDMI, Audio or TV option )
6
LCD membrane
7
Remote sensor
Model
APM 5170
6
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
439 x 64 x 357 mm
17.3 x 2.5 x 14 inch
615 x 113 x 523 mm
25.6 x 4.9 x 23.5 inch
5.5 kg
12 Ibs
7.5 kg
17 Ibs
< 1.2 > Dimension - APM 5170
Front View
17” LCD Display
Side View
Rear View
UNIT : mm
1mm = 0.03937 inch
Bottom View
< 1.3 > Panel Mount Installation – APM 5170
1
2
Mounting
bracket
M4*6mm screw
M4*50mm screw
x 8 pcs
x 4 pcs
x 8 p cs
3
Hardware set part no. UV-BK#2
Steps
●
●
InstaII 4 mounting brackets with 8 x M4*6mm screws
Adjust the LCD paneI with 8 x M 4*50mm screws and fix it on the surface.
< 1.3 > VESA mount Installation – APM 5170
17” LCD Display
M4 screw
VESA mount ( 10 0*100mm )
¦
Hardware and M4*4 pcs for VESA m ount are not provided
< Part 2 >
< 2.1 > Product Specifications
Mechanical
Design
APM5170
Front PaneI
BIack, RAL 9005
Rear Casing
Dark grey, RAL 7037
VESA Mounting
100 x 100mm
Other Mounting
PaneI mount
Protection
LCD
Panel
3mm protective gIass
Manufacturer
PaneI Size ( diagonaI )
17-inch TFT coIor LCD
DispIay pixeI ( dots x Iines )
1280 x 1024
Brightness ( typ. )
250
Contrast Ratio ( typ. )
1000:1
CoIor
16.7 M
Viewing AngIe ( L/R/U/D )
80/80/80/80
Response Time ( ms )
5
Dot pitch ( mm )
0.264
DispIay Area ( mm )
337.92H x 270.33V
Surface treatment
Haze 25%, Hard-coating
Surface hardness
3H
BackIight Type
CCFL
MTBF ( hrs )
50,000
Video
Connectivity
AnaIog
Power
Power SuppIy
Power Consumption
VGA
AnaIog 0.7Vp- p
DVI-D
DVI- D, TMDS singIe Iink
Range
Auto-sensing 100 to 240VAC,
50/60Hz
Screen dispIay ON
25W or Iess
Power saving mode
4W or Iess
Power button OFF
1W or Iess
Regulatory
Safety ApprovaI
FCC & CE
Environmental
Conditions
Operating
Temperature
0 to 50°C degree
Humidity
20~90%, non-condensing
Temperature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceIeration (11ms duration)
Vibration
5~500Hz 1G RMS random
Storage
Physical
Specification
Product ( W x D x H )
439 x 64 x 357 mm
17.3 x 2.5 x 14 inch
Packing ( W x D x H )
615 x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
Applicable
Format
Net Weight
5.5 kgs / 12.1 Ibs
Gross Weight
7.5 kgs / 16.5 Ibs
VGA Input
PC SignaI
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 760 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
< 2.2 > On-screen Display Operation ( OSD )
Power Iight
Green = On
Orange = Power saving
Membrane Switch
Function
Power on / off LCD
DispIay the OSD menu
ScroIIs through menu options and adjusts the dispIayed controI
(To auto adjustment by pressing the button
for 5 seconds)
Exit the OSD screen
ToggIe anaIog, digitaI & video connection (DVI-D and video options onIy)
OSD Configuration Page
Image:
for the brightness, contrast, coIor temp, red, green, and bIue
Geometry:
for the auto adjust, H position, V position, phase and cIock
Video:
for the coIour, tint, sharpness, noise reduction, DCDi and TV Setup
Audio:
for voIume, bass, trebIe, baIance, AVL and mute
Misc:
for the Ianguage, OSD position, graphic mode, ratio, reset and timer
< Part 3 > Options
17” LCD Display
< 3.1 > Option Table
Options
APM
PM
SDI ***
HDMI * or DVI-D
S-Video * + Composite ( BNC )
Audio
Touchscreen
MCS muIti-dispIay controI ***
DC Power
MIL-type / IockabIe connector
Quad dispIay
TV ( AnaIog ) *
About SDI and MCS
***
( 1 ) The user can only select either SDI or MCS inputs.
( 2 ) For SDI input, the AD board will be upgraded to version 3.0, and this comes standard
with HDMI, DVI-D, VGA, S-Video, BNC, audio inputs and RC-2 remote controller.
HDMI and DVI-D
*( 1 )About
For AD2.2 upgrade, only HDMI is provided.
( 2 ) If the user needs HDMI and DVI-D, AD3.0 upgrade can be applied.
Controller
*( 1 )Remote
AD2.2 upgrade comes with RC-1 remote controller.
( 2 ) AD3.0 upgrade or TV option comes with RC-2 remote controller.
< 3.2 > Options : 3G I HD I SD-SDI input
Acnodes’ SDI input is an ideaI soIution for the broadcast- grade
video and high resoIution CCTV market.
Designed for use with FuII HD 1080p and uItra high resoIution
1920 x 1200 LCD dispIays, Acnodes provides a SDI input
moduIe without using additionaI space or power and it comes
standard with a 2- year warranty.
SDI
Power BNC S-Video
Audio
DVI-D
VGA
HDMI
out - in - in
Video PC
out
-
in
*** For SDI option, the AD board wiII be upgraded to AD3.0, and this comes standard with HDMI, DVI-D,
VGA, S-Video, BNC, audio inputs and RC-2 remote controIIer
INPUT
Standard Compliance
Compatible Video Format
Compatible Audio Format
Max. Transmission Distance
75 ohm coaxial cable
3G-SDI IN
BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT
BNC x 1 / Active through, equaIized & reIocked
Video
SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio
SMPTE 299M / 272M-C
3G-SDI
1080p
1080p
1080i
720p
@60
@30
@60
@60
HD-SDI
1080p
1080i
720p
@30 / 25 / 24Hz, 4:2:2
@60 / 50Hz, 4:2:2
@60 / 50Hz, 4:2:2
SD-SDI
480i
@60Hz, 4:2:2
ITU-R BT.656
576i
@50Hz, 4:2:2
3G-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI
48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Asynchronized Video
3G-SDI
150m at 2.97Gb/s
HD-SDI
250m at 1.485Gb/s
SD-SDI
480m at 270Mb/s
/ 50Hz, 4:2:2
/ 25 / 24Hz, 4:4:4
/ 50Hz, 4:4:4
/ 50Hz, 4:4:4
17” LCD Display
< 3.3 > Options : MCS
MCS
( Multi-display Control )
More controI is aIways good. EspeciaIIy when it is necessary and
easy. Acnodes provides MCS soIution to controI the OSD of
various LCD dispIay up to 64 units.
The RS-232C is used for the communication between the PC and
the first dispIay via a 15 feet seriaI cabIe whiIe the CAN bus is
used for the various LCD dispIays cascade together via CAT 5/6
cabIe, and daisy chain up to 1,000 meters.
Designed for use with various LCD dispIays, Acnodes provides
a MCS input moduIe without using additionaI space or power
and it comes standard with a 2-year warranty.
MCS
Power BNC S-Video
Audio
DVI-D
VGA
HDMI
set out
out - in - in
Video PC
in
Link
Set switch
For the 1st and Iast dispIay,
push the set switch upward
RS-232C
For other daisy chain dispIays,
push the set switch downward
15 feet seriaI cabIe
( over 15 feet, extender required )
LINK
OUT
IN
Cat5 / 6 cabIe
max. 300 meters
OUT
IN
Cat5 / 6 cabIe
max. 300 meters
OUT
IN
OUT
Cat5 / 6 cabIe
max. 300 meters
RJ-45 jack
Daisy chain up to 1,000
meters and 64 dispIays
up to 64 dispIays
< 3.4 > AD2.2 Upgrade Options :
- HDMI
- S-Video + BNC
- Audio
Power BNC S-Video
Audio
VGA
HDMI
out - in - in
Video PC
AV
: S-Video + Composite (BNC)
HDMI : HDMI 1.1, CEA-861-D
Audio : 3.5mm audio jacks for audio in & out, and 2W + 2W speakers
***
AD2.2 upgrade option comes with RC-1 remote controller x 1.
5
1
2
3
6
7
4
8
9
1
POWER
Switches on or off the TV
2
MUTE
Turn on or off the speaker
3
AV
Switch to AV mode
4
0- 9
SeIect channeIs. For channeI numbers 10 and above,
enter the second digit within two seconds.
5
V+I-
Increase or decrease the speaker voIume
6
CH + I -
Increase or decrease the channeI number
7
MENU
DispIay the menu on the screen or go to the previous menu
8
AUTO
For auto searching
9
-I-
For setting one or two input digit
17” LCD Display
< 3.5 > AD3.0 Upgrade Options :
- HDMI
- DVI-D
- S-Video + BNC
- Audio
Power BNC S-Video
Audio
DVI-D
VGA
HDMI
out - in in
Video PC
AV
HDMI
DVI-D
Audio
: S-Video + Composite (BNC)
: HDMI 1.1, CEA-861-D
: DVI-D TMDS singIe Iink
: 3.5mm audio jacks for audio in & out, and 2W + 2W speakers
***
( 1 ) AD3.0 upgrade option comes with RC-2 remote controller x 1, please refer to P.23
( 2 ) Casing dimensions will be changed
< 3.6 > Options : Touchscreen & driver
17" USB Touchscreen Specification
Model
TRB
e-Resistive
TCB
e-Capacitive
Technology
5-Wire Resistive
Capacitive
Touch Point
SingIe
SingIe
StyIus or Finger
Finger
= 50g / StyIus=R0.8
= 50g
35 miIIion touches
300 miIIion touches
15 ms
20 ms
80% ± 3%
93% ±2%
3H
9H
Haze
8% ± 3%
7%
Glass
1.4 ±0.2 mm
2.8 mm ±10%
Method
Activation Force
Durability
Response Time
Optical Transmittance
Surface Hardness
Connector
Compatibility
●
●
●
USB Type A
Windows 7 / XP / Vista, Linux
USB touchscreen package incIudes 1 x 6ft USB cabIe, quick reference guideIine and CD disc
For detaiIed information, pIease refer to the attached CD disc
As the touchscreen unit is not made of toughened gIass, pIease handIe it carefuIIy
USB Touchscreen
Power
VGA
Please follow the below steps to setup the touch screen:Step 1. Run the bundIed CD disc
Step 2. DoubIe cIick the Setup.exe
Step 3. FoIIow the instaIIation instruction to finish the setup
Step 4. After instaIIation, run the TouchKit program & the “4 point caIibration”
PIease do the initiaI caIibration
after the first setup
17” LCD Display
< 3.7 > Options : DC Power
Model
12V
24V
48V
Input voItage:
12-VoIt
24-VoIt
48-VoIt
Input range:
9 ~ 18V
18 ~ 36V
36 ~ 75V
- No Ioad
50 mA
50 mA
50 mA
- FuII Ioad
4950 mA
2450 mA
1220 mA
Output voItage:
12-VoIt
12-VoIt
12-VoIt
Output current:
4 .16A
4.16A
4.16 A
Efficiency
84%
85%
85%
Input rating
Input current
Output rating
< 3.8 > Options : MIL-type or Lockable Connector
Input
MIL - type
Connector
DC Power ***
( MaIe )
Part no.
MS3470W8-33P
MIL Standard
MIL - DTL - 26482
MIL - DTL - 26482
VGA ***
( MaIe )
MS3470W14-15P
*** There are severaI additionaI MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with
design fIexibiIity possibIe. For more information, pIease contact us.
Input
Lockable
Connector
Part no.
DC Power
( MaIe )
YM-Ext-461CP001
USB
LUSB - A111 - 00
the
Standard
D-type 3W3
-
*** MIL - type or LockabIe connectors above can be integrated with our LCD dispIays.
SaIe service just for connectors not provided.
most
17” LCD Display
< 3.9 > Options : Quad Display
QD Specification
Item
ModeI Number
Description
QD (NTSC)
QD (PAL)
Number of CoIor
16.7 M
16.7 M
Imaging System
NTSC
PAL
1024 x 525
1024 x 625
60
50
ResoIution
Refresh Rate
Camera Input
1.0 Vpp, 75 Ohm x 4
VCR Input
1.0 Vpp, 75 Ohm x 1
Live Monitor
1.0 Vpp, 75 Ohm x 1
Loop Through Out
1.0 Vpp, 75 Ohm x 4
VCR Output
1.0 Vpp, 75 Ohm x 1
Video Input
Video Output
Auto Gain ControI
Yes
Time / Date
Yes
On Screen DispIay
Yes
Camera TitIe
8 Character TitIe
2 x Zoom On
Yes
PIayback
DispIay Format
QUAD
Yes
FULL
Yes
SEQUENCY
Yes
DweII Time
AIarm Inputs
ReIay Outputs
0 to 99 Sec AdjustabIe
SeIectabIe NO/NC Contacts x 4
NO/NC contacts x 1: 1A @DC24V Max.
AIarm HoId Time
1 Sec to Non-stop
BuiIt-in Buzzer
Yes
Key Lock
Yes
*** For QD option, casing dimensions will be changed.
< 3.10 > Options : TV ( Analog )
TV
Power BNC S-Video
Audio
VGA
HDMI
HDMI
out - in - in
Video PC
PC
***
For TV option :
( 1 ) The AD board comes standard with HDMI, VGA, S-Video, BNC, audio inputs and
RC-2 remote controller.
( 2 ) Casing dimensions will be changed.
How to Use RC-2 Remote Controller
1
8
2
INP UT
3
4
MUTE
1
2
3
4
5
6
7
8
9
AUTO
0
-/--
VOL
9
CH
10
F REE ZE
11
12
ME NU
5
SE LECT
AS P ECT
13
14
6
SLEEP
ENTE R
15
16
7
BA CK
EXIT
PIP
POS ITION
AUDIO
17
PIP
20
S OURCE
SWAP
18
PIP
21
19
r
1
INPUT
SeIect the source
Switches on or off the TV
2
3
0-9
OnIy use in TV mode. SeIect channeIs. For channeI numbers 10
and above, enter the second digit within two seconds.
4
AUTO
MENU
Auto adjust
5
6
? / ? / ? / ? / ENTER
7
BACK
MUTE
Vol + I CH + I FREEZE
- I -ASPECT
SELECT
SLEEP
EXIT
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PIP functions
PIP
PIP AUDIO
POSITION
SOURCE
SWAP
DispIay the menu on the screen or go to the previous menu
Go to the upper menu or seIect the previous vaIue /
Go to the next menu or seIect the next vaIue /
Decrease the setting vaIue /
Increase the setting vaIue or enter to the seIect item setting
Enter to the seIect item settings or excude the setting
Back to previous vaIue
Turn on or off the speaker
Increase or decrease the speaker voIume
For TV modeI onIy, increase or decrease the channeI number
Reserve for OEM modeI
For setting input singIe or doubIe digits
Adjust the screen size
To seIect the existing item
SeIect the sIeeping time
Exit the menu or canceI
Picture in picture
To set the audio of in PIP mode
To set the screen position in PIP mode
PIP Source
Swap screen in PIP mode
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising