CyberData | 011146 | Operations Guide | Cyberdata 011146 SIP Paging Server with Bell Scheduler Operations Guide

Cyberdata 011146 SIP Paging Server with Bell Scheduler Operations Guide
The IP Endpoint Company
SIP Paging Server
Operations Guide
SIP Compliant
Part #011146
Document Part #931073J
for Firmware Version 12.1.0
CyberData Corporation
3 Justin Court
Monterey, CA 93940
(831) 373-2601
Operations Guide 931073J
SIP Compliant 011146
COPYRIGHT NOTICE:
© 2017, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part of
this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or such
products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make
changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by third
parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by Cyberdata that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be
the trademarks or registered trademarks of their respective owners.
Technical Support 

The IP Endpoint Company The fastest way to get technical support for your VoIP product is to
submit a VoIP Technical Support form at the following website:
http://support.cyberdata.net/

Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Fax: (831) 373-4193
Company and product information is at www.cyberdata.net.
CyberData Corporation
931073J
Operations Guide
Revision Information
Revision 931073J, which corresponds to firmware version 12.1.0, was released on May 7, 2019, and
has the following changes:
•
Updates Figure 2-11, "Home Page"
•
Updates Figure 2-22, "Configure Scheduled Event Window"
•
Updates Table 2-15, "Configure Scheduled Event Window Parameters"
•
Updates Figure 2-33, "Home Page"
Browsers Supported
The following browsers have been tested against firmware version 12.1.0:
•
Internet Explorer (version: 11)
•
Firefox (also called Mozilla Firefox) (version: 62.0)
•
Chrome (version: 63.0.3239.132)
•
Safari (version: 12)
•
Microsoft Edge (version: 42.17134.1.0)
CyberData Corporation
931073J
Operations Guide
Pictorial Alert Icons
General Alert
This pictoral alert indicates a potentially hazardous situation. This alert will be
followed by a hazard level heading and more specific information about the
hazard.
GENERAL ALERT
Ground
This pictoral alert indicates the Earth grounding connection point.
Hazard Levels
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. This is limited to the most extreme situations.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. It may also alert users against unsafe practices.
Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).
The safety guidelines for the equipment in this manual do not purport to address all the safety issues
of the equipment. It is the responsibility of the user to establish appropriate safety, ergonomic, and
health practices and determine the applicability of regulatory limitations prior to use. Potential safety
hazards are identified in this manual through the use of words Danger, Warning, and Caution, the
specific hazard type, and pictorial alert icons.
CyberData Corporation
931073J
Operations Guide
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
13. Prior to installation, consult local building and electrical code requirements.
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached
to the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
CyberData Corporation
931073J
Operations Guide
Abbreviations and Terms
Abbreviation or Term
Definition
A-law
A standard companding algorithm, used in European digital
communications systems to optimize, i.e., modify, the dynamic range of an
analog signal for digitizing.
AVP
Audio Video Profile
Cat 5
TIA/EIA-568-B Category 5
DHCP
Dynamic Host Configuration Protocol
LAN
Local Area Network
LED
Light Emitting Diode
Mbps
Megabits per second.
NTP
Network Time Protocol
PBX
Private Branch Exchange
PoE
Power over Ethernet (as per IEEE 802.3af standard)
RTFM
Reset Test Function Management
SIP
Session Initiated Protocol
u-law
A companding algorithm, primarily used in the digital telecommunication
UC
Unified Communications
VoIP
Voice over Internet Protocol
CyberData Corporation
931073J
Operations Guide
i
Contents
Chapter 1 Product Overview
1
1.1 How to Identify This Product .....................................................................................................1
1.2 Product features .......................................................................................................................2
1.3 Product Specifications ..............................................................................................................3
1.4 Compliance ..............................................................................................................................4
1.4.1 Safety .............................................................................................................................4
1.4.2 FCC Statement ..............................................................................................................4
Chapter 2 Setting Up the SIP Paging Server
5
2.1 Parts List ..................................................................................................................................5
2.2 Typical Installation ....................................................................................................................6
2.3 Connecting the SIP Paging Server ...........................................................................................7
2.3.1 Ground Connection ........................................................................................................7
2.3.2 Line In ............................................................................................................................7
2.3.3 Line Out ..........................................................................................................................7
2.3.4 Page Port Output Connections .......................................................................................8
Pin 1 and 2—Fault Sense Input (Common/Sense) ..........................................................8
Pin 3, 4, and 5—Positive/Negative 600-Ohm Audio Output/Audio Ground Reference .....8
Pin 6 and 7—Relay Contact (Common/Normally Open) ..................................................8
2.3.5 Removable Interface Connector .....................................................................................9
2.3.6 Connect to the Power Source ......................................................................................10
Poe .................................................................................................................................10
Non-Poe .........................................................................................................................10
Chassis Ground ..............................................................................................................10
2.3.7 Connect to the Network ...............................................................................................11
2.3.8 Confirm that the SIP Paging Server is Up and Running ..............................................12
Confirm Power on, Network Connectivity, and Connection Speed ................................12
Verify Network Activity ...................................................................................................12
2.3.9 Announcing the IP Address ..........................................................................................13
2.3.10 Restore the Factory Default Settings .........................................................................13
2.4 Configuring the SIP Paging Server ........................................................................................14
2.4.1 Gather the Required Configuration Information ..........................................................14
Static or DHCP Addressing? .........................................................................................14
Username and Password for Configuration GUI ...........................................................14
SIP Settings ...................................................................................................................14
2.4.2 SIP Paging Server Web Page Navigation ....................................................................15
2.4.3 Using the Toggle Help Button .......................................................................................16
2.4.4 Log in to the Configuration GUI ...................................................................................18
2.4.5 Configure the Device Parameters ................................................................................22
Polycom Paging ..............................................................................................................24
Time Zone Strings ..........................................................................................................26
2.4.6 Configure the Network Parameters .............................................................................29
2.4.7 Configure the SIP Parameters .....................................................................................32
Point-to-Point Configuration ............................................................................................37
2.4.8 Configure the Paging Groups (PGROUPS) Parameters ..............................................38
2.4.9 Operating the Paging Server ........................................................................................44
DTMF Bypassed .............................................................................................................44
DTMF Not Bypassed ......................................................................................................44
2.4.10 Configure the Schedules Parameters ........................................................................45
2.4.11 Configure the Fault Detection Parameters .................................................................49
2.4.12 Configure the Audio Parameters ................................................................................51
CyberData Corporation
931073J
Operations Guide
ii
User-created Audio Files ................................................................................................54
2.4.13 Configure the Event Parameters ................................................................................57
Example Packets for Events ...........................................................................................59
2.4.14 Configure the Autoprovisioning Parameters ...............................................................62
Autoprovisioning .............................................................................................................64
Sample dhcpd.conf .........................................................................................................72
Get Autoprovisioning Template Button ...........................................................................73
2.5 Upgrading the Firmware .........................................................................................................74
2.5.1 Upgrade the Firmware ..................................................................................................74
2.5.2 Reboot the SIP Paging Server .....................................................................................76
2.6.1 Command Interface Post Commands ..........................................................................77
Appendix A Setting Up a TFTP Server
81
A.1 Set up a TFTP Server ............................................................................................................81
A.1.1 In a LINUX Environment ..............................................................................................81
A.1.2 In a Windows Environment .........................................................................................81
Appendix B Troubleshooting/Technical Support
82
B.1 Frequently Asked Questions (FAQ) ........................................................................................82
B.2 Documentation .......................................................................................................................82
B.3 Contact Information ................................................................................................................83
B.4 Warranty and RMA Information ..............................................................................................83
CyberData Corporation
931073J
Operations Guide
1
1 Product Overview
1.1 How to Identify This Product
To identify the SIP Paging Server, look for a model number label similar to the one shown in Figure
1-1. Confirm the following:
•
The model number on the label should be 011146.
•
The serial number on the label should begin with 1461.
Figure 1-1. Model Number Label1
www.cyberdata.net
SIP PAGING SERVER
011146* / 021508*
146100001
CAN ICES-3 (A)/NMB-3(A)
00:20:F7:03:83:CA
V12.1.0
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
Model number
Serial number begins with 1461
1. This figure is just an example. The information on your label may look different.
CyberData Corporation
931073J
Operations Guide
Product Overview 2
Product features
1.2 Product features
•
Up to 25 unique bell files that can be used in up to 250 scheduled events
•
Up to 25 stored messages that are utilized through paging groups
•
Can page directly to Polycom phones
•
Voice prompting and password controlled zones
•
SIP RFC 3261 compatible
•
NTP-based internal clock
•
Multicast output
•
Two SIP endpoints (one for Night Ringer)
•
DTMF control of zone selection
•
Delayed page support
•
Line-In connection for background music multicasting
•
Line-out connection to support analog amplifiers
•
User uploadable audio files
•
Web-based configuration and firmware upload
•
PoE 802.3af enabled (Power-over-Ethernet)
•
19-inch Rack mount option
CyberData Corporation
931073J
Operations Guide
Product Overview 3
Product Specifications
1.3 Product Specifications
Table 1-1. Product Specifications
Specifications
Protocol
SIP RFC 3261 Compatible
Ethernet I/F
10/100 Mbps
Power Input
PoE 802.3af or 48VDC
Operating Temperature
-10° C to 50° C (14° F to 122° F)
Payload Types
G711, A-law and µ-law, G.722
Page Port Output
Balanced 600 Ohm 5VPP
Line In:
Input Signal Amplitudes
2.0 VPP maximum
Input Impedance
10k Ohm
Line Out:
Output Signal Amplitudes
2.0 VPP maximum
Output Level
+2dBm nominal
Total Harmonic Distortion
0.5% maximum
Output Impedance
10k Ohm
Dimensions
a
6.11 inches [155.19 mm] Length
4.05 inches [102.87 mm] Width
1.15 inches [29.21 mm] Height
Boxed Weight
1.8 lbs.
Compliance
UL 62368-1, RoHS Compliant, FCC; Part 15 Class A, IEEE
802.3 Compliant; Reference Number for UL: E129569 Vol
4 Sec 1
Part Number
011146
a. Dimensions are measured from the perspective of the product being upright with
the front of the product facing you.
CyberData Corporation
931073J
Operations Guide
Product Overview 4
Compliance
1.4 Compliance
1.4.1 Safety
This product is listed by UL. Representative samples of this product have been evaluated by UL and
meet applicable safety standards. (Standard: UL 62368-1). This applies to the following products:
011145, 011146, 011233, 011280, 011295, 011368, 011372
Note
You can download the Declaration of Conformity document from the Downloads tab of the
product’s webpage.
1.4.2 FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
CyberData Corporation
931073J
Operations Guide
5
2 Setting Up the SIP Paging Server
The topics in this chapter provide information on setting up, configuring, and using the SIP Paging
Server.
2.1 Parts List
The packaging for the SIP Paging Server includes the parts in Table 2-1.
Table 2-1. Parts List
Quantity
Part Name
1
SIP Paging Server
1
Installation Quick Reference Guide
1
Mounting Template (located on the last
page of the Installation Quick
Reference)
1
Mounting Kit (part #070057A) 
which includes:
(2) #4-6 x 7/8" Mounting Anchors
(2) #4 x 1-1/4" Round Phillips Wood
Screws
CyberData Corporation
Illustration
931073J
Operations Guide
Setting Up the SIP Paging Server 6
2.2 Typical Installation
Figure 2-1 illustrates how the SIP Paging Server is normally installed as part of a paging system.
Figure 2-1. Typical Installation
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 7
Ground Connection
2.3 Connecting the SIP Paging Server
Before you connect the SIP Paging Server, be sure that you have received all of the parts described
in Section 2.1, "Parts List".
See Figure 2-2 for the connection options that are available for the SIP Paging Server.
Figure 2-2. Connection Options
Line In
Ground Connection
Line Out
Pin 1
Page Port Output Connections
Pin 2
Pin 3
Pin 4
Pin 5
Power
Pin 6
48VDC
Pin 7
2.3.1 Ground Connection
This connection allows you to connect the device to an electrical ground.
2.3.2 Line In
This RCA 10K Ohm Hi-Z input connection allows you to connect the device to The RCA line-out
(10K Ohm Hi-Z) of an external audio amplifier. The level of this input can be controlled by the
potentiometer located on the front of the device (see Section 2.4.11, "Configure the Fault Detection
Parameters").
2.3.3 Line Out
This RCA 10K Ohm Hi-Z output connection allows you to connect the device to The RCA line-in
(10K Ohm Hi-Z) of an external audio amplifier.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 8
Page Port Output Connections
2.3.4 Page Port Output Connections
Table 2-1. Page Port Output Connections
Pin
Description
Pin 1
Fault Sense Input (Common). See Section 2.3.4.1, "Pin 1 and 2—Fault Sense Input (Common/Sense)".
Pin 2
Fault Sense Input (Sense). See Section 2.3.4.1, "Pin 1 and 2—Fault Sense Input (Common/Sense)".
Pin 3
Positive 600-Ohm Audio Outputa. See Section 2.3.4.2, "Pin 3, 4, and 5—Positive/Negative 600-Ohm Audio
Output/Audio Ground Reference".
Pin 4
Negative 600-Ohm Audio Output.a. See Section 2.3.4.2, "Pin 3, 4, and 5—Positive/Negative 600-Ohm Audio
Output/Audio Ground Reference".
Pin 5
Audio Ground Reference. See Section 2.3.4.2, "Pin 3, 4, and 5—Positive/Negative 600-Ohm Audio Output/Audio
Ground Reference".
Pin 6
Relay Contact - Commonb. See Section 2.3.4.3, "Pin 6 and 7—Relay Contact (Common/Normally Open)".
Pin 7
Relay Contact - Normally Openb. See Section 2.3.4.3, "Pin 6 and 7—Relay Contact (Common/Normally Open)".
a. The 600-Ohm audio output of the page port is also suited for interfaces with lower input impedances.
b. 1 Amp at 30 VDC for continuous loads
2.3.4.1 Pin 1 and 2—Fault Sense Input (Common/Sense)
This input was designed as a method of monitoring an external amplifier that is equipped with a fault
sense relay.
When enabled via the web interface (Section 2.4.11, "Configure the Fault Detection Parameters"),
this input (when closed) will play a user uploadable audio file out of the line-out connection and/or
place a SIP call to a pre-determined extension and play that file.
2.3.4.2 Pin 3, 4, and 5—Positive/Negative 600-Ohm Audio Output/Audio Ground
Reference
This output allows direct connection to paging amplifiers requiring a "Page Port" type input that
meets a balanced 600 Ohm 5VPP signal.
2.3.4.3 Pin 6 and 7—Relay Contact (Common/Normally Open)
When enabled on the web interface (Section 2.4.5, "Configure the Device Parameters"), every time
an audio file is played out of the local line-out or 600 Ohm output, the relay will close, thereby
enabling amplifiers with a remote turn-on capability to become active.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 9
Removable Interface Connector
2.3.5 Removable Interface Connector
Figure 2-3 shows the interface connector that is removable on the SIP Paging Server.
Figure 2-3. Removable Interface Connector
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 10
Connect to the Power Source
2.3.6 Connect to the Power Source
To use PoE, plug a Cat 5 Ethernet cable from the SIP Paging Server Ethernet port to your network.
As an alternative to PoE, you can plug one end of a +48V DC power supply into the Paging Server,
and plug the other end into a receptacle. If required, connect the earth grounding wire to the chassis
ground on the back of the unit. See Figure 2-4.
Figure 2-4. Connecting to the Power Source
To set up the SIP Paging Server, connect the
device to your network:
PoE
Poe
•
For PoE, plug one end of an 802.3af
Ethernet cable into the SIP Paging Server
Ethernet port. Plug the other end of the
Ethernet cable into your network. See the
figure on the left.
Non PoE (with 48 VDC power supply)
Non-Poe
Chassis Ground
•
For Non-PoE, connect the SIP Paging
Server to a 48VDC power supply. See the
figure on the left.
•
Note: Do not use both PoE and external
power.
•
Alternatively, you can use our 
part# 010867 PoE Power Injector 
as a cost-effective option.
Chassis Ground
•
If required, connect the earth grounding wire
to the Chassis Ground. See the figure on
the left.
Chassis Ground
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 11
Connect to the Network
2.3.7 Connect to the Network
Plug one end of a standard Ethernet cable into the Paging Server Ethernet port. Plug the other end
into your network.
Figure 2-5. Connecting to the Network
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 12
Confirm that the SIP Paging Server is Up and Running
2.3.8 Confirm that the SIP Paging Server is Up and Running
The LEDs on the front of the SIP Paging Server verify the unit’s operations.
Figure 2-6. Paging Server LEDs
Link
(GREEN/AMBER LED)
Activity
(GREEN LED)
Status
(GREEN/BLUE LED)
Paging
(GREEN LED)
2.3.8.1 Confirm Power on, Network Connectivity, and Connection Speed
When you plug in the Ethernet cable or power supply:
•
The GREEN/BLUE Status LED and the GREEN Paging LED both blink at a rate of 10 times
per second during the initial network setup.
•
The round, GREEN/BLUE Status LED on the front of the SIP Paging Server comes on
indicating that the power is on. Once the device has been initialized, this LED blinks at one
second intervals.
•
The square, GREEN/AMBER Link LED above the Ethernet port indicates that the network
connection has been established. The Link LED changes color to confirm the auto-negotiated
connection speed:
•
•
The Link LED is GREEN at 10 Mbps.
•
The Link LED is AMBER at 100 Mbps.
The GREEN Paging LED comes on after the device is booted and initialized. This LED blinks
when a page is in progress. You can disable Beep on Initialization on the Device page.
2.3.8.2 Verify Network Activity
The square, GREEN Activity LED blinks when there is network traffic.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 13
Announcing the IP Address
2.3.9 Announcing the IP Address
To announce the IP address for the SIP Paging Server, briefly press and then quickly release the
RTFM switch. See Figure 2-7.
Figure 2-7. RTFM Switch
RTFM Switch
2.3.10 Restore the Factory Default Settings
The SIP Paging Server is delivered with factory set default values for the parameters in Table 2-2. In
addition, the settings for various UI web pages (such as the Device Page, SIP Page, etc.) are
delivered with the factory default settings and can be restored to these default settings when you use
the RTFM switch. However, uploaded audio files are not restored to the factory default settings when
you use the RTFM switch.
Use the RTFM switch (see Figure 2-7) on the back of the unit to restore these parameters to the
factory default settings.
Note
When you perform this procedure, the factory default settings are restored. The default
parameters for access are shown in Table 2-2.
Table 2-2. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
DHCP
IP
Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
a
255.0.0.0
Subnet Mask
a
10.0.0.1
Default Gateway
a. Default if there is not a DHCP server present.
To restore these parameters to the factory default settings:
1. Press and hold the RTFM switch until the status and paging lights come on.
2. Continue to press the RTFM switch until after you see the indicator lights go off and you hear the
“restoring defaults” announcement.
3. Release the RTFM switch.
4. The SIP Paging Server settings are restored to the factory defaults.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 14
Gather the Required Configuration Information
2.4 Configuring the SIP Paging Server
Use this section to configure the VoIP paging server.
2.4.1 Gather the Required Configuration Information
Have the following information available before you configure the SIP Paging Server.
2.4.1.1 Static or DHCP Addressing?
Know whether your system uses static or dynamic (DHCP) IP addressing. If it uses static
addressing, you also need to know the values to assign to the following SIP Paging Server
parameters:
•
IP Address
•
Subnet Mask
•
Default Gateway
2.4.1.2 Username and Password for Configuration GUI
Determine the Username and Password that will replace the defaults after you initially log in to the
configuration GUI.
•
The Username is case-sensitive, and must be from four to 25 alphanumeric characters long.
•
The Password is case-sensitive, and must be from four to 20 alphanumeric characters long.
2.4.1.3 SIP Settings
To configure the SIP parameters, determine whether you want to register with the server. If you do,
determine the number of minutes the registration lease remains valid, and whether you want to
automatically unregister when you reboot. To configure the SIP parameters, you also need to
determine the values for these parameters:
•
SIP Server IP Address
•
Remote and Local SIP Port Numbers
•
SIP User ID, and Authenticate ID and Password for this User ID
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 15
SIP Paging Server Web Page Navigation
2.4.2 SIP Paging Server Web Page Navigation
Table 2-3 shows the navigation buttons that you will see on every SIP Paging Server web page.
Table 2-3. Web Page Navigation
Web Page Item
Description
Link to the Home page.
Link to the Device page.
Link to the Network page.
Link to go to the SIP page.
Link to the PGROUPS page.
Link to the Schedules page.
Link to the Fault page.
Link to the Audiofiles page.
Link to the Events page.
Link to the Autoprovisioning page.
Link to the Firmware page.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 16
Using the Toggle Help Button
2.4.3 Using the Toggle Help Button
The Toggle Help button allows you to see a short description of some of the settings on the
webpage. To use the Toggle Help button, do the following:
1. Click on the Toggle Help button that is on the UI webpage. See Figure 2-8 and Figure 2-9.
Figure 2-8. Toggle/Help Button
2. You will see a question mark ( ) appear next to each web page item that has been provided
with a short description by the Help feature. See Figure 2-9.
Figure 2-9. Toggle Help Button and Question Marks
Question mark 
appears next to the
web page items
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 17
Using the Toggle Help Button
3. Move the mouse pointer to hover over the question mark (
page item will appear. See Figure 2-10.
), and a short description of the web
Figure 2-10. Short Description Provided by the Help Feature
Question mark
CyberData Corporation
931073J
A short description of the 
web page item will appear
Operations Guide
Setting Up the SIP Paging Server 18
Log in to the Configuration GUI
2.4.4 Log in to the Configuration GUI
1. Open your browser to the SIP Paging Server IP address.
Note
If the network does not have access to a DHCP server, the device will default to an IP
address of 10.10.10.10.
Note
Make sure that the PC is on the same IP network as the SIP Paging Server.
Note
You may also download CyberData’s VoIP Discovery Utility program which allows you to
easily find and configure the default web address of the CyberData VoIP products. 

CyberData’s VoIP Discovery Utility program is available at the Downloads tab on the
following webpage:
https://www.cyberdata.net/products/011146
The unit ships in DHCP mode. To get to the Home page, use the discovery utility to scan for
the device on the network and open your browser from there.
Note
To work with the SIP Paging Server configuration after the initial configuration, log in using
the IP address you assign to the device. Section 2.4.6, "Configure the Network Parameters"
provides instructions for entering the IP address.
2. When prompted, use the following default Username and Password to open the configuration
Home page:
Username: admin
Password: admin
Change the
To change the default Web access Username and Password:
Default Username
1. Enter the new Username from four to 25 alphanumeric characters in the Change Username
and Password
field. The Username is case-sensitive.
2. Enter the new Password from four to 20 alphanumeric characters in the Change Password
field. The Password is case-sensitive.
3. Enter the new password again in the Re-enter New Password field.
Click Save Settings.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 19
Log in to the Configuration GUI
Figure 2-11. Home Page
146100001
v12.1.0
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 20
Log in to the Configuration GUI
4. On the Home Page, review the setup details and navigation buttons described in Table 2-4
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-4. Home Page Overview
Web Page Item
Description
Admin Settings
Username
The username to access the web interface. Enter up to 25 characters.
Password
The password to access the web interface. Enter up to 25 characters.
Confirm Password
Confirm the web interface password.
Current Status
Serial Number
Shows the device serial number.
Mac Address
Shows the device Mac address.
Firmware Version
Shows the current firmware version.
IP Addressing
Shows the current IP addressing setting (DHCP or static).
IP Address
Shows the current IP address.
Subnet Mask
Shows the current subnet mask address.
Default Gateway
Shows the current default gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
SIP Mode
Shows the current status of the SIP mode.
Event Reporting
Shows the current status of the Event Reporting mode.
Nightringer
Shows the current status of the Nightringer mode.
Primary SIP Server
Shows the current status of the Primary SIP Server.
Backup Server 1
Shows the current status of Backup Server 1.
Backup Server 2
Shows the current status of Backup Server 2.
Nightringer Server
Shows the current status of Nightringer Server.
Import Settings
Use this button to select a configuration file to import.
After selecting a configuration file, click Import to import the
configuration from the selected file. Then, click Save and Reboot to
store changes.
Export Settings
Click Export to export the current configuration to a file.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 21
Log in to the Configuration GUI
Table 2-4. Home Page Overview (continued)
Web Page Item
Description
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you will
see a question mark ( ) appear next to some of the web page items.
Move the mouse pointer to hover over a question mark to see a short
description of a specific web page item.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
At this point you can:
•
Review the SIP Paging Server’s Current Settings. Use the RTFM switch to restore the factory
default settings. See Section 2.3.10, "Restore the Factory Default Settings".
•
Configure the device parameters. Click on the Device button and see Section 2.4.5, "Configure
the Device Parameters" for instructions.
•
Configure the network parameters. Click on the Network button and see Section 2.4.6,
"Configure the Network Parameters" for instructions.
•
Configure the SIP parameters. Click on the SIP button and see Section 2.4.7, "Configure the
SIP Parameters" for instructions.
•
Configure the PGROUPS parameters. Click on the PGROUPS button and see Section 2.4.8,
"Configure the Paging Groups (PGROUPS) Parameters" for instructions.
•
Configure the fault detection parameters. Click on the Fault button and see Section 2.4.11,
"Configure the Fault Detection Parameters" for instructions.
•
Configure the audio parameters. Click on the Audiofiles button and see Section 2.4.12,
"Configure the Audio Parameters" for instructions.
•
Configure the event parameters. Click on the Events button and see Section 2.4.13, "Configure
the Event Parameters" for instructions.
•
Configure the autoprovisioning parameters. Click on the Autoprov button and see Section
2.4.14, "Configure the Autoprovisioning Parameters" for instructions.
Note
CyberData Corporation
Click on the Firmware button any time you need to upload new versions of the firmware.
See Section 2.5, "Upgrading the Firmware" for instructions.
931073J
Operations Guide
Setting Up the SIP Paging Server 22
Configure the Device Parameters
2.4.5 Configure the Device Parameters
Miscellaneous device settings such as the page prompt and analog options are configured on this
page. In addition, you may also enable Polycom Paging to page Polycom IP phones using their
proprietary Polycom Paging protocol.
1. Click on the Device button to open the Device page. See Figure 2-12.
Figure 2-12. Device Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 23
Configure the Device Parameters
2. On the Device page, you may enter values for the parameters indicated in Table 2-5.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-5. Device Configuration Parameters
Web Page Item
Description
Line-in Settings
Enable Line-in to Line-out Loopback
Line-in audio will play back out the device's audio output
ports. This is the lowest priority audio and will be
preempted by any other audio stream.
Enable Line-in to Multicast
Line-in audio will be sent to the specified multicast
address and port. Playback priority is determined by
receiver(s)
Cannot be combined with Play Line-in Audio via
Multicast (Fault Detection)
Multicast Address
Address line-in audio will be sent to.
Multicast Port
Port line-in audio will be sent to (1-65535).
Detect Line-in Silence
If silence is detected on line-input, the multicast stream
will be stopped to reduce network traffic.
Relay Settings
Activate Relay on Local Audio
The relay will be activated (closed) when the device is
playing audio. Use this to activate an external amplifier
when the device is playing audio.
Clock Settings
Set Time with NTP Server on boot
When selected, the time is set with an external NTP
server when the device restarts.
NTP Server
Use this field to set the address (in IPv4 dotted decimal
notation or as a canonical name) for the NTP Server. This
field can accept canonical names of up to 64 characters in
length.
Posix Timezone String
See Section 2.4.5.2, "Time Zone Strings" for information
about how to use the Posix Timezone String to specify
time zone and daylight savings time where applicable.
Enter up to 63 characters.
Periodically sync time with server
When selected, the time is periodically updated with the
NTP server at the configured interval below.
Time update period (in hours)
The time interval after which the device will contact the
NTP server to update the time. Enter up to 4 digits.
Current Time
Allows you to input the current time. (6 character limit)
Misc Settings
Device Name
Type the device name. Enter up to 25 characters.
Bypass DTMF
Bypassing DTMF will result in all calls being relayed to
PGROUP 0 Any security code entered for PGROUP 0 will
be ignored if DTMF is bypassed
DTMF Duration
The duration, in milliseconds, of DTMF tones played out of
the device's analog audio ports (0-65535).
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 24
Configure the Device Parameters
Table 2-5. Device Configuration Parameters (continued)
Web Page Item
Description
Beep on Init
Device will play the user defined “pagetone” audio file
when it boots.
Beep on Page
Device will play the user defined “pagetone” audio file
before playing a SIP page.
Enable Polycom Paging on Multicast
Enabling Polycom Paging will result in a standard RTP
multicast being sent to the specified address and port and
a Polycom Group Paging multicast being sent to the
specified address and port+1.
Polycom Transmit Channel
Destination channel for Polycom Group Paging multicast.
Disable HTTPS (NOT recommended)
Disables the encrypted connection to the webpage. We do
not recommend disabling HTTPS for security reasons.
Click on the Test Audio button to do an audio test. When
the Test Audio button is pressed, you will hear a voice
message for testing the device audio quality and volume.
This button will cause the device to send a 5 second
ULAW multicast stream to 234.2.1.200:2200.
Click on the Test Relay button to do a relay test.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description
of some of the web page items. First click on the Toggle
Help button, and you will see a question mark ( ) appear
next to some of the web page items. Move the mouse
pointer to hover over a question mark to see a short
description of a specific web page item.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.4.5.1 Polycom Paging
The Polycom Paging feature is supported on Polycom IP phones using UC Software 4.0.0 and
higher. The Polycom paging feature operates in two modes: Push-to-Talk (PTT) and Group Paging
Only Group Paging mode pages are supported by the Paging Server.
Polycom phones use the same multicast IP address and port number for both PTT and Group
Paging multicasts. Make sure to note the Polycom multicast IP address and port number before
configuring the CyberData V3 Paging Server. Polycom phones use a default multicast IP address of
224.0.1.116 and odd-numbered port 5001.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 25
Configure the Device Parameters
While the same multicast IP address and port number is used for all Polycom pages in both modes,
Polycom uses numbered "groups" or "channels" to differentiate between each paging group. Each
"group" or "channel" is numbered 1 through 25.
The Paging Server can transmit to Group Paging groups 1 through 25 only for one-way audio pages.
The transmit channel is configurable. The Polycom phones must subscribe to this channel in order to
receive one-way audio pages from the Paging Server.
When configuring Polycom phones for their Group Paging feature, be sure the following settings are
configured:
•
Payload Size = 20 ms (milliseconds)
•
Codec = G.711Mu
The Polycom Group Paging multicast transmitted by the Paging Server is G.711Mu encoded with a
payload size of 20 ms.
It is imperative to note the Paging Server assumes the Polycom phones will use an odd-numbered
port. Since it is not possible to configure the V3 Paging Server to transmit multicasts on oddnumbered ports (which maintains conformance with RFC 1889), it is necessary to use the next lower
even port number when specifying the Polycom multicast IP address and port number on the
PGROUPS Page. Using the Polycom default port 5001 will require you to configure the Paging
Server to transmit on the next lower even port 5000.
Thus, configuring the Paging Server for Polycom Paging is a two-step process:
1. Enable Polycom Paging on the Paging Server by checking the box to Enable Polycom Paging
on Multicast on the Device Page.
2. Specify the Polycom IP address and use the next lower even port number for the desired paging
group on the PGROUPS Page.
3. Save and reboot to store changes.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 26
Configure the Device Parameters
2.4.5.2 Time Zone Strings
The posix time zone string tells the internal date and time utilities how to handle daylight savings
time for different time zones. Table 2-6 shows some common strings.
Table 2-6. Common Time Zone Strings
Time Zone
Time Zone String
US Pacific time
PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Mountain time
MST7MDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Eastern Time
EST5EDT,M3.2.0/2:00:00,M11.1.0/2:00:00
a
Phoenix Arizona
MST7
US Central Time
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
a.Phoenix, Arizona does not use daylight savings time.
Table 2-7 shows a breakdown of the parts that constitute the following time zone string:
●
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
Table 2-7. Time Zone String Parts
Time Zone String
Part
Meaning
CST6CDT
The time zone offset from GMT and three character identifiers for the time zone.
CST
Central Standard Time
6
The (hour) offset from GMT/UTC
CDT
Central Daylight Time
M3.2.0/2:00:00
The date and time when daylight savings begins.
M3
The third month (March)
.2
The 2nd occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
M11.1.0/2:00:00
The date and time when daylight savings ends.
M11
The eleventh month (November)
.1
The 1st occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 27
Configure the Device Parameters
Time Zone String
Examples
Table 2-8 has some more examples of time zone strings.
Table 2-8. Time Zone String Examples
Time Zone
Time Zone String
a
Tokyo
IST-9
Berlinb
CET-1MET,M3.5.0/1:00,M10.5.0/1:00
a.Tokyo does not use daylight savings time.
b.For Berlin, daylight savings time starts on the last Sunday in March at
01:00 UTC, and ends on the last Sunday in October at 01:00 UTC, and is one
hour ahead of UTC.
Time Zone Identifier A user-definable three or four character time zone identifier (such as PST, EDT, IST, MUT, etc) is
needed at the beginning of the posix time zone string to properly set the time. However, the specific
letters or numbers used for the time zone identifier are not important and can be any three or four
letter or number combination that is chosen by the user. However, the time zone identifier cannot be
blank.
Figure 2-13. Three or Four Character Time Zone Identifier
PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00
Three or four character time zone identifier at the beginning of the time zone string.
The identifier can be any three or four letter or number combination chosen by the user.
You can also use the following URL when a certain time zone applies daylight savings time:
http://www.timeanddate.com/time/dst/2011.html
World GMT Table
Table 2-9 has information about the GMT time in various time zones.
Table 2-9. World GMT Table
Time Zone
City or Area Zone Crosses
GMT-12
Eniwetok
GMT-11
Samoa
GMT-10
Hawaii
GMT-9
Alaska
GMT-8
PST, Pacific US
GMT-7
MST, Mountain US
GMT-6
CST, Central US
GMT-5
EST, Eastern US
GMT-4
Atlantic, Canada
GMT-3
Brazilia, Buenos Aries
GMT-2
Mid-Atlantic
GMT-1
Cape Verdes
GMT
Greenwich Mean Time, Dublin
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 28
Configure the Device Parameters
Table 2-9. World GMT Table (continued)
Time Zone
City or Area Zone Crosses
GMT+1
Berlin, Rome
GMT+2
Israel, Cairo
GMT+3
Moscow, Kuwait
GMT+4
Abu Dhabi, Muscat
GMT+5
Islamabad, Karachi
GMT+6
Almaty, Dhaka
GMT+7
Bangkok, Jakarta
GMT+8
Hong Kong, Beijing
GMT+9
Tokyo, Osaka
GMT+10
Sydney, Melbourne, Guam
GMT+11
Magadan, Soloman Is.
GMT+12
Fiji, Wellington, Auckland
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 29
Configure the Network Parameters
2.4.6 Configure the Network Parameters
Configuring the network parameters enables your network to recognize the SIP Paging Server and
communicate with it. Click the Network button on the Home page to open the Network page.
Figure 2-14. Network Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 30
Configure the Network Parameters
On the Network page, enter values for the parameters indicated in Table 2-10.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-10. Network Configuration Parameters
Web Page Item
Description
Stored Network Settings
Addressing Mode
Select either DHCP IP Addressing or Static Addressing by marking
the appropriate radio button. DHCP Addressing mode is enabled on
default and the device will attempt to resolve network addressing with
the local DHCP server upon boot. If DHCP Addressing fails, the
device will revert to the last known IP address or the factory default
address if no prior DHCP lease was established. See Section 2.3.10,
"Restore the Factory Default Settings" for factory default settings. Be
sure to click Save and Reboot to store changes when configuring a
Static address.
Hostname
This is the hostname provided by the DHCP server. See the
DHCP/DNS server documentation for more information. Enter up to
64 characters.
IP Address
Enter the Static IPv4 network address in dotted decimal notation.
Subnet Mask
Enter the Subnet Mask in dotted decimal notation.
Default Gateway
Enter the Default Gateway IPv4 address in dotted decimal notation.
DNS Server 1
Enter the primary DNS Server IPv4 address in dotted decimal
notation.
DNS Server 2
Enter the secondary DNS Server IPv4 address in dotted decimal
notation.
DHCP Timeout in seconds
Specify the desired time-out duration (in seconds) that the device will
wait for a response from the DHCP server before reverting back to
the stored static IP address. The stored static IP address may be the
last known IP address or the factory default address if no prior DHCP
lease was established. Enter up to 8 characters. A value of -1 will
retry forever.
VLAN Settings
VLAN ID (0-4095)
Specify the IEEE 802.1Q VLAN ID number. Enter up to 4 digits.
Note: The device supports 802.1Q VLAN tagging support. The
switch port connected to the device will need to be in “trunking mode”
for the VLAN tags to propagate.
VLAN Priority (0-7)
Specify the IEEE 802.1p VLAN priority level. Enter 1 digit. A value of
0 may cause the VLAN ID tag to be ignored.
Current Network Settings
Shows the current network settings.
IP Address
Shows the current Static IP address.
Subnet Mask
Shows the current Subnet Mask address.
Default Gateway
Shows the current Default Gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 31
Configure the Network Parameters
Table 2-10. Network Configuration Parameters (continued)
Web Page Item
Description
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you
will see a question mark ( ) appear next to some of the web page
items. Move the mouse pointer to hover over a question mark to see
a short description of a specific web page item.
On this page:
1. Specify whether you use Static or DHCP IP Addressing by marking the appropriate radio
button. If you select Static IP Addressing, go to Step 2.
2. For Static IP Addressing, also enter values for the following parameters:
•
The SIP Paging Server’s IP Address: The SIP Paging Server is delivered with a factory
default IP address. Change the default address to the correct IP address for your system.
•
The Subnet Mask.
•
The Default Gateway.
Note
CyberData Corporation
You must click on the Save button and then the Reboot button for the changes to take
effect.
931073J
Operations Guide
Setting Up the SIP Paging Server 32
Configure the SIP Parameters
2.4.7 Configure the SIP Parameters
The SIP parameters enable the device to contact and register with the SIP server. On the Home
page, click SIP Config to open the SIP page.
Figure 2-15. SIP Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 33
Configure the SIP Parameters
On the SIP page, enter values for the parameters indicated in Table 2-11.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-11. SIP Configuration Parameters
Web Page Item
Description
SIP Settings
Enable SIP Operation
When enabled, the device will transmit, receive, and process SIP messages
according to the configured SIP settings below.
Register with a SIP Server
When enabled, the device will attempt to register to the configured SIP
Server(s) on this page. To configure the device to send and receive point-topoint SIP calls, enable SIP Operation and disable Register with a SIP Server
(see Section 2.4.7.1, "Point-to-Point Configuration").
Use Cisco SRST
When enabled, the backup servers are handled according to Cisco SRST
(Survivable Remote Site Telephony). It is required for use in clustered Cisco
Unified Communications Manager topologies.
Primary SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal notation or a
fully qualified domain name. This parameter also becomes the host portion of
the SIP-URI for the device's extension on the primary SIP server. This field can
accept entries of up to 255 characters in length.
Primary SIP User ID
Specify the SIP User ID for the Primary SIP Server. This parameter becomes
the user portion of the SIP-URI for the device's extension on the primary SIP
server. Enter up to 64 alphanumeric characters.
Primary SIP Auth ID
Specify the Authenticate ID for the Primary SIP Server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Primary SIP Auth Password
Specify the Authenticate Password for the Primary SIP Server. This parameter
is required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Backup SIP Server 1
Enter the backup SIP server address as an IPv4 address in dotted decimal
notation or a fully qualified domain name. This parameter also becomes the
host portion of the SIP-URI for the device's extension on the backup SIP server.
This field can accept entries of up to 255 characters in length.
Backup SIP User ID 1
Specify the SIP User ID for the first backup SIP Server. This parameter
becomes the user portion of the SIP-URI for the device's extension on the first
backup SIP server. Enter up to 64 alphanumeric characters.
Backup SIP Auth ID 1
Specify the Authenticate ID for the first backup SIP server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Backup SIP Auth Password 1
Specify the Authenticate Password for the first backup SIP server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Backup SIP Server 2
Enter a second backup SIP server address as an IPv4 address in dotted
decimal notation or a fully qualified domain name. This parameter also becomes
the host portion of the SIP-URI for the device's extension on the second backup
SIP server. This field can accept entries of up to 255 characters in length.
Backup SIP User ID 2
Specify the SIP User ID for the second backup SIP Server. This parameter
becomes the user portion of the SIP-URI for the device's extension on the
second backup SIP server. Enter up to 64 alphanumeric characters.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 34
Configure the SIP Parameters
Table 2-11. SIP Configuration Parameters (continued)
Web Page Item
Description
Backup SIP Auth ID 2
Specify the Authenticate ID for the second backup SIP server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Backup SIP Auth Password 2
Specify the Authenticate Password for the second backup SIP server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Remote SIP Port
The Remote SIP Port is the port number the device will use as the destination
port when sending SIP messages. The default Remote SIP Port is 5060. The
supported range is 0-65536. Enter up to 5 digits.
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP
messages. The default Local SIP Port is 5060. The supported range is 0-65536.
Enter up to 5 digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal
notation or a fully qualified domain name (FQDN). When an IP address is
configured, the device will send all SIP messages to this IP address. When an
FQDN is configured, the device will run DNS NAPTR, SRV, and A queries on
the FQDN to resolve an IP address to which it will send all SIP messages. This
field can accept entries of up to 255 characters in length.
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port when
sending SIP messages to the outbound proxy. A value of 0 will default to 5060.
The supported range is 0-65536. Enter up to 5 digits.
Disable rport Discovery
Disabling rport Discovery will prevent the device from including the public WAN
IP address and port number in the contact information that is sent to the remote
SIP servers. This will generally only need to be enabled when using an SBC or
SIP ALG in conjunction with a remote SIP server.
Buffer SIP Calls
Also referred to as "delayed paging." Device will buffer up to four minutes of
audio then play back the recording after hang up or after the buffer is full.
Re-registration Interval (in seconds)
The SIP Re-registration interval (in seconds) is the SIP Registration lease time,
also known as the expiry. The supported range is 30-3600 seconds. Enter up to
4 digits.
Unregister on Boot
When enabled, the device will send one registration with an expiry of 0 on boot.
Keep Alive Period
The minimum time in milliseconds between keep-alive packets sent for nat
traversal. A value of 0 will disable keep alive packets.
RTP Settings
RTP Port (even)
Specify the port number used for the RTP stream after establishing a SIP call.
This port number must be an even number and defaults to 10500. The
supported range is 0-65536. Enter up to 5 digits.
Jitter Buffer
Specify the size of the jitter buffer (in milliseconds) used for SIP calls. Valid
values are 50-1000.
Nightringer Settings
Enable Nightringer
CyberData Corporation
When Nightringer is enabled, the device will attempt to register a second
extension with the SIP server. Any calls made to this extension will play a
ringtone (corresponds to Night Ring on the Audiofiles page). By design, it is
not possible to answer a call to the Nightringer extension.
931073J
Operations Guide
Setting Up the SIP Paging Server 35
Configure the SIP Parameters
Table 2-11. SIP Configuration Parameters (continued)
Web Page Item
Description
SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal notation or a
fully qualified domain name. This parameter also becomes the host portion of
the SIP-URI for the device's Nightringer extension on the SIP server. This field
can accept entries of up to 255 characters in length.
Remote SIP Port
The Remote SIP Port is the port number the device will use as the destination
port when sending SIP messages for the Nightringer extension. The default
Remote SIP Port is 5060. The supported range is 0-65536. Enter up to 5 digits.
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP
messages for the Nightringer extension. This value cannot be the same as the
Local SIP Port for the primary extension. The default Local SIP Port is 5061.
The supported range is 0-65536. Enter up to 5 digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal
notation or a fully qualified domain name (FQDN). When an IP address is
configured, the device will send all SIP messages to this IP address for the
Nightringer extension. When an FQDN is configured, the device will run DNS
NAPTR, SRV, and A queries on the FQDN to resolve an IP address to which it
will send all SIP messages for the Nightringer extension. This field can accept
entries of up to 255 characters in length.
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port when
sending SIP messages to the outbound proxy for the Nightringer extension. A
value of 0 will default to 5060. The supported range is 0-65536. Enter up to 5
digits.
User ID
Specify the SIP User ID for the SIP server. This parameter becomes the user
portion of the SIP-URI for the device's Nightringer extension. Enter up to 64
alphanumeric characters.
Authenticate ID
Specify the Authenticate ID for the SIP Server. This parameter is required for
SIP registration authentication. Enter up to 64 alphanumeric characters.
Authenticate Password
Specify the Authenticate Password for the SIP Server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Re-registration Interval (in seconds)
The SIP Re-registration Interval (in seconds) is the SIP Registration lease time,
also known as the expiry. The supported range is 30-3600 seconds. Enter up to
4 digits.
Relay rings to multicast
When selected, the device will play ring tones to the specified multicast address
and port.
Multicast Address
The multicast address used for nightring audio.
Multicast Port
The multicast port used for nightring audio.
Call Disconnection
Terminate Call After Delay
Automatically terminate an active call after a given delay in seconds. A value of
0 will disable this function. Enter up to 8 digits.
Codec Selection
Force Selected Codec
When configured, this option will allow you to force the device to negotiate for
the selected codec [PCMU(G.711, u-law), PCMA(G.711, a-law), or G.722].
Otherwise, the device will perform codec negotiation using the default list of
supported codecs.
Codec
Select desired codec (only one may be chosen).
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 36
Configure the SIP Parameters
Table 2-11. SIP Configuration Parameters (continued)
Web Page Item
Description
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web
page items. First click on the Toggle Help button, and you will see a question
mark ( ) appear next to some of the web page items. Move the mouse pointer
to hover over a question mark to see a short description of a specific web page
item.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
Note
For specific server configurations, go to the following website address:
https://www.cyberdata.net/pages/connecting-to-ip-pbx-servers
1. Enter the IP address of the SIP Server.
2. Enter the port numbers used for SIP signaling:
a. Remote SIP Port
b. Local SIP Port
3. Enter the SIP registration parameters:
a. SIP User ID
b. Authenticate ID
c. Authenticate Password
4. For SIP Registration, designate whether you want the VoIP Paging Server to register with your
SIP server.
5. At Unregister on Reboot:
a. Select Yes to automatically unregister the SIP Paging Server when you reboot it.
b. Select No to keep the SIP Paging Server registered when you reboot it.
6. In the Register Expiration field, enter the number of seconds the SIP Paging Server
registration lease remains valid with the SIP Server. The SIP Paging Server automatically reregisters with the SIP server before the lease expiration timeout.
Note
CyberData Corporation
You must click on the Save button and then the Reboot button for the changes to take
effect.
931073J
Operations Guide
Setting Up the SIP Paging Server 37
Configure the SIP Parameters
2.4.7.1 Point-to-Point Configuration
When the board is set to not register with a SIP server, it's possible to set the device to dial out to a
single endpoint. To do this, do the following:
1. On the SIP page (Figure 2-16), make sure that the Register with a SIP Server parameter is not
selected.
2. Type the IP address of the remote device that you want to contact into the Dial out Extension
field
Note
Establishing point-to-point SIP calls may not work with all phones.
Figure 2-16. SIP Page Set to Point-to-Point Mode
Device is set to NOT register with a SIP server
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 38
Configure the Paging Groups (PGROUPS) Parameters
2.4.8 Configure the Paging Groups (PGROUPS) Parameters
Note
A PGROUP is a way of assigning multicast addresses and port numbers when configuring
multicast paging speakers.
To assign a multicast address, you must first configure the speakers that you want to put into
a paging zone by entering a particular multicast address and port number combination in the
web configuration for these speakers.
1. Click on the PGROUPS button to open the PGROUPS page. See Figure 2-17.
Figure 2-17. PGROUPS Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 39
Configure the Paging Groups (PGROUPS) Parameters
Figure 2-18. PGROUPS Page (continued)
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 40
Configure the Paging Groups (PGROUPS) Parameters
Figure 2-19. PGROUPS Page (continued)
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 41
Configure the Paging Groups (PGROUPS) Parameters
2. On the PGROUPS page, enter values for the parameters indicated in Table 2-12.
Table 2-12. PGROUPS Parameters
Web Page Item
Description
#
Shows the paging group number.
Address
Shows the IP address of the PGROUP.
Port
Shows the port number of the PGROUP.
Name
Shows the name of the PGROUP.
Code
Shows the security code of the PGROUP.
TTL
Shows the "time to live" of the PGROUP.
Lineout
Shows the Lineout setting of the PGROUP.
Click on the Reboot button to reboot the system.
To make changes to the paging groups, complete the following steps:
1. Click on the Edit button to open the Configure PGROUP window (Figure 2-20).
2. In the Configure PGROUP window (Figure 2-20), edit the PGROUP (see Table 2-13, "Configure
PGROUP Window") and click on the Save Changes button.
3. On the PGROUPS page (Figure 2-19), click on the Reboot button.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 42
Configure the Paging Groups (PGROUPS) Parameters
Figure 2-20. Configure PGROUP Window
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 43
Configure the Paging Groups (PGROUPS) Parameters
The parameters for the Configure PGROUP window are shown in Table 2-13.
Table 2-13. Configure PGROUP Window
Web Page Item
Description
PGROUP
Shows the paging group number.
Address
Enter the IP address of the PGROUP.
Note: To disable a relay on a group, use an IP address of 0.0.0.0.
Port
Enter the port number of the PGROUP.
Note: The port range can be from 2000 to 65534 and must be even. When configuring a Paging
Group for Polycom Group Paging using an odd-numbered port, configure the next lower even port
number. For example, when using the default Polycom paging port 5001 on Polycom phones,
configure the next lower even port 5000 for the desired V3 Paging Server's Paging Group port.
Name
Enter a name for the PGROUP.
Security Code
This field allows the user to add a security code to prevent unauthorized paging to the PGROUP.
Code must be between two to five numeric digits (0 through 9). Leave the field empty for no security
code. Any security code entered for PGROUP 0 will be ignored if DTMF is bypassed.
TTL
The TTL field allows you to adjust the TTL. TTL is "time to live" and it describes how many networks
(routers) a packet will go through before it is discarded.
Lineout
The Lineout field determines whether or not the device will play audio out of the RCA output port and
the 600 Ohm output port in addition to forwarding it to the PGROUP.
Play Stored Message
When selected, entering this paging group will play the stored message selected in Audio File.
Audio File
Select a file from the drop down list of audio files previously saved in the Stored Messages portion of
the Audiofiles Page.
Times to Play
Enter the number of times the message will play (1-65535).
Click the Save Changes button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click the Cancel button to close the Configure PGROUP window.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 44
Operating the Paging Server
2.4.9 Operating the Paging Server
Call behavior changes based on the configuration of the PGROUPs page.
2.4.9.1 DTMF Bypassed
•
When the SIP Paging Server is called, it will send the "page tone" audio message to the caller.
•
When the caller hears this message, the caller should begin speaking.
2.4.9.2 DTMF Not Bypassed
•
When the SIP Paging Server is called, it sends the "Enter PGROUP" audio message to the
caller. By default, this message is "Enter the two digit zone number."
•
When the caller hears this message, the caller should enter the two-digit code for the zone that
the caller wants to page.
•
If the zone is invalid or not configured, the SIP Paging Server sends the "Invalid PGROUP"
audio message to the caller. By default this message is "Invalid zone number. Enter the two digit
zone number." The caller should repeat the previous step.
•
If a security code is enabled on the zone, the SIP Paging Server sends the "Enter Code" audio
message to the caller. By default this message is "Enter the security code." When the caller
hears this message, the caller should enter the security code for the selected zone. If no
security code is enabled on the zone, the SIP Paging Server will send the "page tone" audio
message to the caller. The caller should begin speaking when this message is heard.
•
If the security code is invalid, the SIP Paging Server will send the "Invalid Code" audio message
to the caller. By default this message is "Invalid Security code. Enter the security code." The
caller should repeat the previous step. When a valid security code is entered, the SIP Paging
Server will send the "page tone" audio message to the caller. The caller should begin speaking
when this message is heard.
•
For page-all, you simply configure all speakers with a particular multicast address and port
number combination, which represents one of the 100 zones that the paging server will initially
support. Each speaker can still be part of 100 other paging zones in addition to the one page-all
zone.
•
The SIP Paging Server can negotiate the multicast stream via SIP regardless of the bypass
state. However, if the SIP Paging Server is not in bypass mode (or the multicast sender does not
send any DTMF), the device will not play or relay any audio because the device will be waiting at
the zone entry prompt. The DTMF from the sender would have to be sent as RFC2833 RTP
events (i.e. "out of band").
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 45
Configure the Schedules Parameters
2.4.10 Configure the Schedules Parameters
1. Click on the Schedules button to open the Schedules page. See Figure 2-21.
Figure 2-21. Schedules Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 46
Configure the Schedules Parameters
2. On the Schedules page, enter values for the parameters indicated in Table 2-16.
Table 2-14. Schedules Configuration Parameters
Web Page Item
Description
Scheduled Events
Days
Shows the days of the scheduled event.
Time
Shows the time of the scheduled event.
Audio File
Shows the audio file that is associated with the scheduled event.
Event Name
Shows the name of the scheduled event.
Opens the Configure Scheduled Event window for the
corresponding event. See Figure 2-22, "Configure Scheduled
Event Window" and Table 2-15, "Configure Scheduled Event
Window Parameters"
Removes the event from the schedule.
Opens a new Configure Scheduled Event window.
After selecting a file, imports a schedule.
Exports the current schedule.
Reboots the device, which must be rebooted for changes to the
schedule to take effect.
Note
CyberData Corporation
The schedule is not affected by restoring the factory defaults.
931073J
Operations Guide
Setting Up the SIP Paging Server 47
Configure the Schedules Parameters
Figure 2-22. Configure Scheduled Event Window
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 48
Configure the Schedules Parameters
The parameters for the Configure Scheduled Event window are shown in Table 2-15.
Table 2-15. Configure Scheduled Event Window Parameters
Web Page Item
Description
Days
Use the box beneath the day to select. Multiple days may be selected.
Time
Enter time of the event, in the form HH:MM, using the 24 hour clock.
Audio
Choose the audio file to be played from the drop down list, which displays files previously uploaded in
the Bells section of the Audio Files web page.
PGroup
Select the paging group from the drop down menu.
Name
Enter the name of the event, using a maximum of 16 characters.
Relay
A relay can be activated or deactivated at the time of a scheduled bell.
The relay options are :
Activate during bell — The relay will be active while the bell is playing
Activate indefinitely — The relay will be activated indefinitely.
Deactivate indefinitely — The relay will be deactivated indefinitely.
Click the Save Changes button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click the Cancel button to close the Configure Scheduled Event window.
•
In addition to the bells, the user can have 25 stored messages that are utilized through paging
groups.
•
www.cyberdata.net/bell-download/ has a set of sounds that can be downloaded.
•
The user can upload 25 unique bell files that can be used in up to 250 scheduled events.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 49
Configure the Fault Detection Parameters
2.4.11 Configure the Fault Detection Parameters
1. Click on the Fault button to open the Fault page. See Figure 2-23.
Figure 2-23. Fault Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 50
Configure the Fault Detection Parameters
2. On the Fault Detection page, enter values for the parameters indicated
in Table 2-16.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-16. Fault Detection Configuration Parameters
Web Page Item
Description
Triggered Settings
Play Stored Audio Locally
When selected, the device will play the user defined “sensor
triggered” audio file when the fault detection is triggered.
Make Call to Extension
When selected, the device will call an extension when fault
detection is triggered. Use the Dial Out Extension field to specify
the extension the device will call.
Dial Out Extension
Specify the extension the device will call when fault detection is
triggered. Enter up to 64 alphanumeric characters.
Dial Out ID
An additional Caller identification string added to outbound calls.
Enter up to 64 alphanumeric characters.
Repeat Message
The number of times to repeat the audio message through the
local speaker or to the remote endpoint. A value of 0 will repeat
forever. Enter a value from 0-65536.
Play Stored Audio via Multicast
When selected, the device will send the user-defined “sensor
triggered” audio file to the specified multicast address and port.
Cannot be combined with Play Line-in Audio via Multicast.
Play Line-in Audio via Multicast
When selected, the device will send line-in audio to the specified
multicast address and port. Cannot be combined with Play Stored
Audio via Multicast or Enable Line-in to Line-out Loopback.
Multicast Address
The multicast address used for fault detection audio.
Multicast Port
The multicast port used for fault detection audio.
Click on the Test Fault Detection button to test the fault detection
feature.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some
of the web page items. First click on the Toggle Help button, and
you will see a question mark ( ) appear next to some of the web
page items. Move the mouse pointer to hover over a question
mark to see a short description of a specific web page item.
Note
CyberData Corporation
You must click on the Save button and then the Reboot button for the changes to take
effect.
931073J
Operations Guide
Setting Up the SIP Paging Server 51
Configure the Audio Parameters
2.4.12 Configure the Audio Parameters
Click on the Audiofiles button to open the Audiofiles page. See Figure 2-24. The Audiofiles page
is used to add custom audio to the board. User uploaded audio will take precedence over the audio
files shipped with the device.
Figure 2-24. Audiofiles Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 52
Configure the Audio Parameters
Figure 2-25. Audiofiles Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 53
Configure the Audio Parameters
On the Audiofiles page, enter values for the parameters indicated in Table 2-17.
Note
Each entry on the Audiofiles page replaces one of the stock audio files on the board. When
the input box displays the word default, the SIP Paging Server is using the stock audio file.
If that file is replaced with a user file, it will display the uploaded filename.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-17. Audiofiles Configuration Parameters
Web Page Item
Description
Audio Files
0-9
The name of the audio configuration option is the same as the spoken audio that plays on the board (24
character limit).
'0' corresponds to the spoken word “zero.”
'1' corresponds to the spoken word “one.”
'2' corresponds to the spoken word “two.”
'3' corresponds to the spoken word “three.”
'4' corresponds to the spoken word “four.”
'5' corresponds to the spoken word “five.”
'6' corresponds to the spoken word “six.”
'7' corresponds to the spoken word “seven.”
'8' corresponds to the spoken word “eight.”
'9' corresponds to the spoken word “nine.”
Dot
Corresponds to the spoken word “dot.” (24 character limit).
Audio Test
Corresponds to the message “This is the CyberData IP speaker test message...” (24 character limit).
Enter PGROUP
Corresponds to the message “Enter PGROUP” (24 character limit).
Invalid PGROUP
Corresponds to the message “Invalid PGROUP” (24 character limit).
Enter Code
Corresponds to the message “Enter Code” (24 character limit).
Invalid Code
Corresponds to the message “Invalid Code” (24 character limit).
Page Tone
Corresponds to a simple tone that is unused by default (24 character limit).
Your IP Address is
Corresponds to the message “Your IP address is...” (24 character limit).
Rebooting
Corresponds to the spoken word “Rebooting” (24 character limit).
Restoring Default
Corresponds to the message “Restoring default” (24 character limit).
Sensor Triggered
Corresponds to the message “Sensor Triggered” (24 character limit).
Night Ring
Specifies the ringtone for nightring. By default this parameter uses the same audio file that is selected for
the Ring Tone parameter.
Bells
Upload files here to be used in scheduled events.
Note: The user may upload a maximum of 25 files.
Stored Messages
Upload files here to be used as stored messages.
Note: The user may upload a maximum of 25 files.
The Browse button will allow you to navigate to and select an audio file.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 54
Configure the Audio Parameters
Table 2-17. Audiofiles Configuration Parameters (continued)
Web Page Item
Description
The Play button will play that audio file.
The Delete button will delete any user uploaded audio and restore the stock audio file.
The Save button will download a new user audio file to the board once you've selected the file by using
the Browse button. The Save button will delete any pre-existing user-uploaded audio files.
2.4.12.1 User-created Audio Files
User-created audio files must be saved in one of the following formats:
•
RIFF (little-endian) data,
•
WAVE audio, Microsoft PCM
•
16 bit, mono 8000 Hz
Note
These audio format restrictions are enforced by the webpage.
You can use the free utility Audacity to convert audio files into this format. See Figure 2-26 through
Figure 2-28.
Figure 2-26. Audacity 1
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 55
Configure the Audio Parameters
Figure 2-27. Audacity 2
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 56
Configure the Audio Parameters
When you export an audio file with Audacity, save the output as:
•
WAV (Microsoft) signed 16 bit PCM.
Figure 2-28. WAV (Microsoft) signed 16 bit PCM
WAV (Microsoft) signed 16 bit PCM
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 57
Configure the Event Parameters
2.4.13 Configure the Event Parameters
Click on the Events button to open the Events page (Figure 2-29). The Events page specifies a
remote server that can be used to receive HTTP POST events when actions take place on the
board.
Figure 2-29. Events Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 58
Configure the Event Parameters
Table 2-18 shows the web page items on the Events page.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-18. Events Configuration
Web Page Item
Description
Enable Event Generation
The device will send HTTP POST events to the specified remote server and port
number whenever a certain action takes place. Select an event type below to
generate an HTTP POST event. See Section 2.4.13.1, "Example Packets for
Events" for sample packets.
Events
Enable Call Start Events
When selected, the device will report the start of a SIP call.
Enable Call Terminated Events
When selected, the device will report the end of a SIP call.
Enable Relay Activated Events
When selected, the device will report relay activation.
Enable Relay Deactivated Events
When selected, the device will report relay deactivation.
Enable Night Ring Events
When selected, the device will report when it starts ringing upon an incoming SIP
call to the Nightringer extension. As a reminder, the Nightringer extension always
rings upon an incoming SIP call and it is not possible to alter this behavior.
Enable Power On Events
When selected, the device will report when it boots.
Enable Fault Events
When selected, the device will report when the on-board fault detection is
activated.
Enable 60 Second Heartbeat
When enabled, the device will report a Heartbeat event every 60 seconds. SIP
registration is not required to generate Heartbeat events.
Event Server
Server IP Address
The IPv4 address of the event server in dotted decimal notation.
Server Port
Specify the event server port number. The supported range is 0-65536. Enter up
to 5 digits.
Server URL
Generally, the destination URL is the name of the application that receives the
events and the string in the HTTP POST command. It can be a script used to
parse and process the HTTP POST events. Enter up to 127 characters.
Check All
Click on Check All to select all of the events on the page.
Uncheck All
Click on Uncheck All to de-select all of the events on the page.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the web
page items. First click on the Toggle Help button, and you will see a question
mark ( ) appear next to some of the web page items. Move the mouse pointer to
hover over a question mark to see a short description of a specific web page
item.
Note
CyberData Corporation
You must click on the Save button and then the Reboot button for the changes to take
effect.
931073J
Operations Guide
Setting Up the SIP Paging Server 59
Configure the Event Parameters
2.4.13.1 Example Packets for Events
The server and port are used to point to the listening server and the 'Remote Event Server URL' is
the destination URL (typically the script running on the remote server that's used to parse and
process the POST events).
Note
The XML is URL-encoded before transmission so the following examples are not completely
accurate.
Here are example packets for every event:
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>POWERON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 199
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>HEARTBEAT</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 196
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>BUTTON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 201
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>CALL_ACTIVE</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 60
Configure the Event Parameters
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 205
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>CALL_TERMINATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RINGING</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>MULTICAST_START</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 233
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>MULTICAST_STOP</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RELAY_ACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 61
Configure the Event Parameters
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RELAY_DEACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>NIGHTRINGING</event>
</cyberdata>
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 62
Configure the Autoprovisioning Parameters
2.4.14 Configure the Autoprovisioning Parameters
Autoprovisioning can be used to automatically configure your device. The autoprovisioning file is an
xml file with the device configuration. Values found in this file will override values stored in on-board
memory.
Note
By default, the device will try to set up its configuration with autoprovisioning.
1. Click the Autoprov menu button to open the Autoprovisioning page. See Figure 2-30.
Figure 2-30. Autoprovisioning Page
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 63
Configure the Autoprovisioning Parameters
2. On the Autoprovisioning page, you may enter values for the parameters indicated in Table 219.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-19. Autoprovisioning Configuration Parameters
Web Page Item
Description
Disable Autoprovisioning
Prevent the device from automatically trying to download a
configuration file. See Section 2.4.14.1, "Autoprovisioning" for
more information.
Autoprovisioning Server
Enter the IPv4 address of the provisioning server in dotted
decimal notation.
Autoprovisioning Filename
The autoprovisioning filename is the configuration filename.
The default autoprovisioning filename is in the format of
<mac address>.xml.
Supported filename extensions are “.txt”, and “.xml.” The
current filename is denoted by an asterisk at the bottom of
the Autoprovisioning Page. Enter up to 256 characters.
A file may have any name with an xml extension. If a file
name is entered, the device will look for the specified file
name, and only that file.
Use tftp
The device will use TFTP (instead of http) to download
autoprovisioning files.
Username
The username used to authenticate with an autoprovisioning
server. Leave this field blank to disable authentication.
Password
The password used to authenticate with an autoprovisioning
server. Leave this field blank to disable authentication.
Autoprovisioning autoupdate 
(in minutes)
The reoccurring time (in minutes) the device will wait before
checking for new autoprovisioning files. Enter up to 6 digits. A
value of 0 will disable this option.
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device Page
page (see Table 2-5).
Autoprovision at time (HHMMSS)
The time of day the device will check for a new
autoprovisioning file. The time must be 6 characters in length
and in HHMMSS format. An empty value will disable this
option.
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device Page
page (see Table 2-5).
Autoprovision when idle
(in minutes > 10)
The idle time (in minutes greater than 10) after which the
device will check for a new autoprovisioning file. Enter up to 6
digits. A value of 0 will disable this option.
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device Page
page (see Table 2-5).
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 64
Configure the Autoprovisioning Parameters
Table 2-19. Autoprovisioning Configuration Parameters (continued)
Web Page Item
Description
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to
hover over a question mark to see a short description of a
specific web page item.
Press the Download Template button to create an
autoprovisioning file for the device. See Section 2.4.14.3,
"Get Autoprovisioning Template Button"
Autoprovisioning log
Note
The autoprovisioning log provides information about the latest
autoprovisioning attempt (i.e. dhcp options and server
accessed and files parsed or not found).
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.4.14.1 Autoprovisioning
On boot, the device will look for an autoprovisioning server configured on the Autoprovisioning Page
or specified as a DHCP option. When it finds a server, it will try to download the following (in order of
preference):
1. The file configured on the autoprovisioning page.
2. A file named according to it's mac address (for example: 0020f7350058.xml).
3. The file 000000cd.xml
The file can be hosted using a standard web server (like apache, IIS, or nginx), and the device can
download over SSL. The file server can be an ipv4 address in dotted decimal notation or a fully
qualified domain name.
By default, the device will get its autoprovisioning server from the DHCP options. See Section
2.4.14.2, "Sample dhcpd.conf" for an example of how to configure dhcpd to offer autoprovisioning
server addresses. If multiple options are set, the device will attempt to download autoprovisioning
files from every server.
The DHCP option determines the protocol used to download the autoprovisioning file. The device
looks for DHCP options in the following order:
1. Option 43 - a FQDN or an IP address to an http server
2. Option 72 - an IP address to an http server
3. Option 150 - an IP address to a tftp server
4. Option 66 - an IP address to a tftp server or if the entry starts with 'http', a FQDN to a http server.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 65
Configure the Autoprovisioning Parameters
You can download an autoprovisioning template file from the Autoprovisioning Page using the
Download Template button (see Table 2-19). This file contains every configuration option that can
be set on the board.
Autoprovisioning files can contain the whole configuration or a subset of this file. The first
autoprovisioning file can also contain links to other autoprovisioning files.
The <MiscSettings> section contains some examples of additional autoprovisioning files:
<MiscSettings>
<DeviceName>CyberData VoIP Intercom</DeviceName>
<!-<AutoprovFile>common.xml</AutoprovFile>-->
<!-<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>-->
<!-<AutoprovFile>audio[macaddress]</AutoprovFile>-->
<!-<AutoprovFile>device[macaddress].xml</AutoprovFile>-->
</MiscSettings>
After downloading the first autoprovisioning file, the device will step through up to twenty additional
<AutoprovFile> entries and try to download these files from the same server.
When the device finds a filename with the string [macaddress], it will replace this string with the
mac address.
As an example, the user has configured option 43 on their DHCP server to “http://example.com,” and
on their server, they have a file named 0020f7123456.xml (the same as the mac address of the
device).
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 66
Configure the Autoprovisioning Parameters
The file 0020f7123456.xml contains:
<?xml version="1.0" encoding="utf-8" ?>
<specific>
<MiscSettings>
<DeviceName>Newname</DeviceName>
<AutoprovFile>common.xml</AutoprovFile>
<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>
<AutoprovFile>audio[macaddress]</AutoprovFile>
<AutoprovFile>device.xml</AutoprovFile>
</MiscSettings>
</specific>
1. The device will first set it's name to 'Newname'.
2. It will try to download http://example.com/common.xml.
3. It will try to download http://example.com/sip_reg0020f7123456.xml.
4. It will try to download http://example.com/audio0020f7123456.
5. It will try to download http://example.com/device.xml.
The device is reconfigured every time it downloads a new file so if two files configure the same
option the last one will be the one that is saved.
It is possible to autoprovision autoprovisioning values (for example, to disable autoprovisioning or to
configure a time to check for new files).
Checking for New The device will always check for an autoprovisioning files on boot but it can be configured to also
Autoprovisioning check after a periodic delay, when idle, or at a specified time. When one of these options is set, the
Files after Boot
device will download its autoprovisioning files again, and if it finds any differences from the files it
downloaded on boot, it will force a reboot and reconfigure.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 67
Configure the Autoprovisioning Parameters
The
Autoprovisioning
Filename
The autoprovisioning filename can contain a file, a file path, or a directory.
Table 2-20. Autoprovisioning File Name
Autoprovisioning
Filename
Autoprovisioning
Server
File Downloaded
config.xml
10.0.1.3
10.0.1.3/config.xml
/path/to/config.xml
10.0.1.3
10.0.1.3/path/to/config.xml
subdirectory/path/
10.0.1.3
10.0.1.3/subdirectory/path/0020f7020002.xml
TFTP options may not support subdirectories. If a directory is set in the filename field, firmware and
audio files will also be downloaded from this subdirectory.
If the filename ends with a forward slash “/,” the device will treat it as a subdirectory.
For example:
The autoprovisioning server is set to “https://www.example.com”
The autoprovisioning filename is set to “cyberdata/”
On boot, the device will try to download:
https://www.example.com/cyberdata/0020f7123456.xml
...and if this fails:
https://www.example.com/cyberdata/000000cd.xml
Audio files and firmware files will also add “cyberdata” to the URL before downloading.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 68
Configure the Autoprovisioning Parameters
Autoprovisioning <FirmwareSettings>
Firmware Updates
<FirmwareFile>505-uImage-ceilingspeaker</FirmwareFile>
<FirmwareServer>10.0.1.3</FirmwareServer>
<OutdoorIntercom30>firmware_file_v9.3.0</OutdoorIntercom30>
<OutdoorIntercom31>firmware_file_v10.3.0</OutdoorIntercom31>
<CallButton31>firmware_file_v10.3.0</CallButton31>
</FirmwareSettings>
In the <FirmwareSettings> section, the <FirmwareServer> element can be used to specify a
different server for hosting firmware files. When this element is not available, the device will try to
download the file from the autoprovisioning server.
The device will use the filename to determine when to autoprovision firmware updates. The default
configuration is blank, so the first time you set a value in your autoprovisioning file, it may force a
firmware update even if the firmware version has not changed.
The <FirmwareFile> name can contain path elements (i.e. /path/to/firmware/10.3.0-uImage[device_file_name]).
The device also supports product strings for downloading firmware. If the <FirmwareFile> option is
not set, the device will look for its particular product string for a firmware filename. In this way, a
generic autoprovisioning file can specify unique firmware for a range of products.
The list of valid product strings:
<ProductString>CallButton31</ProductString>
<ProductString>EmergencyIntercom31</ProductString>
<ProductString>EmergencyIntercom31SW</ProductString>
<ProductString>IndoorIntercom31</ProductString>
<ProductString>IndoorIntercom31SW</ProductString>
<ProductString>IndoorKeypad31</ProductString>
<ProductString>IndoorKeypad31SW</ProductString>
<ProductString>OfficeRinger31</ProductString>
<ProductString>OfficeRinger31SW</ProductString>
<ProductString>OutdoorIntercom31</ProductString>
<ProductString>OutdoorIntercom31SW</ProductString>
<ProductString>OutdoorKeypad31</ProductString>
<ProductString>OutdoorKeypad31SW</ProductString>
<ProductString>Strobe31</ProductString>
<ProductString>Strobe31SW</ProductString>
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 69
Configure the Autoprovisioning Parameters
Autoprovisioning
Example 1
Here's a simple example using four autoprovisioning files to configure two devices:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2).
The devices are set to use DHCP and that server provides an autoprovisioning server address with
option 43. The address is “https://autoprovtest.server.net.” The files on this server are as follows:
000000cd.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
<AutoprovFile>sip_common.xml</AutoprovFile>
<AutoprovFile>sip_[macaddress].xml</AutoprovFile>
</MiscSettings>
sip_common.xml
<SIPSettings>
<SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
sip_0020f7020001.xml
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
sip_0020f7020002.xml
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
On boot, Device1 tries to fetch the file 0020f7023614.xml from “https://autoprovtest.server.net”. This
file is not available, so device1 then tries to fetch the file 000000cd.xml. This file exists, and Device1
parses the three elements.
1. Device1 changes its device name to CyberData Autoprovisioned.
2. Device1 finds an AutoprovFile element containing the filename sip_common.xml. The device
downloads sip_common.xml from “https://autoprovtest.server.net,” and imports this
configuration, setting the sip server to 10.0.0.253 and the remote port to 5060.3.
3. Device1 finds another AutoprovFile element containing the filename sip_[macaddress].xml.
The device replaces the [macaddress] with its own mac address value creating
sip_0020f7020001.xml, downloads this file from “https://autoprovtest.server.net,” and imports
this configuration. This sets the user ID to 198, the password to ext198, and the dialout
extension to 204. Device1 is now finished with autoprovisioning.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 70
Configure the Autoprovisioning Parameters
Device2 goes through the same steps by setting its device name to CyberData Autoprovisioned,
its SIP server to 10.0.0.253, and its port to 5060. When Device2 “sees” sip_[macaddress].xml,
Device2 replaces it with its own mac address and downloads sip_0020f7020002.xml from
“https://autoprovtest.server.net.” Device2 sets the SIP User ID to 500, the password to ext500, and
the dialout extension to 555.
Autoprovisioning
Example 2
Here is another example of setting up your autoprovisioning files:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2) and boot them on a network with a DHCP server configured with an autoprovisioning
server at 10.0.1.3 on option 150. Our TFTP server has three files:
0020f7020001.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
0020f7020002.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
common_settings.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
</MiscSettings>
<SIPSettings> <SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
1. On boot, Device1 downloads 0020f7020001.xml from 10.0.1.3 and imports these values. The SIP
User ID is 198, the password is ext198, and the dialout extension is 204.
2. Device1 then gets the filename common_settings.xml from the AutoprovFile element and
downloads this file from the TFTP server at 10.0.1.3. and imports these settings. The device name is
set to CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Device2 does the same except it downloads 0020f7020002.xml on boot and imports these values
instead. The Sip User ID is 500, password is ext500, and dialout extension is 555. Device2 then
downloads the common_settings.xml file and imports those values. The device name is set to
CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 71
Configure the Autoprovisioning Parameters
XML Files
XML files can contain <AutoprovFile> elements. If multiple DHCP options are specified, the device
will try to download autoprovisioning files from each in turn. The device will only look for
<AutoprovFile> elements in the first file downloaded from each server. You can specify up to 20
<AutoprovFile> elements in the first autoprovisioning file.
There are numerous ways to change an element of the configuration(xml) file. Using sip ext as an
example, the extension can be changed:
Within the device-specific xml, i.e. [macaddress].xml, via the AutoprovFile
element:<SIPSettings>/<SIPExt>
From the device specific xml, a pointer to a sip_common file
From the device specific xml, a pointer to the device specific sip_[macaddress].xml
From the common file, a pointer to sip_common.xml
From the common file, a pointer to the device specific (sip_[macaddress].xml)
Autoprovisioned
Audio Files
Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be
downloaded once for each device. Loading many audio files to the device from the web page could
cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh
the page.
The device uses the file name to determine when to download a new audio file. This means that if
you used autoprovisioning to upload a file and then changed the contents of this file at the TFTP
server, the device will not recognize that the file has changed (because the file name is the same).
Since audio files are stored in non-volatile memory, if autoprovisioning is disabled after they have
been loaded to the board, the audio file settings will not change. You can force a change to the audio
files on the board by clicking Restore Default on the Audio Configuration page or by changing the
autoprovisioning file with “default” set as the file name.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 72
Configure the Autoprovisioning Parameters
2.4.14.2 Sample dhcpd.conf
#
# Sample configuration file for ISC dhcpd for Debian
#
ddns-update-style none;
option domain-name "voiplab";
option domain-name-servers 10.0.0.252;
option option-150 code 150 = ip-address;
option ntp-servers north-america.pool.ntp.org;
option space VendorInfo;
option VendorInfo.text code 10 = { text };
authoritative;
log-facility local7;
subnet 10.0.0.0 netmask 255.0.0.0 {
max-lease-time 3600;
default-lease-time 3600;
option routers
option subnet-mask
10.0.0.1;
255.0.0.0;
option domain-name
option domain-name-servers
"voiplab";
10.0.0.252;
option time-offset
-8;
# Pacific Standard Time
#
option www-server
99.99.99.99;
#
#
option tftp-server-name
option tftp-server-name
"10.0.1.52";
"http://test.cyberdata.net";
# OPTION 66
# OPTION 66
#
option option-150
10.0.0.252;
# OPTION 150
# These two lines are needed for option 43
#
vendor-option-space VendorInfo;
#
option VendorInfo.text "http://test.cyberdata.net";
# OPTION 72
# OPTION 43
# OPTION 43
range 10.10.0.1 10.10.2.1; }
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 73
Configure the Autoprovisioning Parameters
2.4.14.3 Get Autoprovisioning Template Button
The Get Autoprovisioning Template button allows the user to generate, download, edit, and then
store an autoprovisioning template on the server that serves the autoprovisioning files for devices.
To generate an autoprovisioning template directly from the device, complete the following steps:
1. On the Autoprovisioning page, click on the Get Autoprovisioning Template button.
2. You will see a window prompting you to save a configuration file (.xml) to a location on your
computer (Figure 2-31). The configuration file is the basis for the default configuration settings
for your unit).
3. Choose a location to save the configuration file and click on OK. See Figure 2-31.
Figure 2-31. Configuration File
4. At this point, you can open and edit the autoprovisioning template to change the configuration
settings in the template for the unit.
5. You can then upload the autoprovisioning file to a TFTP or HTTP server where the file can be
loaded onto other devices.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 74
Upgrade the Firmware
2.5 Upgrading the Firmware
Caution
Equipment Hazard: Devices with a serial number that begins with 1461xxxxx can
only run firmware versions 11.0.0 or later.
GENERAL ALERT
2.5.1 Upgrade the Firmware
To upload the firmware from your computer:
1. Retrieve the latest SIP Paging Server firmware from the SIP Paging Server Downloads page at:
https://www.cyberdata.net/products/011146
2. Unzip the firmware version file. This file may contain the following:
•
Firmware file
•
Release notes
3. Log in to the SIP Paging Server home page as instructed in 2.4.4 "Log in to the Configuration
GUI".
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 75
Upgrade the Firmware
4. Click on the Firmware menu button to open the Firmware page. See Figure 2-32.
Caution
GENERAL ALERT
Equipment Hazard: CyberData strongly recommends that you first reboot the
device before attempting to upgrade the firmware of the device. See Section 2.5.2,
"Reboot the SIP Paging Server".
Figure 2-32. Firmware Page
v12.1.0
5. Click on the Browse button, and then navigate to the location of the firmware file.
6. Select the firmware file.
7. Click on the Upload button.
Note
Do not reboot the device after clicking on the Upload button.
Note
This starts the upgrade process. Once the SIP Paging Server has uploaded the file, the
Uploading Firmware countdown page appears, indicating that the firmware is being written
to flash. The SIP Paging Server will automatically reboot when the upload is complete.
When the countdown finishes, the Firmware page will refresh. The uploaded firmware
filename should be displayed in the system configuration (indicating a successful upload
and reboot).
8. Table 2-21 shows the web page items on the Firmware page.
Table 2-21. Firmware Parameters
Web Page Item
Description
Current Firmware Version
Shows the current firmware version.
Use the Browse button to navigate to the location of the
Intercom firmware file that you want to upload.
Click on the Upload button to automatically upload the selected
firmware and reboot the system.
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 76
Reboot the SIP Paging Server
2.5.2 Reboot the SIP Paging Server
To reboot a SIP Paging Server, log in to the web page as instructed in Section 2.4.4, "Log in to the
Configuration GUI".
1. Click Reboot (Figure 2-33). A normal restart will occur.
Figure 2-33. Home Page
146100001
v12.1.0
Reboot
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 77
Command Interface Post Commands
2.6 Command Interface
Some functions on the device can be activated using simple POST commands to the web interface.
The examples in Table 2-22 use the free unix utility, wget commands. However, any program that
can send HTTP POST commands to the device should work.
2.6.1 Command Interface Post Commands
These commands require an authenticated session (a valid username and password to work).
Table 2-22. Command Interface Post Commandsa
Device Action
HTTP Post Command
Trigger relay (fixed at 5 seconds)
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi- bin/command.cgi" --post-data
"test_relay=yes"
Terminate active call
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi- bin/command.cgi" --post-data
"terminate=yes"
Force reboot
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi- bin/command.cgi" --post-data
"reboot=yes"
Play “audio test message”
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi- bin/command.cgi" --post-data
"test_audio=yes"
Announce IP address
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi- bin/command.cgi" --post-data
"speak_ip_address=yes"
Play the "0" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_0=yes"
Play the "1" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_1=yes"
Play the "2" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_2=yes"
Play the "3" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet - O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_3=yes"
Play the "4" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_4=yes"
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_5=yes"
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 78
Command Interface Post Commands
Table 2-22. Command Interface Post Commandsa (continued)
Device Action
HTTP Post Command
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_6=yes"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_7=yes"
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_8=yes"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_9=yes"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data "play_d=yes"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_pagetone=yes"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_youripaddressis=yes"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_rebooting=yes"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_restoringdefault=yes"
Play the "Sensor Triggered" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_sensortriggered=yes"
Play the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_nightring=yes"
Play the "Enter PGROUP" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_enterpgroup=yes"
Play the "Invalid PGROUP" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_invalidpgroup=yes"
Play the "Enter Code" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_entercode=yes"
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 79
Command Interface Post Commands
Table 2-22. Command Interface Post Commandsa (continued)
Device Action
HTTP Post Command
Play the "Invalid Code" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"play_invalidcode=yes"
Delete the "0" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_0=yes"
Delete the "1" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_1=yes"
Delete the "2" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_2=yes"
Delete the "3" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_3=yes"
Delete the "4" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_4=yes"
Delete the "5" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_5=yes"
Delete the "6" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_6=yes"
Delete the "7" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_7=yes"
Delete the "8" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_8=yes"
Delete the "9" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_9=yes"
Delete the "Audio Test" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_audiotest=yes"
Delete the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_pagetone=yes"
CyberData Corporation
931073J
Operations Guide
Setting Up the SIP Paging Server 80
Command Interface Post Commands
Table 2-22. Command Interface Post Commandsa (continued)
Device Action
HTTP Post Command
Delete the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_youripaddressis=yes"
Delete the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_rebooting=yes"
Delete the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_restoringdefault=yes"
Delete the "Sensor Triggered" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_sensortriggered=yes"
Delete the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_nightring=yes"
Delete the "Enter PGROUP" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_enterpgroupl=yes"
Delete the "Invalid PGROUP" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_invalidpgroup=yes"
Delete the "Enter Code" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_entercode=yes"
Delete the "Invalid Code" audio file
wget --user admin --password admin --auth-no-challenge --no-check-certificate -quiet -O /dev/null "https://10.0.3.71/cgi-bin/audiofiles.cgi" --post-data
"delete_invalidcode=yes"
a.Type and enter all of each http POST command on one line.
CyberData Corporation
931073J
Operations Guide
81
Appendix A: Setting Up a TFTP Server
A.1 Set up a TFTP Server
Autoprovisioning requires a TFTP server for hosting the configuration file.
A.1.1 In a LINUX Environment
To set up a TFTP server on LINUX:
1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that
directory.
2. Run the following command where /tftpboot/ is the path to the directory you created in
Step 1: the directory that contains the files to be uploaded. For example:
in.tftpd -l -s /tftpboot/your_directory_name
A.1.2 In a Windows Environment
You can find several options online for setting up a Windows TFTP server. This example explains
how to use the Solar Winds freeware TFTP server, which you can download at:
http://www.cyberdata.net/support/voip/solarwinds.html
To set up a TFTP server on Windows:
1. Install and start the software.
2. Select File/Configure/Security tab/Transmit Only.
Make a note of the default directory name, and then move the firmware files to be uploaded to that
directory.
CyberData Corporation
931073J
Operations Guide
82
Appendix B: Troubleshooting/Technical
Support
B.1 Frequently Asked Questions (FAQ)
To see a list of frequently asked questions for your product, click on the FAQs tab at the following
webpage:
https://www.cyberdata.net/products/011146
B.2 Documentation
The documentation for this product is released in an English language version only.
To download PDF copies of CyberData product documentation, click on the Downloads tab at the
following webpage:
https://www.cyberdata.net/products/011146
CyberData Corporation
931073J
Operations Guide
83
Contact Information
B.3 Contact Information
Contact
CyberData Corporation
3 Justin Court
Monterey, CA 93940 USA
www.CyberData.net
Phone: 800-CYBERDATA (800-292-3732)
Fax: 831-373-4193
Sales
Sales 831-373-2601, Extension 334
Technical 
Support
The fastest way to get technical support for your VoIP product is to submit a VoIP Technical
Support form at the following website:
http://support.cyberdata.net/
The Support Form initiates a ticket which CyberData uses for tracking customer requests. Most
importantly, the Support Form tells us which PBX system and software version that you are
using, the make and model of the switch, and other important information. This information is
essential for troubleshooting. Please also include as much detail as possible in the Comments
section of the Support Form.
Phone: (831) 373-2601, Extension 333
B.4 Warranty and RMA Information
The most recent warranty and RMA information is available at the following website address:
http://support.cyberdata.net/
CyberData Corporation
931073J
Operations Guide
84
Index
changing default username and password for
configuration GUI 18
Cisco SRST 33
command interface 77
commands 77
configurable parameters 23, 30, 33
configuration information 14
configuration page
configurable parameters 23, 30
connecting the V3 paging server 7
connection speed 12
verifying 12
connector (removable) 9
contact information 83
contact information for CyberData 83
current network settings 30
current settings, reviewing 21
CyberData contact information 83
Symbols
+48V DC power supply 10
Numerics
100 Mbps indicator light 12
A
activity light 12
address, configuration login 18
addressing
DHCP 14, 31
static 14, 31
admin username and password 18
audio configuration 51
night ring tone parameter 53
audio configuration page 51
audio ground reference 8
audio output 8
authenticate ID and password for SIP server
registration 36
autoprovision at time (HHMMSS) 63
autoprovision when idle (in minutes > 10) 63
autoprovisioning 64
download template button 64
autoprovisioning autoupdate (in minutes) 63
autoprovisioning configuration 62, 63
autoprovisioning filename 63
autoprovisioning server (IP Address) 63
D
default
gateway 13
IP address 13
subnet mask 13
username and password 13
default gateway 13, 30
default gateway for static addressing 31
default login address 18
default password for configuration GUI 18
default settings, restoring 13
default username and password for configuration GUI 18
device configuration 22
device configuration parameters 63
the device configuration page 62
device configuration page 22
device configuration parameters 23
device configuration password
changing for web configuration access 22
DHCP addressing 14, 31
dimensions 3
discovery utility program 18
DNS server 30
door sensor 53
download autoprovisioning template button 64
B
backup SIP server 1 33
backup SIP server 2 33
backup SIP servers, SIP server
backups 33
C
cat 5 ethernet cable 10
changing
the web access password 22
CyberData Corporation
931073J
Operations Guide
85
E
L
enable night ring events 58
ethernet port 10
event configuration
enable night ring events 58
expiration time for SIP server lease 34, 35, 36
export settings 20
lease, SIP server expiration time 34, 35, 36
line input specifications 3
line output specifications 3
line-in 7
line-out 7
link light 12
Linux, setting up a TFTP server on 81
local SIP port 34, 36
log in address 18
logging in to configuration GUI 18
F
fault sense input, sensor 8
features 2
firmware
where to get the latest firmware 74
firmware, upgrade 74
M
MGROUP 38
multicast
play line-in audio via multicast 50
play stored audio via multicast 50
multicast address 50
multicast port 50
multicast TTL 41, 43
G
get autoprovisioning template 64
GMT table 27
GMT time 27
ground connection 7
GUI username and password 18
N
navigation (web page) 15
navigation table 15
network activity, verifying 12
network configuration page 29
network parameters, configuring 29
network setup button 29
network, connecting to 11
Nightringer 73
nightringer settings 34
NTP server 23
H
hazard levels 4
http POST command 77
I
identifier names (PST, EDT, IST, MUT) 27
identifying your product 1
import settings 20
import/export settings 20
input specifications 3
intercom configuration page
configurable parameters 33
IP address 13, 30
SIP server 36
IP addressing
default
IP addressing setting 13
O
orange link LED 12
out of band 44
output specifications 3
P
page port 8
page port output connections 8
paging server
configuration 14
CyberData Corporation
931073J
Operations Guide
86
part number 3
parts list 5
password
configuration GUI 14, 18
for SIP server login 33
restoring the default 13
SIP server authentication 36
pgroups 38
pin descriptions and functions 8
point-to-point configuration 37
port
ethernet 10
local SIP 34, 36
remote SIP 34, 36
posix timezone string
timezone string 23
POST command 77
power
connecting to 10
product overview 1
outbound proxy 34, 35
registration and expiration, SIP server lease 34, 35
unregister on reboot 34
user ID, SIP 33
SIP registration 33
SIP remote SIP port 34
SIP server 33
password for login 33
unregister from 34
user ID for login 33
SIP server configuration 33
SIP server parameters, configuring 14
SIP setup button 32
specifications 3
SRST 33
static addressing 14, 31
status light 12
subnet mask 13, 30
subnet mask static addressing 31
supported protocols 3
R
T
reboot 75, 76
unregistering from SIP server during 36
registration and expiration, SIP server
lease expiration 36
relay 8
relay contact 8
remote SIP port 34, 36
required configuration for web access username and
password 14, 18
resetting the IP address to the default 82
restoring factory default settings 13
RFC2833 RTP events 44
rport discovery setting, disabling 34
tech support 83
technical support, contact information 83
TFTP server 81
time zone string examples 27
U
unregister from SIP server 36
upgrade firmware 74
user ID
for SIP server login 33
user ID for SIP server registration 36
username
changing for web configuration access 22
restoring the default 13
username for configuration GUI 14, 18
S
safety instructions 5
sales 83
server
TFTP 81
server address, SIP 33
service 83
set time with external NTP server on boot 23
SIP
enable SIP operation 33
local SIP port 34
user ID 33
SIP configuration page 32
SIP configuration parameters
CyberData Corporation
V
verifying
connection speed 12
network activity 12
network connectivity 12
VLAN ID 30
VLAN Priority 30
VLAN tagging support 30
VLAN tags 30
931073J
Operations Guide
87
W
warranty policy at CyberData 83
web access password 13
web access username 13
web configuration log in address 18
web page
navigation 15
web page navigation 15
wget commands 77
wget, free unix utility 77
Windows, setting up a TFTP server on 81
CyberData Corporation
931073J
Operations Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising