CyberData | 011233 | Owner Manual | Cyberdata 011233 SIP Paging Adapter Owner manual

Cyberdata 011233 SIP Paging Adapter Owner manual
Mounting
You have the option to use the following mounting template to mark, and then drill two 3/16-inch (0.1875-inch) holes for
the mounting anchors.
Installation Quick Reference
The IP Endpoint Company
To install and mount the SIP Paging Adapter:
SIP Paging Adapter
1. Install the mounting anchors in the holes, and position the SIP Paging Adapter mounting holes over the anchors.
SIP Compliant
2. Use the two #6 sheet metal screws to secure the SIP Paging Adapter onto the mounting surface.
011233
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Address
a
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
a
255.0.0.0
a
Default Gateway
10.0.0.1
a. Default if there is not a DHCP server present.
Getting Started
•
Be sure that you have received all the parts described in the Parts List section.
•
Download the Operations Guide at the following website:
http://www.cyberdata.net/voip/011233/
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Parts List
(1) SIP Paging Adapter
Drill Hole Size for Anchor Installation: 3/16-inch (0.1875-inch)
(1) Mounting Template
(see the last page)
(1) Mounting Kit
(2) #6 x1.25-inch, PanHead,
Phillips Sheet Metal Screw
Dimensions
(2) Plastic Anchors
Contacting CyberData
6.0 [152.4]
Corporate Headquarters
1.2 [29.6]
4.1 [104.0]
Dimensions are in Inches [Millimeters]
Dimensions are in Inches [Millimeter]
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
931084C
Quick Reference
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Quick Reference
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
931084C
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
Connections
Verifying Operations and Settings
Page Port Output Connections
When you plug in the Ethernet cable or power supply:
•
•
•
The GREEN/BLUE Status LED and the
GREEN Paging LED both blink at a rate of
10 times per second during the initial network
setup.
Link
(GREEN/AMBER LED)
Activity
(GREEN LED)
The round, GREEN/BLUE Status LED on the
front of the SIP Paging Adapter comes on
indicating that the power is on. Once the device
has been initialized, this LED blinks at one
second intervals.
The square, GREEN/AMBER Link LED above
the Ethernet port indicates that the network
connection has been established. The Link LED
changes color to confirm the auto-negotiated
connection speed:
•
The Link LED is GREEN at 10 Mbps.
•
The Link LED is AMBER at 100 Mbps.
•
The GREEN Paging LED comes on after the
device is booted and initialized. This LED
blinks when a page is in progress. You can
disable Beep on Initialization on the Device
Configuration page.
Description
1
Fault Sense Input (Common)
2
Fault Sense Input (Sense)
3
Positive 600-Ohm Audio Outputa
4
Negative 600-Ohm Audio Outputa
5
Audio Ground Reference
6
Relay Contact - Commonb
7
Relay Contact - Normally Openb
Status
(GREEN/BLUE LED)
Paging
(GREEN LED)
To set up the device, connect the device to your network:
Pag
•
ing
Ad
Pin 1 Pin2 Pin 3 Pin 4 Pin 5
48VDC
Pin 6
Pin 7
RTFM Switch
To announce the IP address:
To restore the factory default settings:
1. Briefly press and then quickly
release the RTFM switch.
1. Press and hold the RTFM switch while all the indicator
lights turn off.
2. Continue to press the switch until after the indicator lights
turn back on, and then release the switch.
Note: The “Restoring Defaults” announcement can be
heard if a speaker or amplified speaker is connected to the
unit.
3. All SIP Paging Adapter settings are restored to the
factory defaults, and the unit reboots.
Note: The IP address announcement
can be heard if a speaker or amplified
speaker is connected to the unit.
Poe
SIP
RCA Line Out Page Port Output Power
a. The 600-Ohm audio output of the
page port is also suited for interfaces
with lower input impedances.
b. 1 Amp at 30 VDC for continuous loads
Setting Up the SIP Paging Adapter
PoE
RCA Line In
Pin
ap
ter
For PoE, plug one end of an 802.3af Ethernet cable into
the SIP Paging Adapter Ethernet port. Plug the other
end of the Ethernet cable into your network. See the
figure on the left.
RTFM Switch
Typical Configuration
Non PoE with 48 VDC Power Supply
Non-Poe
•
For Non-PoE, connect the SIP Paging Adapter to a
48VDC power supply. See the figure on the left.
•
Note: Do not use both PoE and external power.
48VDC
Chassis Ground
Chassis Ground
•
If required, connect the earth grounding wire to the
Chassis Ground. See the figure on the left.
Chassis ground
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
931084C
Quick Reference
Quick Reference
931084C
© 2018, CyberData Corporation, ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising