Acnodes | MKDH8170C | User manual | Acnodes MKDH8170C High Brightness - LCD Drawer User Manual

Acnodes MKDH8170C High Brightness - LCD Drawer User Manual
All rights reserved. Product description and product specifications are subject to change without notice.
For lastest product information, please v is it Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA 91710
Tel: 909. 597. 7588
© C opyright 2015 Acnodes C orp.
Fax: 909. 597. 1939
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the
contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from
the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
■ Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■ Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■ When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
■ When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■ If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■ Observe all precautions and warnings attached to the equipment.
■ If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
■ Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.
■ Only qualified service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
■ If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
What the warranty does not cover
■ Any product, on which the serial number has been defaced, modified or removed.
■ Damage, deterioration or malfunction resulting from:
□ Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or
failure to follow instructions supplied with the product.
□ Repair or attempted repair by anyone not authorized by us.
□ Any damage of the product due to shipment.
□ Removal or installation of the product.
□ Causes external to the product, such as electric power fluctuation or failure.
□ Use of supplies or parts not meeting our specifications.
□ Normal wear and tear.
□ Any other causes which does not relate to a product defect.
■ Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
■ Re-position or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Contents
< Part. 2 > MKDH8170C/8190C
1.1
1.2
1.3
Package Content
Structure Diagram & Dimension
Installation
P.1
P.1 - 2
P.3 - 5
< Part. 2 > Specifications / OSD
2.1
2.2
2.3
Product Specifications
Keyboard / Mouse Specifications
On-screen Display Operation ( OSD )
P.6 - 7
P.8
P.9 - 10
< Part. 3 > Options
3.1
3.2
P.11
P.12
Audio
48V, 24V or 12VDC power
< Part. 4 > KVM Integration
http://www.acnodes.com/files/downloads/CKVM-UM.pdf
Combo
Cat6 KVM
Local
Remote
IP
8-port
16-port
1
0
1
KCP802
KCP1602
1
1
0
KC802
KC1602
KC3202
1
0
0
KCS801
KC1601
KC3201
32-port
KCP3202
Before Installation
■ It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
■
■
■
■
■
To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.
Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
1
Disconnect the power cord.
2
Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1
Disconnect the power cord.
2
Spray a small amount of non-abrasive cleanser on a microfiber cloth.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the
solution to your microfiber cloth first, not directly on the parts you are cleaning.
3
Gently wipe the surface. Use as little pressure as possible.
4
Wait until your monitor is completely dry before plugging it in and powering it up.
< Part 1 >
< 1.1 > Package Content
MKDH 8170C/8190C unit X 1
- 6ft Combo KVM cable X 1
- Power cord X 1
- M6 screw, cage nut & cup wash er X 8
< 1.2 > Structure Diagram
5
1
6
7
2
8
3
9
10
4
1
LCD interchange able mo dule kit
6
Keyboard interchangeable module kit
2
Installation Slides
7
Mouse interchangeable m odule kit
3
LCD membrane
8
Blue Power LED
4
Membrane switch (KVM option)
9
Front USB port for device access ( US B Hub KVM only )
5
Micro switch for screen auto power off
10
Molded front handle
< 1.2 > Dimension
Fro nt View
UNIT : mm
Side View
1mm = 0 .039 37 inch
Top View
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
MKDH8170C
441.6 x 580 x 44 mm
17.4 x 22.8 x 1.73"
590 x 823 x 140 mm
23.2 x 32.4 x 5.5”
13 kg
29 lb
18.5 kg
41 lb
MKDH8190C
441.6 x 620 x 44 mm
17.4 x 24.4 x 1.73"
590 x 823 x 140 mm
23.2 x 32.4 x 5.5”
14 kg
31 lb
19.5 kg
43 lb
< 1.3 > Installation - How to install Installation Slides
Step
¦
Insert the left and right rear mounting brackets into
the LCD c onsole drawer.
Step
¦
¦
1
2
Measure the depth of the front and rear mounting rails.
Align each rear mounting bracket to a suitable length.
Step
3
Complete the installation
¦
Fix the LCD console drawer into the rack .
M6 screw, cage nut & cup washer x 8 are provided.
< 1.3 > Installation - How to install
2 post rack brackets
Step
1
¦
Release front mounting ears before applying 2 post
r ac k brackets.
¦
Insert rear m ounting brack ets into the LCD console
drawer.
Opt ion
Model : MB-751-12
Step
¦
2
Align each rear mounting bracket to a suitable length.
Rear mounting
Front mounting
Step
3
Complete the installation
¦
Fix the LCD cons ole drawer into the 2 post r ack.
M6 screw, cage nut & cup washer x 8
are not provided.
< 1.3 > Installation- How to use the drawer
¦
Hold the handle and slide out the
drawer.
¦
Flip up the LCD to a suitable angle.
¦
Operate the LCD cons ole drawer.
< Part 2 >
< 2.1 > Product Specifications
LCD
Panel
MKDH8170C
Panel Size ( diagonal )
MKDH8190C
17-inch TFT color LCD
19-inch TFT color LCD
1280 x 1024
1280 x 1024
1000
1000
Contras t Ratio ( typ. )
1000:1
1000:1
Color
16.7 M
16.7 M
85/85/80/80
80/80/80/80
5
5
0.264
0.294
337.92H x 270.33V
376.32H x 301.05V
Surface treatment
Anti-glare
Haze 25%, hard coating
Surface hardness
3H
3H
LED
LED
50,000
50,000
Display pix el ( dots x lines )
Brightness ( typ. )
Viewing Angle ( L/R/U/D )
Response Tim e ( ms )
Dot pitch ( mm )
Display Ar ea ( mm )
Backlight Type
MTBF ( hrs )
Video
Connectivity
Analog
VGA
Analog 0.7Vp-p
Power
Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consum ption
Screen display ON
35W or less
Power s aving m ode
4W or less
Power button OFF
1W or less
Environmental
Conditions
Operating
Storage
Tem perature
0 to 50°C degree
Humidity
20~90%, non-condensing
Tem perature
-5 to 60°C degree
Humidity
5~90%, non-condensing
Shock
10G acceleration (11ms duration)
Vibration
5~500Hz 1G RMS random
Regulatory
Physical
Specification
Safety Approval
MKDH8170C
Product ( W x D x H )
Packing ( W x D x H )
Net Weight
Gross W eight
Applicable
Format
FCC & CE
VGA Input
MKDH8190C
441.6 x 580 x 44 m m
441.6 x 620 x 44 mm
17.4 x 22.8 x 1.73 inch
17.4 x 24.4 x 1.73 inch
590 x 823 x 140 mm
590 x 823 x 140 mm
23.2 x 32.4 x 5.5 inch
23.2 x 32.4 x 5.5 inch
13 k gs / 29 lbs
14 k gs / 31 lbs
18.5 k gs / 41 lbs
19.5 k gs / 43 lbs
PC Signal
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 760 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
< 2.2 > Keyboard / Mouse Specifications
Ge
Gb
G keyboard integrated with touchpad
Key force
55 ± 5g
Travelling distance
3 ± 0.3m m
Switch life
Soft ware support
> 10 million life cycle time
G keyboard integrated with tr ackball
MS W indows 7 / 2008 / 2003 / 2000 / XP / ME / 98 / DOC
Linux / Mac
Supporting layouts
America
United States
United Kingdom
Germany
France
Spain
Norway
Italy
Russia
Switzerland
Netherlands
Portugal
China
Japan
Korea
Arabia
Turkey
EMEA
Asia
< 2.3 > On-screen Display Operation ( OSD )
M embrane Switch
Funct ion
Turn the monitor on or off
Display the OSD menu
Act as an Enter key to select screen setting options
Scroll through menu options and adjust
the displayed co ntrol
Exit t he OSD screen
Go back to the previous on-screen sub-men u o r
main menu
Remark : All LED touch buttons in WHITE light.
The LED of Power
tou ch button will flash continuously when there is no signal input.
1
All the LED touch buttons will au tom atically turn off after 10 minutes of idle status ( excep t the Power
2
Light up all membran e bu tton s, please press any button for 1 - 2 seconds ( excep t the Power
).
).
< 2.3 > On-screen Display Operation ( OSD )
OSD C onfiguration Page
Image:
for the brightness, contrast, color temp , red, green, and blue
Geometry:
for the auto adjust, H position, V position, phase and clock
Video:
for the colour, tint, sharpness, noise reduction, DCDi and TV Setup
Audio:
for volume, bass, treble, balance, AV L and mute
Misc:
for the language, OSD position, graphic mode, ratio, reset and timer
< Part 3 >
< 3.1 > Options :
- Audio ( 3.5mm audio jack s for au dio in & o ut, and 2W + 2W spea kers )
< 3.2 > Options : DC Power
Model
24V
48V
24-Volt
48-Volt
18 ~ 36V
36 ~ 75V
- No load
50 m A
50 mA
- Full load
4880 mA
2442 mA
Output voltage:
12-Volt
12-Volt
Output current:
8.3A
8.3A
Efficiency
85%
86%
Input r ating
Input voltage:
Input ra nge :
Input current
Output rating
DC power
KVM
***
For DC power option :
( 1 ) Option excludes 1 x power cord and 1 x AC power adapter.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising