All rights reserved. Product description and product specifications are subject to change without notice. For lastest product information, please v is it Acnodes’ website at www.acnodes.com 14628 Central Ave. Chino, CA 91710 Tel: 909. 597. 7588 Fax: 909. 597. 1939 Legal Information First English printing, October 2002 Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from the use of this equipment. Safety Instructions Please read all of these instructions carefully before you use the device. Save this manual for future reference. ■ Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth. ■ Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with temperatures not exceeding 40º Celsius (104º Fahrenheit). ■ When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing damage to other equipment or injury to persons nearby. ■ When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the power supply. Proper air convection is necessary to keep it from overheating. ■ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it. ■ If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed on the equipment’s ratings label. ■ Observe all precautions and warnings attached to the equipment. ■ If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being damaged by transient over-voltage. ■ Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power supply or on other hardware may cause damage, fire or electrical shock. ■ Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and invalidate its warranty. ■ If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel. What the warranty does not cover ■ Any product, on which the serial number has been defaced, modified or removed. ■ Damage, deterioration or malfunction resulting from: □ Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. □ Repair or attempted repair by anyone not authorized by us. □ Any damage of the product due to shipment. □ Removal or installation of the product. □ Causes external to the product, such as electric power fluctuation or failure. □ Use of supplies or parts not meeting our specifications. □ Normal wear and tear. □ Any other causes which does not relate to a product defect. ■ Removal, installation, and set-up service charges. Regulatory Notices Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ■ Re-position or relocate the receiving antenna. ■ Increase the separation between the equipment and receiver. ■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Contents < Part. 1 > MKD6217U 1.1 1.2 1.3 Package Content Structure Diagram & Dimension Installation P.1 P.1 - 2 P.3 - 5 < Part. 2 > Specifications / OSD 2.1 2.2 2.3 2.4 Product Specifications Keyboard / Mouse Specifications On-screen Display Operation ( OSD ) Picture In Picture ( PIP ) / Picture By Picture ( PBP ) P.6 - 7 P.8 - 10 P.11 - 12 P.13 - 14 < Part. 3 > Options 3.1 3.2 P.15 P.15 Audio 48V, 24V or 12VDC power < Part. 4 > KVM Integration htt p:// www. acnodes.com/files/downloads/USBKVM-UM.pdf USB Hub DB-15 KVM Local Remote IP 8-port 16-port 1 0 1 KPH802 KPH1602 1 1 0 KVS802 KVS1602 1 0 0 KVH801 KVH1601 Before Installation ■ It is very important to mount the equipment in a suitable cabinet or on a stable surface. ■ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive dust, dirt, heat, water, moisture and vibration. Unpacking The equipment comes with the standard parts shown in package content. Check and make sure they are included and in good condition. If anything is missing, or damaged, contact the supplier immediately. How To Clean Your LCD Monitor Caution : ■ ■ ■ ■ ■ To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or plugging your monitor into an electrical outlet. When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can scratch or damage your display. Pressure damage is not covered under warranty. Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to clean monitors and monitor screens can scratch the LCD display or strip off the finish. Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly onto the screen or case can cause damage which is not covered under warranty. Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based paper product such as paper towels can scratch your LCD screen. Cleaning Your Monitor To clean your LCD safely, pleas e follow these steps : 1 Dis connect the power cord. 2 Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible. Cleaning Tough Marks and Smudges To rem ove tough m arks and smudges, please follow these steps : 1 Disconnect the power cord. 2 Spray a small amount of non-abrasive cleanser on a microfiber cloth. Cauti on : Do not spra y or apply any liquids directl y onto the monitor. Always apply the solution to your microfiber cloth first, not directly on the parts you are cleaning. 3 Gently wipe the surface. Use as little pressure as possible. 4 Wait until your monitor is com pletely dry before plugging it in and powering it up. < Part 1 > < 1.1 > Package Content MKD6217U unit X 1 - 6ft DVI-D co nsole cable X 1 - Power cord X 1 - M6 screw, cage nut & cup was her X 8 < 1.2 > Structure Diagram 5 1 6 7 2 8 3 9 10 4 1 LCD interchangeable module kit 6 Keyb oard interchangeable mod ule kit 2 Installation Slid es 7 Mouse interchangeable module kit 3 LCD memb rane 8 Blue Power LED 4 Membra ne switch (KVM option) 9 Front USB port for device access ( USB Hub KVM only ) 5 Micro switch for screen auto power off 10 Molded front handle < 1.2 > Dimension Front View UNIT : mm Sid e View 1mm = 0.03937 inch Top View Model MKD6217U Product Dimension (W x D x H) Packing Dimension (W x D x H) Net Weight Gross Weight 441.6 x 580 x 44 mm 17.4 x 22.84 x 1.73" 590 x 823 x 140 mm 23.2 x 32.4 x 5.5” 15 kg 33 lb 19 kg 42 lb < 1.3 > Installation - How to install Installation Slides Step ¦ Insert the left and right rear mounting brackets into the LCD c onsole drawer. Step ¦ ¦ 1 2 Measure the depth of the front and rear mounting rails. Align each rear mounting bracket to a suitable length. Step 3 Complete the installation ¦ Fix the LCD console drawer into the rack . M6 screw, cage nut & cup washer x 8 are provided. < 1.3 > Installation - How to install 2 post rack brackets Step 1 ¦ Release front mounting ears before applying 2 post r ac k brackets. ¦ Insert rear m ounting brack ets into the LCD console drawer. Opt ion Model : MB-751-12 Step ¦ 2 Align each rear mounting bracket to a suitable length. Rear mounting Front mounting Step 3 Complete the installation ¦ Fix the LCD cons ole drawer into the 2 post r ack. M6 screw, cage nut & cup washer x 8 are not provided. < 1.3 > Installation- How to use the drawer ¦ Hold the handle and slide out the drawer. ¦ Flip up the LCD to a suitable angle. ¦ Operate the LCD cons ole drawer. < Part 2 > < 2.1 > Product Specifications LCD Panel Panel Size ( diagonal ) 17.1-inch W idescreen TFT color LCD Display pixel ( dots x lines ) Brightness ( typ. ) 1920 x 1200 210 Contrast Ratio ( typ. ) 600:1 Color 16.7 M, 8-bit Viewing Angle ( L/R/U/D ) 65/65/55/55 Response Time ( ms ) 30 Dot pitc h ( mm ) 0.191 Display Area ( mm ) 367.20H x 229.50V Surface treatm ent Anti-glare, Har d-coating Surface hardness 3H Back light Type LED MTBF ( hrs ) 20,000 Video Connectivity Analog VGA Analog 0.7Vp-p Power Power Supply Range Auto-sens ing 100 to 240VAC, 50 / 60Hz Power Consumption Screen display ON 34W or less Power saving mode 4W or less Power button OFF 1W or less Regulatory Safety Approval FCC & CE Environmental Conditions Operating Temperature 0 to 50°C degree Humidity 20~90%, non-condensing Temperature -5 to 60°C degree Humidity 5~90%, non-condensing Shock 10G acceleration (11ms duration) Vibration 5~500Hz 1G RMS random Storage Physical Specification Product ( W x D x H ) 441.6 x 580 x 44 mm 17.4 x 22.84 x 1.73 inch Packing ( W x D x H ) 590 x 823 x 140 mm 23.2 x 32.4 x 5.5 inch Applicable Format Net Weight 15 kgs / 33 lbs Gross W eight 19 kgs / 42 lbs DVI-D / VGA Input PC Signal 1920 x 1200 x 60Hz 1920 x 1080 x 60Hz 1280 x 1024 x 60 / 75Hz 1280 x 960 x 60Hz 1280 x 768 x 60 / 75Hz 1152 x 864 x 75Hz 1024 x 768 x 60 / 70 / 75Hz 848 x 480 x 60Hz 800 x 600 x 60 / 72 / 75Hz 720 x 400 x 70Hz 640 x 480 x 60 / 72 / 75Hz 640 x 400 x 70Hz 640 x 350 x 70Hz HDMI Input PC Signal Same as VGA Video Signal 1080p : 60Hz Audio Signal 720p : 50 / 60Hz 480p : 60Hz 576p : 50Hz 2ch Linear PCM ( 32 / 44.1 / 48 KHz ) < 2.2 > Keyboard / Mouse Specifications Ge Gb G keyboard integrated with touchpad Key force 55 ± 5g Travelling distance 3 ± 0.3m m Switch life Soft ware support > 10 million life cycle time G keyboard integrated with tr ackball MS W indows 7 / 2008 / 2003 / 2000 / XP / ME / 98 / DOC Linux / Mac Supporting layouts America United States United Kingdom Germany France Spain Norway Italy Russia Switzerland Netherlands Portugal China Japan Korea Arabia Turkey EMEA Asia < 2.2 > MAC Keyboard / Mouse Options Me MAC keyboard integrated with touchpad F7 F8 Mb MAC keyboard integrated with track ball F7 F8 Supporting layouts America United States How to Use "MAC" Keyboard Keyboa rd Features F1 F9 Decrease display brightness Fast-forward F2 F10 Increase display brightness Mute sound F3 Missio n control * Only works with OS X Lion default Keyboard Shortcuts. F11 Decrease volume F4 F12 Dashboard Increase volume F7 Rewind Eject disc F8 Play / Pause Command < 2.2 > SUN Keyboard / Mouse Options Se Sb S keyboard integrated with touchpad N um C ap s S cr o l S keyboard integrated with trackball C om p ose Nu m S keyboard integrated with touchpad / trackball ¦ ¦ ¦ ¦ Incorporates SUN keys , inc luding Stop, Cut, Paste, Compose, Copy and Help 104 key notepad keyboard with full numerical pad and SUN function USB interface US layout only How to Use "S" Keyboard Num LED in Off mode Num LED in Green mode Key pad behaves as a SUN Solar system administration command mode Key pad behaves as a normal k ey pad mode Audio / Display K eys * P lease ask your supplier for full details F9 F11 Audio : Mute Display : Degauss Audio : Decrease volume Display : Decrease contrast F12 Audio : Increase volume Display : Increase contrast C a ps Sc ro l l Co mp os e < 2.3 > On-screen Display Operation ( OSD ) M embrane Switch Funct ion Turn the monitor on or off Display the OSD menu Act as an Enter key to select screen setting options Scroll through menu options and adjust the displayed co ntrol Exit t he OSD screen Go back to the previous on-screen sub-men u o r main menu Remark : All LED touch buttons in WHITE light. The LED of Power tou ch button will flash continuously when there is no signal input. 1 1 All the LED touch buttons will au tom atically turn off after 10 minutes of idle status ( excep t the Power 2 Light up all membran e bu tton s, please press any button for 1 - 2 seconds ( excep t the Power Pictu re Picture mode : Standard / Vivid / Soft / User mode to choose Brightness : Adjust background black level of the screen imag e Contrast : Adjust the difference between the image background (black level) an d the foreground (white level) Hue: Adjust the screen hue value Saturation : Adjust the saturation of the ima ge colo r Picture size : Adjust the image size Color temp : Standard / Cool / Warm / User to choose Noise red uce : Red uce the noise of the image Sharpness : Adjust the image from wea k to sha rp ). ). < 2.3 > On-screen Display Operation ( OSD ) 2 3 PC Auto adjust : Auto mat ically ad just sizes, centers and fine tunes the video signal to eliminate waviness and distortion. Clock : Adjust the clock value Phase : Adjust the phase value H. Po sition : Align the screen image left or right V. Position : Align the screen image up or down Audio Audio mode : Movie / Voice / Norm al / Music mode to choose Volum e : Adjust the volu me of sou nd Bass : Set the value of bass sound Treble : Set the value of treble sound Balance : Set the balance value of treble a nd bass sound Analog TV audio : Set the value of analog TV audio sound Mute : 4 Turn off the surrounding sound MISC Language : Sleep timer : Select the language in which the OSD menu is displaye d - English PIP mode : Set the off time Adjust picture in pict ure sett ing PIP position : Enter into PIP position PIP source : Enter into the Sub source and sound so urce System reset : Return the adjustment back to factory setting Information : Select for Help < 2.4 > How to Use Picture In Picture ( PIP ) / Picture By Picture ( PBP ) < 2.4.1 > Picture in Picture ( PIP ) Mode Display the Sub s creen in the M ain screen. OSD M enu > MISC > PIP Mode > Large / Small / OFF Main screen Sub screen Positi on Adjust the position of the Sub s creen ( top left, bottom left, top right, bottom right ) OSD M enu > MISC > PIP Position > top left / top right / bottom left / bottom right top left top right bottom left bottom right Size Adjust the size of the Sub s creen ( Large / Small ) OSD M enu > MISC > PIP Mode > Large / Small Size of Sub screen LCD Monitor Large Sub screen Small Sub screen 1920 x 1200 552 x 414 480 x 360 1920 x 1080 1440 x 900 552 x 414 414 x 310 480 x 360 360 x 270 1366 x 768 392 x 294 340 x 254 1280 x 1024 368 x 276 320 x 240 < 2.4.2 > Picture By Picture ( PBP ) Mode Display the Sub screen next to the Main screen. OSD Menu > MISC > PIP Mode > PBP Main scree n Sub s creen Size LCD Monitor Main / Sub screen 1920 x 1200 1920 x 1080 1440 x 900 955 x 716 955 x 716 715 x 536 1366 x 768 678 x 508 1280 x 1024 635 x 476 < Part 3> <3.1 > Options : - Audio ( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers ) < 3.2 > Options : DC Power Model 12V 24V 48V Input rating Input voltage: 12-Volt 24-Volt 48-Volt Input range: 9 ~ 18V 18 ~ 36V 36 ~ 75V - No load 50 mA 50 mA 50 mA - Full load 4950 mA 2450 mA 1220 mA Out put voltage : 12-Volt 12-Volt 12-Volt Out put current: 4.16 A 4.1 6A 4.16A Effi ciency 84% 85 % 85% Input current Output rating *** For DC power option : ( 1 ) Option excludes 1 x power cord and 1 x AC power adapt er.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project